Skip to contentSkip to conversation

DTS updates for Marvell Armada CN913x platforms

PATCH In review [email protected] 3 participants 8 messages Jul 8, 2021 – Jul 23, 2021

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

v7 cover DTS updates for Marvell Armada CN913x platforms

From: Konstantin Porotchkin <[email protected]>

This patch series contains the following changes/fixes:
1. Add support for Armada CN913x Development Board topology "B"
2. Add support for Armada CN913x Reference Design boards (CRB)
3. Fixes the NAND paritioninig scheme in DTS eliminating gap between consecutive partitions
4. Fix 10Gb ports PHY mode names

v2:
- extract common nodes from DB boards to separate DTSI files
- disable eth2 on CRB boards until the required phy mode support is added
- mention the switch part ID in CRB board description

v3:
- do not rename setup A DTS files for DB variants
- fix a couple of wrong include names

v4:
- Rebase on top of Linus master branch (v5.11-rc7)
- Remove HS400 timing from CRB AP SDHCI (not supported by connected eMMC)
- Add cd-gpio entry to CP0 SDHCI for SD card support
- Add a comment to CN9130-CRB patch about the required defconfig changes for supporting the onboard i2c expander
- Add Stefan's patch to enable 10G port on CN9130-DB platforms

v5:
- Extend enablement of 10G port to CN9131-DB platform

v6:
- Rebased on top of 5.13-rc, merging UTMI settings (requested by Gregory Clement)

v7:
- Remove documentation patch fixing CP11X references in PHY binding document
- Change Armada's family 10Gb port phy mode names from 10gbase-kr to 10gbase-r

Konstantin Porotchkin (4):
arch/arm64/boot/dts/marvell: fix NAND partitioning scheme
arm64: dts: cn913x: add device trees for topology B boards
arm64: dts: add support for Marvell cn9130-crb platform arch/arm64: dts: change 10gbase-kr to 10gbase-r in Armada

Stefan Chulski (1):
dts: marvell: Enable 10G interfaces on 9130-DB and 9131-DB boards

 arch/arm64/boot/dts/marvell/Makefile          |   5 +
 .../arm64/boot/dts/marvell/armada-7040-db.dts |   2 +-
 .../arm64/boot/dts/marvell/armada-8040-db.dts |   4 +-
 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts  |  38 ++
 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts  |  46 ++
 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi   | 222 ++++++++++
 arch/arm64/boot/dts/marvell/cn9130-db-B.dts   |  22 +
 arch/arm64/boot/dts/marvell/cn9130-db.dts     | 403 +----------------
 arch/arm64/boot/dts/marvell/cn9130-db.dtsi    | 410 ++++++++++++++++++
 arch/arm64/boot/dts/marvell/cn9131-db-B.dts   |  22 +
 arch/arm64/boot/dts/marvell/cn9131-db.dts     | 197 +--------
 arch/arm64/boot/dts/marvell/cn9131-db.dtsi    | 206 +++++++++
 arch/arm64/boot/dts/marvell/cn9132-db-B.dts   |  22 +
 arch/arm64/boot/dts/marvell/cn9132-db.dts     | 218 +---------
 arch/arm64/boot/dts/marvell/cn9132-db.dtsi    | 227 ++++++++++
 15 files changed, 1241 insertions(+), 803 deletions(-)
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi
 create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi
 create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsi
Signature · 1 line
2.17.1
#1 lore raw

PATCH v7 1/5 arch/arm64/boot/dts/marvell: fix NAND partitioning scheme

From: Konstantin Porotchkin <[email protected]>

Eliminate 1MB gap between Linux and filesystem partitions.

---
 arch/arm64/boot/dts/marvell/cn9130-db.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/boot/dts/marvell/cn9130-db.dts +1 -1
index 2c2af001619b..9758609541c7 100644
@@ -260,7 +260,7 @@
 			};
 			partition@200000 {
 				label = "Linux";
-				reg = <0x200000 0xd00000>;
+				reg = <0x200000 0xe00000>;
 			};
 			partition@1000000 {
 				label = "Filesystem";
Signature · 1 line
2.17.1
#2 lore raw

PATCH v7 2/5 arm64: dts: cn913x: add device trees for topology B boards

In reply to [email protected]

From: Konstantin Porotchkin <[email protected]>

The CN913x DB with topology B is similar to a regular setup (A) boards, but uses NAND flash as a boot device, while topology A boards are booting from SPI flash.
Since NAND and SPI on CN913x DB boards share some wires, they cannot be activated simultaneously.
The DTS files for setup "B" are based on setup "A", in which the CP0 NAND controller enabled and CP0 SPI1 disabled.

---
 arch/arm64/boot/dts/marvell/Makefile        |   3 +
 arch/arm64/boot/dts/marvell/cn9130-db-B.dts |  22 ++
 arch/arm64/boot/dts/marvell/cn9130-db.dts   | 403 +------------------
 arch/arm64/boot/dts/marvell/cn9130-db.dtsi  | 410 ++++++++++++++++++++
 arch/arm64/boot/dts/marvell/cn9131-db-B.dts |  22 ++
 arch/arm64/boot/dts/marvell/cn9131-db.dts   | 197 +---------
 arch/arm64/boot/dts/marvell/cn9131-db.dtsi  | 206 ++++++++++
 arch/arm64/boot/dts/marvell/cn9132-db-B.dts |  22 ++
 arch/arm64/boot/dts/marvell/cn9132-db.dts   | 218 +----------
 arch/arm64/boot/dts/marvell/cn9132-db.dtsi  | 227 +++++++++++
 10 files changed, 930 insertions(+), 800 deletions(-)
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi
 create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi
 create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsi
arch/arm64/boot/dts/marvell/Makefile +3 -0
index 34efe0fb6f37..5e39f9774e68 100644
@@ -16,5 +16,8 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin-singleshot.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-puzzle-m801.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8080-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9130-db.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9130-db-B.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db-B.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db-B.dtb
arch/arm64/boot/dts/marvell/cn9130-db-B.dts new file +22 -0
new file mode 100644
index 000000000000..57e41cacd483
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2020 Marvell International Ltd.
+ *
+ * Device tree for the CN9130-DB board (setup "B").
+ */
+
+#include "cn9130-db.dtsi"
+
+/ {
+	model = "Marvell Armada CN9130-DB setup B";
+};
+
+/* Setup B has NAND flash as a boot device, while regular setup uses SPI flash.
+ * Since CP0 SPI1 and CP0 NAND are sharing some pins, they cannot be activated
+ * simultaneously. When NAND controller is enabled, SPI1 should be disabled.
+ */
+
+&cp0_nand_controller {
+	status = "okay";
+};
+
arch/arm64/boot/dts/marvell/cn9130-db.dts +6 -397

415 lines not on this page · raw message

arch/arm64/boot/dts/marvell/cn9130-db.dtsi new file +410 -0

410 lines not on this page · raw message

arch/arm64/boot/dts/marvell/cn9131-db-B.dts new file +22 -0
new file mode 100644
index 000000000000..183b1ec8b1f0
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2020 Marvell International Ltd.
+ *
+ * Device tree for the CN9131-DB board (setup "B").
+ */
+
+#include "cn9131-db.dtsi"
+
+/ {
+	model = "Marvell Armada CN9131-DB setup B";
+};
+
+/* Setup B has NAND flash as a boot device, while regular setup uses SPI flash.
+ * Since CP0 SPI1 and CP0 NAND are sharing some pins, they cannot be activated
+ * simultaneously. When NAND controller is enabled, SPI1 should be disabled.
+ */
+
+&cp0_nand_controller {
+	status = "okay";
+};
+
arch/arm64/boot/dts/marvell/cn9131-db.dts +6 -191

209 lines not on this page · raw message

arch/arm64/boot/dts/marvell/cn9131-db.dtsi new file +206 -0

206 lines not on this page · raw message

arch/arm64/boot/dts/marvell/cn9132-db-B.dts new file +22 -0
new file mode 100644
index 000000000000..7137a6f22d0f
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Marvell International Ltd.
+ *
+ * Device tree for the CN9132-DB board.
+ */
+
+#include "cn9132-db.dtsi"
+
+/ {
+	model = "Marvell Armada CN9132-DB setup B";
+};
+
+/* Setup B has NAND flash as a boot device, while regular setup uses SPI flash.
+ * Since CP0 SPI1 and CP0 NAND are sharing some pins, they cannot be activated
+ * simultaneously. When NAND controller is enabled, SPI1 should be disabled.
+ */
+
+&cp0_nand_controller {
+	status = "okay";
+};
+
arch/arm64/boot/dts/marvell/cn9132-db.dts +6 -212

230 lines not on this page · raw message

arch/arm64/boot/dts/marvell/cn9132-db.dtsi new file +227 -0

227 lines not on this page · raw message

Signature · 1 line
2.17.1
#3 lore raw

PATCH v7 3/5 dts: marvell: Enable 10G interfaces on 9130-DB and 9131-DB boards

In reply to [email protected]

From: Stefan Chulski <[email protected]>

This patch enables eth0 10G interface on CN9130-DB paltforms and eth0 10G and eth3 10G interfaces on CN9131-DB.

---
 arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 2 +-
 arch/arm64/boot/dts/marvell/cn9131-db.dtsi | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)
arch/arm64/boot/dts/marvell/cn9130-db.dtsi +1 -1
index 34274e061958..39fc90716454 100644
@@ -125,7 +125,7 @@
 
 /* SLM-1521-V2, CON9 */
 &cp0_eth0 {
-	status = "disabled";
+	status = "okay";
 	phy-mode = "10gbase-kr";
 	/* Generic PHY, providing serdes lanes */
 	phys = <&cp0_comphy4 0>;
arch/arm64/boot/dts/marvell/cn9131-db.dtsi +1 -1
index a7ab791631bc..daddab638fb8 100644
@@ -84,7 +84,7 @@
 
 /* CON50 */
 &cp1_eth0 {
-	status = "disabled";
+	status = "okay";
 	phy-mode = "10gbase-kr";
 	/* Generic PHY, providing serdes lanes */
 	phys = <&cp1_comphy4 0>;
Signature · 1 line
2.17.1
#4 lore raw

PATCH v7 4/5 arm64: dts: add support for Marvell cn9130-crb platform

In reply to [email protected]

From: Konstantin Porotchkin <[email protected]>

The Marvell reference platform CN9130-CRB is a small form factor board in a metal case. The platform is based on CN9130 SoC with addition of 8 Gigabit ports SOHO Ethernet switch.
The reference platform features the following:
* Up to 4 CPU cores ARMv8 Cortex-A72 CPU
* CPU core operating speed of up to 2.2GHz
* DDR4 DIMM – 8GB 64bit+ECC @ 2400Mhz.
* 1x eMMC 8GB device
* 1x uSD card 4 bits port on CP
* 1x 128MB SPI NOR flash memory
* 1x USB 3.0 Host port (Type A)
* 1x SATA Gen3 via M.2
* 1x USB 3.0 via M.2
* 1x SIM card slot
* 1x 1G Ethernet port via RGMII
* 1x 10G switch port over SFP+ connector
* 8x 1G ports through 88E6393X switch via XFI
* 1x 2.5G/1G/100M/10M port via HS_SGMII
* 1x PCI Express (PCIe)x1 Gen 3.0
* 1x PCI Express (PCIe)x4 Gen 3.0 via NVMe M.2
* JTAG port

The CRB board uses MCP23017 i2c pin controller that drives the onboard eMMC abd USB 3,0 port power lines.
The following configuration should be enabled for this controller support:
CONFIG_PINCTRL_MCP23S08=y

The plaform supports two HW configurations - "A" and "B" CN9130-CRB-A
* AP-MPP configuration: SDIO, UART
* CP0 Serdes configuration:
* Lane0-3: NVMe (PCIe x4)
* Lane4: XFI
* Lane5: HS_SGMII

2. CN9130-CRB-B
* AP-MPP configuration: SDIO, UART
* CP0-MPP configuration: RGMII, SDIO, I2C0, I2C1, SMI, XSMI
* CP0 Serdes configuration:
* Lane0: PCIe x1
* Lane1: USB3_0 x1
* Lane2: SATA x1
* Lane3: USB3_1 x1
* Lane4: XFI
* Lane5: HS_SGMII

---
 arch/arm64/boot/dts/marvell/Makefile         |   2 +
 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts |  38 ++++
 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts |  46 ++++
 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi  | 222 ++++++++++++++++++++
 4 files changed, 308 insertions(+)
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
arch/arm64/boot/dts/marvell/Makefile +2 -0
index 5e39f9774e68..c686a8dd3ca5 100644
@@ -21,3 +21,5 @@ dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db-B.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db-B.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-A.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-B.dtb
arch/arm64/boot/dts/marvell/cn9130-crb-A.dts new file +38 -0
new file mode 100644
index 000000000000..a7b6dfba8af5
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 Marvell International Ltd.
+ */
+
+#include "cn9130-crb.dtsi"
+
+/ {
+	model = "Marvell Armada CN9130-CRB-A";
+};
+
+&cp0_pcie0 {
+	status = "okay";
+	num-lanes = <4>;
+	num-viewport = <8>;
+	/* Generic PHY, providing serdes lanes */
+	phys = <&cp0_comphy0 0
+		&cp0_comphy1 0
+		&cp0_comphy2 0
+		&cp0_comphy3 0>;
+	iommu-map =
+		<0x0   &smmu 0x480 0x20>,
+		<0x100 &smmu 0x4a0 0x20>,
+		<0x200 &smmu 0x4c0 0x20>;
+	iommu-map-mask = <0x031f>;
+};
+
+&cp0_usb3_0 {
+	status = "okay";
+	usb-phy = <&cp0_usb3_0_phy0>;
+	phy-names = "usb";
+};
+
+&cp0_usb3_1 {
+	status = "okay";
+	usb-phy = <&cp0_usb3_0_phy1>;
+	phy-names = "usb";
+};
arch/arm64/boot/dts/marvell/cn9130-crb-B.dts new file +46 -0

46 lines not on this page · raw message

arch/arm64/boot/dts/marvell/cn9130-crb.dtsi new file +222 -0

222 lines not on this page · raw message

Signature · 1 line
2.17.1
#5 lore raw

PATCH v7 5/5 arch/arm64: dts: change 10gbase-kr to 10gbase-r in Armada

In reply to [email protected]

From: Konstantin Porotchkin <[email protected]>

Change all 10G port modes in Armada family device trees from 10gbase-kr to 10gbase-r

---
 arch/arm64/boot/dts/marvell/armada-7040-db.dts | 2 +-
 arch/arm64/boot/dts/marvell/armada-8040-db.dts | 4 ++--
 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi    | 2 +-
 arch/arm64/boot/dts/marvell/cn9130-db.dtsi     | 2 +-
 arch/arm64/boot/dts/marvell/cn9131-db.dtsi     | 2 +-
 arch/arm64/boot/dts/marvell/cn9132-db.dtsi     | 2 +-
 6 files changed, 7 insertions(+), 7 deletions(-)
arch/arm64/boot/dts/marvell/armada-7040-db.dts +1 -1
index 51f3e2907597..cd326fe224ce 100644
@@ -282,7 +282,7 @@
 &cp0_eth0 {
 	status = "okay";
 	/* Network PHY */
-	phy-mode = "10gbase-kr";
+	phy-mode = "10gbase-r";
 	/* Generic PHY, providing serdes lanes */
 	phys = <&cp0_comphy2 0>;
 
arch/arm64/boot/dts/marvell/armada-8040-db.dts +2 -2
index e39e1efc95b6..f2e8e0df8865 100644
@@ -195,7 +195,7 @@
 
 &cp0_eth0 {
 	status = "okay";
-	phy-mode = "10gbase-kr";
+	phy-mode = "10gbase-r";
 
 	fixed-link {
 		speed = <10000>;
@@ -348,7 +348,7 @@
 
 &cp1_eth0 {
 	status = "okay";
-	phy-mode = "10gbase-kr";
+	phy-mode = "10gbase-r";
 
 	fixed-link {
 		speed = <10000>;
arch/arm64/boot/dts/marvell/cn9130-crb.dtsi +1 -1
index 75933477324a..9f0efcdacdf1 100644
@@ -202,7 +202,7 @@
 &cp0_eth0 {
 	/* This port is connected to 88E6393X switch */
 	status = "okay";
-	phy-mode = "10gbase-kr";
+	phy-mode = "10gbase-r";
 	managed = "in-band-status";
 	phys = <&cp0_comphy4 0>;
 };
arch/arm64/boot/dts/marvell/cn9130-db.dtsi +1 -1
index 39fc90716454..2cd4bb09e8ff 100644
@@ -126,7 +126,7 @@
 /* SLM-1521-V2, CON9 */
 &cp0_eth0 {
 	status = "okay";
-	phy-mode = "10gbase-kr";
+	phy-mode = "10gbase-r";
 	/* Generic PHY, providing serdes lanes */
 	phys = <&cp0_comphy4 0>;
 	managed = "in-band-status";
arch/arm64/boot/dts/marvell/cn9131-db.dtsi +1 -1
index daddab638fb8..f995b1bcda01 100644
@@ -85,7 +85,7 @@
 /* CON50 */
 &cp1_eth0 {
 	status = "okay";
-	phy-mode = "10gbase-kr";
+	phy-mode = "10gbase-r";
 	/* Generic PHY, providing serdes lanes */
 	phys = <&cp1_comphy4 0>;
 	managed = "in-band-status";
arch/arm64/boot/dts/marvell/cn9132-db.dtsi +1 -1
index 5948de6b4638..3f1795fb4fe7 100644
@@ -103,7 +103,7 @@
 /* SLM-1521-V2, CON9 */
 &cp2_eth0 {
 	status = "disabled";
-	phy-mode = "10gbase-kr";
+	phy-mode = "10gbase-r";
 	/* Generic PHY, providing serdes lanes */
 	phys = <&cp2_comphy4 0>;
 	managed = "in-band-status";
Signature · 1 line
2.17.1
Reviewed-by on v7 5/5
#6 lore raw

Re: [PATCH v7 5/5] arch/arm64: dts: change 10gbase-kr to 10gbase-r in Armada

Quoted 7 lines · On Thu, Jul 08, 2021 at 03:46:12PM +0300, [email protected] wrote:

From: Konstantin Porotchkin <[email protected]>

Change all 10G port modes in Armada family device trees from 10gbase-kr to 10gbase-r

Please change the "suggested-by" to:

Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!
maintainer
#7 lore raw
In reply to [email protected]

Hi Kosta,

Quoted 37 lines

From: Konstantin Porotchkin <[email protected]>

This patch series contains the following changes/fixes:
1. Add support for Armada CN913x Development Board topology "B"
2. Add support for Armada CN913x Reference Design boards (CRB)
3. Fixes the NAND paritioninig scheme in DTS eliminating gap between consecutive partitions
4. Fix 10Gb ports PHY mode names

v2:
- extract common nodes from DB boards to separate DTSI files
- disable eth2 on CRB boards until the required phy mode support is added
- mention the switch part ID in CRB board description

v3:
- do not rename setup A DTS files for DB variants
- fix a couple of wrong include names

v4:
- Rebase on top of Linus master branch (v5.11-rc7)
- Remove HS400 timing from CRB AP SDHCI (not supported by connected eMMC)
- Add cd-gpio entry to CP0 SDHCI for SD card support
- Add a comment to CN9130-CRB patch about the required defconfig changes for supporting the onboard i2c expander
- Add Stefan's patch to enable 10G port on CN9130-DB platforms

v5:
- Extend enablement of 10G port to CN9131-DB platform

v6:
- Rebased on top of 5.13-rc, merging UTMI settings (requested by Gregory Clement)

v7:
- Remove documentation patch fixing CP11X references in PHY binding document
- Change Armada's family 10Gb port phy mode names from 10gbase-kr to 10gbase-r

Quoted 9 lines

Konstantin Porotchkin (4):
arch/arm64/boot/dts/marvell: fix NAND partitioning scheme
arm64: dts: cn913x: add device trees for topology B boards
arm64: dts: add support for Marvell cn9130-crb platform arch/arm64: dts: change 10gbase-kr to 10gbase-r in Armada

Stefan Chulski (1):
dts: marvell: Enable 10G interfaces on 9130-DB and 9131-DB boards

Series applied on mvebu/dt64

Thanks,

Gregory

Quoted 29 lines
 arch/arm64/boot/dts/marvell/Makefile          |   5 +
 .../arm64/boot/dts/marvell/armada-7040-db.dts |   2 +-
 .../arm64/boot/dts/marvell/armada-8040-db.dts |   4 +-
 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts  |  38 ++
 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts  |  46 ++
 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi   | 222 ++++++++++
 arch/arm64/boot/dts/marvell/cn9130-db-B.dts   |  22 +
 arch/arm64/boot/dts/marvell/cn9130-db.dts     | 403 +----------------
 arch/arm64/boot/dts/marvell/cn9130-db.dtsi    | 410 ++++++++++++++++++
 arch/arm64/boot/dts/marvell/cn9131-db-B.dts   |  22 +
 arch/arm64/boot/dts/marvell/cn9131-db.dts     | 197 +--------
 arch/arm64/boot/dts/marvell/cn9131-db.dtsi    | 206 +++++++++
 arch/arm64/boot/dts/marvell/cn9132-db-B.dts   |  22 +
 arch/arm64/boot/dts/marvell/cn9132-db.dts     | 218 +---------
 arch/arm64/boot/dts/marvell/cn9132-db.dtsi    | 227 ++++++++++
 15 files changed, 1241 insertions(+), 803 deletions(-)
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi
 create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi
 create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsi
Signature · 1 line
2.17.1
Signature · 3 lines
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
http://bootlin.com