Add support for NetCube Systems OpenNMC (dobermann)
Subsystems (3)
v2 cover Add support for NetCube Systems OpenNMC (dobermann)
This series adds support for the NetCube Systems OpenNMC
Changes in v2:
- fixed ordering of compatible enum
- fixed gpio line names
---
Lukas Schmid (3):
dt-bindings: arm: sunxi: Add NetCube Systems OpenNMC (dobermann)
riscv: dts: allwinner: d1s-t113: Add uart4 pinctrl required by NetCube
Systems OpenNMC
ARM: dts: sunxi: add support for NetCube Systems OpenNMC (dobermann)
.../devicetree/bindings/arm/sunxi.yaml | 1 + .../sun8i-t113s-netcube-dobermann.dts | 149 ++++++++++++++++++ .../boot/dts/allwinner/sunxi-d1s-t113.dtsi | 6 + 3 files changed, 156 insertions(+) create mode 100644 arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-dobermann.dts
Signature · 1 line
2.47.3
PATCH v2 1/3 dt-bindings: arm: sunxi: Add NetCube Systems OpenNMC (dobermann)
The OpenNMC is an open replacement for APC SmartSlot management cards based on the Nagami System-on-Module.
--- Documentation/devicetree/bindings/arm/sunxi.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/arm/sunxi.yaml +1 -0
@@ -598,6 +598,7 @@ properties: - description: NetCube Systems Nagami SoM based boards items: - enum: + - netcube,dobermann - netcube,nagami-basic-carrier - netcube,nagami-keypad-carrier - const: netcube,nagami
Signature · 1 line
2.47.3
Re: [PATCH v2 1/3] dt-bindings: arm: sunxi: Add NetCube Systems OpenNMC (dobermann)
pw-bot: not-applicable
PATCH v2 2/3 riscv: dts: allwinner: d1s-t113: Add uart4 pinctrl required by NetCube Systems OpenNMC
In reply to Lukas SchmidAdded the "uart4_pb_pins" pinctrl used by the OpenNMC
--- arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi | 6 ++++++ 1 file changed, 6 insertions(+)
arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi +6 -0
@@ -191,6 +191,12 @@ uart3_pb_pins: uart3-pb-pins { pins = "PB6", "PB7"; function = "uart3"; }; + + /omit-if-no-ref/ + uart4_pb_pins: uart4-pb-pins { + pins = "PB2", "PB3"; + function = "uart4"; + }; }; ccu: clock-controller@2001000 {
Signature · 1 line
2.47.3
PATCH v2 3/3 ARM: dts: sunxi: add support for NetCube Systems OpenNMC (dobermann)
In reply to Lukas SchmidNetCube Systems OpenNMC is an open replacement for APC SmartSlot Management Cards. It is based on the Nagami System-on-Module. It breaks out the following interfaces:
- 10/100 Mbps Ethernet
- USB Type-C OTG using a TUSB320 (usb0)
- USB Type-C Console Port using a CH340 (uart3)
- USB Type-A Host with internal CH334 USB-Hub (usb1)
- MicroSD Slot with Card-Detect (mmc0)
- WiFi/Bluetooth using the modules built-in ESP32
- SmartSlot serial interface (uart4)
- DS3232 RTC with CR1220 Battery Backup
- Extension connector providing SPI,I2C,USB,CAN,UART for future use.
--- .../sun8i-t113s-netcube-dobermann.dts | 149 ++++++++++++++++++ 1 file changed, 149 insertions(+) create mode 100644 arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-dobermann.dts
arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-dobermann.dts new file +149 -0
@@ -0,0 +1,149 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2026 Lukas Schmid <[email protected]> + */ + +/dts-v1/; +#include "sun8i-t113s-netcube-nagami.dtsi" + +#include <dt-bindings/leds/common.h> + +/ { + model = "NetCube Systems OpenNMC (dobermann)"; + compatible = "netcube,dobermann", "netcube,nagami", + "allwinner,sun8i-t113s"; + + aliases { + serial2 = &uart4; // UART on SmartSlot + rtc0 = &ds3232; + rtc1 = &rtc; // not battery backed + }; + + leds { + compatible = "gpio-leds"; + + led_heartbeat_green: led-heartbeat-green { + gpios = <&pio 6 14 GPIO_ACTIVE_HIGH>; /* PG14 */ + linux,default-trigger = "heartbeat"; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_HEARTBEAT; + }; + }; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&i2c2 { + status = "okay"; + + tusb320: typec@60 { + compatible = "ti,tusb320"; + reg = <0x60>; + interrupts-extended = <&pio 3 22 IRQ_TYPE_LEVEL_LOW>; /* PD22 */ + }; + + ds3232: rtc@68 { + compatible = "dallas,ds3232"; + reg = <0x68>; + }; +}; + +/* microSD Card Slot on the board */ +&mmc0 { + vmmc-supply = <®_vcc3v3>; + disable-wp; + bus-width = <4>; + cd-gpios = <&pio 6 15 GPIO_ACTIVE_LOW>; /* PG15 */ + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&pio { + gpio-line-names = "", "", "", "", // PA + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "SMART_TX", "SMART_RX", // PB + "EXT_IO3", "EXT_IO2", "CONSOLE_TX", "CONSOLE_RX", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "eMMC_CLK", "eMMC_CMD", // PC + "eMMC_D2", "eMMC_D1", "eMMC_D0", "eMMC_D3", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", // PD + "", "", "", "", + "", "USB_SEC_EN", "EXT_SPI_nCS", "EXT_SPI_SCK", + "EXT_SPI_MOSI", "EXT_SPI_MISO", "EXT_IO5", "EXT_IO4", + "SMART_SEL", "", "", "", + "I2C2_SCL", "I2C2_SDA", "TUSB320_nINT", "", + "", "", "", "", + "", "", "", "", + "ETH_CRSDV", "ETH_RXD0", "ETH_RXD1", "ETH_TXCK", // PE + "ETH_TXD0", "ETH_TXD1", "ETH_TXEN", "", + "ETH_MDC", "ETH_MDIO", "I2C3_nINT", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "uSD_D1", "uSD_D0", "uSD_CLK", "uSD_CMD", // PF + "uSD_D3", "uSD_D2", "TUSB320_ID", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "ESP_CLK", "ESP_CMD", "ESP_D0", "ESP_D1", // PG + "ESP_D2", "ESP_D3", "ESP_TXD", "ESP_RXD", + "ESP_nBOOT", "ESP_nRST", "I2C3_SCL", "I2C3_SDA", + "EXT_IO1", "EXT_IO0", "LED_HEARTBEAT", "SD_DETECT", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", ""; +}; + +/* SmartSlot serial */ +&uart4 { + pinctrl-0 = <&uart4_pb_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&usb_otg { + extcon = <&tusb320 0>; + dr_mode = "otg"; + status = "okay"; +}; + +&usbphy { + usb0_id_det-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ + status = "okay"; +};
Signature · 1 line
2.47.3
[email protected]
AI reviewRe: [PATCH v2 3/3] ARM: dts: sunxi: add support for NetCube Systems OpenNMC (dobermann)
Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider: - [Medium] The newly added device tree file `sun8i-t113s-netcube-dobermann.dts` is missing from the…
Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [Medium] The newly added device tree file sun8i-t113s-netcube-dobermann.dts is missing from the arch/arm/boot/dts/allwinner/Makefile. As a result, the DTB will not be compiled. --
commit 72bddd5a378aaecf47418f6e924b30fb31105d2f
Author: Lukas Schmid <[email protected]>
ARM: dts: sunxi: add support for NetCube Systems OpenNMC (dobermann)
This commit adds device tree support for the NetCube Systems OpenNMC (dobermann) board. It configures the various interfaces broken out by the Nagami SoM, including Ethernet, USB, SD card, and RTC.
arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-dobermann.dts
Quoted 5 lines
arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-dobermann.dts new file +0
-0
[Severity: Medium]
Should this new device tree file be registered inarch/arm/boot/dts/allwinner/Makefile?
Without adding sun8i-t113s-netcube-dobermann.dtb to the dtb-$(CONFIG_MACH_SUN8I) list, will the kernel build system actually compile this new device tree?
[ ... ]
Signature · 1 line
Sashiko AI review · https://sashiko.dev/#/patchset/[email protected]?part=3