ASoC: tas2552: Describe the possible I2C addresses
Subsystems (2)
PATCH 1/2 ASoC: tas2552: Describe the possible I2C addresses
According to the TAS2552 datasheet the possible I2C addresses are:
0x40 - when ADDR pin is 00x41 - when ADDR pin is 1
List the possible values for better clarification.
--- Documentation/devicetree/bindings/sound/tas2552.txt | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/sound/tas2552.txt +2 -1
@@ -5,7 +5,8 @@ The tas2552 serial control bus communicates through I2C protocols Required properties: - compatible - One of: "ti,tas2552" - TAS2552 - - reg - I2C slave address + - reg - I2C slave address: it can be 0x40 if ADDR pin is 0 + or 0x41 if ADDR pin is 1. - supply-*: Required supply regulators are: "vbat" battery voltage "iovdd" I/O Voltage
Signature · 1 line
2.7.4
PATCH 2/2 ASoC: tas2552: Fix typos in the binding doc
Fix the following typos:
"receive its reference clock" and "selected".
--- Documentation/devicetree/bindings/sound/tas2552.txt | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
Documentation/devicetree/bindings/sound/tas2552.txt +2 -2
@@ -15,11 +15,11 @@ Required properties: Optional properties: - enable-gpio - gpio pin to enable/disable the device -tas2552 can receive it's reference clock via MCLK, BCLK, IVCLKIN pin or use the +tas2552 can receive its reference clock via MCLK, BCLK, IVCLKIN pin or use the internal 1.8MHz. This CLKIN is used by the PLL. In addition to PLL, the PDM reference clock is also selectable: PLL, IVCLKIN, BCLK or MCLK. For system integration the dt-bindings/sound/tas2552.h header file provides -defined values to selct and configure the PLL and PDM reference clocks. +defined values to select and configure the PLL and PDM reference clocks. Example:
Signature · 1 line
2.7.4
Mark Brown
maintainerApplied "ASoC: tas2552: Fix typos in the binding doc" to the asoc tree
The patch
ASoC: tas2552: Fix typos in the binding doc
has been applied to the asoc tree at
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks,
Mark
Quoted 1 line
From
7d8d2c9482474804a5c2b33ea9218d33dbcb48baMon Sep 17 00:00:00 2001
From: Fabio Estevam <[email protected]>
Date: Tue, 11 Apr 2017 15:49:35 -0300
Subject: [PATCH] ASoC: tas2552: Fix typos in the binding doc
Fix the following typos:
"receive its reference clock" and "selected".
--- Documentation/devicetree/bindings/sound/tas2552.txt | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
Documentation/devicetree/bindings/sound/tas2552.txt +2 -2
@@ -15,11 +15,11 @@ Required properties: Optional properties: - enable-gpio - gpio pin to enable/disable the device -tas2552 can receive it's reference clock via MCLK, BCLK, IVCLKIN pin or use the +tas2552 can receive its reference clock via MCLK, BCLK, IVCLKIN pin or use the internal 1.8MHz. This CLKIN is used by the PLL. In addition to PLL, the PDM reference clock is also selectable: PLL, IVCLKIN, BCLK or MCLK. For system integration the dt-bindings/sound/tas2552.h header file provides -defined values to selct and configure the PLL and PDM reference clocks. +defined values to select and configure the PLL and PDM reference clocks. Example:
Signature · 1 line
2.11.0
Mark Brown
maintainerApplied "ASoC: tas2552: Describe the possible I2C addresses" to the asoc tree
In reply to Fabio EstevamThe patch
ASoC: tas2552: Describe the possible I2C addresses
has been applied to the asoc tree at
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks,
Mark
Quoted 1 line
From
ddea87ea79927ba0b94e697a505f90fe06c29f84Mon Sep 17 00:00:00 2001
From: Fabio Estevam <[email protected]>
Date: Tue, 11 Apr 2017 15:49:34 -0300
Subject: [PATCH] ASoC: tas2552: Describe the possible I2C addresses
According to the TAS2552 datasheet the possible I2C addresses are:
0x40 - when ADDR pin is 00x41 - when ADDR pin is 1
List the possible values for better clarification.
--- Documentation/devicetree/bindings/sound/tas2552.txt | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/sound/tas2552.txt +2 -1
@@ -5,7 +5,8 @@ The tas2552 serial control bus communicates through I2C protocols Required properties: - compatible - One of: "ti,tas2552" - TAS2552 - - reg - I2C slave address + - reg - I2C slave address: it can be 0x40 if ADDR pin is 0 + or 0x41 if ADDR pin is 1. - supply-*: Required supply regulators are: "vbat" battery voltage "iovdd" I/O Voltage
Signature · 1 line
2.11.0