arm64: dts: ti: k3-j7200-common-proc-board fixes
Subsystems (2)
v3 cover arm64: dts: ti: k3-j7200-common-proc-board fixes
This patch series fixes the pin mux configuration and enable wkup_i2c0 at board level.
Note to self: in u-boot i2c pin mux is set in R5 board file. which will moved to som file, Fix that too when syncing kernel and uboot DTS files.
Changes since v2:
https://lore.kernel.org/all/[email protected]/
Pin Mux (Patch 1/1):
- No Change
wkup_i2c:
- Added pin mux
- Added speed
Changes since v1:
https://lore.kernel.org/all/[email protected]/
Pin mux:
- Fixed commit message and author
wkup_i2c:
- Removed Fixes tag in commit message
- Moved wkup_i2c in som instead of common board
- Added eeprom as child device
Keerthy (1):
arm64: dts: ti: k3-j7200: Fix physical address of pin
Udit Kumar (1):
arm64: dts: ti: k3-j7200-som: Enable I2C
.../dts/ti/k3-j7200-common-proc-board.dts | 28 +++++++++---------- arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 21 ++++++++++++++ 2 files changed, 35 insertions(+), 14 deletions(-)
Signature · 1 line
2.34.1
PATCH v3 1/2 arm64: dts: ti: k3-j7200: Fix physical address of pin
From: Keerthy <[email protected]>
wkup_pmx splits into multiple regions. Like
wkup_pmx0 -> 13 pins (WKUP_PADCONFIG 0 - 12)
wkup_pmx1 -> 2 pins (WKUP_PADCONFIG 14 - 15)
wkup_pmx2 -> 59 pins (WKUP_PADCONFIG 26 - 84)
wkup_pmx3 -> 8 pins (WKUP_PADCONFIG 93 - 100)With this split, pin offset needs to be adjusted to match with new pmx for all pins above wkup_pmx0.
Example a pin under wkup_pmx1 should start from 0 instead of old offset(0x38 WKUP_PADCONFIG 14 offset)
J7200 Datasheet (Table 6-106, Section 6.4 Pin Multiplexing) :
https://www.ti.com/lit/ds/symlink/dra821u.pdf
--- .../dts/ti/k3-j7200-common-proc-board.dts | 28 +++++++++---------- 1 file changed, 14 insertions(+), 14 deletions(-)
arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts +14 -14
@@ -83,25 +83,25 @@ vdd_sd_dv: gpio-regulator-TLV71033 { &wkup_pmx2 { mcu_cpsw_pins_default: mcu-cpsw-pins-default { pinctrl-single,pins = < - J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */ - J721E_WKUP_IOPAD(0x006c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */ - J721E_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */ - J721E_WKUP_IOPAD(0x0074, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */ - J721E_WKUP_IOPAD(0x0078, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */ - J721E_WKUP_IOPAD(0x007c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */ - J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */ - J721E_WKUP_IOPAD(0x008c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */ - J721E_WKUP_IOPAD(0x0090, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */ - J721E_WKUP_IOPAD(0x0094, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */ - J721E_WKUP_IOPAD(0x0080, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */ - J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RXC */ + J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */ + J721E_WKUP_IOPAD(0x0004, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */ + J721E_WKUP_IOPAD(0x0008, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */ + J721E_WKUP_IOPAD(0x000c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */ + J721E_WKUP_IOPAD(0x0010, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */ + J721E_WKUP_IOPAD(0x0014, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */ + J721E_WKUP_IOPAD(0x0020, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */ + J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */ + J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */ + J721E_WKUP_IOPAD(0x002c, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */ + J721E_WKUP_IOPAD(0x0018, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */ + J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* MCU_RGMII1_RXC */ >; }; mcu_mdio_pins_default: mcu-mdio1-pins-default { pinctrl-single,pins = < - J721E_WKUP_IOPAD(0x009c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */ - J721E_WKUP_IOPAD(0x0098, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */ + J721E_WKUP_IOPAD(0x0034, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */ + J721E_WKUP_IOPAD(0x0030, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */ >; }; };
Signature · 1 line
2.34.1
PATCH v3 2/2 arm64: dts: ti: k3-j7200-som: Enable I2C
In reply to Udit KumarThis patch enables wkup_i2c0 node in board dts file along with pin mux and speed.
Also enables underneath eeprom CAV24C256WE.
J7200 Datasheet (Table 6-106, Section 6.4 Pin Multiplexing) :
https://www.ti.com/lit/ds/symlink/dra821u.pdf
J7200 User Guide (Section 4.3, Table 4-2) :
https://www.ti.com/lit/ug/spruiw7a/spruiw7a.pdf
--- arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+)
arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi +21 -0
@@ -118,6 +118,15 @@ J721E_WKUP_IOPAD(0x0008, PIN_INPUT, 0) /* MCU_OSPI0_DQS */ }; }; +&wkup_pmx2 { + wkup_i2c0_pins_default: wkup-i2c0-pins-default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0x98, PIN_INPUT_PULLUP, 0) /* (F20) WKUP_I2C0_SCL */ + J721E_WKUP_IOPAD(0x9c, PIN_INPUT_PULLUP, 0) /* (H21) WKUP_I2C0_SDA */ + >; + }; +}; + &main_pmx0 { main_i2c0_pins_default: main-i2c0-pins-default { pinctrl-single,pins = <
@@ -214,6 +223,18 @@ exp_som: gpio@21 { }; }; +&wkup_i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&wkup_i2c0_pins_default>; + clock-frequency = <400000>; + + eeprom@50 { + compatible = "atmel,24c256"; + reg = <0x50>; + }; +}; + &ospi0 { pinctrl-names = "default"; pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
Signature · 1 line
2.34.1
Hi Udit Kumar,
Quoted 8 lines · Udit Kumar
This patch series fixes the pin mux configuration and enable
wkup_i2c0at board level.Note to self: in u-boot i2c pin mux is set in R5 board file. which will moved to som file, Fix that too when syncing kernel and uboot DTS files.
[...]
I have applied the following to branch ti-k3-dts-next on [1]. Thank you!
[1/2] arm64: dts: ti: k3-j7200: Fix physical address of pin
commit: 3d011933000ed9054c649952d83162d24f020a93
[2/2] arm64: dts: ti: k3-j7200-som: Enable I2C
commit: 2f932d4151599bc647607ae841cf57273279168cAll being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent up the chain during the next merge window (or sooner if it is a relevant bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git
--
Vignesh