Skip to contentSkip to conversation

Add visibility for native NVMe multipath using sysfs

RFC PATCH Applied Nilay Shroff 3 participants 8 messages Jan 12, 2025 – Jan 24, 2025 NVMe

lore
Share & tools
lore
#1 lore raw

RFC PATCH v7 1/3 nvme-multipath: Add visibility for round-robin io-policy

In reply to Nilay Shroff

This patch helps add nvme native multipath visibility for round-robin io-policy. It creates a "multipath" sysfs directory under head gendisk device node directory and then from "multipath" directory it adds a link to each namespace path device the head node refers.

For instance, if we have a shared namespace accessible from two different controllers/paths then we create a soft link to each path device from head disk node as shown below:

$ ls -l /sys/block/nvme1n1/multipath/
nvme1c1n1 -> ../../../../../pci052e:78/052e:78:00.0/nvme/nvme1/nvme1c1n1
nvme1c3n1 -> ../../../../../pci058e:78/058e:78:00.0/nvme/nvme3/nvme1c3n1

In the above example, nvme1n1 is head gendisk node created for a shared namespace and the namespace is accessible from nvme1c1n1 and nvme1c3n1 paths.

For round-robin I/O policy, we could easily infer from the above output that I/O workload targeted to nvme1n1 would toggle across paths nvme1c1n1 and nvme1c3n1.

---
 drivers/nvme/host/core.c      |  3 ++
 drivers/nvme/host/multipath.c | 99 +++++++++++++++++++++++++++++++++++
 drivers/nvme/host/nvme.h      | 18 +++++--
 drivers/nvme/host/sysfs.c     | 14 +++++
 4 files changed, 130 insertions(+), 4 deletions(-)
drivers/nvme/host/core.c +3 -0
index a970168a3014..f1aa4aa41d17 100644
@@ -3982,6 +3982,9 @@ static void nvme_ns_remove(struct nvme_ns *ns)
 
 	if (!nvme_ns_head_multipath(ns->head))
 		nvme_cdev_del(&ns->cdev, &ns->cdev_device);
+
+	nvme_mpath_remove_sysfs_link(ns);
+
 	del_gendisk(ns->disk);
 
 	mutex_lock(&ns->ctrl->namespaces_lock);
drivers/nvme/host/multipath.c +99 -0

117 lines not on this page · raw message

drivers/nvme/host/nvme.h +14 -4
index c4bb8dfe1a45..643bf580bd09 100644
@@ -534,10 +534,11 @@ struct nvme_ns {
 	struct nvme_ns_head *head;
 
 	unsigned long flags;
-#define NVME_NS_REMOVING	0
-#define NVME_NS_ANA_PENDING	2
-#define NVME_NS_FORCE_RO	3
-#define NVME_NS_READY		4
+#define NVME_NS_REMOVING		0
+#define NVME_NS_ANA_PENDING		2
+#define NVME_NS_FORCE_RO		3
+#define NVME_NS_READY			4
+#define NVME_NS_SYSFS_ATTR_LINK	5
 
 	struct cdev		cdev;
 	struct device		cdev_device;
@@ -933,6 +934,7 @@ int nvme_getgeo(struct block_device *bdev, struct hd_geometry *geo);
 int nvme_dev_uring_cmd(struct io_uring_cmd *ioucmd, unsigned int issue_flags);
 
 extern const struct attribute_group *nvme_ns_attr_groups[];
+extern const struct attribute_group nvme_ns_mpath_attr_group;
 extern const struct pr_ops nvme_pr_ops;
 extern const struct block_device_operations nvme_ns_head_ops;
 extern const struct attribute_group nvme_dev_attrs_group;
@@ -955,6 +957,8 @@ void nvme_mpath_default_iopolicy(struct nvme_subsystem *subsys);
 void nvme_failover_req(struct request *req);
 void nvme_kick_requeue_lists(struct nvme_ctrl *ctrl);
 int nvme_mpath_alloc_disk(struct nvme_ctrl *ctrl,struct nvme_ns_head *head);
+void nvme_mpath_add_sysfs_link(struct nvme_ns_head *ns);
+void nvme_mpath_remove_sysfs_link(struct nvme_ns *ns);
 void nvme_mpath_add_disk(struct nvme_ns *ns, __le32 anagrpid);
 void nvme_mpath_remove_disk(struct nvme_ns_head *head);
 int nvme_mpath_init_identify(struct nvme_ctrl *ctrl, struct nvme_id_ctrl *id);
@@ -1009,6 +1013,12 @@ static inline void nvme_mpath_add_disk(struct nvme_ns *ns, __le32 anagrpid)
 static inline void nvme_mpath_remove_disk(struct nvme_ns_head *head)
 {
 }
+static inline void nvme_mpath_add_sysfs_link(struct nvme_ns *ns)
+{
+}
+static inline void nvme_mpath_remove_sysfs_link(struct nvme_ns *ns)
+{
+}
 static inline bool nvme_mpath_clear_current_path(struct nvme_ns *ns)
 {
 	return false;
drivers/nvme/host/sysfs.c +14 -0
index b68a9e5f1ea3..5a23e23b0d01 100644
@@ -299,8 +299,22 @@ static const struct attribute_group nvme_ns_attr_group = {
 	.is_visible	= nvme_ns_attrs_are_visible,
 };
 
+#ifdef CONFIG_NVME_MULTIPATH
+static struct attribute *nvme_ns_mpath_attrs[] = {
+	NULL,
+};
+
+const struct attribute_group nvme_ns_mpath_attr_group = {
+	.name           = "multipath",
+	.attrs		= nvme_ns_mpath_attrs,
+};
+#endif
+
 const struct attribute_group *nvme_ns_attr_groups[] = {
 	&nvme_ns_attr_group,
+#ifdef CONFIG_NVME_MULTIPATH
+	&nvme_ns_mpath_attr_group,
+#endif
 	NULL,
 };
 
Signature · 1 line
2.47.1
#3 lore raw

RFC PATCH v7 2/3 nvme-multipath: Add visibility for numa io-policy

In reply to Nilay Shroff

This patch helps add nvme native multipath visibility for numa io-policy. It adds a new attribute file named "numa_nodes" under namespace gendisk device path node which prints the list of numa nodes preferred by the given namespace path. The numa nodes value is comma delimited list of nodes or A-B range of nodes.

For instance, if we have a shared namespace accessible from two different controllers/paths then accessing head node of the shared namespace would show the following output:

$ ls -l /sys/block/nvme1n1/multipath/
nvme1c1n1 -> ../../../../../pci052e:78/052e:78:00.0/nvme/nvme1/nvme1c1n1
nvme1c3n1 -> ../../../../../pci058e:78/058e:78:00.0/nvme/nvme3/nvme1c3n1

In the above example, nvme1n1 is head gendisk node created for a shared namespace and this namespace is accessible from nvme1c1n1 and nvme1c3n1 paths. For numa io-policy we can then refer the "numa_nodes" attribute file created under each namespace path:

$ cat /sys/block/nvme1n1/multipath/nvme1c1n1/numa_nodes
0-1
$ cat /sys/block/nvme1n1/multipath/nvme1c3n1/numa_nodes
2-3
Quoted 1 line

From the above output, we infer that I/O workload targeted at nvme1n1

and running on numa nodes 0 and 1 would prefer using path nvme1c1n1. Similarly, I/O workload running on numa nodes 2 and 3 would prefer using path nvme1c3n1. Reading "numa_nodes" file when configured io-policy is anything but numa would show no output.

---
 drivers/nvme/host/multipath.c | 27 +++++++++++++++++++++++++++
 drivers/nvme/host/nvme.h      |  1 +
 drivers/nvme/host/sysfs.c     |  5 +++++
 3 files changed, 33 insertions(+)
drivers/nvme/host/multipath.c +27 -0
index eccc26616e38..3f402a7f4af7 100644
@@ -976,6 +976,33 @@ static ssize_t ana_state_show(struct device *dev, struct device_attribute *attr,
 }
 DEVICE_ATTR_RO(ana_state);
 
+static ssize_t numa_nodes_show(struct device *dev, struct device_attribute *attr,
+		char *buf)
+{
+	int node, srcu_idx;
+	nodemask_t numa_nodes;
+	struct nvme_ns *current_ns;
+	struct nvme_ns *ns = nvme_get_ns_from_dev(dev);
+	struct nvme_ns_head *head = ns->head;
+
+	if (head->subsys->iopolicy != NVME_IOPOLICY_NUMA)
+		return 0;
+
+	nodes_clear(numa_nodes);
+
+	srcu_idx = srcu_read_lock(&head->srcu);
+	for_each_node(node) {
+		current_ns = srcu_dereference(head->current_path[node],
+				&head->srcu);
+		if (ns == current_ns)
+			node_set(node, numa_nodes);
+	}
+	srcu_read_unlock(&head->srcu, srcu_idx);
+
+	return sysfs_emit(buf, "%*pbl\n", nodemask_pr_args(&numa_nodes));
+}
+DEVICE_ATTR_RO(numa_nodes);
+
 static int nvme_lookup_ana_group_desc(struct nvme_ctrl *ctrl,
 		struct nvme_ana_group_desc *desc, void *data)
 {
drivers/nvme/host/nvme.h +1 -0
index 643bf580bd09..fd9f2070d86f 100644
@@ -984,6 +984,7 @@ static inline void nvme_trace_bio_complete(struct request *req)
 extern bool multipath;
 extern struct device_attribute dev_attr_ana_grpid;
 extern struct device_attribute dev_attr_ana_state;
+extern struct device_attribute dev_attr_numa_nodes;
 extern struct device_attribute subsys_attr_iopolicy;
 
 static inline bool nvme_disk_is_ns_head(struct gendisk *disk)
drivers/nvme/host/sysfs.c +5 -0
index 5a23e23b0d01..5a5ee0beb166 100644
@@ -258,6 +258,7 @@ static struct attribute *nvme_ns_attrs[] = {
 #ifdef CONFIG_NVME_MULTIPATH
 	&dev_attr_ana_grpid.attr,
 	&dev_attr_ana_state.attr,
+	&dev_attr_numa_nodes.attr,
 #endif
 	&dev_attr_io_passthru_err_log_enabled.attr,
 	NULL,
@@ -290,6 +291,10 @@ static umode_t nvme_ns_attrs_are_visible(struct kobject *kobj,
 		if (!nvme_ctrl_use_ana(nvme_get_ns_from_dev(dev)->ctrl))
 			return 0;
 	}
+	if (a == &dev_attr_numa_nodes.attr) {
+		if (nvme_disk_is_ns_head(dev_to_disk(dev)))
+			return 0;
+	}
 #endif
 	return a->mode;
 }
Signature · 1 line
2.47.1
#5 lore raw

RFC PATCH v7 3/3 nvme-multipath: Add visibility for queue-depth io-policy

In reply to Nilay Shroff

This patch helps add nvme native multipath visibility for queue-depth io-policy. It adds a new attribute file named "queue_depth" under namespace device path node which would print the number of active/ in-flight I/O requests currently queued for the given path.

For instance, if we have a shared namespace accessible from two different controllers/paths then accessing head block node of the shared namespace would show the following output:

$ ls -l /sys/block/nvme1n1/multipath/
nvme1c1n1 -> ../../../../../pci052e:78/052e:78:00.0/nvme/nvme1/nvme1c1n1
nvme1c3n1 -> ../../../../../pci058e:78/058e:78:00.0/nvme/nvme3/nvme1c3n1

In the above example, nvme1n1 is head gendisk node created for a shared namespace and the namespace is accessible from nvme1c1n1 and nvme1c3n1 paths. For queue-depth io-policy we can then refer the "queue_depth" attribute file created under each namespace path:

$ cat /sys/block/nvme1n1/multipath/nvme1c1n1/queue_depth
518

$cat /sys/block/nvme1n1/multipath/nvme1c3n1/queue_depth 504

Quoted 1 line

From the above output, we can infer that I/O workload targeted at nvme1n1

uses two paths nvme1c1n1 and nvme1c3n1 and the current queue depth of each path is 518 and 504 respectively. Reading "queue_depth" file when configured io-policy is anything but queue-depth would show no output.

---
 drivers/nvme/host/multipath.c | 12 ++++++++++++
 drivers/nvme/host/nvme.h      |  1 +
 drivers/nvme/host/sysfs.c     |  3 ++-
 3 files changed, 15 insertions(+), 1 deletion(-)
drivers/nvme/host/multipath.c +12 -0
index 3f402a7f4af7..d5ff418746f7 100644
@@ -976,6 +976,18 @@ static ssize_t ana_state_show(struct device *dev, struct device_attribute *attr,
 }
 DEVICE_ATTR_RO(ana_state);
 
+static ssize_t queue_depth_show(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct nvme_ns *ns = nvme_get_ns_from_dev(dev);
+
+	if (ns->head->subsys->iopolicy != NVME_IOPOLICY_QD)
+		return 0;
+
+	return sysfs_emit(buf, "%d\n", atomic_read(&ns->ctrl->nr_active));
+}
+DEVICE_ATTR_RO(queue_depth);
+
 static ssize_t numa_nodes_show(struct device *dev, struct device_attribute *attr,
 		char *buf)
 {
drivers/nvme/host/nvme.h +1 -0
index fd9f2070d86f..b536133db361 100644
@@ -984,6 +984,7 @@ static inline void nvme_trace_bio_complete(struct request *req)
 extern bool multipath;
 extern struct device_attribute dev_attr_ana_grpid;
 extern struct device_attribute dev_attr_ana_state;
+extern struct device_attribute dev_attr_queue_depth;
 extern struct device_attribute dev_attr_numa_nodes;
 extern struct device_attribute subsys_attr_iopolicy;
 
drivers/nvme/host/sysfs.c +2 -1
index 5a5ee0beb166..498659efacba 100644
@@ -258,6 +258,7 @@ static struct attribute *nvme_ns_attrs[] = {
 #ifdef CONFIG_NVME_MULTIPATH
 	&dev_attr_ana_grpid.attr,
 	&dev_attr_ana_state.attr,
+	&dev_attr_queue_depth.attr,
 	&dev_attr_numa_nodes.attr,
 #endif
 	&dev_attr_io_passthru_err_log_enabled.attr,
@@ -291,7 +292,7 @@ static umode_t nvme_ns_attrs_are_visible(struct kobject *kobj,
 		if (!nvme_ctrl_use_ana(nvme_get_ns_from_dev(dev)->ctrl))
 			return 0;
 	}
-	if (a == &dev_attr_numa_nodes.attr) {
+	if (a == &dev_attr_queue_depth.attr || a == &dev_attr_numa_nodes.attr) {
 		if (nvme_disk_is_ns_head(dev_to_disk(dev)))
 			return 0;
 	}
Signature · 1 line
2.47.1
#0 lore raw

v7 cover Add visibility for native NVMe multipath using sysfs

Hi,

This RFC propose adding new sysfs attributes for adding visibility of nvme native multipath I/O.

The changes are divided into three patches.
The first patch adds visibility for round-robin io-policy. The second patch adds visibility for numa io-policy. The third patch adds the visibility for queue-depth io-policy.

As we know, NVMe native multipath supports three different io policies (numa, round-robin and queue-depth) for selecting I/O path, however, we don't have any visibility about which path is being selected by multipath code for forwarding I/O. This RFC helps add that visibility by adding new sysfs attribute files named "numa_nodes" and "queue_depth" under each namespace block device path /sys/block/nvmeXcYnZ/. We also create a "multipath" sysfs directory under head disk node and then from this directory add a link to each namespace path device this head disk node points to.

Please find below output generated with this proposed RFC patch applied on a system with two multi-controller PCIe NVMe disks attached to it. This system is also an NVMf-TCP host which is connected to an NVMf-TCP target over two NIC cards. This system has four numa nodes online when the below output was captured:

# cat /sys/devices/system/node/online
0-3
# lscpu
<snip>
NUMA:
  NUMA node(s):           4
  NUMA node0 CPU(s):
  NUMA node1 CPU(s):      0-7
  NUMA node2 CPU(s):      8-31
  NUMA node3 CPU(s):      32-63
<snip>

Please note that numa node 0 though online, doesn't have any CPU currently assigned to it.

# nvme list -v
Subsystem        Subsystem-NQN                                                                                    Controllers
---------------- ------------------------------------------------------------------------------------------------ ----------------
nvme-subsys1     nqn.1994-11.com.samsung:nvme:PM1735a:2.5-inch:S6RTNE0R900057                                     nvme0, nvme1
nvme-subsys3     nqn.2019-10.com.kioxia:KCM7DRUG1T92:3D60A04906N1                                                 nvme2, nvme3
nvme-subsys4     nvmet_subsystem                                                                                  nvme4, nvme5

Device Cntlid SN MN FR TxPort Address Slot Subsystem Namespaces
---------------- ------ -------------------- ---------------------------------------- -------- ------ -------------- ------ ------------ ----------------

nvme0    66     S6RTNE0R900057       3.2TB NVMe Gen4 U.2 SSD III              REV.SN66 pcie   052e:78:00.0   U50EE.001.WZS000E-P3-C14-R1 nvme-subsys1 nvme1n1
nvme1    65     S6RTNE0R900057       3.2TB NVMe Gen4 U.2 SSD III              REV.SN66 pcie   058e:78:00.0   U50EE.001.WZS000E-P3-C14-R2 nvme-subsys1 nvme1n1
nvme2    2      3D60A04906N1         1.6TB NVMe Gen4 U.2 SSD IV               REV.CAS2 pcie   0524:28:00.0   U50EE.001.WZS000E-P3-C4-R1 nvme-subsys3 nvme3n1
nvme3    1      3D60A04906N1         1.6TB NVMe Gen4 U.2 SSD IV               REV.CAS2 pcie   0584:28:00.0   U50EE.001.WZS000E-P3-C4-R2 nvme-subsys3 nvme3n1
nvme4    1      a224673364d1dcb6fab9 Linux                                    6.9.0-rc tcp    traddr=20.0.0.200,trsvcid=4420,src_addr=20.0.0.100        nvme-subsys4 nvme4n1
nvme5    2      a224673364d1dcb6fab9 Linux                                    6.9.0-rc tcp    traddr=10.0.0.200,trsvcid=4420,src_addr=10.0.0.100        nvme-subsys4 nvme4n1

Device Generic NSID Usage Format Controllers
----------------- ----------------- ---------- -------------------------- ---------------- ----------------

/dev/nvme1n1 /dev/ng1n1   0x1          5.75  GB /   5.75  GB      4 KiB +  0 B   nvme0, nvme1
/dev/nvme3n1 /dev/ng3n1   0x2          0.00   B /   5.75  GB      4 KiB +  0 B   nvme2, nvme3
/dev/nvme4n1 /dev/ng4n1   0x1          5.75  GB /   5.75  GB      4 KiB +  0 B   nvme4, nvme5
# nvme show-topology
nvme-subsys1 - NQN=nqn.1994-11.com.samsung:nvme:PM1735a:2.5-inch:S6RTNE0R900057
               hostnqn=nqn.2014-08.org.nvmexpress:uuid:41528538-e8ad-4eaf-84a7-9c552917d988
               iopolicy=numa
\
 +- ns 1
 \
  +- nvme0 pcie 052e:78:00.0 live optimized
  +- nvme1 pcie 058e:78:00.0 live optimized

nvme-subsys3 - NQN=nqn.2019-10.com.kioxia:KCM7DRUG1T92:3D60A04906N1

               hostnqn=nqn.2014-08.org.nvmexpress:uuid:41528538-e8ad-4eaf-84a7-9c552917d988
               iopolicy=round-robin
\
 +- ns 2
 \
  +- nvme2 pcie 0524:28:00.0 live optimized
  +- nvme3 pcie 0584:28:00.0 live optimized

nvme-subsys4 - NQN=nvmet_subsystem

               hostnqn=nqn.2014-08.org.nvmexpress:uuid:41528538-e8ad-4eaf-84a7-9c552917d988
               iopolicy=queue-depth
\
 +- ns 1
 \
  +- nvme4 tcp traddr=20.0.0.200,trsvcid=4420,src_addr=20.0.0.100 live optimized
  +- nvme5 tcp traddr=10.0.0.200,trsvcid=4420,src_addr=10.0.0.100 live optimized

As we could see above, we've three shared namespaces created. In terms of iopolicy, we have "numa" configured for nvme-subsys1, "round-robin" configured for nvme-subsys3 and "queue-depth" configured for nvme-subsys4.

Now, under each namespace "head disk node", we create a sysfs group attribute named "multipath". The "multipath" group then points to the each path this head disk node points to:

# tree /sys/block/nvme1n1/multipath/
/sys/block/nvme1n1/multipath/
├── nvme1c0n1 -> ../../../../../pci052e:78/052e:78:00.0/nvme/nvme0/nvme1c0n1
└── nvme1c1n1 -> ../../../../../pci058e:78/058e:78:00.0/nvme/nvme1/nvme1c1n1
# tree /sys/block/nvme3n1/multipath/
/sys/block/nvme3n1/multipath/
├── nvme3c2n1 -> ../../../../../pci0524:28/0524:28:00.0/nvme/nvme2/nvme3c2n1
└── nvme3c3n1 -> ../../../../../pci0584:28/0584:28:00.0/nvme/nvme3/nvme3c3n1
# tree /sys/block/nvme4n1/multipath/
/sys/block/nvme4n1/multipath/
├── nvme4c4n1 -> ../../../../nvme-fabrics/ctl/nvme4/nvme4c4n1
└── nvme4c5n1 -> ../../../../nvme-fabrics/ctl/nvme5/nvme4c5n1

One can easily infer from the above output that for the "round-robin" I/O policy, configured under nvme-subsys3, the I/O workload targeted at nvme3n1 would toggle across nvme3c2n1 and nvme3c3n1 assuming the ana state of each path is optimized (as can be seen in the output of show-topology).

For numa I/O policy, configured under nvme-subsys1, the "numa_nodes" attribute file shows the numa nodes being preferred by the respective namespace path. The numa nodes value is comma delimited list of nodes or A-B range of nodes.

# cat  /sys/block/nvme1n1/multipath/nvme1c0n1/numa_nodes
0-1
# cat  /sys/block/nvme1n1/multipath/nvme1c1n1/numa_nodes
2-3

From the above output, one can easily infer that I/O workload targeted at nvme1n1 and running on numa nodes 0 and 1 would use path nvme1c0n1. Similarly, I/O workload running on numa nodes 2 and 3 would use path nvme1c1n1.

For queue-depth I/O policy, configured under nvme-subsys4, the "queue_depth" attribute file shows the number of active/in-flight I/O requests currently queued for each path.

# cat  /sys/block/nvme4n1/multipath/nvme4c4n1/queue_depth
518
# cat  /sys/block/nvme4n1/multipath/nvme4c5n1/queue_depth
504

From the above output, one can easily infer that I/O workload targeted at nvme4n1 uses two paths nvme4c4n1 and nvme4c5n1 and the current queue depth of each path is 518 and 504 respectively.

Changes since v6:
- Fix sysfs link warning menifested while running blktest nvme/058 (Keith Busch, Chaitanya Kulkarni)
- Link to v6: https://lore.kernel.org/all/[email protected]/
Changes since v5:
- Fix typo in the subject line of the first patch in the series (Danied Wagner)
- Link to v5: https://lore.kernel.org/all/[email protected]/
changes since v4:
- Ensure that we create sysfs link from head gendisk node to each path device irrespective of the ANA state of the path (Hannes Reinecke)
- Split the patch into three patch series and add commentary in the
code so that it's easy to read and understand the core logic (Sagi Grimberg)
- Don't show any output if user reads "numa_nodes" file and configured iopolicy is anything but numa; similarly don't emit any output if user reads "queue_depth" file and configured iopolicy is anything but queue-depth (Sagi Grimberg)
- Link to v4: https://lore.kernel.org/all/[email protected]/

Changes since v3:
- Protect the namespace dereference code with srcu read lock (Daniel Wagner)
- Link to v3: https://lore.kernel.org/all/[email protected]/

Changes since v2:
- Use one value per one sysfs attribute (Keith Busch)
- Link to v2: https://lore.kernel.org/all/[email protected]/

Changes since v1:
- Use sysfs to export multipath I/O information instead of debugfs
- Link to v1: https://lore.kernel.org/all/[email protected]/

Nilay Shroff (3):
nvme-multipath: Add visibility for round-robin io-policy
nvme-multipath: Add visibility for numa io-policy
nvme-multipath: Add visibility for queue-depth io-policy

 drivers/nvme/host/core.c      |   3 +
 drivers/nvme/host/multipath.c | 138 ++++++++++++++++++++++++++++++++++
 drivers/nvme/host/nvme.h      |  20 ++++-
 drivers/nvme/host/sysfs.c     |  20 +++++
 4 files changed, 177 insertions(+), 4 deletions(-)
Signature · 1 line
2.47.1
Reviewed-by on v7 1/3
#2 lore raw

Re: [PATCHv7 RFC 1/3] nvme-multipath: Add visibility for round-robin io-policy

In reply to Nilay Shroff
Quoted 21 lines · Nilay Shroff

This patch helps add nvme native multipath visibility for round-robin io-policy. It creates a "multipath" sysfs directory under head gendisk device node directory and then from "multipath" directory it adds a link to each namespace path device the head node refers.

For instance, if we have a shared namespace accessible from two different controllers/paths then we create a soft link to each path device from head disk node as shown below:

$ ls -l /sys/block/nvme1n1/multipath/
nvme1c1n1 -> ../../../../../pci052e:78/052e:78:00.0/nvme/nvme1/nvme1c1n1
nvme1c3n1 -> ../../../../../pci058e:78/058e:78:00.0/nvme/nvme3/nvme1c3n1

In the above example, nvme1n1 is head gendisk node created for a shared namespace and the namespace is accessible from nvme1c1n1 and nvme1c3n1 paths.

For round-robin I/O policy, we could easily infer from the above output that I/O workload targeted to nvme1n1 would toggle across paths nvme1c1n1 and nvme1c3n1.

Quoted 8 lines
---
  drivers/nvme/host/core.c      |  3 ++
  drivers/nvme/host/multipath.c | 99 +++++++++++++++++++++++++++++++++++
  drivers/nvme/host/nvme.h      | 18 +++++--
  drivers/nvme/host/sysfs.c     | 14 +++++
  4 files changed, 130 insertions(+), 4 deletions(-)

Cheers,

Hannes

Signature · 4 lines
Dr. Hannes Reinecke                  Kernel Storage Architect
[email protected]                                +49 911 74053 688
SUSE Software Solutions GmbH, Frankenstr. 146, 90461 Nürnberg
HRB 36809 (AG Nürnberg), GF: I. Totev, A. McDonald, W. Knoblich
Reviewed-by on v7 2/3
#4 lore raw

Re: [PATCHv7 RFC 2/3] nvme-multipath: Add visibility for numa io-policy

In reply to Nilay Shroff
Quoted 31 lines · Nilay Shroff

This patch helps add nvme native multipath visibility for numa io-policy. It adds a new attribute file named "numa_nodes" under namespace gendisk device path node which prints the list of numa nodes preferred by the given namespace path. The numa nodes value is comma delimited list of nodes or A-B range of nodes.

For instance, if we have a shared namespace accessible from two different controllers/paths then accessing head node of the shared namespace would show the following output:

$ ls -l /sys/block/nvme1n1/multipath/
nvme1c1n1 -> ../../../../../pci052e:78/052e:78:00.0/nvme/nvme1/nvme1c1n1
nvme1c3n1 -> ../../../../../pci058e:78/058e:78:00.0/nvme/nvme3/nvme1c3n1

In the above example, nvme1n1 is head gendisk node created for a shared namespace and this namespace is accessible from nvme1c1n1 and nvme1c3n1 paths. For numa io-policy we can then refer the "numa_nodes" attribute file created under each namespace path:

$ cat /sys/block/nvme1n1/multipath/nvme1c1n1/numa_nodes
0-1
$ cat /sys/block/nvme1n1/multipath/nvme1c3n1/numa_nodes
2-3
Quoted 1 line

From the above output, we infer that I/O workload targeted at nvme1n1

and running on numa nodes 0 and 1 would prefer using path nvme1c1n1. Similarly, I/O workload running on numa nodes 2 and 3 would prefer using path nvme1c3n1. Reading "numa_nodes" file when configured io-policy is anything but numa would show no output.

Quoted 8 lines
---
  drivers/nvme/host/multipath.c | 27 +++++++++++++++++++++++++++
  drivers/nvme/host/nvme.h      |  1 +
  drivers/nvme/host/sysfs.c     |  5 +++++
  3 files changed, 33 insertions(+)

Cheers,

Hannes

Signature · 4 lines
Dr. Hannes Reinecke                  Kernel Storage Architect
[email protected]                                +49 911 74053 688
SUSE Software Solutions GmbH, Frankenstr. 146, 90461 Nürnberg
HRB 36809 (AG Nürnberg), GF: I. Totev, A. McDonald, W. Knoblich
Reviewed-by on v7 3/3
#6 lore raw

Re: [PATCHv7 RFC 3/3] nvme-multipath: Add visibility for queue-depth io-policy

In reply to Nilay Shroff
Quoted 29 lines · Nilay Shroff

This patch helps add nvme native multipath visibility for queue-depth io-policy. It adds a new attribute file named "queue_depth" under namespace device path node which would print the number of active/ in-flight I/O requests currently queued for the given path.

For instance, if we have a shared namespace accessible from two different controllers/paths then accessing head block node of the shared namespace would show the following output:

$ ls -l /sys/block/nvme1n1/multipath/
nvme1c1n1 -> ../../../../../pci052e:78/052e:78:00.0/nvme/nvme1/nvme1c1n1
nvme1c3n1 -> ../../../../../pci058e:78/058e:78:00.0/nvme/nvme3/nvme1c3n1

In the above example, nvme1n1 is head gendisk node created for a shared namespace and the namespace is accessible from nvme1c1n1 and nvme1c3n1 paths. For queue-depth io-policy we can then refer the "queue_depth" attribute file created under each namespace path:

$ cat /sys/block/nvme1n1/multipath/nvme1c1n1/queue_depth
518

$cat /sys/block/nvme1n1/multipath/nvme1c3n1/queue_depth 504

Quoted 1 line

From the above output, we can infer that I/O workload targeted at nvme1n1

uses two paths nvme1c1n1 and nvme1c3n1 and the current queue depth of each path is 518 and 504 respectively. Reading "queue_depth" file when configured io-policy is anything but queue-depth would show no output.

Quoted 8 lines
---
  drivers/nvme/host/multipath.c | 12 ++++++++++++
  drivers/nvme/host/nvme.h      |  1 +
  drivers/nvme/host/sysfs.c     |  3 ++-
  3 files changed, 15 insertions(+), 1 deletion(-)

Cheers,

Hannes

Signature · 4 lines
Dr. Hannes Reinecke                  Kernel Storage Architect
[email protected]                                +49 911 74053 688
SUSE Software Solutions GmbH, Frankenstr. 146, 90461 Nürnberg
HRB 36809 (AG Nürnberg), GF: I. Totev, A. McDonald, W. Knoblich
maintainer Applied
#7 lore raw
In reply to Nilay Shroff
Quoted 7 lines · Nilay Shroff

This RFC propose adding new sysfs attributes for adding visibility of nvme native multipath I/O.

The changes are divided into three patches.
The first patch adds visibility for round-robin io-policy. The second patch adds visibility for numa io-policy. The third patch adds the visibility for queue-depth io-policy.

Thanks, applied to nvme-6.14.