Skip to contentSkip to conversation

ARM: dts: aspeed: Add Nvidia VR-NVL BMC

PATCH In review Jacky Huang 2 participants 2 messages Aug 25 – Aug 26 Arm (32-bit)

v3 of 4 In review Latest is v4 →

lore
Share & tools
lore
#0 lore raw

PATCH v3 1/1 ARM: dts: aspeed: Add Nvidia VR-NVL BMC

Adds a dts for the NVIDIA VR-NVL BMC board, an AST2600-based BMC for the Vera Rubin NVL platform.

MAC0 uses phy-mode = "rgmii-id" with no SoC-side clk-delay node, so it relies on the zero default introduced by commit 3f6198c0db1c ("clk:
ast2600: set default clk-delay for all ethernet macs to 0"). With that change in place, MAC0 brings up its MDIO bus and establishes a link with the on-board PHY.

---
v3:
- Drop unused spi1/spi2 aliases and nodes.
- Drop unused FMC flash@1 and flash@2.

v2:
- Sort the Makefile entry alphabetically.
- Drop unused mmc0/1/2 aliases; eMMC/SD are not used on this board.
- Drop unused ethernet1/2/3 aliases (only mac0 is enabled).
- Drop redundant aspeed,ecc-size-mb = <0> (defaults to 0).
- Drop unnecessary flash compatible; it defaults to jedec,spi-nor.
- Drop the disabled spi1 flash@1 node.

v2: Message-Id: <[email protected]>
v1: Message-Id: <[email protected]>

 arch/arm/dts/Makefile                  |   1 +
 arch/arm/dts/ast2600-vr-bmc-nvidia.dts | 155 +++++++++++++++++++++++++
 2 files changed, 156 insertions(+)
 create mode 100644 arch/arm/dts/ast2600-vr-bmc-nvidia.dts
arch/arm/dts/Makefile +1 -0
index fa6837be74..51e1729eeb 100755
@@ -702,6 +702,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	ast2600-slt.dtb \
 	ast2600-tacoma.dtb \
 	ast2600-tacoma.dtb \
+	ast2600-vr-bmc-nvidia.dtb \
 	ast2600-x4tf.dtb \
 	ast2600a0-evb.dtb \
 	ast2600a1-evb.dtb
arch/arm/dts/ast2600-vr-bmc-nvidia.dts new file +155 -0

155 lines not on this page · raw message

Signature · 1 line
2.43.0
#1 lore raw
Quoted 10 lines · Jacky Huang

Adds a dts for the NVIDIA VR-NVL BMC board, an AST2600-based BMC for the Vera Rubin NVL platform.

MAC0 uses phy-mode = "rgmii-id" with no SoC-side clk-delay node, so it relies on the zero default introduced by commit 3f6198c0db1c ("clk:
ast2600: set default clk-delay for all ethernet macs to 0"). With that change in place, MAC0 brings up its MDIO bus and establishes a link with the on-board PHY.

[...]

Applied to openbmc/u-boot.git (v2019.04-aspeed-openbmc), thanks!

Please note: Your change will not be available in OpenBMC until the commit reference of u-boot got bumped. This will likely happen within the next hours.

[1/1] ARM: dts: aspeed: Add Nvidia VR-NVL BMC

      https://github.com/openbmc/u-boot/commit/edc4a61d116f

Cheers,
Tan