Fix FSP-3Y YH-5151E non-compliant vout encoding
PATCH v3 1/1 Fix FSP-3Y YH-5151E non-compliant vout encoding
I didn't properly test the driver for YH-5151E, so it was completely broken. Firstly, the log/real mapping was incorrect in one case. Secondly, PMBus specifies that output voltages should be in the linear16 encoding. However, the YH-5151E is non-compliant and uses linear11. YM-2151E isn't affected by this. Fix this by converting the values inside the read functions. linear16 gets the exponent from the VOUT_MODE command. The device doesn't support it, so I have to manually supply the value for it.
Both supported devices have now been tested to report correct vout values.
--- drivers/hwmon/pmbus/fsp-3y.c | 27 +++++++++++++++++++++++++-- 1 file changed, 25 insertions(+), 2 deletions(-)
drivers/hwmon/pmbus/fsp-3y.c +25 -2
@@ -57,7 +57,7 @@ static int page_log_to_page_real(int page_log, enum chips chip)case YH5151E_PAGE_12V_LOG :return YH5151E_PAGE_12V_REAL ;case YH5151E_PAGE_5V_LOG : -return YH5151E_PAGE_5V_LOG ; +return YH5151E_PAGE_5V_REAL ;case YH5151E_PAGE_3V3_LOG :return YH5151E_PAGE_3V3_REAL ; }
@@ -103,8 +103,18 @@ static int set_page(struct i2c_client *client, int page_log)static int fsp3y_read_byte_data (struct i2c_client *client,int page,int reg) { +const struct pmbus_driver_info *info =pmbus_get_driver_info (client); +struct fsp3y_data *data =to_fsp3y_data (info);int rv; +/* +* YH5151-E outputs vout in linear11. The conversion is done when +* reading. Here, we have to inject pmbus_core with the correct +* exponent (it is -6). +*/ +if (data->chip == yh5151e && reg ==PMBUS_VOUT_MODE ) +return 0x1A ; + rv =set_page (client, page);if (rv <0 )return rv;
@@ -114,6 +124,8 @@ static int fsp3y_read_byte_data(struct i2c_client *client, int page, int reg)static int fsp3y_read_word_data (struct i2c_client *client,int page,int phase,int reg) { +const struct pmbus_driver_info *info =pmbus_get_driver_info (client); +struct fsp3y_data *data =to_fsp3y_data (info);int rv;/*
@@ -144,7 +156,18 @@ static int fsp3y_read_word_data(struct i2c_client *client, int page, int phase,if (rv <0 )return rv; -return i2c_smbus_read_word_data (client, reg); + rv =i2c_smbus_read_word_data (client, reg); +if (rv <0 ) +return rv; + +/* +* YH-5151E is non-compliant and outputs output voltages in linear11 +* instead of linear16. +*/ +if (data->chip == yh5151e && reg ==PMBUS_READ_VOUT ) + rv =sign_extend32 (rv,10 ) &0xffff ; + +return rv; }struct pmbus_driver_info fsp3y_info[] = {
Signature · 1 line
2.31.1
Quoted 9 lines · Václav Kubernát
I didn't properly test the driver for YH-5151E, so it was completely broken. Firstly, the log/real mapping was incorrect in one case. Secondly, PMBus specifies that output voltages should be in the linear16 encoding. However, the YH-5151E is non-compliant and uses linear11. YM-2151E isn't affected by this. Fix this by converting the values inside the read functions. linear16 gets the exponent from the
VOUT_MODEcommand. The device doesn't support it, so I have to manually supply the value for it.
Quoted 5 lines
Both supported devices have now been tested to report correct vout values.
Fixes 1734b4135a62 ("hwmon: Add driver for fsp-3y PSUs and PDUs")Signed-off-by Václav Kubernát <[email protected]>
Applied.
Thanks,
Guenter
Quoted 65 lines
--- drivers/hwmon/pmbus/fsp-3y.c | 27 +++++++++++++++++++++++++-- 1 file changed, 25 insertions(+), 2 deletions(-)drivers/hwmon/pmbus/fsp-3y.c +25
-2@@ -57,7 +57,7 @@ static int page_log_to_page_real(int page_log, enum chips chip)case YH5151E_PAGE_12V_LOG :return YH5151E_PAGE_12V_REAL ;case YH5151E_PAGE_5V_LOG : -return YH5151E_PAGE_5V_LOG ; +return YH5151E_PAGE_5V_REAL ;case YH5151E_PAGE_3V3_LOG :return YH5151E_PAGE_3V3_REAL ; }@@ -103,8 +103,18 @@ static int set_page(struct i2c_client *client, int page_log)static int fsp3y_read_byte_data (struct i2c_client *client,int page,int reg) { +const struct pmbus_driver_info *info =pmbus_get_driver_info (client); +struct fsp3y_data *data =to_fsp3y_data (info);int rv; +/* +* YH5151-E outputs vout in linear11. The conversion is done when +* reading. Here, we have to inject pmbus_core with the correct +* exponent (it is -6). +*/ +if (data->chip == yh5151e && reg ==PMBUS_VOUT_MODE ) +return 0x1A ; + rv =set_page (client, page);if (rv <0 )return rv;@@ -114,6 +124,8 @@ static int fsp3y_read_byte_data(struct i2c_client *client, int page, int reg)static int fsp3y_read_word_data (struct i2c_client *client,int page,int phase,int reg) { +const struct pmbus_driver_info *info =pmbus_get_driver_info (client); +struct fsp3y_data *data =to_fsp3y_data (info);int rv;/* @@ -144,7 +156,18 @@ static int fsp3y_read_word_data(struct i2c_client *client, int page, int phase,if (rv <0 )return rv; -return i2c_smbus_read_word_data (client, reg); + rv =i2c_smbus_read_word_data (client, reg); +if (rv <0 ) +return rv; + +/* +* YH-5151E is non-compliant and outputs output voltages in linear11 +* instead of linear16. +*/ +if (data->chip == yh5151e && reg ==PMBUS_READ_VOUT ) + rv =sign_extend32 (rv,10 ) &0xffff ; + +return rv; }struct pmbus_driver_info fsp3y_info[] = {