riscv: dts: starfive: jh7110-pine64-star64: enable usb0 host function
Subsystems (3)
v3 cover riscv: dts: starfive: jh7110-pine64-star64: enable usb0 host function
Enable host mode JH7110 on-chip USB for Pine64 Star64 by setting host mode and connect vbus pinctrl.
This functionality depends on setting the USB over-current register to disable at bootloader phase, for example U-Boot:
https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/
If the over-current register is not prepared for us then the result is no change in functional outcome with this patch applied; there is an error visible to the user and this usb configuration fails (same as it is now).
Changes since v2:
- Rebase on latest master
Changes since v1:
- Rebase on linux-next/master
- use tabs for code indent
E Shattow (1):
riscv: dts: starfive: jh7110-pine64-star64: enable usb0 host function
.../boot/dts/starfive/jh7110-pine64-star64.dts | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-)
Signature · 1 line
2.45.2
PATCH v3 1/1 riscv: dts: starfive: jh7110-pine64-star64: enable usb0 host function
Pine64 Star64 set JH7110 on-chip USB host mode and vbus pin assignment
--- .../boot/dts/starfive/jh7110-pine64-star64.dts | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-)
arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts +17 -1
@@ -80,7 +80,23 @@ &spi0 { status = "okay"; }; +&sysgpio { + usb0_pins: usb0-0 { + vbus-pins { + pinmux = <GPIOMUX(25, GPOUT_SYS_USB_DRIVE_VBUS, + GPOEN_ENABLE, + GPI_NONE)>; + bias-disable; + input-disable; + input-schmitt-disable; + slew-rate = <0>; + }; + }; +}; + &usb0 { - dr_mode = "peripheral"; + dr_mode = "host"; + pinctrl-names = "default"; + pinctrl-0 = <&usb0_pins>; status = "okay"; };
Signature · 1 line
2.45.2
Conor Dooley
maintainerEmil,
Quoted 2 lines · E Shattow
Pine64 Star64 set JH7110 on-chip USB host mode and vbus pin assignment
Looks like the same thing here, so same thing here :)
Thanks,
Conor.
Quoted 37 lines
Signed-off-by E Shattow <[email protected]>--- .../boot/dts/starfive/jh7110-pine64-star64.dts | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-)arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts +17
-1@@ -80,7 +80,23 @@ &spi0 { status = "okay"; }; +&sysgpio { + usb0_pins: usb0-0 { + vbus-pins { + pinmux = <GPIOMUX(25, GPOUT_SYS_USB_DRIVE_VBUS, + GPOEN_ENABLE, + GPI_NONE)>; + bias-disable; + input-disable; + input-schmitt-disable; + slew-rate = <0>; + }; + }; +}; + &usb0 { - dr_mode = "peripheral"; + dr_mode = "host"; + pinctrl-names = "default"; + pinctrl-0 = <&usb0_pins>; status = "okay"; };Signature · 1 line
2.45.2
Quoted 1 line · E Shattow
Pine64 Star64 set JH7110 on-chip USB host mode and vbus pin assignment
Here I'd like it explained that the Star64 board routes 1 of the 4 USB-A ports to USB0 on the SoC rather than to the USB 3.0 <-> PCIe chip.
(Confusing for users that 1 of the 4 similar ports only does USB 2.0, but that's too late to change and not relevant here)
With that fixed:
Quoted 38 lines
Signed-off-by E Shattow <[email protected]>--- .../boot/dts/starfive/jh7110-pine64-star64.dts | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-)arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts +17
-2@@ -80,7 +80,23 @@ &spi0 { status = "okay"; }; +&sysgpio { + usb0_pins: usb0-0 { + vbus-pins { + pinmux = <GPIOMUX(25, GPOUT_SYS_USB_DRIVE_VBUS, + GPOEN_ENABLE, + GPI_NONE)>; + bias-disable; + input-disable; + input-schmitt-disable; + slew-rate = <0>; + }; + }; +}; + &usb0 { - dr_mode = "peripheral"; + dr_mode = "host"; + pinctrl-names = "default"; + pinctrl-0 = <&usb0_pins>; status = "okay"; }; --2.45.2
Quoted 10 lines · Emil Renner Berthing
Quoted 1 line · E Shattow
Pine64 Star64 set JH7110 on-chip USB host mode and vbus pin assignment
Here I'd like it explained that the Star64 board routes 1 of the 4 USB-A ports to USB0 on the SoC rather than to the USB 3.0 <-> PCIe chip.
(Confusing for users that 1 of the 4 similar ports only does USB 2.0, but that's too late to change and not relevant here)
With that fixed:
Reviewed-by Emil Renner Berthing <[email protected]>
There is no (VL805) USB 3.0 <-> PCIe chip on Star64; All 4 USB-A ports route to USB0 of the SoC. What does not exist I did not write about in the cover letter. I will expand the description in the commit message. Thank you! -E
Quoted 37 lines
Quoted 37 lines
Signed-off-by E Shattow <[email protected]>--- .../boot/dts/starfive/jh7110-pine64-star64.dts | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-)arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts +17
-2@@ -80,7 +80,23 @@ &spi0 { status = "okay"; }; +&sysgpio { + usb0_pins: usb0-0 { + vbus-pins { + pinmux = <GPIOMUX(25, GPOUT_SYS_USB_DRIVE_VBUS, + GPOEN_ENABLE, + GPI_NONE)>; + bias-disable; + input-disable; + input-schmitt-disable; + slew-rate = <0>; + }; + }; +}; + &usb0 { - dr_mode = "peripheral"; + dr_mode = "host"; + pinctrl-names = "default"; + pinctrl-0 = <&usb0_pins>; status = "okay"; }; --2.45.2