Skip to contentSkip to conversation

Can I load uEnv.txt conditionally, based on the boot source?

U-Boot Brian Smucker 2 participants 4 messages Feb 11, 2015

lore
Share & tools
lore
#0 lore raw

Hello,

I was wondering if there is a way to tell what the boot source is?

My am335x SOC can boot to the mmc or the flash, based on the status of a digital line. I would like to load the uEnv.txt, only if booting from SD card (mmc). I notice at least in some codebases that the automatic loading of uEnv.txt is based on whether the SD card is available, not whether we are currently booting from the SD card.

Is there a way to sense which we are booting from?

Thanks

Brian

#1 lore raw
Quoted 6 lines · Brian Smucker

Hello,

I was wondering if there is a way to tell what the boot source is?

My am335x SOC can boot to the mmc or the flash, based on the status of a

digital line. I would like to load the uEnv.txt, only if booting from SD card (mmc). I notice at least in some codebases that the automatic loading of uEnv.txt is based on whether the SD card is available, not whether we are currently booting from the SD card.

Quoted 2 lines

Is there a way to sense which we are booting from?

Are you able to read the same digital line that the SoC is using to decide?

#2 lore raw

Hello,

That would be the most obvious thing, wouldn't it. I thought of that, but am not sure of the answer in u-boot.

Thanks,
Brian

Quoted 18 lines · Joe Hershberger
Quoted 6 lines · On Tue, Feb 10, 2015 at 7:18 PM, Brian Smucker <[email protected]…

Hello,

I was wondering if there is a way to tell what the boot source is?

My am335x SOC can boot to the mmc or the flash, based on the status

of a digital line. I would like to load the uEnv.txt, only if booting from SD card (mmc). I notice at least in some codebases that the automatic loading of uEnv.txt is based on whether the SD card is available, not whether we are currently booting from the SD card.

Quoted 2 lines

Is there a way to sense which we are booting from?

Are you able to read the same digital line that the SoC is using to decide?

#3 lore raw

Hi Brian,

Quoted 4 lines · Brian Smucker

Hello,

That would be the most obvious thing, wouldn't it. I thought of that,

but am not sure of the answer in u-boot.

Remember not to top post to the list.

Many devices have a GPIO driver available. Sometimes it's not enabled by the default config. As long as the pin is a GPIO as well as a boot-mode selector it should be easiest to just read the state of the line and load the file or not based on that in a shell script.

Cheers,
-Joe

Quoted 8 lines

Thanks,
Brian

On 2/11/2015 12:09 AM, Joe Hershberger wrote:

On Tue, Feb 10, 2015 at 7:18 PM, Brian Smucker <[email protected]>

Quoted 6 lines · wrote:
Quoted 6 lines

Hello,

I was wondering if there is a way to tell what the boot source is?

My am335x SOC can boot to the mmc or the flash, based on the status of

a digital line. I would like to load the uEnv.txt, only if booting from SD card (mmc). I notice at least in some codebases that the automatic loading of uEnv.txt is based on whether the SD card is available, not whether we are currently booting from the SD card.

Quoted 4 lines
Quoted 2 lines

Is there a way to sense which we are booting from?

Are you able to read the same digital line that the SoC is using to

decide?

Quoted 2 lines