Add support for NetCube Systems OpenNMC (dobermann)
Subsystems (3)
v4 cover Add support for NetCube Systems OpenNMC (dobermann)
This series adds support for the NetCube Systems OpenNMC.
Sorry for the quick resend. This v4 includes the corrected Makefile target name.
Changes in v4:
- fix the ARM Makefile target name for the new board
Changes in v3:
- actually add the Makefile changes
Changes in v2:
- fixed ordering of compatible enum
- fixed gpio line names
---
Lukas Schmid (3):
dt-bindings: arm: sunxi: Add NetCube Systems OpenNMC (dobermann)
riscv: dts: allwinner: d1s-t113: Add uart4 pinctrl required by NetCube
Systems OpenNMC
ARM: dts: sunxi: add support for NetCube Systems OpenNMC (dobermann)
.../devicetree/bindings/arm/sunxi.yaml | 1 + arch/arm/boot/dts/allwinner/Makefile | 2 + .../sun8i-t113s-netcube-dobermann.dts | 149 ++++++++++++++++++ .../boot/dts/allwinner/sunxi-d1s-t113.dtsi | 6 + 4 files changed, 158 insertions(+) create mode 100644 arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-dobermann.dts
Signature · 1 line
2.47.3
PATCH v4 1/3 dt-bindings: arm: sunxi: Add NetCube Systems OpenNMC (dobermann)
The OpenNMC is an open replacement for APC SmartSlot management cards based on the Nagami System-on-Module.
--- Documentation/devicetree/bindings/arm/sunxi.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/arm/sunxi.yaml +1 -0
@@ -598,6 +598,7 @@ properties: - description: NetCube Systems Nagami SoM based boards items: - enum: + - netcube,dobermann - netcube,nagami-basic-carrier - netcube,nagami-keypad-carrier - const: netcube,nagami
Signature · 1 line
2.47.3
Re: [PATCH v4 1/3] dt-bindings: arm: sunxi: Add NetCube Systems OpenNMC (dobermann)
Quoted 7 lines · Lukas Schmid
The OpenNMC is an open replacement for APC SmartSlot management cards based on the Nagami System-on-Module.
Signed-off-by Lukas Schmid <[email protected]>--- Documentation/devicetree/bindings/arm/sunxi.yaml | 1 + 1 file changed, 1 insertion(+)
Best regards,
Krzysztof
PATCH v4 2/3 riscv: dts: allwinner: d1s-t113: Add uart4 pinctrl required by NetCube Systems OpenNMC
In reply to Lukas SchmidAdded the "uart4_pb_pins" pinctrl used by the OpenNMC
--- arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi | 6 ++++++ 1 file changed, 6 insertions(+)
arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi +6 -0
@@ -191,6 +191,12 @@ uart3_pb_pins: uart3-pb-pins { pins = "PB6", "PB7"; function = "uart3"; }; + + /omit-if-no-ref/ + uart4_pb_pins: uart4-pb-pins { + pins = "PB2", "PB3"; + function = "uart4"; + }; }; ccu: clock-controller@2001000 {
Signature · 1 line
2.47.3
Re: [PATCH v4 2/3] riscv: dts: allwinner: d1s-t113: Add uart4 pinctrl required by NetCube Systems OpenNMC
Hi,
Quoted 1 line · Lukas Schmid
Added the "
uart4_pb_pins" pinctrl used by the OpenNMC
Checked against the datasheet:
Cheers,
Andre
Quoted 23 lines
Signed-off-by Lukas Schmid <[email protected]>--- arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi | 6 ++++++ 1 file changed, 6 insertions(+)arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi +6
-0@@ -191,6 +191,12 @@ uart3_pb_pins: uart3-pb-pins { pins = "PB6", "PB7"; function = "uart3"; }; + + /omit-if-no-ref/ + uart4_pb_pins: uart4-pb-pins { + pins = "PB2", "PB3"; + function = "uart4"; + }; }; ccu: clock-controller@2001000 {
PATCH v4 3/3 ARM: dts: sunxi: add support for NetCube Systems OpenNMC (dobermann)
In reply to Lukas SchmidNetCube Systems OpenNMC is an open replacement for APC SmartSlot Management Cards. It is based on the Nagami System-on-Module. It breaks out the following interfaces:
- 10/100 Mbps Ethernet
- USB Type-C OTG using a TUSB320 (usb0)
- USB Type-C Console Port using a CH340 (uart3)
- USB Type-A Host with internal CH334 USB-Hub (usb1)
- MicroSD Slot with Card-Detect (mmc0)
- WiFi/Bluetooth using the modules built-in ESP32
- SmartSlot serial interface (uart4)
- DS3232 RTC with CR1220 Battery Backup
- Extension connector providing SPI,I2C,USB,CAN,UART for future use.
--- arch/arm/boot/dts/allwinner/Makefile | 2 + .../sun8i-t113s-netcube-dobermann.dts | 149 ++++++++++++++++++ 2 files changed, 151 insertions(+) create mode 100644 arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-dobermann.dts
arch/arm/boot/dts/allwinner/Makefile +2 -0
@@ -201,6 +201,7 @@ DTC_FLAGS_sun8i-h3-orangepi-pc := -@ DTC_FLAGS_sun8i-h3-bananapi-m2-plus-v1.2 := -@ DTC_FLAGS_sun8i-h3-orangepi-pc-plus := -@ DTC_FLAGS_sun8i-t113s-netcube-nagami-basic-carrier := -@ +DTC_FLAGS_sun8i-t113s-netcube-dobermann := -@ DTC_FLAGS_sun8i-v3s-netcube-kumquat := -@ dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-a23-evb.dtb \
@@ -261,6 +262,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-s3-lichee-zero-plus.dtb \ sun8i-s3-pinecube.dtb \ sun8i-t113s-mangopi-mq-r-t113.dtb \ + sun8i-t113s-netcube-dobermann.dtb \ sun8i-t113s-netcube-nagami-basic-carrier.dtb \ sun8i-t113s-netcube-nagami-keypad-carrier.dtb \ sun8i-t3-cqa3t-bv3.dtb \
arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-dobermann.dts new file +149 -0
149 lines not on this page · raw message
Signature · 1 line
2.47.3
Re: [PATCH v4 3/3] ARM: dts: sunxi: add support for NetCube Systems OpenNMC (dobermann)
Dne sobota, 6. junij 2026 ob 22:54:43 Srednjeevropski poletni čas je Lukas Schmid napisal(a):
Quoted 14 lines
NetCube Systems OpenNMC is an open replacement for APC SmartSlot Management Cards. It is based on the Nagami System-on-Module. It breaks out the following interfaces:
- 10/100 Mbps Ethernet
- USB Type-C OTG using a TUSB320 (usb0)
- USB Type-C Console Port using a CH340 (uart3)
- USB Type-A Host with internal CH334 USB-Hub (usb1)
- MicroSD Slot with Card-Detect (mmc0)
- WiFi/Bluetooth using the modules built-in ESP32
- SmartSlot serial interface (uart4)
- DS3232 RTC with CR1220 Battery Backup
- Extension connector providing SPI,I2C,USB,CAN,UART for future use.
Quoted 1 line
Signed-off-by Lukas Schmid <[email protected]>
DT Check passes, so:
Best regards,
Jernej
Quoted 9 lines · Lukas Schmid
This series adds support for the NetCube Systems OpenNMC.
Sorry for the quick resend. This v4 includes the corrected
Makefiletarget name.Changes in v4:
- fix the ARMMakefiletarget name for the new board[...]
Applied to sunxi/dt-for-7.3 in sunxi, thanks!
[1/3] dt-bindings: arm: sunxi: Add NetCube Systems OpenNMC (dobermann)
https://git.kernel.org/sunxi/linux/c/9995c8146bb9 [2/3] riscv: dts: allwinner: d1s-t113: Add uart4 pinctrl required by NetCube Systems OpenNMC https://git.kernel.org/sunxi/linux/c/5b0fd777eb34 [3/3] ARM: dts: sunxi: add support for NetCube Systems OpenNMC (dobermann) https://git.kernel.org/sunxi/linux/c/9dc45b17fb85
Best regards,
Signature · 1 line
Chen-Yu Tsai <[email protected]>
Chen-Yu Tsai
maintainerQuoted 12 lines · Chen-Yu Tsai
Quoted 9 lines · Lukas Schmid
This series adds support for the NetCube Systems OpenNMC.
Sorry for the quick resend. This v4 includes the corrected
Makefiletarget name.Changes in v4:
- fix the ARMMakefiletarget name for the new board[...]
Quoted 8 lines
Applied to sunxi/dt-for-7.3 in sunxi, thanks!
[1/3] dt-bindings: arm: sunxi: Add NetCube Systems OpenNMC (dobermann)
https://git.kernel.org/sunxi/linux/c/9995c8146bb9 [2/3] riscv: dts: allwinner: d1s-t113: Add uart4 pinctrl required by NetCube Systems OpenNMC https://git.kernel.org/sunxi/linux/c/5b0fd777eb34 [3/3] ARM: dts: sunxi: add support for NetCube Systems OpenNMC (dobermann) https://git.kernel.org/sunxi/linux/c/9dc45b17fb85
Force pushed this one to change "sunxi" to "allwinner".
Quoted 6 lines
Best regards,
--
Chen-Yu Tsai <[email protected]>