Skip to contentSkip to conversation

GCOV: Add config to check the preqequisites situation

PATCH In review [email protected] 2 participants 2 messages Oct 28, 2020 – Oct 30, 2020

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH v8 1/1 GCOV: Add config to check the preqequisites situation

From: Cixi Geng <[email protected]>

Introduce new configuration option GCOV_PROFILE_PREREQS that can be used to check whether the prerequisites for enabling gcov profiling for specific files and directories are met.

Only add SERIAL_GCOV for an example.

---
 drivers/tty/serial/Kconfig  | 7 +++++++
 drivers/tty/serial/Makefile | 1 +
 kernel/gcov/Kconfig         | 9 +++++++++
 3 files changed, 17 insertions(+)
drivers/tty/serial/Kconfig +7 -0
index 1044fc387691..fa33710c8435 100644
@@ -1586,3 +1586,10 @@ endmenu
 
 config SERIAL_MCTRL_GPIO
 	tristate
+
+config SERIAL_GCOV
+	bool "Enable profile gcov for serial directory"
+	depends on GCOV_PROFILE_PREREQS
+	help
+	  The SERIAL_GCOV will add Gcov profiling flags when kernel compiles.
+	  Say 'Y' here if you want the gcov data for the serial directory,
drivers/tty/serial/Makefile +1 -0
index caf167f0c10a..4a4934622c3f 100644
@@ -3,6 +3,7 @@
 # Makefile for the kernel serial device drivers.
 #
 
+GCOV_PROFILE := $(CONFIG_SERIAL_GCOV)
 obj-$(CONFIG_SERIAL_CORE) += serial_core.o
 
 obj-$(CONFIG_SERIAL_EARLYCON) += earlycon.o
kernel/gcov/Kconfig +9 -0
index 3110c77230c7..ce9b8ce4e63b 100644
@@ -51,4 +51,13 @@ config GCOV_PROFILE_ALL
 	larger and run slower. Also be sure to exclude files from profiling
 	which are not linked to the kernel image to prevent linker errors.
 
+config GCOV_PROFILE_PREREQS
+	bool "Profile Kernel for prereqs"
+	def_bool y if GCOV_KERNEL && !COMPILE_TEST
+	help
+	  This options activates profiling for the specified kernel modules.
+	  When some modules need Gcov data, enable this config, then configure
+	  with gcov on the corresponding modules,The directories or files of
+	  these modules will be added profiling flags after kernel compile.
+
 endmenu
Signature · 1 line
2.25.1
#1 lore raw
Quoted 7 lines · On 28.10.2020 14:15, [email protected] wrote:

From: Cixi Geng <[email protected]>

Introduce new configuration option GCOV_PROFILE_PREREQS that can be used to check whether the prerequisites for enabling gcov profiling for specific files and directories are met.

Only add SERIAL_GCOV for an example.

[...]

kernel/gcov/Kconfig config GCOV_PROFILE_ALL · line 63

Quoted 10 lines
kernel/gcov/Kconfig +9 -0
+config GCOV_PROFILE_PREREQS
+	bool "Profile Kernel for prereqs"
+	def_bool y if GCOV_KERNEL && !COMPILE_TEST
+	help
+	  This options activates profiling for the specified kernel modules.
+	  When some modules need Gcov data, enable this config, then configure
+	  with gcov on the corresponding modules,The directories or files of
+	  these modules will be added profiling flags after kernel compile.
+
 endmenu

This version still produces a prompt during make oldconfig. You need to remove the "bool" line and the "help" lines.

Before sending another version please test it to make sure that it does not produce a prompt.

Signature · 2 lines
Peter Oberparleiter
Linux on Z Development - IBM Germany