Skip to contentSkip to conversation

Fix FSP-3Y YH-5151E non-compliant vout encoding

PATCH Superseded Václav Kubernát 2 participants 2 messages Apr 28, 2021 Hardware monitoring

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 Fix FSP-3Y YH-5151E non-compliant vout encoding

I didn't properly test the driver for YH-5151E, so it was completely broken. Firstly, the log/real mapping was incorrect in one case. Secondly, PMBus specifies that output voltages should be in the linear16 encoding. However, the PDU is non-compliant and uses linear11. YM-2151E isn't affected by this. Fix this by converting the values inside the read functions. linear16 gets the exponent from the VOUT_MODE command. The device doesn't support it, so I have to manually supply the value for it.

Both supported devices have now been tested to report correct vout values.

---
 drivers/hwmon/pmbus/fsp-3y.c | 26 ++++++++++++++++++++++++--
 1 file changed, 24 insertions(+), 2 deletions(-)
drivers/hwmon/pmbus/fsp-3y.c +24 -2
index 564649e87e34..dc147a79d6aa 100644
@@ -57,7 +57,7 @@ static int page_log_to_page_real(int page_log, enum chips chip)
 		case YH5151E_PAGE_12V_LOG:
 			return YH5151E_PAGE_12V_REAL;
 		case YH5151E_PAGE_5V_LOG:
-			return YH5151E_PAGE_5V_LOG;
+			return YH5151E_PAGE_5V_REAL;
 		case YH5151E_PAGE_3V3_LOG:
 			return YH5151E_PAGE_3V3_REAL;
 		}
@@ -103,17 +103,28 @@ static int set_page(struct i2c_client *client, int page_log)
 
 static int fsp3y_read_byte_data(struct i2c_client *client, int page, int reg)
 {
+	const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+	struct fsp3y_data *data = to_fsp3y_data(info);
 	int rv;
 
 	rv = set_page(client, page);
 	if (rv < 0)
 		return rv;
 
+	/*
+	 * YH5151-E outputs vout in linear11. The conversion is done later, but
+	 * I have to inject pmbus_core with the correct exponent.
+	 */
+	if (data->chip == yh5151e && reg == PMBUS_VOUT_MODE)
+		return 0x1A;
+
 	return i2c_smbus_read_byte_data(client, reg);
 }
 
 static int fsp3y_read_word_data(struct i2c_client *client, int page, int phase, int reg)
 {
+	const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+	struct fsp3y_data *data = to_fsp3y_data(info);
 	int rv;
 
 	/*
@@ -144,7 +155,18 @@ static int fsp3y_read_word_data(struct i2c_client *client, int page, int phase,
 	if (rv < 0)
 		return rv;
 
-	return i2c_smbus_read_word_data(client, reg);
+	rv = i2c_smbus_read_word_data(client, reg);
+	if (rv < 0)
+		return rv;
+
+	/*
+	 * The PDU is non-compliant and outputs output voltages in linear11
+	 * instead of linear16.
+	 */
+	if (data->chip == yh5151e && reg == PMBUS_READ_VOUT)
+		rv = ((s16)((rv & 0x7ff) << 5)) >> 5;
+
+	return rv;
 }
 
 struct pmbus_driver_info fsp3y_info[] = {
Signature · 1 line
2.31.1
maintainer
#1 lore raw
Quoted 9 lines · Václav Kubernát

I didn't properly test the driver for YH-5151E, so it was completely broken. Firstly, the log/real mapping was incorrect in one case. Secondly, PMBus specifies that output voltages should be in the linear16 encoding. However, the PDU is non-compliant and uses linear11. YM-2151E isn't affected by this. Fix this by converting the values inside the read functions. linear16 gets the exponent from the VOUT_MODE command. The device doesn't support it, so I have to manually supply the value for it.

Quoted 3 lines

Both supported devices have now been tested to report correct vout values.

Fixes 1734b4135a62 ("hwmon: Add driver for fsp-3y PSUs and PDUs")
Quoted 23 lines
---
 drivers/hwmon/pmbus/fsp-3y.c | 26 ++++++++++++++++++++++++--
 1 file changed, 24 insertions(+), 2 deletions(-)
drivers/hwmon/pmbus/fsp-3y.c +2 -1
index 564649e87e34..dc147a79d6aa 100644
@@ -57,7 +57,7 @@ static int page_log_to_page_real(int page_log, enum chips chip)
 		case YH5151E_PAGE_12V_LOG:
 			return YH5151E_PAGE_12V_REAL;
 		case YH5151E_PAGE_5V_LOG:
-			return YH5151E_PAGE_5V_LOG;
+			return YH5151E_PAGE_5V_REAL;
 		case YH5151E_PAGE_3V3_LOG:
 			return YH5151E_PAGE_3V3_REAL;
 		}
@@ -103,17 +103,28 @@ static int set_page(struct i2c_client *client, int page_log)
 
 static int fsp3y_read_byte_data(struct i2c_client *client, int page, int reg)
 {
+	const struct pmbus_driver_info *info = pmbus_get_driver_info(client);

drivers/hwmon/pmbus/fsp-3y.c static int set_page(struct i2c_client *client, int page_log) · line 116

Quoted 10 lines
drivers/hwmon/pmbus/fsp-3y.c +4 -0
+	struct fsp3y_data *data = to_fsp3y_data(info);
 	int rv;
 
 	rv = set_page(client, page);
 	if (rv < 0)
 		return rv;
 
+	/*
+	 * YH5151-E outputs vout in linear11. The conversion is done later, but
+	 * I have to inject pmbus_core with the correct exponent.

s/I/we/

Also, it might be useful to mention the actual exponent (-6 ?) in the comment.

drivers/hwmon/pmbus/fsp-3y.c static int set_page(struct i2c_client *client, int page_log) · line 119

Quoted 3 lines
drivers/hwmon/pmbus/fsp-3y.c +3 -0
+	 */
+	if (data->chip == yh5151e && reg == PMBUS_VOUT_MODE)
+		return 0x1A;

Can this code be moved ahead of set_page() ?

Quoted 12 lines
drivers/hwmon/pmbus/fsp-3y.c +3 -0
+
 	return i2c_smbus_read_byte_data(client, reg);
 }
 
 static int fsp3y_read_word_data(struct i2c_client *client, int page, int phase, int reg)
 {
+	const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+	struct fsp3y_data *data = to_fsp3y_data(info);
 	int rv;
 
 	/*

drivers/hwmon/pmbus/fsp-3y.c static int fsp3y_read_word_data(struct i2c_client *client, int page, int phase, · line 163

Quoted 10 lines
drivers/hwmon/pmbus/fsp-3y.c +6 -1
@@ -144,7 +155,18 @@ static int fsp3y_read_word_data(struct i2c_client *client, int page, int phase,
 	if (rv < 0)
 		return rv;
 
-	return i2c_smbus_read_word_data(client, reg);
+	rv = i2c_smbus_read_word_data(client, reg);
+	if (rv < 0)
+		return rv;
+
+	/*
+	 * The PDU is non-compliant and outputs output voltages in linear11

s/The PDU/YH-5151E/

drivers/hwmon/pmbus/fsp-3y.c static int fsp3y_read_word_data(struct i2c_client *client, int page, int phase, · line 167

Quoted 4 lines
drivers/hwmon/pmbus/fsp-3y.c +4 -0
+	 * instead of linear16.
+	 */
+	if (data->chip == yh5151e && reg == PMBUS_READ_VOUT)
+		rv = ((s16)((rv & 0x7ff) << 5)) >> 5;

Problem with this is that it auto-converts to int and will return a negative value if bit 10 is set (I wrote some test code and confirmed it, just to be sure).

		rv = sign_extend32(rv, 10) & 0xffff;

should work here.

Thanks,
Guenter

Quoted 6 lines
drivers/hwmon/pmbus/fsp-3y.c +2 -0
+
+	return rv;
 }
 
 struct pmbus_driver_info fsp3y_info[] = {