Add visibility for native NVMe multipath using sysfs
v7 cover Add visibility for native NVMe multipath using sysfs
Hi,
This RFC propose adding new sysfs attributes for adding visibility of nvme native multipath I/O.
The changes are divided into three patches.
The first patch adds visibility for round-robin io-policy. The second patch adds visibility for numa io-policy. The third patch adds the visibility for queue-depth io-policy.
As we know, NVMe native multipath supports three different io policies (numa, round-robin and queue-depth) for selecting I/O path, however, we don't have any visibility about which path is being selected by multipath code for forwarding I/O. This RFC helps add that visibility by adding new sysfs attribute files named "numa_nodes" and "queue_depth" under each namespace block device path /sys/block/nvmeXcYnZ/. We also create a "multipath" sysfs directory under head disk node and then from this directory add a link to each namespace path device this head disk node points to.
Please find below output generated with this proposed RFC patch applied on a system with two multi-controller PCIe NVMe disks attached to it. This system is also an NVMf-TCP host which is connected to an NVMf-TCP target over two NIC cards. This system has four numa nodes online when the below output was captured:
# cat /sys/devices/system/node/online 0-3
# lscpu <snip> NUMA: NUMA node(s): 4 NUMA node0 CPU(s): NUMA node1 CPU(s): 0-7 NUMA node2 CPU(s): 8-31 NUMA node3 CPU(s): 32-63 <snip>
Please note that numa node 0 though online, doesn't have any CPU currently assigned to it.
# nvme list -v Subsystem Subsystem-NQN Controllers ---------------- ------------------------------------------------------------------------------------------------ ---------------- nvme-subsys1 nqn.1994-11.com.samsung:nvme:PM1735a:2.5-inch:S6RTNE0R900057 nvme0, nvme1 nvme-subsys3 nqn.2019-10.com.kioxia:KCM7DRUG1T92:3D60A04906N1 nvme2, nvme3 nvme-subsys4 nvmet_subsystem nvme4, nvme5
Device Cntlid SN MN FR TxPort Address Slot Subsystem Namespaces
---------------- ------ -------------------- ---------------------------------------- -------- ------ -------------- ------ ------------ ----------------
nvme0 66 S6RTNE0R900057 3.2TB NVMe Gen4 U.2 SSD III REV.SN66 pcie 052e:78:00.0 U50EE.001.WZS000E-P3-C14-R1 nvme-subsys1 nvme1n1 nvme1 65 S6RTNE0R900057 3.2TB NVMe Gen4 U.2 SSD III REV.SN66 pcie 058e:78:00.0 U50EE.001.WZS000E-P3-C14-R2 nvme-subsys1 nvme1n1 nvme2 2 3D60A04906N1 1.6TB NVMe Gen4 U.2 SSD IV REV.CAS2 pcie 0524:28:00.0 U50EE.001.WZS000E-P3-C4-R1 nvme-subsys3 nvme3n1 nvme3 1 3D60A04906N1 1.6TB NVMe Gen4 U.2 SSD IV REV.CAS2 pcie 0584:28:00.0 U50EE.001.WZS000E-P3-C4-R2 nvme-subsys3 nvme3n1 nvme4 1 a224673364d1dcb6fab9 Linux 6.9.0-rc tcp traddr=20.0.0.200,trsvcid=4420,src_addr=20.0.0.100 nvme-subsys4 nvme4n1 nvme5 2 a224673364d1dcb6fab9 Linux 6.9.0-rc tcp traddr=10.0.0.200,trsvcid=4420,src_addr=10.0.0.100 nvme-subsys4 nvme4n1
Device Generic NSID Usage Format Controllers
----------------- ----------------- ---------- -------------------------- ---------------- ----------------
/dev/nvme1n1 /dev/ng1n1 0x1 5.75 GB / 5.75 GB 4 KiB + 0 B nvme0, nvme1 /dev/nvme3n1 /dev/ng3n1 0x2 0.00 B / 5.75 GB 4 KiB + 0 B nvme2, nvme3 /dev/nvme4n1 /dev/ng4n1 0x1 5.75 GB / 5.75 GB 4 KiB + 0 B nvme4, nvme5
# nvme show-topology
nvme-subsys1 - NQN=nqn.1994-11.com.samsung:nvme:PM1735a:2.5-inch:S6RTNE0R900057
hostnqn=nqn.2014-08.org.nvmexpress:uuid:41528538-e8ad-4eaf-84a7-9c552917d988
iopolicy=numa
\
+- ns 1
\
+- nvme0 pcie 052e:78:00.0 live optimized
+- nvme1 pcie 058e:78:00.0 live optimizednvme-subsys3 - NQN=nqn.2019-10.com.kioxia:KCM7DRUG1T92:3D60A04906N1
hostnqn=nqn.2014-08.org.nvmexpress:uuid:41528538-e8ad-4eaf-84a7-9c552917d988
iopolicy=round-robin
\
+- ns 2
\
+- nvme2 pcie 0524:28:00.0 live optimized
+- nvme3 pcie 0584:28:00.0 live optimizednvme-subsys4 - NQN=nvmet_subsystem
hostnqn=nqn.2014-08.org.nvmexpress:uuid:41528538-e8ad-4eaf-84a7-9c552917d988
iopolicy=queue-depth
\
+- ns 1
\
+- nvme4 tcp traddr=20.0.0.200,trsvcid=4420,src_addr=20.0.0.100 live optimized
+- nvme5 tcp traddr=10.0.0.200,trsvcid=4420,src_addr=10.0.0.100 live optimizedAs we could see above, we've three shared namespaces created. In terms of iopolicy, we have "numa" configured for nvme-subsys1, "round-robin" configured for nvme-subsys3 and "queue-depth" configured for nvme-subsys4.
Now, under each namespace "head disk node", we create a sysfs group attribute named "multipath". The "multipath" group then points to the each path this head disk node points to:
# tree /sys/block/nvme1n1/multipath/ /sys/block/nvme1n1/multipath/ ├── nvme1c0n1 -> ../../../../../pci052e:78/052e:78:00.0/nvme/nvme0/nvme1c0n1 └── nvme1c1n1 -> ../../../../../pci058e:78/058e:78:00.0/nvme/nvme1/nvme1c1n1
# tree /sys/block/nvme3n1/multipath/ /sys/block/nvme3n1/multipath/ ├── nvme3c2n1 -> ../../../../../pci0524:28/0524:28:00.0/nvme/nvme2/nvme3c2n1 └── nvme3c3n1 -> ../../../../../pci0584:28/0584:28:00.0/nvme/nvme3/nvme3c3n1
# tree /sys/block/nvme4n1/multipath/ /sys/block/nvme4n1/multipath/ ├── nvme4c4n1 -> ../../../../nvme-fabrics/ctl/nvme4/nvme4c4n1 └── nvme4c5n1 -> ../../../../nvme-fabrics/ctl/nvme5/nvme4c5n1
One can easily infer from the above output that for the "round-robin" I/O policy, configured under nvme-subsys3, the I/O workload targeted at nvme3n1 would toggle across nvme3c2n1 and nvme3c3n1 assuming the ana state of each path is optimized (as can be seen in the output of show-topology).
For numa I/O policy, configured under nvme-subsys1, the "numa_nodes" attribute file shows the numa nodes being preferred by the respective namespace path. The numa nodes value is comma delimited list of nodes or A-B range of nodes.
# cat /sys/block/nvme1n1/multipath/nvme1c0n1/numa_nodes 0-1
# cat /sys/block/nvme1n1/multipath/nvme1c1n1/numa_nodes 2-3
From the above output, one can easily infer that I/O workload targeted at nvme1n1 and running on numa nodes 0 and 1 would use path nvme1c0n1. Similarly, I/O workload running on numa nodes 2 and 3 would use path nvme1c1n1.
For queue-depth I/O policy, configured under nvme-subsys4, the "queue_depth" attribute file shows the number of active/in-flight I/O requests currently queued for each path.
# cat /sys/block/nvme4n1/multipath/nvme4c4n1/queue_depth 518
# cat /sys/block/nvme4n1/multipath/nvme4c5n1/queue_depth 504
From the above output, one can easily infer that I/O workload targeted at nvme4n1 uses two paths nvme4c4n1 and nvme4c5n1 and the current queue depth of each path is 518 and 504 respectively.
Changes since v6:
- Fix sysfs link warning menifested while running blktest nvme/058 (Keith Busch, Chaitanya Kulkarni)
- Link to v6: https://lore.kernel.org/all/[email protected]/
Changes since v5:
- Fix typo in the subject line of the first patch in the series (Danied Wagner)
- Link to v5: https://lore.kernel.org/all/[email protected]/
changes since v4:
- Ensure that we create sysfs link from head gendisk node to each path device irrespective of the ANA state of the path (Hannes Reinecke)
- Split the patch into three patch series and add commentary in the
code so that it's easy to read and understand the core logic (Sagi Grimberg)
- Don't show any output if user reads "numa_nodes" file and configured iopolicy is anything but numa; similarly don't emit any output if user reads "queue_depth" file and configured iopolicy is anything but queue-depth (Sagi Grimberg)
- Link to v4: https://lore.kernel.org/all/[email protected]/
Changes since v3:
- Protect the namespace dereference code with srcu read lock (Daniel Wagner)
- Link to v3: https://lore.kernel.org/all/[email protected]/
Changes since v2:
- Use one value per one sysfs attribute (Keith Busch)
- Link to v2: https://lore.kernel.org/all/[email protected]/
Changes since v1:
- Use sysfs to export multipath I/O information instead of debugfs
- Link to v1: https://lore.kernel.org/all/[email protected]/
Nilay Shroff (3):
nvme-multipath: Add visibility for round-robin io-policy
nvme-multipath: Add visibility for numa io-policy
nvme-multipath: Add visibility for queue-depth io-policy
drivers/nvme/host/core.c | 3 + drivers/nvme/host/multipath.c | 138 ++++++++++++++++++++++++++++++++++ drivers/nvme/host/nvme.h | 20 ++++- drivers/nvme/host/sysfs.c | 20 +++++ 4 files changed, 177 insertions(+), 4 deletions(-)
Signature · 1 line
2.47.1
RFC PATCH v7 1/3 nvme-multipath: Add visibility for round-robin io-policy
This patch helps add nvme native multipath visibility for round-robin io-policy. It creates a "multipath" sysfs directory under head gendisk device node directory and then from "multipath" directory it adds a link to each namespace path device the head node refers.
For instance, if we have a shared namespace accessible from two different controllers/paths then we create a soft link to each path device from head disk node as shown below:
$ ls -l /sys/block/nvme1n1/multipath/ nvme1c1n1 -> ../../../../../pci052e:78/052e:78:00.0/nvme/nvme1/nvme1c1n1 nvme1c3n1 -> ../../../../../pci058e:78/058e:78:00.0/nvme/nvme3/nvme1c3n1
In the above example, nvme1n1 is head gendisk node created for a shared namespace and the namespace is accessible from nvme1c1n1 and nvme1c3n1 paths.
For round-robin I/O policy, we could easily infer from the above output that I/O workload targeted to nvme1n1 would toggle across paths nvme1c1n1 and nvme1c3n1.
--- drivers/nvme/host/core.c | 3 ++ drivers/nvme/host/multipath.c | 99 +++++++++++++++++++++++++++++++++++ drivers/nvme/host/nvme.h | 18 +++++-- drivers/nvme/host/sysfs.c | 14 +++++ 4 files changed, 130 insertions(+), 4 deletions(-)
drivers/nvme/host/core.c +3 -0
@@ -3982,6 +3982,9 @@ static void nvme_ns_remove(struct nvme_ns *ns)if (!nvme_ns_head_multipath (ns->head))nvme_cdev_del (&ns->cdev, &ns->cdev_device); + +nvme_mpath_remove_sysfs_link (ns); +del_gendisk (ns->disk);mutex_lock (&ns->ctrl->namespaces_lock);
drivers/nvme/host/multipath.c +99 -0
117 lines not on this page · raw message
drivers/nvme/host/nvme.h +14 -4
@@ -534,10 +534,11 @@ struct nvme_ns {struct nvme_ns_head *head;unsigned long flags; -#define NVME_NS_REMOVING 0 -#define NVME_NS_ANA_PENDING 2 -#define NVME_NS_FORCE_RO 3 -#define NVME_NS_READY 4 +#define NVME_NS_REMOVING 0 +#define NVME_NS_ANA_PENDING 2 +#define NVME_NS_FORCE_RO 3 +#define NVME_NS_READY 4 +#define NVME_NS_SYSFS_ATTR_LINK 5struct cdev cdev;struct device cdev_device;
@@ -933,6 +934,7 @@ int nvme_getgeo(struct block_device *bdev, struct hd_geometry *geo);int nvme_dev_uring_cmd (struct io_uring_cmd *ioucmd,unsigned int issue_flags);extern const struct attribute_group *nvme_ns_attr_groups[]; +extern const struct attribute_group nvme_ns_mpath_attr_group;extern const struct pr_ops nvme_pr_ops;extern const struct block_device_operations nvme_ns_head_ops;extern const struct attribute_group nvme_dev_attrs_group;
@@ -955,6 +957,8 @@ void nvme_mpath_default_iopolicy(struct nvme_subsystem *subsys);void nvme_failover_req (struct request *req);void nvme_kick_requeue_lists (struct nvme_ctrl *ctrl);int nvme_mpath_alloc_disk (struct nvme_ctrl *ctrl,struct nvme_ns_head *head); +void nvme_mpath_add_sysfs_link (struct nvme_ns_head *ns); +void nvme_mpath_remove_sysfs_link (struct nvme_ns *ns);void nvme_mpath_add_disk (struct nvme_ns *ns,__le32 anagrpid);void nvme_mpath_remove_disk (struct nvme_ns_head *head);int nvme_mpath_init_identify (struct nvme_ctrl *ctrl,struct nvme_id_ctrl *id);
@@ -1009,6 +1013,12 @@ static inline void nvme_mpath_add_disk(struct nvme_ns *ns, __le32 anagrpid)static inline void nvme_mpath_remove_disk (struct nvme_ns_head *head) { } +static inline void nvme_mpath_add_sysfs_link (struct nvme_ns *ns) +{ +} +static inline void nvme_mpath_remove_sysfs_link (struct nvme_ns *ns) +{ +}static inline bool nvme_mpath_clear_current_path (struct nvme_ns *ns) {return false;
drivers/nvme/host/sysfs.c +14 -0
@@ -299,8 +299,22 @@ static const struct attribute_group nvme_ns_attr_group = { .is_visible = nvme_ns_attrs_are_visible, }; +#ifdef CONFIG_NVME_MULTIPATH +static struct attribute *nvme_ns_mpath_attrs[] = { +NULL , +}; + +const struct attribute_group nvme_ns_mpath_attr_group = { + .name ="multipath" , + .attrs = nvme_ns_mpath_attrs, +}; +#endif +const struct attribute_group *nvme_ns_attr_groups[] = { &nvme_ns_attr_group, +#ifdef CONFIG_NVME_MULTIPATH + &nvme_ns_mpath_attr_group, +#endifNULL , };
Signature · 1 line
2.47.1
Re: [PATCHv7 RFC 1/3] nvme-multipath: Add visibility for round-robin io-policy
Quoted 21 lines · Nilay Shroff
This patch helps add nvme native multipath visibility for round-robin io-policy. It creates a "multipath" sysfs directory under head gendisk device node directory and then from "multipath" directory it adds a link to each namespace path device the head node refers.
For instance, if we have a shared namespace accessible from two different controllers/paths then we create a soft link to each path device from head disk node as shown below:
$ ls -l /sys/block/nvme1n1/multipath/ nvme1c1n1 -> ../../../../../pci052e:78/052e:78:00.0/nvme/nvme1/nvme1c1n1 nvme1c3n1 -> ../../../../../pci058e:78/058e:78:00.0/nvme/nvme3/nvme1c3n1In the above example, nvme1n1 is head gendisk node created for a shared namespace and the namespace is accessible from nvme1c1n1 and nvme1c3n1 paths.
For round-robin I/O policy, we could easily infer from the above output that I/O workload targeted to nvme1n1 would toggle across paths nvme1c1n1 and nvme1c3n1.
Quoted 8 lines
Signed-off-by Nilay Shroff <[email protected]>--- drivers/nvme/host/core.c | 3 ++ drivers/nvme/host/multipath.c | 99 +++++++++++++++++++++++++++++++++++ drivers/nvme/host/nvme.h | 18 +++++-- drivers/nvme/host/sysfs.c | 14 +++++ 4 files changed, 130 insertions(+), 4 deletions(-)
Cheers,
Hannes
Signature · 4 lines
Dr. Hannes Reinecke Kernel Storage Architect [email protected] +49 911 74053 688 SUSE Software Solutions GmbH, Frankenstr. 146, 90461 Nürnberg HRB 36809 (AG Nürnberg), GF: I. Totev, A. McDonald, W. Knoblich
RFC PATCH v7 2/3 nvme-multipath: Add visibility for numa io-policy
In reply to Nilay ShroffThis patch helps add nvme native multipath visibility for numa io-policy. It adds a new attribute file named "numa_nodes" under namespace gendisk device path node which prints the list of numa nodes preferred by the given namespace path. The numa nodes value is comma delimited list of nodes or A-B range of nodes.
For instance, if we have a shared namespace accessible from two different controllers/paths then accessing head node of the shared namespace would show the following output:
$ ls -l /sys/block/nvme1n1/multipath/ nvme1c1n1 -> ../../../../../pci052e:78/052e:78:00.0/nvme/nvme1/nvme1c1n1 nvme1c3n1 -> ../../../../../pci058e:78/058e:78:00.0/nvme/nvme3/nvme1c3n1
In the above example, nvme1n1 is head gendisk node created for a shared namespace and this namespace is accessible from nvme1c1n1 and nvme1c3n1 paths. For numa io-policy we can then refer the "numa_nodes" attribute file created under each namespace path:
$ cat /sys/block/nvme1n1/multipath/nvme1c1n1/numa_nodes 0-1
$ cat /sys/block/nvme1n1/multipath/nvme1c3n1/numa_nodes 2-3
Quoted 1 line
From the above output, we infer that I/O workload targeted at nvme1n1
and running on numa nodes 0 and 1 would prefer using path nvme1c1n1. Similarly, I/O workload running on numa nodes 2 and 3 would prefer using path nvme1c3n1. Reading "numa_nodes" file when configured io-policy is anything but numa would show no output.
--- drivers/nvme/host/multipath.c | 27 +++++++++++++++++++++++++++ drivers/nvme/host/nvme.h | 1 + drivers/nvme/host/sysfs.c | 5 +++++ 3 files changed, 33 insertions(+)
drivers/nvme/host/multipath.c +27 -0
@@ -976,6 +976,33 @@ static ssize_t ana_state_show(struct device *dev, struct device_attribute *attr, }DEVICE_ATTR_RO (ana_state); +static ssize_t numa_nodes_show (struct device *dev,struct device_attribute *attr, +char *buf) +{ +int node, srcu_idx; +nodemask_t numa_nodes; +struct nvme_ns *current_ns; +struct nvme_ns *ns =nvme_get_ns_from_dev (dev); +struct nvme_ns_head *head = ns->head; + +if (head->subsys->iopolicy !=NVME_IOPOLICY_NUMA ) +return 0 ; + +nodes_clear (numa_nodes); + + srcu_idx =srcu_read_lock (&head->srcu); +for_each_node (node) { + current_ns =srcu_dereference (head->current_path[node], + &head->srcu); +if (ns == current_ns) +node_set (node, numa_nodes); + } +srcu_read_unlock (&head->srcu, srcu_idx); + +return sysfs_emit (buf,"%*pbl\n" ,nodemask_pr_args (&numa_nodes)); +} +DEVICE_ATTR_RO (numa_nodes); +static int nvme_lookup_ana_group_desc (struct nvme_ctrl *ctrl,struct nvme_ana_group_desc *desc,void *data) {
drivers/nvme/host/nvme.h +1 -0
@@ -984,6 +984,7 @@ static inline void nvme_trace_bio_complete(struct request *req)extern bool multipath;extern struct device_attribute dev_attr_ana_grpid;extern struct device_attribute dev_attr_ana_state; +extern struct device_attribute dev_attr_numa_nodes;extern struct device_attribute subsys_attr_iopolicy;static inline bool nvme_disk_is_ns_head (struct gendisk *disk)
drivers/nvme/host/sysfs.c +5 -0
@@ -258,6 +258,7 @@ static struct attribute *nvme_ns_attrs[] = {#ifdef CONFIG_NVME_MULTIPATH &dev_attr_ana_grpid.attr, &dev_attr_ana_state.attr, + &dev_attr_numa_nodes.attr, #endif &dev_attr_io_passthru_err_log_enabled.attr, NULL,
@@ -290,6 +291,10 @@ static umode_t nvme_ns_attrs_are_visible(struct kobject *kobj,if (!nvme_ctrl_use_ana (nvme_get_ns_from_dev (dev)->ctrl)) return 0; } +if (a == &dev_attr_numa_nodes.attr) { +if (nvme_disk_is_ns_head (dev_to_disk (dev))) +return 0 ; + }#endif return a->mode; }
Signature · 1 line
2.47.1
Re: [PATCHv7 RFC 2/3] nvme-multipath: Add visibility for numa io-policy
Quoted 31 lines · Nilay Shroff
This patch helps add nvme native multipath visibility for numa io-policy. It adds a new attribute file named "
numa_nodes" under namespace gendisk device path node which prints the list of numa nodes preferred by the given namespace path. The numa nodes value is comma delimited list of nodes or A-B range of nodes.For instance, if we have a shared namespace accessible from two different controllers/paths then accessing head node of the shared namespace would show the following output:
$ ls -l /sys/block/nvme1n1/multipath/ nvme1c1n1 -> ../../../../../pci052e:78/052e:78:00.0/nvme/nvme1/nvme1c1n1 nvme1c3n1 -> ../../../../../pci058e:78/058e:78:00.0/nvme/nvme3/nvme1c3n1In the above example, nvme1n1 is head gendisk node created for a shared namespace and this namespace is accessible from nvme1c1n1 and nvme1c3n1 paths. For numa io-policy we can then refer the "
numa_nodes" attribute file created under each namespace path:$ cat /sys/block/nvme1n1/multipath/nvme1c1n1/numa_nodes 0-1$ cat /sys/block/nvme1n1/multipath/nvme1c3n1/numa_nodes 2-3Quoted 1 line
From the above output, we infer that I/O workload targeted at nvme1n1
and running on numa nodes 0 and 1 would prefer using path nvme1c1n1. Similarly, I/O workload running on numa nodes 2 and 3 would prefer using path nvme1c3n1. Reading "
numa_nodes" file when configured io-policy is anything but numa would show no output.
Quoted 8 lines
Reviewed-by Sagi Grimberg <[email protected]>Signed-off-by Nilay Shroff <[email protected]>--- drivers/nvme/host/multipath.c | 27 +++++++++++++++++++++++++++ drivers/nvme/host/nvme.h | 1 + drivers/nvme/host/sysfs.c | 5 +++++ 3 files changed, 33 insertions(+)
Cheers,
Hannes
Signature · 4 lines
Dr. Hannes Reinecke Kernel Storage Architect [email protected] +49 911 74053 688 SUSE Software Solutions GmbH, Frankenstr. 146, 90461 Nürnberg HRB 36809 (AG Nürnberg), GF: I. Totev, A. McDonald, W. Knoblich
RFC PATCH v7 3/3 nvme-multipath: Add visibility for queue-depth io-policy
In reply to Nilay ShroffThis patch helps add nvme native multipath visibility for queue-depth io-policy. It adds a new attribute file named "queue_depth" under namespace device path node which would print the number of active/ in-flight I/O requests currently queued for the given path.
For instance, if we have a shared namespace accessible from two different controllers/paths then accessing head block node of the shared namespace would show the following output:
$ ls -l /sys/block/nvme1n1/multipath/ nvme1c1n1 -> ../../../../../pci052e:78/052e:78:00.0/nvme/nvme1/nvme1c1n1 nvme1c3n1 -> ../../../../../pci058e:78/058e:78:00.0/nvme/nvme3/nvme1c3n1
In the above example, nvme1n1 is head gendisk node created for a shared namespace and the namespace is accessible from nvme1c1n1 and nvme1c3n1 paths. For queue-depth io-policy we can then refer the "queue_depth" attribute file created under each namespace path:
$ cat /sys/block/nvme1n1/multipath/nvme1c1n1/queue_depth 518
$cat /sys/block/nvme1n1/multipath/nvme1c3n1/queue_depth 504
Quoted 1 line
From the above output, we can infer that I/O workload targeted at nvme1n1
uses two paths nvme1c1n1 and nvme1c3n1 and the current queue depth of each path is 518 and 504 respectively. Reading "queue_depth" file when configured io-policy is anything but queue-depth would show no output.
--- drivers/nvme/host/multipath.c | 12 ++++++++++++ drivers/nvme/host/nvme.h | 1 + drivers/nvme/host/sysfs.c | 3 ++- 3 files changed, 15 insertions(+), 1 deletion(-)
drivers/nvme/host/multipath.c +12 -0
@@ -976,6 +976,18 @@ static ssize_t ana_state_show(struct device *dev, struct device_attribute *attr, }DEVICE_ATTR_RO (ana_state); +static ssize_t queue_depth_show (struct device *dev, +struct device_attribute *attr,char *buf) +{ +struct nvme_ns *ns =nvme_get_ns_from_dev (dev); + +if (ns->head->subsys->iopolicy !=NVME_IOPOLICY_QD ) +return 0 ; + +return sysfs_emit (buf,"%d\n" ,atomic_read (&ns->ctrl->nr_active)); +} +DEVICE_ATTR_RO (queue_depth); +static ssize_t numa_nodes_show (struct device *dev,struct device_attribute *attr,char *buf) {
drivers/nvme/host/nvme.h +1 -0
@@ -984,6 +984,7 @@ static inline void nvme_trace_bio_complete(struct request *req)extern bool multipath;extern struct device_attribute dev_attr_ana_grpid;extern struct device_attribute dev_attr_ana_state; +extern struct device_attribute dev_attr_queue_depth;extern struct device_attribute dev_attr_numa_nodes;extern struct device_attribute subsys_attr_iopolicy;
drivers/nvme/host/sysfs.c +2 -1
@@ -258,6 +258,7 @@ static struct attribute *nvme_ns_attrs[] = {#ifdef CONFIG_NVME_MULTIPATH &dev_attr_ana_grpid.attr, &dev_attr_ana_state.attr, + &dev_attr_queue_depth.attr, &dev_attr_numa_nodes.attr, #endif &dev_attr_io_passthru_err_log_enabled.attr,
@@ -291,7 +292,7 @@ static umode_t nvme_ns_attrs_are_visible(struct kobject *kobj,if (!nvme_ctrl_use_ana (nvme_get_ns_from_dev (dev)->ctrl))return 0 ; } -if (a == &dev_attr_numa_nodes.attr) { +if (a == &dev_attr_queue_depth.attr || a == &dev_attr_numa_nodes.attr) {if (nvme_disk_is_ns_head (dev_to_disk (dev)))return 0 ; }
Signature · 1 line
2.47.1
Re: [PATCHv7 RFC 3/3] nvme-multipath: Add visibility for queue-depth io-policy
Quoted 29 lines · Nilay Shroff
This patch helps add nvme native multipath visibility for queue-depth io-policy. It adds a new attribute file named "
queue_depth" under namespace device path node which would print the number of active/ in-flight I/O requests currently queued for the given path.For instance, if we have a shared namespace accessible from two different controllers/paths then accessing head block node of the shared namespace would show the following output:
$ ls -l /sys/block/nvme1n1/multipath/ nvme1c1n1 -> ../../../../../pci052e:78/052e:78:00.0/nvme/nvme1/nvme1c1n1 nvme1c3n1 -> ../../../../../pci058e:78/058e:78:00.0/nvme/nvme3/nvme1c3n1In the above example, nvme1n1 is head gendisk node created for a shared namespace and the namespace is accessible from nvme1c1n1 and nvme1c3n1 paths. For queue-depth io-policy we can then refer the "
queue_depth" attribute file created under each namespace path:$ cat /sys/block/nvme1n1/multipath/nvme1c1n1/queue_depth 518$cat
/sys/block/nvme1n1/multipath/nvme1c3n1/queue_depth504Quoted 1 line
From the above output, we can infer that I/O workload targeted at nvme1n1
uses two paths nvme1c1n1 and nvme1c3n1 and the current queue depth of each path is 518 and 504 respectively. Reading "
queue_depth" file when configured io-policy is anything but queue-depth would show no output.
Quoted 8 lines
Reviewed-by Sagi Grimberg <[email protected]>Signed-off-by Nilay Shroff <[email protected]>--- drivers/nvme/host/multipath.c | 12 ++++++++++++ drivers/nvme/host/nvme.h | 1 + drivers/nvme/host/sysfs.c | 3 ++- 3 files changed, 15 insertions(+), 1 deletion(-)
Cheers,
Hannes
Signature · 4 lines
Dr. Hannes Reinecke Kernel Storage Architect [email protected] +49 911 74053 688 SUSE Software Solutions GmbH, Frankenstr. 146, 90461 Nürnberg HRB 36809 (AG Nürnberg), GF: I. Totev, A. McDonald, W. Knoblich
Quoted 7 lines · Nilay Shroff
This RFC propose adding new sysfs attributes for adding visibility of nvme native multipath I/O.
The changes are divided into three patches.
The first patch adds visibility for round-robin io-policy. The second patch adds visibility for numa io-policy. The third patch adds the visibility for queue-depth io-policy.
Thanks, applied to nvme-6.14.