Skip to contentSkip to conversation

ARM: dts: r8a7790-lager: Add VDD MPU regulator for DVFS

RFC In review Benoit Cousson 2 participants 2 messages Feb 26, 2014 – Feb 27, 2014

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

RFC 1/4 ARM: dts: r8a7790-lager: Add VDD MPU regulator for DVFS

The CA15 cluster is capable of voltage scaling. Add the regulator in the i2c3 node, to allow the generic CPUFreq driver to use it.

Enable the i2c3 pin mux and the device node as well since the da9210 is connected to that bus.

Note: Vmin is set to 0.8v to allow experimentation only. There is no guaranty that the CPUs will still work at this voltage.

---
 arch/arm/boot/dts/r8a7790-lager.dts | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)
arch/arm/boot/dts/r8a7790-lager.dts +21 -0
index 6e99eb2..5f77e3a 100644
@@ -159,6 +159,11 @@
 		renesas,groups = "qspi_ctrl", "qspi_data4";
 		renesas,function = "qspi";
 	};
+
+	i2c3_pins: i2c3 {
+		renesas,groups = "i2c3";
+		renesas,function = "i2c3";
+	};
 };
 
 &ether {
@@ -240,3 +245,19 @@
 	cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+	status = "okay";
+
+	vdd_dvfs: regulator@68 {
+		compatible = "diasemi,da9210";
+		reg = <0x68>;
+
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};
Signature · 1 line
1.8.3.2
#1 lore raw
Quoted 20 lines · Benoit Cousson

The CA15 cluster is capable of voltage scaling. Add the regulator in the i2c3 node, to allow the generic CPUFreq driver to use it.

Enable the i2c3 pin mux and the device node as well since the da9210 is connected to that bus.

Note: Vmin is set to 0.8v to allow experimentation only. There is no guaranty that the CPUs will still work at this voltage.

---
  arch/arm/boot/dts/r8a7790-lager.dts | 21 +++++++++++++++++++++
  1 file changed, 21 insertions(+)
arch/arm/boot/dts/r8a7790-lager.dts +0 -0
index 6e99eb2..5f77e3a 100644

arch/arm/boot/dts/r8a7790-lager.dts line 167

Quoted 9 lines
arch/arm/boot/dts/r8a7790-lager.dts +5 -0
@@ -159,6 +159,11 @@
  		renesas,groups = "qspi_ctrl", "qspi_data4";
  		renesas,function = "qspi";
  	};
+
+	i2c3_pins: i2c3 {
+		renesas,groups = "i2c3";
+		renesas,function = "i2c3";
+	};
  };

I thought i2c3 was a single function set of pins?

Signature · 2 lines
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius