Skip to contentSkip to conversation

4.19.191-rc1 review

PATCH In review Greg Kroah-Hartman 10 participants 439 messages May 20, 2021 – Jun 24, 2021 Page 3 of 3

Subsystems (6)
lore
Share & tools
lore
author maintainer
#331 lore raw

PATCH 331/425 net: ethernet: mtk_eth_soc: fix RX VLAN offload

In reply to Greg Kroah-Hartman

From: Felix Fietkau <[email protected]>

[ Upstream commit 3f57d8c40fea9b20543cab4da12f4680d2ef182c ]

The VLAN ID in the rx descriptor is only valid if the RX_DMA_VTAG bit is set. Fixes frames wrongly marked with VLAN tags.

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 2 +-
 drivers/net/ethernet/mediatek/mtk_eth_soc.h | 1 +
 2 files changed, 2 insertions(+), 1 deletion(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.c +1 -1
index b72a4fad7bc8..59f3dce3ab1d 100644
@@ -1041,7 +1041,7 @@ static int mtk_poll_rx(struct napi_struct *napi, int budget,
 		skb->protocol = eth_type_trans(skb, netdev);
 
 		if (netdev->features & NETIF_F_HW_VLAN_CTAG_RX &&
-		    RX_DMA_VID(trxd.rxd3))
+		    (trxd.rxd2 & RX_DMA_VTAG))
 			__vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q),
 					       RX_DMA_VID(trxd.rxd3));
 		skb_record_rx_queue(skb, 0);
drivers/net/ethernet/mediatek/mtk_eth_soc.h +1 -0
index 46819297fc3e..cb6b27861afa 100644
@@ -285,6 +285,7 @@
 #define RX_DMA_DONE		BIT(31)
 #define RX_DMA_PLEN0(_x)	(((_x) & 0x3fff) << 16)
 #define RX_DMA_GET_PLEN0(_x)	(((_x) >> 16) & 0x3fff)
+#define RX_DMA_VTAG		BIT(15)
 
 /* QDMA descriptor rxd3 */
 #define RX_DMA_VID(_x)		((_x) & 0xfff)
Signature · 1 line
2.30.2
author maintainer
#332 lore raw

PATCH 332/425 ia64: module: fix symbolizer crash on fdescr

In reply to Greg Kroah-Hartman

From: Sergei Trofimovich <[email protected]>

[ Upstream commit 99e729bd40fb3272fa4b0140839d5e957b58588a ]

Noticed failure as a crash on ia64 when tried to symbolize all backtraces collected by page_owner=on:

    $ cat /sys/kernel/debug/page_owner
    <oops>
    CPU: 1 PID: 2074 Comm: cat Not tainted 5.12.0-rc4 #226
    Hardware name: hp server rx3600, BIOS 04.03 04/08/2008
    ip is at dereference_module_function_descriptor+0x41/0x100

Crash happens at dereference_module_function_descriptor() due to use-after-free when dereferencing ".opd" section header.

All section headers are already freed after module is laoded successfully.

To keep symbolizer working the change stores ".opd" address and size after module is relocated to a new place and before section headers are discarded.

To make similar errors less obscure module_finalize() now zeroes out all variables relevant to module loading only.

---
 arch/ia64/include/asm/module.h |  6 +++++-
 arch/ia64/kernel/module.c      | 29 +++++++++++++++++++++++++----
 2 files changed, 30 insertions(+), 5 deletions(-)
arch/ia64/include/asm/module.h +5 -1
index f319144260ce..9fbf32e6e881 100644
@@ -14,16 +14,20 @@
 struct elf64_shdr;			/* forward declration */
 
 struct mod_arch_specific {
+	/* Used only at module load time. */
 	struct elf64_shdr *core_plt;	/* core PLT section */
 	struct elf64_shdr *init_plt;	/* init PLT section */
 	struct elf64_shdr *got;		/* global offset table */
 	struct elf64_shdr *opd;		/* official procedure descriptors */
 	struct elf64_shdr *unwind;	/* unwind-table section */
 	unsigned long gp;		/* global-pointer for module */
+	unsigned int next_got_entry;	/* index of next available got entry */
 
+	/* Used at module run and cleanup time. */
 	void *core_unw_table;		/* core unwind-table cookie returned by unwinder */
 	void *init_unw_table;		/* init unwind-table cookie returned by unwinder */
-	unsigned int next_got_entry;	/* index of next available got entry */
+	void *opd_addr;			/* symbolize uses .opd to get to actual function */
+	unsigned long opd_size;
 };
 
 #define MODULE_PROC_FAMILY	"ia64"
arch/ia64/kernel/module.c +25 -4
index 1a42ba885188..ee693c8cec49 100644
@@ -905,9 +905,31 @@ register_unwind_table (struct module *mod)
 int
 module_finalize (const Elf_Ehdr *hdr, const Elf_Shdr *sechdrs, struct module *mod)
 {
+	struct mod_arch_specific *mas = &mod->arch;
+
 	DEBUGP("%s: init: entry=%p\n", __func__, mod->init);
-	if (mod->arch.unwind)
+	if (mas->unwind)
 		register_unwind_table(mod);
+
+	/*
+	 * ".opd" was already relocated to the final destination. Store
+	 * it's address for use in symbolizer.
+	 */
+	mas->opd_addr = (void *)mas->opd->sh_addr;
+	mas->opd_size = mas->opd->sh_size;
+
+	/*
+	 * Module relocation was already done at this point. Section
+	 * headers are about to be deleted. Wipe out load-time context.
+	 */
+	mas->core_plt = NULL;
+	mas->init_plt = NULL;
+	mas->got = NULL;
+	mas->opd = NULL;
+	mas->unwind = NULL;
+	mas->gp = 0;
+	mas->next_got_entry = 0;
+
 	return 0;
 }
 
@@ -926,10 +948,9 @@ module_arch_cleanup (struct module *mod)
 
 void *dereference_module_function_descriptor(struct module *mod, void *ptr)
 {
-	Elf64_Shdr *opd = mod->arch.opd;
+	struct mod_arch_specific *mas = &mod->arch;
 
-	if (ptr < (void *)opd->sh_addr ||
-			ptr >= (void *)(opd->sh_addr + opd->sh_size))
+	if (ptr < mas->opd_addr || ptr >= mas->opd_addr + mas->opd_size)
 		return ptr;
 
 	return dereference_function_descriptor(ptr);
Signature · 1 line
2.30.2
author maintainer
#333 lore raw

PATCH 333/425 ASoC: rt286: Make RT286_SET_GPIO_* readable and writable

In reply to Greg Kroah-Hartman

From: David Ward <[email protected]>

[ Upstream commit cd8499d5c03ba260e3191e90236d0e5f6b147563 ]

The GPIO configuration cannot be applied if the registers are inaccessible. This prevented the headset mic from working on the Dell XPS 13 9343.

---
 sound/soc/codecs/rt286.c | 3 +++
 1 file changed, 3 insertions(+)
sound/soc/codecs/rt286.c +3 -0
index 7e44ccae3bc8..c29c6cf41ece 100644
@@ -174,6 +174,9 @@ static bool rt286_readable_register(struct device *dev, unsigned int reg)
 	case RT286_PROC_COEF:
 	case RT286_SET_AMP_GAIN_ADC_IN1:
 	case RT286_SET_AMP_GAIN_ADC_IN2:
+	case RT286_SET_GPIO_MASK:
+	case RT286_SET_GPIO_DIRECTION:
+	case RT286_SET_GPIO_DATA:
 	case RT286_SET_POWER(RT286_DAC_OUT1):
 	case RT286_SET_POWER(RT286_DAC_OUT2):
 	case RT286_SET_POWER(RT286_ADC_IN1):
Signature · 1 line
2.30.2
author maintainer
#334 lore raw

PATCH 334/425 f2fs: fix a redundant call to f2fs_balance_fs if an error occurs

In reply to Greg Kroah-Hartman

From: Colin Ian King <[email protected]>

[ Upstream commit 28e18ee636ba28532dbe425540af06245a0bbecb ]

The uninitialized variable dn.node_changed does not get set when a call to f2fs_get_node_page fails. This uninitialized value gets used in the call to f2fs_balance_fs() that may or not may not balances dirty node and dentry pages depending on the uninitialized state of the variable. Fix this by only calling f2fs_balance_fs if err is not set.

Thanks to Jaegeuk Kim for suggesting an appropriate fix.

Addresses-Coverity: ("Uninitialized scalar variable")

Fixes 2a3407607028 ("f2fs: call f2fs_balance_fs only when node was changed")
---
 fs/f2fs/inline.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
fs/f2fs/inline.c +2 -1
index 299f295fcb6c..6bf78cf63ea2 100644
@@ -220,7 +220,8 @@ out:
 
 	f2fs_put_page(page, 1);
 
-	f2fs_balance_fs(sbi, dn.node_changed);
+	if (!err)
+		f2fs_balance_fs(sbi, dn.node_changed);
 
 	return err;
 }
Signature · 1 line
2.30.2
author maintainer
#335 lore raw

PATCH 335/425 PCI: iproc: Fix return value of iproc_msi_irq_domain_alloc()

In reply to Greg Kroah-Hartman

From: Pali Rohár <[email protected]>

[ Upstream commit 1e83130f01b04c16579ed5a5e03d729bcffc4c5d ]

IRQ domain alloc function should return zero on success. Non-zero value indicates failure.

---
 drivers/pci/controller/pcie-iproc-msi.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/pci/controller/pcie-iproc-msi.c +1 -1
index ea612382599c..dc953c73cb56 100644
@@ -271,7 +271,7 @@ static int iproc_msi_irq_domain_alloc(struct irq_domain *domain,
 				    NULL, NULL);
 	}
 
-	return hwirq;
+	return 0;
 }
 
 static void iproc_msi_irq_domain_free(struct irq_domain *domain,
Signature · 1 line
2.30.2
author maintainer
#336 lore raw

PATCH 336/425 PCI: Release OF node in pci_scan_device()s error path

In reply to Greg Kroah-Hartman

From: Dmitry Baryshkov <[email protected]>

[ Upstream commit c99e755a4a4c165cad6effb39faffd0f3377c02d ]

In pci_scan_device(), if pci_setup_device() fails for any reason, the code will not release device's of_node by calling pci_release_of_node(). Fix that by calling the release function.

Fixes 98d9f30c820d ("pci/of: Match PCI devices to OF nodes dynamically")
---
 drivers/pci/probe.c | 1 +
 1 file changed, 1 insertion(+)
drivers/pci/probe.c +1 -0
index 9a5b6a8e2502..113b7bdf86dd 100644
@@ -2359,6 +2359,7 @@ static struct pci_dev *pci_scan_device(struct pci_bus *bus, int devfn)
 	pci_set_of_node(dev);
 
 	if (pci_setup_device(dev)) {
+		pci_release_of_node(dev);
 		pci_bus_put(dev->bus);
 		kfree(dev);
 		return NULL;
Signature · 1 line
2.30.2
author maintainer
#337 lore raw

PATCH 337/425 ARM: 9064/1: hw_breakpoint: Do not directly check the events overflow_handler hook

In reply to Greg Kroah-Hartman

From: Zhen Lei <[email protected]>

[ Upstream commit a506bd5756290821a4314f502b4bafc2afcf5260 ]

The commit 1879445dfa7b ("perf/core: Set event's default ::overflow_handler()") set a default event->overflow_handler in perf_event_alloc(), and replace the check event->overflow_handler with is_default_overflow_handler(), but one is missing.

Currently, the bp->overflow_handler can not be NULL. As a result, enable_single_step() is always not invoked.

Comments from Zhen Lei:

https://patchwork.kernel.org/project/linux-arm-kernel/patch/[email protected]/

Fixes 1879445dfa7b ("perf/core: Set event's default ::overflow_handler()")
Cc Wang Nan <[email protected]>
---
 arch/arm/kernel/hw_breakpoint.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/kernel/hw_breakpoint.c +1 -1
index 97fa9c167757..2ee5b7f5e7ad 100644
@@ -891,7 +891,7 @@ static void breakpoint_handler(unsigned long unknown, struct pt_regs *regs)
 			info->trigger = addr;
 			pr_debug("breakpoint fired: address = 0x%x\n", addr);
 			perf_bp_event(bp, regs);
-			if (!bp->overflow_handler)
+			if (is_default_overflow_handler(bp))
 				enable_single_step(bp, addr);
 			goto unlock;
 		}
Signature · 1 line
2.30.2
author maintainer
#338 lore raw

PATCH 338/425 rpmsg: qcom_glink_native: fix error return code of qcom_glink_rx_data()

In reply to Greg Kroah-Hartman

From: Jia-Ju Bai <[email protected]>

[ Upstream commit 26594c6bbb60c6bc87e3762a86ceece57d164c66 ]

When idr_find() returns NULL to intent, no error return code of qcom_glink_rx_data() is assigned.
To fix this bug, ret is assigned with -ENOENT in this case.

Fixes 64f95f87920d ("rpmsg: glink: Use the local intents when receiving data")
---
 drivers/rpmsg/qcom_glink_native.c | 1 +
 1 file changed, 1 insertion(+)
drivers/rpmsg/qcom_glink_native.c +1 -0
index a755f85686e5..8fa0f0eaaf43 100644
@@ -857,6 +857,7 @@ static int qcom_glink_rx_data(struct qcom_glink *glink, size_t avail)
 			dev_err(glink->dev,
 				"no intent found for channel %s intent %d",
 				channel->name, liid);
+			ret = -ENOENT;
 			goto advance_rx;
 		}
 	}
Signature · 1 line
2.30.2
author maintainer
#339 lore raw

PATCH 339/425 NFSv4.2: Always flush out writes in nfs42_proc_fallocate()

In reply to Greg Kroah-Hartman

From: Trond Myklebust <[email protected]>

[ Upstream commit 99f23783224355e7022ceea9b8d9f62c0fd01bd8 ]

Whether we're allocating or delallocating space, we should flush out the pending writes in order to avoid races with attribute updates.

Fixes 1e564d3dbd68 ("NFSv4.2: Fix a race in nfs42_proc_deallocate()")
---
 fs/nfs/nfs42proc.c | 16 +++++++++-------
 1 file changed, 9 insertions(+), 7 deletions(-)
fs/nfs/nfs42proc.c +9 -7
index 526441de89c1..da7b73ad811f 100644
@@ -59,7 +59,8 @@ static int _nfs42_proc_fallocate(struct rpc_message *msg, struct file *filep,
 static int nfs42_proc_fallocate(struct rpc_message *msg, struct file *filep,
 				loff_t offset, loff_t len)
 {
-	struct nfs_server *server = NFS_SERVER(file_inode(filep));
+	struct inode *inode = file_inode(filep);
+	struct nfs_server *server = NFS_SERVER(inode);
 	struct nfs4_exception exception = { };
 	struct nfs_lock_context *lock;
 	int err;
@@ -68,9 +69,13 @@ static int nfs42_proc_fallocate(struct rpc_message *msg, struct file *filep,
 	if (IS_ERR(lock))
 		return PTR_ERR(lock);
 
-	exception.inode = file_inode(filep);
+	exception.inode = inode;
 	exception.state = lock->open_context->state;
 
+	err = nfs_sync_inode(inode);
+	if (err)
+		goto out;
+
 	do {
 		err = _nfs42_proc_fallocate(msg, filep, lock, offset, len);
 		if (err == -ENOTSUPP) {
@@ -79,7 +84,7 @@ static int nfs42_proc_fallocate(struct rpc_message *msg, struct file *filep,
 		}
 		err = nfs4_handle_exception(server, err, &exception);
 	} while (exception.retry);
-
+out:
 	nfs_put_lock_context(lock);
 	return err;
 }
@@ -117,16 +122,13 @@ int nfs42_proc_deallocate(struct file *filep, loff_t offset, loff_t len)
 		return -EOPNOTSUPP;
 
 	inode_lock(inode);
-	err = nfs_sync_inode(inode);
-	if (err)
-		goto out_unlock;
 
 	err = nfs42_proc_fallocate(&msg, filep, offset, len);
 	if (err == 0)
 		truncate_pagecache_range(inode, offset, (offset + len) -1);
 	if (err == -EOPNOTSUPP)
 		NFS_SERVER(inode)->caps &= ~NFS_CAP_DEALLOCATE;
-out_unlock:
+
 	inode_unlock(inode);
 	return err;
 }
Signature · 1 line
2.30.2
author maintainer
#340 lore raw

PATCH 340/425 NFS: Deal correctly with attribute generation counter overflow

In reply to Greg Kroah-Hartman

From: Trond Myklebust <[email protected]>

[ Upstream commit 9fdbfad1777cb4638f489eeb62d85432010c0031 ]

We need to use unsigned long subtraction and then convert to signed in order to deal correcly with C overflow rules.

Fixes f5062003465c ("NFS: Set an attribute barrier on all updates")
---
 fs/nfs/inode.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
fs/nfs/inode.c +4 -4
index aee66d8f1330..dc55ecc3bec4 100644
@@ -1607,10 +1607,10 @@ EXPORT_SYMBOL_GPL(_nfs_display_fhandle);
  */
 static int nfs_inode_attrs_need_update(const struct inode *inode, const struct nfs_fattr *fattr)
 {
-	const struct nfs_inode *nfsi = NFS_I(inode);
+	unsigned long attr_gencount = NFS_I(inode)->attr_gencount;
 
-	return ((long)fattr->gencount - (long)nfsi->attr_gencount) > 0 ||
-		((long)nfsi->attr_gencount - (long)nfs_read_attr_generation_counter() > 0);
+	return (long)(fattr->gencount - attr_gencount) > 0 ||
+	       (long)(attr_gencount - nfs_read_attr_generation_counter()) > 0;
 }
 
 static int nfs_refresh_inode_locked(struct inode *inode, struct nfs_fattr *fattr)
@@ -2034,7 +2034,7 @@ static int nfs_update_inode(struct inode *inode, struct nfs_fattr *fattr)
 			nfsi->attrtimeo_timestamp = now;
 		}
 		/* Set the barrier to be more recent than this fattr */
-		if ((long)fattr->gencount - (long)nfsi->attr_gencount > 0)
+		if ((long)(fattr->gencount - nfsi->attr_gencount) > 0)
 			nfsi->attr_gencount = fattr->gencount;
 	}
 
Signature · 1 line
2.30.2
author maintainer
#341 lore raw

PATCH 341/425 PCI: endpoint: Fix missing destroy_workqueue()

In reply to Greg Kroah-Hartman

From: Yang Yingliang <[email protected]>

[ Upstream commit acaef7981a218813e3617edb9c01837808de063c ]

Add the missing destroy_workqueue() before return from pci_epf_test_init() in the error handling case and add destroy_workqueue() in pci_epf_test_exit().

Fixes 349e7a85b25fa ("PCI: endpoint: functions: Add an EP function to test PCI")
---
 drivers/pci/endpoint/functions/pci-epf-test.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/pci/endpoint/functions/pci-epf-test.c +3 -0
index 4bbd26e8a9e2..09a1e449cd1c 100644
@@ -572,6 +572,7 @@ static int __init pci_epf_test_init(void)
 					     WQ_MEM_RECLAIM | WQ_HIGHPRI, 0);
 	ret = pci_epf_register_driver(&test_driver);
 	if (ret) {
+		destroy_workqueue(kpcitest_workqueue);
 		pr_err("Failed to register pci epf test driver --> %d\n", ret);
 		return ret;
 	}
@@ -582,6 +583,8 @@ module_init(pci_epf_test_init);
 
 static void __exit pci_epf_test_exit(void)
 {
+	if (kpcitest_workqueue)
+		destroy_workqueue(kpcitest_workqueue);
 	pci_epf_unregister_driver(&test_driver);
 }
 module_exit(pci_epf_test_exit);
Signature · 1 line
2.30.2
author maintainer
#342 lore raw

PATCH 342/425 pNFS/flexfiles: fix incorrect size check in decode_nfs_fh()

In reply to Greg Kroah-Hartman

From: Nikola Livic <[email protected]>

[ Upstream commit ed34695e15aba74f45247f1ee2cf7e09d449f925 ]

We (adam zabrocki, alexander matrosov, alexander tereshkin, maksym bazalii) observed the check:

	if (fh->size > sizeof(struct nfs_fh))

should not use the size of the nfs_fh struct which includes an extra two bytes from the size field.

struct nfs_fh {
	unsigned short         size;
	unsigned char          data[NFS_MAXFHSIZE];
}

but should determine the size from data[NFS_MAXFHSIZE] so the memcpy will not write 2 bytes beyond destination. The proposed fix is to compare against the NFS_MAXFHSIZE directly, as is done elsewhere in fs code base.

Fixes d67ae825a59d ("pnfs/flexfiles: Add the FlexFile Layout Driver")
---
 fs/nfs/flexfilelayout/flexfilelayout.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
fs/nfs/flexfilelayout/flexfilelayout.c +1 -1
index d8cba46a9395..fee421da2197 100644
@@ -101,7 +101,7 @@ static int decode_nfs_fh(struct xdr_stream *xdr, struct nfs_fh *fh)
 	if (unlikely(!p))
 		return -ENOBUFS;
 	fh->size = be32_to_cpup(p++);
-	if (fh->size > sizeof(struct nfs_fh)) {
+	if (fh->size > NFS_MAXFHSIZE) {
 		printk(KERN_ERR "NFS flexfiles: Too big fh received %d\n",
 		       fh->size);
 		return -EOVERFLOW;
Signature · 1 line
2.30.2
author maintainer
#343 lore raw

PATCH 343/425 NFSv4.2 fix handling of sr_eof in SEEKs reply

In reply to Greg Kroah-Hartman

From: Olga Kornievskaia <[email protected]>

[ Upstream commit 73f5c88f521a630ea1628beb9c2d48a2e777a419 ]

Currently the client ignores the value of the sr_eof of the SEEK operation. According to the spec, if the server didn't find the requested extent and reached the end of the file, the server would return sr_eof=true. In case the request for DATA and no data was found (ie in the middle of the hole), then the lseek expects that ENXIO would be returned.

Fixes 1c6dcbe5ceff8 ("NFS: Implement SEEK")
---
 fs/nfs/nfs42proc.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
fs/nfs/nfs42proc.c +4 -1
index da7b73ad811f..be252795a6f7 100644
@@ -500,7 +500,10 @@ static loff_t _nfs42_proc_llseek(struct file *filep,
 	if (status)
 		return status;
 
-	return vfs_setpos(filep, res.sr_offset, inode->i_sb->s_maxbytes);
+	if (whence == SEEK_DATA && res.sr_eof)
+		return -NFS4ERR_NXIO;
+	else
+		return vfs_setpos(filep, res.sr_offset, inode->i_sb->s_maxbytes);
 }
 
 loff_t nfs42_proc_llseek(struct file *filep, loff_t offset, int whence)
Signature · 1 line
2.30.2
author maintainer
#344 lore raw

PATCH 344/425 rtc: ds1307: Fix wday settings for rx8130

In reply to Greg Kroah-Hartman

From: Nobuhiro Iwamatsu <[email protected]>

[ Upstream commit 204756f016726a380bafe619438ed979088bd04a ]

rx8130 wday specifies the bit position, not BCD.

Fixes ee0981be7704 ("rtc: ds1307: Add support for Epson RX8130CE")
---
 drivers/rtc/rtc-ds1307.c | 12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)
drivers/rtc/rtc-ds1307.c +10 -2
index ebd59e86a567..94d31779933f 100644
@@ -434,7 +434,11 @@ static int ds1307_get_time(struct device *dev, struct rtc_time *t)
 	t->tm_min = bcd2bin(regs[DS1307_REG_MIN] & 0x7f);
 	tmp = regs[DS1307_REG_HOUR] & 0x3f;
 	t->tm_hour = bcd2bin(tmp);
-	t->tm_wday = bcd2bin(regs[DS1307_REG_WDAY] & 0x07) - 1;
+	/* rx8130 is bit position, not BCD */
+	if (ds1307->type == rx_8130)
+		t->tm_wday = fls(regs[DS1307_REG_WDAY] & 0x7f);
+	else
+		t->tm_wday = bcd2bin(regs[DS1307_REG_WDAY] & 0x07) - 1;
 	t->tm_mday = bcd2bin(regs[DS1307_REG_MDAY] & 0x3f);
 	tmp = regs[DS1307_REG_MONTH] & 0x1f;
 	t->tm_mon = bcd2bin(tmp) - 1;
@@ -481,7 +485,11 @@ static int ds1307_set_time(struct device *dev, struct rtc_time *t)
 	regs[DS1307_REG_SECS] = bin2bcd(t->tm_sec);
 	regs[DS1307_REG_MIN] = bin2bcd(t->tm_min);
 	regs[DS1307_REG_HOUR] = bin2bcd(t->tm_hour);
-	regs[DS1307_REG_WDAY] = bin2bcd(t->tm_wday + 1);
+	/* rx8130 is bit position, not BCD */
+	if (ds1307->type == rx_8130)
+		regs[DS1307_REG_WDAY] = 1 << t->tm_wday;
+	else
+		regs[DS1307_REG_WDAY] = bin2bcd(t->tm_wday + 1);
 	regs[DS1307_REG_MDAY] = bin2bcd(t->tm_mday);
 	regs[DS1307_REG_MONTH] = bin2bcd(t->tm_mon + 1);
 
Signature · 1 line
2.30.2
author maintainer
#345 lore raw

PATCH 345/425 net: hns3: disable phy loopback setting in hclge_mac_start_phy

In reply to Greg Kroah-Hartman

From: Yufeng Mo <[email protected]>

[ Upstream commit 472497d0bdae890a896013332a0b673f9acdf2bf ]

If selftest and reset are performed at the same time, the phy loopback setting may be still in enable state after the reset, and device cannot link up. So fix this issue by disabling phy loopback before phy_start().

Fixes 256727da7395 ("net: hns3: Add MDIO support to HNS3 Ethernet driver for hip08 SoC")
---
 drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c +2 -0
index 03491e8ebb73..d0fa344f0a84 100644
@@ -235,6 +235,8 @@ void hclge_mac_start_phy(struct hclge_dev *hdev)
 	if (!phydev)
 		return;
 
+	phy_loopback(phydev, false);
+
 	phy_start(phydev);
 }
 
Signature · 1 line
2.30.2
author maintainer
#346 lore raw

PATCH 346/425 sctp: do asoc update earlier in sctp_sf_do_dupcook_a

In reply to Greg Kroah-Hartman

From: Xin Long <[email protected]>

[ Upstream commit 35b4f24415c854cd718ccdf38dbea6297f010aae ]

There's a panic that occurs in a few of envs, the call trace is as below:

[] general protection fault, ... 0x29acd70f1000a: 0000 [#1] SMP PTI [] RIP: 0010:sctp_ulpevent_notify_peer_addr_change+0x4b/0x1fa [sctp]

  []  sctp_assoc_control_transport+0x1b9/0x210 [sctp]
  []  sctp_do_8_2_transport_strike.isra.16+0x15c/0x220 [sctp]
  []  sctp_cmd_interpreter.isra.21+0x1231/0x1a10 [sctp]
  []  sctp_do_sm+0xc3/0x2a0 [sctp]
  []  sctp_generate_timeout_event+0x81/0xf0 [sctp]

This is caused by a transport use-after-free issue. When processing a duplicate COOKIE-ECHO chunk in sctp_sf_do_dupcook_a(), both COOKIE-ACK and SHUTDOWN chunks are allocated with the transort from the new asoc. However, later in the sideeffect machine, the old asoc is used to send them out and old asoc's shutdown_last_sent_to is set to the transport that SHUTDOWN chunk attached to in sctp_cmd_setup_t2(), which actually belongs to the new asoc. After the new_asoc is freed and the old asoc T2 timeout, the old asoc's shutdown_last_sent_to that is already freed would be accessed in sctp_sf_t2_timer_expire().

Thanks Alexander and Jere for helping dig into this issue.

To fix it, this patch is to do the asoc update first, then allocate the COOKIE-ACK and SHUTDOWN chunks with the 'updated' old asoc. This would make more sense, as a chunk from an asoc shouldn't be sent out with another asoc. We had fixed quite a few issues caused by this.

Fixes 145cb2f7177d ("sctp: Fix bundling of SHUTDOWN with COOKIE-ACK")
Reported-by [email protected]
---
 net/sctp/sm_statefuns.c | 25 ++++++++++++++++++++-----
 1 file changed, 20 insertions(+), 5 deletions(-)
net/sctp/sm_statefuns.c +20 -5
index a3033b74df54..882cd5f40a0a 100644
@@ -1856,20 +1856,35 @@ static enum sctp_disposition sctp_sf_do_dupcook_a(
 			SCTP_TO(SCTP_EVENT_TIMEOUT_T4_RTO));
 	sctp_add_cmd_sf(commands, SCTP_CMD_PURGE_ASCONF_QUEUE, SCTP_NULL());
 
-	repl = sctp_make_cookie_ack(new_asoc, chunk);
+	/* Update the content of current association. */
+	if (sctp_assoc_update((struct sctp_association *)asoc, new_asoc)) {
+		struct sctp_chunk *abort;
+
+		abort = sctp_make_abort(asoc, NULL, sizeof(struct sctp_errhdr));
+		if (abort) {
+			sctp_init_cause(abort, SCTP_ERROR_RSRC_LOW, 0);
+			sctp_add_cmd_sf(commands, SCTP_CMD_REPLY, SCTP_CHUNK(abort));
+		}
+		sctp_add_cmd_sf(commands, SCTP_CMD_SET_SK_ERR, SCTP_ERROR(ECONNABORTED));
+		sctp_add_cmd_sf(commands, SCTP_CMD_ASSOC_FAILED,
+				SCTP_PERR(SCTP_ERROR_RSRC_LOW));
+		SCTP_INC_STATS(net, SCTP_MIB_ABORTEDS);
+		SCTP_DEC_STATS(net, SCTP_MIB_CURRESTAB);
+		goto nomem;
+	}
+
+	repl = sctp_make_cookie_ack(asoc, chunk);
 	if (!repl)
 		goto nomem;
 
 	/* Report association restart to upper layer. */
 	ev = sctp_ulpevent_make_assoc_change(asoc, 0, SCTP_RESTART, 0,
-					     new_asoc->c.sinit_num_ostreams,
-					     new_asoc->c.sinit_max_instreams,
+					     asoc->c.sinit_num_ostreams,
+					     asoc->c.sinit_max_instreams,
 					     NULL, GFP_ATOMIC);
 	if (!ev)
 		goto nomem_ev;
 
-	/* Update the content of current association. */
-	sctp_add_cmd_sf(commands, SCTP_CMD_UPDATE_ASSOC, SCTP_ASOC(new_asoc));
 	sctp_add_cmd_sf(commands, SCTP_CMD_EVENT_ULP, SCTP_ULPEVENT(ev));
 	if ((sctp_state(asoc, SHUTDOWN_PENDING) ||
 	     sctp_state(asoc, SHUTDOWN_SENT)) &&
Signature · 1 line
2.30.2
author maintainer
#347 lore raw

PATCH 347/425 ethernet:enic: Fix a use after free bug in enic_hard_start_xmit

In reply to Greg Kroah-Hartman

From: Lv Yunlong <[email protected]>

[ Upstream commit 643001b47adc844ae33510c4bb93c236667008a3 ]

In enic_hard_start_xmit, it calls enic_queue_wq_skb(). Inside enic_queue_wq_skb, if some error happens, the skb will be freed by dev_kfree_skb(skb). But the freed skb is still used in skb_tx_timestamp(skb).

My patch makes enic_queue_wq_skb() return error and goto spin_unlock() incase of error. The solution is provided by Govind.
See https://lkml.org/lkml/2021/4/30/961.

Fixes fb7516d42478e ("enic: add sw timestamp support")
---
 drivers/net/ethernet/cisco/enic/enic_main.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/net/ethernet/cisco/enic/enic_main.c +5 -2
index 810cbe221046..bfe0e820956c 100644
@@ -803,7 +803,7 @@ static inline int enic_queue_wq_skb_encap(struct enic *enic, struct vnic_wq *wq,
 	return err;
 }
 
-static inline void enic_queue_wq_skb(struct enic *enic,
+static inline int enic_queue_wq_skb(struct enic *enic,
 	struct vnic_wq *wq, struct sk_buff *skb)
 {
 	unsigned int mss = skb_shinfo(skb)->gso_size;
@@ -849,6 +849,7 @@ static inline void enic_queue_wq_skb(struct enic *enic,
 		wq->to_use = buf->next;
 		dev_kfree_skb(skb);
 	}
+	return err;
 }
 
 /* netif_tx_lock held, process context with BHs disabled, or BH */
@@ -892,7 +893,8 @@ static netdev_tx_t enic_hard_start_xmit(struct sk_buff *skb,
 		return NETDEV_TX_BUSY;
 	}
 
-	enic_queue_wq_skb(enic, wq, skb);
+	if (enic_queue_wq_skb(enic, wq, skb))
+		goto error;
 
 	if (vnic_wq_desc_avail(wq) < MAX_SKB_FRAGS + ENIC_DESC_MAX_SPLITS)
 		netif_tx_stop_queue(txq);
@@ -900,6 +902,7 @@ static netdev_tx_t enic_hard_start_xmit(struct sk_buff *skb,
 	if (!skb->xmit_more || netif_xmit_stopped(txq))
 		vnic_wq_doorbell(wq);
 
+error:
 	spin_unlock(&enic->wq_lock[txq_map]);
 
 	return NETDEV_TX_OK;
Signature · 1 line
2.30.2
author maintainer
#348 lore raw

PATCH 348/425 sctp: fix a SCTP_MIB_CURRESTAB leak in sctp_sf_do_dupcook_b

In reply to Greg Kroah-Hartman

From: Xin Long <[email protected]>

[ Upstream commit f282df0391267fb2b263da1cc3233aa6fb81defc ]

Normally SCTP_MIB_CURRESTAB is always incremented once asoc enter into ESTABLISHED from the state < ESTABLISHED and decremented when the asoc is being deleted.

However, in sctp_sf_do_dupcook_b(), the asoc's state can be changed to ESTABLISHED from the state >= ESTABLISHED where it shouldn't increment SCTP_MIB_CURRESTAB. Otherwise, one asoc may increment MIB_CURRESTAB multiple times but only decrement once at the end.

I was able to reproduce it by using scapy to do the 4-way shakehands, after that I replayed the COOKIE-ECHO chunk with 'peer_vtag' field changed to different values, and SCTP_MIB_CURRESTAB was incremented multiple times and never went back to 0 even when the asoc was freed.

This patch is to fix it by only incrementing SCTP_MIB_CURRESTAB when the state < ESTABLISHED in sctp_sf_do_dupcook_b().

---
 net/sctp/sm_statefuns.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
net/sctp/sm_statefuns.c +2 -1
index 882cd5f40a0a..be5ea5e8b19e 100644
@@ -1948,7 +1948,8 @@ static enum sctp_disposition sctp_sf_do_dupcook_b(
 	sctp_add_cmd_sf(commands, SCTP_CMD_UPDATE_ASSOC, SCTP_ASOC(new_asoc));
 	sctp_add_cmd_sf(commands, SCTP_CMD_NEW_STATE,
 			SCTP_STATE(SCTP_STATE_ESTABLISHED));
-	SCTP_INC_STATS(net, SCTP_MIB_CURRESTAB);
+	if (asoc->state < SCTP_STATE_ESTABLISHED)
+		SCTP_INC_STATS(net, SCTP_MIB_CURRESTAB);
 	sctp_add_cmd_sf(commands, SCTP_CMD_HB_TIMERS_START, SCTP_NULL());
 
 	repl = sctp_make_cookie_ack(new_asoc, chunk);
Signature · 1 line
2.30.2
author maintainer
#349 lore raw

PATCH 349/425 netfilter: xt_SECMARK: add new revision to fix structure layout

In reply to Greg Kroah-Hartman

From: Pablo Neira Ayuso <[email protected]>

[ Upstream commit c7d13358b6a2f49f81a34aa323a2d0878a0532a2 ]

This extension breaks when trying to delete rules, add a new revision to fix this.

Fixes 5e6874cdb8de ("[SECMARK]: Add xtables SECMARK target")
---
 include/uapi/linux/netfilter/xt_SECMARK.h |  6 ++
 net/netfilter/xt_SECMARK.c                | 88 ++++++++++++++++++-----
 2 files changed, 75 insertions(+), 19 deletions(-)
include/uapi/linux/netfilter/xt_SECMARK.h +6 -0
index 1f2a708413f5..beb2cadba8a9 100644
@@ -20,4 +20,10 @@ struct xt_secmark_target_info {
 	char secctx[SECMARK_SECCTX_MAX];
 };
 
+struct xt_secmark_target_info_v1 {
+	__u8 mode;
+	char secctx[SECMARK_SECCTX_MAX];
+	__u32 secid;
+};
+
 #endif /*_XT_SECMARK_H_target */
net/netfilter/xt_SECMARK.c +69 -19

126 lines not on this page · raw message

Signature · 1 line
2.30.2
author maintainer
#350 lore raw

PATCH 350/425 drm/radeon: Fix off-by-one power_state index heap overwrite

In reply to Greg Kroah-Hartman

From: Kees Cook <[email protected]>

[ Upstream commit 5bbf219328849e83878bddb7c226d8d42e84affc ]

An out of bounds write happens when setting the default power state. KASAN sees this as:

[drm] radeon: 512M of GTT memory ready.
[drm] GART: num cpu pages 131072, num gpu pages 131072
==================================================================

BUG: KASAN: slab-out-of-bounds in
radeon_atombios_parse_power_table_1_3+0x1837/0x1998 [radeon]
Write of size 4 at addr ffff88810178d858 by task systemd-udevd/157

CPU: 0 PID: 157 Comm: systemd-udevd Not tainted 5.12.0-E620 #50
Hardware name: eMachines        eMachines E620  /Nile       , BIOS V1.03 09/30/2008
Call Trace:
 dump_stack+0xa5/0xe6
 print_address_description.constprop.0+0x18/0x239
 kasan_report+0x170/0x1a8
 radeon_atombios_parse_power_table_1_3+0x1837/0x1998 [radeon]
 radeon_atombios_get_power_modes+0x144/0x1888 [radeon]
 radeon_pm_init+0x1019/0x1904 [radeon]
 rs690_init+0x76e/0x84a [radeon]
 radeon_device_init+0x1c1a/0x21e5 [radeon]
 radeon_driver_load_kms+0xf5/0x30b [radeon]
 drm_dev_register+0x255/0x4a0 [drm]
 radeon_pci_probe+0x246/0x2f6 [radeon]
 pci_device_probe+0x1aa/0x294
 really_probe+0x30e/0x850
 driver_probe_device+0xe6/0x135
 device_driver_attach+0xc1/0xf8
 __driver_attach+0x13f/0x146
 bus_for_each_dev+0xfa/0x146
 bus_add_driver+0x2b3/0x447
 driver_register+0x242/0x2c1
 do_one_initcall+0x149/0x2fd
 do_init_module+0x1ae/0x573
 load_module+0x4dee/0x5cca
 __do_sys_finit_module+0xf1/0x140
 do_syscall_64+0x33/0x40
 entry_SYSCALL_64_after_hwframe+0x44/0xae

Without KASAN, this will manifest later when the kernel attempts to allocate memory that was stomped, since it collides with the inline slab freelist pointer:

invalid opcode: 0000 [#1] SMP NOPTI

CPU: 0 PID: 781 Comm: openrc-run.sh Tainted: G        W 5.10.12-gentoo-E620 #2
Hardware name: eMachines        eMachines E620  /Nile , BIOS V1.03       09/30/2008
RIP: 0010:kfree+0x115/0x230
Code: 89 c5 e8 75 ea ff ff 48 8b 00 0f ba e0 09 72 63 e8 1f f4 ff ff 41 89 c4 48 8b 45 00 0f ba e0 10 72 0a 48 8b 45 08 a8 01 75 02 <0f> 0b 44 89 e1 48 c7 c2 00 f0 ff ff be 06 00 00 00 48 d3 e2 48 c7
RSP: 0018:ffffb42f40267e10 EFLAGS: 00010246
RAX: ffffd61280ee8d88 RBX: 0000000000000004 RCX: 000000008010000d
RDX: 4000000000000000 RSI: ffffffffba1360b0 RDI: ffffd61280ee8d80
RBP: ffffd61280ee8d80 R08: ffffffffb91bebdf R09: 0000000000000000
R10: ffff8fe2c1047ac8 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000100
FS:  00007fe80eff6b68(0000) GS:ffff8fe339c00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe80eec7bc0 CR3: 0000000038012000 CR4: 00000000000006f0
Call Trace:
 __free_fdtable+0x16/0x1f
 put_files_struct+0x81/0x9b
 do_exit+0x433/0x94d
 do_group_exit+0xa6/0xa6
 __x64_sys_exit_group+0xf/0xf
 do_syscall_64+0x33/0x40
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fe80ef64bea
Code: Unable to access opcode bytes at RIP 0x7fe80ef64bc0.
RSP: 002b:00007ffdb1c47528 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007fe80ef64bea
RDX: 00007fe80ef64f60 RSI: 0000000000000000 RDI: 0000000000000000
RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000000
R10: 00007fe80ee2c620 R11: 0000000000000246 R12: 00007fe80eff41e0
R13: 00000000ffffffff R14: 0000000000000024 R15: 00007fe80edf9cd0
Modules linked in: radeon(+) ath5k(+) snd_hda_codec_realtek ...

Use a valid power_state index when initializing the "flags" and "misc" and "misc2" fields.

Fixes a48b9b4edb8b ("drm/radeon/kms/pm: add asic specific callbacks for getting power state (v2)")
Fixes 79daedc94281 ("drm/radeon/kms: minor pm cleanups")
---
 drivers/gpu/drm/radeon/radeon_atombios.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/gpu/drm/radeon/radeon_atombios.c +3 -3
index f422a8d6aec4..ffeacaa269e8 100644
@@ -2263,10 +2263,10 @@ static int radeon_atombios_parse_power_table_1_3(struct radeon_device *rdev)
 		rdev->pm.default_power_state_index = state_index - 1;
 		rdev->pm.power_state[state_index - 1].default_clock_mode =
 			&rdev->pm.power_state[state_index - 1].clock_info[0];
-		rdev->pm.power_state[state_index].flags &=
+		rdev->pm.power_state[state_index - 1].flags &=
 			~RADEON_PM_STATE_SINGLE_DISPLAY_ONLY;
-		rdev->pm.power_state[state_index].misc = 0;
-		rdev->pm.power_state[state_index].misc2 = 0;
+		rdev->pm.power_state[state_index - 1].misc = 0;
+		rdev->pm.power_state[state_index - 1].misc2 = 0;
 	}
 	return state_index;
 }
Signature · 1 line
2.30.2
author maintainer
#351 lore raw

PATCH 351/425 drm/radeon: Avoid power table parsing memory leaks

In reply to Greg Kroah-Hartman

From: Kees Cook <[email protected]>

[ Upstream commit c69f27137a38d24301a6b659454a91ad85dff4aa ]

Avoid leaving a hanging pre-allocated clock_info if last mode is invalid, and avoid heap corruption if no valid modes are found.

Fixes 6991b8f2a319 ("drm/radeon/kms: fix segfault in pm rework")
---
 drivers/gpu/drm/radeon/radeon_atombios.c | 20 +++++++++++++++-----
 1 file changed, 15 insertions(+), 5 deletions(-)
drivers/gpu/drm/radeon/radeon_atombios.c +15 -5
index ffeacaa269e8..821b03d6142b 100644
@@ -2133,11 +2133,14 @@ static int radeon_atombios_parse_power_table_1_3(struct radeon_device *rdev)
 		return state_index;
 	/* last mode is usually default, array is low to high */
 	for (i = 0; i < num_modes; i++) {
-		rdev->pm.power_state[state_index].clock_info =
-			kcalloc(1, sizeof(struct radeon_pm_clock_info),
-				GFP_KERNEL);
+		/* avoid memory leaks from invalid modes or unknown frev. */
+		if (!rdev->pm.power_state[state_index].clock_info) {
+			rdev->pm.power_state[state_index].clock_info =
+				kzalloc(sizeof(struct radeon_pm_clock_info),
+					GFP_KERNEL);
+		}
 		if (!rdev->pm.power_state[state_index].clock_info)
-			return state_index;
+			goto out;
 		rdev->pm.power_state[state_index].num_clock_modes = 1;
 		rdev->pm.power_state[state_index].clock_info[0].voltage.type = VOLTAGE_NONE;
 		switch (frev) {
@@ -2256,8 +2259,15 @@ static int radeon_atombios_parse_power_table_1_3(struct radeon_device *rdev)
 			break;
 		}
 	}
+out:
+	/* free any unused clock_info allocation. */
+	if (state_index && state_index < num_modes) {
+		kfree(rdev->pm.power_state[state_index].clock_info);
+		rdev->pm.power_state[state_index].clock_info = NULL;
+	}
+
 	/* last mode is usually default */
-	if (rdev->pm.default_power_state_index == -1) {
+	if (state_index && rdev->pm.default_power_state_index == -1) {
 		rdev->pm.power_state[state_index - 1].type =
 			POWER_STATE_TYPE_DEFAULT;
 		rdev->pm.default_power_state_index = state_index - 1;
Signature · 1 line
2.30.2
author maintainer
#352 lore raw

PATCH 352/425 khugepaged: fix wrong result value for trace_mm_collapse_huge_page_isolate()

In reply to Greg Kroah-Hartman

From: Miaohe Lin <[email protected]>

[ Upstream commit 74e579bf231a337ab3786d59e64bc94f45ca7b3f ]

In writable and !referenced case, the result value should be SCAN_LACK_REFERENCED_PAGE for trace_mm_collapse_huge_page_isolate() instead of default 0 (SCAN_FAIL) here.

Fixes 7d2eba0557c1 ("mm: add tracepoint for scanning pages")
Cc Dan Carpenter <[email protected]>
Cc Ebru Akagunduz <[email protected]>
Cc Mike Kravetz <[email protected]>
Cc Rik van Riel <[email protected]>
---
 mm/khugepaged.c | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)
mm/khugepaged.c +9 -9
index 9c7dc2276156..5dd14ef2e1de 100644
@@ -616,17 +616,17 @@ static int __collapse_huge_page_isolate(struct vm_area_struct *vma,
 		    mmu_notifier_test_young(vma->vm_mm, address))
 			referenced++;
 	}
-	if (likely(writable)) {
-		if (likely(referenced)) {
-			result = SCAN_SUCCEED;
-			trace_mm_collapse_huge_page_isolate(page, none_or_zero,
-							    referenced, writable, result);
-			return 1;
-		}
-	} else {
+
+	if (unlikely(!writable)) {
 		result = SCAN_PAGE_RO;
+	} else if (unlikely(!referenced)) {
+		result = SCAN_LACK_REFERENCED_PAGE;
+	} else {
+		result = SCAN_SUCCEED;
+		trace_mm_collapse_huge_page_isolate(page, none_or_zero,
+						    referenced, writable, result);
+		return 1;
 	}
-
 out:
 	release_pte_pages(pte, _pte);
 	trace_mm_collapse_huge_page_isolate(page, none_or_zero,
Signature · 1 line
2.30.2
author maintainer
#353 lore raw

PATCH 353/425 mm/hugeltb: handle the error case in hugetlb_fix_reserve_counts()

In reply to Greg Kroah-Hartman

From: Miaohe Lin <[email protected]>

[ Upstream commit da56388c4397878a65b74f7fe97760f5aa7d316b ]

A rare out of memory error would prevent removal of the reserve map region for a page. hugetlb_fix_reserve_counts() handles this rare case to avoid dangling with incorrect counts. Unfortunately, hugepage_subpool_get_pages and hugetlb_acct_memory could possibly fail too. We should correctly handle these cases.

Fixes b5cec28d36f5 ("hugetlbfs: truncate_hugepages() takes a range of pages")
Cc Feilong Lin <[email protected]>
Cc Mike Kravetz <[email protected]>
---
 mm/hugetlb.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)
mm/hugetlb.c +9 -2
index f37a821dc5ce..1dfaec50ff93 100644
@@ -588,13 +588,20 @@ void hugetlb_fix_reserve_counts(struct inode *inode)
 {
 	struct hugepage_subpool *spool = subpool_inode(inode);
 	long rsv_adjust;
+	bool reserved = false;
 
 	rsv_adjust = hugepage_subpool_get_pages(spool, 1);
-	if (rsv_adjust) {
+	if (rsv_adjust > 0) {
 		struct hstate *h = hstate_inode(inode);
 
-		hugetlb_acct_memory(h, 1);
+		if (!hugetlb_acct_memory(h, 1))
+			reserved = true;
+	} else if (!rsv_adjust) {
+		reserved = true;
 	}
+
+	if (!reserved)
+		pr_warn("hugetlb: Huge Page Reserved count may go negative.\n");
 }
 
 /*
Signature · 1 line
2.30.2
author maintainer
#354 lore raw

PATCH 354/425 ksm: fix potential missing rmap_item for stable_node

In reply to Greg Kroah-Hartman

From: Miaohe Lin <[email protected]>

[ Upstream commit c89a384e2551c692a9fe60d093fd7080f50afc51 ]

When removing rmap_item from stable tree, STABLE_FLAG of rmap_item is cleared with head reserved. So the following scenario might happen: For ksm page with rmap_item1:

cmp_and_merge_page
stable_node->head = &migrate_nodes; remove_rmap_item_from_tree, but head still equal to stable_node; try_to_merge_with_ksm_page failed;
return;

For the same ksm page with rmap_item2, stable node migration succeed this time. The stable_node->head does not equal to migrate_nodes now. For ksm page with rmap_item1 again:

cmp_and_merge_page
stable_node->head != &migrate_nodes && rmap_item->head == stable_node return;

We would miss the rmap_item for stable_node and might result in failed rmap_walk_ksm(). Fix this by set rmap_item->head to NULL when rmap_item is removed from stable tree.

Fixes 4146d2d673e8 ("ksm: make !merge_across_nodes migration safe")
Cc Hugh Dickins <[email protected]>
---
 mm/ksm.c | 1 +
 1 file changed, 1 insertion(+)
mm/ksm.c +1 -0
index d021bcf94c41..87a541ab1474 100644
@@ -778,6 +778,7 @@ static void remove_rmap_item_from_tree(struct rmap_item *rmap_item)
 		stable_node->rmap_hlist_len--;
 
 		put_anon_vma(rmap_item->anon_vma);
+		rmap_item->head = NULL;
 		rmap_item->address &= PAGE_MASK;
 
 	} else if (rmap_item->address & UNSTABLE_FLAG) {
Signature · 1 line
2.30.2
author maintainer
#355 lore raw

PATCH 355/425 net: fix nla_strcmp to handle more then one trailing null character

In reply to Greg Kroah-Hartman

From: Maciej Żenczykowski <[email protected]>

[ Upstream commit 2c16db6c92b0ee4aa61e88366df82169e83c3f7e ]

Android userspace has been using TCA_KIND with a char[IFNAMESIZ] many-null-terminated buffer containing the string 'bpf'.

This works on 4.19 and ceases to work on 5.10.

I'm not entirely sure what fixes tag to use, but I think the issue was likely introduced in the below mentioned 5.4 commit.

Cc Cong Wang <[email protected]>
Cc David Ahern <[email protected]>
Cc David S. Miller <[email protected]>
Cc Jakub Kicinski <[email protected]>
Cc Jamal Hadi Salim <[email protected]>
Cc Jiri Pirko <[email protected]>
Cc Jiri Pirko <[email protected]>
Fixes 62794fc4fbf5 ("net_sched: add max len check for TCA_KIND")
Change-Id I66dc281f165a2858fc29a44869a270a2d698a82b
---
 lib/nlattr.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
lib/nlattr.c +1 -1
index e335bcafa9e4..00bfc6aece05 100644
@@ -402,7 +402,7 @@ int nla_strcmp(const struct nlattr *nla, const char *str)
 	int attrlen = nla_len(nla);
 	int d;
 
-	if (attrlen > 0 && buf[attrlen - 1] == '\0')
+	while (attrlen > 0 && buf[attrlen - 1] == '\0')
 		attrlen--;
 
 	d = attrlen - len;
Signature · 1 line
2.30.2
author maintainer
#356 lore raw

PATCH 356/425 smc: disallow TCP_ULP in smc_setsockopt()

In reply to Greg Kroah-Hartman

From: Cong Wang <[email protected]>

[ Upstream commit 8621436671f3a4bba5db57482e1ee604708bf1eb ]

syzbot is able to setup kTLS on an SMC socket which coincidentally uses sk_user_data too. Later, kTLS treats it as psock so triggers a refcnt warning. The root cause is that smc_setsockopt() simply calls TCP setsockopt() which includes TCP_ULP. I do not think it makes sense to setup kTLS on top of SMC sockets, so we should just disallow this setup.

It is hard to find a commit to blame, but we can apply this patch since the beginning of TCP_ULP.

Reported-and-tested-by [email protected]
Fixes 734942cc4ea6 ("tcp: ULP infrastructure")
Cc John Fastabend <[email protected]>
---
 net/smc/af_smc.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
net/smc/af_smc.c +3 -1
index 26dcd02b2d0c..9aab4ab8161b 100644
@@ -1644,6 +1644,9 @@ static int smc_setsockopt(struct socket *sock, int level, int optname,
 	struct smc_sock *smc;
 	int val, rc;
 
+	if (level == SOL_TCP && optname == TCP_ULP)
+		return -EOPNOTSUPP;
+
 	smc = smc_sk(sk);
 
 	/* generic setsockopts reaching us here always apply to the
@@ -1665,7 +1668,6 @@ static int smc_setsockopt(struct socket *sock, int level, int optname,
 
 	lock_sock(sk);
 	switch (optname) {
-	case TCP_ULP:
 	case TCP_FASTOPEN:
 	case TCP_FASTOPEN_CONNECT:
 	case TCP_FASTOPEN_KEY:
Signature · 1 line
2.30.2
author maintainer
#357 lore raw

PATCH 357/425 netfilter: nfnetlink_osf: Fix a missing skb_header_pointer() NULL check

In reply to Greg Kroah-Hartman

From: Pablo Neira Ayuso <[email protected]>

[ Upstream commit 5e024c325406470d1165a09c6feaf8ec897936be ]

Do not assume that the tcph->doff field is correct when parsing for TCP options, skb_header_pointer() might fail to fetch these bits.

Fixes 11eeef41d5f6 ("netfilter: passive OS fingerprint xtables match")
---
 net/netfilter/nfnetlink_osf.c | 2 ++
 1 file changed, 2 insertions(+)
net/netfilter/nfnetlink_osf.c +2 -0
index 131f9f8c0b09..917f06110c82 100644
@@ -191,6 +191,8 @@ static const struct tcphdr *nf_osf_hdr_ctx_init(struct nf_osf_hdr_ctx *ctx,
 
 		ctx->optp = skb_header_pointer(skb, ip_hdrlen(skb) +
 				sizeof(struct tcphdr), ctx->optsize, opts);
+		if (!ctx->optp)
+			return NULL;
 	}
 
 	return tcp;
Signature · 1 line
2.30.2
author maintainer
#358 lore raw

PATCH 358/425 sched/fair: Fix unfairness caused by missing load decay

In reply to Greg Kroah-Hartman

From: Odin Ugedal <[email protected]>

[ Upstream commit 0258bdfaff5bd13c4d2383150b7097aecd6b6d82 ]

This fixes an issue where old load on a cfs_rq is not properly decayed, resulting in strange behavior where fairness can decrease drastically. Real workloads with equally weighted control groups have ended up getting a respective 99% and 1%(!!) of cpu time.

When an idle task is attached to a cfs_rq by attaching a pid to a cgroup, the old load of the task is attached to the new cfs_rq and sched_entity by attach_entity_cfs_rq. If the task is then moved to another cpu (and therefore cfs_rq) before being enqueued/woken up, the load will be moved to cfs_rq->removed from the sched_entity. Such a move will happen when enforcing a cpuset on the task (eg. via a cgroup) that force it to move.

The load will however not be removed from the task_group itself, making it look like there is a constant load on that cfs_rq. This causes the vruntime of tasks on other sibling cfs_rq's to increase faster than they are supposed to; causing severe fairness issues. If no other task is started on the given cfs_rq, and due to the cpuset it would not happen, this load would never be properly unloaded. With this patch the load will be properly removed inside update_blocked_averages. This also applies to tasks moved to the fair scheduling class and moved to another cpu, and this path will also fix that. For fork, the entity is queued right away, so this problem does not affect that.

This applies to cases where the new process is the first in the cfs_rq, issue introduced 3d30544f0212 ("sched/fair: Apply more PELT fixes"), and when there has previously been load on the cgroup but the cgroup was removed from the leaflist due to having null PELT load, indroduced in 039ae8bcf7a5 ("sched/fair: Fix O(nr_cgroups) in the load balancing path").

For a simple cgroup hierarchy (as seen below) with two equally weighted groups, that in theory should get 50/50 of cpu time each, it often leads to a load of 60/40 or 70/30.

parent/
cg-1/

    cpu.weight: 100
    cpuset.cpus: 1
  cg-2/
    cpu.weight: 100
    cpuset.cpus: 1

If the hierarchy is deeper (as seen below), while keeping cg-1 and cg-2 equally weighted, they should still get a 50/50 balance of cpu time. This however sometimes results in a balance of 10/90 or 1/99(!!) between the task groups.

$ ps u -C stress
USER         PID %CPU %MEM    VSZ   RSS TTY      STAT START   TIME COMMAND
root       18568  1.1  0.0   3684   100 pts/12   R+   13:36   0:00 stress --cpu 1
root       18580 99.3  0.0   3684   100 pts/12   R+   13:36   0:09 stress --cpu 1

parent/
cg-1/

    cpu.weight: 100
    sub-group/
      cpu.weight: 1
      cpuset.cpus: 1
  cg-2/
    cpu.weight: 100
    sub-group/
      cpu.weight: 10000
      cpuset.cpus: 1

This can be reproduced by attaching an idle process to a cgroup and moving it to a given cpuset before it wakes up. The issue is evident in many (if not most) container runtimes, and has been reproduced with both crun and runc (and therefore docker and all its "derivatives"), and with both cgroup v1 and v2.

Fixes 3d30544f0212 ("sched/fair: Apply more PELT fixes")
Fixes 039ae8bcf7a5 ("sched/fair: Fix O(nr_cgroups) in the load balancing path")
---
 kernel/sched/fair.c | 12 +++++++++---
 1 file changed, 9 insertions(+), 3 deletions(-)
kernel/sched/fair.c +9 -3
index 696d08a4593e..80392cdd5f3b 100644
@@ -9903,16 +9903,22 @@ static void propagate_entity_cfs_rq(struct sched_entity *se)
 {
 	struct cfs_rq *cfs_rq;
 
+	list_add_leaf_cfs_rq(cfs_rq_of(se));
+
 	/* Start to propagate at parent */
 	se = se->parent;
 
 	for_each_sched_entity(se) {
 		cfs_rq = cfs_rq_of(se);
 
-		if (cfs_rq_throttled(cfs_rq))
-			break;
+		if (!cfs_rq_throttled(cfs_rq)){
+			update_load_avg(cfs_rq, se, UPDATE_TG);
+			list_add_leaf_cfs_rq(cfs_rq);
+			continue;
+		}
 
-		update_load_avg(cfs_rq, se, UPDATE_TG);
+		if (list_add_leaf_cfs_rq(cfs_rq))
+			break;
 	}
 }
 #else
Signature · 1 line
2.30.2
author maintainer
#359 lore raw

PATCH 359/425 kernel: kexec_file: fix error return code of kexec_calculate_store_digests()

In reply to Greg Kroah-Hartman

From: Jia-Ju Bai <[email protected]>

[ Upstream commit 31d82c2c787d5cf65fedd35ebbc0c1bd95c1a679 ]

When vzalloc() returns NULL to sha_regions, no error return code of kexec_calculate_store_digests() is assigned. To fix this bug, ret is assigned with -ENOMEM in this case.

---
 kernel/kexec_file.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
kernel/kexec_file.c +3 -1
index 2fbdb78d66c8..89d41c0a10f1 100644
@@ -631,8 +631,10 @@ static int kexec_calculate_store_digests(struct kimage *image)
 
 	sha_region_sz = KEXEC_SEGMENT_MAX * sizeof(struct kexec_sha_region);
 	sha_regions = vzalloc(sha_region_sz);
-	if (!sha_regions)
+	if (!sha_regions) {
+		ret = -ENOMEM;
 		goto out_free_desc;
+	}
 
 	desc->tfm   = tfm;
 	desc->flags = 0;
Signature · 1 line
2.30.2
author maintainer
#360 lore raw

PATCH 360/425 netfilter: nftables: avoid overflows in nft_hash_buckets()

In reply to Greg Kroah-Hartman

From: Eric Dumazet <[email protected]>

[ Upstream commit a54754ec9891830ba548e2010c889e3c8146e449 ]

Number of buckets being stored in 32bit variables, we have to ensure that no overflows occur in nft_hash_buckets()

syzbot injected a size == 0x40000000 and reported:

UBSAN: shift-out-of-bounds in ./include/linux/log2.h:57:13
shift exponent 64 is too large for 64-bit type 'long unsigned int'
CPU: 1 PID: 29539 Comm: syz-executor.4 Not tainted 5.12.0-rc7-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:79 [inline]
 dump_stack+0x141/0x1d7 lib/dump_stack.c:120
 ubsan_epilogue+0xb/0x5a lib/ubsan.c:148
 __ubsan_handle_shift_out_of_bounds.cold+0xb1/0x181 lib/ubsan.c:327
 __roundup_pow_of_two include/linux/log2.h:57 [inline]
 nft_hash_buckets net/netfilter/nft_set_hash.c:411 [inline]
 nft_hash_estimate.cold+0x19/0x1e net/netfilter/nft_set_hash.c:652
 nft_select_set_ops net/netfilter/nf_tables_api.c:3586 [inline]
 nf_tables_newset+0xe62/0x3110 net/netfilter/nf_tables_api.c:4322
 nfnetlink_rcv_batch+0xa09/0x24b0 net/netfilter/nfnetlink.c:488
 nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:612 [inline]
 nfnetlink_rcv+0x3af/0x420 net/netfilter/nfnetlink.c:630
 netlink_unicast_kernel net/netlink/af_netlink.c:1312 [inline]
 netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1338
 netlink_sendmsg+0x856/0xd90 net/netlink/af_netlink.c:1927
 sock_sendmsg_nosec net/socket.c:654 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:674
 ____sys_sendmsg+0x6e8/0x810 net/socket.c:2350
 ___sys_sendmsg+0xf3/0x170 net/socket.c:2404
 __sys_sendmsg+0xe5/0x1b0 net/socket.c:2433
 do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
Fixes 0ed6389c483d ("netfilter: nf_tables: rename set implementations")
---
 net/netfilter/nft_set_hash.c | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)
net/netfilter/nft_set_hash.c +9 -1
index 05118e03c3e4..dbc4ed643b4b 100644
@@ -392,9 +392,17 @@ static void nft_rhash_destroy(const struct nft_set *set)
 				    (void *)set);
 }
 
+/* Number of buckets is stored in u32, so cap our result to 1U<<31 */
+#define NFT_MAX_BUCKETS (1U << 31)
+
 static u32 nft_hash_buckets(u32 size)
 {
-	return roundup_pow_of_two(size * 4 / 3);
+	u64 val = div_u64((u64)size * 4, 3);
+
+	if (val >= NFT_MAX_BUCKETS)
+		return NFT_MAX_BUCKETS;
+
+	return roundup_pow_of_two(val);
 }
 
 static bool nft_rhash_estimate(const struct nft_set_desc *desc, u32 features,
Signature · 1 line
2.30.2
author maintainer
#361 lore raw

PATCH 361/425 i40e: Fix use-after-free in i40e_client_subtask()

In reply to Greg Kroah-Hartman

From: Yunjian Wang <[email protected]>

[ Upstream commit 38318f23a7ef86a8b1862e5e8078c4de121960c3 ]

Currently the call to i40e_client_del_instance frees the object pf->cinst, however pf->cinst->lan_info is being accessed after the free. Fix this by adding the missing return.

Addresses-Coverity: ("Read from pointer after free")

Fixes 7b0b1a6d0ac9 ("i40e: Disable iWARP VSI PETCP_ENA flag on netdev down events")
---
 drivers/net/ethernet/intel/i40e/i40e_client.c | 1 +
 1 file changed, 1 insertion(+)
drivers/net/ethernet/intel/i40e/i40e_client.c +1 -0
index 5f3b8b9ff511..c1832a848714 100644
@@ -377,6 +377,7 @@ void i40e_client_subtask(struct i40e_pf *pf)
 				clear_bit(__I40E_CLIENT_INSTANCE_OPENED,
 					  &cdev->state);
 				i40e_client_del_instance(pf);
+				return;
 			}
 		}
 	}
Signature · 1 line
2.30.2
author maintainer
#362 lore raw

PATCH 362/425 ARC: entry: fix off-by-one error in syscall number validation

In reply to Greg Kroah-Hartman

From: Vineet Gupta <[email protected]>

commit 3433adc8bd09fc9f29b8baddf33b4ecd1ecd2cdc upstream.

We have NR_syscall syscalls from [0 .. NR_syscall-1]. However the check for invalid syscall number is "> NR_syscall" as opposed to >=. This off-by-one error erronesously allows "NR_syscall" to be treated as valid syscall causeing out-of-bounds access into syscall-call table ensuing a crash (holes within syscall table have a invalid-entry handler but this is beyond the array implementing the table).

This problem showed up on v5.6 kernel when testing glibc 2.33 (v5.10 kernel capable, includng faccessat2 syscall 439). The v5.6 kernel has NR_syscalls=439 (0 to 438). Due to the bug, 439 passed by glibc was not handled as -ENOSYS but processed leading to a crash.

---
 arch/arc/kernel/entry.S |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arc/kernel/entry.S +2 -2
@@ -169,7 +169,7 @@ tracesys:
 
 	; Do the Sys Call as we normally would.
 	; Validate the Sys Call number
-	cmp     r8,  NR_syscalls
+	cmp     r8,  NR_syscalls - 1
 	mov.hi  r0, -ENOSYS
 	bhi     tracesys_exit
 
@@ -252,7 +252,7 @@ ENTRY(EV_Trap)
 	;============ Normal syscall case
 
 	; syscall num shd not exceed the total system calls avail
-	cmp     r8,  NR_syscalls
+	cmp     r8,  NR_syscalls - 1
 	mov.hi  r0, -ENOSYS
 	bhi     .Lret_from_system_call
 
author maintainer
#363 lore raw

PATCH 363/425 powerpc/64s: Fix crashes when toggling stf barrier

In reply to Greg Kroah-Hartman

From: Michael Ellerman <[email protected]>

commit 8ec7791bae1327b1c279c5cd6e929c3b12daaf0a upstream.

The STF (store-to-load forwarding) barrier mitigation can be enabled/disabled at runtime via a debugfs file (stf_barrier), which causes the kernel to patch itself to enable/disable the relevant mitigations.

However depending on which mitigation we're using, it may not be safe to do that patching while other CPUs are active. For example the following crash:

User access of kernel address (c00000003fff5af0) - exploit attempt? (uid: 0) segfault (11) at c00000003fff5af0 nip 7fff8ad12198 lr 7fff8ad121f8 code 1
code: 40820128 e93c00d0 e9290058 7c292840 40810058 38600000 4bfd9a81 e8410018
code: 2c030006 41810154 3860ffb6 e9210098 <e94d8ff0> 7d295279 39400000 40820a3c

Shows that we returned to userspace without restoring the user r13 value, due to executing the partially patched STF exit code.

Fix it by doing the patching under stop machine. The CPUs that aren't doing the patching will be spinning in the core of the stop machine logic. That is currently sufficient for our purposes, because none of the patching we do is to that code or anywhere in the vicinity.

Fixes a048a07d7f45 ("powerpc/64s: Add support for a store forwarding barrier at kernel entry/exit")
Cc [email protected] # v4.17+
---
 arch/powerpc/lib/feature-fixups.c |   19 +++++++++++++++++--
 1 file changed, 17 insertions(+), 2 deletions(-)
arch/powerpc/lib/feature-fixups.c +17 -2
@@ -18,6 +18,7 @@
 #include <linux/string.h>
 #include <linux/init.h>
 #include <linux/sched/mm.h>
+#include <linux/stop_machine.h>
 #include <asm/cputable.h>
 #include <asm/code-patching.h>
 #include <asm/page.h>
@@ -225,11 +226,25 @@ void do_stf_exit_barrier_fixups(enum stf
 		                                           : "unknown");
 }
 
+static int __do_stf_barrier_fixups(void *data)
+{
+	enum stf_barrier_type *types = data;
+
+	do_stf_entry_barrier_fixups(*types);
+	do_stf_exit_barrier_fixups(*types);
+
+	return 0;
+}
 
 void do_stf_barrier_fixups(enum stf_barrier_type types)
 {
-	do_stf_entry_barrier_fixups(types);
-	do_stf_exit_barrier_fixups(types);
+	/*
+	 * The call to the fallback entry flush, and the fallback/sync-ori exit
+	 * flush can not be safely patched in/out while other CPUs are executing
+	 * them. So call __do_stf_barrier_fixups() on one CPU while all other CPUs
+	 * spin in the stop machine core with interrupts hard disabled.
+	 */
+	stop_machine(__do_stf_barrier_fixups, &types, NULL);
 }
 
 void do_uaccess_flush_fixups(enum l1d_flush_type types)
author maintainer
#364 lore raw

PATCH 364/425 powerpc/64s: Fix crashes when toggling entry flush barrier

In reply to Greg Kroah-Hartman

From: Michael Ellerman <[email protected]>

commit aec86b052df6541cc97c5fca44e5934cbea4963b upstream.

The entry flush mitigation can be enabled/disabled at runtime via a debugfs file (entry_flush), which causes the kernel to patch itself to enable/disable the relevant mitigations.

However depending on which mitigation we're using, it may not be safe to do that patching while other CPUs are active. For example the following crash:

sleeper[15639]: segfault (11) at c000000000004c20 nip c000000000004c20 lr c000000000004c20

Shows that we returned to userspace with a corrupted LR that points into the kernel, due to executing the partially patched call to the fallback entry flush (ie. we missed the LR restore).

Fix it by doing the patching under stop machine. The CPUs that aren't doing the patching will be spinning in the core of the stop machine logic. That is currently sufficient for our purposes, because none of the patching we do is to that code or anywhere in the vicinity.

Fixes f79643787e0a ("powerpc/64s: flush L1D on kernel entry")
Cc [email protected] # v5.10+
---
 arch/powerpc/lib/feature-fixups.c |   16 +++++++++++++++-
 1 file changed, 15 insertions(+), 1 deletion(-)
arch/powerpc/lib/feature-fixups.c +15 -1
@@ -297,8 +297,9 @@ void do_uaccess_flush_fixups(enum l1d_fl
 						: "unknown");
 }
 
-void do_entry_flush_fixups(enum l1d_flush_type types)
+static int __do_entry_flush_fixups(void *data)
 {
+	enum l1d_flush_type types = *(enum l1d_flush_type *)data;
 	unsigned int instrs[3], *dest;
 	long *start, *end;
 	int i;
@@ -349,6 +350,19 @@ void do_entry_flush_fixups(enum l1d_flus
 							: "ori type" :
 		(types &  L1D_FLUSH_MTTRIG)     ? "mttrig type"
 						: "unknown");
+
+	return 0;
+}
+
+void do_entry_flush_fixups(enum l1d_flush_type types)
+{
+	/*
+	 * The call to the fallback flush can not be safely patched in/out while
+	 * other CPUs are executing it. So call __do_entry_flush_fixups() on one
+	 * CPU while all other CPUs spin in the stop machine core with interrupts
+	 * hard disabled.
+	 */
+	stop_machine(__do_entry_flush_fixups, &types, NULL);
 }
 
 void do_rfi_flush_fixups(enum l1d_flush_type types)
author maintainer
#365 lore raw

PATCH 365/425 hfsplus: prevent corruption in shrinking truncate

In reply to Greg Kroah-Hartman

From: Jouni Roivas <[email protected]>

commit c3187cf32216313fb316084efac4dab3a8459b1d upstream.

I believe there are some issues introduced by commit 31651c607151 ("hfsplus: avoid deadlock on file truncation")

HFS+ has extent records which always contains 8 extents. In case the first extent record in catalog file gets full, new ones are allocated from extents overflow file.

In case shrinking truncate happens to middle of an extent record which locates in extents overflow file, the logic in hfsplus_file_truncate() was changed so that call to hfs_brec_remove() is not guarded any more.

Right action would be just freeing the extents that exceed the new size inside extent record by calling hfsplus_free_extents(), and then check if the whole extent record should be removed. However since the guard (blk_cnt > start) is now after the call to hfs_brec_remove(), this has unfortunate effect that the last matching extent record is removed unconditionally.

To reproduce this issue, create a file which has at least 10 extents, and then perform shrinking truncate into middle of the last extent record, so that the number of remaining extents is not under or divisible by 8. This causes the last extent record (8 extents) to be removed totally instead of truncating into middle of it. Thus this causes corruption, and lost data.

Fix for this is simply checking if the new truncated end is below the start of this extent record, making it safe to remove the full extent record. However call to hfs_brec_remove() can't be moved to it's previous place since we're dropping ->tree_lock and it can cause a race condition and the cached info being invalidated possibly corrupting the node data.

Another issue is related to this one. When entering into the block (blk_cnt > start) we are not holding the ->tree_lock. We break out from the loop not holding the lock, but hfs_find_exit() does unlock it. Not sure if it's possible for someone else to take the lock under our feet, but it can cause hard to debug errors and premature unlocking. Even if there's no real risk of it, the locking should still always be kept in balance. Thus taking the lock now just before the check.

Fixes 31651c607151f ("hfsplus: avoid deadlock on file truncation")
Cc Anatoly Trosinenko <[email protected]>
Cc Viacheslav Dubeyko <[email protected]>
---
 fs/hfsplus/extents.c |    7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
fs/hfsplus/extents.c +4 -3
@@ -598,13 +598,15 @@ void hfsplus_file_truncate(struct inode
 		res = __hfsplus_ext_cache_extent(&fd, inode, alloc_cnt);
 		if (res)
 			break;
-		hfs_brec_remove(&fd);
 
-		mutex_unlock(&fd.tree->tree_lock);
 		start = hip->cached_start;
+		if (blk_cnt <= start)
+			hfs_brec_remove(&fd);
+		mutex_unlock(&fd.tree->tree_lock);
 		hfsplus_free_extents(sb, hip->cached_extents,
 				     alloc_cnt - start, alloc_cnt - blk_cnt);
 		hfsplus_dump_extent(hip->cached_extents);
+		mutex_lock(&fd.tree->tree_lock);
 		if (blk_cnt > start) {
 			hip->extent_state |= HFSPLUS_EXT_DIRTY;
 			break;
@@ -612,7 +614,6 @@ void hfsplus_file_truncate(struct inode
 		alloc_cnt = start;
 		hip->cached_start = hip->cached_blocks = 0;
 		hip->extent_state &= ~(HFSPLUS_EXT_DIRTY | HFSPLUS_EXT_NEW);
-		mutex_lock(&fd.tree->tree_lock);
 	}
 	hfs_find_exit(&fd);
 
author maintainer
#366 lore raw

PATCH 366/425 squashfs: fix divide error in calculate_skip()

In reply to Greg Kroah-Hartman

From: Phillip Lougher <[email protected]>

commit d6e621de1fceb3b098ebf435ef7ea91ec4838a1a upstream.

Sysbot has reported a "divide error" which has been identified as being caused by a corrupted file_size value within the file inode. This value has been corrupted to a much larger value than expected.

Calculate_skip() is passed i_size_read(inode) >> msblk->block_log. Due to the file_size value corruption this overflows the int argument/variable in that function, leading to the divide error.

This patch changes the function to use u64. This will accommodate any unexpectedly large values due to corruption.

The value returned from calculate_skip() is clamped to be never more than SQUASHFS_CACHED_BLKS - 1, or 7. So file_size corruption does not lead to an unexpectedly large return result here.

---
 fs/squashfs/file.c |    6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
fs/squashfs/file.c +3 -3
@@ -224,11 +224,11 @@ failure:
  * If the skip factor is limited in this way then the file will use multiple
  * slots.
  */
-static inline int calculate_skip(int blocks)
+static inline int calculate_skip(u64 blocks)
 {
-	int skip = blocks / ((SQUASHFS_META_ENTRIES + 1)
+	u64 skip = blocks / ((SQUASHFS_META_ENTRIES + 1)
 		 * SQUASHFS_META_INDEXES);
-	return min(SQUASHFS_CACHED_BLKS - 1, skip + 1);
+	return min((u64) SQUASHFS_CACHED_BLKS - 1, skip + 1);
 }
 
 
author maintainer
#367 lore raw

PATCH 367/425 userfaultfd: release page in error path to avoid BUG_ON

In reply to Greg Kroah-Hartman

From: Axel Rasmussen <[email protected]>

commit 7ed9d238c7dbb1fdb63ad96a6184985151b0171c upstream.

Consider the following sequence of events:

1. Userspace issues a UFFD ioctl, which ends up calling into shmem_mfill_atomic_pte(). We successfully account the blocks, we shmem_alloc_page(), but then the copy_from_user() fails. We return -ENOENT. We don't release the page we allocated.
2. Our caller detects this error code, tries the copy_from_user() after dropping the mmap_lock, and retries, calling back into shmem_mfill_atomic_pte().
3. Meanwhile, let's say another process filled up the tmpfs being used.
4. So shmem_mfill_atomic_pte() fails to account blocks this time, and immediately returns - without releasing the page.

This triggers a BUG_ON in our caller, which asserts that the page should always be consumed, unless -ENOENT is returned.

To fix this, detect if we have such a "dangling" page when accounting fails, and if so, release it before returning.

---
 mm/shmem.c |   12 +++++++++++-
 1 file changed, 11 insertions(+), 1 deletion(-)
mm/shmem.c +11 -1
@@ -2271,8 +2271,18 @@ static int shmem_mfill_atomic_pte(struct
 	pgoff_t offset, max_off;
 
 	ret = -ENOMEM;
-	if (!shmem_inode_acct_block(inode, 1))
+	if (!shmem_inode_acct_block(inode, 1)) {
+		/*
+		 * We may have got a page, returned -ENOENT triggering a retry,
+		 * and now we find ourselves with -ENOMEM. Release the page, to
+		 * avoid a BUG_ON in our caller.
+		 */
+		if (unlikely(*pagep)) {
+			put_page(*pagep);
+			*pagep = NULL;
+		}
 		goto out;
+	}
 
 	if (!*pagep) {
 		page = shmem_alloc_page(gfp, info, pgoff);
author maintainer
#368 lore raw

PATCH 368/425 drm/radeon/dpm: Disable sclk switching on Oland when two 4K 60Hz monitors are connected

In reply to Greg Kroah-Hartman

From: Kai-Heng Feng <[email protected]>

commit 227545b9a08c68778ddd89428f99c351fc9315ac upstream.

Screen flickers rapidly when two 4K 60Hz monitors are in use. This issue doesn't happen when one monitor is 4K 60Hz (pixelclock 594MHz) and another one is 4K 30Hz (pixelclock 297MHz).

The issue is gone after setting "power_dpm_force_performance_level" to "high". Following the indication, we found that the issue occurs when sclk is too low.

So resolve the issue by disabling sclk switching when there are two monitors requires high pixelclock (> 297MHz).

v2:
- Only apply the fix to Oland.

---
 drivers/gpu/drm/radeon/radeon.h    |    1 +
 drivers/gpu/drm/radeon/radeon_pm.c |    8 ++++++++
 drivers/gpu/drm/radeon/si_dpm.c    |    3 +++
 3 files changed, 12 insertions(+)
drivers/gpu/drm/radeon/radeon.h +1 -0
@@ -1558,6 +1558,7 @@ struct radeon_dpm {
 	void                    *priv;
 	u32			new_active_crtcs;
 	int			new_active_crtc_count;
+	int			high_pixelclock_count;
 	u32			current_active_crtcs;
 	int			current_active_crtc_count;
 	bool single_display;
drivers/gpu/drm/radeon/radeon_pm.c +8 -0
@@ -1715,6 +1715,7 @@ static void radeon_pm_compute_clocks_dpm
 	struct drm_device *ddev = rdev->ddev;
 	struct drm_crtc *crtc;
 	struct radeon_crtc *radeon_crtc;
+	struct radeon_connector *radeon_connector;
 
 	if (!rdev->pm.dpm_enabled)
 		return;
@@ -1724,6 +1725,7 @@ static void radeon_pm_compute_clocks_dpm
 	/* update active crtc counts */
 	rdev->pm.dpm.new_active_crtcs = 0;
 	rdev->pm.dpm.new_active_crtc_count = 0;
+	rdev->pm.dpm.high_pixelclock_count = 0;
 	if (rdev->num_crtc && rdev->mode_info.mode_config_initialized) {
 		list_for_each_entry(crtc,
 				    &ddev->mode_config.crtc_list, head) {
@@ -1731,6 +1733,12 @@ static void radeon_pm_compute_clocks_dpm
 			if (crtc->enabled) {
 				rdev->pm.dpm.new_active_crtcs |= (1 << radeon_crtc->crtc_id);
 				rdev->pm.dpm.new_active_crtc_count++;
+				if (!radeon_crtc->connector)
+					continue;
+
+				radeon_connector = to_radeon_connector(radeon_crtc->connector);
+				if (radeon_connector->pixelclock_for_modeset > 297000)
+					rdev->pm.dpm.high_pixelclock_count++;
 			}
 		}
 	}
drivers/gpu/drm/radeon/si_dpm.c +3 -0
@@ -3000,6 +3000,9 @@ static void si_apply_state_adjust_rules(
 		    (rdev->pdev->device == 0x6605)) {
 			max_sclk = 75000;
 		}
+
+		if (rdev->pm.dpm.high_pixelclock_count > 1)
+			disable_sclk_switching = true;
 	}
 
 	if (rps->vce_active) {
author maintainer
#369 lore raw

PATCH 369/425 iio: proximity: pulsedlight: Fix rumtime PM imbalance on error

In reply to Greg Kroah-Hartman

From: Dinghao Liu <[email protected]>

[ Upstream commit a2fa9242e89f27696515699fe0f0296bf1ac1815 ]

When lidar_write_control() fails, a pairing PM usage counter decrement is needed to keep the counter balanced.

Fixes 4ac4e086fd8c5 ("iio: pulsedlight-lidar-lite: add runtime PM")
---
 drivers/iio/proximity/pulsedlight-lidar-lite-v2.c | 1 +
 1 file changed, 1 insertion(+)
drivers/iio/proximity/pulsedlight-lidar-lite-v2.c +1 -0
index 47af54f14756..67f85268b63d 100644
@@ -158,6 +158,7 @@ static int lidar_get_measurement(struct lidar_data *data, u16 *reg)
 	ret = lidar_write_control(data, LIDAR_REG_CONTROL_ACQUIRE);
 	if (ret < 0) {
 		dev_err(&client->dev, "cannot send start measurement command");
+		pm_runtime_put_noidle(&client->dev);
 		return ret;
 	}
 
Signature · 1 line
2.30.2
author maintainer
#370 lore raw

PATCH 370/425 usb: fotg210-hcd: Fix an error message

In reply to Greg Kroah-Hartman

From: Christophe JAILLET <[email protected]>

[ Upstream commit a60a34366e0d09ca002c966dd7c43a68c28b1f82 ]

'retval' is known to be -ENODEV here.
This is a hard-coded default error code which is not useful in the error message. Moreover, another error message is printed at the end of the error handling path. The corresponding error code (-ENOMEM) is more informative.

So remove simplify the first error message.

While at it, also remove the useless initialization of 'retval'.

---
 drivers/usb/host/fotg210-hcd.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/usb/host/fotg210-hcd.c +2 -2
index 2d5a72c15069..226b38274a6e 100644
@@ -5569,7 +5569,7 @@ static int fotg210_hcd_probe(struct platform_device *pdev)
 	struct usb_hcd *hcd;
 	struct resource *res;
 	int irq;
-	int retval = -ENODEV;
+	int retval;
 	struct fotg210_hcd *fotg210;
 
 	if (usb_disabled())
@@ -5589,7 +5589,7 @@ static int fotg210_hcd_probe(struct platform_device *pdev)
 	hcd = usb_create_hcd(&fotg210_fotg210_hc_driver, dev,
 			dev_name(dev));
 	if (!hcd) {
-		dev_err(dev, "failed to create hcd with err %d\n", retval);
+		dev_err(dev, "failed to create hcd\n");
 		retval = -ENOMEM;
 		goto fail_create_hcd;
 	}
Signature · 1 line
2.30.2
author maintainer
#371 lore raw

PATCH 371/425 ACPI: scan: Fix a memory leak in an error handling path

In reply to Greg Kroah-Hartman

From: Christophe JAILLET <[email protected]>

[ Upstream commit 0c8bd174f0fc131bc9dfab35cd8784f59045da87 ]

If 'acpi_device_set_name()' fails, we must free 'acpi_device_bus_id->bus_id' or there is a (potential) memory leak.

Fixes eb50aaf960e3 ("ACPI: scan: Use unique number for instance_no")
---
 drivers/acpi/scan.c | 1 +
 1 file changed, 1 insertion(+)
drivers/acpi/scan.c +1 -0
index d3c551bdc2da..1e7e2c438acf 100644
@@ -705,6 +705,7 @@ int acpi_device_add(struct acpi_device *device,
 
 		result = acpi_device_set_name(device, acpi_device_bus_id);
 		if (result) {
+			kfree_const(acpi_device_bus_id->bus_id);
 			kfree(acpi_device_bus_id);
 			goto err_unlock;
 		}
Signature · 1 line
2.30.2
author maintainer
#372 lore raw

PATCH 372/425 blk-mq: Swap two calls in blk_mq_exit_queue()

In reply to Greg Kroah-Hartman

From: Bart Van Assche <[email protected]>

[ Upstream commit 630ef623ed26c18a457cdc070cf24014e50129c2 ]

If a tag set is shared across request queues (e.g. SCSI LUNs) then the block layer core keeps track of the number of active request queues in tags->active_queues. blk_mq_tag_busy() and blk_mq_tag_idle() update that atomic counter if the hctx flag BLK_MQ_F_TAG_QUEUE_SHARED is set. Make sure that blk_mq_exit_queue() calls blk_mq_tag_idle() before that flag is cleared by blk_mq_del_queue_tag_set().

Cc Christoph Hellwig <[email protected]>
Cc Ming Lei <[email protected]>
Cc Hannes Reinecke <[email protected]>
Fixes 0d2602ca30e4 ("blk-mq: improve support for shared tags maps")
---
 block/blk-mq.c |    6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
block/blk-mq.c +4 -2
@@ -2673,10 +2673,12 @@ EXPORT_SYMBOL(blk_mq_init_allocated_queu
 /* tags can _not_ be used after returning from blk_mq_exit_queue */
 void blk_mq_exit_queue(struct request_queue *q)
 {
-	struct blk_mq_tag_set	*set = q->tag_set;
+	struct blk_mq_tag_set *set = q->tag_set;
 
-	blk_mq_del_queue_tag_set(q);
+	/* Checks hctx->flags & BLK_MQ_F_TAG_QUEUE_SHARED. */
 	blk_mq_exit_hw_queues(q, set, set->nr_hw_queues);
+	/* May clear BLK_MQ_F_TAG_QUEUE_SHARED in hctx->flags. */
+	blk_mq_del_queue_tag_set(q);
 }
 
 /* Basically redo blk_mq_init_queue with queue frozen */
author maintainer
#373 lore raw

PATCH 373/425 usb: dwc3: omap: improve extcon initialization

In reply to Greg Kroah-Hartman

From: Marcel Hamer <[email protected]>

commit e17b02d4970913233d543c79c9c66e72cac05bdd upstream.

When extcon is used in combination with dwc3, it is assumed that the dwc3 registers are untouched and as such are only configured if VBUS is valid or ID is tied to ground.

In case VBUS is not valid or ID is floating, the registers are not configured as such during driver initialization, causing a wrong default state during boot.

If the registers are not in a default state, because they are for instance touched by a boot loader, this can cause for a kernel error.

---
 drivers/usb/dwc3/dwc3-omap.c |    5 +++++
 1 file changed, 5 insertions(+)
drivers/usb/dwc3/dwc3-omap.c +5 -0
@@ -432,8 +432,13 @@ static int dwc3_omap_extcon_register(str
 
 		if (extcon_get_state(edev, EXTCON_USB) == true)
 			dwc3_omap_set_mailbox(omap, OMAP_DWC3_VBUS_VALID);
+		else
+			dwc3_omap_set_mailbox(omap, OMAP_DWC3_VBUS_OFF);
+
 		if (extcon_get_state(edev, EXTCON_USB_HOST) == true)
 			dwc3_omap_set_mailbox(omap, OMAP_DWC3_ID_GROUND);
+		else
+			dwc3_omap_set_mailbox(omap, OMAP_DWC3_ID_FLOAT);
 
 		omap->edev = edev;
 	}
author maintainer
#374 lore raw

PATCH 374/425 usb: dwc3: pci: Enable usb2-gadget-lpm-disable for Intel Merrifield

In reply to Greg Kroah-Hartman

From: Ferry Toth <[email protected]>

commit 04357fafea9c7ed34525eb9680c760245c3bb958 upstream.

On Intel Merrifield LPM is causing host to reset port after a timeout. By disabling LPM entirely this is prevented.

Fixes 066c09593454 ("usb: dwc3: pci: Enable extcon driver for Intel Merrifield")
Cc stable <[email protected]>
---
 drivers/usb/dwc3/dwc3-pci.c |    1 +
 1 file changed, 1 insertion(+)
drivers/usb/dwc3/dwc3-pci.c +1 -0
@@ -133,6 +133,7 @@ static const struct property_entry dwc3_
 	PROPERTY_ENTRY_BOOL("snps,disable_scramble_quirk"),
 	PROPERTY_ENTRY_BOOL("snps,dis_u3_susphy_quirk"),
 	PROPERTY_ENTRY_BOOL("snps,dis_u2_susphy_quirk"),
+	PROPERTY_ENTRY_BOOL("snps,usb2-gadget-lpm-disable"),
 	PROPERTY_ENTRY_BOOL("linux,sysdev_is_parent"),
 	{}
 };
author maintainer
#375 lore raw

PATCH 375/425 usb: xhci: Increase timeout for HC halt

In reply to Greg Kroah-Hartman

From: Maximilian Luz <[email protected]>

commit ca09b1bea63ab83f4cca3a2ae8bc4f597ec28851 upstream.

On some devices (specifically the SC8180x based Surface Pro X with QCOM04A6) HC halt / xhci_halt() times out during boot. Manually binding the xhci-hcd driver at some point later does not exhibit this behavior. To work around this, double XHCI_MAX_HALT_USEC, which also resolves this issue.

---
 drivers/usb/host/xhci-ext-caps.h |    5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/usb/host/xhci-ext-caps.h +3 -2
@@ -7,8 +7,9 @@
  * Author: Sarah Sharp
  * Some code borrowed from the Linux EHCI driver.
  */
-/* Up to 16 ms to halt an HC */
-#define XHCI_MAX_HALT_USEC	(16*1000)
+
+/* HC should halt within 16 ms, but use 32 ms as some hosts take longer */
+#define XHCI_MAX_HALT_USEC	(32 * 1000)
 /* HC not running - set to 1 when run/stop bit is cleared. */
 #define XHCI_STS_HALT		(1<<0)
 
author maintainer
#376 lore raw

PATCH 376/425 usb: dwc2: Fix gadget DMA unmap direction

In reply to Greg Kroah-Hartman

From: Phil Elwell <[email protected]>

commit 75a41ce46bae6cbe7d3bb2584eb844291d642874 upstream.

The dwc2 gadget support maps and unmaps DMA buffers as necessary. When mapping and unmapping it uses the direction of the endpoint to select the direction of the DMA transfer, but this fails for Control OUT transfers because the unmap occurs after the endpoint direction has been reversed for the status phase.

A possible solution would be to unmap the buffer before the direction is changed, but a safer, less invasive fix is to remember the buffer direction independently of the endpoint direction.

Fixes fe0b94abcdf6 ("usb: dwc2: gadget: manage ep0 state in software")
Cc stable <[email protected]>
---
 drivers/usb/dwc2/core.h   |    2 ++
 drivers/usb/dwc2/gadget.c |    3 ++-
 2 files changed, 4 insertions(+), 1 deletion(-)
drivers/usb/dwc2/core.h +2 -0
@@ -112,6 +112,7 @@ struct dwc2_hsotg_req;
  * @debugfs: File entry for debugfs file for this endpoint.
  * @dir_in: Set to true if this endpoint is of the IN direction, which
  *          means that it is sending data to the Host.
+ * @map_dir: Set to the value of dir_in when the DMA buffer is mapped.
  * @index: The index for the endpoint registers.
  * @mc: Multi Count - number of transactions per microframe
  * @interval: Interval for periodic endpoints, in frames or microframes.
@@ -161,6 +162,7 @@ struct dwc2_hsotg_ep {
 	unsigned short		fifo_index;
 
 	unsigned char           dir_in;
+	unsigned char           map_dir;
 	unsigned char           index;
 	unsigned char           mc;
 	u16                     interval;
drivers/usb/dwc2/gadget.c +2 -1
@@ -380,7 +380,7 @@ static void dwc2_hsotg_unmap_dma(struct
 {
 	struct usb_request *req = &hs_req->req;
 
-	usb_gadget_unmap_request(&hsotg->gadget, req, hs_ep->dir_in);
+	usb_gadget_unmap_request(&hsotg->gadget, req, hs_ep->map_dir);
 }
 
 /*
@@ -1163,6 +1163,7 @@ static int dwc2_hsotg_map_dma(struct dwc
 {
 	int ret;
 
+	hs_ep->map_dir = hs_ep->dir_in;
 	ret = usb_gadget_map_request(&hsotg->gadget, req, hs_ep->dir_in);
 	if (ret)
 		goto dma_error;
author maintainer
#377 lore raw

PATCH 377/425 usb: core: hub: fix race condition about TRSMRCY of resume

In reply to Greg Kroah-Hartman

From: Chunfeng Yun <[email protected]>

commit 975f94c7d6c306b833628baa9aec3f79db1eb3a1 upstream.

This may happen if the port becomes resume status exactly when usb_port_resume() gets port status, it still need provide a TRSMCRY time before access the device.

---
 drivers/usb/core/hub.c |    6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/usb/core/hub.c +3 -3
@@ -3539,9 +3539,6 @@ int usb_port_resume(struct usb_device *u
 		 * sequence.
 		 */
 		status = hub_port_status(hub, port1, &portstatus, &portchange);
-
-		/* TRSMRCY = 10 msec */
-		msleep(10);
 	}
 
  SuspendCleared:
@@ -3556,6 +3553,9 @@ int usb_port_resume(struct usb_device *u
 				usb_clear_port_feature(hub->hdev, port1,
 						USB_PORT_FEAT_C_SUSPEND);
 		}
+
+		/* TRSMRCY = 10 msec */
+		msleep(10);
 	}
 
 	if (udev->persist_enabled)
author maintainer
#378 lore raw

PATCH 378/425 usb: dwc3: gadget: Return success always for kick transfer in ep queue

In reply to Greg Kroah-Hartman

From: Wesley Cheng <[email protected]>

commit 18ffa988dbae69cc6e9949cddd9606f6fe533894 upstream.

If an error is received when issuing a start or update transfer command, the error handler will stop all active requests (including the current USB request), and call dwc3_gadget_giveback() to notify function drivers of the requests which have been stopped. Avoid returning an error for kick transfer during EP queue, to remove duplicate cleanup operations on the request being queued.

Fixes 8d99087c2db8 ("usb: dwc3: gadget: Properly handle failed kick_transfer")
---
 drivers/usb/dwc3/gadget.c |    4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/usb/dwc3/gadget.c +3 -1
@@ -1413,7 +1413,9 @@ static int __dwc3_gadget_ep_queue(struct
 		}
 	}
 
-	return __dwc3_gadget_kick_transfer(dep);
+	__dwc3_gadget_kick_transfer(dep);
+
+	return 0;
 }
 
 static int dwc3_gadget_ep_queue(struct usb_ep *ep, struct usb_request *request,
author maintainer
#379 lore raw

PATCH 379/425 xhci: Do not use GFP_KERNEL in (potentially) atomic context

In reply to Greg Kroah-Hartman

From: Christophe JAILLET <[email protected]>

commit dda32c00c9a0fa103b5d54ef72c477b7aa993679 upstream.

'xhci_urb_enqueue()' is passed a 'mem_flags' argument, because "URBs may be submitted in interrupt context" (see comment related to 'usb_submit_urb()' in 'drivers/usb/core/urb.c')

So this flag should be used in all the calling chain. Up to now, 'xhci_check_maxpacket()' which is only called from 'xhci_urb_enqueue()', uses GFP_KERNEL.

Be safe and pass the mem_flags to this function as well.

Fixes ddba5cd0aeff ("xhci: Use command structures when queuing commands on the command ring")
---
 drivers/usb/host/xhci.c |    6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/usb/host/xhci.c +3 -3
@@ -1374,7 +1374,7 @@ static int xhci_configure_endpoint(struc
  * we need to issue an evaluate context command and wait on it.
  */
 static int xhci_check_maxpacket(struct xhci_hcd *xhci, unsigned int slot_id,
-		unsigned int ep_index, struct urb *urb)
+		unsigned int ep_index, struct urb *urb, gfp_t mem_flags)
 {
 	struct xhci_container_ctx *out_ctx;
 	struct xhci_input_control_ctx *ctrl_ctx;
@@ -1405,7 +1405,7 @@ static int xhci_check_maxpacket(struct x
 		 * changes max packet sizes.
 		 */
 
-		command = xhci_alloc_command(xhci, true, GFP_KERNEL);
+		command = xhci_alloc_command(xhci, true, mem_flags);
 		if (!command)
 			return -ENOMEM;
 
@@ -1502,7 +1502,7 @@ static int xhci_urb_enqueue(struct usb_h
 		 */
 		if (urb->dev->speed == USB_SPEED_FULL) {
 			ret = xhci_check_maxpacket(xhci, slot_id,
-					ep_index, urb);
+					ep_index, urb, mem_flags);
 			if (ret < 0) {
 				xhci_urb_free_priv(urb_priv);
 				urb->hcpriv = NULL;
author maintainer
#380 lore raw

PATCH 380/425 xhci: Add reset resume quirk for AMD xhci controller.

In reply to Greg Kroah-Hartman

From: Sandeep Singh <[email protected]>

commit 3c128781d8da463761495aaf8898c9ecb4e71528 upstream.

One of AMD xhci controller require reset on resume. Occasionally AMD xhci controller does not respond to Stop endpoint command.
Once the issue happens controller goes into bad state and in that case controller needs to be reset.

---
 drivers/usb/host/xhci-pci.c |    4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/usb/host/xhci-pci.c +3 -1
@@ -144,8 +144,10 @@ static void xhci_pci_quirks(struct devic
 	    (pdev->device == 0x15e0 || pdev->device == 0x15e1))
 		xhci->quirks |= XHCI_SNPS_BROKEN_SUSPEND;
 
-	if (pdev->vendor == PCI_VENDOR_ID_AMD && pdev->device == 0x15e5)
+	if (pdev->vendor == PCI_VENDOR_ID_AMD && pdev->device == 0x15e5) {
 		xhci->quirks |= XHCI_DISABLE_SPARSE;
+		xhci->quirks |= XHCI_RESET_ON_RESUME;
+	}
 
 	if (pdev->vendor == PCI_VENDOR_ID_AMD)
 		xhci->quirks |= XHCI_TRUST_TX_LENGTH;
author maintainer
#381 lore raw

PATCH 381/425 iio: gyro: mpu3050: Fix reported temperature value

In reply to Greg Kroah-Hartman

From: Dmitry Osipenko <[email protected]>

commit f73c730774d88a14d7b60feee6d0e13570f99499 upstream.

The raw temperature value is a 16-bit signed integer. The sign casting is missing in the code, which results in a wrong temperature reported by userspace tools, fix it.

Fixes 3904b28efb2c ("iio: gyro: Add driver for the MPU-3050 gyroscope")

Datasheet: https://www.cdiweb.com/datasheets/invensense/mpu-3000a.pdf

---
 drivers/iio/gyro/mpu3050-core.c |   13 +++++++++++--
 1 file changed, 11 insertions(+), 2 deletions(-)
drivers/iio/gyro/mpu3050-core.c +11 -2
@@ -270,7 +270,16 @@ static int mpu3050_read_raw(struct iio_d
 	case IIO_CHAN_INFO_OFFSET:
 		switch (chan->type) {
 		case IIO_TEMP:
-			/* The temperature scaling is (x+23000)/280 Celsius */
+			/*
+			 * The temperature scaling is (x+23000)/280 Celsius
+			 * for the "best fit straight line" temperature range
+			 * of -30C..85C.  The 23000 includes room temperature
+			 * offset of +35C, 280 is the precision scale and x is
+			 * the 16-bit signed integer reported by hardware.
+			 *
+			 * Temperature value itself represents temperature of
+			 * the sensor die.
+			 */
 			*val = 23000;
 			return IIO_VAL_INT;
 		default:
@@ -327,7 +336,7 @@ static int mpu3050_read_raw(struct iio_d
 				goto out_read_raw_unlock;
 			}
 
-			*val = be16_to_cpu(raw_val);
+			*val = (s16)be16_to_cpu(raw_val);
 			ret = IIO_VAL_INT;
 
 			goto out_read_raw_unlock;
author maintainer
#382 lore raw

PATCH 382/425 iio: tsl2583: Fix division by a zero lux_val

In reply to Greg Kroah-Hartman

From: Colin Ian King <[email protected]>

commit af0e1871d79cfbb91f732d2c6fa7558e45c31038 upstream.

The lux_val returned from tsl2583_get_lux can potentially be zero, so check for this to avoid a division by zero and an overflowed gain_trim_val.

Fixes clang scan-build warning:

drivers/iio/light/tsl2583.c:345:40: warning: Either the condition 'lux_val<0' is redundant or there is division by zero at line 345. [zerodivcond]

Fixes ac4f6eee8fe8 ("staging: iio: TAOS tsl258x: Device driver")
---
 drivers/iio/light/tsl2583.c |    8 ++++++++
 1 file changed, 8 insertions(+)
drivers/iio/light/tsl2583.c +8 -0
@@ -350,6 +350,14 @@ static int tsl2583_als_calibrate(struct
 		return lux_val;
 	}
 
+	/* Avoid division by zero of lux_value later on */
+	if (lux_val == 0) {
+		dev_err(&chip->client->dev,
+			"%s: lux_val of 0 will produce out of range trim_value\n",
+			__func__);
+		return -ENODATA;
+	}
+
 	gain_trim_val = (unsigned int)(((chip->als_settings.als_cal_target)
 			* chip->als_settings.als_gain_trim) / lux_val);
 	if ((gain_trim_val < 250) || (gain_trim_val > 4000)) {
author maintainer
#383 lore raw

PATCH 383/425 cdc-wdm: untangle a circular dependency between callback and softint

In reply to Greg Kroah-Hartman

From: Oliver Neukum <[email protected]>

commit 18abf874367456540846319574864e6ff32752e2 upstream.

We have a cycle of callbacks scheduling works which submit URBs with those callbacks. This needs to be blocked, stopped and unblocked to untangle the circle.

---
 drivers/usb/class/cdc-wdm.c |   30 ++++++++++++++++++++++--------
 1 file changed, 22 insertions(+), 8 deletions(-)
drivers/usb/class/cdc-wdm.c +22 -8
@@ -321,12 +321,23 @@ exit:
 
 }
 
-static void kill_urbs(struct wdm_device *desc)
+static void poison_urbs(struct wdm_device *desc)
 {
 	/* the order here is essential */
-	usb_kill_urb(desc->command);
-	usb_kill_urb(desc->validity);
-	usb_kill_urb(desc->response);
+	usb_poison_urb(desc->command);
+	usb_poison_urb(desc->validity);
+	usb_poison_urb(desc->response);
+}
+
+static void unpoison_urbs(struct wdm_device *desc)
+{
+	/*
+	 *  the order here is not essential
+	 *  it is symmetrical just to be nice
+	 */
+	usb_unpoison_urb(desc->response);
+	usb_unpoison_urb(desc->validity);
+	usb_unpoison_urb(desc->command);
 }
 
 static void free_urbs(struct wdm_device *desc)
@@ -741,11 +752,12 @@ static int wdm_release(struct inode *ino
 	if (!desc->count) {
 		if (!test_bit(WDM_DISCONNECTING, &desc->flags)) {
 			dev_dbg(&desc->intf->dev, "wdm_release: cleanup\n");
-			kill_urbs(desc);
+			poison_urbs(desc);
 			spin_lock_irq(&desc->iuspin);
 			desc->resp_count = 0;
 			spin_unlock_irq(&desc->iuspin);
 			desc->manage_power(desc->intf, 0);
+			unpoison_urbs(desc);
 		} else {
 			/* must avoid dev_printk here as desc->intf is invalid */
 			pr_debug(KBUILD_MODNAME " %s: device gone - cleaning up\n", __func__);
@@ -1036,9 +1048,9 @@ static void wdm_disconnect(struct usb_in
 	wake_up_all(&desc->wait);
 	mutex_lock(&desc->rlock);
 	mutex_lock(&desc->wlock);
+	poison_urbs(desc);
 	cancel_work_sync(&desc->rxwork);
 	cancel_work_sync(&desc->service_outs_intr);
-	kill_urbs(desc);
 	mutex_unlock(&desc->wlock);
 	mutex_unlock(&desc->rlock);
 
@@ -1079,9 +1091,10 @@ static int wdm_suspend(struct usb_interf
 		set_bit(WDM_SUSPENDING, &desc->flags);
 		spin_unlock_irq(&desc->iuspin);
 		/* callback submits work - order is essential */
-		kill_urbs(desc);
+		poison_urbs(desc);
 		cancel_work_sync(&desc->rxwork);
 		cancel_work_sync(&desc->service_outs_intr);
+		unpoison_urbs(desc);
 	}
 	if (!PMSG_IS_AUTO(message)) {
 		mutex_unlock(&desc->wlock);
@@ -1139,7 +1152,7 @@ static int wdm_pre_reset(struct usb_inte
 	wake_up_all(&desc->wait);
 	mutex_lock(&desc->rlock);
 	mutex_lock(&desc->wlock);
-	kill_urbs(desc);
+	poison_urbs(desc);
 	cancel_work_sync(&desc->rxwork);
 	cancel_work_sync(&desc->service_outs_intr);
 	return 0;
@@ -1150,6 +1163,7 @@ static int wdm_post_reset(struct usb_int
 	struct wdm_device *desc = wdm_find_device(intf);
 	int rv;
 
+	unpoison_urbs(desc);
 	clear_bit(WDM_OVERFLOW, &desc->flags);
 	clear_bit(WDM_RESETTING, &desc->flags);
 	rv = recover_from_urb_loss(desc);
author maintainer
#384 lore raw

PATCH 384/425 KVM: x86: Cancel pvclock_gtod_work on module removal

In reply to Greg Kroah-Hartman

From: Thomas Gleixner <[email protected]>

commit 594b27e677b35f9734b1969d175ebc6146741109 upstream.

Nothing prevents the following:

  pvclock_gtod_notify()
    queue_work(system_long_wq, &pvclock_gtod_work);
  ...
  remove_module(kvm);
  ...
  work_queue_run()
    pvclock_gtod_work()	<- UAF

Ditto for any other operation on that workqueue list head which touches pvclock_gtod_work after module removal.

Cancel the work in kvm_arch_exit() to prevent that.

Fixes 16e8d74d2da9 ("KVM: x86: notifier for clocksource changes")

Message-Id: <[email protected]>

---
 arch/x86/kvm/x86.c |    1 +
 1 file changed, 1 insertion(+)
arch/x86/kvm/x86.c +1 -0
@@ -6911,6 +6911,7 @@ void kvm_arch_exit(void)
 	cpuhp_remove_state_nocalls(CPUHP_AP_X86_KVM_CLK_ONLINE);
 #ifdef CONFIG_X86_64
 	pvclock_gtod_unregister_notifier(&pvclock_gtod_notifier);
+	cancel_work_sync(&pvclock_gtod_work);
 #endif
 	kvm_x86_ops = NULL;
 	kvm_mmu_module_exit();
author maintainer
#385 lore raw

PATCH 385/425 FDDI: defxx: Make MMIO the configuration default except for EISA

In reply to Greg Kroah-Hartman

From: Maciej W. Rozycki <[email protected]>

commit 193ced4a79599352d63cb8c9e2f0c6043106eb6a upstream.

Recent versions of the PCI Express specification have deprecated support for I/O transactions and actually some PCIe host bridges, such as Power Systems Host Bridge 4 (PHB4), do not implement them.

The default kernel configuration choice for the defxx driver is the use of I/O ports rather than MMIO for PCI and EISA systems. It may have made sense as a conservative backwards compatible choice back when MMIO operation support was added to the driver as a part of TURBOchannel bus support. However nowadays this configuration choice makes the driver unusable with systems that do not implement I/O transactions for PCIe.

Make DEFXX_MMIO the configuration default then, except where configured for EISA. This exception is because an EISA adapter can have its MMIO decoding disabled with ECU (EISA Configuration Utility) and therefore not available with the resource allocation infrastructure we implement, while port I/O is always readily available as it uses slot-specific addressing, directly mapped to the slot an option card has been placed in and handled with our EISA bus support core. Conversely a kernel that supports modern systems which may not have I/O transactions implemented for PCIe will usually not be expected to handle legacy EISA systems.

The change of the default will make it easier for people, including but not limited to distribution packagers, to make a working choice for the driver.

Update the option description accordingly and while at it replace the potentially ambiguous PIO acronym with IOP for "port I/O" vs "I/O ports" according to our nomenclature used elsewhere.

Fixes e89a2cfb7d7b ("[TC] defxx: TURBOchannel support")
Cc [email protected] # v2.6.21+
---
 drivers/net/fddi/Kconfig |   15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)
drivers/net/fddi/Kconfig +9 -6
@@ -28,17 +28,20 @@ config DEFXX
 
 config DEFXX_MMIO
 	bool
-	prompt "Use MMIO instead of PIO" if PCI || EISA
+	prompt "Use MMIO instead of IOP" if PCI || EISA
 	depends on DEFXX
-	default n if PCI || EISA
+	default n if EISA
 	default y
 	---help---
 	  This instructs the driver to use EISA or PCI memory-mapped I/O
-	  (MMIO) as appropriate instead of programmed I/O ports (PIO).
+	  (MMIO) as appropriate instead of programmed I/O ports (IOP).
 	  Enabling this gives an improvement in processing time in parts
-	  of the driver, but it may cause problems with EISA (DEFEA)
-	  adapters.  TURBOchannel does not have the concept of I/O ports,
-	  so MMIO is always used for these (DEFTA) adapters.
+	  of the driver, but it requires a memory window to be configured
+	  for EISA (DEFEA) adapters that may not always be available.
+	  Conversely some PCIe host bridges do not support IOP, so MMIO
+	  may be required to access PCI (DEFPA) adapters on downstream PCI
+	  buses with some systems.  TURBOchannel does not have the concept
+	  of I/O ports, so MMIO is always used for these (DEFTA) adapters.
 
 	  If unsure, say N.
 
author maintainer
#386 lore raw

PATCH 386/425 MIPS: Reinstate platform `__div64_32 handler

In reply to Greg Kroah-Hartman

From: Maciej W. Rozycki <[email protected]>

commit c49f71f60754acbff37505e1d16ca796bf8a8140 upstream.

Our current MIPS platform __div64_32' handler is inactive, because it is incorrectly only enabled for 64-bit configurations, for which generic do_div' code does not call it anyway.

The handler is not suitable for being called from there though as it only calculates 32 bits of the quotient under the assumption the 64-bit divident has been suitably reduced. Code for such reduction used to be there, however it has been incorrectly removed with commit c21004cd5b4c ("MIPS: Rewrite <asm/div64.h> to work with gcc 4.4.0."), which should have only updated an obsoleted constraint for an inline asm involving $hi and $lo register outputs, while possibly wiring the original MIPS variant of the do_div' macro as __div64_32' handler for the generic `do_div' implementation

Correct the handler as follows then:

- Revert most of the commit referred, however retaining the current formatting, except for the final two instructions of the inline asm sequence, which the original commit missed. Omit the original 64-bit parts though.

- Rename the original do_div' macro to __div64_32'. Use the combined x' constraint referring to the MD accumulator as a whole, replacing the original individual h' and l' constraints used for $hi and $lo registers respectively, of which h' has been obsoleted with GCC 4.4. Update surrounding code accordingly.

We have since removed support for GCC versions before 4.9, so no need for a special arrangement here; GCC has supported the `x' constraint since forever anyway, or at least going back to 1991.

- Rename the __base' local variable in __div64_32' to __radix' to avoid a conflict with a local variable in do_div'.

- Actually enable this code for 32-bit rather than 64-bit configurations by qualifying it with BITS_PER_LONG being 32 instead of 64. Include <asm/bitsperlong.h> for this macro rather than <linux/types.h> as we don't need anything else.

- Finally include <asm-generic/div64.h> last rather than first.

This has passed correctness verification with test_div64 and reduced the module's average execution time down to 1.0668s and 0.2629s from 2.1529s and 0.5647s respectively for an R3400 CPU @40MHz and a 5Kc CPU @160MHz. For a reference 64-bit `do_div' code where we have the DDIVU instruction available to do the whole calculation right away averages at 0.0660s for the latter CPU.

Fixes c21004cd5b4c ("MIPS: Rewrite <asm/div64.h> to work with gcc 4.4.0.")
Cc [email protected] # v2.6.30+
---
 arch/mips/include/asm/div64.h |   57 ++++++++++++++++++++++++++++++------------
 1 file changed, 41 insertions(+), 16 deletions(-)
arch/mips/include/asm/div64.h +41 -16
@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2000, 2004  Maciej W. Rozycki
+ * Copyright (C) 2000, 2004, 2021  Maciej W. Rozycki
  * Copyright (C) 2003, 07 Ralf Baechle ([email protected])
  *
  * This file is subject to the terms and conditions of the GNU General Public
@@ -9,25 +9,18 @@
 #ifndef __ASM_DIV64_H
 #define __ASM_DIV64_H
 
-#include <asm-generic/div64.h>
-
-#if BITS_PER_LONG == 64
+#include <asm/bitsperlong.h>
 
-#include <linux/types.h>
+#if BITS_PER_LONG == 32
 
 /*
  * No traps on overflows for any of these...
  */
 
-#define __div64_32(n, base)						\
-({									\
+#define do_div64_32(res, high, low, base) ({				\
 	unsigned long __cf, __tmp, __tmp2, __i;				\
 	unsigned long __quot32, __mod32;				\
-	unsigned long __high, __low;					\
-	unsigned long long __n;						\
 									\
-	__high = *__n >> 32;						\
-	__low = __n;							\
 	__asm__(							\
 	"	.set	push					\n"	\
 	"	.set	noat					\n"	\
@@ -51,18 +44,50 @@
 	"	subu	%0, %0, %z6				\n"	\
 	"	addiu	%2, %2, 1				\n"	\
 	"3:							\n"	\
-	"	bnez	%4, 0b\n\t"					\
-	"	 srl	%5, %1, 0x1f\n\t"				\
+	"	bnez	%4, 0b					\n"	\
+	"	 srl	%5, %1, 0x1f				\n"	\
 	"	.set	pop"						\
 	: "=&r" (__mod32), "=&r" (__tmp),				\
 	  "=&r" (__quot32), "=&r" (__cf),				\
 	  "=&r" (__i), "=&r" (__tmp2)					\
-	: "Jr" (base), "0" (__high), "1" (__low));			\
+	: "Jr" (base), "0" (high), "1" (low));				\
 									\
-	(__n) = __quot32;						\
+	(res) = __quot32;						\
 	__mod32;							\
 })
 
-#endif /* BITS_PER_LONG == 64 */
+#define __div64_32(n, base) ({						\
+	unsigned long __upper, __low, __high, __radix;			\
+	unsigned long long __modquot;					\
+	unsigned long long __quot;					\
+	unsigned long long __div;					\
+	unsigned long __mod;						\
+									\
+	__div = (*n);							\
+	__radix = (base);						\
+									\
+	__high = __div >> 32;						\
+	__low = __div;							\
+	__upper = __high;						\
+									\
+	if (__high) {							\
+		__asm__("divu	$0, %z1, %z2"				\
+		: "=x" (__modquot)					\
+		: "Jr" (__high), "Jr" (__radix));			\
+		__upper = __modquot >> 32;				\
+		__high = __modquot;					\
+	}								\
+									\
+	__mod = do_div64_32(__low, __upper, __low, __radix);		\
+									\
+	__quot = __high;						\
+	__quot = __quot << 32 | __low;					\
+	(*n) = __quot;							\
+	__mod;								\
+})
+
+#endif /* BITS_PER_LONG == 32 */
+
+#include <asm-generic/div64.h>
 
 #endif /* __ASM_DIV64_H */
author maintainer
#387 lore raw

PATCH 387/425 MIPS: Avoid DIVU in `__div64_32 is result would be zero

In reply to Greg Kroah-Hartman

From: Maciej W. Rozycki <[email protected]>

commit c1d337d45ec0a802299688e17d568c4e3a585895 upstream.

We already check the high part of the divident against zero to avoid the costly DIVU instruction in that case, needed to reduce the high part of the divident, so we may well check against the divisor instead and set the high part of the quotient to zero right away. We need to treat the high part the divident in that case though as the remainder that would be calculated by the DIVU instruction we avoided.

This has passed correctness verification with test_div64 and reduced the module's average execution time down to 1.0445s and 0.2619s from 1.0668s and 0.2629s respectively for an R3400 CPU @40MHz and a 5Kc CPU @160MHz.

---
 arch/mips/include/asm/div64.h |    6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
arch/mips/include/asm/div64.h +4 -2
@@ -68,9 +68,11 @@
 									\
 	__high = __div >> 32;						\
 	__low = __div;							\
-	__upper = __high;						\
 									\
-	if (__high) {							\
+	if (__high < __radix) {						\
+		__upper = __high;					\
+		__high = 0;						\
+	} else {							\
 		__asm__("divu	$0, %z1, %z2"				\
 		: "=x" (__modquot)					\
 		: "Jr" (__high), "Jr" (__radix));			\
author maintainer
#388 lore raw

PATCH 388/425 MIPS: Avoid handcoded DIVU in `__div64_32 altogether

In reply to Greg Kroah-Hartman

From: Maciej W. Rozycki <[email protected]>

commit 25ab14cbe9d1b66fda44c71a2db7582a31b6f5cd upstream.

Remove the inline asm with a DIVU instruction from `__div64_32' and use plain C code for the intended DIVMOD calculation instead. GCC is smart enough to know that both the quotient and the remainder are calculated with single DIVU, so with ISAs up to R5 the same instruction is actually produced with overall similar code.

For R6 compiled code will work, but separate DIVU and MODU instructions will be produced, which are also interlocked, so scalar implementations will likely not perform as well as older ISAs with their asynchronous MD unit. Likely still faster then the generic algorithm though.

This removes a compilation error for R6 however where the original DIVU instruction is not supported anymore and the MDU accumulator registers have been removed and consequently GCC complains as to a constraint it cannot find a register for:

In file included from ./include/linux/math.h:5,

                 from ./include/linux/kernel.h:13,
                 from mm/page-writeback.c:15:
./include/linux/math64.h: In function 'div_u64_rem':
./arch/mips/include/asm/div64.h:76:17: error: inconsistent operand constraints in an 'asm'
   76 |                 __asm__("divu   $0, %z1, %z2"                           \
      |                 ^~~~~~~
./include/asm-generic/div64.h:245:25: note: in expansion of macro '__div64_32'
  245 |                 __rem = __div64_32(&(n), __base);       \
      |                         ^~~~~~~~~~

./include/linux/math64.h:91:22: note: in expansion of macro 'do_div'
91 | *remainder = do_div(dividend, divisor);
| ^~~~~~

This has passed correctness verification with test_div64 and reduced the module's average execution time down to 1.0404s from 1.0445s with R3400 @40MHz. The module's MIPS I machine code has also shrunk by 12 bytes or 3 instructions.

---
 arch/mips/include/asm/div64.h |    8 ++------
 1 file changed, 2 insertions(+), 6 deletions(-)
arch/mips/include/asm/div64.h +2 -6
@@ -58,7 +58,6 @@
 
 #define __div64_32(n, base) ({						\
 	unsigned long __upper, __low, __high, __radix;			\
-	unsigned long long __modquot;					\
 	unsigned long long __quot;					\
 	unsigned long long __div;					\
 	unsigned long __mod;						\
@@ -73,11 +72,8 @@
 		__upper = __high;					\
 		__high = 0;						\
 	} else {							\
-		__asm__("divu	$0, %z1, %z2"				\
-		: "=x" (__modquot)					\
-		: "Jr" (__high), "Jr" (__radix));			\
-		__upper = __modquot >> 32;				\
-		__high = __modquot;					\
+		__upper = __high % __radix;				\
+		__high /= __radix;					\
 	}								\
 									\
 	__mod = do_div64_32(__low, __upper, __low, __radix);		\
author maintainer
#389 lore raw

PATCH 389/425 thermal/core/fair share: Lock the thermal zone while looping over instances

In reply to Greg Kroah-Hartman

From: Lukasz Luba <[email protected]>

commit fef05776eb02238dcad8d5514e666a42572c3f32 upstream.

The tz->lock must be hold during the looping over the instances in that thermal zone. This lock was missing in the governor code since the beginning, so it's hard to point into a particular commit.

---
 drivers/thermal/fair_share.c |    4 ++++
 1 file changed, 4 insertions(+)
drivers/thermal/fair_share.c +4 -0
@@ -94,6 +94,8 @@ static int fair_share_throttle(struct th
 	int total_instance = 0;
 	int cur_trip_level = get_trip_level(tz);
 
+	mutex_lock(&tz->lock);
+
 	list_for_each_entry(instance, &tz->thermal_instances, tz_node) {
 		if (instance->trip != trip)
 			continue;
@@ -122,6 +124,8 @@ static int fair_share_throttle(struct th
 		mutex_unlock(&instance->cdev->lock);
 		thermal_cdev_update(cdev);
 	}
+
+	mutex_unlock(&tz->lock);
 	return 0;
 }
 
author maintainer
#390 lore raw

PATCH 390/425 kobject_uevent: remove warning in init_uevent_argv()

In reply to Greg Kroah-Hartman

From: Greg Kroah-Hartman <[email protected]>

commit b4104180a2efb85f55e1ba1407885c9421970338 upstream.

syzbot can trigger the WARN() in init_uevent_argv() which isn't the nicest as the code does properly recover and handle the error. So change the WARN() call to pr_warn() and provide some more information on what the buffer size that was needed.

---
 lib/kobject_uevent.c |    9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)
lib/kobject_uevent.c +5 -4
@@ -250,12 +250,13 @@ static int kobj_usermode_filter(struct k
 
 static int init_uevent_argv(struct kobj_uevent_env *env, const char *subsystem)
 {
+	int buffer_size = sizeof(env->buf) - env->buflen;
 	int len;
 
-	len = strlcpy(&env->buf[env->buflen], subsystem,
-		      sizeof(env->buf) - env->buflen);
-	if (len >= (sizeof(env->buf) - env->buflen)) {
-		WARN(1, KERN_ERR "init_uevent_argv: buffer size too small\n");
+	len = strlcpy(&env->buf[env->buflen], subsystem, buffer_size);
+	if (len >= buffer_size) {
+		pr_warn("init_uevent_argv: buffer size of %d too small, needed %d\n",
+			buffer_size, len);
 		return -ENOMEM;
 	}
 
author maintainer
#391 lore raw

PATCH 391/425 netfilter: conntrack: Make global sysctls readonly in non-init netns

In reply to Greg Kroah-Hartman

From: Jonathon Reinhart <[email protected]>

commit 2671fa4dc0109d3fb581bc3078fdf17b5d9080f6 upstream.

These sysctls point to global variables:
- NF_SYSCTL_CT_MAX (&nf_conntrack_max)
- NF_SYSCTL_CT_EXPECT_MAX (&nf_ct_expect_max)
- NF_SYSCTL_CT_BUCKETS (&nf_conntrack_htable_size_user)

Because their data pointers are not updated to point to per-netns structures, they must be marked read-only in a non-init_net ns. Otherwise, changes in any net namespace are reflected in (leaked into) all other net namespaces. This problem has existed since the introduction of net namespaces.

The current logic marks them read-only only if the net namespace is owned by an unprivileged user (other than init_user_ns).

Commit d0febd81ae77 ("netfilter: conntrack: re-visit sysctls in unprivileged namespaces") "exposes all sysctls even if the namespace is unpriviliged." Since we need to mark them readonly in any case, we can forego the unprivileged user check altogether.

Fixes d0febd81ae77 ("netfilter: conntrack: re-visit sysctls in unprivileged namespaces")
---
 net/netfilter/nf_conntrack_standalone.c |    5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
net/netfilter/nf_conntrack_standalone.c +4 -1
@@ -594,8 +594,11 @@ static int nf_conntrack_standalone_init_
 	if (net->user_ns != &init_user_ns)
 		table[0].procname = NULL;
 
-	if (!net_eq(&init_net, net))
+	if (!net_eq(&init_net, net)) {
+		table[0].mode = 0444;
 		table[2].mode = 0444;
+		table[5].mode = 0444;
+	}
 
 	net->ct.sysctl_header = register_net_sysctl(net, "net/netfilter", table);
 	if (!net->ct.sysctl_header)
author maintainer
#392 lore raw

PATCH 392/425 clk: exynos7: Mark aclk_fsys1_200 as critical

In reply to Greg Kroah-Hartman

From: Paweł Chmiel <[email protected]>

commit 34138a59b92c1a30649a18ec442d2e61f3bc34dd upstream.

This clock must be always enabled to allow access to any registers in fsys1 CMU. Until proper solution based on runtime PM is applied (similar to what was done for Exynos5433), mark that clock as critical so it won't be disabled.

It was observed on Samsung Galaxy S6 device (based on Exynos7420), where UFS module is probed before pmic used to power that device. In this case defer probe was happening and that clock was disabled by UFS driver, causing whole boot to hang on next CMU access.

Fixes 753195a749a6 ("clk: samsung: exynos7: Correct CMU_FSYS1 clocks names")
[s.nawrocki: Added comment in the code]
---
 drivers/clk/samsung/clk-exynos7.c |    7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)
drivers/clk/samsung/clk-exynos7.c +6 -1
@@ -541,8 +541,13 @@ static const struct samsung_gate_clock t
 	GATE(CLK_ACLK_FSYS0_200, "aclk_fsys0_200", "dout_aclk_fsys0_200",
 		ENABLE_ACLK_TOP13, 28, CLK_SET_RATE_PARENT |
 		CLK_IS_CRITICAL, 0),
+	/*
+	 * This clock is required for the CMU_FSYS1 registers access, keep it
+	 * enabled permanently until proper runtime PM support is added.
+	 */
 	GATE(CLK_ACLK_FSYS1_200, "aclk_fsys1_200", "dout_aclk_fsys1_200",
-		ENABLE_ACLK_TOP13, 24, CLK_SET_RATE_PARENT, 0),
+		ENABLE_ACLK_TOP13, 24, CLK_SET_RATE_PARENT |
+		CLK_IS_CRITICAL, 0),
 
 	GATE(CLK_SCLK_PHY_FSYS1_26M, "sclk_phy_fsys1_26m",
 		"dout_sclk_phy_fsys1_26m", ENABLE_SCLK_TOP1_FSYS11,
author maintainer
#393 lore raw

PATCH 393/425 nvme: do not try to reconfigure APST when the controller is not live

In reply to Greg Kroah-Hartman

From: Christoph Hellwig <[email protected]>

commit 53fe2a30bc168db9700e00206d991ff934973cf1 upstream.

Do not call nvme_configure_apst when the controller is not live, given that nvme_configure_apst will fail due the lack of an admin queue when the controller is being torn down and nvme_set_latency_tolerance is called from dev_pm_qos_hide_latency_tolerance.

Fixes 510a405d945b("nvme: fix memory leak for power latency tolerance")
---
 drivers/nvme/host/core.c |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/nvme/host/core.c +2 -1
@@ -2091,7 +2091,8 @@ static void nvme_set_latency_tolerance(s
 
 	if (ctrl->ps_max_latency_us != latency) {
 		ctrl->ps_max_latency_us = latency;
-		nvme_configure_apst(ctrl);
+		if (ctrl->state == NVME_CTRL_LIVE)
+			nvme_configure_apst(ctrl);
 	}
 }
 
author maintainer
#394 lore raw

PATCH 394/425 x86/msr: Fix wr/rdmsr_safe_regs_on_cpu() prototypes

In reply to Greg Kroah-Hartman

From: Arnd Bergmann <[email protected]>

commit 396a66aa1172ef2b78c21651f59b40b87b2e5e1e upstream.

gcc-11 warns about mismatched prototypes here:

arch/x86/lib/msr-smp.c:255:51: error: argument 2 of type ‘u32 *’ {aka ‘unsigned int *’} declared as a pointer [-Werror=array-parameter=]
255 | int rdmsr_safe_regs_on_cpu(unsigned int cpu, u32 *regs)
| ~~~~~^~~~
arch/x86/include/asm/msr.h:347:50: note: previously declared as an array ‘u32[8]’ {aka ‘unsigned int[8]’}

GCC is right here - fix up the types.

[ mingo: Twiddled the changelog. ]

---
 arch/x86/lib/msr-smp.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
arch/x86/lib/msr-smp.c +2 -2
@@ -253,7 +253,7 @@ static void __wrmsr_safe_regs_on_cpu(voi
 	rv->err = wrmsr_safe_regs(rv->regs);
 }
 
-int rdmsr_safe_regs_on_cpu(unsigned int cpu, u32 *regs)
+int rdmsr_safe_regs_on_cpu(unsigned int cpu, u32 regs[8])
 {
 	int err;
 	struct msr_regs_info rv;
@@ -266,7 +266,7 @@ int rdmsr_safe_regs_on_cpu(unsigned int
 }
 EXPORT_SYMBOL(rdmsr_safe_regs_on_cpu);
 
-int wrmsr_safe_regs_on_cpu(unsigned int cpu, u32 *regs)
+int wrmsr_safe_regs_on_cpu(unsigned int cpu, u32 regs[8])
 {
 	int err;
 	struct msr_regs_info rv;
author maintainer
#395 lore raw

PATCH 395/425 kgdb: fix gcc-11 warning on indentation

In reply to Greg Kroah-Hartman

From: Arnd Bergmann <[email protected]>

commit 40cc3a80bb42587db1e6ae21d6f3090582d33e89 upstream.

gcc-11 starts warning about misleading indentation inside of macros:

drivers/misc/kgdbts.c: In function ‘kgdbts_break_test’:
drivers/misc/kgdbts.c:103:9: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]

  103 |         if (verbose > 1) \
      |         ^~
drivers/misc/kgdbts.c:200:9: note: in expansion of macro ‘v2printk’
  200 |         v2printk("kgdbts: breakpoint complete\n");
      |         ^~~~~~~~
drivers/misc/kgdbts.c:105:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
  105 |                 touch_nmi_watchdog();   \
      |                 ^~~~~~~~~~~~~~~~~~

The code looks correct to me, so just reindent it for readability.

---
 drivers/misc/kgdbts.c |   26 +++++++++++++-------------
 1 file changed, 13 insertions(+), 13 deletions(-)
drivers/misc/kgdbts.c +13 -13
@@ -107,19 +107,19 @@
 
 #include <asm/sections.h>
 
-#define v1printk(a...) do { \
-	if (verbose) \
-		printk(KERN_INFO a); \
-	} while (0)
-#define v2printk(a...) do { \
-	if (verbose > 1) \
-		printk(KERN_INFO a); \
-		touch_nmi_watchdog();	\
-	} while (0)
-#define eprintk(a...) do { \
-		printk(KERN_ERR a); \
-		WARN_ON(1); \
-	} while (0)
+#define v1printk(a...) do {		\
+	if (verbose)			\
+		printk(KERN_INFO a);	\
+} while (0)
+#define v2printk(a...) do {		\
+	if (verbose > 1)		\
+		printk(KERN_INFO a);	\
+	touch_nmi_watchdog();		\
+} while (0)
+#define eprintk(a...) do {		\
+	printk(KERN_ERR a);		\
+	WARN_ON(1);			\
+} while (0)
 #define MAX_CONFIG_LEN		40
 
 static struct kgdb_io kgdbts_io_ops;
author maintainer
#396 lore raw

PATCH 396/425 usb: sl811-hcd: improve misleading indentation

In reply to Greg Kroah-Hartman

From: Arnd Bergmann <[email protected]>

commit 8460f6003a1d2633737b89c4f69d6f4c0c7c65a3 upstream.

gcc-11 now warns about a confusingly indented code block:

drivers/usb/host/sl811-hcd.c: In function ‘sl811h_hub_control’:
drivers/usb/host/sl811-hcd.c:1291:9: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]

 1291 |         if (*(u16*)(buf+2))     /* only if wPortChange is interesting */
      |         ^~

drivers/usb/host/sl811-hcd.c:1295:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
1295 | break;

Rewrite this to use a single if() block with the __is_defined() macro.

---
 drivers/usb/host/sl811-hcd.c |    9 ++++-----
 1 file changed, 4 insertions(+), 5 deletions(-)
drivers/usb/host/sl811-hcd.c +4 -5
@@ -1287,11 +1287,10 @@ sl811h_hub_control(
 			goto error;
 		put_unaligned_le32(sl811->port1, buf);
 
-#ifndef	VERBOSE
-	if (*(u16*)(buf+2))	/* only if wPortChange is interesting */
-#endif
-		dev_dbg(hcd->self.controller, "GetPortStatus %08x\n",
-			sl811->port1);
+		if (__is_defined(VERBOSE) ||
+		    *(u16*)(buf+2)) /* only if wPortChange is interesting */
+			dev_dbg(hcd->self.controller, "GetPortStatus %08x\n",
+				sl811->port1);
 		break;
 	case SetPortFeature:
 		if (wIndex != 1 || wLength != 0)
author maintainer
#397 lore raw

PATCH 397/425 cxgb4: Fix the -Wmisleading-indentation warning

In reply to Greg Kroah-Hartman

From: Kaixu Xia <[email protected]>

commit ea8146c6845799142aa4ee2660741c215e340cdf upstream.

Fix the gcc warning:

drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c:2673:9: warning: this 'for' clause does not guard... [-Wmisleading-indentation]
2673 | for (i = 0; i < n; ++i) \

---
 drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c +1 -1
@@ -2730,7 +2730,7 @@ do { \
 	seq_printf(seq, "%-12s", s); \
 	for (i = 0; i < n; ++i) \
 		seq_printf(seq, " %16" fmt_spec, v); \
-		seq_putc(seq, '\n'); \
+	seq_putc(seq, '\n'); \
 } while (0)
 #define S(s, v) S3("s", s, v)
 #define T3(fmt_spec, s, v) S3(fmt_spec, s, tx[i].v)
author maintainer
#398 lore raw

PATCH 398/425 isdn: capi: fix mismatched prototypes

In reply to Greg Kroah-Hartman

From: Arnd Bergmann <[email protected]>

commit 5ee7d4c7fbc9d3119a20b1c77d34003d1f82ac26 upstream.

gcc-11 complains about a prototype declaration that is different from the function definition:

drivers/isdn/capi/kcapi.c:724:44: error: argument 2 of type ‘u8 *’ {aka ‘unsigned char *’} declared as a pointer [-Werror=array-parameter=]
724 | u16 capi20_get_manufacturer(u32 contr, u8 *buf)
| ~~~~^~~
In file included from drivers/isdn/capi/kcapi.c:13:
drivers/isdn/capi/kcapi.h:62:43: note: previously declared as an array ‘u8[64]’ {aka ‘unsigned char[64]’}

   62 | u16 capi20_get_manufacturer(u32 contr, u8 buf[CAPI_MANUFACTURER_LEN]);
      |                                        ~~~^~~~~~~~~~~~~~~~~~~~~~~~~~

drivers/isdn/capi/kcapi.c:790:38: error: argument 2 of type ‘u8 *’ {aka ‘unsigned char *’} declared as a pointer [-Werror=array-parameter=]
790 | u16 capi20_get_serial(u32 contr, u8 *serial)
| ~~~~^~~~~~
In file included from drivers/isdn/capi/kcapi.c:13:
drivers/isdn/capi/kcapi.h:64:37: note: previously declared as an array ‘u8[8]’ {aka ‘unsigned char[8]’}

   64 | u16 capi20_get_serial(u32 contr, u8 serial[CAPI_SERIAL_LEN]);
      |                                  ~~~^~~~~~~~~~~~~~~~~~~~~~~

Change the definition to make them match.

---
 drivers/isdn/capi/kcapi.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/isdn/capi/kcapi.c +2 -2
@@ -846,7 +846,7 @@ EXPORT_SYMBOL(capi20_put_message);
  * Return value: CAPI result code
  */
 
-u16 capi20_get_manufacturer(u32 contr, u8 *buf)
+u16 capi20_get_manufacturer(u32 contr, u8 buf[CAPI_MANUFACTURER_LEN])
 {
 	struct capi_ctr *ctr;
 	u16 ret;
@@ -916,7 +916,7 @@ EXPORT_SYMBOL(capi20_get_version);
  * Return value: CAPI result code
  */
 
-u16 capi20_get_serial(u32 contr, u8 *serial)
+u16 capi20_get_serial(u32 contr, u8 serial[CAPI_SERIAL_LEN])
 {
 	struct capi_ctr *ctr;
 	u16 ret;
author maintainer
#399 lore raw

PATCH 399/425 pinctrl: ingenic: Improve unreachable code generation

In reply to Greg Kroah-Hartman

From: Josh Poimboeuf <[email protected]>

[ Upstream commit d6d43a92172085a2681e06a0d06aac53c7bcdd12 ]

In the second loop of ingenic_pinconf_set(), it annotates the switch default case as unreachable(). The annotation is technically correct, because that same case would have resulted in an early function return in the previous loop.

However, the compiled code is suboptimal. GCC seems to work extra hard to ensure that the unreachable code path triggers undefined behavior. The function would fall through to start executing whatever function happens to be next in the compilation unit.

This is problematic because:

a) it adds unnecessary 'ensure undefined behavior' logic, and corresponding i-cache footprint; and

b) it's less robust -- if a bug were to be introduced, falling through to the next function would be catastrophic.

Yet another issue is that, while objtool normally understands unreachable() annotations, there's one special case where it doesn't:
when the annotation occurs immediately after a 'ret' instruction. That happens to be the case here because unreachable() is immediately before the return.

Remove the unreachable() annotation and replace it with a comment. This simplifies the code generation and changes the unreachable error path to just silently return instead of corrupting execution.

This fixes the following objtool warning:

drivers/pinctrl/pinctrl-ingenic.o: warning: objtool: ingenic_pinconf_set() falls through to next function ingenic_pinconf_group_set()

---
 drivers/pinctrl/pinctrl-ingenic.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/pinctrl/pinctrl-ingenic.c +2 -1
index a5accffbc8c9..babf6d011264 100644
@@ -642,7 +642,8 @@ static int ingenic_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
 			break;
 
 		default:
-			unreachable();
+			/* unreachable */
+			break;
 		}
 	}
 
Signature · 1 line
2.30.2
author maintainer
#400 lore raw

PATCH 400/425 xsk: Simplify detection of empty and full rings

In reply to Greg Kroah-Hartman

From: Magnus Karlsson <[email protected]>

[ Upstream commit 11cc2d21499cabe7e7964389634ed1de3ee91d33 ]

In order to set the correct return flags for poll, the xsk code has to check if the Rx queue is empty and if the Tx queue is full. This code was unnecessarily large and complex as it used the functions that are used to update the local state from the global state (xskq_nb_free and xskq_nb_avail). Since we are not doing this nor updating any data dependent on this state, we can simplify the functions. Another benefit from this is that we can also simplify the xskq_nb_free and xskq_nb_avail functions in a later commit.

---
 net/xdp/xsk_queue.h | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)
net/xdp/xsk_queue.h +5 -2
index fe96c0d039f2..cf7cbb5dd918 100644
@@ -245,12 +245,15 @@ static inline void xskq_produce_flush_desc(struct xsk_queue *q)
 
 static inline bool xskq_full_desc(struct xsk_queue *q)
 {
-	return xskq_nb_avail(q, q->nentries) == q->nentries;
+	/* No barriers needed since data is not accessed */
+	return READ_ONCE(q->ring->producer) - READ_ONCE(q->ring->consumer) ==
+		q->nentries;
 }
 
 static inline bool xskq_empty_desc(struct xsk_queue *q)
 {
-	return xskq_nb_free(q, q->prod_tail, q->nentries) == q->nentries;
+	/* No barriers needed since data is not accessed */
+	return READ_ONCE(q->ring->consumer) == READ_ONCE(q->ring->producer);
 }
 
 void xskq_set_umem(struct xsk_queue *q, struct xdp_umem_props *umem_props);
Signature · 1 line
2.30.2
author maintainer
#401 lore raw

PATCH 401/425 ARM: 9058/1: cache-v7: refactor v7_invalidate_l1 to avoid clobbering r5/r6

In reply to Greg Kroah-Hartman

From: Ard Biesheuvel <[email protected]>

[ Upstream commit f9e7a99fb6b86aa6a00e53b34ee6973840e005aa ]

The cache invalidation code in v7_invalidate_l1 can be tweaked to re-read the associativity from CCSIDR, and keep the way identifier component in a single register that is assigned in the outer loop. This way, we need 2 registers less.

Given that the number of sets is typically much larger than the associativity, rearrange the code so that the outer loop has the fewer number of iterations, ensuring that the re-read of CCSIDR only occurs a handful of times in practice.

Fix the whitespace while at it, and update the comment to indicate that this code is no longer a clone of anything else.

---
 arch/arm/mm/cache-v7.S | 51 +++++++++++++++++++++---------------------
 1 file changed, 25 insertions(+), 26 deletions(-)
arch/arm/mm/cache-v7.S +25 -26
index 2149b47a0c5a..463965dc7922 100644
@@ -28,41 +28,40 @@
  * processor.  We fix this by performing an invalidate, rather than a
  * clean + invalidate, before jumping into the kernel.
  *
- * This function is cloned from arch/arm/mach-tegra/headsmp.S, and needs
- * to be called for both secondary cores startup and primary core resume
- * procedures.
+ * This function needs to be called for both secondary cores startup and
+ * primary core resume procedures.
  */
 ENTRY(v7_invalidate_l1)
        mov     r0, #0
        mcr     p15, 2, r0, c0, c0, 0
        mrc     p15, 1, r0, c0, c0, 0
 
-       movw    r1, #0x7fff
-       and     r2, r1, r0, lsr #13
+	movw	r3, #0x3ff
+	and	r3, r3, r0, lsr #3	@ 'Associativity' in CCSIDR[12:3]
+	clz	r1, r3			@ WayShift
+	mov	r2, #1
+	mov	r3, r3, lsl r1		@ NumWays-1 shifted into bits [31:...]
+	movs	r1, r2, lsl r1		@ #1 shifted left by same amount
+	moveq	r1, #1			@ r1 needs value > 0 even if only 1 way
 
-       movw    r1, #0x3ff
+	and	r2, r0, #0x7
+	add	r2, r2, #4		@ SetShift
 
-       and     r3, r1, r0, lsr #3      @ NumWays - 1
-       add     r2, r2, #1              @ NumSets
+1:	movw	r4, #0x7fff
+	and	r0, r4, r0, lsr #13	@ 'NumSets' in CCSIDR[27:13]
 
-       and     r0, r0, #0x7
-       add     r0, r0, #4      @ SetShift
-
-       clz     r1, r3          @ WayShift
-       add     r4, r3, #1      @ NumWays
-1:     sub     r2, r2, #1      @ NumSets--
-       mov     r3, r4          @ Temp = NumWays
-2:     subs    r3, r3, #1      @ Temp--
-       mov     r5, r3, lsl r1
-       mov     r6, r2, lsl r0
-       orr     r5, r5, r6      @ Reg = (Temp<<WayShift)|(NumSets<<SetShift)
-       mcr     p15, 0, r5, c7, c6, 2
-       bgt     2b
-       cmp     r2, #0
-       bgt     1b
-       dsb     st
-       isb
-       ret     lr
+2:	mov	r4, r0, lsl r2		@ NumSet << SetShift
+	orr	r4, r4, r3		@ Reg = (Temp<<WayShift)|(NumSets<<SetShift)
+	mcr	p15, 0, r4, c7, c6, 2
+	subs	r0, r0, #1		@ Set--
+	bpl	2b
+	subs	r3, r3, r1		@ Way--
+	bcc	3f
+	mrc	p15, 1, r0, c0, c0, 0	@ re-read cache geometry from CCSIDR
+	b	1b
+3:	dsb	st
+	isb
+	ret	lr
 ENDPROC(v7_invalidate_l1)
 
 /*
Signature · 1 line
2.30.2
author maintainer
#402 lore raw

PATCH 402/425 PCI: thunder: Fix compile testing

In reply to Greg Kroah-Hartman

From: Arnd Bergmann <[email protected]>

[ Upstream commit 16f7ae5906dfbeff54f74ec75d0563bb3a87ab0b ]

Compile-testing these drivers is currently broken. Enabling it causes a couple of build failures though:

drivers/pci/controller/pci-thunder-ecam.c:119:30: error: shift count >= width of type [-Werror,-Wshift-count-overflow] drivers/pci/controller/pci-thunder-pem.c:54:2: error: implicit declaration of function 'writeq' [-Werror,-Wimplicit-function-declaration] drivers/pci/controller/pci-thunder-pem.c:392:8: error: implicit declaration of function 'acpi_get_rc_resources' [-Werror,-Wimplicit-function-declaration]

Fix them with the obvious one-line changes.

---
 drivers/pci/controller/pci-thunder-ecam.c |  2 +-
 drivers/pci/controller/pci-thunder-pem.c  | 13 +++++++------
 drivers/pci/pci.h                         |  6 ++++++
 3 files changed, 14 insertions(+), 7 deletions(-)
drivers/pci/controller/pci-thunder-ecam.c +1 -1
index 32d1d7b81ef4..18715d2ce022 100644
@@ -116,7 +116,7 @@ static int thunder_ecam_p2_config_read(struct pci_bus *bus, unsigned int devfn,
 	 * the config space access window.  Since we are working with
 	 * the high-order 32 bits, shift everything down by 32 bits.
 	 */
-	node_bits = (cfg->res.start >> 32) & (1 << 12);
+	node_bits = upper_32_bits(cfg->res.start) & (1 << 12);
 
 	v |= node_bits;
 	set_val(v, where, size, val);
drivers/pci/controller/pci-thunder-pem.c +7 -6
index f127ce8bd4ef..1650ec2c35f9 100644
@@ -11,6 +11,7 @@
 #include <linux/pci-acpi.h>
 #include <linux/pci-ecam.h>
 #include <linux/platform_device.h>
+#include <linux/io-64-nonatomic-lo-hi.h>
 #include "../pci.h"
 
 #if defined(CONFIG_PCI_HOST_THUNDER_PEM) || (defined(CONFIG_ACPI) && defined(CONFIG_PCI_QUIRKS))
@@ -314,9 +315,9 @@ static int thunder_pem_init(struct device *dev, struct pci_config_window *cfg,
 	 * structure here for the BAR.
 	 */
 	bar4_start = res_pem->start + 0xf00000;
-	pem_pci->ea_entry[0] = (u32)bar4_start | 2;
-	pem_pci->ea_entry[1] = (u32)(res_pem->end - bar4_start) & ~3u;
-	pem_pci->ea_entry[2] = (u32)(bar4_start >> 32);
+	pem_pci->ea_entry[0] = lower_32_bits(bar4_start) | 2;
+	pem_pci->ea_entry[1] = lower_32_bits(res_pem->end - bar4_start) & ~3u;
+	pem_pci->ea_entry[2] = upper_32_bits(bar4_start);
 
 	cfg->priv = pem_pci;
 	return 0;
@@ -324,9 +325,9 @@ static int thunder_pem_init(struct device *dev, struct pci_config_window *cfg,
 
 #if defined(CONFIG_ACPI) && defined(CONFIG_PCI_QUIRKS)
 
-#define PEM_RES_BASE		0x87e0c0000000UL
-#define PEM_NODE_MASK		GENMASK(45, 44)
-#define PEM_INDX_MASK		GENMASK(26, 24)
+#define PEM_RES_BASE		0x87e0c0000000ULL
+#define PEM_NODE_MASK		GENMASK_ULL(45, 44)
+#define PEM_INDX_MASK		GENMASK_ULL(26, 24)
 #define PEM_MIN_DOM_IN_NODE	4
 #define PEM_MAX_DOM_IN_NODE	10
 
drivers/pci/pci.h +6 -0
index e9ede82ee2c2..39725b71300f 100644
@@ -473,6 +473,12 @@ static inline int pci_dev_specific_reset(struct pci_dev *dev, int probe)
 #if defined(CONFIG_PCI_QUIRKS) && defined(CONFIG_ARM64)
 int acpi_get_rc_resources(struct device *dev, const char *hid, u16 segment,
 			  struct resource *res);
+#else
+static inline int acpi_get_rc_resources(struct device *dev, const char *hid,
+					u16 segment, struct resource *res)
+{
+	return -ENODEV;
+}
 #endif
 
 u32 pci_rebar_get_possible_sizes(struct pci_dev *pdev, int bar);
Signature · 1 line
2.30.2
author maintainer
#403 lore raw

PATCH 403/425 ARM: 9066/1: ftrace: pause/unpause function graph tracer in cpu_suspend()

In reply to Greg Kroah-Hartman

From: louis.wang <[email protected]>

[ Upstream commit 8252ca87c7a2111502ee13994956f8c309faad7f ]

Enabling function_graph tracer on ARM causes kernel panic, because the function graph tracer updates the "return address" of a function in order to insert a trace callback on function exit, it saves the function's original return address in a return trace stack, but cpu_suspend() may not return through the normal return path.

cpu_suspend() will resume directly via the cpu_resume path, but the return trace stack has been set-up by the subfunctions of cpu_suspend(), which makes the "return address" inconsistent with cpu_suspend().

This patch refers to Commit de818bd4522c40ea02a81b387d2fa86f989c9623 ("arm64: kernel: pause/unpause function graph tracer in cpu_suspend()"),

fixes the issue by pausing/resuming the function graph tracer on the thread executing cpu_suspend(), so that the function graph tracer state is kept consistent across functions that enter power down states and never return by effectively disabling graph tracer while they are executing.

---
 arch/arm/kernel/suspend.c | 19 ++++++++++++++++++-
 1 file changed, 18 insertions(+), 1 deletion(-)
arch/arm/kernel/suspend.c +18 -1
index d08099269e35..e126386fb78a 100644
@@ -1,4 +1,5 @@
 // SPDX-License-Identifier: GPL-2.0
+#include <linux/ftrace.h>
 #include <linux/init.h>
 #include <linux/slab.h>
 #include <linux/mm_types.h>
@@ -26,6 +27,13 @@ int cpu_suspend(unsigned long arg, int (*fn)(unsigned long))
 	if (!idmap_pgd)
 		return -EINVAL;
 
+	/*
+	 * Function graph tracer state gets incosistent when the kernel
+	 * calls functions that never return (aka suspend finishers) hence
+	 * disable graph tracing during their execution.
+	 */
+	pause_graph_tracing();
+
 	/*
 	 * Provide a temporary page table with an identity mapping for
 	 * the MMU-enable code, required for resuming.  On successful
@@ -33,6 +41,9 @@ int cpu_suspend(unsigned long arg, int (*fn)(unsigned long))
 	 * back to the correct page tables.
 	 */
 	ret = __cpu_suspend(arg, fn, __mpidr);
+
+	unpause_graph_tracing();
+
 	if (ret == 0) {
 		cpu_switch_mm(mm->pgd, mm);
 		local_flush_bp_all();
@@ -46,7 +57,13 @@ int cpu_suspend(unsigned long arg, int (*fn)(unsigned long))
 int cpu_suspend(unsigned long arg, int (*fn)(unsigned long))
 {
 	u32 __mpidr = cpu_logical_map(smp_processor_id());
-	return __cpu_suspend(arg, fn, __mpidr);
+	int ret;
+
+	pause_graph_tracing();
+	ret = __cpu_suspend(arg, fn, __mpidr);
+	unpause_graph_tracing();
+
+	return ret;
 }
 #define	idmap_pgd	NULL
 #endif
Signature · 1 line
2.30.2
author maintainer
#404 lore raw

PATCH 404/425 ACPI / hotplug / PCI: Fix reference count leak in enable_slot()

In reply to Greg Kroah-Hartman

From: Feilong Lin <[email protected]>

[ Upstream commit 3bbfd319034ddce59e023837a4aa11439460509b ]

In enable_slot(), if pci_get_slot() returns NULL, we clear the SLOT_ENABLED flag. When pci_get_slot() finds a device, it increments the device's reference count. In this case, we did not call pci_dev_put() to decrement the reference count, so the memory of the device (struct pci_dev type) will eventually leak.

Call pci_dev_put() to decrement its reference count when pci_get_slot() returns a PCI device.

---
 drivers/pci/hotplug/acpiphp_glue.c | 1 +
 1 file changed, 1 insertion(+)
drivers/pci/hotplug/acpiphp_glue.c +1 -0
index be35bbfa6968..3d8844e7090a 100644
@@ -540,6 +540,7 @@ static void enable_slot(struct acpiphp_slot *slot, bool bridge)
 			slot->flags &= ~SLOT_ENABLED;
 			continue;
 		}
+		pci_dev_put(dev);
 	}
 }
 
Signature · 1 line
2.30.2
author maintainer
#405 lore raw

PATCH 405/425 Input: elants_i2c - do not bind to i2c-hid compatible ACPI instantiated devices

In reply to Greg Kroah-Hartman

From: Hans de Goede <[email protected]>

[ Upstream commit 65299e8bfb24774e6340e93ae49f6626598917c8 ]

Several users have been reporting that elants_i2c gives several errors during probe and that their touchscreen does not work on their Lenovo AMD based laptops with a touchscreen with a ELAN0001 ACPI hardware-id:

[    0.550596] elants_i2c i2c-ELAN0001:00: i2c-ELAN0001:00 supply vcc33 not found, using dummy regulator
[    0.551836] elants_i2c i2c-ELAN0001:00: i2c-ELAN0001:00 supply vccio not found, using dummy regulator
[    0.560932] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[    0.562427] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[    0.595925] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[    0.597974] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[    0.621893] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[    0.622504] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[    0.632650] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (4d 61 69 6e): -121
[    0.634256] elants_i2c i2c-ELAN0001:00: boot failed: -121
[    0.699212] elants_i2c i2c-ELAN0001:00: invalid 'hello' packet: 00 00 ff ff
[    1.630506] elants_i2c i2c-ELAN0001:00: Failed to read fw id: -121
[    1.645508] elants_i2c i2c-ELAN0001:00: unknown packet 00 00 ff ff

Despite these errors, the elants_i2c driver stays bound to the device (it returns 0 from its probe method despite the errors), blocking the i2c-hid driver from binding.

Manually unbinding the elants_i2c driver and binding the i2c-hid driver makes the touchscreen work.

Check if the ACPI-fwnode for the touchscreen contains one of the i2c-hid compatiblity-id strings and if it has the I2C-HID spec's DSM to get the HID descriptor address, If it has both then make elants_i2c not bind, so that the i2c-hid driver can bind.

This assumes that non of the (older) elan touchscreens which actually need the elants_i2c driver falsely advertise an i2c-hid compatiblity-id
+ DSM in their ACPI-fwnodes. If some of them actually do have this false advertising, then this change may lead to regressions.

While at it also drop the unnecessary DEVICE_NAME prefixing of the "I2C check functionality error", dev_err already outputs the driver-name.

---
 drivers/input/touchscreen/elants_i2c.c | 44 ++++++++++++++++++++++++--
 1 file changed, 42 insertions(+), 2 deletions(-)
drivers/input/touchscreen/elants_i2c.c +42 -2
index d21ca39b0fdb..adfae2d88707 100644
@@ -41,6 +41,7 @@
 #include <linux/of.h>
 #include <linux/gpio/consumer.h>
 #include <linux/regulator/consumer.h>
+#include <linux/uuid.h>
 #include <asm/unaligned.h>
 
 /* Device, Driver information */
@@ -1131,6 +1132,40 @@ static void elants_i2c_power_off(void *_data)
 	}
 }
 
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id i2c_hid_ids[] = {
+	{"ACPI0C50", 0 },
+	{"PNP0C50", 0 },
+	{ },
+};
+
+static const guid_t i2c_hid_guid =
+	GUID_INIT(0x3CDFF6F7, 0x4267, 0x4555,
+		  0xAD, 0x05, 0xB3, 0x0A, 0x3D, 0x89, 0x38, 0xDE);
+
+static bool elants_acpi_is_hid_device(struct device *dev)
+{
+	acpi_handle handle = ACPI_HANDLE(dev);
+	union acpi_object *obj;
+
+	if (acpi_match_device_ids(ACPI_COMPANION(dev), i2c_hid_ids))
+		return false;
+
+	obj = acpi_evaluate_dsm_typed(handle, &i2c_hid_guid, 1, 1, NULL, ACPI_TYPE_INTEGER);
+	if (obj) {
+		ACPI_FREE(obj);
+		return true;
+	}
+
+	return false;
+}
+#else
+static bool elants_acpi_is_hid_device(struct device *dev)
+{
+	return false;
+}
+#endif
+
 static int elants_i2c_probe(struct i2c_client *client,
 			    const struct i2c_device_id *id)
 {
@@ -1139,9 +1174,14 @@ static int elants_i2c_probe(struct i2c_client *client,
 	unsigned long irqflags;
 	int error;
 
+	/* Don't bind to i2c-hid compatible devices, these are handled by the i2c-hid drv. */
+	if (elants_acpi_is_hid_device(&client->dev)) {
+		dev_warn(&client->dev, "This device appears to be an I2C-HID device, not binding\n");
+		return -ENODEV;
+	}
+
 	if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
-		dev_err(&client->dev,
-			"%s: i2c check functionality error\n", DEVICE_NAME);
+		dev_err(&client->dev, "I2C check functionality error\n");
 		return -ENXIO;
 	}
 
Signature · 1 line
2.30.2
author maintainer
#406 lore raw

PATCH 406/425 Input: silead - add workaround for x86 BIOS-es which bring the chip up in a stuck state

In reply to Greg Kroah-Hartman

From: Hans de Goede <[email protected]>

[ Upstream commit e479187748a8f151a85116a7091c599b121fdea5 ]

Some buggy BIOS-es bring up the touchscreen-controller in a stuck state where it blocks the I2C bus. Specifically this happens on the Jumper EZpad 7 tablet model.

After much poking at this problem I have found that the following steps are necessary to unstuck the chip / bus:

1. Turn off the Silead chip.
2. Try to do an I2C transfer with the chip, this will fail in response to which the I2C-bus-driver will call: i2c_recover_bus() which will unstuck the I2C-bus. Note the unstuck-ing of the I2C bus only works if we first drop the chip of the bus by turning it off.
3. Turn the chip back on.

On the x86/ACPI systems were this problem is seen, step 1. and 3. require making ACPI calls and dealing with ACPI Power Resources. This commit adds a workaround which runtime-suspends the chip to turn it off, leaving it up to the ACPI subsystem to deal with all the ACPI specific details.

There is no good way to detect this bug, so the workaround gets activated by a new "silead,stuck-controller-bug" boolean device-property. Since this is only used on x86/ACPI, this will be set by model specific device-props set by drivers/platform/x86/touchscreen_dmi.c. Therefor this new device-property is not documented in the DT-bindings.

Dmesg will contain the following messages on systems where the workaround is activated:

[   54.309029] silead_ts i2c-MSSL1680:00: [Firmware Bug]: Stuck I2C bus: please ignore the next 'controller timed out' error
[   55.373593] i2c_designware 808622C1:04: controller timed out
[   55.582186] silead_ts i2c-MSSL1680:00: Silead chip ID: 0x80360000
---
 drivers/input/touchscreen/silead.c | 44 +++++++++++++++++++++++++++---
 1 file changed, 40 insertions(+), 4 deletions(-)
drivers/input/touchscreen/silead.c +40 -4
index 06f0eb04a8fd..a787a6aefc69 100644
@@ -28,6 +28,7 @@
 #include <linux/input/mt.h>
 #include <linux/input/touchscreen.h>
 #include <linux/pm.h>
+#include <linux/pm_runtime.h>
 #include <linux/irq.h>
 #include <linux/regulator/consumer.h>
 
@@ -343,10 +344,8 @@ static int silead_ts_get_id(struct i2c_client *client)
 
 	error = i2c_smbus_read_i2c_block_data(client, SILEAD_REG_ID,
 					      sizeof(chip_id), (u8 *)&chip_id);
-	if (error < 0) {
-		dev_err(&client->dev, "Chip ID read error %d\n", error);
+	if (error < 0)
 		return error;
-	}
 
 	data->chip_id = le32_to_cpu(chip_id);
 	dev_info(&client->dev, "Silead chip ID: 0x%8X", data->chip_id);
@@ -359,12 +358,49 @@ static int silead_ts_setup(struct i2c_client *client)
 	int error;
 	u32 status;
 
+	/*
+	 * Some buggy BIOS-es bring up the chip in a stuck state where it
+	 * blocks the I2C bus. The following steps are necessary to
+	 * unstuck the chip / bus:
+	 * 1. Turn off the Silead chip.
+	 * 2. Try to do an I2C transfer with the chip, this will fail in
+	 *    response to which the I2C-bus-driver will call:
+	 *    i2c_recover_bus() which will unstuck the I2C-bus. Note the
+	 *    unstuck-ing of the I2C bus only works if we first drop the
+	 *    chip off the bus by turning it off.
+	 * 3. Turn the chip back on.
+	 *
+	 * On the x86/ACPI systems were this problem is seen, step 1. and
+	 * 3. require making ACPI calls and dealing with ACPI Power
+	 * Resources. The workaround below runtime-suspends the chip to
+	 * turn it off, leaving it up to the ACPI subsystem to deal with
+	 * this.
+	 */
+
+	if (device_property_read_bool(&client->dev,
+				      "silead,stuck-controller-bug")) {
+		pm_runtime_set_active(&client->dev);
+		pm_runtime_enable(&client->dev);
+		pm_runtime_allow(&client->dev);
+
+		pm_runtime_suspend(&client->dev);
+
+		dev_warn(&client->dev, FW_BUG "Stuck I2C bus: please ignore the next 'controller timed out' error\n");
+		silead_ts_get_id(client);
+
+		/* The forbid will also resume the device */
+		pm_runtime_forbid(&client->dev);
+		pm_runtime_disable(&client->dev);
+	}
+
 	silead_ts_set_power(client, SILEAD_POWER_OFF);
 	silead_ts_set_power(client, SILEAD_POWER_ON);
 
 	error = silead_ts_get_id(client);
-	if (error)
+	if (error) {
+		dev_err(&client->dev, "Chip ID read error %d\n", error);
 		return error;
+	}
 
 	error = silead_ts_init(client);
 	if (error)
Signature · 1 line
2.30.2
author maintainer
#407 lore raw

PATCH 407/425 um: Mark all kernel symbols as local

In reply to Greg Kroah-Hartman

From: Johannes Berg <[email protected]>

[ Upstream commit d5027ca63e0e778b641cf23e3f5c6d6212cf412b ]

Ritesh reported a bug [1] against UML, noting that it crashed on startup. The backtrace shows the following (heavily redacted):

(gdb) bt
...
#26 0x0000000060015b5d in sem_init () at ipc/sem.c:268
#27 0x00007f89906d92f7 in ?? () from /lib/x86_64-linux-gnu/libcom_err.so.2 #28 0x00007f8990ab8fb2 in call_init (...) at dl-init.c:72
...
#40 0x00007f89909bf3a6 in nss_load_library (...) at nsswitch.c:359
...
#44 0x00007f8990895e35 in _nss_compat_getgrnam_r (...) at nss_compat/compat-grp.c:486 #45 0x00007f8990968b85 in __getgrnam_r [...]
#46 0x00007f89909d6b77 in grantpt [...]
#47 0x00007f8990a9394e in __GI_openpty [...]
#48 0x00000000604a1f65 in openpty_cb (...) at arch/um/os-Linux/sigio.c:407 #49 0x00000000604a58d0 in start_idle_thread (...) at arch/um/os-Linux/skas/process.c:598 #50 0x0000000060004a3d in start_uml () at arch/um/kernel/skas/process.c:45 #51 0x00000000600047b2 in linux_main (...) at arch/um/kernel/um_arch.c:334 #52 0x000000006000574f in main (...) at arch/um/os-Linux/main.c:144

indicating that the UML function openpty_cb() calls openpty(), which internally calls __getgrnam_r(), which causes the nsswitch machinery to get started.

This loads, through lots of indirection that I snipped, the libcom_err.so.2 library, which (in an unknown function, "??") calls sem_init().

Now, of course it wants to get libpthread's sem_init(), since it's linked against libpthread. However, the dynamic linker looks up that symbol against the binary first, and gets the kernel's sem_init().

Hajime Tazaki noted that "objcopy -L" can localize a symbol, so the dynamic linker wouldn't do the lookup this way. I tried, but for some reason that didn't seem to work.

Doing the same thing in the linker script instead does seem to work, though I cannot entirely explain - it *also* works if I just add "VERSION { { global: *; }; }" instead, indicating that something else is happening that I don't really understand. It may be that explicitly doing that marks them with some kind of empty version, and that's different from the default.

Explicitly marking them with a version breaks kallsyms, so that doesn't seem to be possible.

Marking all the symbols as local seems correct, and does seem to address the issue, so do that. Also do it for static link, nsswitch libraries could still be loaded there.

[1] https://bugs.debian.org/983379

---
 arch/um/kernel/dyn.lds.S | 6 ++++++
 arch/um/kernel/uml.lds.S | 6 ++++++
 2 files changed, 12 insertions(+)
arch/um/kernel/dyn.lds.S +6 -0
index 5568cf882371..899233625467 100644
@@ -6,6 +6,12 @@ OUTPUT_ARCH(ELF_ARCH)
 ENTRY(_start)
 jiffies = jiffies_64;
 
+VERSION {
+  {
+    local: *;
+  };
+}
+
 SECTIONS
 {
   PROVIDE (__executable_start = START);
arch/um/kernel/uml.lds.S +6 -0
index 36b07ec09742..22ff701d9b71 100644
@@ -7,6 +7,12 @@ OUTPUT_ARCH(ELF_ARCH)
 ENTRY(_start)
 jiffies = jiffies_64;
 
+VERSION {
+  {
+    local: *;
+  };
+}
+
 SECTIONS
 {
   /* This must contain the right address - not quite the default ELF one.*/
Signature · 1 line
2.30.2
author maintainer
#408 lore raw

PATCH 408/425 ARM: 9075/1: kernel: Fix interrupted SMC calls

In reply to Greg Kroah-Hartman

From: Manivannan Sadhasivam <[email protected]>

[ Upstream commit 57ac51667d8cd62731223d687e5fe7b41c502f89 ]

On Qualcomm ARM32 platforms, the SMC call can return before it has completed. If this occurs, the call can be restarted, but it requires using the returned session ID value from the interrupted SMC call.

The ARM32 SMCC code already has the provision to add platform specific quirks for things like this. So let's make use of it and add the Qualcomm specific quirk (ARM_SMCCC_QUIRK_QCOM_A6) used by the QCOM_SCM driver.

This change is similar to the below one added for ARM64 a while ago:
commit 82bcd087029f ("firmware: qcom: scm: Fix interrupted SCM calls")

Without this change, the Qualcomm ARM32 platforms like SDX55 will return -EINVAL for SMC calls used for modem firmware loading and validation.

---
 arch/arm/kernel/asm-offsets.c |  3 +++
 arch/arm/kernel/smccc-call.S  | 11 ++++++++++-
 2 files changed, 13 insertions(+), 1 deletion(-)
arch/arm/kernel/asm-offsets.c +3 -0
index ae85f67a6352..40afe953a0e2 100644
@@ -30,6 +30,7 @@
 #include <asm/vdso_datapage.h>
 #include <asm/hardware/cache-l2x0.h>
 #include <linux/kbuild.h>
+#include <linux/arm-smccc.h>
 #include "signal.h"
 
 /*
@@ -159,6 +160,8 @@ int main(void)
   DEFINE(SLEEP_SAVE_SP_PHYS,	offsetof(struct sleep_save_sp, save_ptr_stash_phys));
   DEFINE(SLEEP_SAVE_SP_VIRT,	offsetof(struct sleep_save_sp, save_ptr_stash));
 #endif
+  DEFINE(ARM_SMCCC_QUIRK_ID_OFFS,	offsetof(struct arm_smccc_quirk, id));
+  DEFINE(ARM_SMCCC_QUIRK_STATE_OFFS,	offsetof(struct arm_smccc_quirk, state));
   BLANK();
   DEFINE(DMA_BIDIRECTIONAL,	DMA_BIDIRECTIONAL);
   DEFINE(DMA_TO_DEVICE,		DMA_TO_DEVICE);
arch/arm/kernel/smccc-call.S +10 -1
index e5d43066b889..13d307cd364c 100644
@@ -12,7 +12,9 @@
  *
  */
 #include <linux/linkage.h>
+#include <linux/arm-smccc.h>
 
+#include <asm/asm-offsets.h>
 #include <asm/opcodes-sec.h>
 #include <asm/opcodes-virt.h>
 #include <asm/unwind.h>
@@ -36,7 +38,14 @@ UNWIND(	.fnstart)
 UNWIND(	.save	{r4-r7})
 	ldm	r12, {r4-r7}
 	\instr
-	pop	{r4-r7}
+	ldr	r4, [sp, #36]
+	cmp	r4, #0
+	beq	1f			// No quirk structure
+	ldr     r5, [r4, #ARM_SMCCC_QUIRK_ID_OFFS]
+	cmp     r5, #ARM_SMCCC_QUIRK_QCOM_A6
+	bne	1f			// No quirk present
+	str	r6, [r4, #ARM_SMCCC_QUIRK_STATE_OFFS]
+1:	pop	{r4-r7}
 	ldr	r12, [sp, #(4 * 4)]
 	stm	r12, {r0-r3}
 	bx	lr
Signature · 1 line
2.30.2
author maintainer
#409 lore raw

PATCH 409/425 scripts/recordmcount.pl: Fix RISC-V regex for clang

In reply to Greg Kroah-Hartman

From: Nathan Chancellor <[email protected]>

[ Upstream commit 2f095504f4b9cf75856d6a9cf90299cf75aa46c5 ]

Clang can generate R_RISCV_CALL_PLT relocations to _mcount:

$ llvm-objdump -dr build/riscv/init/main.o | rg mcount
                000000000000000e:  R_RISCV_CALL_PLT     _mcount
                000000000000004e:  R_RISCV_CALL_PLT     _mcount

After this, the __start_mcount_loc section is properly generated and function tracing still works.

---
 scripts/recordmcount.pl | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
scripts/recordmcount.pl +1 -1
index 9a8fe8ea6b03..bc12e12e4b3a 100755
@@ -395,7 +395,7 @@ if ($arch eq "x86_64") {
     $mcount_regex = "^\\s*([0-9a-fA-F]+):.*\\s_mcount\$";
 } elsif ($arch eq "riscv") {
     $function_regex = "^([0-9a-fA-F]+)\\s+<([^.0-9][0-9a-zA-Z_\\.]+)>:";
-    $mcount_regex = "^\\s*([0-9a-fA-F]+):\\sR_RISCV_CALL\\s_mcount\$";
+    $mcount_regex = "^\\s*([0-9a-fA-F]+):\\sR_RISCV_CALL(_PLT)?\\s_mcount\$";
     $type = ".quad";
     $alignment = 2;
 } elsif ($arch eq "nds32") {
Signature · 1 line
2.30.2
author maintainer
#410 lore raw

PATCH 410/425 riscv: Workaround mcount name prior to clang-13

In reply to Greg Kroah-Hartman

From: Nathan Chancellor <[email protected]>

[ Upstream commit 7ce04771503074a7de7f539cc43f5e1b385cb99b ]

Prior to clang 13.0.0, the RISC-V name for the mcount symbol was "mcount", which differs from the GCC version of "_mcount", which results in the following errors:

riscv64-linux-gnu-ld: init/main.o: in function `__traceiter_initcall_level':
main.c:(.text+0xe): undefined reference to `mcount'
riscv64-linux-gnu-ld: init/main.o: in function `__traceiter_initcall_start':
main.c:(.text+0x4e): undefined reference to `mcount'
riscv64-linux-gnu-ld: init/main.o: in function `__traceiter_initcall_finish':
main.c:(.text+0x92): undefined reference to `mcount'
riscv64-linux-gnu-ld: init/main.o: in function `.LBB32_28':
main.c:(.text+0x30c): undefined reference to `mcount'
riscv64-linux-gnu-ld: init/main.o: in function `free_initmem':
main.c:(.text+0x54c): undefined reference to `mcount'

This has been corrected in https://reviews.llvm.org/D98881 but the minimum supported clang version is 10.0.1. To avoid build errors and to gain a working function tracer, adjust the name of the mcount symbol for older versions of clang in mount.S and recordmcount.pl.

---
 arch/riscv/include/asm/ftrace.h | 14 ++++++++++++--
 arch/riscv/kernel/mcount.S      | 10 +++++-----
 scripts/recordmcount.pl         |  2 +-
 3 files changed, 18 insertions(+), 8 deletions(-)
arch/riscv/include/asm/ftrace.h +12 -2
index 02fbc175142e..693c3839a7df 100644
@@ -10,9 +10,19 @@
 #endif
 #define HAVE_FUNCTION_GRAPH_RET_ADDR_PTR
 
+/*
+ * Clang prior to 13 had "mcount" instead of "_mcount":
+ * https://reviews.llvm.org/D98881
+ */
+#if defined(CONFIG_CC_IS_GCC) || CONFIG_CLANG_VERSION >= 130000
+#define MCOUNT_NAME _mcount
+#else
+#define MCOUNT_NAME mcount
+#endif
+
 #define ARCH_SUPPORTS_FTRACE_OPS 1
 #ifndef __ASSEMBLY__
-void _mcount(void);
+void MCOUNT_NAME(void);
 static inline unsigned long ftrace_call_adjust(unsigned long addr)
 {
 	return addr;
@@ -33,7 +43,7 @@ struct dyn_arch_ftrace {
  * both auipc and jalr at the same time.
  */
 
-#define MCOUNT_ADDR		((unsigned long)_mcount)
+#define MCOUNT_ADDR		((unsigned long)MCOUNT_NAME)
 #define JALR_SIGN_MASK		(0x00000800)
 #define JALR_OFFSET_MASK	(0x00000fff)
 #define AUIPC_OFFSET_MASK	(0xfffff000)
arch/riscv/kernel/mcount.S +5 -5
index 5721624886a1..fabddee90d1b 100644
@@ -47,8 +47,8 @@
 
 ENTRY(ftrace_stub)
 #ifdef CONFIG_DYNAMIC_FTRACE
-       .global _mcount
-       .set    _mcount, ftrace_stub
+       .global MCOUNT_NAME
+       .set    MCOUNT_NAME, ftrace_stub
 #endif
 	ret
 ENDPROC(ftrace_stub)
@@ -79,7 +79,7 @@ EXPORT_SYMBOL(return_to_handler)
 #endif
 
 #ifndef CONFIG_DYNAMIC_FTRACE
-ENTRY(_mcount)
+ENTRY(MCOUNT_NAME)
 	la	t4, ftrace_stub
 #ifdef CONFIG_FUNCTION_GRAPH_TRACER
 	la	t0, ftrace_graph_return
@@ -125,6 +125,6 @@ do_trace:
 	jalr	t5
 	RESTORE_ABI_STATE
 	ret
-ENDPROC(_mcount)
+ENDPROC(MCOUNT_NAME)
 #endif
-EXPORT_SYMBOL(_mcount)
+EXPORT_SYMBOL(MCOUNT_NAME)
scripts/recordmcount.pl +1 -1
index bc12e12e4b3a..657e69125a46 100755
@@ -395,7 +395,7 @@ if ($arch eq "x86_64") {
     $mcount_regex = "^\\s*([0-9a-fA-F]+):.*\\s_mcount\$";
 } elsif ($arch eq "riscv") {
     $function_regex = "^([0-9a-fA-F]+)\\s+<([^.0-9][0-9a-zA-Z_\\.]+)>:";
-    $mcount_regex = "^\\s*([0-9a-fA-F]+):\\sR_RISCV_CALL(_PLT)?\\s_mcount\$";
+    $mcount_regex = "^\\s*([0-9a-fA-F]+):\\sR_RISCV_CALL(_PLT)?\\s_?mcount\$";
     $type = ".quad";
     $alignment = 2;
 } elsif ($arch eq "nds32") {
Signature · 1 line
2.30.2
author maintainer
#411 lore raw

PATCH 411/425 ceph: fix fscache invalidation

In reply to Greg Kroah-Hartman

From: Jeff Layton <[email protected]>

[ Upstream commit 10a7052c7868bc7bc72d947f5aac6f768928db87 ]

Ensure that we invalidate the fscache whenever we invalidate the pagecache.

---
 fs/ceph/caps.c  | 1 +
 fs/ceph/inode.c | 1 +
 2 files changed, 2 insertions(+)
fs/ceph/caps.c +1 -0
index 6e871a382209..918781c51f0b 100644
@@ -1779,6 +1779,7 @@ static int try_nonblocking_invalidate(struct inode *inode)
 	u32 invalidating_gen = ci->i_rdcache_gen;
 
 	spin_unlock(&ci->i_ceph_lock);
+	ceph_fscache_invalidate(inode);
 	invalidate_mapping_pages(&inode->i_data, 0, -1);
 	spin_lock(&ci->i_ceph_lock);
 
fs/ceph/inode.c +1 -0
index 3c24fb77ef32..5f041fede7aa 100644
@@ -1823,6 +1823,7 @@ static void ceph_invalidate_work(struct work_struct *work)
 	orig_gen = ci->i_rdcache_gen;
 	spin_unlock(&ci->i_ceph_lock);
 
+	ceph_fscache_invalidate(inode);
 	if (invalidate_inode_pages2(inode->i_mapping) < 0) {
 		pr_err("invalidate_pages %p fails\n", inode);
 	}
Signature · 1 line
2.30.2
author maintainer
#412 lore raw

PATCH 412/425 scsi: target: tcmu: Return from tcmu_handle_completions() if cmd_id not found

In reply to Greg Kroah-Hartman

From: Bodo Stroesser <[email protected]>

[ Upstream commit 9814b55cde0588b6d9bc496cee43f87316cbc6f1 ]

If tcmu_handle_completions() finds an invalid cmd_id while looping over cmd responses from userspace it sets TCMU_DEV_BIT_BROKEN and breaks the loop. This means that it does further handling for the tcmu device.

Skip that handling by replacing 'break' with 'return'.

Additionally change tcmu_handle_completions() from unsigned int to bool, since the value used in return already is bool.

---
 drivers/target/target_core_user.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/target/target_core_user.c +2 -2
index 0219b5a865be..dd7307375504 100644
@@ -1216,7 +1216,7 @@ static void tcmu_set_next_deadline(struct list_head *queue,
 		del_timer(timer);
 }
 
-static unsigned int tcmu_handle_completions(struct tcmu_dev *udev)
+static bool tcmu_handle_completions(struct tcmu_dev *udev)
 {
 	struct tcmu_mailbox *mb;
 	struct tcmu_cmd *cmd;
@@ -1256,7 +1256,7 @@ static unsigned int tcmu_handle_completions(struct tcmu_dev *udev)
 			pr_err("cmd_id %u not found, ring is broken\n",
 			       entry->hdr.cmd_id);
 			set_bit(TCMU_DEV_BIT_BROKEN, &udev->flags);
-			break;
+			return false;
 		}
 
 		tcmu_handle_completion(cmd, entry);
Signature · 1 line
2.30.2
author maintainer
#413 lore raw

PATCH 413/425 gpiolib: acpi: Add quirk to ignore EC wakeups on Dell Venue 10 Pro 5055

In reply to Greg Kroah-Hartman

From: Hans de Goede <[email protected]>

[ Upstream commit da91ece226729c76f60708efc275ebd4716ad089 ]

Like some other Bay and Cherry Trail SoC based devices the Dell Venue 10 Pro 5055 has an embedded-controller which uses ACPI GPIO events to report events instead of using the standard ACPI EC interface for this.

The EC interrupt is only used to report battery-level changes and it keeps doing this while the system is suspended, causing the system to not stay suspended.

Add an ignore-wake quirk for the GPIO pin used by the EC to fix the spurious wakeups from suspend.

---
 drivers/gpio/gpiolib-acpi.c | 14 ++++++++++++++
 1 file changed, 14 insertions(+)
drivers/gpio/gpiolib-acpi.c +14 -0
index 4ad34c6803ad..b018909a4e46 100644
@@ -1355,6 +1355,20 @@ static const struct dmi_system_id gpiolib_acpi_quirks[] = {
 			.no_edge_events_on_boot = true,
 		},
 	},
+	{
+		/*
+		 * The Dell Venue 10 Pro 5055, with Bay Trail SoC + TI PMIC uses an
+		 * external embedded-controller connected via I2C + an ACPI GPIO
+		 * event handler on INT33FFC:02 pin 12, causing spurious wakeups.
+		 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Venue 10 Pro 5055"),
+		},
+		.driver_data = &(struct acpi_gpiolib_dmi_quirk) {
+			.ignore_wake = "INT33FC:02@12",
+		},
+	},
 	{
 		/*
 		 * HP X2 10 models with Cherry Trail SoC + TI PMIC use an
Signature · 1 line
2.30.2
author maintainer
#414 lore raw

PATCH 414/425 ALSA: hda: generic: change the DAC ctl name for LO+SPK or LO+HP

In reply to Greg Kroah-Hartman

From: Hui Wang <[email protected]>

[ Upstream commit f48652bbe3ae62ba2835a396b7e01f063e51c4cd ]

Without this change, the DAC ctl's name could be changed only when the machine has both Speaker and Headphone, but we met some machines which only has Lineout and Headhpone, and the Lineout and Headphone share the Audio Mixer0 and DAC0, the ctl's name is set to "Front".

On most of machines, the "Front" is used for Speaker only or Lineout only, but on this machine it is shared by Lineout and Headphone, This introduces an issue in the pipewire and pulseaudio, suppose users want the Headphone to be on and the Speaker/Lineout to be off, they could turn off the "Front", this works on most of the machines, but on this machine, the "Front" couldn't be turned off otherwise the headphone will be off too. Here we do some change to let the ctl's name change to "Headphone+LO" on this machine, and pipewire and pulseaudio already could handle "Headphone+LO" and "Speaker+LO".
(https://gitlab.freedesktop.org/pipewire/pipewire/-/issues/747)

---
 sound/pci/hda/hda_generic.c | 16 +++++++++++-----
 1 file changed, 11 insertions(+), 5 deletions(-)
sound/pci/hda/hda_generic.c +11 -5
index b9f7b23ae378..6099a9f1cb3d 100644
@@ -1214,11 +1214,17 @@ static const char *get_line_out_pfx(struct hda_codec *codec, int ch,
 		*index = ch;
 		return "Headphone";
 	case AUTO_PIN_LINE_OUT:
-		/* This deals with the case where we have two DACs and
-		 * one LO, one HP and one Speaker */
-		if (!ch && cfg->speaker_outs && cfg->hp_outs) {
-			bool hp_lo_shared = !path_has_mixer(codec, spec->hp_paths[0], ctl_type);
-			bool spk_lo_shared = !path_has_mixer(codec, spec->speaker_paths[0], ctl_type);
+		/* This deals with the case where one HP or one Speaker or
+		 * one HP + one Speaker need to share the DAC with LO
+		 */
+		if (!ch) {
+			bool hp_lo_shared = false, spk_lo_shared = false;
+
+			if (cfg->speaker_outs)
+				spk_lo_shared = !path_has_mixer(codec,
+								spec->speaker_paths[0],	ctl_type);
+			if (cfg->hp_outs)
+				hp_lo_shared = !path_has_mixer(codec, spec->hp_paths[0], ctl_type);
 			if (hp_lo_shared && spk_lo_shared)
 				return spec->vmaster_mute.hook ? "PCM" : "Master";
 			if (hp_lo_shared)
Signature · 1 line
2.30.2
author maintainer
#415 lore raw

PATCH 415/425 block: reexpand iov_iter after read/write

In reply to Greg Kroah-Hartman

From: yangerkun <[email protected]>

[ Upstream commit cf7b39a0cbf6bf57aa07a008d46cf695add05b4c ]

We get a bug:

BUG: KASAN: slab-out-of-bounds in iov_iter_revert+0x11c/0x404
lib/iov_iter.c:1139
Read of size 8 at addr ffff0000d3fb11f8 by task

CPU: 0 PID: 12582 Comm: syz-executor.2 Not tainted
5.10.0-00843-g352c8610ccd2 #2
Hardware name: linux,dummy-virt (DT)
Call trace:
 dump_backtrace+0x0/0x2d0 arch/arm64/kernel/stacktrace.c:132
 show_stack+0x28/0x34 arch/arm64/kernel/stacktrace.c:196
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x110/0x164 lib/dump_stack.c:118
 print_address_description+0x78/0x5c8 mm/kasan/report.c:385
 __kasan_report mm/kasan/report.c:545 [inline]
 kasan_report+0x148/0x1e4 mm/kasan/report.c:562
 check_memory_region_inline mm/kasan/generic.c:183 [inline]
 __asan_load8+0xb4/0xbc mm/kasan/generic.c:252
 iov_iter_revert+0x11c/0x404 lib/iov_iter.c:1139
 io_read fs/io_uring.c:3421 [inline]
 io_issue_sqe+0x2344/0x2d64 fs/io_uring.c:5943
 __io_queue_sqe+0x19c/0x520 fs/io_uring.c:6260
 io_queue_sqe+0x2a4/0x590 fs/io_uring.c:6326
 io_submit_sqe fs/io_uring.c:6395 [inline]
 io_submit_sqes+0x4c0/0xa04 fs/io_uring.c:6624
 __do_sys_io_uring_enter fs/io_uring.c:9013 [inline]
 __se_sys_io_uring_enter fs/io_uring.c:8960 [inline]
 __arm64_sys_io_uring_enter+0x190/0x708 fs/io_uring.c:8960
 __invoke_syscall arch/arm64/kernel/syscall.c:36 [inline]
 invoke_syscall arch/arm64/kernel/syscall.c:48 [inline]
 el0_svc_common arch/arm64/kernel/syscall.c:158 [inline]
 do_el0_svc+0x120/0x290 arch/arm64/kernel/syscall.c:227
 el0_svc+0x1c/0x28 arch/arm64/kernel/entry-common.c:367
 el0_sync_handler+0x98/0x170 arch/arm64/kernel/entry-common.c:383
 el0_sync+0x140/0x180 arch/arm64/kernel/entry.S:670

Allocated by task 12570:
 stack_trace_save+0x80/0xb8 kernel/stacktrace.c:121
 kasan_save_stack mm/kasan/common.c:48 [inline]
 kasan_set_track mm/kasan/common.c:56 [inline]
 __kasan_kmalloc+0xdc/0x120 mm/kasan/common.c:461
 kasan_kmalloc+0xc/0x14 mm/kasan/common.c:475
 __kmalloc+0x23c/0x334 mm/slub.c:3970
 kmalloc include/linux/slab.h:557 [inline]
 __io_alloc_async_data+0x68/0x9c fs/io_uring.c:3210
 io_setup_async_rw fs/io_uring.c:3229 [inline]
 io_read fs/io_uring.c:3436 [inline]
 io_issue_sqe+0x2954/0x2d64 fs/io_uring.c:5943
 __io_queue_sqe+0x19c/0x520 fs/io_uring.c:6260
 io_queue_sqe+0x2a4/0x590 fs/io_uring.c:6326
 io_submit_sqe fs/io_uring.c:6395 [inline]
 io_submit_sqes+0x4c0/0xa04 fs/io_uring.c:6624
 __do_sys_io_uring_enter fs/io_uring.c:9013 [inline]
 __se_sys_io_uring_enter fs/io_uring.c:8960 [inline]
 __arm64_sys_io_uring_enter+0x190/0x708 fs/io_uring.c:8960
 __invoke_syscall arch/arm64/kernel/syscall.c:36 [inline]
 invoke_syscall arch/arm64/kernel/syscall.c:48 [inline]
 el0_svc_common arch/arm64/kernel/syscall.c:158 [inline]
 do_el0_svc+0x120/0x290 arch/arm64/kernel/syscall.c:227
 el0_svc+0x1c/0x28 arch/arm64/kernel/entry-common.c:367
 el0_sync_handler+0x98/0x170 arch/arm64/kernel/entry-common.c:383
 el0_sync+0x140/0x180 arch/arm64/kernel/entry.S:670

Freed by task 12570:
 stack_trace_save+0x80/0xb8 kernel/stacktrace.c:121
 kasan_save_stack mm/kasan/common.c:48 [inline]
 kasan_set_track+0x38/0x6c mm/kasan/common.c:56
 kasan_set_free_info+0x20/0x40 mm/kasan/generic.c:355
 __kasan_slab_free+0x124/0x150 mm/kasan/common.c:422
 kasan_slab_free+0x10/0x1c mm/kasan/common.c:431
 slab_free_hook mm/slub.c:1544 [inline]
 slab_free_freelist_hook mm/slub.c:1577 [inline]
 slab_free mm/slub.c:3142 [inline]
 kfree+0x104/0x38c mm/slub.c:4124
 io_dismantle_req fs/io_uring.c:1855 [inline]
 __io_free_req+0x70/0x254 fs/io_uring.c:1867
 io_put_req_find_next fs/io_uring.c:2173 [inline]
 __io_queue_sqe+0x1fc/0x520 fs/io_uring.c:6279
 __io_req_task_submit+0x154/0x21c fs/io_uring.c:2051
 io_req_task_submit+0x2c/0x44 fs/io_uring.c:2063
 task_work_run+0xdc/0x128 kernel/task_work.c:151
 get_signal+0x6f8/0x980 kernel/signal.c:2562
 do_signal+0x108/0x3a4 arch/arm64/kernel/signal.c:658
 do_notify_resume+0xbc/0x25c arch/arm64/kernel/signal.c:722
 work_pending+0xc/0x180

blkdev_read_iter can truncate iov_iter's count since the count + pos may exceed the size of the blkdev. This will confuse io_read that we have consume the iovec. And once we do the iov_iter_revert in io_read, we will trigger the slab-out-of-bounds. Fix it by reexpand the count with size has been truncated.

blkdev_write_iter can trigger the problem too.

---
 fs/block_dev.c | 20 +++++++++++++++++---
 1 file changed, 17 insertions(+), 3 deletions(-)
fs/block_dev.c +17 -3
index 9f3faac49025..b34f76af59c4 100644
@@ -1919,6 +1919,7 @@ ssize_t blkdev_write_iter(struct kiocb *iocb, struct iov_iter *from)
 	struct inode *bd_inode = bdev_file_inode(file);
 	loff_t size = i_size_read(bd_inode);
 	struct blk_plug plug;
+	size_t shorted = 0;
 	ssize_t ret;
 
 	if (bdev_read_only(I_BDEV(bd_inode)))
@@ -1933,12 +1934,17 @@ ssize_t blkdev_write_iter(struct kiocb *iocb, struct iov_iter *from)
 	if ((iocb->ki_flags & (IOCB_NOWAIT | IOCB_DIRECT)) == IOCB_NOWAIT)
 		return -EOPNOTSUPP;
 
-	iov_iter_truncate(from, size - iocb->ki_pos);
+	size -= iocb->ki_pos;
+	if (iov_iter_count(from) > size) {
+		shorted = iov_iter_count(from) - size;
+		iov_iter_truncate(from, size);
+	}
 
 	blk_start_plug(&plug);
 	ret = __generic_file_write_iter(iocb, from);
 	if (ret > 0)
 		ret = generic_write_sync(iocb, ret);
+	iov_iter_reexpand(from, iov_iter_count(from) + shorted);
 	blk_finish_plug(&plug);
 	return ret;
 }
@@ -1950,13 +1956,21 @@ ssize_t blkdev_read_iter(struct kiocb *iocb, struct iov_iter *to)
 	struct inode *bd_inode = bdev_file_inode(file);
 	loff_t size = i_size_read(bd_inode);
 	loff_t pos = iocb->ki_pos;
+	size_t shorted = 0;
+	ssize_t ret;
 
 	if (pos >= size)
 		return 0;
 
 	size -= pos;
-	iov_iter_truncate(to, size);
-	return generic_file_read_iter(iocb, to);
+	if (iov_iter_count(to) > size) {
+		shorted = iov_iter_count(to) - size;
+		iov_iter_truncate(to, size);
+	}
+
+	ret = generic_file_read_iter(iocb, to);
+	iov_iter_reexpand(to, iov_iter_count(to) + shorted);
+	return ret;
 }
 EXPORT_SYMBOL_GPL(blkdev_read_iter);
 
Signature · 1 line
2.30.2
author maintainer
#416 lore raw

PATCH 416/425 lib: stackdepot: turn depot_lock spinlock to raw_spinlock

In reply to Greg Kroah-Hartman

From: Zqiang <[email protected]>

[ Upstream commit 78564b9434878d686c5f88c4488b20cccbcc42bc ]

In RT system, the spin_lock will be replaced by sleepable rt_mutex lock, in __call_rcu(), disable interrupts before calling kasan_record_aux_stack(), will trigger this calltrace:

  BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:951
  in_atomic(): 0, irqs_disabled(): 1, non_block: 0, pid: 19, name: pgdatinit0
  Call Trace:
    ___might_sleep.cold+0x1b2/0x1f1
    rt_spin_lock+0x3b/0xb0
    stack_depot_save+0x1b9/0x440
    kasan_save_stack+0x32/0x40
    kasan_record_aux_stack+0xa5/0xb0
    __call_rcu+0x117/0x880
    __exit_signal+0xafb/0x1180
    release_task+0x1d6/0x480
    exit_notify+0x303/0x750
    do_exit+0x678/0xcf0
    kthread+0x364/0x4f0
    ret_from_fork+0x22/0x30

Replace spinlock with raw_spinlock.

---
 lib/stackdepot.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
lib/stackdepot.c +3 -3
index 3376a3291186..d0f1b7d0ce2e 100644
@@ -78,7 +78,7 @@ static void *stack_slabs[STACK_ALLOC_MAX_SLABS];
 static int depot_index;
 static int next_slab_inited;
 static size_t depot_offset;
-static DEFINE_SPINLOCK(depot_lock);
+static DEFINE_RAW_SPINLOCK(depot_lock);
 
 static bool init_stack_slab(void **prealloc)
 {
@@ -266,7 +266,7 @@ depot_stack_handle_t depot_save_stack(struct stack_trace *trace,
 			prealloc = page_address(page);
 	}
 
-	spin_lock_irqsave(&depot_lock, flags);
+	raw_spin_lock_irqsave(&depot_lock, flags);
 
 	found = find_stack(*bucket, trace->entries, trace->nr_entries, hash);
 	if (!found) {
@@ -290,7 +290,7 @@ depot_stack_handle_t depot_save_stack(struct stack_trace *trace,
 		WARN_ON(!init_stack_slab(&prealloc));
 	}
 
-	spin_unlock_irqrestore(&depot_lock, flags);
+	raw_spin_unlock_irqrestore(&depot_lock, flags);
 exit:
 	if (prealloc) {
 		/* Nobody used this memory, ok to free it. */
Signature · 1 line
2.30.2
author maintainer
#417 lore raw

PATCH 417/425 net: stmmac: Do not enable RX FIFO overflow interrupts

In reply to Greg Kroah-Hartman

From: Yannick Vignon <[email protected]>

[ Upstream commit 8a7cb245cf28cb3e541e0d6c8624b95d079e155b ]

The RX FIFO overflows when the system is not able to process all received packets and they start accumulating (first in the DMA queue in memory, then in the FIFO). An interrupt is then raised for each overflowing packet and handled in stmmac_interrupt(). This is counter-productive, since it brings the system (or more likely, one CPU core) to its knees to process the FIFO overflow interrupts.

stmmac_interrupt() handles overflow interrupts by writing the rx tail ptr into the corresponding hardware register (according to the MAC spec, this has the effect of restarting the MAC DMA). However, without freeing any rx descriptors, the DMA stops right away, and another overflow interrupt is raised as the FIFO overflows again. Since the DMA is already restarted at the end of stmmac_rx_refill() after freeing descriptors, disabling FIFO overflow interrupts and the corresponding handling code has no side effect, and eliminates the interrupt storm when the RX FIFO overflows.

---
 drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c  |  7 +------
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 14 ++------------
 2 files changed, 3 insertions(+), 18 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c +1 -6
index 8c3780d1105f..232efe17ac2c 100644
@@ -214,7 +214,7 @@ static void dwmac4_dma_rx_chan_op_mode(void __iomem *ioaddr, int mode,
 				       u32 channel, int fifosz, u8 qmode)
 {
 	unsigned int rqs = fifosz / 256 - 1;
-	u32 mtl_rx_op, mtl_rx_int;
+	u32 mtl_rx_op;
 
 	mtl_rx_op = readl(ioaddr + MTL_CHAN_RX_OP_MODE(channel));
 
@@ -285,11 +285,6 @@ static void dwmac4_dma_rx_chan_op_mode(void __iomem *ioaddr, int mode,
 	}
 
 	writel(mtl_rx_op, ioaddr + MTL_CHAN_RX_OP_MODE(channel));
-
-	/* Enable MTL RX overflow */
-	mtl_rx_int = readl(ioaddr + MTL_CHAN_INT_CTRL(channel));
-	writel(mtl_rx_int | MTL_RX_OVERFLOW_INT_EN,
-	       ioaddr + MTL_CHAN_INT_CTRL(channel));
 }
 
 static void dwmac4_dma_tx_chan_op_mode(void __iomem *ioaddr, int mode,
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +2 -12
index a1443d7197e8..af59761ddfa0 100644
@@ -3706,7 +3706,6 @@ static irqreturn_t stmmac_interrupt(int irq, void *dev_id)
 	/* To handle GMAC own interrupts */
 	if ((priv->plat->has_gmac) || xmac) {
 		int status = stmmac_host_irq_status(priv, priv->hw, &priv->xstats);
-		int mtl_status;
 
 		if (unlikely(status)) {
 			/* For LPI we need to save the tx status */
@@ -3717,17 +3716,8 @@ static irqreturn_t stmmac_interrupt(int irq, void *dev_id)
 		}
 
 		for (queue = 0; queue < queues_count; queue++) {
-			struct stmmac_rx_queue *rx_q = &priv->rx_queue[queue];
-
-			mtl_status = stmmac_host_mtl_irq_status(priv, priv->hw,
-								queue);
-			if (mtl_status != -EINVAL)
-				status |= mtl_status;
-
-			if (status & CORE_IRQ_MTL_RX_OVERFLOW)
-				stmmac_set_rx_tail_ptr(priv, priv->ioaddr,
-						       rx_q->rx_tail_addr,
-						       queue);
+			status = stmmac_host_mtl_irq_status(priv, priv->hw,
+							    queue);
 		}
 
 		/* PCS link status */
Signature · 1 line
2.30.2
author maintainer
#418 lore raw

PATCH 418/425 ip6_gre: proper dev_{hold|put} in ndo_[un]init methods

In reply to Greg Kroah-Hartman

From: Eric Dumazet <[email protected]>

commit 7f700334be9aeb91d5d86ef9ad2d901b9b453e9b upstream.

After adopting CONFIG_PCPU_DEV_REFCNT=n option, syzbot was able to trigger a warning [1]

Issue here is that:

- all dev_put() should be paired with a corresponding dev_hold(), and vice versa.

- A driver doing a dev_put() in its ndo_uninit() MUST also do a dev_hold() in its ndo_init(), only when ndo_init() is returning 0.

Otherwise, register_netdevice() would call ndo_uninit() in its error path and release a refcount too soon.

ip6_gre for example (among others problematic drivers) has to use dev_hold() in ip6gre_tunnel_init_common() instead of from ip6gre_newlink_common(), covering both ip6gre_tunnel_init() and ip6gre_tap_init()/

Note that ip6gre_tunnel_init_common() is not called from ip6erspan_tap_init() thus we also need to add a dev_hold() there, as ip6erspan_tunnel_uninit() does call dev_put()

[1]
refcount_t: decrement hit 0; leaking memory.

WARNING: CPU: 0 PID: 8422 at lib/refcount.c:31 refcount_warn_saturate+0xbf/0x1e0 lib/refcount.c:31
Modules linked in:
CPU: 1 PID: 8422 Comm: syz-executor854 Not tainted 5.12.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:refcount_warn_saturate+0xbf/0x1e0 lib/refcount.c:31
Code: 1d 6a 5a e8 09 31 ff 89 de e8 8d 1a ab fd 84 db 75 e0 e8 d4 13 ab fd 48 c7 c7 a0 e1 c1 89 c6 05 4a 5a e8 09 01 e8 2e 36 fb 04 <0f> 0b eb c4 e8 b8 13 ab fd 0f b6 1d 39 5a e8 09 31 ff 89 de e8 58
RSP: 0018:ffffc900018befd0 EFLAGS: 00010282
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: ffff88801ef19c40 RSI: ffffffff815c51f5 RDI: fffff52000317dec
RBP: 0000000000000004 R08: 0000000000000000 R09: 0000000000000000
R10: ffffffff815bdf8e R11: 0000000000000000 R12: ffff888018cf4568
R13: ffff888018cf4c00 R14: ffff8880228f2000 R15: ffffffff8d659b80
FS:  00000000014eb300(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055d7bf2b3138 CR3: 0000000014933000 CR4: 00000000001506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 __refcount_dec include/linux/refcount.h:344 [inline]
 refcount_dec include/linux/refcount.h:359 [inline]
 dev_put include/linux/netdevice.h:4135 [inline]
 ip6gre_tunnel_uninit+0x3d7/0x440 net/ipv6/ip6_gre.c:420
 register_netdevice+0xadf/0x1500 net/core/dev.c:10308
 ip6gre_newlink_common.constprop.0+0x158/0x410 net/ipv6/ip6_gre.c:1984
 ip6gre_newlink+0x275/0x7a0 net/ipv6/ip6_gre.c:2017
 __rtnl_newlink+0x1062/0x1710 net/core/rtnetlink.c:3443
 rtnl_newlink+0x64/0xa0 net/core/rtnetlink.c:3491
 rtnetlink_rcv_msg+0x44e/0xad0 net/core/rtnetlink.c:5553
 netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2502
 netlink_unicast_kernel net/netlink/af_netlink.c:1312 [inline]
 netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1338
 netlink_sendmsg+0x856/0xd90 net/netlink/af_netlink.c:1927
 sock_sendmsg_nosec net/socket.c:654 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:674
 ____sys_sendmsg+0x6e8/0x810 net/socket.c:2350
 ___sys_sendmsg+0xf3/0x170 net/socket.c:2404
 __sys_sendmsg+0xe5/0x1b0 net/socket.c:2433
 do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
Fixes 919067cc845f ("net: add CONFIG_PCPU_DEV_REFCNT")
---
 net/ipv6/ip6_gre.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
net/ipv6/ip6_gre.c +2 -2
@@ -1503,6 +1503,7 @@ static int ip6gre_tunnel_init_common(str
 	}
 	ip6gre_tnl_init_features(dev);
 
+	dev_hold(dev);
 	return 0;
 
 cleanup_dst_cache_init:
@@ -1896,6 +1897,7 @@ static int ip6erspan_tap_init(struct net
 	dev->priv_flags |= IFF_LIVE_ADDR_CHANGE;
 	ip6erspan_tnl_link_config(tunnel, 1);
 
+	dev_hold(dev);
 	return 0;
 
 cleanup_dst_cache_init:
@@ -2001,8 +2003,6 @@ static int ip6gre_newlink_common(struct
 	if (tb[IFLA_MTU])
 		ip6_tnl_change_mtu(dev, nla_get_u32(tb[IFLA_MTU]));
 
-	dev_hold(dev);
-
 out:
 	return err;
 }
author maintainer
#419 lore raw

PATCH 419/425 sit: proper dev_{hold|put} in ndo_[un]init methods

In reply to Greg Kroah-Hartman

From: Eric Dumazet <[email protected]>

commit 6289a98f0817a4a457750d6345e754838eae9439 upstream.

After adopting CONFIG_PCPU_DEV_REFCNT=n option, syzbot was able to trigger a warning [1]

Issue here is that:

- all dev_put() should be paired with a corresponding prior dev_hold().

- A driver doing a dev_put() in its ndo_uninit() MUST also do a dev_hold() in its ndo_init(), only when ndo_init() is returning 0.

Otherwise, register_netdevice() would call ndo_uninit() in its error path and release a refcount too soon.

Fixes 919067cc845f ("net: add CONFIG_PCPU_DEV_REFCNT")
---
 net/ipv6/sit.c |    4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)
net/ipv6/sit.c +1 -3
@@ -215,8 +215,6 @@ static int ipip6_tunnel_create(struct ne
 
 	ipip6_tunnel_clone_6rd(dev, sitn);
 
-	dev_hold(dev);
-
 	ipip6_tunnel_link(sitn, t);
 	return 0;
 
@@ -1407,7 +1405,7 @@ static int ipip6_tunnel_init(struct net_
 		dev->tstats = NULL;
 		return err;
 	}
-
+	dev_hold(dev);
 	return 0;
 }
 
author maintainer
#420 lore raw

PATCH 420/425 ip6_tunnel: sit: proper dev_{hold|put} in ndo_[un]init methods

In reply to Greg Kroah-Hartman

From: Eric Dumazet <[email protected]>

commit 48bb5697269a7cbe5194dbb044dc38c517e34c58 upstream.

Same reasons than for the previous commits :
6289a98f0817 ("sit: proper dev_{hold|put} in ndo_[un]init methods") 40cb881b5aaa ("ip6_vti: proper dev_{hold|put} in ndo_[un]init methods") 7f700334be9a ("ip6_gre: proper dev_{hold|put} in ndo_[un]init methods")

After adopting CONFIG_PCPU_DEV_REFCNT=n option, syzbot was able to trigger a warning [1]

Issue here is that:

- all dev_put() should be paired with a corresponding prior dev_hold().

- A driver doing a dev_put() in its ndo_uninit() MUST also do a dev_hold() in its ndo_init(), only when ndo_init() is returning 0.

Otherwise, register_netdevice() would call ndo_uninit() in its error path and release a refcount too soon.

[1]

WARNING: CPU: 1 PID: 21059 at lib/refcount.c:31 refcount_warn_saturate+0xbf/0x1e0 lib/refcount.c:31
Modules linked in:
CPU: 1 PID: 21059 Comm: syz-executor.4 Not tainted 5.12.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:refcount_warn_saturate+0xbf/0x1e0 lib/refcount.c:31
Code: 1d 6a 5a e8 09 31 ff 89 de e8 8d 1a ab fd 84 db 75 e0 e8 d4 13 ab fd 48 c7 c7 a0 e1 c1 89 c6 05 4a 5a e8 09 01 e8 2e 36 fb 04 <0f> 0b eb c4 e8 b8 13 ab fd 0f b6 1d 39 5a e8 09 31 ff 89 de e8 58
RSP: 0018:ffffc900025aefe8 EFLAGS: 00010282
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000040000 RSI: ffffffff815c51f5 RDI: fffff520004b5def
RBP: 0000000000000004 R08: 0000000000000000 R09: 0000000000000000
R10: ffffffff815bdf8e R11: 0000000000000000 R12: ffff888023488568
R13: ffff8880254e9000 R14: 00000000dfd82cfd R15: ffff88802ee2d7c0
FS:  00007f13bc590700(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f0943e74000 CR3: 0000000025273000 CR4: 00000000001506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 __refcount_dec include/linux/refcount.h:344 [inline]
 refcount_dec include/linux/refcount.h:359 [inline]
 dev_put include/linux/netdevice.h:4135 [inline]
 ip6_tnl_dev_uninit+0x370/0x3d0 net/ipv6/ip6_tunnel.c:387
 register_netdevice+0xadf/0x1500 net/core/dev.c:10308
 ip6_tnl_create2+0x1b5/0x400 net/ipv6/ip6_tunnel.c:263
 ip6_tnl_newlink+0x312/0x580 net/ipv6/ip6_tunnel.c:2052
 __rtnl_newlink+0x1062/0x1710 net/core/rtnetlink.c:3443
 rtnl_newlink+0x64/0xa0 net/core/rtnetlink.c:3491
 rtnetlink_rcv_msg+0x44e/0xad0 net/core/rtnetlink.c:5553
 netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2502
 netlink_unicast_kernel net/netlink/af_netlink.c:1312 [inline]
 netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1338
 netlink_sendmsg+0x856/0xd90 net/netlink/af_netlink.c:1927
 sock_sendmsg_nosec net/socket.c:654 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:674
 ____sys_sendmsg+0x6e8/0x810 net/socket.c:2350
 ___sys_sendmsg+0xf3/0x170 net/socket.c:2404
 __sys_sendmsg+0xe5/0x1b0 net/socket.c:2433
 do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
 entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes 919067cc845f ("net: add CONFIG_PCPU_DEV_REFCNT")
---
 net/ipv6/ip6_tunnel.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
net/ipv6/ip6_tunnel.c +1 -1
@@ -272,7 +272,6 @@ static int ip6_tnl_create2(struct net_de
 
 	strcpy(t->parms.name, dev->name);
 
-	dev_hold(dev);
 	ip6_tnl_link(ip6n, t);
 	return 0;
 
@@ -1866,6 +1865,7 @@ ip6_tnl_dev_init_gen(struct net_device *
 	dev->min_mtu = ETH_MIN_MTU;
 	dev->max_mtu = IP6_MAX_MTU - dev->hard_header_len;
 
+	dev_hold(dev);
 	return 0;
 
 destroy_dst:
author maintainer
#421 lore raw

PATCH 421/425 ipv6: remove extra dev_hold() for fallback tunnels

In reply to Greg Kroah-Hartman

From: Eric Dumazet <[email protected]>

commit 0d7a7b2014b1a499a0fe24c9f3063d7856b5aaaf upstream.

My previous commits added a dev_hold() in tunnels ndo_init(), but forgot to remove it from special functions setting up fallback tunnels.

Fallback tunnels do call their respective ndo_init()

This leads to various reports like :

unregister_netdevice: waiting for ip6gre0 to become free. Usage count = 2

Fixes 48bb5697269a ("ip6_tunnel: sit: proper dev_{hold|put} in ndo_[un]init methods")
Fixes 6289a98f0817 ("sit: proper dev_{hold|put} in ndo_[un]init methods")
Fixes 40cb881b5aaa ("ip6_vti: proper dev_{hold|put} in ndo_[un]init methods")
Fixes 7f700334be9a ("ip6_gre: proper dev_{hold|put} in ndo_[un]init methods")
---
 net/ipv6/ip6_gre.c    |    3 ---
 net/ipv6/ip6_tunnel.c |    1 -
 net/ipv6/ip6_vti.c    |    1 -
 net/ipv6/sit.c        |    1 -
 4 files changed, 6 deletions(-)
net/ipv6/ip6_gre.c +0 -3
@@ -392,7 +392,6 @@ static struct ip6_tnl *ip6gre_tunnel_loc
 	if (!(nt->parms.o_flags & TUNNEL_SEQ))
 		dev->features |= NETIF_F_LLTX;
 
-	dev_hold(dev);
 	ip6gre_tunnel_link(ign, nt);
 	return nt;
 
@@ -1546,8 +1545,6 @@ static void ip6gre_fb_tunnel_init(struct
 	strcpy(tunnel->parms.name, dev->name);
 
 	tunnel->hlen		= sizeof(struct ipv6hdr) + 4;
-
-	dev_hold(dev);
 }
 
 static struct inet6_protocol ip6gre_protocol __read_mostly = {
net/ipv6/ip6_tunnel.c +0 -1
@@ -1909,7 +1909,6 @@ static int __net_init ip6_fb_tnl_dev_ini
 	struct ip6_tnl_net *ip6n = net_generic(net, ip6_tnl_net_id);
 
 	t->parms.proto = IPPROTO_IPV6;
-	dev_hold(dev);
 
 	rcu_assign_pointer(ip6n->tnls_wc[0], t);
 	return 0;
net/ipv6/ip6_vti.c +0 -1
@@ -956,7 +956,6 @@ static int __net_init vti6_fb_tnl_dev_in
 	struct vti6_net *ip6n = net_generic(net, vti6_net_id);
 
 	t->parms.proto = IPPROTO_IPV6;
-	dev_hold(dev);
 
 	rcu_assign_pointer(ip6n->tnls_wc[0], t);
 	return 0;
net/ipv6/sit.c +0 -1
@@ -1421,7 +1421,6 @@ static void __net_init ipip6_fb_tunnel_i
 	iph->ihl		= 5;
 	iph->ttl		= 64;
 
-	dev_hold(dev);
 	rcu_assign_pointer(sitn->tunnels_wc[0], tunnel);
 }
 
author maintainer
#422 lore raw

PATCH 422/425 iomap: fix sub-page uptodate handling

In reply to Greg Kroah-Hartman

From: Christoph Hellwig <[email protected]>

commit 1cea335d1db1ce6ab71b3d2f94a807112b738a0f upstream.

bio completions can race when a page spans more than one file system block. Add a spinlock to synchronize marking the page uptodate.

Fixes 9dc55f1389f9 ("iomap: add support for sub-pagesize buffered I/O without buffer heads")
---
 fs/iomap.c            |   34 ++++++++++++++++++++++++----------
 include/linux/iomap.h |    1 +
 2 files changed, 25 insertions(+), 10 deletions(-)
fs/iomap.c +24 -10
@@ -116,6 +116,7 @@ iomap_page_create(struct inode *inode, s
 	iop = kmalloc(sizeof(*iop), GFP_NOFS | __GFP_NOFAIL);
 	atomic_set(&iop->read_count, 0);
 	atomic_set(&iop->write_count, 0);
+	spin_lock_init(&iop->uptodate_lock);
 	bitmap_zero(iop->uptodate, PAGE_SIZE / SECTOR_SIZE);
 
 	/*
@@ -204,25 +205,38 @@ iomap_adjust_read_range(struct inode *in
 }
 
 static void
-iomap_set_range_uptodate(struct page *page, unsigned off, unsigned len)
+iomap_iop_set_range_uptodate(struct page *page, unsigned off, unsigned len)
 {
 	struct iomap_page *iop = to_iomap_page(page);
 	struct inode *inode = page->mapping->host;
 	unsigned first = off >> inode->i_blkbits;
 	unsigned last = (off + len - 1) >> inode->i_blkbits;
-	unsigned int i;
 	bool uptodate = true;
+	unsigned long flags;
+	unsigned int i;
 
-	if (iop) {
-		for (i = 0; i < PAGE_SIZE / i_blocksize(inode); i++) {
-			if (i >= first && i <= last)
-				set_bit(i, iop->uptodate);
-			else if (!test_bit(i, iop->uptodate))
-				uptodate = false;
-		}
+	spin_lock_irqsave(&iop->uptodate_lock, flags);
+	for (i = 0; i < PAGE_SIZE / i_blocksize(inode); i++) {
+		if (i >= first && i <= last)
+			set_bit(i, iop->uptodate);
+		else if (!test_bit(i, iop->uptodate))
+			uptodate = false;
 	}
 
-	if (uptodate && !PageError(page))
+	if (uptodate)
+		SetPageUptodate(page);
+	spin_unlock_irqrestore(&iop->uptodate_lock, flags);
+}
+
+static void
+iomap_set_range_uptodate(struct page *page, unsigned off, unsigned len)
+{
+	if (PageError(page))
+		return;
+
+	if (page_has_private(page))
+		iomap_iop_set_range_uptodate(page, off, len);
+	else
 		SetPageUptodate(page);
 }
 
include/linux/iomap.h +1 -0
@@ -108,6 +108,7 @@ struct iomap_ops {
 struct iomap_page {
 	atomic_t		read_count;
 	atomic_t		write_count;
+	spinlock_t		uptodate_lock;
 	DECLARE_BITMAP(uptodate, PAGE_SIZE / 512);
 };
 
author maintainer
#423 lore raw

PATCH 423/425 KVM: arm64: Initialize VCPU mdcr_el2 before loading it

In reply to Greg Kroah-Hartman

From: Alexandru Elisei <[email protected]>

commit 263d6287da1433aba11c5b4046388f2cdf49675c upstream.

When a VCPU is created, the kvm_vcpu struct is initialized to zero in kvm_vm_ioctl_create_vcpu(). On VHE systems, the first time vcpu.arch.mdcr_el2 is loaded on hardware is in vcpu_load(), before it is set to a sensible value in kvm_arm_setup_debug() later in the run loop. The result is that KVM executes for a short time with MDCR_EL2 set to zero.

This has several unintended consequences:

* Setting MDCR_EL2.HPMN to 0 is constrained unpredictable according to ARM DDI 0487G.a, page D13-3820. The behavior specified by the architecture in this case is for the PE to behave as if MDCR_EL2.HPMN is set to a value less than or equal to PMCR_EL0.N, which means that an unknown number of counters are now disabled by MDCR_EL2.HPME, which is zero.

* The host configuration for the other debug features controlled by MDCR_EL2 is temporarily lost. This has been harmless so far, as Linux doesn't use the other fields, but that might change in the future.

Let's avoid both issues by initializing the VCPU's mdcr_el2 field in kvm_vcpu_vcpu_first_run_init(), thus making sure that the MDCR_EL2 register has a consistent value after each vcpu_load().

Fixes d5a21bcc2995 ("KVM: arm64: Move common VHE/non-VHE trap config in separate functions")
---
 arch/arm/include/asm/kvm_host.h   |    1 
 arch/arm64/include/asm/kvm_host.h |    1 
 arch/arm64/kvm/debug.c            |   88 +++++++++++++++++++++++++-------------
 virt/kvm/arm/arm.c                |    2 
 4 files changed, 64 insertions(+), 28 deletions(-)
arch/arm/include/asm/kvm_host.h +1 -0
@@ -303,6 +303,7 @@ static inline void kvm_arch_sched_in(str
 static inline void kvm_arch_vcpu_block_finish(struct kvm_vcpu *vcpu) {}
 
 static inline void kvm_arm_init_debug(void) {}
+static inline void kvm_arm_vcpu_init_debug(struct kvm_vcpu *vcpu) {}
 static inline void kvm_arm_setup_debug(struct kvm_vcpu *vcpu) {}
 static inline void kvm_arm_clear_debug(struct kvm_vcpu *vcpu) {}
 static inline void kvm_arm_reset_debug_ptr(struct kvm_vcpu *vcpu) {}
arch/arm64/include/asm/kvm_host.h +1 -0
@@ -455,6 +455,7 @@ static inline void kvm_arch_sched_in(str
 static inline void kvm_arch_vcpu_block_finish(struct kvm_vcpu *vcpu) {}
 
 void kvm_arm_init_debug(void);
+void kvm_arm_vcpu_init_debug(struct kvm_vcpu *vcpu);
 void kvm_arm_setup_debug(struct kvm_vcpu *vcpu);
 void kvm_arm_clear_debug(struct kvm_vcpu *vcpu);
 void kvm_arm_reset_debug_ptr(struct kvm_vcpu *vcpu);
arch/arm64/kvm/debug.c +60 -28

131 lines not on this page · raw message

virt/kvm/arm/arm.c +2 -0
@@ -574,6 +574,8 @@ static int kvm_vcpu_first_run_init(struc
 
 	vcpu->arch.has_run_once = true;
 
+	kvm_arm_vcpu_init_debug(vcpu);
+
 	if (likely(irqchip_in_kernel(kvm))) {
 		/*
 		 * Map the VGIC hardware resources before running a vcpu the
author maintainer
#424 lore raw

PATCH 424/425 tweewide: Fix most Shebang lines

In reply to Greg Kroah-Hartman

From: Finn Behrens <[email protected]>

commit c25ce589dca10d64dde139ae093abc258a32869c upstream.

Change every shebang which does not need an argument to use /usr/bin/env. This is needed as not every distro has everything under /usr/bin, sometimes not even bash.

---
 Documentation/sphinx/parse-headers.pl                          |    2 +-
 Documentation/target/tcm_mod_builder.py                        |    2 +-
 Documentation/trace/postprocess/decode_msr.py                  |    2 +-
 Documentation/trace/postprocess/trace-pagealloc-postprocess.pl |    2 +-
 Documentation/trace/postprocess/trace-vmscan-postprocess.pl    |    2 +-
 arch/ia64/scripts/unwcheck.py                                  |    2 +-
 scripts/bloat-o-meter                                          |    2 +-
 scripts/config                                                 |    2 +-
 scripts/diffconfig                                             |    2 +-
 scripts/split-man.pl                                           |    2 +-
 tools/perf/python/tracepoint.py                                |    2 +-
 tools/testing/ktest/compare-ktest-sample.pl                    |    2 +-
 tools/testing/selftests/bpf/test_offload.py                    |    2 +-
 tools/testing/selftests/tc-testing/tdc_batch.py                |    2 +-
 14 files changed, 14 insertions(+), 14 deletions(-)
Documentation/sphinx/parse-headers.pl +1 -1
@@ -1,4 +1,4 @@
-#!/usr/bin/perl
+#!/usr/bin/env perl
 use strict;
 use Text::Tabs;
 use Getopt::Long;
Documentation/target/tcm_mod_builder.py +1 -1
@@ -1,4 +1,4 @@
-#!/usr/bin/python
+#!/usr/bin/env python
 # The TCM v4 multi-protocol fabric module generation script for drivers/target/$NEW_MOD
 #
 # Copyright (c) 2010 Rising Tide Systems
Documentation/trace/postprocess/decode_msr.py +1 -1
@@ -1,4 +1,4 @@
-#!/usr/bin/python
+#!/usr/bin/env python
 # add symbolic names to read_msr / write_msr in trace
 # decode_msr msr-index.h < trace
 import sys
Documentation/trace/postprocess/trace-pagealloc-postprocess.pl +1 -1
@@ -1,4 +1,4 @@
-#!/usr/bin/perl
+#!/usr/bin/env perl
 # This is a POC (proof of concept or piece of crap, take your pick) for reading the
 # text representation of trace output related to page allocation. It makes an attempt
 # to extract some high-level information on what is going on. The accuracy of the parser
Documentation/trace/postprocess/trace-vmscan-postprocess.pl +1 -1
@@ -1,4 +1,4 @@
-#!/usr/bin/perl
+#!/usr/bin/env perl
 # This is a POC for reading the text representation of trace output related to
 # page reclaim. It makes an attempt to extract some high-level information on
 # what is going on. The accuracy of the parser may vary
arch/ia64/scripts/unwcheck.py +1 -1
@@ -1,4 +1,4 @@
-#!/usr/bin/python
+#!/usr/bin/env python
 # SPDX-License-Identifier: GPL-2.0
 #
 # Usage: unwcheck.py FILE
scripts/bloat-o-meter +1 -1
@@ -1,4 +1,4 @@
-#!/usr/bin/python
+#!/usr/bin/env python
 #
 # Copyright 2004 Matt Mackall <[email protected]>
 #
scripts/config +1 -1
@@ -1,4 +1,4 @@
-#!/bin/bash
+#!/usr/bin/env bash
 # SPDX-License-Identifier: GPL-2.0
 # Manipulate options in a .config file from the command line
 
scripts/diffconfig +1 -1
@@ -1,4 +1,4 @@
-#!/usr/bin/python
+#!/usr/bin/env python
 # SPDX-License-Identifier: GPL-2.0
 #
 # diffconfig - a tool to compare .config files.
scripts/split-man.pl +1 -1
@@ -1,4 +1,4 @@
-#!/usr/bin/perl
+#!/usr/bin/env perl
 # SPDX-License-Identifier: GPL-2.0
 #
 # Author: Mauro Carvalho Chehab <[email protected]>
tools/perf/python/tracepoint.py +1 -1
@@ -1,4 +1,4 @@
-#! /usr/bin/python
+#! /usr/bin/env python
 # SPDX-License-Identifier: GPL-2.0
 # -*- python -*-
 # -*- coding: utf-8 -*-
tools/testing/ktest/compare-ktest-sample.pl +1 -1
@@ -1,4 +1,4 @@
-#!/usr/bin/perl
+#!/usr/bin/env perl
 # SPDX-License-Identifier: GPL-2.0
 
 open (IN,"ktest.pl");
tools/testing/selftests/bpf/test_offload.py +1 -1
@@ -1,4 +1,4 @@
-#!/usr/bin/python3
+#!/usr/bin/env python3
 
 # Copyright (C) 2017 Netronome Systems, Inc.
 #
tools/testing/selftests/tc-testing/tdc_batch.py +1 -1
@@ -1,4 +1,4 @@
-#!/usr/bin/python3
+#!/usr/bin/env python3
 
 """
 tdc_batch.py - a script to generate TC batch file
author maintainer
#425 lore raw

PATCH 425/425 scripts: switch explicitly to Python 3

In reply to Greg Kroah-Hartman

From: Andy Shevchenko <[email protected]>

commit 51839e29cb5954470ea4db7236ef8c3d77a6e0bb upstream.

Some distributions are about to switch to Python 3 support only. This means that /usr/bin/python, which is Python 2, is not available anymore. Hence, switch scripts to use Python 3 explicitly.

---
 scripts/bloat-o-meter |    2 +-
 scripts/diffconfig    |    2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)
scripts/bloat-o-meter +1 -1
@@ -1,4 +1,4 @@
-#!/usr/bin/env python
+#!/usr/bin/env python3
 #
 # Copyright 2004 Matt Mackall <[email protected]>
 #
scripts/diffconfig +1 -1
@@ -1,4 +1,4 @@
-#!/usr/bin/env python
+#!/usr/bin/env python3
 # SPDX-License-Identifier: GPL-2.0
 #
 # diffconfig - a tool to compare .config files.
#426 lore raw

Re: [PATCH 4.19 425/425] scripts: switch explicitly to Python 3

Hi!

Quoted 7 lines

From: Andy Shevchenko <[email protected]>

commit 51839e29cb5954470ea4db7236ef8c3d77a6e0bb upstream.

Some distributions are about to switch to Python 3 support only. This means that /usr/bin/python, which is Python 2, is not available anymore. Hence, switch scripts to use Python 3 explicitly.

I'd say this is unsuitable for -stable.

Old distributions may not have python3 installed, and we should not change this dependency in the middle of the series.

Python is not listed in Documentation/Changes . Perhaps it should be?

Best regards,
Pavel

Signature · 1 line
http://www.livejournal.com/~pavelmachek
author maintainer
#427 lore raw

Re: [PATCH 4.19 425/425] scripts: switch explicitly to Python 3

Quoted 6 lines · Pavel Machek

Hi!

Quoted 4 lines

From: Andy Shevchenko <[email protected]>

commit 51839e29cb5954470ea4db7236ef8c3d77a6e0bb upstream.

Quoted 8 lines
Quoted 3 lines

Some distributions are about to switch to Python 3 support only. This means that /usr/bin/python, which is Python 2, is not available anymore. Hence, switch scripts to use Python 3 explicitly.

I'd say this is unsuitable for -stable.

Old distributions may not have python3 installed, and we should not change this dependency in the middle of the series.

What distro that was released in 2017 (the year 4.14.0 was released) did not have python3 on it?

Quoted 1 line

Python is not listed in Documentation/Changes . Perhaps it should be?

It's not required to build/boot, just these helper scripts.

thanks,

greg k-h

author maintainer
#428 lore raw

Re: [PATCH 4.19 425/425] scripts: switch explicitly to Python 3

Quoted 11 lines · Greg Kroah-Hartman
Quoted 10 lines · Pavel Machek

Hi!

Quoted 7 lines

From: Andy Shevchenko <[email protected]>

commit 51839e29cb5954470ea4db7236ef8c3d77a6e0bb upstream.

Some distributions are about to switch to Python 3 support only. This means that /usr/bin/python, which is Python 2, is not available anymore. Hence, switch scripts to use Python 3 explicitly.

Quoted 7 lines
Quoted 4 lines

I'd say this is unsuitable for -stable.

Old distributions may not have python3 installed, and we should not change this dependency in the middle of the series.

What distro that was released in 2017 (the year 4.14.0 was released) did not have python3 on it?

oops, I meant 2018, when 4.19.0 was out, wrong tree...

#429 lore raw

Re: [PATCH 4.19 425/425] scripts: switch explicitly to Python 3

Quoted 14 lines · Greg Kroah-Hartman
Quoted 13 lines · Greg Kroah-Hartman
Quoted 12 lines · Pavel Machek

Hi!

Quoted 7 lines

From: Andy Shevchenko <[email protected]>

commit 51839e29cb5954470ea4db7236ef8c3d77a6e0bb upstream.

Some distributions are about to switch to Python 3 support only. This means that /usr/bin/python, which is Python 2, is not available anymore. Hence, switch scripts to use Python 3 explicitly.

I'd say this is unsuitable for -stable.

Quoted 7 lines
Quoted 5 lines
Quoted 2 lines

Old distributions may not have python3 installed, and we should not change this dependency in the middle of the series.

What distro that was released in 2017 (the year 4.14.0 was released) did not have python3 on it?

oops, I meant 2018, when 4.19.0 was out, wrong tree...

In anything yocto-based, for example, you explicitely select which packages you want. And changing dependencies in middle of stable release is surprising and against our documentation.

Best regards,
Pavel

Signature · 1 line
http://www.livejournal.com/~pavelmachek
author maintainer
#430 lore raw

Re: [PATCH 4.19 425/425] scripts: switch explicitly to Python 3

Quoted 18 lines · Pavel Machek
Quoted 17 lines · Greg Kroah-Hartman
Quoted 16 lines · Greg Kroah-Hartman
Quoted 14 lines · Pavel Machek

Hi!

Quoted 7 lines

From: Andy Shevchenko <[email protected]>

commit 51839e29cb5954470ea4db7236ef8c3d77a6e0bb upstream.

Some distributions are about to switch to Python 3 support only. This means that /usr/bin/python, which is Python 2, is not available anymore. Hence, switch scripts to use Python 3 explicitly.

I'd say this is unsuitable for -stable.

Old distributions may not have python3 installed, and we should not change this dependency in the middle of the series.

Quoted 8 lines
Quoted 4 lines
Quoted 2 lines

What distro that was released in 2017 (the year 4.14.0 was released) did not have python3 on it?

oops, I meant 2018, when 4.19.0 was out, wrong tree...

In anything yocto-based, for example, you explicitely select which packages you want. And changing dependencies in middle of stable release is surprising and against our documentation.

Yocto documentation does not dictate kernel development processes.

good luck!

greg k-h

#431 lore raw

Re: [PATCH 4.19 425/425] scripts: switch explicitly to Python 3

In reply to Pavel Machek
Quoted 3 lines · Pavel Machek
Quoted 2 lines · Greg Kroah-Hartman
Quoted 1 line · Greg Kroah-Hartman

On Thu, May 20, 2021 at 10:36:26PM +0200, Pavel Machek wrote:

...

Quoted 11 lines
Quoted 7 lines
Quoted 5 lines
Quoted 2 lines

Old distributions may not have python3 installed, and we should not change this dependency in the middle of the series.

What distro that was released in 2017 (the year 4.14.0 was released) did not have python3 on it?

oops, I meant 2018, when 4.19.0 was out, wrong tree...

In anything yocto-based, for example, you explicitely select which packages you want. And changing dependencies in middle of stable release is surprising and against our documentation.

How is this all relevant?

Scripts where the interpreter changed are not supposed to be used outside of the (kernel) development process. No user should really rely on those scripts to produce anything at any point of time or even be there.

Signature · 2 lines
With Best Regards,
Andy Shevchenko
Tested-by on the v1 series
#432 lore raw
In reply to Greg Kroah-Hartman

Hi!

Quoted 4 lines

This is the start of the stable review cycle for the 4.19.191 release. There are 425 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

CIP testing did not find any problems here:

https://gitlab.com/cip-project/cip-testing/linux-stable-rc-ci/-/tree/linux-4.19.y

Best regards,
Pavel

Signature · 2 lines
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
maintainer Tested-by on the v1 series
#433 lore raw
In reply to Greg Kroah-Hartman
Quoted 9 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.19.191 release. There are 425 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Sat, 22 May 2021 09:20:38 +0000. Anything received after that time might be too late.

The whole patch series can be found in one patch at:

Quoted 8 lines
	https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.19.191-rc1.gz

or in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.19.y
and the diffstat can be found below.

thanks,

greg k-h

All tests passing for Tegra ...

Test results for stable-v4.19:

    12 builds:	12 pass, 0 fail
    22 boots:	22 pass, 0 fail
    40 tests:	40 pass, 0 fail

Linux version: 4.19.191-rc1-g06c717b4df3a
Boards tested: tegra124-jetson-tk1, tegra186-p2771-0000,

                tegra194-p2972-0000, tegra20-ventana,
                tegra210-p2371-2180, tegra30-cardhu-a04

Jon

Tested-by on the v1 series
#434 lore raw
In reply to Greg Kroah-Hartman
Quoted 9 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.19.191 release. There are 425 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Sat, 22 May 2021 09:20:38 +0000. Anything received after that time might be too late.

The whole patch series can be found in one patch at:

Quoted 9 lines
	https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.19.191-rc1.gz

or in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.19.y
and the diffstat can be found below.

thanks,

greg k-h

Compiled and booted on my test system. No dmesg regressions.

thanks,
-- Shuah

Tested-by on the v1 series
#435 lore raw
In reply to Greg Kroah-Hartman
Quoted 8 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.19.191 release. There are 425 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Sat, 22 May 2021 09:20:38 +0000. Anything received after that time might be too late.

Build results:

	total: 155 pass: 155 fail: 0
Qemu test results:
	total: 424 pass: 424 fail: 0

Guenter

Tested-by Hulk Robot on the v1 series
#436 lore raw
In reply to Greg Kroah-Hartman
Quoted 9 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.19.191 release. There are 425 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Sat, 22 May 2021 09:20:38 +0000. Anything received after that time might be too late.

The whole patch series can be found in one patch at:

Quoted 9 lines
	https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.19.191-rc1.gz

or in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.19.y
and the diffstat can be found below.

thanks,

greg k-h

Tested on arm64 and x86 for 4.19.191-rc1,

Kernel repo:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
Branch: linux-4.19.y
Version: 4.19.191-rc1
Commit: 06c717b4df3acb666920610a100d04ebdc485e6c
Compiler: gcc version 7.3.0 (GCC)

arm64:
--------------------------------------------------------------------
Testcase Result Summary:
total: 8855
passed: 8855
failed: 0
timeout: 0
--------------------------------------------------------------------

x86:
--------------------------------------------------------------------
Testcase Result Summary:
total: 8855
passed: 8855
failed: 0
timeout: 0
--------------------------------------------------------------------

Tested-by Linux Kernel Functional Testing on the v1 series
#437 lore raw
In reply to Greg Kroah-Hartman
Quoted 10 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.19.191 release. There are 425 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Sat, 22 May 2021 09:20:38 +0000. Anything received after that time might be too late.

The whole patch series can be found in one patch at:

Quoted 8 lines
        https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.19.191-rc1.gz

or in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.19.y
and the diffstat can be found below.

thanks,

greg k-h

Results from Linaro’s test farm.
No regressions on arm64, arm, x86_64, and i386.

## Build
* kernel: 4.19.191-rc1
* git: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
* git branch: linux-4.19.y
* git commit: 06c717b4df3acb666920610a100d04ebdc485e6c
* git describe: v4.19.190-426-g06c717b4df3a
* test details:
https://qa-reports.linaro.org/lkft/linux-stable-rc-linux-4.19.y/build/v4.19.190-426-g06c717b4df3a

## No regressions (compared to v4.19.190-393-g3423fd68b29e)

## No fixes (compared to v4.19.190-393-g3423fd68b29e)

## Test result summary
total: 67254, pass: 53425, fail: 2253, skip: 10797, xfail: 779,

## Build Summary
* arm: 97 total, 97 passed, 0 failed
* arm64: 25 total, 25 passed, 0 failed
* dragonboard-410c: 1 total, 1 passed, 0 failed
* hi6220-hikey: 1 total, 1 passed, 0 failed
* i386: 14 total, 14 passed, 0 failed
* juno-r2: 1 total, 1 passed, 0 failed
* mips: 39 total, 39 passed, 0 failed
* s390: 9 total, 9 passed, 0 failed
* sparc: 9 total, 9 passed, 0 failed
* x15: 1 total, 1 passed, 0 failed
* x86: 1 total, 1 passed, 0 failed
* x86_64: 15 total, 15 passed, 0 failed

## Test suites summary
* fwts
* igt-gpu-tools
* install-android-platform-tools-r2600
* kselftest-
* kselftest-android
* kselftest-bpf
* kselftest-breakpoints
* kselftest-capabilities
* kselftest-cgroup
* kselftest-clone3
* kselftest-core
* kselftest-cpu-hotplug
* kselftest-cpufreq
* kselftest-drivers
* kselftest-efivarfs
* kselftest-filesystems
* kselftest-firmware
* kselftest-fpu
* kselftest-futex
* kselftest-gpio
* kselftest-intel_pstate
* kselftest-ipc
* kselftest-ir
* kselftest-kcmp
* kselftest-kexec
* kselftest-kvm
* kselftest-lib
* kselftest-livepatch
* kselftest-lkdtm
* kselftest-membarrier
* kselftest-memfd
* kselftest-memory-hotplug
* kselftest-mincore
* kselftest-mount
* kselftest-mqueue
* kselftest-net
* kselftest-netfilter
* kselftest-nsfs
* kselftest-openat2
* kselftest-pid_namespace
* kselftest-pidfd
* kselftest-proc
* kselftest-pstore
* kselftest-ptrace
* kselftest-rseq
* kselftest-rtc
* kselftest-seccomp
* kselftest-sigaltstack
* kselftest-size
* kselftest-splice
* kselftest-static_keys
* kselftest-sync
* kselftest-sysctl
* kselftest-tc-testing
* kselftest-timens
* kselftest-timers
* kselftest-tmpfs
* kselftest-tpm2
* kselftest-user
* kselftest-vm
* kselftest-vsyscall-mode-native-
* kselftest-vsyscall-mode-none-
* kselftest-x86
* kselftest-zram
* kvm-unit-tests
* libhugetlbfs
* linux-log-parser
* ltp-cap_bounds-tests
* ltp-commands-tests
* ltp-containers-tests
* ltp-controllers-tests
* ltp-cpuhotplug-tests
* ltp-crypto-tests
* ltp-cve-tests
* ltp-dio-tests
* ltp-fcntl-locktests-tests
* ltp-filecaps-tests
* ltp-fs-tests
* ltp-fs_bind-tests
* ltp-fs_perms_simple-tests
* ltp-fsx-tests
* ltp-hugetlb-tests
* ltp-io-tests
* ltp-ipc-tests
* ltp-math-tests
* ltp-mm-tests
* ltp-nptl-tests
* ltp-open-posix-tests
* ltp-pty-tests
* ltp-sched-tests
* ltp-securebits-tests
* ltp-syscalls-tests
* ltp-tracing-tests
* network-basic-tests
* packetdrill
* perf
* rcutorture
* ssuite
* v4l2-compliance

--
Linaro LKFT
https://lkft.linaro.org

Tested-by on the v1 series
#438 lore raw
In reply to Greg Kroah-Hartman

Hi Greg,

Quoted 7 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.19.191 release. There are 425 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Sat, 22 May 2021 09:20:38 +0000. Anything received after that time might be too late.

Build test:
mips (gcc version 11.1.1 20210430): 63 configs -> no failure arm (gcc version 11.1.1 20210430): 116 configs -> no new failure x86_64 (gcc version 10.2.1 20210110): 2 configs -> no failure

Boot test:
x86_64: Booted on my test laptop. No regression.
x86_64: Booted on qemu. No regression.

--
Regards
Sudip