Skip to contentSkip to conversation

Support RK3528 variant of Rockchip naneng-combphy

PATCH Applied Yao Zi 4 participants 11 messages Jul 28, 2025 – Aug 22, 2025

Subsystems (3)
lore
Share & tools
lore

Yao Zi

author
#0 lore raw

v5 cover Support RK3528 variant of Rockchip naneng-combphy

Rockchip RK3528 ships a naneng-combphy that operates in either PCIe or USB 3.0 mode. It has a similar control logic to previous generations of naneng-combphy but an apparently different register layout.

This series prepares phy-rockchip-naneng-combphy.c for variants with a different register layout and add RK3528 support.

Testing is done on both Radxa E20C and Radxa Rock 2A with downstream devicetree changes, both USB 3 and PCIe modes are verified with mainline
driver, and reach a reasonable speed.

This series depends on patch "phy: rockchip: naneng-combphy: Enable U3 OTG port for RK3568"[1], and the dts patch depends on v2 of patch "arm64: dts: rockchip: convert rk3528 power-domains to dt-binding constants"[2] to build.

[1]: https://lore.kernel.org/all/[email protected]/
[2]: https://lore.kernel.org/all/[email protected]/

Changed from v4
- Collect review tags
- Add extra handling of USB3OTG_CON1 when operating in USB3 mode
- Link to v4: https://lore.kernel.org/all/[email protected]/
Changed from v3
- Add a dt-binding patch to allow power-domains property when describing Rockchip naneng combphys
- devicetree patch
- Break down long lines
- Sort properties to keep the style consistent
- Add power-domains property to the combphy node
- Link to v3: https://lore.kernel.org/linux-rockchip/[email protected]/
Changed from v2
- phy binding patch
- Fix format issue
- drop review tags
- Link to v2: https://lore.kernel.org/all/20250509004121.36058-2-ziyao@disroot.
org/
Changed from v1
- Collect review tags
- Restyle RK3528 register definitions in the combphy driver
- Drop unused include of phy.h in SoC devicetree
- Link to v1: https://lore.kernel.org/all/20250508134332.14668-2-ziyao@disroo
t.org/

Yao Zi (6):
dt-bindings: soc: rockchip: Add RK3528 pipe-phy GRF syscon
dt-bindings: phy: rockchip: naneng-combphy: Add power-domains property
dt-bindings: phy: rockchip: naneng-combphy: Add RK3528 variant
phy: rockchip: naneng-combphy: Add SoC prefix to register definitions
phy: rockchip: naneng-combphy: Add RK3528 support
arm64: dts: rockchip: Add naneng-combphy for RK3528

 .../phy/phy-rockchip-naneng-combphy.yaml      |   8 +-
 .../devicetree/bindings/soc/rockchip/grf.yaml |   1 +
 arch/arm64/boot/dts/rockchip/rk3528.dtsi      |  24 +
 .../rockchip/phy-rockchip-naneng-combphy.c    | 749 +++++++++++-------
 4 files changed, 508 insertions(+), 274 deletions(-)
Signature · 1 line
2.50.1
author
#1 lore raw

PATCH v5 1/6 dt-bindings: soc: rockchip: Add RK3528 pipe-phy GRF syscon

Add compatible string for pipe-phy GRF found on RK3528 SoC, which controls misc settings for the integrated naneng-combphy.

---
 Documentation/devicetree/bindings/soc/rockchip/grf.yaml | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/soc/rockchip/grf.yaml +1 -0
index 1ab0b092e2a5..fe5361713167 100644
@@ -16,6 +16,7 @@ properties:
           - enum:
               - rockchip,rk3288-sgrf
               - rockchip,rk3528-ioc-grf
+              - rockchip,rk3528-pipe-phy-grf
               - rockchip,rk3528-vo-grf
               - rockchip,rk3528-vpu-grf
               - rockchip,rk3562-ioc-grf
Signature · 1 line
2.50.1
author
#2 lore raw

PATCH v5 2/6 dt-bindings: phy: rockchip: naneng-combphy: Add power-domains property

In reply to Yao Zi

Though isn't described in existing devicetrees, most Rockchip combphys belong to a specific power-domain of the SoC. Taking RK3588 as example, combphy 0 and combphy 2 belong to the PD_BUS domain. Document the power-domains property to allow describing the information correctly in devicetree.

---
 .../devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml   | 3 +++
 1 file changed, 3 insertions(+)
Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml +3 -0
index 3e101c3c5ea9..db293d2fbf1a 100644
@@ -45,6 +45,9 @@ properties:
   phy-supply:
     description: Single PHY regulator
 
+  power-domains:
+    maxItems: 1
+
   rockchip,enable-ssc:
     type: boolean
     description:
Signature · 1 line
2.50.1
author
#3 lore raw

PATCH v5 3/6 dt-bindings: phy: rockchip: naneng-combphy: Add RK3528 variant

In reply to Yao Zi

Rockchip RK3528 ships one naneng-combphy which operates in either PCIe or USB 3 mode. Document its compatible string.

---
 .../devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml +4 -1
index db293d2fbf1a..379b08bd9e97 100644
@@ -12,6 +12,7 @@ maintainers:
 properties:
   compatible:
     enum:
+      - rockchip,rk3528-naneng-combphy
       - rockchip,rk3562-naneng-combphy
       - rockchip,rk3568-naneng-combphy
       - rockchip,rk3576-naneng-combphy
@@ -108,7 +109,9 @@ allOf:
       properties:
         compatible:
           contains:
-            const: rockchip,rk3588-naneng-combphy
+            enum:
+              - rockchip,rk3528-naneng-combphy
+              - rockchip,rk3588-naneng-combphy
     then:
       properties:
         resets:
Signature · 1 line
2.50.1
author
#4 lore raw

PATCH v5 4/6 phy: rockchip: naneng-combphy: Add SoC prefix to register definitions

In reply to Yao Zi

All supported variants of naneng-combphy follow a register layout similar to the RK3568 variant with some exceptions of SoC-specific registers.

Add RK3568 prefix for the common set of registers and the corresponding SoC prefix for SoC-specific registers, making usage of definitions clear and preparing for future COMBPHY variants with a different register layout.

---
 .../rockchip/phy-rockchip-naneng-combphy.c    | 560 +++++++++---------
 1 file changed, 288 insertions(+), 272 deletions(-)
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +288 -272
index 17c6310f4b54..ce84166cd772 100644
@@ -21,78 +21,80 @@
 #define REF_CLOCK_100MHz		(100 * HZ_PER_MHZ)
 
 /* COMBO PHY REG */
-#define PHYREG6				0x14
-#define PHYREG6_PLL_DIV_MASK		GENMASK(7, 6)
-#define PHYREG6_PLL_DIV_SHIFT		6
-#define PHYREG6_PLL_DIV_2		1
-
-#define PHYREG7				0x18
-#define PHYREG7_TX_RTERM_MASK		GENMASK(7, 4)
-#define PHYREG7_TX_RTERM_SHIFT		4
-#define PHYREG7_TX_RTERM_50OHM		8
-#define PHYREG7_RX_RTERM_MASK		GENMASK(3, 0)
-#define PHYREG7_RX_RTERM_SHIFT		0
-#define PHYREG7_RX_RTERM_44OHM		15
-
-#define PHYREG8				0x1C
-#define PHYREG8_SSC_EN			BIT(4)
-
-#define PHYREG10			0x24
-#define PHYREG10_SSC_PCM_MASK		GENMASK(3, 0)
-#define PHYREG10_SSC_PCM_3500PPM	7
-
-#define PHYREG11			0x28
-#define PHYREG11_SU_TRIM_0_7		0xF0
-
-#define PHYREG12			0x2C
-#define PHYREG12_PLL_LPF_ADJ_VALUE	4
-
-#define PHYREG13			0x30
-#define PHYREG13_RESISTER_MASK		GENMASK(5, 4)
-#define PHYREG13_RESISTER_SHIFT		0x4
-#define PHYREG13_RESISTER_HIGH_Z	3
-#define PHYREG13_CKRCV_AMP0		BIT(7)
-
-#define PHYREG14			0x34
-#define PHYREG14_CKRCV_AMP1		BIT(0)
-
-#define PHYREG15			0x38
-#define PHYREG15_CTLE_EN		BIT(0)
-#define PHYREG15_SSC_CNT_MASK		GENMASK(7, 6)
-#define PHYREG15_SSC_CNT_SHIFT		6
-#define PHYREG15_SSC_CNT_VALUE		1
-
-#define PHYREG16			0x3C
-#define PHYREG16_SSC_CNT_VALUE		0x5f
-
-#define PHYREG17			0x40
-
-#define PHYREG18			0x44
-#define PHYREG18_PLL_LOOP		0x32
-
-#define PHYREG21			0x50
-#define PHYREG21_RX_SQUELCH_VAL		0x0D
-
-#define PHYREG27			0x6C
-#define PHYREG27_RX_TRIM_RK3588		0x4C
-
-#define PHYREG30			0x74
-
-#define PHYREG32			0x7C
-#define PHYREG32_SSC_MASK		GENMASK(7, 4)
-#define PHYREG32_SSC_DIR_MASK		GENMASK(5, 4)
-#define PHYREG32_SSC_DIR_SHIFT		4
-#define PHYREG32_SSC_UPWARD		0
-#define PHYREG32_SSC_DOWNWARD		1
-#define PHYREG32_SSC_OFFSET_MASK	GENMASK(7, 6)
-#define PHYREG32_SSC_OFFSET_SHIFT	6
-#define PHYREG32_SSC_OFFSET_500PPM	1
-
-#define PHYREG33			0x80
-#define PHYREG33_PLL_KVCO_MASK		GENMASK(4, 2)
-#define PHYREG33_PLL_KVCO_SHIFT		2
-#define PHYREG33_PLL_KVCO_VALUE		2
-#define PHYREG33_PLL_KVCO_VALUE_RK3576	4
+#define RK3568_PHYREG6				0x14
+#define RK3568_PHYREG6_PLL_DIV_MASK		GENMASK(7, 6)
+#define RK3568_PHYREG6_PLL_DIV_SHIFT		6
+#define RK3568_PHYREG6_PLL_DIV_2		1
+
+#define RK3568_PHYREG7				0x18
+#define RK3568_PHYREG7_TX_RTERM_MASK		GENMASK(7, 4)
+#define RK3568_PHYREG7_TX_RTERM_SHIFT		4
+#define RK3568_PHYREG7_TX_RTERM_50OHM		8
+#define RK3568_PHYREG7_RX_RTERM_MASK		GENMASK(3, 0)
+#define RK3568_PHYREG7_RX_RTERM_SHIFT		0
+#define RK3568_PHYREG7_RX_RTERM_44OHM		15
+
+#define RK3568_PHYREG8				0x1C
+#define RK3568_PHYREG8_SSC_EN			BIT(4)
+
+#define RK3568_PHYREG11				0x28
+#define RK3568_PHYREG11_SU_TRIM_0_7		0xF0
+
+#define RK3568_PHYREG12				0x2C
+#define RK3568_PHYREG12_PLL_LPF_ADJ_VALUE	4
+
+#define RK3568_PHYREG13				0x30
+#define RK3568_PHYREG13_RESISTER_MASK		GENMASK(5, 4)
+#define RK3568_PHYREG13_RESISTER_SHIFT		0x4
+#define RK3568_PHYREG13_RESISTER_HIGH_Z		3
+#define RK3568_PHYREG13_CKRCV_AMP0		BIT(7)
+
+#define RK3568_PHYREG14				0x34
+#define RK3568_PHYREG14_CKRCV_AMP1		BIT(0)
+
+#define RK3568_PHYREG15				0x38
+#define RK3568_PHYREG15_CTLE_EN			BIT(0)
+#define RK3568_PHYREG15_SSC_CNT_MASK		GENMASK(7, 6)
+#define RK3568_PHYREG15_SSC_CNT_SHIFT		6
+#define RK3568_PHYREG15_SSC_CNT_VALUE		1
+
+#define RK3568_PHYREG16				0x3C
+#define RK3568_PHYREG16_SSC_CNT_VALUE		0x5f
+
+#define RK3568_PHYREG18				0x44
+#define RK3568_PHYREG18_PLL_LOOP		0x32
+
+#define RK3568_PHYREG32				0x7C
+#define RK3568_PHYREG32_SSC_MASK		GENMASK(7, 4)
+#define RK3568_PHYREG32_SSC_DIR_MASK		GENMASK(5, 4)
+#define RK3568_PHYREG32_SSC_DIR_SHIFT		4
+#define RK3568_PHYREG32_SSC_UPWARD		0
+#define RK3568_PHYREG32_SSC_DOWNWARD		1
+#define RK3568_PHYREG32_SSC_OFFSET_MASK	GENMASK(7, 6)
+#define RK3568_PHYREG32_SSC_OFFSET_SHIFT	6
+#define RK3568_PHYREG32_SSC_OFFSET_500PPM	1
+
+#define RK3568_PHYREG33				0x80
+#define RK3568_PHYREG33_PLL_KVCO_MASK		GENMASK(4, 2)
+#define RK3568_PHYREG33_PLL_KVCO_SHIFT		2
+#define RK3568_PHYREG33_PLL_KVCO_VALUE		2
+#define RK3576_PHYREG33_PLL_KVCO_VALUE		4
+
+/* RK3588 COMBO PHY registers */
+#define RK3588_PHYREG27				0x6C
+#define RK3588_PHYREG27_RX_TRIM			0x4C
+
+/* RK3576 COMBO PHY registers */
+#define RK3576_PHYREG10				0x24
+#define RK3576_PHYREG10_SSC_PCM_MASK		GENMASK(3, 0)
+#define RK3576_PHYREG10_SSC_PCM_3500PPM		7
+
+#define RK3576_PHYREG17				0x40
+
+#define RK3576_PHYREG21				0x50
+#define RK3576_PHYREG21_RX_SQUELCH_VAL		0x0D
+
+#define RK3576_PHYREG30				0x74
 
 struct rockchip_combphy_priv;
 
@@ -407,9 +409,8 @@ static int rk3562_combphy_cfg(struct rockchip_combphy_priv *priv)
 	switch (priv->type) {
 	case PHY_TYPE_PCIE:
 		/* Set SSC downward spread spectrum */
-		rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK,
-					 PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT,
-					 PHYREG32);
+		val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
+		rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
 
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
@@ -418,29 +419,30 @@ static int rk3562_combphy_cfg(struct rockchip_combphy_priv *priv)
 		break;
 	case PHY_TYPE_USB3:
 		/* Set SSC downward spread spectrum */
-		rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK,
-					 PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT,
-					 PHYREG32);
+		val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
+		rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val,
+					 RK3568_PHYREG32);
 
 		/* Enable adaptive CTLE for USB3.0 Rx */
-		rockchip_combphy_updatel(priv, PHYREG15_CTLE_EN,
-					 PHYREG15_CTLE_EN, PHYREG15);
+		rockchip_combphy_updatel(priv, RK3568_PHYREG15_CTLE_EN,
+					 RK3568_PHYREG15_CTLE_EN, RK3568_PHYREG15);
 
 		/* Set PLL KVCO fine tuning signals */
-		rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK, BIT(3), PHYREG33);
+		rockchip_combphy_updatel(priv, RK3568_PHYREG33_PLL_KVCO_MASK,
+					 BIT(3), RK3568_PHYREG33);
 
 		/* Set PLL LPF R1 to su_trim[10:7]=1001 */
-		writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12);
+		writel(RK3568_PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + RK3568_PHYREG12);
 
 		/* Set PLL input clock divider 1/2 */
-		val = FIELD_PREP(PHYREG6_PLL_DIV_MASK, PHYREG6_PLL_DIV_2);
-		rockchip_combphy_updatel(priv, PHYREG6_PLL_DIV_MASK, val, PHYREG6);
+		val = FIELD_PREP(RK3568_PHYREG6_PLL_DIV_MASK, RK3568_PHYREG6_PLL_DIV_2);
+		rockchip_combphy_updatel(priv, RK3568_PHYREG6_PLL_DIV_MASK, val, RK3568_PHYREG6);
 
 		/* Set PLL loop divider */
-		writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18);
+		writel(RK3568_PHYREG18_PLL_LOOP, priv->mmio + RK3568_PHYREG18);
 
 		/* Set PLL KVCO to min and set PLL charge pump current to max */
-		writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11);
+		writel(RK3568_PHYREG11_SU_TRIM_0_7, priv->mmio + RK3568_PHYREG11);
 
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_sel_usb, true);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false);
@@ -458,11 +460,12 @@ static int rk3562_combphy_cfg(struct rockchip_combphy_priv *priv)
 	case REF_CLOCK_24MHz:
 		if (priv->type == PHY_TYPE_USB3) {
 			/* Set ssc_cnt[9:0]=0101111101 & 31.5KHz */
-			val = FIELD_PREP(PHYREG15_SSC_CNT_MASK, PHYREG15_SSC_CNT_VALUE);
-			rockchip_combphy_updatel(priv, PHYREG15_SSC_CNT_MASK,
-						 val, PHYREG15);
+			val = FIELD_PREP(RK3568_PHYREG15_SSC_CNT_MASK,
+					 RK3568_PHYREG15_SSC_CNT_VALUE);
+			rockchip_combphy_updatel(priv, RK3568_PHYREG15_SSC_CNT_MASK,
+						 val, RK3568_PHYREG15);
 
-			writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
+			writel(RK3568_PHYREG16_SSC_CNT_VALUE, priv->mmio + RK3568_PHYREG16);
 		}
 		break;
 	case REF_CLOCK_25MHz:
@@ -472,19 +475,20 @@ static int rk3562_combphy_cfg(struct rockchip_combphy_priv *priv)
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_100m, true);
 		if (priv->type == PHY_TYPE_PCIE) {
 			/* PLL KVCO tuning fine */
-			val = FIELD_PREP(PHYREG33_PLL_KVCO_MASK, PHYREG33_PLL_KVCO_VALUE);
-			rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
-						 val, PHYREG33);
+			val = FIELD_PREP(RK3568_PHYREG33_PLL_KVCO_MASK,
+					 RK3568_PHYREG33_PLL_KVCO_VALUE);
+			rockchip_combphy_updatel(priv, RK3568_PHYREG33_PLL_KVCO_MASK,
+						 val, RK3568_PHYREG33);
 
 			/* Enable controlling random jitter, aka RMJ */
-			writel(0x4, priv->mmio + PHYREG12);
+			writel(0x4, priv->mmio + RK3568_PHYREG12);
 
-			val = PHYREG6_PLL_DIV_2 << PHYREG6_PLL_DIV_SHIFT;
-			rockchip_combphy_updatel(priv, PHYREG6_PLL_DIV_MASK,
-						 val, PHYREG6);
+			val = RK3568_PHYREG6_PLL_DIV_2 << RK3568_PHYREG6_PLL_DIV_SHIFT;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG6_PLL_DIV_MASK,
+						 val, RK3568_PHYREG6);
 
-			writel(0x32, priv->mmio + PHYREG18);
-			writel(0xf0, priv->mmio + PHYREG11);
+			writel(0x32, priv->mmio + RK3568_PHYREG18);
+			writel(0xf0, priv->mmio + RK3568_PHYREG11);
 		}
 		break;
 	default:
@@ -495,20 +499,21 @@ static int rk3562_combphy_cfg(struct rockchip_combphy_priv *priv)
 	if (priv->ext_refclk) {
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_ext, true);
 		if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) {
-			val = PHYREG13_RESISTER_HIGH_Z << PHYREG13_RESISTER_SHIFT;
-			val |= PHYREG13_CKRCV_AMP0;
-			rockchip_combphy_updatel(priv, PHYREG13_RESISTER_MASK, val, PHYREG13);
-
-			val = readl(priv->mmio + PHYREG14);
-			val |= PHYREG14_CKRCV_AMP1;
-			writel(val, priv->mmio + PHYREG14);
+			val = RK3568_PHYREG13_RESISTER_HIGH_Z << RK3568_PHYREG13_RESISTER_SHIFT;
+			val |= RK3568_PHYREG13_CKRCV_AMP0;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG13_RESISTER_MASK, val,
+						 RK3568_PHYREG13);
+
+			val = readl(priv->mmio + RK3568_PHYREG14);
+			val |= RK3568_PHYREG14_CKRCV_AMP1;
+			writel(val, priv->mmio + RK3568_PHYREG14);
 		}
 	}
 
 	if (priv->enable_ssc) {
-		val = readl(priv->mmio + PHYREG8);
-		val |= PHYREG8_SSC_EN;
-		writel(val, priv->mmio + PHYREG8);
+		val = readl(priv->mmio + RK3568_PHYREG8);
+		val |= RK3568_PHYREG8_SSC_EN;
+		writel(val, priv->mmio + RK3568_PHYREG8);
 	}
 
 	return 0;
@@ -555,9 +560,9 @@ static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
 	switch (priv->type) {
 	case PHY_TYPE_PCIE:
 		/* Set SSC downward spread spectrum. */
-		rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK,
-					 PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT,
-					 PHYREG32);
+		val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
+
+		rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
 
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
@@ -567,30 +572,28 @@ static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
 
 	case PHY_TYPE_USB3:
 		/* Set SSC downward spread spectrum. */
-		rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK,
-					 PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT,
-					 PHYREG32);
+		val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT,
+		rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
 
 		/* Enable adaptive CTLE for USB3.0 Rx. */
-		val = readl(priv->mmio + PHYREG15);
-		val |= PHYREG15_CTLE_EN;
-		writel(val, priv->mmio + PHYREG15);
+		val = readl(priv->mmio + RK3568_PHYREG15);
+		val |= RK3568_PHYREG15_CTLE_EN;
+		writel(val, priv->mmio + RK3568_PHYREG15);
 
 		/* Set PLL KVCO fine tuning signals. */
-		rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
-					 PHYREG33_PLL_KVCO_VALUE << PHYREG33_PLL_KVCO_SHIFT,
-					 PHYREG33);
+		val = RK3568_PHYREG33_PLL_KVCO_VALUE << RK3568_PHYREG33_PLL_KVCO_SHIFT;
+		rockchip_combphy_updatel(priv, RK3568_PHYREG33_PLL_KVCO_MASK, val, RK3568_PHYREG33);
 
 		/* Enable controlling random jitter. */
-		writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12);
+		writel(RK3568_PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + RK3568_PHYREG12);
 
 		/* Set PLL input clock divider 1/2. */
-		rockchip_combphy_updatel(priv, PHYREG6_PLL_DIV_MASK,
-					 PHYREG6_PLL_DIV_2 << PHYREG6_PLL_DIV_SHIFT,
-					 PHYREG6);
+		rockchip_combphy_updatel(priv, RK3568_PHYREG6_PLL_DIV_MASK,
+					 RK3568_PHYREG6_PLL_DIV_2 << RK3568_PHYREG6_PLL_DIV_SHIFT,
+					 RK3568_PHYREG6);
 
-		writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18);
-		writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11);
+		writel(RK3568_PHYREG18_PLL_LOOP, priv->mmio + RK3568_PHYREG18);
+		writel(RK3568_PHYREG11_SU_TRIM_0_7, priv->mmio + RK3568_PHYREG11);
 
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_sel_usb, true);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false);
@@ -608,16 +611,16 @@ static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
 
 	case PHY_TYPE_SATA:
 		/* Enable adaptive CTLE for SATA Rx. */
-		val = readl(priv->mmio + PHYREG15);
-		val |= PHYREG15_CTLE_EN;
-		writel(val, priv->mmio + PHYREG15);
+		val = readl(priv->mmio + RK3568_PHYREG15);
+		val |= RK3568_PHYREG15_CTLE_EN;
+		writel(val, priv->mmio + RK3568_PHYREG15);
 		/*
 		 * Set tx_rterm=50ohm and rx_rterm=44ohm for SATA.
 		 * 0: 60ohm, 8: 50ohm 15: 44ohm (by step abort 1ohm)
 		 */
-		val = PHYREG7_TX_RTERM_50OHM << PHYREG7_TX_RTERM_SHIFT;
-		val |= PHYREG7_RX_RTERM_44OHM << PHYREG7_RX_RTERM_SHIFT;
-		writel(val, priv->mmio + PHYREG7);
+		val = RK3568_PHYREG7_TX_RTERM_50OHM << RK3568_PHYREG7_TX_RTERM_SHIFT;
+		val |= RK3568_PHYREG7_RX_RTERM_44OHM << RK3568_PHYREG7_RX_RTERM_SHIFT;
+		writel(val, priv->mmio + RK3568_PHYREG7);
 
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_sata, true);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_sata, true);
@@ -652,11 +655,11 @@ static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
 	case REF_CLOCK_24MHz:
 		if (priv->type == PHY_TYPE_USB3 || priv->type == PHY_TYPE_SATA) {
 			/* Set ssc_cnt[9:0]=0101111101 & 31.5KHz. */
-			val = PHYREG15_SSC_CNT_VALUE << PHYREG15_SSC_CNT_SHIFT;
-			rockchip_combphy_updatel(priv, PHYREG15_SSC_CNT_MASK,
-						 val, PHYREG15);
+			val = RK3568_PHYREG15_SSC_CNT_VALUE << RK3568_PHYREG15_SSC_CNT_SHIFT;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG15_SSC_CNT_MASK,
+						 val, RK3568_PHYREG15);
 
-			writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
+			writel(RK3568_PHYREG16_SSC_CNT_VALUE, priv->mmio + RK3568_PHYREG16);
 		}
 		break;
 
@@ -668,24 +671,26 @@ static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_100m, true);
 		if (priv->type == PHY_TYPE_PCIE) {
 			/* PLL KVCO  fine tuning. */
-			val = PHYREG33_PLL_KVCO_VALUE << PHYREG33_PLL_KVCO_SHIFT;
-			rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
-						 val, PHYREG33);
+			val = RK3568_PHYREG33_PLL_KVCO_VALUE << RK3568_PHYREG33_PLL_KVCO_SHIFT;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG33_PLL_KVCO_MASK,
+						 val, RK3568_PHYREG33);
 
 			/* Enable controlling random jitter. */
-			writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12);
+			writel(RK3568_PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + RK3568_PHYREG12);
 
-			val = PHYREG6_PLL_DIV_2 << PHYREG6_PLL_DIV_SHIFT;
-			rockchip_combphy_updatel(priv, PHYREG6_PLL_DIV_MASK,
-						 val, PHYREG6);
+			val = RK3568_PHYREG6_PLL_DIV_2 << RK3568_PHYREG6_PLL_DIV_SHIFT;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG6_PLL_DIV_MASK,
+						 val, RK3568_PHYREG6);
 
-			writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18);
-			writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11);
+			writel(RK3568_PHYREG18_PLL_LOOP, priv->mmio + RK3568_PHYREG18);
+			writel(RK3568_PHYREG11_SU_TRIM_0_7, priv->mmio + RK3568_PHYREG11);
 		} else if (priv->type == PHY_TYPE_SATA) {
 			/* downward spread spectrum +500ppm */
-			val = PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT;
-			val |= PHYREG32_SSC_OFFSET_500PPM << PHYREG32_SSC_OFFSET_SHIFT;
-			rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, val, PHYREG32);
+			val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
+			val |= RK3568_PHYREG32_SSC_OFFSET_500PPM <<
+			       RK3568_PHYREG32_SSC_OFFSET_SHIFT;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val,
+						 RK3568_PHYREG32);
 		}
 		break;
 
@@ -697,20 +702,21 @@ static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
 	if (priv->ext_refclk) {
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_ext, true);
 		if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) {
-			val = PHYREG13_RESISTER_HIGH_Z << PHYREG13_RESISTER_SHIFT;
-			val |= PHYREG13_CKRCV_AMP0;
-			rockchip_combphy_updatel(priv, PHYREG13_RESISTER_MASK, val, PHYREG13);
-
-			val = readl(priv->mmio + PHYREG14);
-			val |= PHYREG14_CKRCV_AMP1;
-			writel(val, priv->mmio + PHYREG14);
+			val = RK3568_PHYREG13_RESISTER_HIGH_Z << RK3568_PHYREG13_RESISTER_SHIFT;
+			val |= RK3568_PHYREG13_CKRCV_AMP0;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG13_RESISTER_MASK, val,
+						 RK3568_PHYREG13);
+
+			val = readl(priv->mmio + RK3568_PHYREG14);
+			val |= RK3568_PHYREG14_CKRCV_AMP1;
+			writel(val, priv->mmio + RK3568_PHYREG14);
 		}
 	}
 
 	if (priv->enable_ssc) {
-		val = readl(priv->mmio + PHYREG8);
-		val |= PHYREG8_SSC_EN;
-		writel(val, priv->mmio + PHYREG8);
+		val = readl(priv->mmio + RK3568_PHYREG8);
+		val |= RK3568_PHYREG8_SSC_EN;
+		writel(val, priv->mmio + RK3568_PHYREG8);
 	}
 
 	return 0;
@@ -771,8 +777,8 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
 	switch (priv->type) {
 	case PHY_TYPE_PCIE:
 		/* Set SSC downward spread spectrum */
-		val = FIELD_PREP(PHYREG32_SSC_MASK, PHYREG32_SSC_DOWNWARD);
-		rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, val, PHYREG32);
+		val = FIELD_PREP(RK3568_PHYREG32_SSC_MASK, RK3568_PHYREG32_SSC_DOWNWARD);
+		rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
 
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
@@ -782,32 +788,33 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
 
 	case PHY_TYPE_USB3:
 		/* Set SSC downward spread spectrum */
-		val = FIELD_PREP(PHYREG32_SSC_MASK, PHYREG32_SSC_DOWNWARD);
-		rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, val, PHYREG32);
+		val = FIELD_PREP(RK3568_PHYREG32_SSC_MASK, RK3568_PHYREG32_SSC_DOWNWARD);
+		rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
 
 		/* Enable adaptive CTLE for USB3.0 Rx */
-		val = readl(priv->mmio + PHYREG15);
-		val |= PHYREG15_CTLE_EN;
-		writel(val, priv->mmio + PHYREG15);
+		val = readl(priv->mmio + RK3568_PHYREG15);
+		val |= RK3568_PHYREG15_CTLE_EN;
+		writel(val, priv->mmio + RK3568_PHYREG15);
 
 		/* Set PLL KVCO fine tuning signals */
-		rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK, BIT(3), PHYREG33);
+		rockchip_combphy_updatel(priv, RK3568_PHYREG33_PLL_KVCO_MASK, BIT(3),
+					 RK3568_PHYREG33);
 
 		/* Set PLL LPF R1 to su_trim[10:7]=1001 */
-		writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12);
+		writel(RK3568_PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + RK3568_PHYREG12);
 
 		/* Set PLL input clock divider 1/2 */
-		val = FIELD_PREP(PHYREG6_PLL_DIV_MASK, PHYREG6_PLL_DIV_2);
-		rockchip_combphy_updatel(priv, PHYREG6_PLL_DIV_MASK, val, PHYREG6);
+		val = FIELD_PREP(RK3568_PHYREG6_PLL_DIV_MASK, RK3568_PHYREG6_PLL_DIV_2);
+		rockchip_combphy_updatel(priv, RK3568_PHYREG6_PLL_DIV_MASK, val, RK3568_PHYREG6);
 
 		/* Set PLL loop divider */
-		writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18);
+		writel(RK3568_PHYREG18_PLL_LOOP, priv->mmio + RK3568_PHYREG18);
 
 		/* Set PLL KVCO to min and set PLL charge pump current to max */
-		writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11);
+		writel(RK3568_PHYREG11_SU_TRIM_0_7, priv->mmio + RK3568_PHYREG11);
 
 		/* Set Rx squelch input filler bandwidth */
-		writel(PHYREG21_RX_SQUELCH_VAL, priv->mmio + PHYREG21);
+		writel(RK3576_PHYREG21_RX_SQUELCH_VAL, priv->mmio + RK3576_PHYREG21);
 
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txelec_sel, false);
@@ -816,14 +823,14 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
 
 	case PHY_TYPE_SATA:
 		/* Enable adaptive CTLE for SATA Rx */
-		val = readl(priv->mmio + PHYREG15);
-		val |= PHYREG15_CTLE_EN;
-		writel(val, priv->mmio + PHYREG15);
+		val = readl(priv->mmio + RK3568_PHYREG15);
+		val |= RK3568_PHYREG15_CTLE_EN;
+		writel(val, priv->mmio + RK3568_PHYREG15);
 
 		/* Set tx_rterm = 50 ohm and rx_rterm = 43.5 ohm */
-		val = PHYREG7_TX_RTERM_50OHM << PHYREG7_TX_RTERM_SHIFT;
-		val |= PHYREG7_RX_RTERM_44OHM << PHYREG7_RX_RTERM_SHIFT;
-		writel(val, priv->mmio + PHYREG7);
+		val = RK3568_PHYREG7_TX_RTERM_50OHM << RK3568_PHYREG7_TX_RTERM_SHIFT;
+		val |= RK3568_PHYREG7_RX_RTERM_44OHM << RK3568_PHYREG7_RX_RTERM_SHIFT;
+		writel(val, priv->mmio + RK3568_PHYREG7);
 
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_sata, true);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_sata, true);
@@ -845,19 +852,21 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_24m, true);
 		if (priv->type == PHY_TYPE_USB3 || priv->type == PHY_TYPE_SATA) {
 			/* Set ssc_cnt[9:0]=0101111101 & 31.5KHz */
-			val = FIELD_PREP(PHYREG15_SSC_CNT_MASK, PHYREG15_SSC_CNT_VALUE);
-			rockchip_combphy_updatel(priv, PHYREG15_SSC_CNT_MASK,
-						 val, PHYREG15);
+			val = FIELD_PREP(RK3568_PHYREG15_SSC_CNT_MASK,
+					 RK3568_PHYREG15_SSC_CNT_VALUE);
+			rockchip_combphy_updatel(priv, RK3568_PHYREG15_SSC_CNT_MASK,
+						 val, RK3568_PHYREG15);
 
-			writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
+			writel(RK3568_PHYREG16_SSC_CNT_VALUE, priv->mmio + RK3568_PHYREG16);
 		} else if (priv->type == PHY_TYPE_PCIE) {
 			/* PLL KVCO tuning fine */
-			val = FIELD_PREP(PHYREG33_PLL_KVCO_MASK, PHYREG33_PLL_KVCO_VALUE_RK3576);
-			rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
-						 val, PHYREG33);
+			val = FIELD_PREP(RK3568_PHYREG33_PLL_KVCO_MASK,
+					 RK3576_PHYREG33_PLL_KVCO_VALUE);
+			rockchip_combphy_updatel(priv, RK3568_PHYREG33_PLL_KVCO_MASK,
+						 val, RK3568_PHYREG33);
 
 			/* Set up rx_pck invert and rx msb to disable */
-			writel(0x00, priv->mmio + PHYREG27);
+			writel(0x00, priv->mmio + RK3588_PHYREG27);
 
 			/*
 			 * Set up SU adjust signal:
@@ -865,11 +874,11 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
 			 * su_trim[15:8],  PLL LPF R1 adujst bits[9:7]=3'b011
 			 * su_trim[31:24], CKDRV adjust
 			 */
-			writel(0x90, priv->mmio + PHYREG11);
-			writel(0x02, priv->mmio + PHYREG12);
-			writel(0x57, priv->mmio + PHYREG14);
+			writel(0x90, priv->mmio + RK3568_PHYREG11);
+			writel(0x02, priv->mmio + RK3568_PHYREG12);
+			writel(0x57, priv->mmio + RK3568_PHYREG14);
 
-			writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
+			writel(RK3568_PHYREG16_SSC_CNT_VALUE, priv->mmio + RK3568_PHYREG16);
 		}
 		break;
 
@@ -881,15 +890,16 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_100m, true);
 		if (priv->type == PHY_TYPE_PCIE) {
 			/* gate_tx_pck_sel length select work for L1SS */
-			writel(0xc0, priv->mmio + PHYREG30);
+			writel(0xc0, priv->mmio + RK3576_PHYREG30);
 
 			/* PLL KVCO tuning fine */
-			val = FIELD_PREP(PHYREG33_PLL_KVCO_MASK, PHYREG33_PLL_KVCO_VALUE_RK3576);
-			rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
-						 val, PHYREG33);
+			val = FIELD_PREP(RK3568_PHYREG33_PLL_KVCO_MASK,
+					 RK3576_PHYREG33_PLL_KVCO_VALUE);
+			rockchip_combphy_updatel(priv, RK3568_PHYREG33_PLL_KVCO_MASK,
+						 val, RK3568_PHYREG33);
 
 			/* Set up rx_trim: PLL LPF C1 85pf R1 1.25kohm */
-			writel(0x4c, priv->mmio + PHYREG27);
+			writel(0x4c, priv->mmio + RK3588_PHYREG27);
 
 			/*
 			 * Set up SU adjust signal:
@@ -899,20 +909,23 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
 			 * su_trim[23:16], CKRCV adjust
 			 * su_trim[31:24], CKDRV adjust
 			 */
-			writel(0x90, priv->mmio + PHYREG11);
-			writel(0x43, priv->mmio + PHYREG12);
-			writel(0x88, priv->mmio + PHYREG13);
-			writel(0x56, priv->mmio + PHYREG14);
+			writel(0x90, priv->mmio + RK3568_PHYREG11);
+			writel(0x43, priv->mmio + RK3568_PHYREG12);
+			writel(0x88, priv->mmio + RK3568_PHYREG13);
+			writel(0x56, priv->mmio + RK3568_PHYREG14);
 		} else if (priv->type == PHY_TYPE_SATA) {
 			/* downward spread spectrum +500ppm */
-			val = FIELD_PREP(PHYREG32_SSC_DIR_MASK, PHYREG32_SSC_DOWNWARD);
-			val |= FIELD_PREP(PHYREG32_SSC_OFFSET_MASK, PHYREG32_SSC_OFFSET_500PPM);
-			rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, val, PHYREG32);
+			val = FIELD_PREP(RK3568_PHYREG32_SSC_DIR_MASK,
+					 RK3568_PHYREG32_SSC_DOWNWARD);
+			val |= FIELD_PREP(RK3568_PHYREG32_SSC_OFFSET_MASK,
+					  RK3568_PHYREG32_SSC_OFFSET_500PPM);
+			rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val,
+						 RK3568_PHYREG32);
 
 			/* ssc ppm adjust to 3500ppm */
-			rockchip_combphy_updatel(priv, PHYREG10_SSC_PCM_MASK,
-						 PHYREG10_SSC_PCM_3500PPM,
-						 PHYREG10);
+			rockchip_combphy_updatel(priv, RK3576_PHYREG10_SSC_PCM_MASK,
+						 RK3576_PHYREG10_SSC_PCM_3500PPM,
+						 RK3576_PHYREG10);
 		}
 		break;
 
@@ -924,12 +937,13 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
 	if (priv->ext_refclk) {
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_ext, true);
 		if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) {
-			val = FIELD_PREP(PHYREG33_PLL_KVCO_MASK, PHYREG33_PLL_KVCO_VALUE_RK3576);
-			rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
-						 val, PHYREG33);
+			val = FIELD_PREP(RK3568_PHYREG33_PLL_KVCO_MASK,
+					 RK3576_PHYREG33_PLL_KVCO_VALUE);
+			rockchip_combphy_updatel(priv, RK3568_PHYREG33_PLL_KVCO_MASK,
+						 val, RK3568_PHYREG33);
 
 			/* Set up rx_trim: PLL LPF C1 85pf R1 2.5kohm */
-			writel(0x0c, priv->mmio + PHYREG27);
+			writel(0x0c, priv->mmio + RK3588_PHYREG27);
 
 			/*
 			 * Set up SU adjust signal:
@@ -939,25 +953,25 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
 			 * su_trim[23:16], CKRCV adjust
 			 * su_trim[31:24], CKDRV adjust
 			 */
-			writel(0x90, priv->mmio + PHYREG11);
-			writel(0x43, priv->mmio + PHYREG12);
-			writel(0x88, priv->mmio + PHYREG13);
-			writel(0x56, priv->mmio + PHYREG14);
+			writel(0x90, priv->mmio + RK3568_PHYREG11);
+			writel(0x43, priv->mmio + RK3568_PHYREG12);
+			writel(0x88, priv->mmio + RK3568_PHYREG13);
+			writel(0x56, priv->mmio + RK3568_PHYREG14);
 		}
 	}
 
 	if (priv->enable_ssc) {
-		val = readl(priv->mmio + PHYREG8);
-		val |= PHYREG8_SSC_EN;
-		writel(val, priv->mmio + PHYREG8);
+		val = readl(priv->mmio + RK3568_PHYREG8);
+		val |= RK3568_PHYREG8_SSC_EN;
+		writel(val, priv->mmio + RK3568_PHYREG8);
 
 		if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_24MHz) {
 			/* Set PLL loop divider */
-			writel(0x00, priv->mmio + PHYREG17);
-			writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18);
+			writel(0x00, priv->mmio + RK3576_PHYREG17);
+			writel(RK3568_PHYREG18_PLL_LOOP, priv->mmio + RK3568_PHYREG18);
 
 			/* Set up rx_pck invert and rx msb to disable */
-			writel(0x00, priv->mmio + PHYREG27);
+			writel(0x00, priv->mmio + RK3588_PHYREG27);
 
 			/*
 			 * Set up SU adjust signal:
@@ -966,16 +980,17 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
 			 * su_trim[23:16], CKRCV adjust
 			 * su_trim[31:24], CKDRV adjust
 			 */
-			writel(0x90, priv->mmio + PHYREG11);
-			writel(0x02, priv->mmio + PHYREG12);
-			writel(0x08, priv->mmio + PHYREG13);
-			writel(0x57, priv->mmio + PHYREG14);
-			writel(0x40, priv->mmio + PHYREG15);
+			writel(0x90, priv->mmio + RK3568_PHYREG11);
+			writel(0x02, priv->mmio + RK3568_PHYREG12);
+			writel(0x08, priv->mmio + RK3568_PHYREG13);
+			writel(0x57, priv->mmio + RK3568_PHYREG14);
+			writel(0x40, priv->mmio + RK3568_PHYREG15);
 
-			writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
+			writel(RK3568_PHYREG16_SSC_CNT_VALUE, priv->mmio + RK3568_PHYREG16);
 
-			val = FIELD_PREP(PHYREG33_PLL_KVCO_MASK, PHYREG33_PLL_KVCO_VALUE_RK3576);
-			writel(val, priv->mmio + PHYREG33);
+			val = FIELD_PREP(RK3568_PHYREG33_PLL_KVCO_MASK,
+					 RK3576_PHYREG33_PLL_KVCO_VALUE);
+			writel(val, priv->mmio + RK3568_PHYREG33);
 		}
 	}
 
@@ -1045,30 +1060,28 @@ static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv)
 		break;
 	case PHY_TYPE_USB3:
 		/* Set SSC downward spread spectrum */
-		rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK,
-					 PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT,
-					 PHYREG32);
+		val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
+		rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
 
 		/* Enable adaptive CTLE for USB3.0 Rx. */
-		val = readl(priv->mmio + PHYREG15);
-		val |= PHYREG15_CTLE_EN;
-		writel(val, priv->mmio + PHYREG15);
+		val = readl(priv->mmio + RK3568_PHYREG15);
+		val |= RK3568_PHYREG15_CTLE_EN;
+		writel(val, priv->mmio + RK3568_PHYREG15);
 
 		/* Set PLL KVCO fine tuning signals. */
-		rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
-					 PHYREG33_PLL_KVCO_VALUE << PHYREG33_PLL_KVCO_SHIFT,
-					 PHYREG33);
+		val = RK3568_PHYREG33_PLL_KVCO_VALUE << RK3568_PHYREG33_PLL_KVCO_SHIFT,
+		rockchip_combphy_updatel(priv, RK3568_PHYREG33_PLL_KVCO_MASK, val, RK3568_PHYREG33);
 
 		/* Enable controlling random jitter. */
-		writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12);
+		writel(RK3568_PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + RK3568_PHYREG12);
 
 		/* Set PLL input clock divider 1/2. */
-		rockchip_combphy_updatel(priv, PHYREG6_PLL_DIV_MASK,
-					 PHYREG6_PLL_DIV_2 << PHYREG6_PLL_DIV_SHIFT,
-					 PHYREG6);
+		rockchip_combphy_updatel(priv, RK3568_PHYREG6_PLL_DIV_MASK,
+					 RK3568_PHYREG6_PLL_DIV_2 << RK3568_PHYREG6_PLL_DIV_SHIFT,
+					 RK3568_PHYREG6);
 
-		writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18);
-		writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11);
+		writel(RK3568_PHYREG18_PLL_LOOP, priv->mmio + RK3568_PHYREG18);
+		writel(RK3568_PHYREG11_SU_TRIM_0_7, priv->mmio + RK3568_PHYREG11);
 
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txelec_sel, false);
@@ -1076,16 +1089,16 @@ static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv)
 		break;
 	case PHY_TYPE_SATA:
 		/* Enable adaptive CTLE for SATA Rx. */
-		val = readl(priv->mmio + PHYREG15);
-		val |= PHYREG15_CTLE_EN;
-		writel(val, priv->mmio + PHYREG15);
+		val = readl(priv->mmio + RK3568_PHYREG15);
+		val |= RK3568_PHYREG15_CTLE_EN;
+		writel(val, priv->mmio + RK3568_PHYREG15);
 		/*
 		 * Set tx_rterm=50ohm and rx_rterm=44ohm for SATA.
 		 * 0: 60ohm, 8: 50ohm 15: 44ohm (by step abort 1ohm)
 		 */
-		val = PHYREG7_TX_RTERM_50OHM << PHYREG7_TX_RTERM_SHIFT;
-		val |= PHYREG7_RX_RTERM_44OHM << PHYREG7_RX_RTERM_SHIFT;
-		writel(val, priv->mmio + PHYREG7);
+		val = RK3568_PHYREG7_TX_RTERM_50OHM << RK3568_PHYREG7_TX_RTERM_SHIFT;
+		val |= RK3568_PHYREG7_RX_RTERM_44OHM << RK3568_PHYREG7_RX_RTERM_SHIFT;
+		writel(val, priv->mmio + RK3568_PHYREG7);
 
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_sata, true);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_sata, true);
@@ -1107,11 +1120,11 @@ static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv)
 	case REF_CLOCK_24MHz:
 		if (priv->type == PHY_TYPE_USB3 || priv->type == PHY_TYPE_SATA) {
 			/* Set ssc_cnt[9:0]=0101111101 & 31.5KHz. */
-			val = PHYREG15_SSC_CNT_VALUE << PHYREG15_SSC_CNT_SHIFT;
-			rockchip_combphy_updatel(priv, PHYREG15_SSC_CNT_MASK,
-						 val, PHYREG15);
+			val = RK3568_PHYREG15_SSC_CNT_VALUE << RK3568_PHYREG15_SSC_CNT_SHIFT;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG15_SSC_CNT_MASK,
+						 val, RK3568_PHYREG15);
 
-			writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
+			writel(RK3568_PHYREG16_SSC_CNT_VALUE, priv->mmio + RK3568_PHYREG16);
 		}
 		break;
 
@@ -1122,23 +1135,25 @@ static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv)
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_100m, true);
 		if (priv->type == PHY_TYPE_PCIE) {
 			/* PLL KVCO fine tuning. */
-			val = 4 << PHYREG33_PLL_KVCO_SHIFT;
-			rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
-						 val, PHYREG33);
+			val = 4 << RK3568_PHYREG33_PLL_KVCO_SHIFT;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG33_PLL_KVCO_MASK,
+						 val, RK3568_PHYREG33);
 
 			/* Enable controlling random jitter. */
-			writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12);
+			writel(RK3568_PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + RK3568_PHYREG12);
 
 			/* Set up rx_trim: PLL LPF C1 85pf R1 1.25kohm */
-			writel(PHYREG27_RX_TRIM_RK3588, priv->mmio + PHYREG27);
+			writel(RK3588_PHYREG27_RX_TRIM, priv->mmio + RK3588_PHYREG27);
 
 			/* Set up su_trim:  */
-			writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11);
+			writel(RK3568_PHYREG11_SU_TRIM_0_7, priv->mmio + RK3568_PHYREG11);
 		} else if (priv->type == PHY_TYPE_SATA) {
 			/* downward spread spectrum +500ppm */
-			val = PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT;
-			val |= PHYREG32_SSC_OFFSET_500PPM << PHYREG32_SSC_OFFSET_SHIFT;
-			rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, val, PHYREG32);
+			val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
+			val |= RK3568_PHYREG32_SSC_OFFSET_500PPM <<
+			       RK3568_PHYREG32_SSC_OFFSET_SHIFT;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val,
+						 RK3568_PHYREG32);
 		}
 		break;
 	default:
@@ -1149,20 +1164,21 @@ static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv)
 	if (priv->ext_refclk) {
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_ext, true);
 		if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) {
-			val = PHYREG13_RESISTER_HIGH_Z << PHYREG13_RESISTER_SHIFT;
-			val |= PHYREG13_CKRCV_AMP0;
-			rockchip_combphy_updatel(priv, PHYREG13_RESISTER_MASK, val, PHYREG13);
-
-			val = readl(priv->mmio + PHYREG14);
-			val |= PHYREG14_CKRCV_AMP1;
-			writel(val, priv->mmio + PHYREG14);
+			val = RK3568_PHYREG13_RESISTER_HIGH_Z << RK3568_PHYREG13_RESISTER_SHIFT;
+			val |= RK3568_PHYREG13_CKRCV_AMP0;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG13_RESISTER_MASK, val,
+						 RK3568_PHYREG13);
+
+			val = readl(priv->mmio + RK3568_PHYREG14);
+			val |= RK3568_PHYREG14_CKRCV_AMP1;
+			writel(val, priv->mmio + RK3568_PHYREG14);
 		}
 	}
 
 	if (priv->enable_ssc) {
-		val = readl(priv->mmio + PHYREG8);
-		val |= PHYREG8_SSC_EN;
-		writel(val, priv->mmio + PHYREG8);
+		val = readl(priv->mmio + RK3568_PHYREG8);
+		val |= RK3568_PHYREG8_SSC_EN;
+		writel(val, priv->mmio + RK3568_PHYREG8);
 	}
 
 	return 0;
Signature · 1 line
2.50.1
author
#5 lore raw

PATCH v5 5/6 phy: rockchip: naneng-combphy: Add RK3528 support

In reply to Yao Zi

Rockchip RK3528 integrates one naneng-combphy that is able to operate in PCIe and USB3 mode. The control logic is similar to previous variants of naneng-combphy but the register layout is apperantly different from the RK3568 one.

---
 .../rockchip/phy-rockchip-naneng-combphy.c    | 189 +++++++++++++++++-
 1 file changed, 188 insertions(+), 1 deletion(-)
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +188 -1
index ce84166cd772..0d25872e6712 100644
@@ -20,7 +20,46 @@
 #define REF_CLOCK_25MHz			(25 * HZ_PER_MHZ)
 #define REF_CLOCK_100MHz		(100 * HZ_PER_MHZ)
 
-/* COMBO PHY REG */
+/* RK3528 COMBO PHY REG */
+#define RK3528_PHYREG6				0x18
+#define RK3528_PHYREG6_PLL_KVCO			GENMASK(12, 10)
+#define RK3528_PHYREG6_PLL_KVCO_VALUE		0x2
+#define RK3528_PHYREG6_SSC_DIR			GENMASK(5, 4)
+#define RK3528_PHYREG6_SSC_UPWARD		0
+#define RK3528_PHYREG6_SSC_DOWNWARD		1
+
+#define RK3528_PHYREG40				0x100
+#define RK3528_PHYREG40_SSC_EN			BIT(20)
+#define RK3528_PHYREG40_SSC_CNT			GENMASK(10, 0)
+#define RK3528_PHYREG40_SSC_CNT_VALUE		0x17d
+
+#define RK3528_PHYREG42				0x108
+#define RK3528_PHYREG42_CKDRV_CLK_SEL		BIT(29)
+#define RK3528_PHYREG42_CKDRV_CLK_PLL		0
+#define RK3528_PHYREG42_CKDRV_CLK_CKRCV		1
+#define RK3528_PHYREG42_PLL_LPF_R1_ADJ		GENMASK(10, 7)
+#define RK3528_PHYREG42_PLL_LPF_R1_ADJ_VALUE	0x9
+#define RK3528_PHYREG42_PLL_CHGPUMP_CUR_ADJ	GENMASK(6, 4)
+#define RK3528_PHYREG42_PLL_CHGPUMP_CUR_ADJ_VALUE 0x7
+#define RK3528_PHYREG42_PLL_KVCO_ADJ		GENMASK(2, 0)
+#define RK3528_PHYREG42_PLL_KVCO_ADJ_VALUE	0x0
+
+#define RK3528_PHYREG80				0x200
+#define RK3528_PHYREG80_CTLE_EN			BIT(17)
+
+#define RK3528_PHYREG81				0x204
+#define RK3528_PHYREG81_CDR_PHASE_PATH_GAIN_2X	BIT(5)
+#define RK3528_PHYREG81_SLEW_RATE_CTRL		GENMASK(2, 0)
+#define RK3528_PHYREG81_SLEW_RATE_CTRL_SLOW	0x7
+
+#define RK3528_PHYREG83				0x20c
+#define RK3528_PHYREG83_RX_SQUELCH		GENMASK(2, 0)
+#define RK3528_PHYREG83_RX_SQUELCH_VALUE	0x6
+
+#define RK3528_PHYREG86				0x218
+#define RK3528_PHYREG86_RTERM_DET_CLK_EN	BIT(14)
+
+/* RK3568 COMBO PHY REG */
 #define RK3568_PHYREG6				0x14
 #define RK3568_PHYREG6_PLL_DIV_MASK		GENMASK(7, 6)
 #define RK3568_PHYREG6_PLL_DIV_SHIFT		6
@@ -400,6 +439,150 @@ static int rockchip_combphy_probe(struct platform_device *pdev)
 	return PTR_ERR_OR_ZERO(phy_provider);
 }
 
+static int rk3528_combphy_cfg(struct rockchip_combphy_priv *priv)
+{
+	const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
+	unsigned long rate;
+	u32 val;
+
+	/* Set SSC downward spread spectrum */
+	val = FIELD_PREP(RK3528_PHYREG6_SSC_DIR, RK3528_PHYREG6_SSC_DOWNWARD);
+	rockchip_combphy_updatel(priv, RK3528_PHYREG6_SSC_DIR, val, RK3528_PHYREG6);
+
+	switch (priv->type) {
+	case PHY_TYPE_PCIE:
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_pcie, true);
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_pcie, true);
+		break;
+	case PHY_TYPE_USB3:
+		/* Enable adaptive CTLE for USB3.0 Rx */
+		rockchip_combphy_updatel(priv, RK3528_PHYREG80_CTLE_EN, RK3528_PHYREG80_CTLE_EN,
+					 RK3528_PHYREG80);
+
+		/* Set slow slew rate control for PI */
+		val = FIELD_PREP(RK3528_PHYREG81_SLEW_RATE_CTRL,
+				 RK3528_PHYREG81_SLEW_RATE_CTRL_SLOW);
+		rockchip_combphy_updatel(priv, RK3528_PHYREG81_SLEW_RATE_CTRL, val,
+					 RK3528_PHYREG81);
+
+		/* Set CDR phase path with 2x gain */
+		rockchip_combphy_updatel(priv, RK3528_PHYREG81_CDR_PHASE_PATH_GAIN_2X,
+					 RK3528_PHYREG81_CDR_PHASE_PATH_GAIN_2X, RK3528_PHYREG81);
+
+		/* Set Rx squelch input filler bandwidth */
+		val = FIELD_PREP(RK3528_PHYREG83_RX_SQUELCH, RK3528_PHYREG83_RX_SQUELCH_VALUE);
+		rockchip_combphy_updatel(priv, RK3528_PHYREG83_RX_SQUELCH, val, RK3528_PHYREG83);
+
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false);
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txelec_sel, false);
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->usb_mode_set, true);
+		rockchip_combphy_param_write(priv->pipe_grf, &cfg->u3otg0_port_en, true);
+		break;
+	default:
+		dev_err(priv->dev, "incompatible PHY type\n");
+		return -EINVAL;
+	}
+
+	rate = clk_get_rate(priv->refclk);
+
+	switch (rate) {
+	case REF_CLOCK_24MHz:
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_24m, true);
+		if (priv->type == PHY_TYPE_USB3) {
+			/* Set ssc_cnt[10:0]=00101111101 & 31.5KHz */
+			val = FIELD_PREP(RK3528_PHYREG40_SSC_CNT, RK3528_PHYREG40_SSC_CNT_VALUE);
+			rockchip_combphy_updatel(priv, RK3528_PHYREG40_SSC_CNT, val,
+						 RK3528_PHYREG40);
+		} else if (priv->type == PHY_TYPE_PCIE) {
+			/* tx_trim[14]=1, Enable the counting clock of the rterm detect */
+			rockchip_combphy_updatel(priv, RK3528_PHYREG86_RTERM_DET_CLK_EN,
+						 RK3528_PHYREG86_RTERM_DET_CLK_EN, RK3528_PHYREG86);
+		}
+		break;
+	case REF_CLOCK_100MHz:
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_100m, true);
+		if (priv->type == PHY_TYPE_PCIE) {
+			/* PLL KVCO tuning fine */
+			val = FIELD_PREP(RK3528_PHYREG6_PLL_KVCO, RK3528_PHYREG6_PLL_KVCO_VALUE);
+			rockchip_combphy_updatel(priv, RK3528_PHYREG6_PLL_KVCO, val,
+						 RK3528_PHYREG6);
+
+			/* su_trim[6:4]=111, [10:7]=1001, [2:0]=000, swing 650mv */
+			writel(0x570804f0, priv->mmio + RK3528_PHYREG42);
+		}
+		break;
+	default:
+		dev_err(priv->dev, "Unsupported rate: %lu\n", rate);
+		return -EINVAL;
+	}
+
+	if (device_property_read_bool(priv->dev, "rockchip,ext-refclk")) {
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_ext, true);
+
+		if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) {
+			val = FIELD_PREP(RK3528_PHYREG42_CKDRV_CLK_SEL,
+					 RK3528_PHYREG42_CKDRV_CLK_CKRCV);
+			val |= FIELD_PREP(RK3528_PHYREG42_PLL_LPF_R1_ADJ,
+					  RK3528_PHYREG42_PLL_LPF_R1_ADJ_VALUE);
+			val |= FIELD_PREP(RK3528_PHYREG42_PLL_CHGPUMP_CUR_ADJ,
+					  RK3528_PHYREG42_PLL_CHGPUMP_CUR_ADJ_VALUE);
+			val |= FIELD_PREP(RK3528_PHYREG42_PLL_KVCO_ADJ,
+					  RK3528_PHYREG42_PLL_KVCO_ADJ_VALUE);
+			rockchip_combphy_updatel(priv,
+						 RK3528_PHYREG42_CKDRV_CLK_SEL		|
+						 RK3528_PHYREG42_PLL_LPF_R1_ADJ		|
+						 RK3528_PHYREG42_PLL_CHGPUMP_CUR_ADJ	|
+						 RK3528_PHYREG42_PLL_KVCO_ADJ,
+						 val, RK3528_PHYREG42);
+
+			val = FIELD_PREP(RK3528_PHYREG6_PLL_KVCO, RK3528_PHYREG6_PLL_KVCO_VALUE);
+			rockchip_combphy_updatel(priv, RK3528_PHYREG6_PLL_KVCO, val,
+						 RK3528_PHYREG6);
+		}
+	}
+
+	if (priv->type == PHY_TYPE_PCIE) {
+		if (device_property_read_bool(priv->dev, "rockchip,enable-ssc"))
+			rockchip_combphy_updatel(priv, RK3528_PHYREG40_SSC_EN,
+						 RK3528_PHYREG40_SSC_EN, RK3528_PHYREG40);
+	}
+
+	return 0;
+}
+
+static const struct rockchip_combphy_grfcfg rk3528_combphy_grfcfgs = {
+	/* pipe-phy-grf */
+	.pcie_mode_set		= { 0x0000, 5, 0, 0x00, 0x11 },
+	.usb_mode_set		= { 0x0000, 5, 0, 0x00, 0x04 },
+	.pipe_rxterm_set	= { 0x0000, 12, 12, 0x00, 0x01 },
+	.pipe_txelec_set	= { 0x0004, 1, 1, 0x00, 0x01 },
+	.pipe_txcomp_set	= { 0x0004, 4, 4, 0x00, 0x01 },
+	.pipe_clk_24m		= { 0x0004, 14, 13, 0x00, 0x00 },
+	.pipe_clk_100m		= { 0x0004, 14, 13, 0x00, 0x02 },
+	.pipe_rxterm_sel	= { 0x0008, 8, 8, 0x00, 0x01 },
+	.pipe_txelec_sel	= { 0x0008, 12, 12, 0x00, 0x01 },
+	.pipe_txcomp_sel	= { 0x0008, 15, 15, 0x00, 0x01 },
+	.pipe_clk_ext		= { 0x000c, 9, 8, 0x02, 0x01 },
+	.pipe_phy_status	= { 0x0034, 6, 6, 0x01, 0x00 },
+	.con0_for_pcie		= { 0x0000, 15, 0, 0x00, 0x110 },
+	.con1_for_pcie		= { 0x0004, 15, 0, 0x00, 0x00 },
+	.con2_for_pcie		= { 0x0008, 15, 0, 0x00, 0x101 },
+	.con3_for_pcie		= { 0x000c, 15, 0, 0x00, 0x0200 },
+	/* pipe-grf */
+	.u3otg0_port_en         = { 0x0044, 15, 0, 0x0181, 0x1100 },
+};
+
+static const struct rockchip_combphy_cfg rk3528_combphy_cfgs = {
+	.num_phys	= 1,
+	.phy_ids	= {
+		0xffdc0000,
+	},
+	.grfcfg		= &rk3528_combphy_grfcfgs,
+	.combphy_cfg	= rk3528_combphy_cfg,
+};
+
 static int rk3562_combphy_cfg(struct rockchip_combphy_priv *priv)
 {
 	const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
@@ -1225,6 +1408,10 @@ static const struct rockchip_combphy_cfg rk3588_combphy_cfgs = {
 };
 
 static const struct of_device_id rockchip_combphy_of_match[] = {
+	{
+		.compatible = "rockchip,rk3528-naneng-combphy",
+		.data = &rk3528_combphy_cfgs,
+	},
 	{
 		.compatible = "rockchip,rk3562-naneng-combphy",
 		.data = &rk3562_combphy_cfgs,
Signature · 1 line
2.50.1
#6 lore raw

Re: [PATCH v5 5/6] phy: rockchip: naneng-combphy: Add RK3528 support

Hi,

Quoted 4 lines

Rockchip RK3528 integrates one naneng-combphy that is able to operate in PCIe and USB3 mode. The control logic is similar to previous variants of naneng-combphy but the register layout is apperantly different from the RK3568 one.

Is this a typo? apperantly -> apparently

Thanks,
Chukun

--
2.25.1

author
#7 lore raw

Re: [PATCH v5 5/6] phy: rockchip: naneng-combphy: Add RK3528 support

Quoted 8 lines · Chukun Pan

Hi,

Quoted 4 lines

Rockchip RK3528 integrates one naneng-combphy that is able to operate in PCIe and USB3 mode. The control logic is similar to previous variants of naneng-combphy but the register layout is apperantly different from the RK3568 one.

Is this a typo? apperantly -> apparently

Ahh, yes, thanks for catching it.

I think this series (at least the binding and driver parts) is mostly ready for merging, so I'll be thankful if the maintainer could fix it while picking up, or I will carry the fix in a new version if it's found that larger changes are necessary.

Quoted 2 lines

Thanks,
Chukun

Best regards,
Yao Zi

Quoted 4 lines

--
2.25.1

author
#8 lore raw

PATCH v5 6/6 arm64: dts: rockchip: Add naneng-combphy for RK3528

In reply to Yao Zi

Rockchip RK3528 ships a naneng-combphy that is shared by PCIe and USB 3.0 controllers. Describe it and the pipe-phy grf which it depends on.

---
 arch/arm64/boot/dts/rockchip/rk3528.dtsi | 24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)
arch/arm64/boot/dts/rockchip/rk3528.dtsi +24 -0
index 54fa8089c4d3..58c8977249be 100644
@@ -417,6 +417,11 @@ vpu_grf: syscon@ff340000 {
 			reg = <0x0 0xff340000 0x0 0x8000>;
 		};
 
+		pipe_phy_grf: syscon@ff348000 {
+			compatible = "rockchip,rk3528-pipe-phy-grf", "syscon";
+			reg = <0x0 0xff348000 0x0 0x8000>;
+		};
+
 		vo_grf: syscon@ff360000 {
 			compatible = "rockchip,rk3528-vo-grf", "syscon";
 			reg = <0x0 0xff360000 0x0 0x10000>;
@@ -1085,6 +1090,25 @@ dmac: dma-controller@ffd60000 {
 			#dma-cells = <1>;
 			arm,pl330-periph-burst;
 		};
+
+		combphy: phy@ffdc0000 {
+			compatible = "rockchip,rk3528-naneng-combphy";
+			reg = <0x0 0xffdc0000 0x0 0x10000>;
+			assigned-clocks = <&cru CLK_REF_PCIE_INNER_PHY>;
+			assigned-clock-rates = <100000000>;
+			clocks = <&cru CLK_REF_PCIE_INNER_PHY>,
+				 <&cru PCLK_PCIE_PHY>,
+				 <&cru PCLK_PIPE_GRF>;
+			clock-names = "ref", "apb", "pipe";
+			power-domains = <&power RK3528_PD_VPU>;
+			resets = <&cru SRST_PCIE_PIPE_PHY>,
+				 <&cru SRST_P_PCIE_PHY>;
+			reset-names = "phy", "apb";
+			#phy-cells = <1>;
+			rockchip,pipe-grf = <&vpu_grf>;
+			rockchip,pipe-phy-grf = <&pipe_phy_grf>;
+			status = "disabled";
+		};
 	};
 };
 
Signature · 1 line
2.50.1
maintainer Applied
#9 lore raw

Re: (subset) [PATCH v5 0/6] Support RK3528 variant of Rockchip naneng-combphy

In reply to Yao Zi
Quoted 8 lines · Yao Zi

Rockchip RK3528 ships a naneng-combphy that operates in either PCIe or USB 3.0 mode. It has a similar control logic to previous generations of naneng-combphy but an apparently different register layout.

This series prepares phy-rockchip-naneng-combphy.c for variants with a different register layout and add RK3528 support.

[...]

Applied, thanks!

[1/6] dt-bindings: soc: rockchip: Add RK3528 pipe-phy GRF syscon

      commit: d7122636eca216ea2876baae45483d17e40a55f6
[2/6] dt-bindings: phy: rockchip: naneng-combphy: Add power-domains property
      commit: 19bb2bfdfa5dc4a912e7e5e3432290204e998ac9
[3/6] dt-bindings: phy: rockchip: naneng-combphy: Add RK3528 variant
      commit: d9e0fd60d8d44b2cabd41f5e370e9d41edffe6e9
[4/6] phy: rockchip: naneng-combphy: Add SoC prefix to register definitions
      commit: 11f1896e60f61ca1948cb7920585a79ce5254c0c
[5/6] phy: rockchip: naneng-combphy: Add RK3528 support
      commit: aee07ee1b97d9a3825e8db609a1c76157218cc59

Best regards,

Signature · 1 line
~Vinod
maintainer Applied
#10 lore raw

Re: (subset) [PATCH v5 0/6] Support RK3528 variant of Rockchip naneng-combphy

In reply to Yao Zi
Quoted 8 lines · Yao Zi

Rockchip RK3528 ships a naneng-combphy that operates in either PCIe or USB 3.0 mode. It has a similar control logic to previous generations of naneng-combphy but an apparently different register layout.

This series prepares phy-rockchip-naneng-combphy.c for variants with a different register layout and add RK3528 support.

[...]

Applied, thanks!

[6/6] arm64: dts: rockchip: Add naneng-combphy for RK3528

      commit: 70bb21cbc8c704c664b5d3ea417f3e35376fc229

Best regards,

Signature · 1 line
Heiko Stuebner <[email protected]>