dt-bindings: msm: disp: add yaml schemas for DPU bindings

Add YAML schema for the device tree bindings for DSI

Signed-off-by Krishna Manikandan <[email protected]>

Changes in v1:
- Separate dsi controller bindings to a separate patch (Stephen Boyd)
- Merge dsi-common-controller.yaml and dsi-controller-main.yaml to a single file (Stephen Boyd)
- Drop supply entries and definitions from properties (Stephen Boyd)
- Modify phy-names property for dsi controller (Stephen Boyd)
- Remove boolean from description (Stephen Boyd)
- Drop pinctrl properties as they are standard entries (Stephen Boyd)
- Modify the description for ports property and keep the reference to the generic binding where this is defined (Stephen Boyd)
- Add description to clock names (Stephen Boyd)
- Correct the indendation (Stephen Boyd)
- Drop the label for display dt nodes and correct the node name (Stephen Boyd)

Changes in v2:
- Drop maxItems for clock (Stephen Boyd)
- Drop qcom,mdss-mdp-transfer-time-us as it is not used in upstream dt file (Stephen Boyd)
- Keep child node directly under soc node (Stephen Boyd)
- Drop qcom,sync-dual-dsi as it is not used in upstream dt

Changes in v3:
- Add description for register property (Stephen Boyd)

Changes in v4:
- Add maxItems for phys property (Stephen Boyd)
- Add maxItems for reg property (Stephen Boyd)
- Add reference for data-lanes property (Stephen Boyd)
- Remove soc from example (Stephen Boyd)

Changes in v5:
- Modify title and description (Stephen Boyd)
- Add required properties for ports node (Stephen Boyd)
- Add data-lanes in the example (Stephen Boyd)
- Drop qcom,master-dsi property (Stephen Boyd)

Changes in v6:
- Add required properties for port@0, port@1 and corresponding endpoints (Stephen Boyd)
- Add address-cells and size-cells for ports (Stephen Boyd)
- Use additionalProperties instead of unevaluatedProperties (Stephen Boyd)

Changes in v7:
- Add reference for ports and data-lanes (Rob Herring)
- Add maxItems and minItems for data-lanes (Rob Herring)

Changes in v8:
- Drop common properties and description from ports (Rob Herring)
- Add reference for endpoint (Rob Herring)
- Add correct reference for data-lanes (Rob Herring)
- Drop common properties from required list for ports (Rob Herring)

---
 .../bindings/display/msm/dsi-controller-main.yaml  | 185 +++++++++++++++
 .../devicetree/bindings/display/msm/dsi.txt        | 249 ---------------------
 2 files changed, 185 insertions(+), 249 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml
 delete mode 100644 Documentation/devicetree/bindings/display/msm/dsi.txt

Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml new file +185 -0

new file mode 100644
index 0000000..df6a750
@@ -0,0 +1,185 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dsi-controller-main.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Display DSI controller
+
+maintainers:
+  - Krishna Manikandan <[email protected]>
+
+allOf:
+  - $ref: "../dsi-controller.yaml#"
+
+properties:
+  compatible:
+    items:
+      - const: qcom,mdss-dsi-ctrl
+
+  reg:
+    maxItems: 1
+
+  reg-names:
+    const: dsi_ctrl
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Display byte clock
+      - description: Display byte interface clock
+      - description: Display pixel clock
+      - description: Display escape clock
+      - description: Display AHB clock
+      - description: Display AXI clock
+
+  clock-names:
+    items:
+      - const: byte
+      - const: byte_intf
+      - const: pixel
+      - const: core
+      - const: iface
+      - const: bus
+
+  phys:
+    maxItems: 1
+
+  phy-names:
+    const: dsi
+
+  "#address-cells": true
+
+  "#size-cells": true
+
+  syscon-sfpb:
+    description: A phandle to mmss_sfpb syscon node (only for DSIv2).
+    $ref: "/schemas/types.yaml#/definitions/phandle"
+
+  qcom,dual-dsi-mode:
+    type: boolean
+    description: |
+      Indicates if the DSI controller is driving a panel which needs
+      2 DSI links.
+
+  power-domains:
+    maxItems: 1
+
+  operating-points-v2: true
+
+  ports:
+    $ref: "/schemas/graph.yaml#/properties/ports"
+    description: |
+      Contains DSI controller input and output ports as children, each
+      containing one endpoint subnode.
+
+    properties:
+      port@0:
+        $ref: "/schemas/graph.yaml#/properties/port"
+        description: |
+          Input endpoints of the controller.
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            properties:
+              data-lanes:
+                $ref: /schemas/types.yaml#/definitions/uint32-array
+                maxItems: 4
+                minItems: 4
+                items:
+                  enum: [ 0, 1, 2, 3 ]
+
+      port@1:
+        $ref: "/schemas/graph.yaml#/properties/port"
+        description: |
+          Output endpoints of the controller.
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            properties:
+              data-lanes:
+                $ref: /schemas/types.yaml#/definitions/uint32-array
+                maxItems: 4
+                minItems: 4
+                items:
+                  enum: [ 0, 1, 2, 3 ]
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - interrupts
+  - clocks
+  - clock-names
+  - phys
+  - phy-names
+  - power-domains
+  - operating-points-v2
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+     #include <dt-bindings/interrupt-controller/arm-gic.h>
+     #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
+     #include <dt-bindings/clock/qcom,gcc-sdm845.h>
+     #include <dt-bindings/power/qcom-rpmpd.h>
+
+     dsi@ae94000 {
+           compatible = "qcom,mdss-dsi-ctrl";
+           reg = <0x0ae94000 0x400>;
+           reg-names = "dsi_ctrl";
+
+           #address-cells = <1>;
+           #size-cells = <0>;
+
+           interrupt-parent = <&mdss>;
+           interrupts = <4>;
+
+           clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+                    <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+                    <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+                    <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+                    <&dispcc DISP_CC_MDSS_AHB_CLK>,
+                    <&dispcc DISP_CC_MDSS_AXI_CLK>;
+           clock-names = "byte",
+                         "byte_intf",
+                         "pixel",
+                         "core",
+                         "iface",
+                         "bus";
+
+           phys = <&dsi0_phy>;
+           phy-names = "dsi";
+
+           power-domains = <&rpmhpd SC7180_CX>;
+           operating-points-v2 = <&dsi_opp_table>;
+
+           ports {
+                  #address-cells = <1>;
+                  #size-cells = <0>;
+
+                  port@0 {
+                          reg = <0>;
+                          dsi0_in: endpoint {
+                                   remote-endpoint = <&dpu_intf1_out>;
+                          };
+                  };
+
+                  port@1 {
+                          reg = <1>;
+                          dsi0_out: endpoint {
+                                   remote-endpoint = <&sn65dsi86_in>;
+                                   data-lanes = <0 1 2 3>;
+                          };
+                  };
+           };
+     };
+...

Documentation/devicetree/bindings/display/msm/dsi.txt deleted +0 -249

deleted file mode 100644
index b9a64d3..0000000
@@ -1,249 +0,0 @@
-Qualcomm Technologies Inc. adreno/snapdragon DSI output
-
-DSI Controller:
-Required properties:
-- compatible:
-  * "qcom,mdss-dsi-ctrl"
-- reg: Physical base address and length of the registers of controller
-- reg-names: The names of register regions. The following regions are required:
-  * "dsi_ctrl"
-- interrupts: The interrupt signal from the DSI block.
-- power-domains: Should be <&mmcc MDSS_GDSC>.
-- clocks: Phandles to device clocks.
-- clock-names: the following clocks are required:
-  * "mdp_core"
-  * "iface"
-  * "bus"
-  * "core_mmss"
-  * "byte"
-  * "pixel"
-  * "core"
-  For DSIv2, we need an additional clock:
-   * "src"
-  For DSI6G v2.0 onwards, we need also need the clock:
-   * "byte_intf"
-- assigned-clocks: Parents of "byte" and "pixel" for the given platform.
-- assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided
-  by a DSI PHY block. See [1] for details on clock bindings.
-- vdd-supply: phandle to vdd regulator device node
-- vddio-supply: phandle to vdd-io regulator device node
-- vdda-supply: phandle to vdda regulator device node
-- phys: phandle to DSI PHY device node
-- phy-names: the name of the corresponding PHY device
-- syscon-sfpb: A phandle to mmss_sfpb syscon node (only for DSIv2)
-- ports: Contains 2 DSI controller ports as child nodes. Each port contains
-  an endpoint subnode as defined in [2] and [3].
-
-Optional properties:
-- panel@0: Node of panel connected to this DSI controller.
-  See files in [4] for each supported panel.
-- qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is
-  driving a panel which needs 2 DSI links.
-- qcom,master-dsi: Boolean value indicating if the DSI controller is driving
-  the master link of the 2-DSI panel.
-- qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is
-  driving a 2-DSI panel whose 2 links need receive command simultaneously.
-- pinctrl-names: the pin control state names; should contain "default"
-- pinctrl-0: the default pinctrl state (active)
-- pinctrl-n: the "sleep" pinctrl state
-- ports: contains DSI controller input and output ports as children, each
-  containing one endpoint subnode.
-
-  DSI Endpoint properties:
-  - remote-endpoint: For port@0, set to phandle of the connected panel/bridge's
-    input endpoint. For port@1, set to the MDP interface output. See [2] for
-    device graph info.
-
-  - data-lanes: this describes how the physical DSI data lanes are mapped
-    to the logical lanes on the given platform. The value contained in
-    index n describes what physical lane is mapped to the logical lane n
-    (DATAn, where n lies between 0 and 3). The clock lane position is fixed
-    and can't be changed. Hence, they aren't a part of the DT bindings. See
-    [3] for more info on the data-lanes property.
-
-    For example:
-
-    data-lanes = <3 0 1 2>;
-
-    The above mapping describes that the logical data lane DATA0 is mapped to
-    the physical data lane DATA3, logical DATA1 to physical DATA0, logic DATA2
-    to phys DATA1 and logic DATA3 to phys DATA2.
-
-    There are only a limited number of physical to logical mappings possible:
-    <0 1 2 3>
-    <1 2 3 0>
-    <2 3 0 1>
-    <3 0 1 2>
-    <0 3 2 1>
-    <1 0 3 2>
-    <2 1 0 3>
-    <3 2 1 0>
-
-DSI PHY:
-Required properties:
-- compatible: Could be the following
-  * "qcom,dsi-phy-28nm-hpm"
-  * "qcom,dsi-phy-28nm-lp"
-  * "qcom,dsi-phy-20nm"
-  * "qcom,dsi-phy-28nm-8960"
-  * "qcom,dsi-phy-14nm"
-  * "qcom,dsi-phy-14nm-660"
-  * "qcom,dsi-phy-10nm"
-  * "qcom,dsi-phy-10nm-8998"
-  * "qcom,dsi-phy-7nm"
-  * "qcom,dsi-phy-7nm-8150"
-- reg: Physical base address and length of the registers of PLL, PHY. Some
-  revisions require the PHY regulator base address, whereas others require the
-  PHY lane base address. See below for each PHY revision.
-- reg-names: The names of register regions. The following regions are required:
-  For DSI 28nm HPM/LP/8960 PHYs and 20nm PHY:
-  * "dsi_pll"
-  * "dsi_phy"
-  * "dsi_phy_regulator"
-  For DSI 14nm, 10nm and 7nm PHYs:
-  * "dsi_pll"
-  * "dsi_phy"
-  * "dsi_phy_lane"
-- clock-cells: Must be 1. The DSI PHY block acts as a clock provider, creating
-  2 clocks: A byte clock (index 0), and a pixel clock (index 1).
-- power-domains: Should be <&mmcc MDSS_GDSC>.
-- clocks: Phandles to device clocks. See [1] for details on clock bindings.
-- clock-names: the following clocks are required:
-  * "iface"
-  * "ref" (only required for new DTS files/entries)
-  For 28nm HPM/LP, 28nm 8960 PHYs:
-- vddio-supply: phandle to vdd-io regulator device node
-  For 20nm PHY:
-- vddio-supply: phandle to vdd-io regulator device node
-- vcca-supply: phandle to vcca regulator device node
-  For 14nm PHY:
-- vcca-supply: phandle to vcca regulator device node
-  For 10nm and 7nm PHY:
-- vdds-supply: phandle to vdds regulator device node
-
-Optional properties:
-- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY
-  regulator is wanted.
-- qcom,mdss-mdp-transfer-time-us:	Specifies the dsi transfer time for command mode
-					panels in microseconds. Driver uses this number to adjust
-					the clock rate according to the expected transfer time.
-					Increasing this value would slow down the mdp processing
-					and can result in slower performance.
-					Decreasing this value can speed up the mdp processing,
-					but this can also impact power consumption.
-					As a rule this time should not be higher than the time
-					that would be expected with the processing at the
-					dsi link rate since anyways this would be the maximum
-					transfer time that could be achieved.
-					If ping pong split is enabled, this time should not be higher
-					than two times the dsi link rate time.
-					If the property is not specified, then the default value is 14000 us.
-
-[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
-[2] Documentation/devicetree/bindings/graph.txt
-[3] Documentation/devicetree/bindings/media/video-interfaces.txt
-[4] Documentation/devicetree/bindings/display/panel/
-
-Example:
-	dsi0: dsi@fd922800 {
-		compatible = "qcom,mdss-dsi-ctrl";
-		qcom,dsi-host-index = <0>;
-		interrupt-parent = <&mdp>;
-		interrupts = <4 0>;
-		reg-names = "dsi_ctrl";
-		reg = <0xfd922800 0x200>;
-		power-domains = <&mmcc MDSS_GDSC>;
-		clock-names =
-			"bus",
-			"byte",
-			"core",
-			"core_mmss",
-			"iface",
-			"mdp_core",
-			"pixel";
-		clocks =
-			<&mmcc MDSS_AXI_CLK>,
-			<&mmcc MDSS_BYTE0_CLK>,
-			<&mmcc MDSS_ESC0_CLK>,
-			<&mmcc MMSS_MISC_AHB_CLK>,
-			<&mmcc MDSS_AHB_CLK>,
-			<&mmcc MDSS_MDP_CLK>,
-			<&mmcc MDSS_PCLK0_CLK>;
-
-		assigned-clocks =
-				 <&mmcc BYTE0_CLK_SRC>,
-				 <&mmcc PCLK0_CLK_SRC>;
-		assigned-clock-parents =
-				 <&dsi_phy0 0>,
-				 <&dsi_phy0 1>;
-
-		vdda-supply = <&pma8084_l2>;
-		vdd-supply = <&pma8084_l22>;
-		vddio-supply = <&pma8084_l12>;
-
-		phys = <&dsi_phy0>;
-		phy-names ="dsi-phy";
-
-		qcom,dual-dsi-mode;
-		qcom,master-dsi;
-		qcom,sync-dual-dsi;
-
-		qcom,mdss-mdp-transfer-time-us = <12000>;
-
-		pinctrl-names = "default", "sleep";
-		pinctrl-0 = <&dsi_active>;
-		pinctrl-1 = <&dsi_suspend>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				dsi0_in: endpoint {
-					remote-endpoint = <&mdp_intf1_out>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-				dsi0_out: endpoint {
-					remote-endpoint = <&panel_in>;
-					data-lanes = <0 1 2 3>;
-				};
-			};
-		};
-
-		panel: panel@0 {
-			compatible = "sharp,lq101r1sx01";
-			reg = <0>;
-			link2 = <&secondary>;
-
-			power-supply = <...>;
-			backlight = <...>;
-
-			port {
-				panel_in: endpoint {
-					remote-endpoint = <&dsi0_out>;
-				};
-			};
-		};
-	};
-
-	dsi_phy0: dsi-phy@fd922a00 {
-		compatible = "qcom,dsi-phy-28nm-hpm";
-		qcom,dsi-phy-index = <0>;
-		reg-names =
-			"dsi_pll",
-			"dsi_phy",
-			"dsi_phy_regulator";
-		reg =   <0xfd922a00 0xd4>,
-			<0xfd922b00 0x2b0>,
-			<0xfd922d80 0x7b>;
-		clock-names = "iface";
-		clocks = <&mmcc MDSS_AHB_CLK>;
-		#clock-cells = <1>;
-		vddio-supply = <&pma8084_l12>;
-
-		qcom,dsi-phy-regulator-ldo-mode;
-	};

Signature · 1 line

2.7.4

Add YAML schema for the device tree bindings for DSI

Signed-off-by Krishna Manikandan <[email protected]>

Changes in v1:
- Separate dsi controller bindings to a separate patch (Stephen Boyd)
- Merge dsi-common-controller.yaml and dsi-controller-main.yaml to a single file (Stephen Boyd)
- Drop supply entries and definitions from properties (Stephen Boyd)
- Modify phy-names property for dsi controller (Stephen Boyd)
- Remove boolean from description (Stephen Boyd)
- Drop pinctrl properties as they are standard entries (Stephen Boyd)
- Modify the description for ports property and keep the reference to the generic binding where this is defined (Stephen Boyd)
- Add description to clock names (Stephen Boyd)
- Correct the indendation (Stephen Boyd)
- Drop the label for display dt nodes and correct the node name (Stephen Boyd)

Changes in v2:
- Drop maxItems for clock (Stephen Boyd)
- Drop qcom,mdss-mdp-transfer-time-us as it is not used in upstream dt file (Stephen Boyd)
- Keep child node directly under soc node (Stephen Boyd)
- Drop qcom,sync-dual-dsi as it is not used in upstream dt

Changes in v3:
- Add description for register property (Stephen Boyd)

Changes in v4:
- Add maxItems for phys property (Stephen Boyd)
- Add maxItems for reg property (Stephen Boyd)
- Add reference for data-lanes property (Stephen Boyd)
- Remove soc from example (Stephen Boyd)

Changes in v5:
- Modify title and description (Stephen Boyd)
- Add required properties for ports node (Stephen Boyd)
- Add data-lanes in the example (Stephen Boyd)
- Drop qcom,master-dsi property (Stephen Boyd)

Changes in v6:
- Add required properties for port@0, port@1 and corresponding endpoints (Stephen Boyd)
- Add address-cells and size-cells for ports (Stephen Boyd)
- Use additionalProperties instead of unevaluatedProperties (Stephen Boyd)

Changes in v7:
- Add reference for ports and data-lanes (Rob Herring)
- Add maxItems and minItems for data-lanes (Rob Herring)

Changes in v8:
- Drop common properties and description from ports (Rob Herring)
- Add reference for endpoint (Rob Herring)
- Add correct reference for data-lanes (Rob Herring)
- Drop common properties from required list for ports (Rob Herring)

---
 .../bindings/display/msm/dsi-controller-main.yaml  | 185 +++++++++++++++
 .../devicetree/bindings/display/msm/dsi.txt        | 249 ---------------------
 2 files changed, 185 insertions(+), 249 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml
 delete mode 100644 Documentation/devicetree/bindings/display/msm/dsi.txt

Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml new file +75 -0

new file mode 100644
index 0000000..df6a750
@@ -0,0 +1,185 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dsi-controller-main.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Display DSI controller
+
+maintainers:
+  - Krishna Manikandan <[email protected]>
+
+allOf:
+  - $ref: "../dsi-controller.yaml#"
+
+properties:
+  compatible:
+    items:
+      - const: qcom,mdss-dsi-ctrl
+
+  reg:
+    maxItems: 1
+
+  reg-names:
+    const: dsi_ctrl
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Display byte clock
+      - description: Display byte interface clock
+      - description: Display pixel clock
+      - description: Display escape clock
+      - description: Display AHB clock
+      - description: Display AXI clock
+
+  clock-names:
+    items:
+      - const: byte
+      - const: byte_intf
+      - const: pixel
+      - const: core
+      - const: iface
+      - const: bus
+
+  phys:
+    maxItems: 1
+
+  phy-names:
+    const: dsi
+
+  "#address-cells": true
+
+  "#size-cells": true
+
+  syscon-sfpb:
+    description: A phandle to mmss_sfpb syscon node (only for DSIv2).
+    $ref: "/schemas/types.yaml#/definitions/phandle"
+
+  qcom,dual-dsi-mode:
+    type: boolean
+    description: |
+      Indicates if the DSI controller is driving a panel which needs
+      2 DSI links.
+
+  power-domains:
+    maxItems: 1
+
+  operating-points-v2: true
+
+  ports:
+    $ref: "/schemas/graph.yaml#/properties/ports"
+    description: |
+      Contains DSI controller input and output ports as children, each

Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml new file +82 -0

+                maxItems: 4
+                minItems: 4
+                items:
+                  enum: [ 0, 1, 2, 3 ]
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - interrupts
+  - clocks
+  - clock-names
+  - phys
+  - phy-names
+  - power-domains
+  - operating-points-v2
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+     #include <dt-bindings/interrupt-controller/arm-gic.h>
+     #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
+     #include <dt-bindings/clock/qcom,gcc-sdm845.h>
+     #include <dt-bindings/power/qcom-rpmpd.h>
+
+     dsi@ae94000 {
+           compatible = "qcom,mdss-dsi-ctrl";
+           reg = <0x0ae94000 0x400>;
+           reg-names = "dsi_ctrl";
+
+           #address-cells = <1>;
+           #size-cells = <0>;
+
+           interrupt-parent = <&mdss>;
+           interrupts = <4>;
+
+           clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+                    <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+                    <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+                    <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+                    <&dispcc DISP_CC_MDSS_AHB_CLK>,
+                    <&dispcc DISP_CC_MDSS_AXI_CLK>;
+           clock-names = "byte",
+                         "byte_intf",
+                         "pixel",
+                         "core",
+                         "iface",
+                         "bus";
+
+           phys = <&dsi0_phy>;
+           phy-names = "dsi";
+
+           power-domains = <&rpmhpd SC7180_CX>;
+           operating-points-v2 = <&dsi_opp_table>;
+
+           ports {
+                  #address-cells = <1>;
+                  #size-cells = <0>;
+
+                  port@0 {
+                          reg = <0>;
+                          dsi0_in: endpoint {
+                                   remote-endpoint = <&dpu_intf1_out>;
+                          };
+                  };
+
+                  port@1 {
+                          reg = <1>;
+                          dsi0_out: endpoint {
+                                   remote-endpoint = <&sn65dsi86_in>;
+                                   data-lanes = <0 1 2 3>;
+                          };
+                  };
+           };
+     };
+...

Documentation/devicetree/bindings/display/msm/dsi.txt deleted +0 -249

deleted file mode 100644
index b9a64d3..0000000
@@ -1,249 +0,0 @@
-Qualcomm Technologies Inc. adreno/snapdragon DSI output
-
-DSI Controller:
-Required properties:
-- compatible:
-  * "qcom,mdss-dsi-ctrl"
-- reg: Physical base address and length of the registers of controller
-- reg-names: The names of register regions. The following regions are required:
-  * "dsi_ctrl"
-- interrupts: The interrupt signal from the DSI block.
-- power-domains: Should be <&mmcc MDSS_GDSC>.
-- clocks: Phandles to device clocks.
-- clock-names: the following clocks are required:
-  * "mdp_core"
-  * "iface"
-  * "bus"
-  * "core_mmss"
-  * "byte"
-  * "pixel"
-  * "core"
-  For DSIv2, we need an additional clock:
-   * "src"
-  For DSI6G v2.0 onwards, we need also need the clock:
-   * "byte_intf"
-- assigned-clocks: Parents of "byte" and "pixel" for the given platform.
-- assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided
-  by a DSI PHY block. See [1] for details on clock bindings.
-- vdd-supply: phandle to vdd regulator device node
-- vddio-supply: phandle to vdd-io regulator device node
-- vdda-supply: phandle to vdda regulator device node
-- phys: phandle to DSI PHY device node
-- phy-names: the name of the corresponding PHY device
-- syscon-sfpb: A phandle to mmss_sfpb syscon node (only for DSIv2)
-- ports: Contains 2 DSI controller ports as child nodes. Each port contains
-  an endpoint subnode as defined in [2] and [3].
-
-Optional properties:
-- panel@0: Node of panel connected to this DSI controller.
-  See files in [4] for each supported panel.
-- qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is
-  driving a panel which needs 2 DSI links.
-- qcom,master-dsi: Boolean value indicating if the DSI controller is driving
-  the master link of the 2-DSI panel.
-- qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is
-  driving a 2-DSI panel whose 2 links need receive command simultaneously.
-- pinctrl-names: the pin control state names; should contain "default"
-- pinctrl-0: the default pinctrl state (active)
-- pinctrl-n: the "sleep" pinctrl state
-- ports: contains DSI controller input and output ports as children, each
-  containing one endpoint subnode.
-
-  DSI Endpoint properties:
-  - remote-endpoint: For port@0, set to phandle of the connected panel/bridge's
-    input endpoint. For port@1, set to the MDP interface output. See [2] for
-    device graph info.
-
-  - data-lanes: this describes how the physical DSI data lanes are mapped
-    to the logical lanes on the given platform. The value contained in
-    index n describes what physical lane is mapped to the logical lane n
-    (DATAn, where n lies between 0 and 3). The clock lane position is fixed
-    and can't be changed. Hence, they aren't a part of the DT bindings. See
-    [3] for more info on the data-lanes property.
-
-    For example:
-
-    data-lanes = <3 0 1 2>;
-
-    The above mapping describes that the logical data lane DATA0 is mapped to
-    the physical data lane DATA3, logical DATA1 to physical DATA0, logic DATA2
-    to phys DATA1 and logic DATA3 to phys DATA2.
-
-    There are only a limited number of physical to logical mappings possible:
-    <0 1 2 3>
-    <1 2 3 0>
-    <2 3 0 1>
-    <3 0 1 2>
-    <0 3 2 1>
-    <1 0 3 2>
-    <2 1 0 3>
-    <3 2 1 0>
-
-DSI PHY:
-Required properties:
-- compatible: Could be the following
-  * "qcom,dsi-phy-28nm-hpm"
-  * "qcom,dsi-phy-28nm-lp"
-  * "qcom,dsi-phy-20nm"
-  * "qcom,dsi-phy-28nm-8960"
-  * "qcom,dsi-phy-14nm"
-  * "qcom,dsi-phy-14nm-660"
-  * "qcom,dsi-phy-10nm"
-  * "qcom,dsi-phy-10nm-8998"
-  * "qcom,dsi-phy-7nm"
-  * "qcom,dsi-phy-7nm-8150"
-- reg: Physical base address and length of the registers of PLL, PHY. Some
-  revisions require the PHY regulator base address, whereas others require the
-  PHY lane base address. See below for each PHY revision.
-- reg-names: The names of register regions. The following regions are required:
-  For DSI 28nm HPM/LP/8960 PHYs and 20nm PHY:
-  * "dsi_pll"
-  * "dsi_phy"
-  * "dsi_phy_regulator"
-  For DSI 14nm, 10nm and 7nm PHYs:
-  * "dsi_pll"
-  * "dsi_phy"
-  * "dsi_phy_lane"
-- clock-cells: Must be 1. The DSI PHY block acts as a clock provider, creating
-  2 clocks: A byte clock (index 0), and a pixel clock (index 1).
-- power-domains: Should be <&mmcc MDSS_GDSC>.
-- clocks: Phandles to device clocks. See [1] for details on clock bindings.
-- clock-names: the following clocks are required:
-  * "iface"
-  * "ref" (only required for new DTS files/entries)
-  For 28nm HPM/LP, 28nm 8960 PHYs:
-- vddio-supply: phandle to vdd-io regulator device node
-  For 20nm PHY:
-- vddio-supply: phandle to vdd-io regulator device node
-- vcca-supply: phandle to vcca regulator device node
-  For 14nm PHY:
-- vcca-supply: phandle to vcca regulator device node
-  For 10nm and 7nm PHY:
-- vdds-supply: phandle to vdds regulator device node
-
-Optional properties:
-- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY
-  regulator is wanted.
-- qcom,mdss-mdp-transfer-time-us:	Specifies the dsi transfer time for command mode
-					panels in microseconds. Driver uses this number to adjust
-					the clock rate according to the expected transfer time.
-					Increasing this value would slow down the mdp processing
-					and can result in slower performance.
-					Decreasing this value can speed up the mdp processing,
-					but this can also impact power consumption.
-					As a rule this time should not be higher than the time
-					that would be expected with the processing at the
-					dsi link rate since anyways this would be the maximum
-					transfer time that could be achieved.
-					If ping pong split is enabled, this time should not be higher
-					than two times the dsi link rate time.
-					If the property is not specified, then the default value is 14000 us.
-
-[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
-[2] Documentation/devicetree/bindings/graph.txt
-[3] Documentation/devicetree/bindings/media/video-interfaces.txt
-[4] Documentation/devicetree/bindings/display/panel/
-
-Example:
-	dsi0: dsi@fd922800 {
-		compatible = "qcom,mdss-dsi-ctrl";
-		qcom,dsi-host-index = <0>;
-		interrupt-parent = <&mdp>;
-		interrupts = <4 0>;
-		reg-names = "dsi_ctrl";
-		reg = <0xfd922800 0x200>;
-		power-domains = <&mmcc MDSS_GDSC>;
-		clock-names =
-			"bus",
-			"byte",
-			"core",
-			"core_mmss",
-			"iface",
-			"mdp_core",
-			"pixel";
-		clocks =
-			<&mmcc MDSS_AXI_CLK>,
-			<&mmcc MDSS_BYTE0_CLK>,
-			<&mmcc MDSS_ESC0_CLK>,
-			<&mmcc MMSS_MISC_AHB_CLK>,
-			<&mmcc MDSS_AHB_CLK>,
-			<&mmcc MDSS_MDP_CLK>,
-			<&mmcc MDSS_PCLK0_CLK>;
-
-		assigned-clocks =
-				 <&mmcc BYTE0_CLK_SRC>,
-				 <&mmcc PCLK0_CLK_SRC>;
-		assigned-clock-parents =
-				 <&dsi_phy0 0>,
-				 <&dsi_phy0 1>;
-
-		vdda-supply = <&pma8084_l2>;
-		vdd-supply = <&pma8084_l22>;
-		vddio-supply = <&pma8084_l12>;
-
-		phys = <&dsi_phy0>;
-		phy-names ="dsi-phy";
-
-		qcom,dual-dsi-mode;
-		qcom,master-dsi;
-		qcom,sync-dual-dsi;
-
-		qcom,mdss-mdp-transfer-time-us = <12000>;
-
-		pinctrl-names = "default", "sleep";
-		pinctrl-0 = <&dsi_active>;
-		pinctrl-1 = <&dsi_suspend>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				dsi0_in: endpoint {
-					remote-endpoint = <&mdp_intf1_out>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-				dsi0_out: endpoint {
-					remote-endpoint = <&panel_in>;
-					data-lanes = <0 1 2 3>;
-				};
-			};
-		};
-
-		panel: panel@0 {
-			compatible = "sharp,lq101r1sx01";
-			reg = <0>;
-			link2 = <&secondary>;
-
-			power-supply = <...>;
-			backlight = <...>;
-
-			port {
-				panel_in: endpoint {
-					remote-endpoint = <&dsi0_out>;
-				};
-			};
-		};
-	};
-
-	dsi_phy0: dsi-phy@fd922a00 {
-		compatible = "qcom,dsi-phy-28nm-hpm";
-		qcom,dsi-phy-index = <0>;
-		reg-names =
-			"dsi_pll",
-			"dsi_phy",
-			"dsi_phy_regulator";
-		reg =   <0xfd922a00 0xd4>,
-			<0xfd922b00 0x2b0>,
-			<0xfd922d80 0x7b>;
-		clock-names = "iface";
-		clocks = <&mmcc MDSS_AHB_CLK>;
-		#clock-cells = <1>;
-		vddio-supply = <&pma8084_l12>;
-
-		qcom,dsi-phy-regulator-ldo-mode;
-	};

Signature · 1 line

2.7.4

Add YAML schema for the device tree bindings for DSI

Signed-off-by Krishna Manikandan <[email protected]>

Changes in v1:
- Separate dsi controller bindings to a separate patch (Stephen Boyd)
- Merge dsi-common-controller.yaml and dsi-controller-main.yaml to a single file (Stephen Boyd)
- Drop supply entries and definitions from properties (Stephen Boyd)
- Modify phy-names property for dsi controller (Stephen Boyd)
- Remove boolean from description (Stephen Boyd)
- Drop pinctrl properties as they are standard entries (Stephen Boyd)
- Modify the description for ports property and keep the reference to the generic binding where this is defined (Stephen Boyd)
- Add description to clock names (Stephen Boyd)
- Correct the indendation (Stephen Boyd)
- Drop the label for display dt nodes and correct the node name (Stephen Boyd)

Changes in v2:
- Drop maxItems for clock (Stephen Boyd)
- Drop qcom,mdss-mdp-transfer-time-us as it is not used in upstream dt file (Stephen Boyd)
- Keep child node directly under soc node (Stephen Boyd)
- Drop qcom,sync-dual-dsi as it is not used in upstream dt

Changes in v3:
- Add description for register property (Stephen Boyd)

Changes in v4:
- Add maxItems for phys property (Stephen Boyd)
- Add maxItems for reg property (Stephen Boyd)
- Add reference for data-lanes property (Stephen Boyd)
- Remove soc from example (Stephen Boyd)

Changes in v5:
- Modify title and description (Stephen Boyd)
- Add required properties for ports node (Stephen Boyd)
- Add data-lanes in the example (Stephen Boyd)
- Drop qcom,master-dsi property (Stephen Boyd)

Changes in v6:
- Add required properties for port@0, port@1 and corresponding endpoints (Stephen Boyd)
- Add address-cells and size-cells for ports (Stephen Boyd)
- Use additionalProperties instead of unevaluatedProperties (Stephen Boyd)

Changes in v7:
- Add reference for ports and data-lanes (Rob Herring)
- Add maxItems and minItems for data-lanes (Rob Herring)

Changes in v8:
- Drop common properties and description from ports (Rob Herring)
- Add reference for endpoint (Rob Herring)
- Add correct reference for data-lanes (Rob Herring)
- Drop common properties from required list for ports (Rob Herring)
---

Add YAML schema for the device tree bindings for DSI PHY.

Signed-off-by Krishna Manikandan <[email protected]>

Changes in v1:
- Merge dsi-phy.yaml and dsi-phy-10nm.yaml (Stephen Boyd)
- Remove qcom,dsi-phy-regulator-ldo-mode (Stephen Boyd)
- Add clock cells properly (Stephen Boyd)
- Remove unnecessary decription from clock names (Stephen Boyd)
- Add pin names for the supply entries for 10nm phy which is used in sc7180 and sdm845 (Stephen Boyd)
- Remove unused header files from examples (Stephen Boyd)
- Drop labels for display nodes and correct node name (Stephen Boyd)

Changes in v2:
- Drop maxItems for clock (Stephen Boyd)
- Add vdds supply pin information for sdm845 (Stephen Boyd)
- Add examples for 14nm, 20nm and 28nm phy yaml files (Stephen Boyd)
- Keep child nodes directly under soc node (Stephen Boyd)

Changes in v3:
- Use a separate yaml file to describe the common properties for all the dsi phy versions (Stephen Boyd)
- Remove soc from examples (Stephen Boyd)
- Add description for register property

Changes in v4:
- Modify the title for all the phy versions (Stephen Boyd)
- Drop description for all the phy versions (Stephen Boyd)
- Modify the description for register property (Stephen Boyd)

Changes in v5:
- Remove unused properties from common dsi phy file
- Add clock-cells and phy-cells to required property list (Stephen Boyd)

Changes in v6:
- Add proper compatible string in example

---
 .../bindings/display/msm/dsi-phy-10nm.yaml         | 68 +++++++++++++++++++++
 .../bindings/display/msm/dsi-phy-14nm.yaml         | 66 ++++++++++++++++++++
 .../bindings/display/msm/dsi-phy-20nm.yaml         | 71 ++++++++++++++++++++++
 .../bindings/display/msm/dsi-phy-28nm.yaml         | 68 +++++++++++++++++++++
 .../bindings/display/msm/dsi-phy-common.yaml       | 40 ++++++++++++
 5 files changed, 313 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-10nm.yaml
 create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-14nm.yaml
 create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-20nm.yaml
 create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-28nm.yaml
 create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-common.yaml

Documentation/devicetree/bindings/display/msm/dsi-phy-10nm.yaml new file +26 -0

new file mode 100644
index 0000000..4a26bef
@@ -0,0 +1,68 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dsi-phy-10nm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Display DSI 10nm PHY
+
+maintainers:
+  - Krishna Manikandan <[email protected]>
+
+allOf:
+  - $ref: dsi-phy-common.yaml#
+
+properties:
+  compatible:
+    oneOf:
+      - const: qcom,dsi-phy-10nm
+      - const: qcom,dsi-phy-10nm-8998
+
+  reg:
+    items:
+      - description: dsi phy register set
+      - description: dsi phy lane register set
+      - description: dsi pll register set
+

Add YAML schema for the device tree bindings for DSI PHY.

Signed-off-by Krishna Manikandan <[email protected]>

Changes in v1:
- Merge dsi-phy.yaml and dsi-phy-10nm.yaml (Stephen Boyd)
- Remove qcom,dsi-phy-regulator-ldo-mode (Stephen Boyd)
- Add clock cells properly (Stephen Boyd)
- Remove unnecessary decription from clock names (Stephen Boyd)
- Add pin names for the supply entries for 10nm phy which is used in sc7180 and sdm845 (Stephen Boyd)
- Remove unused header files from examples (Stephen Boyd)
- Drop labels for display nodes and correct node name (Stephen Boyd)

Changes in v2:
- Drop maxItems for clock (Stephen Boyd)
- Add vdds supply pin information for sdm845 (Stephen Boyd)
- Add examples for 14nm, 20nm and 28nm phy yaml files (Stephen Boyd)
- Keep child nodes directly under soc node (Stephen Boyd)

Changes in v3:
- Use a separate yaml file to describe the common properties for all the dsi phy versions (Stephen Boyd)
- Remove soc from examples (Stephen Boyd)
- Add description for register property

Changes in v4:
- Modify the title for all the phy versions (Stephen Boyd)
- Drop description for all the phy versions (Stephen Boyd)
- Modify the description for register property (Stephen Boyd)

Changes in v5:
- Remove unused properties from common dsi phy file
- Add clock-cells and phy-cells to required property list (Stephen Boyd)

Changes in v6:
- Add proper compatible string in example

---
 .../bindings/display/msm/dsi-phy-10nm.yaml         | 68 +++++++++++++++++++++
 .../bindings/display/msm/dsi-phy-14nm.yaml         | 66 ++++++++++++++++++++
 .../bindings/display/msm/dsi-phy-20nm.yaml         | 71 ++++++++++++++++++++++
 .../bindings/display/msm/dsi-phy-28nm.yaml         | 68 +++++++++++++++++++++
 .../bindings/display/msm/dsi-phy-common.yaml       | 40 ++++++++++++
 5 files changed, 313 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-10nm.yaml
 create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-14nm.yaml
 create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-20nm.yaml
 create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-28nm.yaml
 create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-common.yaml

Add YAML schema for the device tree bindings for DSI PHY.

Signed-off-by Krishna Manikandan <[email protected]>

Changes in v1:
- Merge dsi-phy.yaml and dsi-phy-10nm.yaml (Stephen Boyd)
- Remove qcom,dsi-phy-regulator-ldo-mode (Stephen Boyd)
- Add clock cells properly (Stephen Boyd)
- Remove unnecessary decription from clock names (Stephen Boyd)
- Add pin names for the supply entries for 10nm phy which is used in sc7180 and sdm845 (Stephen Boyd)
- Remove unused header files from examples (Stephen Boyd)
- Drop labels for display nodes and correct node name (Stephen Boyd)

Changes in v2:
- Drop maxItems for clock (Stephen Boyd)
- Add vdds supply pin information for sdm845 (Stephen Boyd)
- Add examples for 14nm, 20nm and 28nm phy yaml files (Stephen Boyd)
- Keep child nodes directly under soc node (Stephen Boyd)

Changes in v3:
- Use a separate yaml file to describe the common properties for all the dsi phy versions (Stephen Boyd)
- Remove soc from examples (Stephen Boyd)
- Add description for register property

Changes in v4:
- Modify the title for all the phy versions (Stephen Boyd)
- Drop description for all the phy versions (Stephen Boyd)
- Modify the description for register property (Stephen Boyd)

Changes in v5:
- Remove unused properties from common dsi phy file
- Add clock-cells and phy-cells to required property list (Stephen Boyd)

Changes in v6:
- Add proper compatible string in example
---

Add bindings for Snapdragon DisplayPort controller driver.

Signed-off-by Chandan Uddaraju <[email protected]>

Signed-off-by Vara Reddy <[email protected]>

Signed-off-by Tanmay Shah <[email protected]>

Signed-off-by Kuogee Hsieh <[email protected]>

Signed-off-by Krishna Manikandan <[email protected]>

Changes in V2:
-Provide details about sel-gpio

Changes in V4:

(quoted diff) +0 -2

-Provide details about max dp lanes
-Change the commit text

Changes in V5:
-moved dp.txt to yaml file

Changes in v6:
- Squash all AUX LUT properties into one pattern Property
- Make aux-cfg[0-9]-settings properties optional
- Remove PLL/PHY bindings from DP controller dts
- Add DP clocks description
- Remove _clk suffix from clock names
- Rename pixel clock to stream_pixel
- Remove redundant bindings (GPIO, PHY, HDCP clock, etc..)
- Fix indentation
- Add Display Port as interface of DPU in DPU bindings and add port mapping accordingly.

Chages in v7:
- Add dp-controller.yaml file common between multiple SOC
- Rename dp-sc7180.yaml to dp-controller-sc7180.yaml
- change compatible string and add SOC name to it.
- Remove Root clock generator for pixel clock
- Add assigned-clocks and assigned-clock-parents bindings
- Remove redundant properties, descriptions and blank lines
- Add DP port in DPU bindings
- Update depends-on tag in commit message and rebase change accordingly

Changes in v8:
- Add MDSS AHB clock in bindings

Changes in v9:
- Remove redundant reg-name property
- Change assigned-clocks and assigned-clocks-parents counts to 2
- Use IRQ flags in example dts

Changes in v10:
- Change title of this patch as it does not contain PLL bindings anymore
- Remove redundant properties
- Remove use of IRQ flag
- Fix ports property

Changes in v11:
- add ports required of both #address-cells and #size-cells
- add required operating-points-v2
- add required #sound-dai-cells
- add required power-domains
- update maintainer list

Changes in v12:
- remove soc node from examples (Stephen Boyd)
- split dpu-sc7180.yaml changes to separate patch (Stephen Boyd)

Changes in v13:
- add assigned-clocks
- add assigned-clock-parents

Changes in v14:
- add reference for ports (Rob Herring)

Changes in v15:
- drop common properties from ports (Rob Herring)

---
 .../bindings/display/msm/dp-controller.yaml        | 146 +++++++++++++++++++++
 1 file changed, 146 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/msm/dp-controller.yaml

Documentation/devicetree/bindings/display/msm/dp-controller.yaml new file +146 -0

new file mode 100644
index 0000000..64d8d9e
@@ -0,0 +1,146 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dp-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MSM Display Port Controller
+
+maintainers:
+  - Kuogee Hsieh <[email protected]>
+
+description: |
+  Device tree bindings for DisplayPort host controller for MSM targets
+  that are compatible with VESA DisplayPort interface specification.
+
+properties:
+  compatible:
+    enum:
+      - qcom,sc7180-dp
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: AHB clock to enable register access
+      - description: Display Port AUX clock
+      - description: Display Port Link clock
+      - description: Link interface clock between DP and PHY
+      - description: Display Port Pixel clock
+
+  clock-names:
+    items:
+      - const: core_iface
+      - const: core_aux
+      - const: ctrl_link
+      - const: ctrl_link_iface
+      - const: stream_pixel
+
+  assigned-clocks:
+    items:
+      - description: link clock source
+      - description: pixel clock source
+
+  assigned-clock-parents:
+    items:
+      - description: phy 0 parent
+      - description: phy 1 parent
+
+  phys:
+    maxItems: 1
+
+  phy-names:
+    items:
+      - const: dp
+
+  operating-points-v2:
+    maxItems: 1
+
+  power-domains:
+    maxItems: 1
+
+  "#sound-dai-cells":
+    const: 0
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Input endpoint of the controller
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Output endpoint of the controller
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+  - phys
+  - phy-names
+  - "#sound-dai-cells"
+  - power-domains
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/qcom,dispcc-sc7180.h>
+    #include <dt-bindings/power/qcom-aoss-qmp.h>
+    #include <dt-bindings/power/qcom-rpmpd.h>
+
+    displayport-controller@ae90000 {
+        compatible = "qcom,sc7180-dp";
+        reg = <0xae90000 0x1400>;
+        interrupt-parent = <&mdss>;
+        interrupts = <12>;
+        clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+                 <&dispcc DISP_CC_MDSS_DP_AUX_CLK>,
+                 <&dispcc DISP_CC_MDSS_DP_LINK_CLK>,
+                 <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>,
+                 <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>;
+        clock-names = "core_iface", "core_aux",
+                      "ctrl_link",
+                      "ctrl_link_iface", "stream_pixel";
+
+        assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>,
+                          <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>;
+
+        assigned-clock-parents = <&dp_phy 0>, <&dp_phy 1>;
+
+        phys = <&dp_phy>;
+        phy-names = "dp";
+
+        #sound-dai-cells = <0>;
+
+        power-domains = <&rpmhpd SC7180_CX>;
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+                endpoint {
+                    remote-endpoint = <&dpu_intf0_out>;
+                };
+            };
+
+            port@1 {
+                reg = <1>;
+                endpoint {
+                    remote-endpoint = <&typec>;
+                };
+            };
+        };
+    };
+...

Signature · 1 line

2.7.4

Add bindings for Snapdragon DisplayPort controller driver.

Signed-off-by Chandan Uddaraju <[email protected]>

Signed-off-by Vara Reddy <[email protected]>

Signed-off-by Tanmay Shah <[email protected]>

Signed-off-by Kuogee Hsieh <[email protected]>

Signed-off-by Krishna Manikandan <[email protected]>

Changes in V2:
-Provide details about sel-gpio

Changes in V4:

(quoted diff) +0 -2

-Provide details about max dp lanes
-Change the commit text

Changes in V5:
-moved dp.txt to yaml file

Changes in v6:
- Squash all AUX LUT properties into one pattern Property
- Make aux-cfg[0-9]-settings properties optional
- Remove PLL/PHY bindings from DP controller dts
- Add DP clocks description
- Remove _clk suffix from clock names
- Rename pixel clock to stream_pixel
- Remove redundant bindings (GPIO, PHY, HDCP clock, etc..)
- Fix indentation
- Add Display Port as interface of DPU in DPU bindings and add port mapping accordingly.

Chages in v7:
- Add dp-controller.yaml file common between multiple SOC
- Rename dp-sc7180.yaml to dp-controller-sc7180.yaml
- change compatible string and add SOC name to it.
- Remove Root clock generator for pixel clock
- Add assigned-clocks and assigned-clock-parents bindings
- Remove redundant properties, descriptions and blank lines
- Add DP port in DPU bindings
- Update depends-on tag in commit message and rebase change accordingly

Changes in v8:
- Add MDSS AHB clock in bindings

Changes in v9:
- Remove redundant reg-name property
- Change assigned-clocks and assigned-clocks-parents counts to 2
- Use IRQ flags in example dts

Changes in v10:
- Change title of this patch as it does not contain PLL bindings anymore
- Remove redundant properties
- Remove use of IRQ flag
- Fix ports property

Changes in v11:
- add ports required of both #address-cells and #size-cells
- add required operating-points-v2
- add required #sound-dai-cells
- add required power-domains
- update maintainer list

Changes in v12:
- remove soc node from examples (Stephen Boyd)
- split dpu-sc7180.yaml changes to separate patch (Stephen Boyd)

Changes in v13:
- add assigned-clocks
- add assigned-clock-parents

Changes in v14:
- add reference for ports (Rob Herring)

Changes in v15:
- drop common properties from ports (Rob Herring)

---
 .../bindings/display/msm/dp-controller.yaml        | 146 +++++++++++++++++++++
 1 file changed, 146 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/msm/dp-controller.yaml

Add bindings for Snapdragon DisplayPort controller driver.

Signed-off-by Chandan Uddaraju <[email protected]>

Signed-off-by Vara Reddy <[email protected]>

Signed-off-by Tanmay Shah <[email protected]>

Signed-off-by Kuogee Hsieh <[email protected]>

Signed-off-by Krishna Manikandan <[email protected]>

Changes in V2:
-Provide details about sel-gpio

Changes in V4:

(quoted diff) +0 -2

-Provide details about max dp lanes
-Change the commit text

Changes in V5:
-moved dp.txt to yaml file

Changes in v6:
- Squash all AUX LUT properties into one pattern Property
- Make aux-cfg[0-9]-settings properties optional
- Remove PLL/PHY bindings from DP controller dts
- Add DP clocks description
- Remove _clk suffix from clock names
- Rename pixel clock to stream_pixel
- Remove redundant bindings (GPIO, PHY, HDCP clock, etc..)
- Fix indentation
- Add Display Port as interface of DPU in DPU bindings and add port mapping accordingly.

Chages in v7:
- Add dp-controller.yaml file common between multiple SOC
- Rename dp-sc7180.yaml to dp-controller-sc7180.yaml
- change compatible string and add SOC name to it.
- Remove Root clock generator for pixel clock
- Add assigned-clocks and assigned-clock-parents bindings
- Remove redundant properties, descriptions and blank lines
- Add DP port in DPU bindings
- Update depends-on tag in commit message and rebase change accordingly

Changes in v8:
- Add MDSS AHB clock in bindings

Changes in v9:
- Remove redundant reg-name property
- Change assigned-clocks and assigned-clocks-parents counts to 2
- Use IRQ flags in example dts

Changes in v10:
- Change title of this patch as it does not contain PLL bindings anymore
- Remove redundant properties
- Remove use of IRQ flag
- Fix ports property

Changes in v11:
- add ports required of both #address-cells and #size-cells
- add required operating-points-v2
- add required #sound-dai-cells
- add required power-domains
- update maintainer list

Changes in v12:
- remove soc node from examples (Stephen Boyd)
- split dpu-sc7180.yaml changes to separate patch (Stephen Boyd)

Changes in v13:
- add assigned-clocks
- add assigned-clock-parents

Changes in v14:
- add reference for ports (Rob Herring)

Changes in v15:
- drop common properties from ports (Rob Herring)
---

Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml +0 -0

Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml +6 -0

+      ports:
+        $ref: /schemas/graph.yaml#/properties/ports
+        description: |
+          Contains the list of output ports from DPU device. These ports
+          connect to interfaces that are external to the DPU hardware,
+          such as DSI, DP etc. Each output port contains an endpoint that

Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml +82 -0

+
+    required:
+      - compatible
+      - reg
+      - reg-names
+      - clocks
+      - interrupts
+      - power-domains
+      - operating-points-v2
+      - ports
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - power-domains
+  - clocks
+  - interrupts
+  - interrupt-controller
+  - iommus
+  - ranges
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,dispcc-sc7180.h>
+    #include <dt-bindings/clock/qcom,gcc-sc7180.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interconnect/qcom,sdm845.h>
+    #include <dt-bindings/power/qcom-rpmpd.h>
+
+    display-subsystem@ae00000 {
+         #address-cells = <1>;
+         #size-cells = <1>;
+         compatible = "qcom,sc7180-mdss";
+         reg = <0xae00000 0x1000>;
+         reg-names = "mdss";
+         power-domains = <&dispcc MDSS_GDSC>;
+         clocks = <&gcc GCC_DISP_AHB_CLK>,
+                  <&dispcc DISP_CC_MDSS_AHB_CLK>,
+                  <&dispcc DISP_CC_MDSS_MDP_CLK>;
+         clock-names = "iface", "ahb", "core";
+
+         interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+         interrupt-controller;
+         #interrupt-cells = <1>;
+
+         interconnects = <&mmss_noc MASTER_MDP0 &mc_virt SLAVE_EBI1>;
+         interconnect-names = "mdp0-mem";
+
+         iommus = <&apps_smmu 0x800 0x2>;
+         ranges;
+
+         display-controller@ae01000 {
+                   compatible = "qcom,sc7180-dpu";
+                   reg = <0x0ae01000 0x8f000>,
+                         <0x0aeb0000 0x2008>;
+
+                   reg-names = "mdp", "vbif";
+
+                   clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
+                            <&dispcc DISP_CC_MDSS_AHB_CLK>,
+                            <&dispcc DISP_CC_MDSS_ROT_CLK>,
+                            <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+                            <&dispcc DISP_CC_MDSS_MDP_CLK>,
+                            <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+                   clock-names = "bus", "iface", "rot", "lut", "core",
+                                 "vsync";
+
+                   interrupt-parent = <&mdss>;
+                   interrupts = <0>;
+                   power-domains = <&rpmhpd SC7180_CX>;
+                   operating-points-v2 = <&mdp_opp_table>;
+
+                   ports {
+                           #address-cells = <1>;
+                           #size-cells = <0>;
+
+                           port@0 {
+                                   reg = <0>;
+                                   dpu_intf1_out: endpoint {

Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml +4 -0

+                   };
+         };
+    };
+...

Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml new file +92 -0

new file mode 100644
index 0000000..b4ea7c9
@@ -0,0 +1,212 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dpu-sdm845.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Display DPU dt properties for SDM845 target
+
+maintainers:
+  - Krishna Manikandan <[email protected]>
+
+description: |
+  Device tree bindings for MSM Mobile Display Subsystem(MDSS) that encapsulates
+  sub-blocks like DPU display controller, DSI and DP interfaces etc. Device tree
+  bindings of MDSS and DPU are mentioned for SDM845 target.
+
+properties:
+  compatible:
+    items:
+      - const: qcom,sdm845-mdss
+
+  reg:
+    maxItems: 1
+
+  reg-names:
+    const: mdss
+
+  power-domains:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Display AHB clock from gcc
+      - description: Display AXI clock
+      - description: Display core clock
+
+  clock-names:
+    items:
+      - const: iface
+      - const: bus
+      - const: core
+
+  interrupts:
+    maxItems: 1
+
+  interrupt-controller: true
+
+  "#address-cells": true
+
+  "#size-cells": true
+
+  "#interrupt-cells":
+    const: 1
+
+  iommus:
+    items:
+      - description: Phandle to apps_smmu node with SID mask for Hard-Fail port0
+      - description: Phandle to apps_smmu node with SID mask for Hard-Fail port1
+
+  ranges: true
+
+patternProperties:
+  "^display-controller@[0-9a-f]+$":
+    type: object
+    description: Node containing the properties of DPU.
+
+    properties:
+      compatible:
+        items:
+          - const: qcom,sdm845-dpu
+
+      reg:
+        items:
+          - description: Address offset and size for mdp register set
+          - description: Address offset and size for vbif register set
+
+      reg-names:
+        items:
+          - const: mdp
+          - const: vbif
+
+      clocks:
+        items:
+          - description: Display ahb clock
+          - description: Display axi clock
+          - description: Display core clock
+          - description: Display vsync clock
+
+      clock-names:
+        items:
+          - const: iface
+          - const: bus

Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml new file +10 -0

+      ports:
+        $ref: /schemas/graph.yaml#/properties/ports
+        description: |
+          Contains the list of output ports from DPU device. These ports
+          connect to interfaces that are external to the DPU hardware,
+          such as DSI, DP etc. Each output port contains an endpoint that
+          describes how it is connected to an external interface.
+
+        properties:
+          port@0:

Quoted 1 line · Krishna Manikandan

Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml +0 -0

[..]

Quoted 6 lines

Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml +6 -0

+      ports:
+        $ref: /schemas/graph.yaml#/properties/ports
+        description: |
+          Contains the list of output ports from DPU device. These ports
+          connect to interfaces that are external to the DPU hardware,
+          such as DSI, DP etc. Each output port contains an endpoint that

Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml line 129

Quoted 10 lines

Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml +10 -0

+          describes how it is connected to an external interface.
+
+        properties:
+          port@0:
+            $ref: /schemas/graph.yaml#/properties/port
+            description: DPU_INTF1 (DSI1)
+
+          port@2:
+            $ref: /schemas/graph.yaml#/properties/port
+            description: DPU_INTF0 (DP)

Why is port@0 INTF1 and why is port@2 INTF0? In the binding you're translating the two ports that are described are 0 and 1, representing INTF1 and INTF2, or DSI1 and DSI2, respectively.

Further more, I have a need for somehow describing the pairing of 4 DP INTFs (INTF 0, 3, 4 and 5) and how they are connected to the 3+1 DP+eDP controllers.

Downstream this seems to be handled by adding cell-index to the DP controllers and then matching that against the numbering in the driver's INTF array. But rather than adding cell-index to map this, can't we define that the port index is the INTF-number here?

This would obviously break compatibility with existing DTBs, but we could start by doing it selectively for the new compatibles, fix up the existing dts files and then drop the selective application after 1 or 2 LTS releases.

Quoted 1 line

+examples:

Quoted 7 lines

Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml +7 -0

+                   ports {
+                           #address-cells = <1>;
+                           #size-cells = <0>;
+
+                           port@0 {
+                                   reg = <0>;
+                                   dpu_intf1_out: endpoint {

Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml line 224

Quoted 10 lines

Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml +10 -0

+                                                  remote-endpoint = <&dsi0_in>;
+                                   };
+                           };
+
+                            port@2 {
+                                    reg = <2>;
+                                    dpu_intf0_out: endpoint {
+                                                   remote-endpoint = <&dp_in>;
+                                    };
+                            };

The indentation is inconsistent among the ports.

Quoted 5 lines

Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml +4 -0

+                   };
+         };
+    };
+...

Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml +0 -0

Quoted 1 line

+ operating-points-v2: true

You have a blank line between all other properties, but not here.

Quoted 1 line

+ ports:

Quoted 1 line

Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml +0 -0

[..]

Quoted 6 lines

Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml +6 -0

+      ports:
+        $ref: /schemas/graph.yaml#/properties/ports
+        description: |
+          Contains the list of output ports from DPU device. These ports
+          connect to interfaces that are external to the DPU hardware,
+          such as DSI, DP etc. Each output port contains an endpoint that

Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml line 129

Quoted 10 lines

Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml +10 -0

+          describes how it is connected to an external interface.
+
+        properties:
+          port@0:
+            $ref: /schemas/graph.yaml#/properties/port
+            description: DPU_INTF1 (DSI1)
+
+          port@2:
+            $ref: /schemas/graph.yaml#/properties/port
+            description: DPU_INTF0 (DP)

Why is port@0 INTF1 and why is port@2 INTF0? In the binding you're translating the two ports that are described are 0 and 1, representing INTF1 and INTF2, or DSI1 and DSI2, respectively.

Further more, I have a need for somehow describing the pairing of 4 DP INTFs (INTF 0, 3, 4 and 5) and how they are connected to the 3+1 DP+eDP controllers.

Downstream this seems to be handled by adding cell-index to the DP controllers and then matching that against the numbering in the driver's INTF array. But rather than adding cell-index to map this, can't we define that the port index is the INTF-number here?

This would obviously break compatibility with existing DTBs, but we could start by doing it selectively for the new compatibles, fix up the existing dts files and then drop the selective application after 1 or 2 LTS releases.

Quoting Bjorn Andersson (2021-05-21 09:00:29)

Quoted 34 lines · Krishna Manikandan

Quoted 1 line

Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml +0 -0

[..]

Quoted 6 lines

Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml +6 -0

+      ports:
+        $ref: /schemas/graph.yaml#/properties/ports
+        description: |
+          Contains the list of output ports from DPU device. These ports
+          connect to interfaces that are external to the DPU hardware,
+          such as DSI, DP etc. Each output port contains an endpoint that

Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml line 129

Quoted 10 lines

Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml +10 -0

+          describes how it is connected to an external interface.
+
+        properties:
+          port@0:
+            $ref: /schemas/graph.yaml#/properties/port
+            description: DPU_INTF1 (DSI1)
+
+          port@2:
+            $ref: /schemas/graph.yaml#/properties/port
+            description: DPU_INTF0 (DP)

Why is port@0 INTF1 and why is port@2 INTF0? In the binding you're translating the two ports that are described are 0 and 1, representing INTF1 and INTF2, or DSI1 and DSI2, respectively.

Further more, I have a need for somehow describing the pairing of 4 DP INTFs (INTF 0, 3, 4 and 5) and how they are connected to the 3+1 DP+eDP controllers.

Downstream this seems to be handled by adding cell-index to the DP controllers and then matching that against the numbering in the driver's INTF array. But rather than adding cell-index to map this, can't we define that the port index is the INTF-number here?

Quoted 4 lines

This would obviously break compatibility with existing DTBs, but we could start by doing it selectively for the new compatibles, fix up the existing dts files and then drop the selective application after 1 or 2 LTS releases.

I requested that the existing DT not change a while ago when the DP interface was being added to this binding. Is it possible to figure out what interface it is that the port is for from the binding? It feels like the problem is that the driver wants to look through the graph and make connectors for each one, but it doesn't know what type of connector to make.

MSM Mobile Display Subsystem (MDSS) encapsulates sub-blocks like DPU display controller, DSI etc. Add YAML schema for DPU device tree bindings.

Signed-off-by Krishna Manikandan <[email protected]>

Changes in v2:
- Changed dpu to DPU (Sam Ravnborg)
- Fixed indentation issues (Sam Ravnborg)
- Added empty line between different properties (Sam Ravnborg)
- Replaced reference txt files with their corresponding yaml files (Sam Ravnborg)
- Modified the file to use "|" only when it is necessary (Sam Ravnborg)

Changes in v3:
- Corrected the license used (Rob Herring)
- Added maxItems for properties (Rob Herring)
- Dropped generic descriptions (Rob Herring)
- Added ranges property (Rob Herring)
- Corrected the indendation (Rob Herring)
- Added additionalProperties (Rob Herring)
- Split dsi file into two, one for dsi controller and another one for dsi phy per target (Rob Herring)
- Corrected description for pinctrl-names (Rob Herring)
- Corrected the examples used in yaml file (Rob Herring)
- Delete dsi.txt and dpu.txt (Rob Herring)

Changes in v4:
- Move schema up by one level (Rob Herring)
- Add patternProperties for mdp node (Rob Herring)
- Corrected description of some properties (Rob Herring)

Changes in v5:
- Correct the indentation (Rob Herring)
- Remove unnecessary description from properties (Rob Herring)
- Correct the number of interconnect entries (Rob Herring)
- Add interconnect names for sc7180 (Rob Herring)
- Add description for ports (Rob Herring)
- Remove common properties (Rob Herring)
- Add unevalutatedProperties (Rob Herring)
- Reference existing dsi controller yaml in the common dsi controller file (Rob Herring)
- Correct the description of clock names to include only the clocks that are required (Rob Herring)
- Remove properties which are already covered under the common binding (Rob Herring)
- Add dsi phy supply nodes which are required for sc7180 and sdm845 targets (Rob Herring)
- Add type ref for syscon-sfpb (Rob Herring)

Changes in v6:
- Fixed errors during dt_binding_check (Rob Herring)
- Add maxItems for phys and phys-names (Rob Herring)
- Use unevaluatedProperties wherever required (Rob Herring)
- Removed interrupt controller from required properties for dsi controller (Rob Herring)
- Add constraints for dsi-phy reg-names based on the compatible phy version (Rob Herring)
- Add constraints for dsi-phy supply nodes based on the compatible phy version (Rob Herring)

Changes in v7:
- Add default value for qcom,mdss-mdp-transfer-time-us (Rob Herring)
- Modify the schema for data-lanes (Rob Herring)
- Split the phy schema into separate schemas based on the phy version (Rob Herring)

Changes in v8:
- Resolve merge conflicts with latest dsi.txt file
- Include dp yaml change also in the same series

Changes in v9:
- Combine target specific dsi controller yaml files to a single yaml file (Rob Herring)
- Combine target specific dsi phy yaml files into a single yaml file (Rob Herring)
- Use unevaluatedProperties and additionalProperties wherever required
- Remove duplicate properties from common yaml files

Changes in v10:
- Split the patch into separate patches for DPU, DSI and PHY (Stephen Boyd)
- Drop unnecessary fullstop (Stephen Boyd)
- Add newline whereever required (Stephen Boyd)
- Add description for clock used (Stephen Boyd)
- Modify the description for interconnect entries (Stephen Boyd)
- Drop assigned clock entries as it a generic property (Stephen Boyd)
- Correct the definition for interrupts (Stephen Boyd)
- Drop clock names from required properties (Stephen Boyd)
- Drop labels for display nodes from example (Stephen Boyd)
- Drop flags from interrupts entries (Stephen Boyd)

Changes in v11:
- Drop maxItems for clocks (Stephen Boyd)

Changes in v12:
- Add description for register property (Stephen Boyd)
- Add maxItems for interrupts (Stephen Boyd)
- Add description for iommus property (Stephen Boyd)
- Add description for interconnects (Stephen Boyd)
- Change display node name to display_controller (Stephen Boyd)

Changes in v13:
- Add maxItems for reg property (Stephen Boyd)
- Add ranges property in example (Stephen Boyd)
- Modify description for iommus property (Stephen Boyd)
- Add Dp bindings for ports in the same patch (Stephen Boyd)
- Remove soc from examples and change address and size cells accordingly (Stephen Boyd)
- Add reference for ports

Changes in v14:
- Modify title for SC7180 and SDM845 yaml files (Stephen Boyd)
- Add required list for display-controller node (Stephen Boyd)

Changes in v16:
- Add reference for port (Rob Herring)
- Make additionalProperties as false (Rob Herring)

---
 .../bindings/display/msm/dpu-sc7180.yaml           | 228 +++++++++++++++++++++
 .../bindings/display/msm/dpu-sdm845.yaml           | 212 +++++++++++++++++++
 .../devicetree/bindings/display/msm/dpu.txt        | 141 -------------
 3 files changed, 440 insertions(+), 141 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml
 create mode 100644 Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml
 delete mode 100644 Documentation/devicetree/bindings/display/msm/dpu.txt

MSM Mobile Display Subsystem (MDSS) encapsulates sub-blocks like DPU display controller, DSI etc. Add YAML schema for DPU device tree bindings.

Signed-off-by Krishna Manikandan <[email protected]>

Changes in v2:
- Changed dpu to DPU (Sam Ravnborg)
- Fixed indentation issues (Sam Ravnborg)
- Added empty line between different properties (Sam Ravnborg)
- Replaced reference txt files with their corresponding yaml files (Sam Ravnborg)
- Modified the file to use "|" only when it is necessary (Sam Ravnborg)

Changes in v3:
- Corrected the license used (Rob Herring)
- Added maxItems for properties (Rob Herring)
- Dropped generic descriptions (Rob Herring)
- Added ranges property (Rob Herring)
- Corrected the indendation (Rob Herring)
- Added additionalProperties (Rob Herring)
- Split dsi file into two, one for dsi controller and another one for dsi phy per target (Rob Herring)
- Corrected description for pinctrl-names (Rob Herring)
- Corrected the examples used in yaml file (Rob Herring)
- Delete dsi.txt and dpu.txt (Rob Herring)

Changes in v4:
- Move schema up by one level (Rob Herring)
- Add patternProperties for mdp node (Rob Herring)
- Corrected description of some properties (Rob Herring)

Changes in v5:
- Correct the indentation (Rob Herring)
- Remove unnecessary description from properties (Rob Herring)
- Correct the number of interconnect entries (Rob Herring)
- Add interconnect names for sc7180 (Rob Herring)
- Add description for ports (Rob Herring)
- Remove common properties (Rob Herring)
- Add unevalutatedProperties (Rob Herring)
- Reference existing dsi controller yaml in the common dsi controller file (Rob Herring)
- Correct the description of clock names to include only the clocks that are required (Rob Herring)
- Remove properties which are already covered under the common binding (Rob Herring)
- Add dsi phy supply nodes which are required for sc7180 and sdm845 targets (Rob Herring)
- Add type ref for syscon-sfpb (Rob Herring)

Changes in v6:
- Fixed errors during dt_binding_check (Rob Herring)
- Add maxItems for phys and phys-names (Rob Herring)
- Use unevaluatedProperties wherever required (Rob Herring)
- Removed interrupt controller from required properties for dsi controller (Rob Herring)
- Add constraints for dsi-phy reg-names based on the compatible phy version (Rob Herring)
- Add constraints for dsi-phy supply nodes based on the compatible phy version (Rob Herring)

Changes in v7:
- Add default value for qcom,mdss-mdp-transfer-time-us (Rob Herring)
- Modify the schema for data-lanes (Rob Herring)
- Split the phy schema into separate schemas based on the phy version (Rob Herring)

Changes in v8:
- Resolve merge conflicts with latest dsi.txt file
- Include dp yaml change also in the same series

Changes in v9:
- Combine target specific dsi controller yaml files to a single yaml file (Rob Herring)
- Combine target specific dsi phy yaml files into a single yaml file (Rob Herring)
- Use unevaluatedProperties and additionalProperties wherever required
- Remove duplicate properties from common yaml files

Changes in v10:
- Split the patch into separate patches for DPU, DSI and PHY (Stephen Boyd)
- Drop unnecessary fullstop (Stephen Boyd)
- Add newline whereever required (Stephen Boyd)
- Add description for clock used (Stephen Boyd)
- Modify the description for interconnect entries (Stephen Boyd)
- Drop assigned clock entries as it a generic property (Stephen Boyd)
- Correct the definition for interrupts (Stephen Boyd)
- Drop clock names from required properties (Stephen Boyd)
- Drop labels for display nodes from example (Stephen Boyd)
- Drop flags from interrupts entries (Stephen Boyd)

Changes in v11:
- Drop maxItems for clocks (Stephen Boyd)

Changes in v12:
- Add description for register property (Stephen Boyd)
- Add maxItems for interrupts (Stephen Boyd)
- Add description for iommus property (Stephen Boyd)
- Add description for interconnects (Stephen Boyd)
- Change display node name to display_controller (Stephen Boyd)

Changes in v13:
- Add maxItems for reg property (Stephen Boyd)
- Add ranges property in example (Stephen Boyd)
- Modify description for iommus property (Stephen Boyd)
- Add Dp bindings for ports in the same patch (Stephen Boyd)
- Remove soc from examples and change address and size cells accordingly (Stephen Boyd)
- Add reference for ports

Changes in v14:
- Modify title for SC7180 and SDM845 yaml files (Stephen Boyd)
- Add required list for display-controller node (Stephen Boyd)

Changes in v16:
- Add reference for port (Rob Herring)
- Make additionalProperties as false (Rob Herring)
---