sh: passing FDT address to kernel startup.
Subsystems (15)
A message that is not in the archive (sent off-list or not yet received): [email protected]
Yoshinori Sato
maintainerPATCH RESEND v7 1/37 sh: passing FDT address to kernel startup.
R4 is caller saved in SH ABI.
Save it so it doesn't get corrupted until it's needed for initialization.
--- arch/sh/boot/compressed/head_32.S | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
arch/sh/boot/compressed/head_32.S +3 -2
@@ -15,7 +15,8 @@ startup: /* Load initial status register */ mov.l init_sr, r1 ldc r1, sr - + /* Save FDT address */ + mov r4, r13 /* Move myself to proper location if necessary */ mova 1f, r0 mov.l 1f, r2
@@ -84,7 +85,7 @@ l1: /* Jump to the start of the decompressed kernel */ mov.l kernel_start_addr, r0 jmp @r0 - nop + mov r13, r4 .align 2 bss_start_addr:
Signature · 1 line
2.39.2
Yoshinori Sato
maintainerPATCH RESEND v7 2/37 sh: Kconfig unified OF supported targets.
In reply to a message not in the archiveTargets that support OF should be treated as one board.
--- arch/sh/Kconfig | 1 + arch/sh/boards/Kconfig | 23 +++++++++++++---------- 2 files changed, 14 insertions(+), 10 deletions(-)
arch/sh/Kconfig +1 -0
@@ -711,6 +711,7 @@ choice prompt "Kernel command line" optional default CMDLINE_OVERWRITE + depends on !OF || USE_BUILTIN_DTB help Setting this option allows the kernel command line arguments to be set.
arch/sh/boards/Kconfig +13 -10
@@ -19,16 +19,9 @@ config SH_DEVICE_TREE select TIMER_OF select COMMON_CLK select GENERIC_CALIBRATE_DELAY - -config SH_JCORE_SOC - bool "J-Core SoC" - select SH_DEVICE_TREE - select CLKSRC_JCORE_PIT - select JCORE_AIC - depends on CPU_J2 - help - Select this option to include drivers core components of the - J-Core SoC, including interrupt controllers and timers. + select GENERIC_IRQ_CHIP + select SYS_SUPPORTS_PCI + select GENERIC_PCI_IOMAP if PCI config SH_SOLUTION_ENGINE bool "SolutionEngine"
@@ -293,6 +286,7 @@ config SH_LANDISK bool "LANDISK" depends on CPU_SUBTYPE_SH7751R select HAVE_PCI + select SYS_SUPPORTS_PCI help I-O DATA DEVICE, INC. "LANDISK Series" support.
@@ -369,6 +363,15 @@ config SH_APSH4AD0A help Select AP-SH4AD-0A if configuring for an ALPHAPROJECT AP-SH4AD-0A. +config SH_OF_BOARD + bool "General Open Firmware boards" + select SH_DEVICE_TREE + select CLKSRC_JCORE_PIT if CPU_J2 + select JCORE_AIC if CPU_J2 + select HAVE_PCI if CPU_SUBTYPE_SH7751R + help + This board means general OF supported targets. + source "arch/sh/boards/mach-r2d/Kconfig" source "arch/sh/boards/mach-highlander/Kconfig" source "arch/sh/boards/mach-sdk7780/Kconfig"
Signature · 1 line
2.39.2
Yoshinori Sato
maintainerPATCH RESEND v7 3/37 sh: Enable OF support for build and configuration.
In reply to a message not in the archiveIRQ, CLK and PCI will be migrated to a common driver framework. So if OF, disable the SH specific drivers.
--- arch/sh/Kconfig | 11 ++++++----- arch/sh/drivers/Makefile | 2 ++ arch/sh/kernel/cpu/Makefile | 9 +++++++-- arch/sh/kernel/cpu/sh4/Makefile | 3 +++ 4 files changed, 18 insertions(+), 7 deletions(-)
arch/sh/Kconfig +6 -5
@@ -66,10 +66,10 @@ config SUPERH select MODULES_USE_ELF_RELA select NEED_SG_DMA_LENGTH select NO_DMA if !MMU && !DMA_COHERENT - select NO_GENERIC_PCI_IOPORT_MAP if PCI + select NO_GENERIC_PCI_IOPORT_MAP if !SH_DEVICE_TREE select OLD_SIGACTION select OLD_SIGSUSPEND - select PCI_DOMAINS if PCI + select PCI_DOMAINS if PCI && !SH_DEVICE_TREE select PERF_EVENTS select PERF_USE_VMALLOC select RTC_LIB
@@ -153,7 +153,7 @@ menu "System type" # config CPU_SH2 bool - select SH_INTC + select SH_INTC if !SH_DEVICE_TREE config CPU_SH2A bool
@@ -179,7 +179,7 @@ config CPU_SH4 select CPU_HAS_INTEVT select CPU_HAS_SR_RB select CPU_HAS_FPU if !CPU_SH4AL_DSP - select SH_INTC + select SH_INTC if !SH_DEVICE_TREE select SYS_SUPPORTS_SH_TMU config CPU_SH4A
@@ -522,6 +522,7 @@ config SH_PCLK_FREQ config SH_CLK_CPG def_bool y + depends on !COMMON_CLK config SH_CLK_CPG_LEGACY depends on SH_CLK_CPG
@@ -666,7 +667,7 @@ config BUILTIN_DTB_SOURCE kernel. config ZERO_PAGE_OFFSET - hex + hex "Zero page offset" default "0x00010000" if PAGE_SIZE_64KB || SH_RTS7751R2D || \ SH_7751_SOLUTION_ENGINE default "0x00004000" if PAGE_SIZE_16KB || SH_SH03
arch/sh/drivers/Makefile +2 -0
@@ -5,6 +5,8 @@ obj-y += dma/ platform_early.o +ifndef CONFIG_SH_DEVICE_TREE obj-$(CONFIG_PCI) += pci/ +endif obj-$(CONFIG_PUSH_SWITCH) += push-switch.o obj-$(CONFIG_HEARTBEAT) += heartbeat.o
arch/sh/kernel/cpu/Makefile +7 -2
@@ -16,6 +16,11 @@ obj-$(CONFIG_ARCH_SHMOBILE) += shmobile/ # Common interfaces. obj-$(CONFIG_SH_ADC) += adc.o +ifndef CONFIG_COMMON_CLK +obj-y += clock.o obj-$(CONFIG_SH_CLK_CPG_LEGACY) += clock-cpg.o - -obj-y += irq/ init.o clock.o fpu.o pfc.o proc.o +endif +ifndef CONFIG_GENERIC_IRQ_CHIP +obj-y += irq/ +endif +obj-y += init.o fpu.o pfc.o proc.o
arch/sh/kernel/cpu/sh4/Makefile +3 -0
@@ -15,6 +15,7 @@ perf-$(CONFIG_CPU_SUBTYPE_SH7750) := perf_event.o perf-$(CONFIG_CPU_SUBTYPE_SH7750S) := perf_event.o perf-$(CONFIG_CPU_SUBTYPE_SH7091) := perf_event.o +ifndef CONFIG_SH_DEVICE_TREE # CPU subtype setup obj-$(CONFIG_CPU_SUBTYPE_SH7750) += setup-sh7750.o obj-$(CONFIG_CPU_SUBTYPE_SH7750R) += setup-sh7750.o
@@ -29,5 +30,7 @@ ifndef CONFIG_CPU_SH4A clock-$(CONFIG_CPU_SH4) := clock-sh4.o endif +endif # CONFIG_SH_DEVICE_TREE + obj-y += $(clock-y) obj-$(CONFIG_PERF_EVENTS) += $(perf-y)
Signature · 1 line
2.39.2
Yoshinori Sato
maintainerPATCH RESEND v7 4/37 dt-bindings: interrupt-controller: Add header for Renesas SH3/4 INTC.
In reply to a message not in the archiveRenesas SH7751 Interrupt controller priority register define.
--- .../renesas,sh7751-intc.h | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) create mode 100644 include/dt-bindings/interrupt-controller/renesas,sh7751-intc.h
include/dt-bindings/interrupt-controller/renesas,sh7751-intc.h new file +19 -0
@@ -0,0 +1,19 @@ +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +* +* SH3/4 INTC IPR register offsets (Address / bits) +*/ + +#ifndef __DT_BINDINGS_RENESAS_SH7751_INTC +#define __DT_BINDINGS_RENESAS_SH7751_INTC + +#define IPRA 0 +#define IPRB 4 +#define IPRC 8 +#define IPRD 12 +#define INTPRI00 256 +#define IPR_B12 12 +#define IPR_B8 8 +#define IPR_B4 4 +#define IPR_B0 0 + +#endif
Signature · 1 line
2.39.2
Re: [RESEND v7 04/37] dt-bindings: interrupt-controller: Add header for Renesas SH3/4 INTC.
Quoted 3 lines · Yoshinori Sato
Renesas SH7751 Interrupt controller priority register define.
Signed-off-by Yoshinori Sato <[email protected]>
I got two 37-patchsets...
Anyway, this also did not improve. NAK.
This is a friendly reminder during the review process.
It seems my or other reviewer's previous comments were not fully addressed. Maybe the feedback got lost between the quotes, maybe you just forgot to apply it. Please go back to the previous discussion and either implement all requested changes or keep discussing them.
Thank you.
Best regards,
Krzysztof
Yoshinori Sato
maintainerPATCH RESEND v7 5/37 sh: GENERIC_IRQ_CHIP support for CONFIG_OF=y
In reply to a message not in the archiveRemove unused function prototype.
Add helper update_sr_imask. use for SH7751 irq driver. Add stub intc_finalize.
--- arch/sh/include/asm/io.h | 2 ++ arch/sh/include/asm/irq.h | 10 ++++++++-- arch/sh/kernel/cpu/Makefile | 5 +---- arch/sh/kernel/cpu/irq/imask.c | 17 +++++++++++++++++ include/linux/sh_intc.h | 7 ++++++- 5 files changed, 34 insertions(+), 7 deletions(-)
arch/sh/include/asm/io.h +2 -0
@@ -121,7 +121,9 @@ __BUILD_MEMORY_STRING(__raw_, q, u64)#define ioport_map ioport_map#define ioport_unmap ioport_unmap +#ifndef CONFIG_SH_DEVICE_TREE #define pci_iounmap pci_iounmap +#endif #define ioread8 ioread8#define ioread16 ioread16
arch/sh/include/asm/irq.h +8 -2
@@ -16,8 +16,8 @@/* * Simple Mask Register Support */ -extern void make_maskreg_irq (unsigned int irq); -extern unsigned short *irq_mask_register; + +void update_sr_imask (unsigned int irq,bool enable);/* * PINT IRQs
@@ -54,4 +54,10 @@ extern void irq_finish(unsigned int irq);#include <asm-generic/irq.h> +/* SH3/4 INTC stuff */ +/* IRL level 0 - 15 */ +#define NR_IRL 15 +/* IRL0 -> IRQ16 */ +#define IRL_BASE_IRQ 16 +#endif /* __ASM_SH_IRQ_H */
arch/sh/kernel/cpu/Makefile +1 -4
@@ -20,7 +20,4 @@ ifndef CONFIG_COMMON_CLK obj-y += clock.o obj-$(CONFIG_SH_CLK_CPG_LEGACY) += clock-cpg.o endif -ifndef CONFIG_GENERIC_IRQ_CHIP -obj-y += irq/ -endif -obj-y += init.o fpu.o pfc.o proc.o +obj-y += init.o fpu.o pfc.o proc.o irq/
arch/sh/kernel/cpu/irq/imask.c +17 -0
@@ -51,6 +51,7 @@ static inline void set_interrupt_registers(int ip) : "t"); } +#ifndef CONFIG_GENERIC_IRQ_CHIP static void mask_imask_irq (struct irq_data *data) {unsigned int irq = data->irq;
@@ -83,3 +84,19 @@ void make_imask_irq(unsigned int irq)irq_set_chip_and_handler_name (irq, &imask_irq_chip, handle_level_irq, "level"); } +#else +void update_sr_imask (unsigned int irq,bool enable) +{ +if (enable) { +set_bit (irq, imask_mask); + interrupt_priority =IMASK_PRIORITY - +find_first_bit (imask_mask,IMASK_PRIORITY ); + }else { +clear_bit (irq, imask_mask); +if (interrupt_priority <IMASK_PRIORITY - irq) + interrupt_priority =IMASK_PRIORITY - irq; + } +set_interrupt_registers (interrupt_priority); +} +EXPORT_SYMBOL (update_sr_imask); +#endif
include/linux/sh_intc.h +6 -1
@@ -139,8 +139,13 @@ struct intc_desc symbol __initdata = { \int register_intc_controller (struct intc_desc *desc);int intc_set_priority (unsigned int irq,unsigned int prio);int intc_irq_lookup (const char *chipname,intc_enum enum_id); +#ifndef CONFIG_SH_DEVICE_TREE void intc_finalize (void ); - +#else +static inline void intc_finalize (void ) +{ +} +#endif #ifdef CONFIG_INTC_USERIMASK int register_intc_userimask (unsigned long addr);#else
Signature · 1 line
2.39.2
Yoshinori Sato
maintainerPATCH RESEND v7 6/37 sh: kernel/setup Update DT support.
In reply to a message not in the archiveFix extrnal fdt initialize and bootargs.
--- arch/sh/Kconfig | 23 +++++++++++------------ arch/sh/include/asm/setup.h | 1 + arch/sh/kernel/setup.c | 36 +++++++++++++++++++++++------------- 3 files changed, 35 insertions(+), 25 deletions(-)
arch/sh/Kconfig +11 -12
@@ -708,17 +708,22 @@ config ROMIMAGE_MMCIF first part of the romImage which in turn loads the rest the kernel image to RAM using the MMCIF hardware block. +config CMDLINE + string "Kernel command line arguments string" + default "console=ttySC1,115200" + choice prompt "Kernel command line" - optional - default CMDLINE_OVERWRITE - depends on !OF || USE_BUILTIN_DTB + default CMDLINE_BOOTLOADER + +config CMDLINE_BOOTLOADER + bool "Use bootloader kernel arguments" help - Setting this option allows the kernel command line arguments - to be set. + Uses the command-line options passed by the boot loader. + If boot loader dosen't provide kernel argments, Use built-in argments. config CMDLINE_OVERWRITE - bool "Overwrite bootloader kernel arguments" + bool "Overwrite built-in kernel arguments" help Given string will overwrite any arguments passed in by a bootloader.
@@ -730,12 +735,6 @@ config CMDLINE_EXTEND by a bootloader. endchoice - -config CMDLINE - string "Kernel command line arguments string" - depends on CMDLINE_OVERWRITE || CMDLINE_EXTEND - default "console=ttySC1,115200" - endmenu menu "Bus options"
arch/sh/include/asm/setup.h +1 -0
@@ -21,5 +21,6 @@void sh_mv_setup (void );void check_for_initrd (void );void per_cpu_trap_init (void ); +void sh_fdt_init (phys_addr_t dt_phys);#endif /* _SH_SETUP_H */
arch/sh/kernel/setup.c +23 -13
@@ -30,6 +30,7 @@#include <linux/memblock.h> #include <linux/of.h> #include <linux/of_fdt.h> +#include <linux/libfdt.h> #include <linux/uaccess.h> #include <uapi/linux/mount.h> #include <asm/io.h>
@@ -269,8 +270,22 @@ void __ref sh_fdt_init(phys_addr_t dt_phys)void __init setup_arch (char **cmdline_p) { +#if defined(CONFIG_OF ) && defined(CONFIG_OF_EARLY_FLATTREE ) +if (IS_ENABLED (CONFIG_USE_BUILTIN_DTB )) { +/* Relocate Embedded DTB */ +unflatten_and_copy_device_tree (); + }else if (initial_boot_params) { +/* Reserve external DTB area */ +memblock_reserve (__pa (initial_boot_params), +fdt_totalsize (initial_boot_params)); +unflatten_device_tree (); + } +/* copy from /chosen/bootargs */ +strscpy (command_line, boot_command_line,COMMAND_LINE_SIZE ); +#endif enable_mmu (); +#ifndef CONFIG_OF ROOT_DEV =old_decode_dev (ORIG_ROOT_DEV ); printk(KERN_NOTICE "Boot params:\n"
@@ -299,14 +314,17 @@ void __init setup_arch(char **cmdline_p) bss_resource.start =virt_to_phys (__bss_start); bss_resource.end =virt_to_phys (__bss_stop)-1 ; -#ifdef CONFIG_CMDLINE_OVERWRITE -strscpy (command_line,CONFIG_CMDLINE ,sizeof (command_line)); -#else -strscpy (command_line,COMMAND_LINE ,sizeof (command_line)); +#endif +#if !defined(CONFIG_OF ) || defined(CONFIG_USE_BUILTIN_DTB ) +if (*COMMAND_LINE ) +strscpy (command_line,COMMAND_LINE ,sizeof (command_line)); +#endif +if (*command_line =='\0' ||IS_ENABLED (CONFIG_CMDLINE_OVERWRITE )) +/* Use built-in parameter */ +strscpy (command_line,CONFIG_CMDLINE ,sizeof (command_line));#ifdef CONFIG_CMDLINE_EXTEND strlcat (command_line," " ,sizeof (command_line));strlcat (command_line,CONFIG_CMDLINE ,sizeof (command_line)); -#endif #endif /* Save unparsed command line copy for /proc/cmdline */
@@ -322,14 +340,6 @@ void __init setup_arch(char **cmdline_p)/* Let earlyprintk output early console messages */ sh_early_platform_driver_probe ("earlyprintk" ,1 ,1 ); -#ifdef CONFIG_OF_EARLY_FLATTREE -#ifdef CONFIG_USE_BUILTIN_DTB -unflatten_and_copy_device_tree (); -#else -unflatten_device_tree (); -#endif -#endif -paging_init ();/* Perform the machine specific initialisation */
Signature · 1 line
2.39.2
Rob Herring
maintainerRe: [RESEND v7 06/37] sh: kernel/setup Update DT support.
Quoted 2 lines · Yoshinori Sato
Fix extrnal fdt initialize and bootargs.
What is the problem you are trying to solve?
And a typo.
Quoted 19 lines
Signed-off-by Yoshinori Sato <[email protected]>--- arch/sh/Kconfig | 23 +++++++++++------------ arch/sh/include/asm/setup.h | 1 + arch/sh/kernel/setup.c | 36 +++++++++++++++++++++++------------- 3 files changed, 35 insertions(+), 25 deletions(-)arch/sh/Kconfig +3
-0@@ -708,17 +708,22 @@ config ROMIMAGE_MMCIF first part of the romImage which in turn loads the rest the kernel image to RAM using the MMCIF hardware block. +config CMDLINE + string "Kernel command line arguments string" + default "console=ttySC1,115200"
arch/sh/Kconfig config ROMIMAGE_MMCIF · line 720
Quoted 10 lines
arch/sh/Kconfig +5
-3+ choice prompt "Kernel command line" - optional - default CMDLINE_OVERWRITE - depends on !OF || USE_BUILTIN_DTB + default CMDLINE_BOOTLOADER + +config CMDLINE_BOOTLOADER + bool "Use bootloader kernel arguments"
This should be the preferred, normal, default way. So why is it a user visible option?
arch/sh/Kconfig config ROMIMAGE_MMCIF · line 723
Quoted 5 lines
arch/sh/Kconfig +2
-2help - Setting this option allows the kernel command line arguments - to be set. + Uses the command-line options passed by the boot loader. + If boot loader dosen't provide kernel argments, Use built-in argments.
typos
bootloader in some spots, "boot loader" in others. Go with the former.
arch/sh/Kconfig config ROMIMAGE_MMCIF · line 726
Quoted 4 lines
arch/sh/Kconfig +1
-1config CMDLINE_OVERWRITE - bool "Overwrite bootloader kernel arguments" + bool "Overwrite built-in kernel arguments"
The original made more sense to me. The default should be to use bootloader args. Any built-in kernel command line should be prepend, append (extend), or overwrite/replace.
Rob
Yoshinori Sato
maintainerPATCH RESEND v7 7/37 sh: Fix COMMON_CLK support in CONFIG_OF=y.
In reply to a message not in the archiveInitialize the clock and timer using the COMMON_CLK procedure. sh's earlytimer mechanism doesn't work properly in OF, so timer initialization is delayed.
If CONFIG_OF=y, perform the general timer initialization procedure.
--- arch/sh/boards/of-generic.c | 28 ++++------------------------ arch/sh/kernel/time.c | 12 ++++++++++++ 2 files changed, 16 insertions(+), 24 deletions(-)
arch/sh/boards/of-generic.c +4 -24
@@ -8,6 +8,7 @@#include <linux/of.h> #include <linux/of_clk.h> #include <linux/of_fdt.h> +#include <linux/of_platform.h> #include <linux/clocksource.h> #include <linux/irqchip.h> #include <asm/machvec.h>
@@ -98,16 +99,7 @@ static void sh_of_smp_probe(void)#endif -static void noop (void ) -{ -} - -static int noopi (void ) -{ -return 0 ; -} - -static void __init sh_of_mem_reserve (void ) +static void __init sh_of_mem_init (void ) {early_init_fdt_reserve_self ();early_init_fdt_scan_reserved_mem ();
@@ -140,25 +132,13 @@ static void __init sh_of_init_irq(void)irqchip_init (); } -static int __init sh_of_clk_init (void ) -{ -#ifdef CONFIG_COMMON_CLK -/* Disabled pending move to COMMON_CLK framework. */ -pr_info ("SH generic board support: scanning for clk providers\n" ); -of_clk_init (NULL ); -#endif -return 0 ; -} - static struct sh_machine_vector __initmv sh_of_generic_mv = { .mv_setup = sh_of_setup, .mv_name ="devicetree" ,/* replaced by DT root's model */ .mv_irq_demux = sh_of_irq_demux, .mv_init_irq = sh_of_init_irq, - .mv_clk_init = sh_of_clk_init, - .mv_mode_pins = noopi, - .mv_mem_init = noop, - .mv_mem_reserve = sh_of_mem_reserve, + .mv_mode_pins = generic_mode_pins, + .mv_mem_init = sh_of_mem_init, };struct sh_clk_ops ;
arch/sh/kernel/time.c +12 -0
@@ -19,7 +19,9 @@#include <asm/clock.h> #include <asm/rtc.h> #include <asm/platform_early.h> +#include <linux/of_clk.h> +#ifndef CONFIG_SH_DEVICE_TREE static void __init sh_late_time_init (void ) {/*
@@ -43,3 +45,13 @@ void __init time_init(void) late_time_init = sh_late_time_init; } +#else +/* CONFIG_SH_DEVICE_TREE */ +void __init time_init (void ) +{ +pr_info ("SH generic board support: scanning for clk providers\n" ); + +of_clk_init (NULL ); +timer_probe (); +} +#endif
Signature · 1 line
2.39.2
Yoshinori Sato
maintainerPATCH RESEND v7 8/37 clocksource: sh_tmu: CLOCKSOURCE support.
In reply to a message not in the archiveAllows initialization as CLOCKSOURCE.
--- drivers/clocksource/sh_tmu.c | 198 ++++++++++++++++++++++++----------- 1 file changed, 134 insertions(+), 64 deletions(-)
drivers/clocksource/sh_tmu.c +134 -64
@@ -17,6 +17,8 @@#include <linux/irq.h> #include <linux/module.h> #include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_irq.h> #include <linux/platform_device.h> #include <linux/pm_domain.h> #include <linux/pm_runtime.h>
@@ -51,6 +53,7 @@ struct sh_tmu_channel {struct sh_tmu_device {struct platform_device *pdev; +struct device_node *np;void __iomem *mapbase;struct clk *clk;
@@ -65,6 +68,7 @@ struct sh_tmu_device {bool has_clockevent;bool has_clocksource; +const char *name; };#define TSTR -1/* shared register */
@@ -148,8 +152,8 @@ static int __sh_tmu_enable(struct sh_tmu_channel *ch)/* enable clock */ ret =clk_enable (ch->tmu->clk);if (ret) { -dev_err (&ch->tmu->pdev->dev,"ch%u: cannot enable clock\n" , - ch->index); +pr_err ("%s ch%u: cannot enable clock\n" , + ch->tmu->name, ch->index);return ret; }
@@ -174,9 +178,10 @@ static int sh_tmu_enable(struct sh_tmu_channel *ch)if (ch->enable_count++ >0 )return 0 ; -pm_runtime_get_sync (&ch->tmu->pdev->dev); -dev_pm_syscore_device (&ch->tmu->pdev->dev, true); - +if (ch->tmu->pdev) { +pm_runtime_get_sync (&ch->tmu->pdev->dev); +dev_pm_syscore_device (&ch->tmu->pdev->dev, true); + }return __sh_tmu_enable (ch); }
@@ -202,8 +207,10 @@ static void sh_tmu_disable(struct sh_tmu_channel *ch)__sh_tmu_disable (ch); -dev_pm_syscore_device (&ch->tmu->pdev->dev, false); -pm_runtime_put (&ch->tmu->pdev->dev); +if (ch->tmu->pdev) { +dev_pm_syscore_device (&ch->tmu->pdev->dev, false); +pm_runtime_put (&ch->tmu->pdev->dev); + } } static void sh_tmu_set_next(struct sh_tmu_channel *ch, unsigned long delta,
@@ -245,7 +252,7 @@ static irqreturn_t sh_tmu_interrupt(int irq, void *dev_id)return IRQ_HANDLED ; } -static struct sh_tmu_channel *cs_to_sh_tmu (struct clocksource *cs) +static inline struct sh_tmu_channel *cs_to_sh_tmu (struct clocksource *cs) { return container_of(cs, struct sh_tmu_channel, cs); }
@@ -292,7 +299,8 @@ static void sh_tmu_clocksource_suspend(struct clocksource *cs)if (--ch->enable_count ==0 ) {__sh_tmu_disable (ch); -dev_pm_genpd_suspend (&ch->tmu->pdev->dev); +if (ch->tmu->pdev) +dev_pm_genpd_suspend (&ch->tmu->pdev->dev); } }
@@ -304,7 +312,8 @@ static void sh_tmu_clocksource_resume(struct clocksource *cs)return ;if (ch->enable_count++ ==0 ) { -dev_pm_genpd_resume (&ch->tmu->pdev->dev); +if (ch->tmu->pdev) +dev_pm_genpd_resume (&ch->tmu->pdev->dev);__sh_tmu_enable (ch); } }
@@ -324,14 +333,14 @@ static int sh_tmu_register_clocksource(struct sh_tmu_channel *ch, cs->mask =CLOCKSOURCE_MASK (32 ); cs->flags =CLOCK_SOURCE_IS_CONTINUOUS ; -dev_info (&ch->tmu->pdev->dev,"ch%u: used as clock source\n" , - ch->index); +pr_info ("%s ch%u: used as clock source\n" , + ch->tmu->name, ch->index);clocksource_register_hz (cs, ch->tmu->rate);return 0 ; } -static struct sh_tmu_channel *ced_to_sh_tmu (struct clock_event_device *ced) +static inline struct sh_tmu_channel *ced_to_sh_tmu (struct clock_event_device *ced) { return container_of(ced, struct sh_tmu_channel, ced); }
@@ -364,8 +373,8 @@ static int sh_tmu_clock_event_set_state(struct clock_event_device *ced,if (clockevent_state_oneshot (ced) ||clockevent_state_periodic (ced))sh_tmu_disable (ch); -dev_info (&ch->tmu->pdev->dev,"ch%u: used for %s clock events\n" , - ch->index, periodic ?"periodic" :"oneshot" ); +pr_info ("%s ch%u: used for %s clock events\n" , + ch->tmu->name, ch->index, periodic ?"periodic" :"oneshot" );sh_tmu_clock_event_start (ch, periodic);return 0 ; }
@@ -417,20 +426,22 @@ static void sh_tmu_register_clockevent(struct sh_tmu_channel *ch, ced->set_state_shutdown = sh_tmu_clock_event_shutdown; ced->set_state_periodic = sh_tmu_clock_event_set_periodic; ced->set_state_oneshot = sh_tmu_clock_event_set_oneshot; - ced->suspend = sh_tmu_clock_event_suspend; - ced->resume = sh_tmu_clock_event_resume; +if (ch->tmu->pdev) { + ced->suspend = sh_tmu_clock_event_suspend; + ced->resume = sh_tmu_clock_event_resume; + } -dev_info (&ch->tmu->pdev->dev,"ch%u: used for clock events\n" , - ch->index); +pr_info ("%s ch%u: used for clock events\n" , + ch->tmu->name, ch->index);clockevents_config_and_register (ced, ch->tmu->rate,0x300 ,0xffffffff ); ret =request_irq (ch->irq, sh_tmu_interrupt,IRQF_TIMER |IRQF_IRQPOLL |IRQF_NOBALANCING , -dev_name (&ch->tmu->pdev->dev), ch); + ch->tmu->name, ch);if (ret) { -dev_err (&ch->tmu->pdev->dev,"ch%u: failed to request irq %d\n" , - ch->index, ch->irq); +pr_err ("%s ch%u: failed to request irq %d\n" , + ch->tmu->name, ch->index, ch->irq);return ; } }
@@ -465,28 +476,36 @@ static int sh_tmu_channel_setup(struct sh_tmu_channel *ch, unsigned int index,else ch->base = tmu->mapbase +8 + ch->index *12 ; - ch->irq =platform_get_irq (tmu->pdev, index); +if (tmu->pdev) + ch->irq =platform_get_irq (tmu->pdev, index); +if (tmu->np) + ch->irq =of_irq_get (tmu->np, index); +if (ch->irq <0 )return ch->irq; ch->cs_enabled = false; ch->enable_count =0 ; -return sh_tmu_register (ch,dev_name (&tmu->pdev->dev), - clockevent, clocksource); +return sh_tmu_register (ch, tmu->name, clockevent, clocksource); }static int sh_tmu_map_memory (struct sh_tmu_device *tmu) {struct resource *res; - res =platform_get_resource (tmu->pdev,IORESOURCE_MEM ,0 ); -if (!res) { -dev_err (&tmu->pdev->dev,"failed to get I/O memory\n" ); -return -ENXIO ; +if (tmu->pdev) { + res =platform_get_resource (tmu->pdev,IORESOURCE_MEM ,0 ); +if (!res) { +pr_err ("sh_tmu failed to get I/O memory\n" ); +return -ENXIO ; + } + + tmu->mapbase =ioremap (res->start,resource_size (res)); } +if (tmu->np) + tmu->mapbase =of_iomap (tmu->np,0 ); - tmu->mapbase =ioremap (res->start,resource_size (res));if (tmu->mapbase ==NULL )return -ENXIO ;
@@ -495,7 +514,12 @@ static int sh_tmu_map_memory(struct sh_tmu_device *tmu)static int sh_tmu_parse_dt (struct sh_tmu_device *tmu) { -struct device_node *np = tmu->pdev->dev.of_node; +struct device_node *np; + +if (tmu->pdev) + np = tmu->pdev->dev.of_node; +if (tmu->np) + np = tmu->np; tmu->model =SH_TMU ; tmu->num_channels =3 ;
@@ -503,45 +527,19 @@ static int sh_tmu_parse_dt(struct sh_tmu_device *tmu)of_property_read_u32 (np,"#renesas,channels" , &tmu->num_channels);if (tmu->num_channels !=2 && tmu->num_channels !=3 ) { -dev_err (&tmu->pdev->dev,"invalid number of channels %u\n" , - tmu->num_channels); +pr_err ("%s: invalid number of channels %u\n" , + tmu->name, tmu->num_channels);return -EINVAL ; }return 0 ; } -static int sh_tmu_setup (struct sh_tmu_device *tmu,struct platform_device *pdev) +static int sh_tmu_setup (struct sh_tmu_device *tmu) {unsigned int i;int ret; - tmu->pdev = pdev; - -raw_spin_lock_init (&tmu->lock); - -if (IS_ENABLED (CONFIG_OF ) && pdev->dev.of_node) { - ret =sh_tmu_parse_dt (tmu); -if (ret <0 ) -return ret; - }else if (pdev->dev.platform_data) { -const struct platform_device_id *id = pdev->id_entry; -struct sh_timer_config *cfg = pdev->dev.platform_data; - - tmu->model = id->driver_data; - tmu->num_channels =hweight8 (cfg->channels_mask); - }else { -dev_err (&tmu->pdev->dev,"missing platform data\n" ); -return -ENXIO ; - } - -/* Get hold of clock. */ - tmu->clk =clk_get (&tmu->pdev->dev,"fck" ); -if (IS_ERR (tmu->clk)) { -dev_err (&tmu->pdev->dev,"cannot get clock\n" ); -return PTR_ERR (tmu->clk); - } - ret =clk_prepare (tmu->clk);if (ret <0 ) goto err_clk_put;
@@ -557,7 +555,7 @@ static int sh_tmu_setup(struct sh_tmu_device *tmu, struct platform_device *pdev)/* Map the memory resource. */ ret =sh_tmu_map_memory (tmu);if (ret <0 ) { -dev_err (&tmu->pdev->dev,"failed to remap I/O memory\n" ); +pr_err ("%s: failed to remap I/O memory\n" , tmu->name); goto err_clk_unprepare; }
@@ -580,8 +578,6 @@ static int sh_tmu_setup(struct sh_tmu_device *tmu, struct platform_device *pdev) goto err_unmap; } -platform_set_drvdata (pdev, tmu); -return 0 ; err_unmap:
@@ -594,6 +590,39 @@ static int sh_tmu_setup(struct sh_tmu_device *tmu, struct platform_device *pdev)return ret; } +static int sh_tmu_setup_pdev (struct sh_tmu_device *tmu,struct platform_device *pdev) +{ +int ret; + + tmu->pdev = pdev; + +raw_spin_lock_init (&tmu->lock); + +if (IS_ENABLED (CONFIG_OF ) && pdev->dev.of_node) { + ret =sh_tmu_parse_dt (tmu); +if (ret <0 ) +return ret; + }else if (pdev->dev.platform_data) { +const struct platform_device_id *id = pdev->id_entry; +struct sh_timer_config *cfg = pdev->dev.platform_data; + + tmu->model = id->driver_data; + tmu->num_channels =hweight8 (cfg->channels_mask); + }else { +dev_err (&tmu->pdev->dev,"missing platform data\n" ); +return -ENXIO ; + } + + tmu->name =dev_name (&pdev->dev); + tmu->clk =clk_get (&tmu->pdev->dev,"fck" ); +if (IS_ERR (tmu->clk)) { +dev_err (&tmu->pdev->dev,"cannot get clock\n" ); +return PTR_ERR (tmu->clk); + } + +return sh_tmu_setup (tmu); +} +static int sh_tmu_probe (struct platform_device *pdev) {struct sh_tmu_device *tmu =platform_get_drvdata (pdev);
@@ -613,12 +642,13 @@ static int sh_tmu_probe(struct platform_device *pdev)if (tmu ==NULL )return -ENOMEM ; - ret =sh_tmu_setup (tmu, pdev); + ret =sh_tmu_setup_pdev (tmu, pdev);if (ret) {kfree (tmu);pm_runtime_idle (&pdev->dev);return ret; } +platform_set_drvdata (pdev, tmu);if (is_sh_early_platform_device (pdev))return 0 ;
@@ -632,6 +662,45 @@ static int sh_tmu_probe(struct platform_device *pdev)return 0 ; } +static int sh_tmu_setup_of (struct sh_tmu_device *tmu,struct device_node *np) +{ +int ret; + + tmu->np = np; +raw_spin_lock_init (&tmu->lock); + + ret =sh_tmu_parse_dt (tmu); +if (ret <0 ) +return ret; + + tmu->clk =of_clk_get (np,0 ); + tmu->name =of_node_full_name (np); + +if (IS_ERR (tmu->clk)) { +pr_err ("%pOF: cannot get clock\n" , np); +return PTR_ERR (tmu->clk); + } + +return sh_tmu_setup (tmu); +} + +static int __init sh_tmu_of_register (struct device_node *np) +{ +struct sh_tmu_device *tmu; +int ret; + + tmu =kzalloc (sizeof (*tmu),GFP_KERNEL ); +if (tmu ==NULL ) +return -ENOMEM ; + + ret =sh_tmu_setup_of (tmu, np); +if (ret) { +kfree (tmu); +pr_warn ("%pOF: Timer register failed (%d)" , np, ret); + } +return ret; +} +static const struct platform_device_id sh_tmu_id_table[] = { {"sh-tmu" ,SH_TMU }, {"sh-tmu-sh3" ,SH_TMU_SH3 },
@@ -665,6 +734,7 @@ static void __exit sh_tmu_exit(void)platform_driver_unregister (&sh_tmu_device_driver); } +TIMER_OF_DECLARE (sh_tmu,"renesas,tmu" , sh_tmu_of_register);#ifdef CONFIG_SUPERH sh_early_platform_init ("earlytimer" , &sh_tmu_device_driver);#endif
Signature · 1 line
2.39.2
Re: [RESEND v7 08/37] clocksource: sh_tmu: CLOCKSOURCE support.
Hi Sato-san,
Quoted 3 lines · Yoshinori Sato
Allows initialization as CLOCKSOURCE.
Signed-off-by Yoshinori Sato <[email protected]>
Thanks for your patch!
drivers/clocksource/sh_tmu.c static int sh_tmu_map_memory(struct sh_tmu_device *tmu) · line 517
Quoted 9 lines
drivers/clocksource/sh_tmu.c +1
-1@@ -495,7 +514,12 @@ static int sh_tmu_map_memory(struct sh_tmu_device *tmu)static int sh_tmu_parse_dt (struct sh_tmu_device *tmu) { -struct device_node *np = tmu->pdev->dev.of_node; +struct device_node *np;
Technically, np might be used uninitialized.
drivers/clocksource/sh_tmu.c static int sh_tmu_map_memory(struct sh_tmu_device *tmu) · line 520
Quoted 3 lines
drivers/clocksource/sh_tmu.c +3
-0+ +if (tmu->pdev) + np = tmu->pdev->dev.of_node;
If you would set up tmu->np in sh_tmu_setup_pdev()...
drivers/clocksource/sh_tmu.c static int sh_tmu_map_memory(struct sh_tmu_device *tmu) · line 522
Quoted 2 lines
drivers/clocksource/sh_tmu.c +2
-0+if (tmu->np) + np = tmu->np;
... you could just assign np = tmu->np unconditionally.
drivers/clocksource/sh_tmu.c static void __exit sh_tmu_exit(void) · line 737
Quoted 9 lines
drivers/clocksource/sh_tmu.c +1
-0tmu->model =SH_TMU ; tmu->num_channels =3 ;@@ -665,6 +734,7 @@ static void __exit sh_tmu_exit(void)platform_driver_unregister (&sh_tmu_device_driver); } +TIMER_OF_DECLARE (sh_tmu,"renesas,tmu" , sh_tmu_of_register);
As there are now two entry points, the device is actually probed twice:
once from TIMER_OF_DECLARE/sh_tmu_of_register(), and a second time from platform_driver/sh_tmu_probe().
E.g. on Armadillo-800-EVA with R-Mobile A1 (booting Linux on ARM (not SH), and using TMU as the main clock source):
timer@fff80000 ch0: used for clock events timer@fff80000 ch0: used for periodic clock events timer@fff80000 ch1: used as clock source
clocksource: timer@fff80000: mask: 0xffffffff max_cycles:0xffffffff, max_idle_ns: 154445288668 ns
...
fff80000.timer ch0: used for clock events
genirq: Flags mismatch irq 16. 00015a04 (fff80000.timer) vs.00015a04 (timer@fff80000)
fff80000.timer ch0: failed to request irq 16 fff80000.timer ch1: used as clock source
clocksource: fff80000.timer: mask: 0xffffffff max_cycles:0xffffffff, max_idle_ns: 154445288668 ns
After this, the timer seems to be stuck, and the boot is blocked.
On Marzen with R-Car H1 (booting Linux on ARM (not SH), and using arm_global_timer as the main clock source), I also see the double timer probe, but no such lock-up. I expect you to see the double timer probe on SH775x, too?
The double probe can be fixed by adding a call to of_node_set_flag(np, OF_POPULATED) at the end of sh_tmu_of_register() in case of success, cfr. [1].
I haven't found the cause of the stuck timer on R-Mobile A1 yet; both the TMU clock and the A4R power domain seem to be activated...
drivers/clocksource/sh_tmu.c static void __exit sh_tmu_exit(void) · line 740
Quoted 3 lines
drivers/clocksource/sh_tmu.c +0
-0#ifdef CONFIG_SUPERH sh_early_platform_init ("earlytimer" , &sh_tmu_device_driver);#endif
[1] "[PATCH] clocksource/drivers/renesas-ostm: Avoid reprobe after successful early probe"
https://lore.kernel.org/all/bd027379713cbaafa21ffe9e848ebb7f475ca0e7.1710930542.git.geert+renesas@glider.be/
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]
In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
Yoshinori Sato
maintainerPATCH RESEND v7 9/37 dt-binding: Add compatible SH7750 SoC
In reply to a message not in the archive--- Documentation/devicetree/bindings/timer/renesas,tmu.yaml | 2 ++ 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/timer/renesas,tmu.yaml +2 -0
@@ -39,6 +39,7 @@ properties: - renesas,tmu-r8a779a0 # R-Car V3U - renesas,tmu-r8a779f0 # R-Car S4-8 - renesas,tmu-r8a779g0 # R-Car V4H + - renesas,tmu-sh7750 # SH7750 - const: renesas,tmu reg:
@@ -96,6 +97,7 @@ if: - renesas,tmu-r8a7740 - renesas,tmu-r8a7778 - renesas,tmu-r8a7779 + - renesas,tmu-sh7750 then: required: - resets
Signature · 1 line
2.39.2
Re: [RESEND v7 09/37] dt-binding: Add compatible SH7750 SoC
Quoted 1 line · Yoshinori Sato
Signed-off-by Yoshinori Sato <[email protected]>
Gr{oetje,eeting}s,
Geert
Signature · 5 lines
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected] In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds
Re: [RESEND v7 09/37] dt-binding: Add compatible SH7750 SoC
In reply to Yoshinori SatoQuoted 5 lines · Yoshinori Sato
Signed-off-by Yoshinori Sato <[email protected]>--- Documentation/devicetree/bindings/timer/renesas,tmu.yaml | 2 ++ 1 file changed, 2 insertions(+)
Yoshinori Sato
maintainerPATCH RESEND v7 10/37 sh: Common PCI Framework driver support.
In reply to a message not in the archiveAdd New OF based PCI Host driver.
This driver conflicts some point in legacy PCI driver. To resolve the conflict, I made some changes to the legacy driver.
--- arch/sh/include/asm/io.h | 6 ++++++ arch/sh/include/asm/pci.h | 4 ++++ arch/sh/kernel/iomap.c | 18 ++++++++++++++++++ 3 files changed, 28 insertions(+)
arch/sh/include/asm/io.h +6 -0
@@ -20,6 +20,7 @@#include <asm/page.h> #include <linux/pgtable.h> #include <asm-generic/iomap.h> +#include <linux/ioport.h> #define __IO_PREFIX generic#include <asm/io_generic.h>
@@ -310,4 +311,9 @@ unsigned long long poke_real_address_q(unsigned long long addr,int valid_phys_addr_range (phys_addr_t addr,size_t size);int valid_mmap_phys_addr_range (unsigned long pfn,size_t size); +#if defined(CONFIG_PCI ) && !defined(CONFIG_GENERIC_IOMAP ) +#define pci_remap_iospace pci_remap_iospace +int pci_remap_iospace (const struct resource *res,phys_addr_t phys_addr); +#endif +#endif /* __ASM_SH_IO_H */
arch/sh/include/asm/pci.h +4 -0
@@ -2,6 +2,7 @@#ifndef __ASM_SH_PCI_H#define __ASM_SH_PCI_H +#ifndef CONFIG_SH_DEVICE_TREE /* Can be used to override the logic in pci_scan_bus for skipping already-configured bus numbers - to be used for buggy BIOSes or architectures with incomplete PCI setup by the loader */
@@ -88,4 +89,7 @@ static inline int pci_proc_domain(struct pci_bus *bus)return hose->need_domain_info; } +#else /* CONFIG_SH_DEVICE_TREE */ +#include <asm-generic/pci.h> +#endif #endif /* __ASM_SH_PCI_H */
arch/sh/kernel/iomap.c +18 -0
@@ -160,3 +160,21 @@ void iowrite32_rep(void __iomem *addr, const void *src, unsigned long count)mmio_outsl (addr, src, count); }EXPORT_SYMBOL (iowrite32_rep); + +#if defined(pci_remap_iospace) +int pci_remap_iospace (const struct resource *res,phys_addr_t phys_addr) +{ +unsigned long vaddr = res->start; + +if (!(res->flags &IORESOURCE_IO )) +return -EINVAL ; + +if (res->end >IO_SPACE_LIMIT ) +return -EINVAL ; + +__set_io_port_base (phys_addr); +return vmap_page_range (vaddr, vaddr +resource_size (res), phys_addr, +pgprot_device (PAGE_KERNEL )); +} +EXPORT_SYMBOL (pci_remap_iospace); +#endif
Signature · 1 line
2.39.2
Yoshinori Sato
maintainerPATCH RESEND v7 11/37 pci: pci-sh7751: Add SH7751 PCI driver
In reply to a message not in the archiveRenesas SH7751 CPU Internal PCI Controller driver.
--- drivers/pci/controller/Kconfig | 9 + drivers/pci/controller/Makefile | 1 + drivers/pci/controller/pci-sh7751.c | 342 ++++++++++++++++++++++++++++ 3 files changed, 352 insertions(+) create mode 100644 drivers/pci/controller/pci-sh7751.c
drivers/pci/controller/Kconfig +9 -0
@@ -353,6 +353,15 @@ config PCIE_XILINX_CPM Say 'Y' here if you want kernel support for the Xilinx Versal CPM host bridge. +config PCI_SH7751 + bool "Renesas SH7751 PCI controller" + depends on OF + depends on CPU_SUBTYPE_SH7751 || CPU_SUBTYPE_SH7751R || COMPILE_TEST + select PCI_HOST_COMMON + help + Say 'Y' here if you want kernel to support the Renesas SH7751 PCI + Host Bridge driver. + source "drivers/pci/controller/cadence/Kconfig" source "drivers/pci/controller/dwc/Kconfig" source "drivers/pci/controller/mobiveil/Kconfig"
drivers/pci/controller/Makefile +1 -0
@@ -40,6 +40,7 @@ obj-$(CONFIG_PCI_LOONGSON) += pci-loongson.o obj-$(CONFIG_PCIE_HISI_ERR) += pcie-hisi-error.o obj-$(CONFIG_PCIE_APPLE) += pcie-apple.o obj-$(CONFIG_PCIE_MT7621) += pcie-mt7621.o +obj-$(CONFIG_PCI_SH7751) += pci-sh7751.o # pcie-hisi.o quirks are needed even without CONFIG_PCIE_DW obj-y += dwc/
drivers/pci/controller/pci-sh7751.c new file +342 -0
342 lines not on this page · raw message
Signature · 1 line
2.39.2
Yoshinori Sato
maintainerPATCH RESEND v7 12/37 dt-bindings: pci: pci-sh7751: Add SH7751 PCI
In reply to a message not in the archiveRenesas SH7751 PCI Controller json-schema.
--- .../bindings/pci/renesas,sh7751-pci.yaml | 89 +++++++++++++++++++ 1 file changed, 89 insertions(+) create mode 100644 Documentation/devicetree/bindings/pci/renesas,sh7751-pci.yaml
Documentation/devicetree/bindings/pci/renesas,sh7751-pci.yaml new file +89 -0
@@ -0,0 +1,89 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pci/renesas,sh7751-pci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas SH7751 PCI Host controller + +maintainers: + - Yoshinori Sato <[email protected]> + +allOf: + - $ref: /schemas/pci/pci-bus.yaml# + +properties: + compatible: + const: renesas,sh7751-pci + + reg: + minItems: 2 + maxItems: 2 + + reg-names: + items: + - const: PCI Controller + - const: Bus State Controller + + "#interrupt-cells": + const: 1 + + "#address-cells": + const: 3 + + "#size-cells": + const: 2 + + ranges: true + + dma-ranges: true + + interrupt-controller: true + + renesas,bus-arbit-round-robin: + $ref: /schemas/types.yaml#/definitions/flag + description: | + Set DMA bus arbitration to round robin. + +required: + - compatible + - reg + - "#interrupt-cells" + - "#address-cells" + - "#size-cells" + - ranges + - interrupt-map + - interrupt-map-mask + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + pci@fe200000 { + compatible = "renesas,sh7751-pci"; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupt-controller; + device_type = "pci"; + bus-range = <0 0>; + ranges = <0x02000000 0 0xfd000000 0xfd000000 0 0x01000000>, + <0x01000000 0 0x00000000 0xfe240000 0 0x00040000>; + dma-ranges = <0x02000000 0 0xc000000 0x0c000000 0 0x04000000>; + reg = <0xfe200000 0x0400>, + <0xff800000 0x0100>; + interrupt-map = <0x0000 0 0 1 &julianintc 5 IRQ_TYPE_LEVEL_LOW>, + <0x0000 0 0 2 &julianintc 6 IRQ_TYPE_LEVEL_LOW>, + <0x0000 0 0 3 &julianintc 7 IRQ_TYPE_LEVEL_LOW>, + <0x0000 0 0 4 &julianintc 8 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 1 &julianintc 6 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 2 &julianintc 7 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 3 &julianintc 8 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 4 &julianintc 5 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 1 &julianintc 7 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 2 &julianintc 8 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 3 &julianintc 5 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 4 &julianintc 6 IRQ_TYPE_LEVEL_LOW>; + interrupt-map-mask = <0x1800 0 0 7>; + };
Signature · 1 line
2.39.2
Rob Herring
maintainerRe: [RESEND v7 12/37] dt-bindings: pci: pci-sh7751: Add SH7751 PCI
Quoted 44 lines · Yoshinori Sato
Renesas SH7751 PCI Controller json-schema.
Signed-off-by Yoshinori Sato <[email protected]>--- .../bindings/pci/renesas,sh7751-pci.yaml | 89 +++++++++++++++++++ 1 file changed, 89 insertions(+) create mode 100644 Documentation/devicetree/bindings/pci/renesas,sh7751-pci.yamlDocumentation/devicetree/bindings/pci/renesas,sh7751-pci.yaml new file +29
-0@@ -0,0 +1,89 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pci/renesas,sh7751-pci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas SH7751 PCI Host controller + +maintainers: + - Yoshinori Sato <[email protected]> + +allOf: + - $ref: /schemas/pci/pci-bus.yaml# + +properties: + compatible: + const: renesas,sh7751-pci + + reg: + minItems: 2 + maxItems: 2 + + reg-names: + items: + - const: PCI Controller + - const: Bus State Controller + + "#interrupt-cells": + const: 1
Documentation/devicetree/bindings/pci/renesas,sh7751-pci.yaml line 39
Quoted 10 lines
Documentation/devicetree/bindings/pci/renesas,sh7751-pci.yaml new file +10
-0+ + "#address-cells": + const: 3 + + "#size-cells": + const: 2 + + ranges: true + + dma-ranges: true
All 5 of these are defined in pci-bus-common.yaml, so you can drop them.
Documentation/devicetree/bindings/pci/renesas,sh7751-pci.yaml line 45
Quoted 6 lines
Documentation/devicetree/bindings/pci/renesas,sh7751-pci.yaml new file +6
-0+ + interrupt-controller: true + + renesas,bus-arbit-round-robin: + $ref: /schemas/types.yaml#/definitions/flag + description: |
Don't need '|'.
Documentation/devicetree/bindings/pci/renesas,sh7751-pci.yaml line 54
Quoted 10 lines
Documentation/devicetree/bindings/pci/renesas,sh7751-pci.yaml new file +9
-0+ Set DMA bus arbitration to round robin. + +required: + - compatible + - reg + - "#interrupt-cells" + - "#address-cells" + - "#size-cells" + - ranges
These 3 are already required, so drop.
Quoted 38 lines
Documentation/devicetree/bindings/pci/renesas,sh7751-pci.yaml new file +35
-0+ - interrupt-map + - interrupt-map-mask + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + pci@fe200000 { + compatible = "renesas,sh7751-pci"; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupt-controller; + device_type = "pci"; + bus-range = <0 0>; + ranges = <0x02000000 0 0xfd000000 0xfd000000 0 0x01000000>, + <0x01000000 0 0x00000000 0xfe240000 0 0x00040000>; + dma-ranges = <0x02000000 0 0xc000000 0x0c000000 0 0x04000000>; + reg = <0xfe200000 0x0400>, + <0xff800000 0x0100>; + interrupt-map = <0x0000 0 0 1 &julianintc 5 IRQ_TYPE_LEVEL_LOW>, + <0x0000 0 0 2 &julianintc 6 IRQ_TYPE_LEVEL_LOW>, + <0x0000 0 0 3 &julianintc 7 IRQ_TYPE_LEVEL_LOW>, + <0x0000 0 0 4 &julianintc 8 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 1 &julianintc 6 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 2 &julianintc 7 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 3 &julianintc 8 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 4 &julianintc 5 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 1 &julianintc 7 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 2 &julianintc 8 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 3 &julianintc 5 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 4 &julianintc 6 IRQ_TYPE_LEVEL_LOW>; + interrupt-map-mask = <0x1800 0 0 7>; + };Signature · 1 line
2.39.2
Yoshinori Sato
maintainerPATCH RESEND v7 13/37 dt-bindings: clock: sh7750-cpg: Add renesas,sh7750-cpg header.
In reply to a message not in the archiveSH7750 CPG Clock output define.
--- .../bindings/clock/renesas,sh7750-cpg.yaml | 105 ++++++++++++++++++ include/dt-bindings/clock/sh7750-cpg.h | 26 +++++ 2 files changed, 131 insertions(+) create mode 100644 Documentation/devicetree/bindings/clock/renesas,sh7750-cpg.yaml create mode 100644 include/dt-bindings/clock/sh7750-cpg.h
Documentation/devicetree/bindings/clock/renesas,sh7750-cpg.yaml new file +105 -0
@@ -0,0 +1,105 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/renesas,sh7750-cpg.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas SH7750/7751 Clock Pulse Generator (CPG) + +maintainers: + - Yoshinori Sato <[email protected]> + +description: + The Clock Pulse Generator (CPG) generates core clocks for the SoC. It + includes PLLs, and variable ratio dividers. + + The CPG may also provide a Clock Domain for SoC devices, in combination with + the CPG Module Stop (MSTP) Clocks. + +properties: + compatible: + enum: + - renesas,sh7750-cpg # SH7750 + - renesas,sh7750s-cpg # SH775S + - renesas,sh7750r-cpg # SH7750R + - renesas,sh7751-cpg # SH7751 + - renesas,sh7751r-cpg # SH7751R + + reg: true + + reg-names: true + + clocks: + maxItems: 1 + + clock-names: + const: extal + + '#clock-cells': + const: 1 + + renesas,mode: + description: Board-specific settings of the MD[0-2] pins on SoC + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 6 + + '#power-domain-cells': + const: 0 + +required: + - compatible + - reg + - reg-names + - clocks + - clock-names + - '#clock-cells' + +allOf: + - if: + properties: + compatible: + contains: + enum: + - renesas,sh7750-cpg + - renesas,sh7750s-cpg + then: + properties: + reg: + maxItems: 1 + reg-names: + items: + - const: FRQCR + + - if: + properties: + compatible: + contains: + enum: + - renesas,sh7750r-cpg + - renesas,sh7751-cpg + - renesas,sh7751r-cpg + then: + properties: + reg: + maxItems: 2 + reg-names: + items: + - const: FRQCR + - const: CLKSTP00 + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/sh7750-cpg.h> + cpg: clock-controller@ffc00000 { + #clock-cells = <1>; + #power-domain-cells = <0>; + compatible = "renesas,sh7751r-cpg"; + clocks = <&extal>; + clock-names = "extal"; + reg = <0xffc00000 20>, <0xfe0a0000 16>; + reg-names = "FRQCR", "CLKSTP00"; + renesas,mode = <0>; + };
include/dt-bindings/clock/sh7750-cpg.h new file +26 -0
@@ -0,0 +1,26 @@ +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +* +* Copyright 2023 Yoshinori Sato +*/ + +#ifndef __DT_BINDINGS_CLOCK_SH7750_H__ +#define __DT_BINDINGS_CLOCK_SH7750_H__ + +#define SH7750_CPG_PLLOUT 0 + +#define SH7750_CPG_PCK 1 +#define SH7750_CPG_BCK 2 +#define SH7750_CPG_ICK 3 + +#define SH7750_MSTP_SCI 4 +#define SH7750_MSTP_RTC 5 +#define SH7750_MSTP_TMU012 6 +#define SH7750_MSTP_SCIF 7 +#define SH7750_MSTP_DMAC 8 +#define SH7750_MSTP_UBC 9 +#define SH7750_MSTP_SQ 10 +#define SH7750_CSTP_INTC 11 +#define SH7750_CSTP_TMU34 12 +#define SH7750_CSTP_PCIC 13 + +#endif
Signature · 1 line
2.39.2
Re: [RESEND v7 13/37] dt-bindings: clock: sh7750-cpg: Add renesas,sh7750-cpg header.
Hi Sato-san,
Thanks for the update!
Quoted 2 lines · Yoshinori Sato
SH7750 CPG Clock output define.
(from my comments on v6) Please improve the patch description.
Documentation/devicetree/bindings/clock/renesas,sh7750-cpg.yaml
Quoted 5 lines
Signed-off-by Yoshinori Sato <[email protected]>index 000000000000..04c10b0834ee
Documentation/devicetree/bindings/clock/renesas,sh7750-cpg.yaml new file +0
-0
The actual bindings LGTM.
Documentation/devicetree/bindings/clock/renesas,sh7750-cpg.yaml line 105
Quoted 13 lines
Documentation/devicetree/bindings/clock/renesas,sh7750-cpg.yaml new file +13
-0+examples: + - | + #include <dt-bindings/clock/sh7750-cpg.h> + cpg: clock-controller@ffc00000 { + #clock-cells = <1>; + #power-domain-cells = <0>; + compatible = "renesas,sh7751r-cpg"; + clocks = <&extal>; + clock-names = "extal"; + reg = <0xffc00000 20>, <0xfe0a0000 16>; + reg-names = "FRQCR", "CLKSTP00"; + renesas,mode = <0>; + };
Please read
https://docs.kernel.org/devicetree/bindings/dts-coding-style.html#order-of-properties-in-device-node
Gr{oetje,eeting}s,
Geert
Signature · 5 lines
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected] In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds
Rob Herring
maintainerRe: [RESEND v7 13/37] dt-bindings: clock: sh7750-cpg: Add renesas,sh7750-cpg header.
In reply to Yoshinori SatoQuoted 1 line · Yoshinori Sato
SH7750 CPG Clock output define.
This and the subject don't match what the patch does.
Quoted 90 lines
Signed-off-by Yoshinori Sato <[email protected]>--- .../bindings/clock/renesas,sh7750-cpg.yaml | 105 ++++++++++++++++++ include/dt-bindings/clock/sh7750-cpg.h | 26 +++++ 2 files changed, 131 insertions(+) create mode 100644 Documentation/devicetree/bindings/clock/renesas,sh7750-cpg.yaml create mode 100644 include/dt-bindings/clock/sh7750-cpg.hDocumentation/devicetree/bindings/clock/renesas,sh7750-cpg.yaml new file +75
-0@@ -0,0 +1,105 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/renesas,sh7750-cpg.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas SH7750/7751 Clock Pulse Generator (CPG) + +maintainers: + - Yoshinori Sato <[email protected]> + +description: + The Clock Pulse Generator (CPG) generates core clocks for the SoC. It + includes PLLs, and variable ratio dividers. + + The CPG may also provide a Clock Domain for SoC devices, in combination with + the CPG Module Stop (MSTP) Clocks. + +properties: + compatible: + enum: + - renesas,sh7750-cpg # SH7750 + - renesas,sh7750s-cpg # SH775S + - renesas,sh7750r-cpg # SH7750R + - renesas,sh7751-cpg # SH7751 + - renesas,sh7751r-cpg # SH7751R + + reg: true + + reg-names: true + + clocks: + maxItems: 1 + + clock-names: + const: extal + + '#clock-cells': + const: 1 + + renesas,mode: + description: Board-specific settings of the MD[0-2] pins on SoC + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 6 + + '#power-domain-cells': + const: 0 + +required: + - compatible + - reg + - reg-names + - clocks + - clock-names + - '#clock-cells' + +allOf: + - if: + properties: + compatible: + contains: + enum: + - renesas,sh7750-cpg + - renesas,sh7750s-cpg + then: + properties: + reg: + maxItems: 1 + reg-names: + items: + - const: FRQCR + + - if: + properties:
Documentation/devicetree/bindings/clock/renesas,sh7750-cpg.yaml line 85
Quoted 10 lines
Documentation/devicetree/bindings/clock/renesas,sh7750-cpg.yaml new file +10
-0+ compatible: + contains: + enum: + - renesas,sh7750r-cpg + - renesas,sh7751-cpg + - renesas,sh7751r-cpg + then: + properties: + reg: + maxItems: 2
minItems: 2 (instead)
Documentation/devicetree/bindings/clock/renesas,sh7750-cpg.yaml line 89
Quoted 4 lines
Documentation/devicetree/bindings/clock/renesas,sh7750-cpg.yaml new file +4
-0+ reg-names: + items: + - const: FRQCR + - const: CLKSTP00
Move this to the top-level and add 'minItems: 1'. Then above you just need 'maxItems: 1' and here 'minItems: 2'.
Quoted 51 lines
Documentation/devicetree/bindings/clock/renesas,sh7750-cpg.yaml new file +16
-0+ +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/sh7750-cpg.h> + cpg: clock-controller@ffc00000 { + #clock-cells = <1>; + #power-domain-cells = <0>; + compatible = "renesas,sh7751r-cpg"; + clocks = <&extal>; + clock-names = "extal"; + reg = <0xffc00000 20>, <0xfe0a0000 16>; + reg-names = "FRQCR", "CLKSTP00"; + renesas,mode = <0>; + };include/dt-bindings/clock/sh7750-cpg.h new file +26
-0@@ -0,0 +1,26 @@ +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +* +* Copyright 2023 Yoshinori Sato +*/ + +#ifndef __DT_BINDINGS_CLOCK_SH7750_H__ +#define __DT_BINDINGS_CLOCK_SH7750_H__ + +#define SH7750_CPG_PLLOUT 0 + +#define SH7750_CPG_PCK 1 +#define SH7750_CPG_BCK 2 +#define SH7750_CPG_ICK 3 + +#define SH7750_MSTP_SCI 4 +#define SH7750_MSTP_RTC 5 +#define SH7750_MSTP_TMU012 6 +#define SH7750_MSTP_SCIF 7 +#define SH7750_MSTP_DMAC 8 +#define SH7750_MSTP_UBC 9 +#define SH7750_MSTP_SQ 10 +#define SH7750_CSTP_INTC 11 +#define SH7750_CSTP_TMU34 12 +#define SH7750_CSTP_PCIC 13 + +#endif Signature · 1 line
2.39.2
Yoshinori Sato
maintainerPATCH RESEND v7 14/37 clk: Compatible with narrow registers
In reply to a message not in the archivedivider and gate only support 32-bit registers.
Older hardware uses narrower registers, so I want to be able to handle 8-bit and 16-bit wide registers.
Seven clk_divider flags are used, and if I add flags for 8bit access and 16bit access, 8bit will not be enough, so I expanded it to u16.
--- drivers/clk/clk-divider.c | 56 +++++++++++++++++++++----------- drivers/clk/clk-gate.c | 62 ++++++++++++++++++++++++++++-------- include/linux/clk-provider.h | 22 ++++++++++--- 3 files changed, 103 insertions(+), 37 deletions(-)
drivers/clk/clk-divider.c +37 -19
@@ -26,20 +26,38 @@* parent - fixed parent. No clk_set_parent support */ -static inline u32 clk_div_readl (struct clk_divider *divider) -{ -if (divider->flags &CLK_DIVIDER_BIG_ENDIAN ) -return ioread32be (divider->reg); - -return readl (divider->reg); +static inline u32 clk_div_read (struct clk_divider *divider) +{ +if (divider->flags &CLK_DIVIDER_REG_8BIT ) +return readb (divider->reg); +else if (divider->flags &CLK_DIVIDER_REG_16BIT ) { +if (divider->flags &CLK_DIVIDER_BIG_ENDIAN ) +return ioread16be (divider->reg); +else +return readw (divider->reg); + }else { +if (divider->flags &CLK_DIVIDER_BIG_ENDIAN ) +return ioread32be (divider->reg); +else +return readl (divider->reg); + } } -static inline void clk_div_writel (struct clk_divider *divider,u32 val) +static inline void clk_div_write (struct clk_divider *divider,u32 val) { -if (divider->flags &CLK_DIVIDER_BIG_ENDIAN ) -iowrite32be (val, divider->reg); -else -writel (val, divider->reg); +if (divider->flags &CLK_DIVIDER_REG_8BIT ) +writeb (val, divider->reg); +else if (divider->flags &CLK_DIVIDER_REG_16BIT ) { +if (divider->flags &CLK_DIVIDER_BIG_ENDIAN ) +iowrite16be (val, divider->reg); +else +writew (val, divider->reg); + }else { +if (divider->flags &CLK_DIVIDER_BIG_ENDIAN ) +iowrite32be (val, divider->reg); +else +writel (val, divider->reg); + } } static unsigned int _get_table_maxdiv(const struct clk_div_table *table,
@@ -152,7 +170,7 @@ static unsigned long clk_divider_recalc_rate(struct clk_hw *hw,struct clk_divider *divider =to_clk_divider (hw);unsigned int val; - val =clk_div_readl (divider) >> divider->shift; + val =clk_div_read (divider) >> divider->shift; val &=clk_div_mask (divider->width); return divider_recalc_rate(hw, parent_rate, val, divider->table,
@@ -434,7 +452,7 @@ static long clk_divider_round_rate(struct clk_hw *hw, unsigned long rate,if (divider->flags &CLK_DIVIDER_READ_ONLY ) {u32 val; - val =clk_div_readl (divider) >> divider->shift; + val =clk_div_read (divider) >> divider->shift; val &=clk_div_mask (divider->width); return divider_ro_round_rate(hw, rate, prate, divider->table,
@@ -455,7 +473,7 @@ static int clk_divider_determine_rate(struct clk_hw *hw,if (divider->flags &CLK_DIVIDER_READ_ONLY ) {u32 val; - val =clk_div_readl (divider) >> divider->shift; + val =clk_div_read (divider) >> divider->shift; val &=clk_div_mask (divider->width); return divider_ro_determine_rate(hw, req, divider->table,
@@ -505,11 +523,11 @@ static int clk_divider_set_rate(struct clk_hw *hw, unsigned long rate,if (divider->flags &CLK_DIVIDER_HIWORD_MASK ) { val =clk_div_mask (divider->width) << (divider->shift +16 ); }else { - val =clk_div_readl (divider); + val =clk_div_read (divider); val &= ~(clk_div_mask (divider->width) << divider->shift); } val |= (u32 )value << divider->shift; -clk_div_writel (divider, val); +clk_div_write (divider, val);if (divider->lock)spin_unlock_irqrestore (divider->lock, flags);
@@ -538,7 +556,7 @@ struct clk_hw *__clk_hw_register_divider(struct device *dev, struct device_node *np, const char *name, const char *parent_name, const struct clk_hw *parent_hw, const struct clk_parent_data *parent_data, unsigned long flags, - void __iomem *reg, u8 shift, u8 width, u8 clk_divider_flags, + void __iomem *reg, u8 shift, u8 width, u32 clk_divider_flags, const struct clk_div_table *table, spinlock_t *lock) { struct clk_divider *div;
@@ -610,7 +628,7 @@ EXPORT_SYMBOL_GPL(__clk_hw_register_divider);struct clk *clk_register_divider_table (struct device *dev,const char *name,const char *parent_name,unsigned long flags,void __iomem *reg,u8 shift,u8 width, -u8 clk_divider_flags,const struct clk_div_table *table, +u32 clk_divider_flags,const struct clk_div_table *table,spinlock_t *lock) {struct clk_hw *hw;
@@ -664,7 +682,7 @@ struct clk_hw *__devm_clk_hw_register_divider(struct device *dev, struct device_node *np, const char *name, const char *parent_name, const struct clk_hw *parent_hw, const struct clk_parent_data *parent_data, unsigned long flags, - void __iomem *reg, u8 shift, u8 width, u8 clk_divider_flags, + void __iomem *reg, u8 shift, u8 width, u32 clk_divider_flags, const struct clk_div_table *table, spinlock_t *lock) { struct clk_hw **ptr, *hw;
drivers/clk/clk-gate.c +49 -13
102 lines not on this page · raw message
include/linux/clk-provider.h +17 -5
@@ -508,12 +508,16 @@ void of_fixed_clk_setup(struct device_node *np);* CLK_GATE_BIG_ENDIAN - by default little endian register accesses are used for * the gate register. Setting this flag makes the register accesses big * endian. +* CLK_GATE_REG_8BIT - by default 32bit register accesses are used for +* the gate register. Setting this flag makes the register accesses 8bit. +* CLK_GATE_REG_16BIT - by default 32bit register accesses are used for +* the gate register. Setting this flag makes the register accesses 16bit. */ struct clk_gate {struct clk_hw hw;void __iomem *reg;u8 bit_idx; -u8 flags; +u32 flags;spinlock_t *lock; };
@@ -522,6 +526,8 @@ struct clk_gate {#define CLK_GATE_SET_TO_DISABLE BIT(0)#define CLK_GATE_HIWORD_MASK BIT(1)#define CLK_GATE_BIG_ENDIAN BIT(2) +#define CLK_GATE_REG_8BIT BIT(3) +#define CLK_GATE_REG_16BIT BIT(4)extern const struct clk_ops clk_gate_ops; struct clk_hw *__clk_hw_register_gate(struct device *dev,
@@ -675,13 +681,17 @@ struct clk_div_table {* CLK_DIVIDER_BIG_ENDIAN - By default little endian register accesses are used * for the divider register. Setting this flag makes the register accesses * big endian. +* CLK_DIVIDER_REG_8BIT - by default 32bit register accesses are used for +* the gate register. Setting this flag makes the register accesses 8bit. +* CLK_DIVIDER_REG_16BIT - by default 32bit register accesses are used for +* the gate register. Setting this flag makes the register accesses 16bit. */ struct clk_divider {struct clk_hw hw;void __iomem *reg;u8 shift;u8 width; -u8 flags; +u16 flags;const struct clk_div_table *table;spinlock_t *lock; };
@@ -697,6 +707,8 @@ struct clk_divider {#define CLK_DIVIDER_READ_ONLY BIT(5)#define CLK_DIVIDER_MAX_AT_ZERO BIT(6)#define CLK_DIVIDER_BIG_ENDIAN BIT(7) +#define CLK_DIVIDER_REG_8BIT BIT(8) +#define CLK_DIVIDER_REG_16BIT BIT(9)extern const struct clk_ops clk_divider_ops;extern const struct clk_ops clk_divider_ro_ops;
@@ -726,18 +738,18 @@ struct clk_hw *__clk_hw_register_divider(struct device *dev, struct device_node *np, const char *name, const char *parent_name, const struct clk_hw *parent_hw, const struct clk_parent_data *parent_data, unsigned long flags, - void __iomem *reg, u8 shift, u8 width, u8 clk_divider_flags, + void __iomem *reg, u8 shift, u8 width, u32 clk_divider_flags, const struct clk_div_table *table, spinlock_t *lock);struct clk_hw *__devm_clk_hw_register_divider (struct device *dev,struct device_node *np,const char *name,const char *parent_name,const struct clk_hw *parent_hw,const struct clk_parent_data *parent_data,unsigned long flags, -void __iomem *reg,u8 shift,u8 width,u8 clk_divider_flags, +void __iomem *reg,u8 shift,u8 width,u32 clk_divider_flags,const struct clk_div_table *table,spinlock_t *lock);struct clk *clk_register_divider_table (struct device *dev,const char *name,const char *parent_name,unsigned long flags,void __iomem *reg,u8 shift,u8 width, -u8 clk_divider_flags,const struct clk_div_table *table, +u32 clk_divider_flags,const struct clk_div_table *table,spinlock_t *lock);/** * clk_register_divider - register a divider clock with the clock framework
Signature · 1 line
2.39.2
Re: [RESEND v7 14/37] clk: Compatible with narrow registers
Hi Sato-san,
Quoted 8 lines · Yoshinori Sato
divider and gate only support 32-bit registers.
Older hardware uses narrower registers, so I want to be able to handle 8-bit and 16-bit wide registers.Seven
clk_dividerflags are used, and if I add flags for 8bit access and 16bit access, 8bit will not be enough, so I expanded it to u16.Signed-off-by Yoshinori Sato <[email protected]>
Thanks for the update!
Quoted 5 lines
drivers/clk/clk-divider.c +0
-0@@ -26,20 +26,38 @@* parent - fixed parent. No clk_set_parent support */
drivers/clk/clk-divider.c line 31
Quoted 10 lines
drivers/clk/clk-divider.c +3
-6-static inline u32 clk_div_readl (struct clk_divider *divider) -{ -if (divider->flags &CLK_DIVIDER_BIG_ENDIAN ) -return ioread32be (divider->reg); - -return readl (divider->reg); +static inline u32 clk_div_read (struct clk_divider *divider) +{ +if (divider->flags &CLK_DIVIDER_REG_8BIT )
When you need curly braces in one branch of an if/else statement, please use curly braces in all branches (everywhere).
Quoted 31 lines
drivers/clk/clk-divider.c +12
-0+return readb (divider->reg); + else if (divider->flags & CLK_DIVIDER_REG_16BIT) { +if (divider->flags &CLK_DIVIDER_BIG_ENDIAN ) +return ioread16be (divider->reg); +else +return readw (divider->reg); + } else { +if (divider->flags &CLK_DIVIDER_BIG_ENDIAN ) +return ioread32be (divider->reg); +else +return readl (divider->reg); + } }drivers/clk/clk-gate.c +4
-0@@ -137,12 +155,30 @@ struct clk_hw *__clk_hw_register_gate(struct device *dev,struct clk_init_data init = {};int ret = -EINVAL ; +/* validate register size option and bit_idx */ if (clk_gate_flags &CLK_GATE_HIWORD_MASK ) {if (bit_idx >15 ) {pr_err ("gate bit exceeds LOWORD field\n" );return ERR_PTR (-EINVAL ); } } +if (clk_gate_flags &CLK_GATE_REG_16BIT ) { +if (bit_idx >15 ) { +pr_err ("gate bit exceeds 16 bits\n" );
drivers/clk/clk-gate.c struct clk_hw *__clk_hw_register_gate(struct device *dev, · line 177
Quoted 10 lines
drivers/clk/clk-gate.c +10
-0+return ERR_PTR (-EINVAL ); + } + } +if (clk_gate_flags &CLK_GATE_REG_8BIT ) { +if (bit_idx >7 ) { +pr_err ("gate bit exceeds 8 bits\n" ); +return ERR_PTR (-EINVAL ); + } + } + if ((clk_gate_flags & CLK_GATE_HIWORD_MASK) &&
If you use parentheses around "a & b" here...
drivers/clk/clk-gate.c struct clk_hw *__clk_hw_register_gate(struct device *dev, · line 178
Quoted 1 line
drivers/clk/clk-gate.c +1
-0+ clk_gate_flags & (CLK_GATE_REG_8BIT | CLK_GATE_REG_16BIT)) {
please add parentheses here, too.
Quoted 15 lines
drivers/clk/clk-gate.c +3
-0+pr_err ("HIWORD_MASK required 32-bit register\n" ); +return ERR_PTR (-EINVAL ); + }/* allocate the gate */ gate =kzalloc (sizeof (*gate),GFP_KERNEL );include/linux/clk-provider.h +1
-0@@ -508,12 +508,16 @@ void of_fixed_clk_setup(struct device_node *np);* CLK_GATE_BIG_ENDIAN - by default little endian register accesses are used for * the gate register. Setting this flag makes the register accesses big * endian. +* CLK_GATE_REG_8BIT - by default 32bit register accesses are used for
include/linux/clk-provider.h void of_fixed_clk_setup(struct device_node *np); · line 520
Quoted 10 lines
include/linux/clk-provider.h +4
-1+* the gate register. Setting this flag makes the register accesses 8bit. +* CLK_GATE_REG_16BIT - by default 32bit register accesses are used for +* the gate register. Setting this flag makes the register accesses 16bit. */ struct clk_gate {struct clk_hw hw;void __iomem *reg;u8 bit_idx; -u8 flags; +u32 flags;
(from my comments on v6)
There is no need to increase the size of the flags field for the gate clock.
Quoted 25 lines
include/linux/clk-provider.h +5
-1spinlock_t *lock; };@@ -675,13 +681,17 @@ struct clk_div_table {* CLK_DIVIDER_BIG_ENDIAN - By default little endian register accesses are used * for the divider register. Setting this flag makes the register accesses * big endian. +* CLK_DIVIDER_REG_8BIT - by default 32bit register accesses are used for +* the gate register. Setting this flag makes the register accesses 8bit. +* CLK_DIVIDER_REG_16BIT - by default 32bit register accesses are used for +* the gate register. Setting this flag makes the register accesses 16bit. */ struct clk_divider {struct clk_hw hw;void __iomem *reg;u8 shift;u8 width; -u8 flags; +u16 flags;const struct clk_div_table *table;spinlock_t *lock; };
include/linux/clk-provider.h struct clk_hw *__clk_hw_register_divider(struct device *dev, · line 741
Quoted 5 lines
include/linux/clk-provider.h +1
-1@@ -726,18 +738,18 @@ struct clk_hw *__clk_hw_register_divider(struct device *dev, struct device_node *np, const char *name, const char *parent_name, const struct clk_hw *parent_hw, const struct clk_parent_data *parent_data, unsigned long flags, - void __iomem *reg, u8 shift, u8 width, u8 clk_divider_flags, + void __iomem *reg, u8 shift, u8 width, u32 clk_divider_flags,
"u16 clk_divider_flags", to match clk_divider.flags.
include/linux/clk-provider.h struct clk_hw *__clk_hw_register_divider(struct device *dev, · line 747
Quoted 7 lines
include/linux/clk-provider.h +1
-1const struct clk_div_table *table, spinlock_t *lock); struct clk_hw *__devm_clk_hw_register_divider(struct device *dev, struct device_node *np, const char *name, const char *parent_name, const struct clk_hw *parent_hw, const struct clk_parent_data *parent_data, unsigned long flags, - void __iomem *reg, u8 shift, u8 width, u8 clk_divider_flags, + void __iomem *reg, u8 shift, u8 width, u32 clk_divider_flags,
Likewise.
include/linux/clk-provider.h struct clk_hw *__clk_hw_register_divider(struct device *dev, · line 752
Quoted 6 lines
include/linux/clk-provider.h +1
-1const struct clk_div_table *table, spinlock_t *lock); struct clk *clk_register_divider_table(struct device *dev, const char *name, const char *parent_name, unsigned long flags, void __iomem *reg, u8 shift, u8 width, - u8 clk_divider_flags, const struct clk_div_table *table, + u32 clk_divider_flags, const struct clk_div_table *table,
Likewise.
include/linux/clk-provider.h struct clk_hw *__clk_hw_register_divider(struct device *dev, · line 755
Quoted 3 lines
include/linux/clk-provider.h +0
-0spinlock_t *lock);/** * clk_register_divider - register a divider clock with the clock framework
Gr{oetje,eeting}s,
Geert
Signature · 5 lines
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected] In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds
Damien Le Moal
maintainerRe: [RESEND v7 14/37] clk: Compatible with narrow registers
Quoted 21 lines · Geert Uytterhoeven
Hi Sato-san,
Quoted 8 lines · Yoshinori Sato
divider and gate only support 32-bit registers.
Older hardware uses narrower registers, so I want to be able to handle 8-bit and 16-bit wide registers.Seven
clk_dividerflags are used, and if I add flags for 8bit access and 16bit access, 8bit will not be enough, so I expanded it to u16.Signed-off-by Yoshinori Sato <[email protected]>Thanks for the update!
Quoted 6 lines
drivers/clk/clk-divider.c +0
-0@@ -26,20 +26,38 @@* parent - fixed parent. No clk_set_parent support */
Quoted 15 lines
drivers/clk/clk-divider.c line 31
Quoted 9 lines
drivers/clk/clk-divider.c +3
-6-static inline u32 clk_div_readl (struct clk_divider *divider) -{ -if (divider->flags &CLK_DIVIDER_BIG_ENDIAN ) -return ioread32be (divider->reg); - -return readl (divider->reg); +static inline u32 clk_div_read (struct clk_divider *divider) +{ +if (divider->flags &CLK_DIVIDER_REG_8BIT )When you need curly braces in one branch of an if/else statement, please use curly braces in all branches (everywhere).
Quoted 2 lines
drivers/clk/clk-divider.c +2
-0+return readb (divider->reg); + else if (divider->flags & CLK_DIVIDER_REG_16BIT) {
And no need for an else after a return...
Quoted 3 lines
drivers/clk/clk-divider.c line 36
Quoted 3 lines
drivers/clk/clk-divider.c +3
-0+if (divider->flags &CLK_DIVIDER_BIG_ENDIAN ) +return ioread16be (divider->reg); +else
and here.
Quoted 5 lines
drivers/clk/clk-divider.c line 41
Quoted 5 lines
drivers/clk/clk-divider.c +5
-0+return readw (divider->reg); + }else { +if (divider->flags &CLK_DIVIDER_BIG_ENDIAN ) +return ioread32be (divider->reg); +else
here too.
Quoted 128 lines
Quoted 21 lines
drivers/clk/clk-divider.c +2
-0+return readl (divider->reg); + } }drivers/clk/clk-gate.c +4
-0@@ -137,12 +155,30 @@ struct clk_hw *__clk_hw_register_gate(struct device *dev,struct clk_init_data init = {};int ret = -EINVAL ; +/* validate register size option and bit_idx */ if (clk_gate_flags &CLK_GATE_HIWORD_MASK ) {if (bit_idx >15 ) {pr_err ("gate bit exceeds LOWORD field\n" );return ERR_PTR (-EINVAL ); } } +if (clk_gate_flags &CLK_GATE_REG_16BIT ) { +if (bit_idx >15 ) { +pr_err ("gate bit exceeds 16 bits\n" );drivers/clk/clk-gate.c struct clk_hw *__clk_hw_register_gate(struct device *dev, · line 177
Quoted 10 lines
drivers/clk/clk-gate.c +10
-0+return ERR_PTR (-EINVAL ); + } + } +if (clk_gate_flags &CLK_GATE_REG_8BIT ) { +if (bit_idx >7 ) { +pr_err ("gate bit exceeds 8 bits\n" ); +return ERR_PTR (-EINVAL ); + } + } + if ((clk_gate_flags & CLK_GATE_HIWORD_MASK) &&If you use parentheses around "a & b" here...
drivers/clk/clk-gate.c struct clk_hw *__clk_hw_register_gate(struct device *dev, · line 178
Quoted 1 line
drivers/clk/clk-gate.c +1
-0+ clk_gate_flags & (CLK_GATE_REG_8BIT | CLK_GATE_REG_16BIT)) {please add parentheses here, too.
Quoted 15 lines
drivers/clk/clk-gate.c +3
-0+pr_err ("HIWORD_MASK required 32-bit register\n" ); +return ERR_PTR (-EINVAL ); + }/* allocate the gate */ gate =kzalloc (sizeof (*gate),GFP_KERNEL );include/linux/clk-provider.h +1
-0@@ -508,12 +508,16 @@ void of_fixed_clk_setup(struct device_node *np);* CLK_GATE_BIG_ENDIAN - by default little endian register accesses are used for * the gate register. Setting this flag makes the register accesses big * endian. +* CLK_GATE_REG_8BIT - by default 32bit register accesses are used for include/linux/clk-provider.h void of_fixed_clk_setup(struct device_node *np); · line 520
Quoted 10 lines
include/linux/clk-provider.h +4
-1+* the gate register. Setting this flag makes the register accesses 8bit. +* CLK_GATE_REG_16BIT - by default 32bit register accesses are used for +* the gate register. Setting this flag makes the register accesses 16bit. */ struct clk_gate {struct clk_hw hw;void __iomem *reg;u8 bit_idx; -u8 flags; +u32 flags;(from my comments on v6)
There is no need to increase the size of the flags field for the gate clock.Quoted 25 lines
include/linux/clk-provider.h +5
-1spinlock_t *lock; };@@ -675,13 +681,17 @@ struct clk_div_table {* CLK_DIVIDER_BIG_ENDIAN - By default little endian register accesses are used * for the divider register. Setting this flag makes the register accesses * big endian. +* CLK_DIVIDER_REG_8BIT - by default 32bit register accesses are used for +* the gate register. Setting this flag makes the register accesses 8bit. +* CLK_DIVIDER_REG_16BIT - by default 32bit register accesses are used for +* the gate register. Setting this flag makes the register accesses 16bit. */ struct clk_divider {struct clk_hw hw;void __iomem *reg;u8 shift;u8 width; -u8 flags; +u16 flags;const struct clk_div_table *table;spinlock_t *lock; };include/linux/clk-provider.h struct clk_hw *__clk_hw_register_divider(struct device *dev, · line 741
Quoted 5 lines
include/linux/clk-provider.h +1
-1@@ -726,18 +738,18 @@ struct clk_hw *__clk_hw_register_divider(struct device *dev, struct device_node *np, const char *name, const char *parent_name, const struct clk_hw *parent_hw, const struct clk_parent_data *parent_data, unsigned long flags, - void __iomem *reg, u8 shift, u8 width, u8 clk_divider_flags, + void __iomem *reg, u8 shift, u8 width, u32 clk_divider_flags,"u16
clk_divider_flags", to match clk_divider.flags.include/linux/clk-provider.h struct clk_hw *__clk_hw_register_divider(struct device *dev, · line 747
Quoted 7 lines
include/linux/clk-provider.h +1
-1const struct clk_div_table *table, spinlock_t *lock); struct clk_hw *__devm_clk_hw_register_divider(struct device *dev, struct device_node *np, const char *name, const char *parent_name, const struct clk_hw *parent_hw, const struct clk_parent_data *parent_data, unsigned long flags, - void __iomem *reg, u8 shift, u8 width, u8 clk_divider_flags, + void __iomem *reg, u8 shift, u8 width, u32 clk_divider_flags,Likewise.
include/linux/clk-provider.h struct clk_hw *__clk_hw_register_divider(struct device *dev, · line 752
Quoted 6 lines
include/linux/clk-provider.h +1
-1const struct clk_div_table *table, spinlock_t *lock); struct clk *clk_register_divider_table(struct device *dev, const char *name, const char *parent_name, unsigned long flags, void __iomem *reg, u8 shift, u8 width, - u8 clk_divider_flags, const struct clk_div_table *table, + u32 clk_divider_flags, const struct clk_div_table *table,Likewise.
include/linux/clk-provider.h struct clk_hw *__clk_hw_register_divider(struct device *dev, · line 755
Quoted 3 lines
include/linux/clk-provider.h +0
-0spinlock_t *lock);/** * clk_register_divider - register a divider clock with the clock framework Gr{oetje,eeting}s,
Geert
Signature · 2 lines
Damien Le Moal Western Digital Research
Yoshinori Sato
maintainerPATCH RESEND v7 15/37 clk: renesas: Add SH7750/7751 CPG Driver
In reply to a message not in the archiveRenesas SH7750 and SH7751 series CPG driver. This driver supported frequency control and clock gating.
--- drivers/clk/renesas/Kconfig | 13 +- drivers/clk/renesas/Makefile | 1 + drivers/clk/renesas/clk-sh7750.c | 480 +++++++++++++++++++++++++++++++ 3 files changed, 491 insertions(+), 3 deletions(-) create mode 100644 drivers/clk/renesas/clk-sh7750.c
drivers/clk/renesas/Kconfig +10 -3
@@ -1,8 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 config CLK_RENESAS - bool "Renesas SoC clock support" if COMPILE_TEST && !ARCH_RENESAS - default y if ARCH_RENESAS + bool "Renesas SoC clock support" if COMPILE_TEST && !ARCH_RENESAS && !SUPERH + default y if ARCH_RENESAS || SUPERH select CLK_EMEV2 if ARCH_EMEV2 select CLK_RZA1 if ARCH_R7S72100 select CLK_R7S9210 if ARCH_R7S9210
@@ -41,6 +41,9 @@ config CLK_RENESAS select CLK_R9A08G045 if ARCH_R9A08G045 select CLK_R9A09G011 if ARCH_R9A09G011 select CLK_SH73A0 if ARCH_SH73A0 + select CLK_SH7750 if CPU_SUBTYPE_SH7750 || CPU_SUBTYPE_SH7750S || \ + CPU_SUBTYPE_SH7750R || CPU_SUBTYPE_SH7751 || \ + CPU_SUBTYPE_SH7751R if CLK_RENESAS
@@ -198,7 +201,6 @@ config CLK_SH73A0 select CLK_RENESAS_CPG_MSTP select CLK_RENESAS_DIV6 - # Family config CLK_RCAR_CPG_LIB bool "CPG/MSSR library functions" if COMPILE_TEST
@@ -228,6 +230,11 @@ config CLK_RZG2L bool "Renesas RZ/{G2L,G2UL,G3S,V2L} family clock support" if COMPILE_TEST select RESET_CONTROLLER +config CLK_SH7750 + bool "Renesas SH7750/7751 family clock support" if COMPILE_TEST + help + This is a driver for SH7750 / SH7751 CPG. + # Generic config CLK_RENESAS_CPG_MSSR bool "CPG/MSSR clock support" if COMPILE_TEST
drivers/clk/renesas/Makefile +1 -0
@@ -38,6 +38,7 @@ obj-$(CONFIG_CLK_R9A07G054) += r9a07g044-cpg.o obj-$(CONFIG_CLK_R9A08G045) += r9a08g045-cpg.o obj-$(CONFIG_CLK_R9A09G011) += r9a09g011-cpg.o obj-$(CONFIG_CLK_SH73A0) += clk-sh73a0.o +obj-$(CONFIG_CLK_SH7750) += clk-sh7750.o # Family obj-$(CONFIG_CLK_RCAR_CPG_LIB) += rcar-cpg-lib.o
drivers/clk/renesas/clk-sh7750.c new file +480 -0
480 lines not on this page · raw message
Signature · 1 line
2.39.2
Re: [RESEND v7 15/37] clk: renesas: Add SH7750/7751 CPG Driver
Hi Sato-san,
Quoted 4 lines · Yoshinori Sato
Renesas SH7750 and SH7751 series CPG driver. This driver supported frequency control and clock gating.
Signed-off-by Yoshinori Sato <[email protected]>
Thanks for the update!
As you plan to send a v8 soon, I'm sending you a comment from the (incomplete) review I started a while ago...
Quoted 12 lines
drivers/clk/renesas/clk-sh7750.c new file +9
-0+static int register_pll (struct device_node *node,struct cpg_priv *cpg) +{ +const char *clk_name = node->name; +const char *parent_name; +struct clk_init_data init = { + .name =PLLOUT , + .ops = &pll_ops, + .flags =0 , + .num_parents =1 ,
drivers/clk/renesas/clk-sh7750.c line 190
Quoted 10 lines
drivers/clk/renesas/clk-sh7750.c new file +10
-0+ }; +int ret; + + parent_name =of_clk_get_parent_name (node,0 ); + init.parent_names = &parent_name; + cpg->hw.init = &init; + + ret =of_clk_hw_register (node, &cpg->hw); +if (ret <0 ) + pr_err("%pOF: failed to add provider %s (%d)\n",
I think you retained the wrong error message?
"%s: failed to register %s pll clock (%d)\n" sounds more suitable to me.
drivers/clk/renesas/clk-sh7750.c line 193
Quoted 3 lines
drivers/clk/renesas/clk-sh7750.c new file +3
-0+ node, clk_name, ret); +return ret; +}
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]
In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
Yoshinori Sato
maintainerPATCH RESEND v7 16/37 irqchip: Add SH7751 INTC driver
In reply to a message not in the archiveRenesas SH7751 Internal interrupt controller driver.
--- drivers/irqchip/Kconfig | 8 + drivers/irqchip/Makefile | 1 + drivers/irqchip/irq-renesas-sh7751.c | 282 +++++++++++++++++++++++++++ 3 files changed, 291 insertions(+) create mode 100644 drivers/irqchip/irq-renesas-sh7751.c
drivers/irqchip/Kconfig +8 -0
@@ -690,4 +690,12 @@ config SUNPLUS_SP7021_INTC chained controller, routing all interrupt source in P-Chip to the primary controller on C-Chip. +config RENESAS_SH7751_INTC + bool "Renesas SH7751 Interrupt Controller" + depends on SH_DEVICE_TREE || COMPILE_TEST + select IRQ_DOMAIN_HIERARCHY + help + Support for the Renesas SH7751 On-chip interrupt controller. + And external interrupt encoder for some targets. + endmenu
drivers/irqchip/Makefile +1 -0
@@ -121,3 +121,4 @@ obj-$(CONFIG_IRQ_IDT3243X) += irq-idt3243x.o obj-$(CONFIG_APPLE_AIC) += irq-apple-aic.o obj-$(CONFIG_MCHP_EIC) += irq-mchp-eic.o obj-$(CONFIG_SUNPLUS_SP7021_INTC) += irq-sp7021-intc.o +obj-$(CONFIG_RENESAS_SH7751_INTC) += irq-renesas-sh7751.o
drivers/irqchip/irq-renesas-sh7751.c new file +282 -0
282 lines not on this page · raw message
Signature · 1 line
2.39.2
Yoshinori Sato
maintainerPATCH RESEND v7 17/37 dt-bindings: interrupt-controller: renesas,sh7751-intc: Add json-schema
In reply to a message not in the archiveRenesas SH7751 INTC json-schema.
--- .../renesas,sh7751-intc.yaml | 53 +++++++++++++++++++ 1 file changed, 53 insertions(+) create mode 100644 Documentation/devicetree/bindings/interrupt-controller/renesas,sh7751-intc.yaml
Documentation/devicetree/bindings/interrupt-controller/renesas,sh7751-intc.yaml new file +53 -0
@@ -0,0 +1,53 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/interrupt-controller/renesas,sh7751-intc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas SH7751 Interrupt Controller + +maintainers: + - Yoshinori Sato <[email protected]> + +properties: + compatible: + items: + - const: renesas,sh7751-intc + + '#interrupt-cells': + const: 1 + + interrupt-controller: true + + reg: + maxItems: 2 + + reg-names: + items: + - const: ICR + - const: INTPRI00 + + renesas,icr-irlm: + $ref: /schemas/types.yaml#/definitions/flag + description: If true four independent interrupt requests mode (ICR.IRLM is 1). + +required: + - compatible + - reg + - reg-names + - '#interrupt-cells' + - interrupt-controller + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/renesas,sh7751-intc.h> + shintc: interrupt-controller@ffd00000 { + compatible = "renesas,sh7751-intc"; + reg = <0xffd00000 14>, <0xfe080000 128>; + reg-names = "ICR", "INTPRI00"; + #interrupt-cells = <1>; + interrupt-controller; + }; +...
Signature · 1 line
2.39.2
Re: [RESEND v7 17/37] dt-bindings: interrupt-controller: renesas,sh7751-intc: Add json-schema
Quoted 8 lines · Yoshinori Sato
Renesas SH7751 INTC json-schema.
Signed-off-by Yoshinori Sato <[email protected]>--- .../renesas,sh7751-intc.yaml | 53 +++++++++++++++++++ 1 file changed, 53 insertions(+) create mode 100644 Documentation/devicetree/bindings/interrupt-controller/renesas,sh7751-intc.yaml
Yoshinori Sato
maintainerPATCH RESEND v7 18/37 irqchip: SH7751 external interrupt encoder with enable gate.
In reply to a message not in the archiveSH7751 have 15 level external interrupt.
It is typically connected to the CPU through a priority encoder that can suppress requests.
This driver provides a way to control those hardware with irqchip.
--- drivers/irqchip/Kconfig | 7 + drivers/irqchip/Makefile | 2 + drivers/irqchip/irq-renesas-sh7751irl.c | 221 ++++++++++++++++++++++++ 3 files changed, 230 insertions(+) create mode 100644 drivers/irqchip/irq-renesas-sh7751irl.c
drivers/irqchip/Kconfig +7 -0
@@ -698,4 +698,11 @@ config RENESAS_SH7751_INTC Support for the Renesas SH7751 On-chip interrupt controller. And external interrupt encoder for some targets. +config RENESAS_SH7751IRL_INTC + bool "Renesas SH7751 based target IRL encoder support." + depends on RENESAS_SH7751_INTC + help + Support for External Interrupt encoder + on the some Renesas SH7751 based target. + endmenu
drivers/irqchip/Makefile +2 -0
@@ -122,3 +122,5 @@ obj-$(CONFIG_APPLE_AIC) += irq-apple-aic.o obj-$(CONFIG_MCHP_EIC) += irq-mchp-eic.o obj-$(CONFIG_SUNPLUS_SP7021_INTC) += irq-sp7021-intc.o obj-$(CONFIG_RENESAS_SH7751_INTC) += irq-renesas-sh7751.o +obj-$(CONFIG_RENESAS_SH7751IRL_INTC) += irq-renesas-sh7751irl.o +
drivers/irqchip/irq-renesas-sh7751irl.c new file +221 -0
221 lines not on this page · raw message
Signature · 1 line
2.39.2
Yoshinori Sato
maintainerPATCH RESEND v7 19/37 dt-bindings: interrupt-controller: renesas,sh7751-irl-ext: Add json-schema
In reply to a message not in the archiveRenesas SH7751 external interrupt encoder json-schema.
--- .../renesas,sh7751-irl-ext.yaml | 57 +++++++++++++++++++ 1 file changed, 57 insertions(+) create mode 100644 Documentation/devicetree/bindings/interrupt-controller/renesas,sh7751-irl-ext.yaml
Documentation/devicetree/bindings/interrupt-controller/renesas,sh7751-irl-ext.yaml new file +57 -0
@@ -0,0 +1,57 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/interrupt-controller/renesas,sh7751-irl-ext.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas SH7751 external interrupt encoder with enable regs. + +maintainers: + - Yoshinori Sato <[email protected]> + +description: + This is the generally used external interrupt encoder on SH7751 based boards. + +properties: + compatible: + items: + - const: renesas,sh7751-irl-ext + + reg: true + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + + '#address-cells': + const: 0 + + renesas,set-to-disable: + $ref: /schemas/types.yaml#/definitions/flag + description: Invert enable registers. Setting the bit to 0 enables interrupts. + + renesas,enable-reg: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: | + IRQ enable register bit mapping + +required: + - compatible + - reg + - interrupt-controller + - '#interrupt-cells' + - renesas,enable-reg + +additionalProperties: false + +examples: + - | + r2dintc: interrupt-controller@a4000000 { + compatible = "renesas,sh7751-irl-ext"; + reg = <0xa4000000 0x02>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + renesas,enable-reg = <12 9 10 3 0 4 1 2 8 5 6 7 15 15 15 11>; + };
Signature · 1 line
2.39.2
Rob Herring
maintainerRe: [RESEND v7 19/37] dt-bindings: interrupt-controller: renesas,sh7751-irl-ext: Add json-schema
Quoted 8 lines · Yoshinori Sato
Renesas SH7751 external interrupt encoder json-schema.
Signed-off-by Yoshinori Sato <[email protected]>--- .../renesas,sh7751-irl-ext.yaml | 57 +++++++++++++++++++ 1 file changed, 57 insertions(+) create mode 100644 Documentation/devicetree/bindings/interrupt-controller/renesas,sh7751-irl-ext.yaml
My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13):
yamllint warnings/errors:
dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/interrupt-controller/renesas,sh7751-irl-ext.example.dtb: interrupt-controller@a4000000: #interrupt-cells:0:0: 2 was expected
from schema $id: http://devicetree.org/schemas/interrupt-controller/renesas,sh7751-irl-ext.yaml#
doc reference errors (make refcheckdocs):
The base for the series is generally the latest rc1. A different dependency should be noted in *this* patch.
If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date:
pip3 install dtschema --upgrade
Please check and re-submit after running the above command yourself. Note that DT_SCHEMA_FILES can be set to your schema file to speed up checking your schema. However, it must be unset to test all examples with your schema.
Yoshinori Sato
maintainerPATCH RESEND v7 20/37 serial: sh-sci: fix SH4 OF support.
In reply to a message not in the archive- fix earlycon name.
- fix earlyprintk hung (NULL pointer reference).
- fix SERIAL_SH_SCI_EARLYCON enablement
--- drivers/tty/serial/Kconfig | 2 +- drivers/tty/serial/sh-sci.c | 6 +++--- 2 files changed, 4 insertions(+), 4 deletions(-)
drivers/tty/serial/Kconfig +1 -1
@@ -661,7 +661,7 @@ config SERIAL_SH_SCI_EARLYCON depends on SERIAL_SH_SCI=y select SERIAL_CORE_CONSOLE select SERIAL_EARLYCON - default ARCH_RENESAS + default ARCH_RENESAS || SUPERH config SERIAL_SH_SCI_DMA bool "DMA support" if EXPERT
drivers/tty/serial/sh-sci.c +3 -3
@@ -2717,7 +2717,7 @@ static int sci_remap_port(struct uart_port *port)if (port->membase)return 0 ; -if (port->dev->of_node || (port->flags &UPF_IOREMAP )) { +if ((port->dev && port->dev->of_node) || (port->flags &UPF_IOREMAP )) { port->membase =ioremap (port->mapbase, sport->reg_size);if (unlikely (!port->membase)) {dev_err (port->dev,"can't remap port#%d\n" , port->line);
@@ -3545,8 +3545,8 @@ static int __init hscif_early_console_setup(struct earlycon_device *device,OF_EARLYCON_DECLARE (sci,"renesas,sci" , sci_early_console_setup);OF_EARLYCON_DECLARE (scif,"renesas,scif" , scif_early_console_setup); -OF_EARLYCON_DECLARE (scif,"renesas,scif-r7s9210" , rzscifa_early_console_setup); -OF_EARLYCON_DECLARE (scif,"renesas,scif-r9a07g044" , rzscifa_early_console_setup); +OF_EARLYCON_DECLARE (rzscifa,"renesas,scif-r7s9210" , rzscifa_early_console_setup); +OF_EARLYCON_DECLARE (rzscifa,"renesas,scif-r9a07g044" , rzscifa_early_console_setup);OF_EARLYCON_DECLARE (scifa,"renesas,scifa" , scifa_early_console_setup);OF_EARLYCON_DECLARE (scifb,"renesas,scifb" , scifb_early_console_setup);OF_EARLYCON_DECLARE (hscif,"renesas,hscif" , hscif_early_console_setup);
Signature · 1 line
2.39.2
Yoshinori Sato
maintainerPATCH RESEND v7 21/37 dt-bindings: serial: renesas,scif: Add scif-sh7751.
In reply to a message not in the archiveAdd Renesas SH7751 SCIF.
--- Documentation/devicetree/bindings/serial/renesas,scif.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/serial/renesas,scif.yaml +1 -0
@@ -18,6 +18,7 @@ properties: - items: - enum: - renesas,scif-r7s72100 # RZ/A1H + - renesas,scif-sh7751 # SH7751 - const: renesas,scif # generic SCIF compatible UART - items:
Signature · 1 line
2.39.2
Re: [RESEND v7 21/37] dt-bindings: serial: renesas,scif: Add scif-sh7751.
Hi Sato-san,
Quoted 8 lines · Yoshinori Sato
Add Renesas SH7751 SCIF.
Signed-off-by Yoshinori Sato <[email protected]>Reviewed-by Geert Uytterhoeven <[email protected]>
Documentation/devicetree/bindings/serial/renesas,scif.yaml properties: · line 24
Quoted 7 lines
Documentation/devicetree/bindings/serial/renesas,scif.yaml +1
-0@@ -18,6 +18,7 @@ properties: - items: - enum: - renesas,scif-r7s72100 # RZ/A1H + - renesas,scif-sh7751 # SH7751 - const: renesas,scif # generic SCIF compatible UART - items:
If this is applied after "[PATCH v2 2/2] dt-bindings: serial:
renesas,scif: Validate 'interrupts' and 'interrupt-names'"[1], an extra "- renesas,scif-sh7751" line should be added to the 4-interrupt section (below "- renesas,scif-r7s72100").
[1] https://lore.kernel.org/all/[email protected]/
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]
In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
Yoshinori Sato
maintainerPATCH RESEND v7 22/37 dt-bindings: display: smi,sm501: SMI SM501 binding json-schema
In reply to a message not in the archive--- .../bindings/display/smi,sm501.yaml | 398 ++++++++++++++++++ 1 file changed, 398 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/smi,sm501.yaml
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +398 -0
@@ -0,0 +1,398 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/smi,sm501.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Silicon Motion SM501 Mobile Multimedia Companion Chip + +maintainers: + - Yoshinori Sato <[email protected]> + +description: | + These DT bindings describe the SM501. + +properties: + compatible: + const: + smi,sm501 + + reg: + maxItems: 2 + description: | + First entry: System Configuration register + Second entry: IO space (Display Controller register) + + interrupts: + description: SM501 interrupt to the cpu should be described here. + + mode: + $ref: /schemas/types.yaml#/definitions/string + description: select a video mode + + edid: + description: | + verbatim EDID data block describing attached display. + Data from the detailed timing descriptor will be used to + program the display controller. + + little-endian: + $ref: /schemas/types.yaml#/definitions/flag + description: available on big endian systems, to set different foreign endian. + big-endian: + $ref: /schemas/types.yaml#/definitions/flag + description: available on little endian systems, to set different foreign endian. + + swap-fb-endian: + $ref: /schemas/types.yaml#/definitions/flag + description: swap framebuffer byteorder. + + route-crt-panel: + $ref: /schemas/types.yaml#/definitions/flag + description: Panel output merge to CRT. + + crt: + type: object + description: CRT output control + properties: + edid: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + verbatim EDID data block describing attached display. + Data from the detailed timing descriptor will be used to + program the display controller. + + smi,flags: + $ref: /schemas/types.yaml#/definitions/string-array + description: Display control flags. + items: + anyOf: + - const: use-init-done + - const: disable-at-exit + - const: use-hwcursor + - const: use-hwaccel + - const: panel-no-fpen + - const: panel-no-vbiasen + - const: panel-inv-fpen + - const: panel-inv-vbiasen + maxItems: 8 + + bpp: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Color depth + + panel: + type: object + description: Panel output control + properties: + edid: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + verbatim EDID data block describing attached display. + Data from the detailed timing descriptor will be used to + program the display controller. + + smi,flags: + $ref: /schemas/types.yaml#/definitions/string-array + description: Display control flags. + items: + anyOf: + - const: use-init-done + - const: disable-at-exit + - const: use-hwcursor + - const: use-hwaccel + - const: panel-no-fpen + - const: panel-no-vbiasen + - const: panel-inv-fpen + - const: panel-inv-vbiasen + maxItems: 8 + + bpp: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Color depth + + smi,devices: + $ref: /schemas/types.yaml#/definitions/string-array + description: Select SM501 device functions. + items: + anyOf: + - const: usb-host + - const: usb-slave + - const: ssp0 + - const: ssp1 + - const: uart0 + - const: uart1 + - const: fbaccel + - const: ac97 + - const: i2s + - const: gpio + minItems: 1 + maxItems: 10 + + smi,mclk: + $ref: /schemas/types.yaml#/definitions/uint32 + description: mclk frequency. + + smi,m1xclk: + $ref: /schemas/types.yaml#/definitions/uint32 + description: m1xclk frequency. + + misc-timing: + type: object + description: Miscellaneous Timing register values. + properties: + ex: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Extend bus holding time. + + xc: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Xscale clock input select. + + usb-over-current-detect-disable: + $ref: /schemas/types.yaml#/definitions/flag + description: USB host current detection disable (Us=0). + + usb-over-current-detect-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: USB host current detection disable (Us=1). + + sdram-clock-mode1-288mhz: + $ref: /schemas/types.yaml#/definitions/flag + description: SSM1 bit is clear. + + sdram-clock-mode1-div: + $ref: /schemas/types.yaml#/definitions/flag + description: SSM1 bit is set. + + sm1: + $ref: /schemas/types.yaml#/definitions/flag + description: SDRAM clock divider for PW mode 1. + + sdram-clock-mode0-288mhz: + $ref: /schemas/types.yaml#/definitions/flag + description: SSM0 bit is clear. + + sdram-clock-mode0-div: + $ref: /schemas/types.yaml#/definitions/flag + description: SSM0 bit is set. + + sm0: + $ref: /schemas/types.yaml#/definitions/uint32 + description: SDRAM clock divider for PW mode 0. + + pll-debug-input: + $ref: /schemas/types.yaml#/definitions/flag + description: 96MHz PLL debug input reference frequency (Deb=0). + + pll-debug-output: + $ref: /schemas/types.yaml#/definitions/flag + description: 96MHz PLL debug output frequency (Deb=1). + + no-acpi-control: + $ref: /schemas/types.yaml#/definitions/flag + description: No ACPI control (A=0). + + acpi-control: + $ref: /schemas/types.yaml#/definitions/flag + description: No ACPI control (A=1). + + divider: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Second PLL output frequency. + + usb-host-normal: + $ref: /schemas/types.yaml#/definitions/flag + description: USB Host normal mode. + + usb-host-simulation: + $ref: /schemas/types.yaml#/definitions/flag + description: USB Host simulation mode. + + delay: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Delay time to latch read data. Set the value to 10x. + + misc-control: + type: object + description: Miscellaneous Control register values. + properties: + pad: + $ref: /schemas/types.yaml#/definitions/uint32 + description: PCI Pad drive strength. + + usbclk: + $ref: /schemas/types.yaml#/definitions/uint32 + description: USB Clcok Select. + + uart1: + $ref: /schemas/types.yaml#/definitions/flag + description: UART1 (SSP=0) + + ssp1: + $ref: /schemas/types.yaml#/definitions/flag + description: SSP1 (SSP=1) + + latch-address-disable: + $ref: /schemas/types.yaml#/definitions/flag + description: 8051 Latch disable (Lat=0). + + latch-address-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: 8051 Latch enable (Lat=1). + + panel-data-18bit: + $ref: /schemas/types.yaml#/definitions/flag + description: Flat Panel data 18bit (FP=0). + + panel-data-24bit: + $ref: /schemas/types.yaml#/definitions/flag + description: Flat Panel data 24bit (FP=1). + + xtal-freq-24mhz: + $ref: /schemas/types.yaml#/definitions/flag + description: Crystal frequency 24MHz (Freq=0). + + xtal-freq-12mhz: + $ref: /schemas/types.yaml#/definitions/flag + description: Crystal frequency 12MHz (Freq=1). + + refresh: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Internal memory refresh timing. + + hold: + $ref: /schemas/types.yaml#/definitions/uint32 + description: BUS Hold time. + + sh-ready-low: + $ref: /schemas/types.yaml#/definitions/flag + description: SuperH ready polarity active low (SH=0). + + sh-ready-high: + $ref: /schemas/types.yaml#/definitions/flag + description: SuperH ready polarity active high (SH=1). + + interrupt-normal: + $ref: /schemas/types.yaml#/definitions/flag + description: Interrupt normal (II=0). + + interrupt-inverted: + $ref: /schemas/types.yaml#/definitions/flag + description: Interrupt Inverting (II=1). + + pll-clock-count-disable: + $ref: /schemas/types.yaml#/definitions/flag + description: PLL clock count disable. + + pll-clock-count-enaable: + $ref: /schemas/types.yaml#/definitions/flag + description: PLL clock count enable. + + dac-power-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: DAC Power enable (DAC=0). + + dac-power-disable: + $ref: /schemas/types.yaml#/definitions/flag + description: DAC Power disable (DAC=1). + + usb-slave-cpu: + $ref: /schemas/types.yaml#/definitions/flag + description: USB slave controller cpu (MC=0). + + usb-slave-8051: + $ref: /schemas/types.yaml#/definitions/flag + description: USB slave controller 8051MCU (MC=1). + + burst-length-8: + $ref: /schemas/types.yaml#/definitions/flag + description: CPU Master burst length 8 (BL=0). + + burst-length-1: + $ref: /schemas/types.yaml#/definitions/flag + description: CPU Master burst length 1 (BL=1). + + usb-port-master: + $ref: /schemas/types.yaml#/definitions/flag + description: USB port master. + + usb-port-slave: + $ref: /schemas/types.yaml#/definitions/flag + description: USB port slave. + + vr-mmio-30mb: + $ref: /schemas/types.yaml#/definitions/flag + description: NEC VR Memory map MMIO locatedat 30MB (VR=0) + + vr-mmio-62mb: + $ref: /schemas/types.yaml#/definitions/flag + description: NEC VR Memory map MMIO locatedat 62MB (VR=1) + + gpio-pin-control: + type: object + description: GPIO control configuration. + properties: + pin: + type: object + properties: + gpio: + $ref: /schemas/types.yaml#/definitions/flag + description: pin in/out use GPIO. + function: + $ref: /schemas/types.yaml#/definitions/flag + description: pin in/out use function. + + gpio-i2c: + type: object + description: GPIO I2C definition. + properties: + i2c: + type: object + properties: + bus: + $ref: /schemas/types.yaml#/definitions/uint32 + description: I2C bus number. + + sda: + $ref: /schemas/types.yaml#/definitions/uint32 + description: I2C SDA pin port number. + + scl: + $ref: /schemas/types.yaml#/definitions/uint32 + description: I2C SCL pin port number. + + delay: + $ref: /schemas/types.yaml#/definitions/uint32 + description: bit transmission delay. + + timeout: + $ref: /schemas/types.yaml#/definitions/uint32 + description: transmission timeout. + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + + +examples: + # MPC5200 + - | + display@1,0 { + compatible = "smi,sm501"; + reg = <0x00000000 0x00800000 + 0x03e00000 0x00200000>; + interrupts = <1 1 3>; + mode = "640x480-32@60"; + edid = [00 ff ff ff ff ff ff 00 00 00 00 00 00 00 00 00 + 00 00 01 04 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 f0 0a 80 fb 20 e0 25 10 32 60 + 02 00 00 00 00 00 00 06 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 bd]; + };
Signature · 1 line
2.39.2
Rob Herring
maintainerRe: [RESEND v7 22/37] dt-bindings: display: smi,sm501: SMI SM501 binding json-schema
Quoted 14 lines · Yoshinori Sato
Signed-off-by Yoshinori Sato <[email protected]>--- .../bindings/display/smi,sm501.yaml | 398 ++++++++++++++++++ 1 file changed, 398 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/smi,sm501.yamlDocumentation/devicetree/bindings/display/smi,sm501.yaml new file +2
-0@@ -0,0 +1,398 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2
Documentation/devicetree/bindings/display/smi,sm501.yaml line 12
Quoted 10 lines
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +10
-0+--- +$id: http://devicetree.org/schemas/display/smi,sm501.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Silicon Motion SM501 Mobile Multimedia Companion Chip + +maintainers: + - Yoshinori Sato <[email protected]> + +description: |
Don't need '|'
Documentation/devicetree/bindings/display/smi,sm501.yaml line 13
Quoted 1 line
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +1
-0+ These DT bindings describe the SM501.
Drop "These DT bindings describe" and just describe what the h/w is.
Documentation/devicetree/bindings/display/smi,sm501.yaml line 24
Quoted 11 lines
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +11
-0+ +properties: + compatible: + const: + smi,sm501 + + reg: + maxItems: 2 + description: | + First entry: System Configuration register + Second entry: IO space (Display Controller register)
items:
- description: System Configuration register
- description: IO space (Display Controller register)
Is it just 1 register in each or should be "registers"?
Documentation/devicetree/bindings/display/smi,sm501.yaml line 34
Quoted 10 lines
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +10
-0+ + interrupts: + description: SM501 interrupt to the cpu should be described here. + + mode: + $ref: /schemas/types.yaml#/definitions/string + description: select a video mode + + edid: + description: |
Don't need '|'.
Documentation/devicetree/bindings/display/smi,sm501.yaml line 35
Quoted 1 line
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +1
-0+ verbatim EDID data block describing attached display.
s/verbatim/Verbatim/
Documentation/devicetree/bindings/display/smi,sm501.yaml line 46
Quoted 11 lines
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +11
-0+ Data from the detailed timing descriptor will be used to + program the display controller. + + little-endian: + $ref: /schemas/types.yaml#/definitions/flag + description: available on big endian systems, to set different foreign endian. + big-endian: + $ref: /schemas/types.yaml#/definitions/flag + description: available on little endian systems, to set different foreign endian. + + swap-fb-endian:
All these custom properties need vendor prefix.
But really, why are so many custom properties needed? Other display controllers don't need so many, why does this one? Do you actually have users of all of them.
Documentation/devicetree/bindings/display/smi,sm501.yaml line 58
Quoted 12 lines
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +12
-0+ $ref: /schemas/types.yaml#/definitions/flag + description: swap framebuffer byteorder. + + route-crt-panel: + $ref: /schemas/types.yaml#/definitions/flag + description: Panel output merge to CRT. + + crt: + type: object + description: CRT output control + properties: + edid:
Huh? You already defined edid elsewhere.
Quoted 16 lines
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +16
-0+ $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + verbatim EDID data block describing attached display. + Data from the detailed timing descriptor will be used to + program the display controller. + + smi,flags: + $ref: /schemas/types.yaml#/definitions/string-array + description: Display control flags. + items: + anyOf: + - const: use-init-done + - const: disable-at-exit + - const: use-hwcursor + - const: use-hwaccel + - const: panel-no-fpen
Documentation/devicetree/bindings/display/smi,sm501.yaml line 84
Quoted 10 lines
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +10
-0+ - const: panel-no-vbiasen + - const: panel-inv-fpen + - const: panel-inv-vbiasen + maxItems: 8 + + bpp: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Color depth + + panel:
Isn't this just the same as 'crt'?
Quoted 44 lines
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +44
-0+ type: object + description: Panel output control + properties: + edid: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + verbatim EDID data block describing attached display. + Data from the detailed timing descriptor will be used to + program the display controller. + + smi,flags: + $ref: /schemas/types.yaml#/definitions/string-array + description: Display control flags. + items: + anyOf: + - const: use-init-done + - const: disable-at-exit + - const: use-hwcursor + - const: use-hwaccel + - const: panel-no-fpen + - const: panel-no-vbiasen + - const: panel-inv-fpen + - const: panel-inv-vbiasen + maxItems: 8 + + bpp: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Color depth + + smi,devices: + $ref: /schemas/types.yaml#/definitions/string-array + description: Select SM501 device functions. + items: + anyOf: + - const: usb-host + - const: usb-slave + - const: ssp0 + - const: ssp1 + - const: uart0 + - const: uart1 + - const: fbaccel + - const: ac97 + - const: i2s + - const: gpio
Documentation/devicetree/bindings/display/smi,sm501.yaml line 138
Quoted 10 lines
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +10
-0+ minItems: 1 + maxItems: 10 + + smi,mclk: + $ref: /schemas/types.yaml#/definitions/uint32 + description: mclk frequency. + + smi,m1xclk: + $ref: /schemas/types.yaml#/definitions/uint32 + description: m1xclk frequency.
Clock stuff? Use the clock binding.
Quoted 111 lines
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +111
-0+ + misc-timing: + type: object + description: Miscellaneous Timing register values. + properties: + ex: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Extend bus holding time. + + xc: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Xscale clock input select. + + usb-over-current-detect-disable: + $ref: /schemas/types.yaml#/definitions/flag + description: USB host current detection disable (Us=0). + + usb-over-current-detect-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: USB host current detection disable (Us=1). + + sdram-clock-mode1-288mhz: + $ref: /schemas/types.yaml#/definitions/flag + description: SSM1 bit is clear. + + sdram-clock-mode1-div: + $ref: /schemas/types.yaml#/definitions/flag + description: SSM1 bit is set. + + sm1: + $ref: /schemas/types.yaml#/definitions/flag + description: SDRAM clock divider for PW mode 1. + + sdram-clock-mode0-288mhz: + $ref: /schemas/types.yaml#/definitions/flag + description: SSM0 bit is clear. + + sdram-clock-mode0-div: + $ref: /schemas/types.yaml#/definitions/flag + description: SSM0 bit is set. + + sm0: + $ref: /schemas/types.yaml#/definitions/uint32 + description: SDRAM clock divider for PW mode 0. + + pll-debug-input: + $ref: /schemas/types.yaml#/definitions/flag + description: 96MHz PLL debug input reference frequency (Deb=0). + + pll-debug-output: + $ref: /schemas/types.yaml#/definitions/flag + description: 96MHz PLL debug output frequency (Deb=1). + + no-acpi-control: + $ref: /schemas/types.yaml#/definitions/flag + description: No ACPI control (A=0). + + acpi-control: + $ref: /schemas/types.yaml#/definitions/flag + description: No ACPI control (A=1). + + divider: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Second PLL output frequency. + + usb-host-normal: + $ref: /schemas/types.yaml#/definitions/flag + description: USB Host normal mode. + + usb-host-simulation: + $ref: /schemas/types.yaml#/definitions/flag + description: USB Host simulation mode. + + delay: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Delay time to latch read data. Set the value to 10x. + + misc-control: + type: object + description: Miscellaneous Control register values. + properties: + pad: + $ref: /schemas/types.yaml#/definitions/uint32 + description: PCI Pad drive strength. + + usbclk: + $ref: /schemas/types.yaml#/definitions/uint32 + description: USB Clcok Select. + + uart1: + $ref: /schemas/types.yaml#/definitions/flag + description: UART1 (SSP=0) + + ssp1: + $ref: /schemas/types.yaml#/definitions/flag + description: SSP1 (SSP=1) + + latch-address-disable: + $ref: /schemas/types.yaml#/definitions/flag + description: 8051 Latch disable (Lat=0). + + latch-address-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: 8051 Latch enable (Lat=1). + + panel-data-18bit: + $ref: /schemas/types.yaml#/definitions/flag + description: Flat Panel data 18bit (FP=0). + + panel-data-24bit: + $ref: /schemas/types.yaml#/definitions/flag
Documentation/devicetree/bindings/display/smi,sm501.yaml line 258
Quoted 10 lines
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +9
-0+ description: Flat Panel data 24bit (FP=1). + + xtal-freq-24mhz: + $ref: /schemas/types.yaml#/definitions/flag + description: Crystal frequency 24MHz (Freq=0). + + xtal-freq-12mhz: + $ref: /schemas/types.yaml#/definitions/flag + description: Crystal frequency 12MHz (Freq=1).
What's the relationship between these 2 properties? What if neither is present? What if both are? Define properties such that you can't have invalid combinations. Yes, we could just handle that with constraints, but why start with a bad design. There's other cases of this same pattern here.
Quoted 71 lines
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +71
-0+ + refresh: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Internal memory refresh timing. + + hold: + $ref: /schemas/types.yaml#/definitions/uint32 + description: BUS Hold time. + + sh-ready-low: + $ref: /schemas/types.yaml#/definitions/flag + description: SuperH ready polarity active low (SH=0). + + sh-ready-high: + $ref: /schemas/types.yaml#/definitions/flag + description: SuperH ready polarity active high (SH=1). + + interrupt-normal: + $ref: /schemas/types.yaml#/definitions/flag + description: Interrupt normal (II=0). + + interrupt-inverted: + $ref: /schemas/types.yaml#/definitions/flag + description: Interrupt Inverting (II=1). + + pll-clock-count-disable: + $ref: /schemas/types.yaml#/definitions/flag + description: PLL clock count disable. + + pll-clock-count-enaable: + $ref: /schemas/types.yaml#/definitions/flag + description: PLL clock count enable. + + dac-power-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: DAC Power enable (DAC=0). + + dac-power-disable: + $ref: /schemas/types.yaml#/definitions/flag + description: DAC Power disable (DAC=1). + + usb-slave-cpu: + $ref: /schemas/types.yaml#/definitions/flag + description: USB slave controller cpu (MC=0). + + usb-slave-8051: + $ref: /schemas/types.yaml#/definitions/flag + description: USB slave controller 8051MCU (MC=1). + + burst-length-8: + $ref: /schemas/types.yaml#/definitions/flag + description: CPU Master burst length 8 (BL=0). + + burst-length-1: + $ref: /schemas/types.yaml#/definitions/flag + description: CPU Master burst length 1 (BL=1). + + usb-port-master: + $ref: /schemas/types.yaml#/definitions/flag + description: USB port master. + + usb-port-slave: + $ref: /schemas/types.yaml#/definitions/flag + description: USB port slave. + + vr-mmio-30mb: + $ref: /schemas/types.yaml#/definitions/flag + description: NEC VR Memory map MMIO locatedat 30MB (VR=0) + + vr-mmio-62mb: + $ref: /schemas/types.yaml#/definitions/flag
Documentation/devicetree/bindings/display/smi,sm501.yaml line 339
Quoted 10 lines
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +10
-0+ description: NEC VR Memory map MMIO locatedat 62MB (VR=1) + + gpio-pin-control: + type: object + description: GPIO control configuration. + properties: + pin: + type: object + properties: + gpio:
'gpio' is already in use as a property name.
Documentation/devicetree/bindings/display/smi,sm501.yaml line 344
Quoted 5 lines
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +5
-0+ $ref: /schemas/types.yaml#/definitions/flag + description: pin in/out use GPIO. + function: + $ref: /schemas/types.yaml#/definitions/flag + description: pin in/out use function.
Why do you need 2 nodes and 2 properties to define 3 possible states? There is not present, 'gpio', or 'function'. That's a single tri-state property. What does not present mean?
Documentation/devicetree/bindings/display/smi,sm501.yaml line 355
Quoted 11 lines
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +11
-0+ + gpio-i2c: + type: object + description: GPIO I2C definition. + properties: + i2c: + type: object + properties: + bus: + $ref: /schemas/types.yaml#/definitions/uint32 + description: I2C bus number.
How is bus number a property of the h/w?
Quoted 19 lines
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +19
-0+ + sda: + $ref: /schemas/types.yaml#/definitions/uint32 + description: I2C SDA pin port number. + + scl: + $ref: /schemas/types.yaml#/definitions/uint32 + description: I2C SCL pin port number. + + delay: + $ref: /schemas/types.yaml#/definitions/uint32 + description: bit transmission delay. + + timeout: + $ref: /schemas/types.yaml#/definitions/uint32 + description: transmission timeout. + +additionalProperties: false +
Documentation/devicetree/bindings/display/smi,sm501.yaml line 384
Quoted 10 lines
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +10
-0+required: + - compatible + - reg + - interrupts + + +examples: + # MPC5200 + - | + display@1,0 {
Not a correct unit address.
Documentation/devicetree/bindings/display/smi,sm501.yaml line 397
Quoted 13 lines
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +13
-0+ compatible = "smi,sm501"; + reg = <0x00000000 0x00800000 + 0x03e00000 0x00200000>; + interrupts = <1 1 3>; + mode = "640x480-32@60"; + edid = [00 ff ff ff ff ff ff 00 00 00 00 00 00 00 00 00 + 00 00 01 04 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 f0 0a 80 fb 20 e0 25 10 32 60 + 02 00 00 00 00 00 00 06 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 bd];
Kind of a sparse example. Please make examples using optional properties.
Quoted 4 lines
+ };
Signature · 1 line
2.39.2
Yoshinori Sato
maintainerPATCH RESEND v7 23/37 dt-bindings: display: sm501 register definition helper
In reply to a message not in the archiveMiscellaneous Timing and Miscellaneous Control registers definition.
--- include/dt-bindings/display/sm501.h | 76 +++++++++++++++++++++++++++++ 1 file changed, 76 insertions(+) create mode 100644 include/dt-bindings/display/sm501.h
include/dt-bindings/display/sm501.h new file +76 -0
@@ -0,0 +1,76 @@ +/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */ +#ifndef __DT_BINDING_DISPALY_SM501__ +#define __DT_BINDING_DISPALY_SM501__ + +/* Miscellaneous Conntrol */ +#define SM501_MISC_CONTROL_PAD_24 0 +#define SM501_MISC_CONTROL_PAD_12 1 +#define SM501_MISC_CONTROL_PAD_8 2 + +#define SM501_MISC_CONTROL_USBCLK_XTAL 0 +#define SM501_MISC_CONTROL_USBCLK_96MHZ 1 +#define SM501_MISC_CONTROL_USBCLK_48MHZ 2 + +#define SM501_MISC_CONTROL_RFSH_8US 0 +#define SM501_MISC_CONTROL_RFSH_16US 1 +#define SM501_MISC_CONTROL_RFSH_32US 2 +#define SM501_MISC_CONTROL_RFSH_64US 3 + +#define SM501_MISC_CONTROL_HOLD_EMPTY 0 +#define SM501_MISC_CONTROL_HOLD_8TR 1 +#define SM501_MISC_CONTROL_HOLD_16TR 2 +#define SM501_MISC_CONTROL_HOLD_24TR 3 +#define SM501_MISC_CONTROL_HOLD_32TR 4 + +/* Miscellaneous timing */ +#define SM501_MISC_TIMING_EX_HOLD_0 0 +#define SM501_MISC_TIMING_EX_HOLD_16 1 +#define SM501_MISC_TIMING_EX_HOLD_32 2 +#define SM501_MISC_TIMING_EX_HOLD_48 3 +#define SM501_MISC_TIMING_EX_HOLD_64 4 +#define SM501_MISC_TIMING_EX_HOLD_80 5 +#define SM501_MISC_TIMING_EX_HOLD_96 6 +#define SM501_MISC_TIMING_EX_HOLD_112 7 +#define SM501_MISC_TIMING_EX_HOLD_128 8 +#define SM501_MISC_TIMING_EX_HOLD_144 9 +#define SM501_MISC_TIMING_EX_HOLD_160 10 +#define SM501_MISC_TIMING_EX_HOLD_176 11 +#define SM501_MISC_TIMING_EX_HOLD_192 12 +#define SM501_MISC_TIMING_EX_HOLD_208 13 +#define SM501_MISC_TIMING_EX_HOLD_224 14 +#define SM501_MISC_TIMING_EX_HOLD_240 15 + +#define SM501_MISC_TIMING_XC_INTERNAL 0 +#define SM501_MISC_TIMING_XC_HCLK 1 +#define SM501_MISC_TIMING_XC_GPIO 2 + +#define SM501_MISC_TIMING_SM_DIV1 0 +#define SM501_MISC_TIMING_SM_DIV2 1 +#define SM501_MISC_TIMING_SM_DIV4 2 +#define SM501_MISC_TIMING_SM_DIV8 3 +#define SM501_MISC_TIMING_SM_DIV16 4 +#define SM501_MISC_TIMING_SM_DIV32 5 +#define SM501_MISC_TIMING_SM_DIV64 6 +#define SM501_MISC_TIMING_SM_DIV128 7 +#define SM501_MISC_TIMING_SM_DIV3 8 +#define SM501_MISC_TIMING_SM_DIV6 9 +#define SM501_MISC_TIMING_SM_DIV12 10 +#define SM501_MISC_TIMING_SM_DIV24 11 +#define SM501_MISC_TIMING_SM_DIV48 12 +#define SM501_MISC_TIMING_SM_DIV96 13 +#define SM501_MISC_TIMING_SM_DIV192 14 +#define SM501_MISC_TIMING_SM_DIV384 15 + +#define SM501_MISC_TIMING_DIV336MHZ 0 +#define SM501_MISC_TIMING_DIV288MHZ 1 +#define SM501_MISC_TIMING_DIV240MHZ 2 +#define SM501_MISC_TIMING_DIV192MHZ 3 + +#define SM501_MISC_TIMING_DELAY_NONE 0 +#define SM501_MISC_TIMING_DELAY_0_5 1 +#define SM501_MISC_TIMING_DELAY_1_0 2 +#define SM501_MISC_TIMING_DELAY_1_5 3 +#define SM501_MISC_TIMING_DELAY_2_0 4 +#define SM501_MISC_TIMING_DELAY_2_5 5 + +#endif
Signature · 1 line
2.39.2
Re: [RESEND v7 23/37] dt-bindings: display: sm501 register definition helper
Hi Sato-san,
Thanks for your patch!
Quoted 1 line · Yoshinori Sato
Miscellaneous Timing and Miscellaneous Control registers definition.
Please do not put raw register value definitions into DT bindings.
Quoted 12 lines
Signed-off-by Yoshinori Sato <[email protected]>include/dt-bindings/display/sm501.h new file +7
-0+/* Miscellaneous timing */ +#define SM501_MISC_TIMING_EX_HOLD_0 0 +#define SM501_MISC_TIMING_EX_HOLD_16 1 +#define SM501_MISC_TIMING_EX_HOLD_32 2 +#define SM501_MISC_TIMING_EX_HOLD_48 3 +#define SM501_MISC_TIMING_EX_HOLD_64 4 +#define SM501_MISC_TIMING_EX_HOLD_80 5
include/dt-bindings/display/sm501.h line 41
Quoted 10 lines
include/dt-bindings/display/sm501.h new file +10
-0+#define SM501_MISC_TIMING_EX_HOLD_96 6 +#define SM501_MISC_TIMING_EX_HOLD_112 7 +#define SM501_MISC_TIMING_EX_HOLD_128 8 +#define SM501_MISC_TIMING_EX_HOLD_144 9 +#define SM501_MISC_TIMING_EX_HOLD_160 10 +#define SM501_MISC_TIMING_EX_HOLD_176 11 +#define SM501_MISC_TIMING_EX_HOLD_192 12 +#define SM501_MISC_TIMING_EX_HOLD_208 13 +#define SM501_MISC_TIMING_EX_HOLD_224 14 +#define SM501_MISC_TIMING_EX_HOLD_240 15
E.g. these are used by the (not very descriptive) "ex" property:
ex:
$ref: /schemas/types.yaml#/definitions/uint32
description: Extend bus holding time.
Please instead use an enum for the actual holding time ([ 0, 16, 32, ...]) in the DT bindings, and convert from actual holding time to register value in the driver.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]
In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
Yoshinori Sato
maintainerPATCH RESEND v7 24/37 mfd: sm501: Convert platform_data to OF property
In reply to a message not in the archiveVarious parameters of SM501 can be set using platform_data, so parameters cannot be passed in the DeviceTree target. Expands the parameters set in platform_data so that they can be specified using DeviceTree properties.
--- drivers/mfd/sm501.c | 315 ++++++++++++++++++++++++++++++++++ drivers/video/fbdev/sm501fb.c | 106 ++++++++++++ 2 files changed, 421 insertions(+)
drivers/mfd/sm501.c +315 -0
@@ -82,6 +82,16 @@ struct sm501_devdata {unsigned int rev; }; +struct sm501_config_props_uint { +char *name; +u32 shift; +}; + +struct sm501_config_props_flag { +char *clr_name; +char *set_name; +u32 bit; +};#define MHZ (1000 * 1000)
@@ -1370,6 +1380,305 @@ static int sm501_init_dev(struct sm501_devdata *sm)return 0 ; } +static const struct sm501_config_props_uint misc_timing[] = { + {"delay" ,0 }, + {"-" ,3 }, + {"divider" ,4 }, + {"-" ,6 }, + {"sm0" ,8 }, + {"-" ,12 }, + {"sm1" ,16 }, + {"-" ,20 }, + {"xc" ,24 }, + {"-" ,26 }, + {"ex" ,28 }, + {NULL ,32 }, +}; + +static const struct sm501_config_props_flag misc_timing_flag[] = { + {"usb-host-normal" ,"usb-host-simulation" ,3 }, + {"no-acpi-control" ,"acpi-control" ,6 }, + {"pll-debug-input" ,"pll-debug-output" ,7 }, + {"sdram-clock-mode0-288mhz" ,"sdram-clock-mode0-div" ,12 }, + {"sdram-clock-mode1-288mhz" ,"sdram-clock-mode1-div" ,20 }, + {"usb-over-current-detect-disable" , +"usb-over-current-detect-enable" ,23 }, + {}, +}; + +static const struct sm501_config_props_uint misc_control[] = { + {"hold" ,18 }, + {"refresh" ,21 }, + {"-" ,23 }, + {"usbclk" ,28 }, + {"pad" ,30 }, + {NULL ,32 }, +}; + +static const struct sm501_config_props_flag misc_control_flag[] = { + {"vr-mmio-30mb" ,"vr-mmio-62mb" ,4 }, + {"usb-port-master" ,"usb-port-slave" ,9 }, + {"burst-length-8" ,"burst-length-1" ,10 }, + {"usb-slave-cpu" ,"usb-slave-8051" ,11 }, + {"dac-power-enable" ,"dac-power-disable" ,12 }, + {"pll-clock-count-disable" ,"pll-clock-count-enable" ,15 }, + {"interrupt-normal" ,"interrupt-invarted" ,16 }, + {"sh-ready-low" ,"sh-ready-high" ,17 }, + {"xtal-freq-24mhz" ,"xtal-freq-12mhz" ,24 }, + {"panel-data-18bit" ,"panel-dtat-24bit" ,25 }, + {"latch-address-disable" ,"latch-address-enable" ,26 }, + {"uart1" ,"ssp1" ,27 }, + {}, +}; + +/* Read configuration values */ +static void sm501_of_read_config (struct device *dev,struct device_node *np, +const char *prefix, +const struct sm501_config_props_uint *props, +const struct sm501_config_props_flag *props_flag, +struct sm501_reg_init *ret) +{ +struct device_node *child; +char *name; +u32 shift; +u32 width; +u32 mask; +u32 val; + + ret->mask = ~0 ; + ret->set =0 ; + + child =of_get_child_by_name (np, prefix); +if (!child) +return ; + +while (props->name) { + name = props->name; + shift = props->shift; + props++; + +if (name[0 ] =='-' || +of_property_read_u32 (child, name, &val)) +continue ; + + width = props->shift - shift; + mask = (1 << width) -1 ; +if (mask < val) { +dev_warn (dev,"%s invalid value %d" , name, val); +continue ; + } + mask = ~(mask << shift); + ret->mask &= mask; + ret->set |= val << shift; + } +while (props_flag->clr_name) { + val = ~0 ; +if (of_property_read_bool (child, props_flag->clr_name)) + val =0 ; +else if (of_property_read_bool (child, props_flag->set_name)) + val =1 ; +if (val != ~0 ) { + val <<= (props_flag->bit &31 ); + mask =1 << (props_flag->bit &31 ); + ret->mask &= ~mask; + ret->set |= val; + } + props_flag++; + } +} + +/* Read GPIO control */ +/* +* DT example. +* gpio-pin-control { +* pin@0 { +* gpio-port; +* }; +* pin@1 { +* function; +* }; +* }; +*/ +static void sm501_of_read_gpio (struct device *dev,struct device_node *np, +struct sm501_reg_init *hi,struct sm501_reg_init *low) +{ +struct device_node *gpio_group, *pin; +const char *prop_mode; +unsigned int pin_no; +int mode; +u64 mask; +u64 set; + + mask = ~0 ; + set =0 ; + gpio_group =of_get_child_by_name (np,"gpio-pin-control" ); +if (gpio_group) { +for_each_child_of_node (gpio_group, pin) { + mode =-1 ; +if (sscanf (pin->full_name,"pin@%u" , &pin_no) ==1 ) { +if (of_property_read_bool (pin,"gpio-port" )) + mode =0 ; +else if (of_property_read_bool (pin,"function" )) + mode =1 ; + } +/* GPIO0 - 47 and 55 -63 */ +if (mode <0 || + (pin_no >=64 || (pin_no >=48 && pin_no <=54 ))) { +dev_warn (dev, +"%s mode %s is invalid." , pin->name, prop_mode); + }else { + mask &= ~(1 << pin_no); + set |= mode << pin_no; + } + } + } + hi->set = set >>32 ; + low->set = set &0xffffffff ; + hi->mask = mask >>32 ; + low->mask = mask &0xffffffff ; +} + +static inline int read_i2c_prop (struct device *dev,struct device_node *child, +const char *name,u32 *val) +{ +if (of_property_read_u32 (child, name, val)) { +dev_warn (dev,"%s/%s not found. skip it." ,of_node_full_name (child), name); +return -ENOENT ; + } +return 0 ; +} + +/* Read GPIO I2C configuration */ +/* +* DT example. +* gpio-i2c { +* i2c@0 { +* sda = <gpio-pin>; +* scl = <gpio-pin>; +* delay = <delay>; +* timeout = <timeout>; +* }; +* i2c@1 { +* : +* }; +* : +* }; +*/ +static int sm501_parse_dt_gpio_i2c (struct device *dev,struct sm501_platdata *plat, +struct device_node *np) +{ +struct device_node *i2c_group, *child; +unsigned int i; +u32 i2c_nr; +int err; + + i2c_group =of_get_child_by_name (np,"gpio-i2c" ); +if (!i2c_group) +return 0 ; + + i2c_nr =of_get_child_count (i2c_group); + plat->gpio_i2c =devm_kzalloc (dev,sizeof (*plat->gpio_i2c) * i2c_nr, +GFP_KERNEL ); +if (!plat->gpio_i2c) +return -ENOMEM ; + + plat->gpio_i2c_nr = i2c_nr; + i =0 ; +for_each_child_of_node (i2c_group, child) { +u32 bus; + +if (sscanf (child->full_name,"i2c@%u" , &bus) !=1 ) { +dev_warn (dev,"Unknown address %s\n" , child->name); +continue ; + } + + err =0 ; + plat->gpio_i2c[i].bus_num = bus; + err +=read_i2c_prop (dev, child,"sda" , &plat->gpio_i2c[i].pin_sda); + err +=read_i2c_prop (dev, child,"scl" , &plat->gpio_i2c[i].pin_scl); + err +=read_i2c_prop (dev, child,"delay" , &plat->gpio_i2c[i].udelay); + err +=read_i2c_prop (dev, child,"timeout" , &plat->gpio_i2c[i].timeout); +if (err ==0 ) + i++; + } + +return 0 ; +} + +/* Read device functions */ +static u32 sm501_read_devices (struct device *dev,struct device_node *np) +{ +static const char *const funcname[] = { +"usb-host" ,"usb-slave" ,"ssp0" ,"ssp1" , +"uart0" ,"uart1" ,"fbaccel" ,"ac97" , +"i2s" ,"gpio" , + }; +struct property *prop; +unsigned int i; +const char *s; +u32 ret =0 ; + +of_property_for_each_string (np,"smi,devices" , prop, s) { +for (i =0 ; i <ARRAY_SIZE (funcname); i++) { +if (strcmp (s, funcname[i]) ==0 ) { + ret |=1 << i; + goto next; + } + } +dev_warn (dev,"Unknown device function '%s'" , s); +next: + } +if (!ret) +dev_warn (dev,"devices not defined. disable all functions." ); +return ret; +} + +/* Build platform_data from OF property */ +struct plat_dt { +struct sm501_platdata plat; +struct sm501_initdata init; +}; + +static int sm501_parse_dt (struct sm501_devdata *sm,struct device_node *np) +{ +struct sm501_platdata *plat; +struct plat_dt *dt_p; +u32 word; +int ret; + + dt_p =devm_kzalloc (sm->dev,sizeof (*dt_p),GFP_KERNEL ); +if (!dt_p) +return -ENOMEM ; + + plat = &dt_p->plat; + plat->init = &dt_p->init; + + plat->init->devices =sm501_read_devices (sm->dev, np); +/* mclk and m1xclk are not u32, so convert between them using intermediate variables. */ +of_property_read_u32 (np,"smi,mclk" , &word); + plat->init->mclk = word; +of_property_read_u32 (np,"smi,m1xclk" , &word); + plat->init->m1xclk = word; + +sm501_of_read_config (sm->dev, np,"misc-timing" , + misc_timing, misc_timing_flag, + &plat->init->misc_timing); +sm501_of_read_config (sm->dev, np,"misc-control" , + misc_control, misc_control_flag, + &plat->init->misc_control); +sm501_of_read_gpio (sm->dev, np, + &plat->init->gpio_high, &plat->init->gpio_low); + +if (IS_ENABLED (CONFIG_MFD_SM501_GPIO ) && + (plat->init->devices &SM501_USE_GPIO )) { + ret =sm501_parse_dt_gpio_i2c (sm->dev, plat, np); +if (ret) +return ret; + } + sm->platdata = plat; +return 0 ; +} +static int sm501_plat_probe (struct platform_device *dev) {struct sm501_devdata *sm;
@@ -1406,6 +1715,12 @@ static int sm501_plat_probe(struct platform_device *dev) goto err_res; } +if (IS_ENABLED (CONFIG_OF ) && dev->dev.of_node) { + ret =sm501_parse_dt (sm, dev->dev.of_node); +if (ret) + goto err_res; + } +platform_set_drvdata (dev, sm); sm->regs =ioremap (sm->io_res->start,resource_size (sm->io_res));
drivers/video/fbdev/sm501fb.c +106 -0
118 lines not on this page · raw message
Signature · 1 line
2.39.2
Lee Jones
maintainerRe: [RESEND v7 24/37] mfd: sm501: Convert platform_data to OF property
Quoted 10 lines · Yoshinori Sato
Various parameters of SM501 can be set using
platform_data, so parameters cannot be passed in the DeviceTree target. Expands the parameters set inplatform_dataso that they can be specified using DeviceTree properties.Signed-off-by Yoshinori Sato <[email protected]>--- drivers/mfd/sm501.c | 315 ++++++++++++++++++++++++++++++++++ drivers/video/fbdev/sm501fb.c | 106 ++++++++++++ 2 files changed, 421 insertions(+)
I don't know exactly what this is, but I do know that I don't like it.
If you manage to get it through another maintainer, more power to you, but it is not suitable for MFD.
Quoted 467 lines
drivers/mfd/sm501.c +315
-0@@ -82,6 +82,16 @@ struct sm501_devdata {unsigned int rev; }; +struct sm501_config_props_uint { +char *name; +u32 shift; +}; + +struct sm501_config_props_flag { +char *clr_name; +char *set_name; +u32 bit; +};#define MHZ (1000 * 1000)@@ -1370,6 +1380,305 @@ static int sm501_init_dev(struct sm501_devdata *sm)return 0 ; } +static const struct sm501_config_props_uint misc_timing[] = { + {"delay" ,0 }, + {"-" ,3 }, + {"divider" ,4 }, + {"-" ,6 }, + {"sm0" ,8 }, + {"-" ,12 }, + {"sm1" ,16 }, + {"-" ,20 }, + {"xc" ,24 }, + {"-" ,26 }, + {"ex" ,28 }, + {NULL ,32 }, +}; + +static const struct sm501_config_props_flag misc_timing_flag[] = { + {"usb-host-normal" ,"usb-host-simulation" ,3 }, + {"no-acpi-control" ,"acpi-control" ,6 }, + {"pll-debug-input" ,"pll-debug-output" ,7 }, + {"sdram-clock-mode0-288mhz" ,"sdram-clock-mode0-div" ,12 }, + {"sdram-clock-mode1-288mhz" ,"sdram-clock-mode1-div" ,20 }, + {"usb-over-current-detect-disable" , +"usb-over-current-detect-enable" ,23 }, + {}, +}; + +static const struct sm501_config_props_uint misc_control[] = { + {"hold" ,18 }, + {"refresh" ,21 }, + {"-" ,23 }, + {"usbclk" ,28 }, + {"pad" ,30 }, + {NULL ,32 }, +}; + +static const struct sm501_config_props_flag misc_control_flag[] = { + {"vr-mmio-30mb" ,"vr-mmio-62mb" ,4 }, + {"usb-port-master" ,"usb-port-slave" ,9 }, + {"burst-length-8" ,"burst-length-1" ,10 }, + {"usb-slave-cpu" ,"usb-slave-8051" ,11 }, + {"dac-power-enable" ,"dac-power-disable" ,12 }, + {"pll-clock-count-disable" ,"pll-clock-count-enable" ,15 }, + {"interrupt-normal" ,"interrupt-invarted" ,16 }, + {"sh-ready-low" ,"sh-ready-high" ,17 }, + {"xtal-freq-24mhz" ,"xtal-freq-12mhz" ,24 }, + {"panel-data-18bit" ,"panel-dtat-24bit" ,25 }, + {"latch-address-disable" ,"latch-address-enable" ,26 }, + {"uart1" ,"ssp1" ,27 }, + {}, +}; + +/* Read configuration values */ +static void sm501_of_read_config (struct device *dev,struct device_node *np, +const char *prefix, +const struct sm501_config_props_uint *props, +const struct sm501_config_props_flag *props_flag, +struct sm501_reg_init *ret) +{ +struct device_node *child; +char *name; +u32 shift; +u32 width; +u32 mask; +u32 val; + + ret->mask = ~0 ; + ret->set =0 ; + + child =of_get_child_by_name (np, prefix); +if (!child) +return ; + +while (props->name) { + name = props->name; + shift = props->shift; + props++; + +if (name[0 ] =='-' || +of_property_read_u32 (child, name, &val)) +continue ; + + width = props->shift - shift; + mask = (1 << width) -1 ; +if (mask < val) { +dev_warn (dev,"%s invalid value %d" , name, val); +continue ; + } + mask = ~(mask << shift); + ret->mask &= mask; + ret->set |= val << shift; + } +while (props_flag->clr_name) { + val = ~0 ; +if (of_property_read_bool (child, props_flag->clr_name)) + val =0 ; +else if (of_property_read_bool (child, props_flag->set_name)) + val =1 ; +if (val != ~0 ) { + val <<= (props_flag->bit &31 ); + mask =1 << (props_flag->bit &31 ); + ret->mask &= ~mask; + ret->set |= val; + } + props_flag++; + } +} + +/* Read GPIO control */ +/* +* DT example. +* gpio-pin-control { +* pin@0 { +* gpio-port; +* }; +* pin@1 { +* function; +* }; +* }; +*/ +static void sm501_of_read_gpio (struct device *dev,struct device_node *np, +struct sm501_reg_init *hi,struct sm501_reg_init *low) +{ +struct device_node *gpio_group, *pin; +const char *prop_mode; +unsigned int pin_no; +int mode; +u64 mask; +u64 set; + + mask = ~0 ; + set =0 ; + gpio_group =of_get_child_by_name (np,"gpio-pin-control" ); +if (gpio_group) { +for_each_child_of_node (gpio_group, pin) { + mode =-1 ; +if (sscanf (pin->full_name,"pin@%u" , &pin_no) ==1 ) { +if (of_property_read_bool (pin,"gpio-port" )) + mode =0 ; +else if (of_property_read_bool (pin,"function" )) + mode =1 ; + } +/* GPIO0 - 47 and 55 -63 */ +if (mode <0 || + (pin_no >=64 || (pin_no >=48 && pin_no <=54 ))) { +dev_warn (dev, +"%s mode %s is invalid." , pin->name, prop_mode); + }else { + mask &= ~(1 << pin_no); + set |= mode << pin_no; + } + } + } + hi->set = set >>32 ; + low->set = set &0xffffffff ; + hi->mask = mask >>32 ; + low->mask = mask &0xffffffff ; +} + +static inline int read_i2c_prop (struct device *dev,struct device_node *child, +const char *name,u32 *val) +{ +if (of_property_read_u32 (child, name, val)) { +dev_warn (dev,"%s/%s not found. skip it." ,of_node_full_name (child), name); +return -ENOENT ; + } +return 0 ; +} + +/* Read GPIO I2C configuration */ +/* +* DT example. +* gpio-i2c { +* i2c@0 { +* sda = <gpio-pin>; +* scl = <gpio-pin>; +* delay = <delay>; +* timeout = <timeout>; +* }; +* i2c@1 { +* : +* }; +* : +* }; +*/ +static int sm501_parse_dt_gpio_i2c (struct device *dev,struct sm501_platdata *plat, +struct device_node *np) +{ +struct device_node *i2c_group, *child; +unsigned int i; +u32 i2c_nr; +int err; + + i2c_group =of_get_child_by_name (np,"gpio-i2c" ); +if (!i2c_group) +return 0 ; + + i2c_nr =of_get_child_count (i2c_group); + plat->gpio_i2c =devm_kzalloc (dev,sizeof (*plat->gpio_i2c) * i2c_nr, +GFP_KERNEL ); +if (!plat->gpio_i2c) +return -ENOMEM ; + + plat->gpio_i2c_nr = i2c_nr; + i =0 ; +for_each_child_of_node (i2c_group, child) { +u32 bus; + +if (sscanf (child->full_name,"i2c@%u" , &bus) !=1 ) { +dev_warn (dev,"Unknown address %s\n" , child->name); +continue ; + } + + err =0 ; + plat->gpio_i2c[i].bus_num = bus; + err +=read_i2c_prop (dev, child,"sda" , &plat->gpio_i2c[i].pin_sda); + err +=read_i2c_prop (dev, child,"scl" , &plat->gpio_i2c[i].pin_scl); + err +=read_i2c_prop (dev, child,"delay" , &plat->gpio_i2c[i].udelay); + err +=read_i2c_prop (dev, child,"timeout" , &plat->gpio_i2c[i].timeout); +if (err ==0 ) + i++; + } + +return 0 ; +} + +/* Read device functions */ +static u32 sm501_read_devices (struct device *dev,struct device_node *np) +{ +static const char *const funcname[] = { +"usb-host" ,"usb-slave" ,"ssp0" ,"ssp1" , +"uart0" ,"uart1" ,"fbaccel" ,"ac97" , +"i2s" ,"gpio" , + }; +struct property *prop; +unsigned int i; +const char *s; +u32 ret =0 ; + +of_property_for_each_string (np,"smi,devices" , prop, s) { +for (i =0 ; i <ARRAY_SIZE (funcname); i++) { +if (strcmp (s, funcname[i]) ==0 ) { + ret |=1 << i; + goto next; + } + } +dev_warn (dev,"Unknown device function '%s'" , s); +next: + } +if (!ret) +dev_warn (dev,"devices not defined. disable all functions." ); +return ret; +} + +/* Build platform_data from OF property */ +struct plat_dt { +struct sm501_platdata plat; +struct sm501_initdata init; +}; + +static int sm501_parse_dt (struct sm501_devdata *sm,struct device_node *np) +{ +struct sm501_platdata *plat; +struct plat_dt *dt_p; +u32 word; +int ret; + + dt_p =devm_kzalloc (sm->dev,sizeof (*dt_p),GFP_KERNEL ); +if (!dt_p) +return -ENOMEM ; + + plat = &dt_p->plat; + plat->init = &dt_p->init; + + plat->init->devices =sm501_read_devices (sm->dev, np); +/* mclk and m1xclk are not u32, so convert between them using intermediate variables. */ +of_property_read_u32 (np,"smi,mclk" , &word); + plat->init->mclk = word; +of_property_read_u32 (np,"smi,m1xclk" , &word); + plat->init->m1xclk = word; + +sm501_of_read_config (sm->dev, np,"misc-timing" , + misc_timing, misc_timing_flag, + &plat->init->misc_timing); +sm501_of_read_config (sm->dev, np,"misc-control" , + misc_control, misc_control_flag, + &plat->init->misc_control); +sm501_of_read_gpio (sm->dev, np, + &plat->init->gpio_high, &plat->init->gpio_low); + +if (IS_ENABLED (CONFIG_MFD_SM501_GPIO ) && + (plat->init->devices &SM501_USE_GPIO )) { + ret =sm501_parse_dt_gpio_i2c (sm->dev, plat, np); +if (ret) +return ret; + } + sm->platdata = plat; +return 0 ; +} +static int sm501_plat_probe (struct platform_device *dev) {struct sm501_devdata *sm;@@ -1406,6 +1715,12 @@ static int sm501_plat_probe(struct platform_device *dev) goto err_res; } +if (IS_ENABLED (CONFIG_OF ) && dev->dev.of_node) { + ret =sm501_parse_dt (sm, dev->dev.of_node); +if (ret) + goto err_res; + } +platform_set_drvdata (dev, sm); sm->regs =ioremap (sm->io_res->start,resource_size (sm->io_res));drivers/video/fbdev/sm501fb.c +106
-0@@ -1932,6 +1932,106 @@ static int sm501fb_start_one(struct sm501fb_info *info,return 0 ; } +#if defined(CONFIG_OF ) +static u32 read_display_flags (struct device_node *np) +{ +static const char *const name[] = { +"use-init-done" ,"disable-at-exit" ,"use-hwcursor" ,"use-hwaccel" , +"panel-no-fpen" ,"panel-no-vbiasen" ,"panel-inv-fpen" ,"panel-inv-vbiasen" , + }; + +struct property *prop; +unsigned int i; +const char *s; +u32 ret =0 ; + +of_property_for_each_string (np,"smi,flags" , prop, s) { +for (i =0 ; i <ARRAY_SIZE (name); i++) { +if (strcmp (s, name[i]) ==0 ) { + ret |=1 << i; +break ; + } + } + } +return ret; +} + +/* parse CRT / panel configuration */ +static struct sm501_platdata_fbsub *dt_fbsub (struct device *dev, +struct device_node *np, +const char *name) +{ +struct sm501_platdata_fbsub *fbsub =NULL ; +struct fb_videomode *def_mode =NULL ; +struct device_node *child; +const void *p_edid; +u32 flags =0 ; +u32 bpp =0 ; +int len; + + child =of_get_child_by_name (np, name); +if (child ==NULL ) +return NULL ; + + p_edid =of_get_property (child,"edid" , &len); +if (p_edid && len ==EDID_LENGTH ) { +struct fb_monspecs *specs; +u8 *edid; + + edid =kmemdup (p_edid,EDID_LENGTH ,GFP_KERNEL ); +if (edid) { + specs =kzalloc (sizeof (*specs),GFP_KERNEL ); +if (specs) { +fb_edid_to_monspecs (edid, specs); + def_mode = specs->modedb; + } + } +kfree (edid); + } + +of_property_read_u32 (child,"bpp" , &bpp); + +/* If flags property is obtained, fbsub is returned. */ + flags =read_display_flags (child); +if (flags) { + fbsub =devm_kzalloc (dev,sizeof (*fbsub),GFP_KERNEL ); +if (fbsub) { + fbsub->def_mode = def_mode; + fbsub->def_bpp = bpp; + fbsub->flags = flags; + } + } +return fbsub; +} + +/* Build platform_data from OF property */ +static struct sm501_platdata_fb *pdata_from_dt (struct device *dev,struct device_node *np) +{ +enum sm501_fb_routing fb_route =SM501_FB_OWN ; +struct sm501_platdata_fb *pdata =NULL ; +struct sm501_platdata_fbsub *fb_crt; +struct sm501_platdata_fbsub *fb_pnl; +unsigned int flags =0 ; + +if (of_property_read_bool (np,"route-crt-panel" )) + fb_route =SM501_FB_CRT_PANEL ; +if (of_property_read_bool (np,"swap-fb-endian" )) + flags =SM501_FBPD_SWAP_FB_ENDIAN ; + fb_crt =dt_fbsub (dev, np,"crt" ); + fb_pnl =dt_fbsub (dev, np,"panel" ); +if (fb_crt || fb_pnl) { + pdata =devm_kzalloc (dev,sizeof (*pdata),GFP_KERNEL ); +if (pdata) { + pdata->fb_route = fb_route; + pdata->flags = flags; + pdata->fb_crt = fb_crt; + pdata->fb_pnl = fb_pnl; + } + } +return pdata; +} +#endif +static int sm501fb_probe (struct platform_device *pdev) {struct sm501fb_info *info;@@ -1974,6 +2074,12 @@ static int sm501fb_probe(struct platform_device *pdev)if (info->edid_data) found = 1; } +/* Get platform data compatible configuration */ +if (!found) { + info->pdata =pdata_from_dt (dev, np); +if (info->pdata) + found =1 ; + } }#endif if (!found) {Signature · 1 line
2.39.2
Signature · 1 line
Lee Jones [李琼斯]
Yoshinori Sato
maintainerPATCH RESEND v7 25/37 dt-binding: sh: cpus: Add SH CPUs json-schema
In reply to a message not in the archiveRenesas SH series and compatible ISA CPUs.
--- .../devicetree/bindings/sh/cpus.yaml | 63 +++++++++++++++++++ 1 file changed, 63 insertions(+) create mode 100644 Documentation/devicetree/bindings/sh/cpus.yaml
Documentation/devicetree/bindings/sh/cpus.yaml new file +63 -0
@@ -0,0 +1,63 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sh/cpus.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas SuperH CPUs + +maintainers: + - Yoshinori Sato <[email protected]> + +description: |+ + Definition of CPU core with Renesas SuperH and compatible instruction set. + +properties: + compatible: + anyOf: + - items: + - enum: + - renesas,sh2a + - renesas,sh3 + - renesas,sh4 + - renesas,sh4a + - jcore,j2 + - const: renesas,sh2 + - const: renesas,sh2 + + clocks: + maxItems: 1 + + reg: + maxItems: 1 + + device_type: + const: cpu + +required: + - compatible + - reg + - device_type + +additionalProperties: true + +examples: + - | + #include <dt-bindings/clock/sh7750-cpg.h> + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu: cpu@0 { + compatible = "renesas,sh4", "renesas,sh2"; + device_type = "cpu"; + reg = <0>; + clocks = <&cpg SH7750_CPG_ICK>; + clock-names = "ick"; + icache-size = <16384>; + icache-line-size = <32>; + dcache-size = <32768>; + dcache-line-size = <32>; + }; + }; +...
Signature · 1 line
2.39.2
Rob Herring
maintainerRe: [RESEND v7 25/37] dt-binding: sh: cpus: Add SH CPUs json-schema
Quoted 21 lines · Yoshinori Sato
Renesas SH series and compatible ISA CPUs.
Signed-off-by Yoshinori Sato <[email protected]>--- .../devicetree/bindings/sh/cpus.yaml | 63 +++++++++++++++++++ 1 file changed, 63 insertions(+) create mode 100644 Documentation/devicetree/bindings/sh/cpus.yamlDocumentation/devicetree/bindings/sh/cpus.yaml new file +7
-0@@ -0,0 +1,63 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sh/cpus.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas SuperH CPUs
Documentation/devicetree/bindings/sh/cpus.yaml line 17
Quoted 10 lines
Documentation/devicetree/bindings/sh/cpus.yaml new file +10
-0+ +maintainers: + - Yoshinori Sato <[email protected]> + +description: |+ + Definition of CPU core with Renesas SuperH and compatible instruction set. + +properties: + compatible: + anyOf:
oneOf
Quoted 15 lines
Documentation/devicetree/bindings/sh/cpus.yaml new file +15
-0+ - items: + - enum: + - renesas,sh2a + - renesas,sh3 + - renesas,sh4 + - renesas,sh4a + - jcore,j2 + - const: renesas,sh2 + - const: renesas,sh2 + + clocks: + maxItems: 1 + + reg: + maxItems: 1
Documentation/devicetree/bindings/sh/cpus.yaml line 42
Quoted 10 lines
Documentation/devicetree/bindings/sh/cpus.yaml new file +10
-0+ + device_type: + const: cpu + +required: + - compatible + - reg + - device_type + +additionalProperties: true
This is a problem with the other cpu bindings, but should not be copied here. Add a $ref to schemas/cpu.yaml and make this 'unevaluatedProperties: false'.
Quoted 24 lines
Documentation/devicetree/bindings/sh/cpus.yaml new file +21
-0+ +examples: + - | + #include <dt-bindings/clock/sh7750-cpg.h> + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu: cpu@0 { + compatible = "renesas,sh4", "renesas,sh2"; + device_type = "cpu"; + reg = <0>; + clocks = <&cpg SH7750_CPG_ICK>; + clock-names = "ick"; + icache-size = <16384>; + icache-line-size = <32>; + dcache-size = <32768>; + dcache-line-size = <32>; + }; + }; +...Signature · 1 line
2.39.2
Yoshinori Sato
maintainerPATCH RESEND v7 26/37 dt-bindings: vendor-prefixes: Add iodata
In reply to a message not in the archiveAdd IO DATA DEVICE INC.
https://www.iodata.com/
--- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/vendor-prefixes.yaml +2 -0
@@ -708,6 +708,8 @@ patternProperties: description: Inventec "^inversepath,.*": description: Inverse Path + "^iodata,.*": + description: IO DATA DEVICE Inc. "^iom,.*": description: Iomega Corporation "^irondevice,.*":
Signature · 1 line
2.39.2
Re: [RESEND v7 26/37] dt-bindings: vendor-prefixes: Add iodata
Quoted 9 lines · Yoshinori Sato
Add IO DATA DEVICE INC.
https://www.iodata.com/Signed-off-by Yoshinori Sato <[email protected]>Reviewed-by Geert Uytterhoeven <[email protected]>--- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+)
This is a friendly reminder during the review process.
It looks like you received a tag and forgot to add it.
If you do not know the process, here is a short explanation:
Please add Acked-by/Reviewed-by/Tested-by tags when posting new versions, under or above your Signed-off-by tag. Tag is "received", when provided in a message replied to you on the mailing list. Tools like b4 can help here. However, there's no need to repost patches *only* to add the tags. The upstream maintainer will do that for tags received on the version they apply.
https://elixir.bootlin.com/linux/v6.5-rc3/source/Documentation/process/submitting-patches.rst#L577
If a tag was not added on purpose, please state why and what changed.
Best regards,
Krzysztof
Yoshinori Sato
maintainerPATCH RESEND v7 27/37 dt-bindings: ata: ata-generic: Add new targets
In reply to a message not in the archiveAdded new ata-generic target.
- iodata,usl-5p-ata
- renesas,rts7751r2d-ata
Each boards have simple IDE Interface. Use ATA generic driver.
--- Documentation/devicetree/bindings/ata/ata-generic.yaml | 2 ++ 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/ata/ata-generic.yaml +2 -0
@@ -18,6 +18,8 @@ properties: - enum: - arm,vexpress-cf - fsl,mpc8349emitx-pata + - iodata,usl-5p-ata + - renesas,rts7751r2d-ata - const: ata-generic reg:
Signature · 1 line
2.39.2
Re: [RESEND v7 27/37] dt-bindings: ata: ata-generic: Add new targets
Quoted 6 lines · Yoshinori Sato
Added new ata-generic target.
- iodata,usl-5p-ata
- renesas,rts7751r2d-ataEach boards have simple IDE Interface. Use ATA generic driver.
This is a friendly reminder during the review process.
It looks like you received a tag and forgot to add it.
If you do not know the process, here is a short explanation:
Please add Acked-by/Reviewed-by/Tested-by tags when posting new versions, under or above your Signed-off-by tag. Tag is "received", when provided in a message replied to you on the mailing list. Tools like b4 can help here. However, there's no need to repost patches *only* to add the tags. The upstream maintainer will do that for tags received on the version they apply.
https://elixir.bootlin.com/linux/v6.5-rc3/source/Documentation/process/submitting-patches.rst#L577
If a tag was not added on purpose, please state why and what changed.
Best regards,
Krzysztof
Yoshinori Sato
maintainerPATCH RESEND v7 28/37 dt-bindings: soc: renesas: sh: Add SH7751 based target
In reply to a message not in the archive--- .../devicetree/bindings/soc/renesas/sh.yaml | 27 +++++++++++++++++++ 1 file changed, 27 insertions(+) create mode 100644 Documentation/devicetree/bindings/soc/renesas/sh.yaml
Documentation/devicetree/bindings/soc/renesas/sh.yaml new file +27 -0
@@ -0,0 +1,27 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/soc/renesas/sh.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas SuperH Platform + +maintainers: + - Yoshinori Sato <[email protected]> + +properties: + $nodename: + const: '/' + compatible: + oneOf: + - description: SH7751R based platform + items: + - enum: + - renesas,rts7751r2d # Renesas SH4 2D graphics board + - iodata,landisk # LANDISK HDL-U + - iodata,usl-5p # USL-5P + - const: renesas,sh7751r + +additionalProperties: true + +...
Signature · 1 line
2.39.2
Re: [RESEND v7 28/37] dt-bindings: soc: renesas: sh: Add SH7751 based target
Hi Sato-san,
Quoted 1 line · Yoshinori Sato
Signed-off-by Yoshinori Sato <[email protected]>
Thanks for the update!
Documentation/devicetree/bindings/soc/renesas/sh.yaml line 16
Quoted 5 lines
Documentation/devicetree/bindings/soc/renesas/sh.yaml new file +2
-0+ compatible: + oneOf:
As adding more SoCs is expected, having oneOf from the start is fine.
Documentation/devicetree/bindings/soc/renesas/sh.yaml line 23
Quoted 7 lines
Documentation/devicetree/bindings/soc/renesas/sh.yaml new file +7
-0+ - description: SH7751R based platform + items: + - enum: + - renesas,rts7751r2d # Renesas SH4 2D graphics board + - iodata,landisk # LANDISK HDL-U + - iodata,usl-5p # USL-5P + - const: renesas,sh7751r
Gr{oetje,eeting}s,
Geert
Signature · 5 lines
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected] In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds
Re: [RESEND v7 28/37] dt-bindings: soc: renesas: sh: Add SH7751 based target
In reply to Yoshinori SatoQuoted 6 lines · Yoshinori Sato
Signed-off-by Yoshinori Sato <[email protected]>--- .../devicetree/bindings/soc/renesas/sh.yaml | 27 +++++++++++++++++++ 1 file changed, 27 insertions(+) create mode 100644 Documentation/devicetree/bindings/soc/renesas/sh.yaml
Yoshinori Sato
maintainerPATCH RESEND v7 29/37 sh: SH7751R SoC Internal peripheral definition dtsi.
In reply to a message not in the archiveSH7751R internal peripherals device tree.
--- arch/sh/boot/dts/sh7751r.dtsi | 105 ++++++++++++++++++++++++++++++++++ 1 file changed, 105 insertions(+) create mode 100644 arch/sh/boot/dts/sh7751r.dtsi
arch/sh/boot/dts/sh7751r.dtsi new file +105 -0
@@ -0,0 +1,105 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Device Tree Source for the SH7751R SoC + */ + +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/clock/sh7750-cpg.h> + +/ { + #address-cells = <1>; + #size-cells = <1>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + compatible = "renesas,sh4", "renesas,sh2"; + device_type = "cpu"; + reg = <0>; + clocks = <&cpg SH7750_CPG_ICK>; + clock-names = "ick"; + icache-size = <16384>; + icache-line-size = <32>; + dcache-size = <32768>; + dcache-line-size = <32>; + }; + }; + + extal: oscillator { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <0>; + clock-output-names = "extal"; + }; + + soc { + compatible = "simple-bus"; + interrupt-parent = <&shintc>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + cpg: clock-controller@ffc00000 { + #clock-cells = <1>; + #power-domain-cells = <0>; + compatible = "renesas,sh7751r-cpg"; + clocks = <&extal>; + clock-names = "extal"; + reg = <0xffc00000 20>, <0xfe0a0000 16>; + reg-names = "FRQCR", "CLKSTP00"; + renesas,mode = <0>; + }; + + shintc: interrupt-controller@ffd00000 { + compatible = "renesas,sh7751-intc"; + #interrupt-cells = <1>; + interrupt-controller; + reg = <0xffd00000 20>, <0xfe080000 128>; + reg-names = "ICR", "INTPRI00"; + }; + + /* sci0 is rarely used, so it is not defined here. */ + scif1: serial@ffe80000 { + compatible = "renesas,scif-sh7751", "renesas,scif"; + reg = <0xffe80000 0x100>; + interrupts = <0x700>, + <0x720>, + <0x760>, + <0x740>; + interrupt-names = "eri", "rxi", "txi", "bri"; + clocks = <&cpg SH7750_MSTP_SCIF>; + clock-names = "fck"; + power-domains = <&cpg>; + status = "disabled"; + }; + + /* Normally ch0 and ch1 are used, so we will define ch0 to ch2 here. */ + tmu0: timer@ffd80000 { + compatible = "renesas,tmu-sh7750", "renesas,tmu"; + reg = <0xffd80000 12>; + interrupts = <0x400>, + <0x420>, + <0x440>, + <0x460>; + interrupt-names = "tuni0", "tuni1", "tuni2", "ticpi2"; + clocks = <&cpg SH7750_MSTP_TMU012>; + clock-names = "fck"; + power-domains = <&cpg>; + #renesas,channels = <3>; + }; + + pcic: pci@fe200000 { + compatible = "renesas,sh7751-pci"; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + device_type = "pci"; + bus-range = <0 0>; + reg = <0xfe200000 0x0400>, + <0xff800000 0x0100>; + status = "disabled"; + }; + }; +};
Signature · 1 line
2.39.2
Yoshinori Sato
maintainerPATCH RESEND v7 30/37 sh: add RTS7751R2D Plus DTS
In reply to a message not in the archiveRenesas RTS7751R2D Plus devicetree.
--- arch/sh/boot/dts/rts7751r2dplus.dts | 169 ++++++++++++++++++++++++++++ 1 file changed, 169 insertions(+) create mode 100644 arch/sh/boot/dts/rts7751r2dplus.dts
arch/sh/boot/dts/rts7751r2dplus.dts new file +169 -0
@@ -0,0 +1,169 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Device Tree Source for the Renesas RTS7751R2D Plus + */ + +/dts-v1/; + +#include "sh7751r.dtsi" +#include <dt-bindings/display/sm501.h> + +/ { + model = "Renesas RTS7715R2D Plus"; + compatible = "renesas,rts7751r2d", "renesas,sh7751r"; + + aliases { + serial0 = &scif1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@c000000 { + device_type = "memory"; + reg = <0x0c000000 0x4000000>; + }; + + r2dintc: interrupt-controller@a4000000 { + compatible = "renesas,sh7751-irl-ext"; + reg = <0xa4000000 0x02>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + /* + * b15: 12 - TP + * b14: 9 - PCI INTA + * b13: 10 - PCI INTB + * b12: 3 - PCI INTC + * b11: 0 - PCI INTD + * b10: 4 - SM501 + * b9: 1 - CF IDE + * b8: 2 - CF CD + * b7: 8 - SDCARD + * b6: 5 - KEY + * b5: 6 - RTC ALARM + * b4: 7 - RTC T + * b3: unassigned + * b2: unassigned + * b1: unassigned + * b0: 11 -EXT + */ + renesas,enable-reg = <12 9 10 3 0 4 1 2 8 5 6 7 15 15 15 11>; + }; + + display@0 { + compatible = "smi,sm501"; + reg = <0x10000000 0x03e00000 + 0x13e00000 0x00200000>; + interrupt-parent = <&r2dintc>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; + mode = "640x480-16@60"; + little-endian; + smi,devices = "usb-host", "uart0"; + swap-fb-endian; + + crt { + smi,flags = "use-init-done", + "disable-at-exit", + "use-hwcursor", + "use-hwaccel"; + }; + + panel { + bpp = <16>; + edid = [00 ff ff ff ff ff ff 00 00 00 00 00 00 00 00 00 + 00 00 01 04 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 f0 0a 80 fb 20 e0 25 10 32 60 + 02 00 00 00 00 00 00 06 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 bd]; + smi,flags = "use-init-done", + "disable-at-exit", + "use-hwcursor", + "use-hwaccel"; + }; + misc-timing { + ex = <SM501_MISC_TIMING_EX_HOLD_16>; + xc = <SM501_MISC_TIMING_XC_INTERNAL>; + usb-over-current-detect-disable; + }; + misc-control { + pad = <SM501_MISC_CONTROL_PAD_24>; + usbclk = <SM501_MISC_CONTROL_USBCLK_XTAL>; + sh-ready-low; + }; + }; + + compact-flash@b4001000 { + compatible = "renesas,rts7751r2d-ata", "ata-generic"; + reg = <0xb4001000 0x0e>, <0xb400080c 2>; + reg-shift = <1>; + interrupt-parent = <&r2dintc>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; + }; + + flash@0 { + compatible = "cfi-flash"; + reg = <0x00000000 0x02000000>; + device-width = <2>; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot"; + reg = <0x00000000 0x00040000>; + }; + + partition@1 { + label = "Environemt"; + reg = <0x00040000 0x00040000>; + }; + + partition@2 { + label = "Kernel"; + reg = <0x00080000 0x001c0000>; + }; + + partition@3 { + label = "Flash_FS"; + reg = <0x00240000 0x00dc0000>; + }; + }; +}; + +&extal { + clock-frequency = <22222222>; +}; + +&cpg { + renesas,mode = <5>; +}; + +&scif1 { + status = "okay"; +}; + +&pcic { + ranges = <0x02000000 0 0xfd000000 0xfd000000 0 0x01000000>, + <0x01000000 0 0x00000000 0xfe240000 0 0x00040000>; + dma-ranges = <0x01000000 0 0xab000000 0xab000000 0 0x00000001>, + <0x02000000 0 0x0c000000 0x0c000000 0 0x04000000>, + <0x02000000 0 0xd0000000 0xd0000000 0 0x00000001>; + interrupt-map = <0x0000 0 0 1 &r2dintc 9 IRQ_TYPE_LEVEL_LOW>, + <0x0000 0 0 2 &r2dintc 10 IRQ_TYPE_LEVEL_LOW>, + <0x0000 0 0 3 &r2dintc 3 IRQ_TYPE_LEVEL_LOW>, + <0x0000 0 0 4 &r2dintc 0 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 1 &r2dintc 10 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 2 &r2dintc 3 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 3 &r2dintc 0 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 4 &r2dintc 9 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 1 &r2dintc 3 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 2 &r2dintc 0 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 3 &r2dintc 9 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 4 &r2dintc 10 IRQ_TYPE_LEVEL_LOW>; + interrupt-map-mask = <0x1800 0 0 7>; + status = "okay"; +};
Signature · 1 line
2.39.2
Yoshinori Sato
maintainerPATCH RESEND v7 31/37 sh: Add IO DATA LANDISK dts
In reply to a message not in the archiveIO DATA DEVICE Inc. LANDISK HDL-U devicetree.
--- arch/sh/boot/dts/landisk.dts | 77 ++++++++++++++++++++++++++++++++++++ 1 file changed, 77 insertions(+) create mode 100644 arch/sh/boot/dts/landisk.dts
arch/sh/boot/dts/landisk.dts new file +77 -0
@@ -0,0 +1,77 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Device Tree Source for the IO DATA DEVICE LANDISK + */ + +/dts-v1/; + +#include "sh7751r.dtsi" + +/ { + model = "IO DATA Device LANDISK"; + compatible = "iodata,landisk", "renesas,sh7751r"; + + aliases { + serial0 = &scif1; + }; + + chosen { + stdout-path = "serial0:9600n8"; + }; + + memory@c000000 { + device_type = "memory"; + reg = <0x0c000000 0x4000000>; + }; + + julianintc: interrupt-controller@b0000005 { + compatible = "renesas,sh7751-irl-ext"; + reg = <0xb0000005 0x01>; + interrupt-controller; + #interrupt-cells = <2>; + /* + * b7: Not assigned + * b6: Power switch + * b5: Not assigned + * b4: Not assigned + * b3: PCI-INTD + * b2: PCI-INTC + * b1: PCI-INTB + * b0: PCI-INTA + */ + renesas,enable-reg = <15 11 15 15 8 7 6 5>; + }; +}; + +&extal { + clock-frequency = <22222222>; +}; + +&cpg { + renesas,mode = <5>; +}; + +&scif1 { + status = "okay"; +}; + +&pcic { + ranges = <0x02000000 0 0xfd000000 0xfd000000 0 0x01000000>, + <0x01000000 0 0x00000000 0xfe240000 0 0x00040000>; + dma-ranges = <0x02000000 0 0x0c000000 0x0c000000 0 0x04000000>, + <0x02000000 0 0xd0000000 0xd0000000 0 0x00000001>; + interrupt-map = <0x0000 0 0 1 &julianintc 5 IRQ_TYPE_LEVEL_LOW>, + <0x0000 0 0 2 &julianintc 6 IRQ_TYPE_LEVEL_LOW>, + <0x0000 0 0 3 &julianintc 7 IRQ_TYPE_LEVEL_LOW>, + <0x0000 0 0 4 &julianintc 8 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 1 &julianintc 6 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 2 &julianintc 7 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 3 &julianintc 8 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 4 &julianintc 5 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 1 &julianintc 7 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 2 &julianintc 8 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 3 &julianintc 5 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 4 &julianintc 6 IRQ_TYPE_LEVEL_LOW>; + interrupt-map-mask = <0x1800 0 0 7>; + status = "okay"; +};
Signature · 1 line
2.39.2
Yoshinori Sato
maintainerPATCH RESEND v7 32/37 sh: Add IO DATA USL-5P dts
In reply to a message not in the archiveIO DATA DEVICE Inc. USL-5P devicetree.
--- arch/sh/boot/dts/usl-5p.dts | 85 +++++++++++++++++++++++++++++++++++++ 1 file changed, 85 insertions(+) create mode 100644 arch/sh/boot/dts/usl-5p.dts
arch/sh/boot/dts/usl-5p.dts new file +85 -0
@@ -0,0 +1,85 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Device Tree Source for the IO DATA DEVICE USL-5P + */ + +/dts-v1/; + +#include "sh7751r.dtsi" + +/ { + model = "IO-DATA Device USL-5P"; + compatible = "iodata,usl-5p", "renesas,sh7751r"; + + aliases { + serial0 = &scif1; + }; + + chosen { + stdout-path = "serial0:9600n8"; + }; + + memory@c000000 { + device_type = "memory"; + reg = <0x0c000000 0x4000000>; + }; + + julianintc: interrupt-controller@b0000005 { + compatible = "renesas,sh7751-irl-ext"; + reg = <0xb0000005 0x01>; + interrupt-controller; + #interrupt-cells = <2>; + /* + * b7: Button + * b6: Power switch + * b5: Compact Flash + * b4: ATA + * b3: PCI-INTD + * b2: PCI-INTC + * b1: PCI-INTB + * b0: PCI-INTA + */ + renesas,enable-reg = <12 11 10 9 8 7 6 5>; + }; + + compact-flash@b4000040 { + compatible = "iodata,usl-5p-ata", "ata-generic"; + reg = <0xb4000040 0x0e>, <0xb400002c 2>; + reg-shift = <1>; + interrupt-parent = <&julianintc>; + interrupts = <10 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +&extal { + clock-frequency = <22222222>; +}; + +&cpg { + renesas,mode = <5>; +}; + +&scif1 { + status = "okay"; +}; + +&pcic { + ranges = <0x02000000 0 0xfd000000 0xfd000000 0 0x01000000>, + <0x01000000 0 0x00000000 0xfe240000 0 0x00040000>; + dma-ranges = <0x02000000 0 0x0c000000 0x0c000000 0 0x04000000>, + <0x02000000 0 0xd0000000 0xd0000000 0 0x00000001>; + interrupt-map = <0x0000 0 0 1 &julianintc 5 IRQ_TYPE_LEVEL_LOW>, + <0x0000 0 0 2 &julianintc 6 IRQ_TYPE_LEVEL_LOW>, + <0x0000 0 0 3 &julianintc 7 IRQ_TYPE_LEVEL_LOW>, + <0x0000 0 0 4 &julianintc 8 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 1 &julianintc 6 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 2 &julianintc 7 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 3 &julianintc 8 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 4 &julianintc 5 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 1 &julianintc 7 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 2 &julianintc 8 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 3 &julianintc 5 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 4 &julianintc 6 IRQ_TYPE_LEVEL_LOW>; + interrupt-map-mask = <0x1800 0 0 7>; + status = "okay"; +};
Signature · 1 line
2.39.2
Yoshinori Sato
maintainerPATCH RESEND v7 33/37 sh: j2_mimas_v2.dts update
In reply to a message not in the archive--- arch/sh/boot/dts/j2_mimas_v2.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/sh/boot/dts/j2_mimas_v2.dts +1 -1
@@ -16,7 +16,7 @@ cpus { cpu@0 { device_type = "cpu"; - compatible = "jcore,j2"; + compatible = "jcore,j2", "renesas,sh2"; reg = <0>; clock-frequency = <50000000>; d-cache-size = <8192>;
Signature · 1 line
2.39.2
Re: [RESEND v7 33/37] sh: j2_mimas_v2.dts update
Hi Sato-san,
Quoted 1 line · Yoshinori Sato
Signed-off-by Yoshinori Sato <[email protected]>
From my comments for v6:
Please enhance the one-line summary, e.g.
sh: j2_mimas_v2: Update CPU compatible value
For the actual changes:
Gr{oetje,eeting}s,
Geert
Signature · 5 lines
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected] In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds
Yoshinori Sato
maintainerPATCH RESEND v7 34/37 sh: Add dtbs target support.
In reply to a message not in the archive--- arch/sh/boot/dts/Makefile | 5 +++++ 1 file changed, 5 insertions(+)
arch/sh/boot/dts/Makefile +5 -0
@@ -1,2 +1,7 @@ # SPDX-License-Identifier: GPL-2.0-only obj-$(CONFIG_USE_BUILTIN_DTB) += $(addsuffix .dtb.o, $(CONFIG_BUILTIN_DTB_SOURCE)) + +dtb-$(CONFIG_CPU_J2) += j2_mimas_v2.dtb +dtb-$(CONFIG_CPU_SUBTYPE_SH7751R) += landisk.dtb +dtb-$(CONFIG_CPU_SUBTYPE_SH7751R) += rts7751r2dplus.dtb +dtb-$(CONFIG_CPU_SUBTYPE_SH7751R) += usl-5p.dtb
Signature · 1 line
2.39.2
Re: [RESEND v7 34/37] sh: Add dtbs target support.
Quoted 1 line · Yoshinori Sato
Signed-off-by Yoshinori Sato <[email protected]>
My
on v6 is still valid.
Gr{oetje,eeting}s,
Geert
Signature · 5 lines
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected] In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds
Yoshinori Sato
maintainerPATCH RESEND v7 35/37 sh: RTS7751R2D Plus OF defconfig
In reply to a message not in the archive--- arch/sh/configs/rts7751r2dplus-of_defconfig | 75 +++++++++++++++++++++ 1 file changed, 75 insertions(+) create mode 100644 arch/sh/configs/rts7751r2dplus-of_defconfig
arch/sh/configs/rts7751r2dplus-of_defconfig new file +75 -0
@@ -0,0 +1,75 @@ +CONFIG_SYSVIPC=y +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_PROFILING=y +CONFIG_CPU_SUBTYPE_SH7751R=y +CONFIG_MEMORY_START=0x0c000000 +CONFIG_SH_RTS7751R2D=y +CONFIG_RTS7751R2D_PLUS=y +CONFIG_HEARTBEAT=y +CONFIG_CMDLINE="console=tty0 console=ttySC1,115200 root=/dev/sda1" +CONFIG_CMDLINE_OVERWRITE=y +CONFIG_MODULES=y +CONFIG_FLATMEM_MANUAL=y +CONFIG_NET=y +CONFIG_PACKET=y +CONFIG_UNIX=y +CONFIG_INET=y +# CONFIG_IPV6 is not set +CONFIG_PCI=y +CONFIG_HOTPLUG_PCI=y +CONFIG_UEVENT_HELPER=y +CONFIG_MTD=y +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_CFI=y +CONFIG_MTD_CFI_AMDSTD=y +CONFIG_MTD_PHYSMAP=y +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_SD=y +# CONFIG_BLK_DEV_BSG is not set +CONFIG_ATA=y +CONFIG_PATA_PLATFORM=y +CONFIG_NETDEVICES=y +CONFIG_8139TOO=y +# CONFIG_8139TOO_PIO is not set +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_SERIO is not set +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_SH_SCI=y +CONFIG_HW_RANDOM=y +CONFIG_SPI=y +CONFIG_SPI_SH_SCI=y +CONFIG_MFD_SM501=y +CONFIG_FB=y +CONFIG_FB_SH_MOBILE_LCDC=m +CONFIG_FB_SM501=y +CONFIG_FRAMEBUFFER_CONSOLE=y +CONFIG_LOGO=y +# CONFIG_LOGO_LINUX_MONO is not set +# CONFIG_LOGO_LINUX_VGA16 is not set +# CONFIG_LOGO_LINUX_CLUT224 is not set +# CONFIG_LOGO_SUPERH_MONO is not set +# CONFIG_LOGO_SUPERH_VGA16 is not set +CONFIG_SOUND=y +CONFIG_SND=m +CONFIG_SND_YMFPCI=m +CONFIG_HID_GYRATION=y +CONFIG_HID_PANTHERLORD=y +CONFIG_HID_PETALYNX=y +CONFIG_HID_SAMSUNG=y +CONFIG_HID_SUNPLUS=y +CONFIG_USB=y +CONFIG_USB_ANNOUNCE_NEW_DEVICES=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_STORAGE=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_DRV_R9701=y +CONFIG_EXT2_FS=y +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_PROC_KCORE=y +CONFIG_TMPFS=y +CONFIG_MINIX_FS=y +CONFIG_NLS_CODEPAGE_932=y +CONFIG_CRC_T10DIF=y +CONFIG_DEBUG_FS=y
Signature · 1 line
2.39.2
Yoshinori Sato
maintainerPATCH RESEND v7 36/37 sh: LANDISK OF defconfig
In reply to a message not in the archive--- arch/sh/configs/landisk-of_defconfig | 104 +++++++++++++++++++++++++++ 1 file changed, 104 insertions(+) create mode 100644 arch/sh/configs/landisk-of_defconfig
arch/sh/configs/landisk-of_defconfig new file +104 -0
@@ -0,0 +1,104 @@ +CONFIG_SYSVIPC=y +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_KEXEC=y +CONFIG_CPU_SUBTYPE_SH7751R=y +CONFIG_MEMORY_START=0x0c000000 +CONFIG_SH_OF_BOARD=y +CONFIG_HEARTBEAT=y +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +CONFIG_MODULE_FORCE_UNLOAD=y +CONFIG_FLATMEM_MANUAL=y +CONFIG_NET=y +CONFIG_PACKET=y +CONFIG_UNIX=y +CONFIG_INET=y +CONFIG_IP_ADVANCED_ROUTER=y +CONFIG_IP_PNP=y +# CONFIG_IPV6 is not set +CONFIG_NETFILTER=y +CONFIG_ATALK=m +CONFIG_PCI=y +CONFIG_PCI_SH7751=y +CONFIG_PCCARD=y +CONFIG_YENTA=y +CONFIG_UEVENT_HELPER=y +CONFIG_BLK_DEV_LOOP=y +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_SD=y +CONFIG_BLK_DEV_SR=y +# CONFIG_BLK_DEV_BSG is not set +CONFIG_ATA=y +CONFIG_PATA_ARTOP=y +CONFIG_PATA_OF_PLATFORM=y +CONFIG_ATA_GENERIC=y +CONFIG_MD=y +CONFIG_BLK_DEV_MD=m +CONFIG_MD_LINEAR=m +CONFIG_MD_RAID0=m +CONFIG_MD_RAID1=m +CONFIG_NETDEVICES=y +CONFIG_TUN=m +CONFIG_8139CP=y +CONFIG_USB_PEGASUS=m +CONFIG_USB_RTL8150=m +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_SERIO is not set +CONFIG_SERIAL_SH_SCI=y +CONFIG_HW_RANDOM=y +CONFIG_SOUND=m +CONFIG_HID_A4TECH=m +CONFIG_HID_BELKIN=m +CONFIG_HID_CHERRY=m +CONFIG_HID_CYPRESS=m +CONFIG_HID_EZKEY=m +CONFIG_HID_GYRATION=m +CONFIG_HID_MICROSOFT=m +CONFIG_HID_MONTEREY=m +CONFIG_HID_PANTHERLORD=m +CONFIG_HID_PETALYNX=m +CONFIG_HID_SAMSUNG=m +CONFIG_HID_SUNPLUS=m +CONFIG_USB_HID=m +CONFIG_USB=y +CONFIG_USB_MON=y +CONFIG_USB_EHCI_HCD=y +# CONFIG_USB_EHCI_TT_NEWSCHED is not set +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_PRINTER=m +CONFIG_USB_STORAGE=m +CONFIG_USB_STORAGE_DATAFAB=m +CONFIG_USB_STORAGE_FREECOM=m +CONFIG_USB_STORAGE_ISD200=m +CONFIG_USB_STORAGE_SDDR09=m +CONFIG_USB_STORAGE_SDDR55=m +CONFIG_USB_STORAGE_JUMPSHOT=m +CONFIG_USB_SERIAL=m +CONFIG_USB_SERIAL_FTDI_SIO=m +CONFIG_USB_SERIAL_PL2303=m +CONFIG_USB_EMI62=m +CONFIG_USB_EMI26=m +CONFIG_USB_SISUSBVGA=m +CONFIG_RENESAS_SH7751_INTC=y +CONFIG_RENESAS_SH7751IRL_INTC=y +CONFIG_EXT2_FS=y +CONFIG_EXT3_FS=y +CONFIG_REISERFS_FS=y +CONFIG_ISO9660_FS=m +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_NTFS_FS=m +CONFIG_NTFS_RW=y +CONFIG_TMPFS=y +CONFIG_ROMFS_FS=y +CONFIG_UFS_FS=m +CONFIG_NFS_FS=m +CONFIG_NFSD=m +CONFIG_NLS_CODEPAGE_437=y +CONFIG_NLS_CODEPAGE_932=y +CONFIG_INIT_STACK_NONE=y +CONFIG_CRC_T10DIF=y +CONFIG_DEBUG_KERNEL=y +# CONFIG_FTRACE is not set +CONFIG_SH_STANDARD_BIOS=y
Signature · 1 line
2.39.2
Yoshinori Sato
maintainerPATCH RESEND v7 37/37 sh: j2_defconfig: update
In reply to a message not in the archiveI've changed some symbols related to DeviceTree,
so let's take care of those changes.
--- arch/sh/configs/j2_defconfig | 11 +++-------- 1 file changed, 3 insertions(+), 8 deletions(-)
arch/sh/configs/j2_defconfig +3 -8
@@ -1,18 +1,15 @@ -CONFIG_SMP=y CONFIG_SYSVIPC=y CONFIG_POSIX_MQUEUE=y CONFIG_NO_HZ=y CONFIG_HIGH_RES_TIMERS=y CONFIG_CPU_SUBTYPE_J2=y CONFIG_MEMORY_START=0x10000000 -CONFIG_MEMORY_SIZE=0x04000000 CONFIG_CPU_BIG_ENDIAN=y -CONFIG_SH_DEVICE_TREE=y -CONFIG_SH_JCORE_SOC=y +CONFIG_SH_OF_BOARD=y CONFIG_HZ_100=y +CONFIG_SMP=y CONFIG_CMDLINE_OVERWRITE=y CONFIG_CMDLINE="console=ttyUL0 earlycon" -CONFIG_BINFMT_ELF_FDPIC=y CONFIG_BINFMT_FLAT=y CONFIG_NET=y CONFIG_PACKET=y
@@ -21,7 +18,6 @@ CONFIG_INET=y CONFIG_DEVTMPFS=y CONFIG_DEVTMPFS_MOUNT=y CONFIG_NETDEVICES=y -CONFIG_SERIAL_EARLYCON=y CONFIG_SERIAL_UARTLITE=y CONFIG_SERIAL_UARTLITE_CONSOLE=y CONFIG_I2C=y
@@ -30,8 +26,6 @@ CONFIG_SPI_JCORE=y CONFIG_WATCHDOG=y CONFIG_MMC=y CONFIG_MMC_SPI=y -CONFIG_CLKSRC_JCORE_PIT=y -CONFIG_JCORE_AIC=y CONFIG_EXT4_FS=y CONFIG_VFAT_FS=y CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
@@ -40,3 +34,4 @@ CONFIG_NLS_DEFAULT="utf8" CONFIG_NLS_CODEPAGE_437=y CONFIG_NLS_ASCII=y CONFIG_NLS_UTF8=y +CONFIG_INIT_STACK_NONE=y
Signature · 1 line
2.39.2