Skip to contentSkip to conversation

Initial attempt at flashing instructions.

PATCH Superseded [email protected] 3 participants 8 messages Jun 25, 2017 – Jun 28, 2017

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

v2 cover Initial attempt at flashing instructions.

From: Drew Moseley <[email protected]>

* V2:

Updated README and layer dependencies.

Added error checking to flashing script

* V1:

This set of patches adds the native tools and target components needed to reflash the CHIP boards. Additionally a shell script is added to the deploy directory showing how to kick off a flash update. It's not ideal as I've hardcoded a max size for the UBI image into the script and didn't see much of an alternative. It does function though.

Drew

The following changes since commit 0079e6ac10fc371d6f527270c23b887561f717aa:

chip: Append to MACHINE_EXTRA_RRECOMMENDS rather than overwriting (2017-06-15 13:37:19 +0100)

are available in the git repository at:

[email protected]:drewmoseley/meta-chip.git flashing-instructions-v2

for you to fetch changes up to ddbfd00d73ea022aaa02005393a326d8802dd64a:

chip: Add chip-u-boot-scr recipe and flash script (2017-06-25 15:28:54 -0400)

----------------------------------------------------------------
Drew Moseley (3):
u-boot-chip: Deploy the sunxi-spl-with-ecc.bin file.
chip: Build sunxi-tools-native.
chip: Add chip-u-boot-scr recipe and flash script

 README                                          | 94 ++++++++++++++++++++++++-
 conf/layer.conf                                 |  3 +
 conf/machine/chip.conf                          |  3 +-
 recipes-bsp/chip-u-boot-scr/chip-u-boot-scr.bb  | 89 +++++++++++++++++++++++
 recipes-bsp/chip-u-boot-scr/files/boot.cmd.full | 32 +++++++++
 recipes-bsp/chip-u-boot-scr/files/boot.cmd.in   | 43 +++++++++++
 recipes-bsp/u-boot/u-boot-chip_git.bb           |  7 ++
 7 files changed, 269 insertions(+), 2 deletions(-)
 create mode 100644 recipes-bsp/chip-u-boot-scr/chip-u-boot-scr.bb
 create mode 100644 recipes-bsp/chip-u-boot-scr/files/boot.cmd.full
 create mode 100644 recipes-bsp/chip-u-boot-scr/files/boot.cmd.in

Drew Moseley (3):
u-boot-chip: Deploy the sunxi-spl-with-ecc.bin file.
chip: Build sunxi-tools-native.
chip: Add chip-u-boot-scr recipe and flash script

 README                                          | 94 ++++++++++++++++++++++++-
 conf/layer.conf                                 |  3 +
 conf/machine/chip.conf                          |  3 +-
 recipes-bsp/chip-u-boot-scr/chip-u-boot-scr.bb  | 89 +++++++++++++++++++++++
 recipes-bsp/chip-u-boot-scr/files/boot.cmd.full | 32 +++++++++
 recipes-bsp/chip-u-boot-scr/files/boot.cmd.in   | 43 +++++++++++
 recipes-bsp/u-boot/u-boot-chip_git.bb           |  7 ++
 7 files changed, 269 insertions(+), 2 deletions(-)
 create mode 100644 recipes-bsp/chip-u-boot-scr/chip-u-boot-scr.bb
 create mode 100644 recipes-bsp/chip-u-boot-scr/files/boot.cmd.full
 create mode 100644 recipes-bsp/chip-u-boot-scr/files/boot.cmd.in
Signature · 1 line
2.7.4
#1 lore raw

PATCH v2 1/3 u-boot-chip: Deploy the sunxi-spl-with-ecc.bin file.

From: Drew Moseley <[email protected]>

---
 conf/machine/chip.conf                | 1 +
 recipes-bsp/u-boot/u-boot-chip_git.bb | 6 ++++++
 2 files changed, 7 insertions(+)
conf/machine/chip.conf +1 -0
index 0a45a2f..8f54067 100644
@@ -21,6 +21,7 @@ KERNEL_IMAGETYPE = "zImage"
 KERNEL_DEVICETREE = "sun5i-r8-chip.dtb"
 
 SPL_BINARY = "sunxi-spl.bin"
+SPL_ECC_BINARY = "sunxi-spl-with-ecc.bin"
 UBOOT_BINARY = "u-boot-dtb.bin"
 UBOOT_MACHINE = "CHIP_defconfig"
 
recipes-bsp/u-boot/u-boot-chip_git.bb +6 -0
index 8e2be50..f12fae6 100644
@@ -19,7 +19,13 @@ SRC_URI = " \
 S = "${WORKDIR}/git"
 
 do_compile_append() {
+    install ${B}/spl/${SPL_ECC_BINARY} ${B}/${SPL_ECC_BINARY}
     install ${B}/spl/${SPL_BINARY} ${B}/${SPL_BINARY}
 }
 
 COMPATIBLE_MACHINE = "chip"
+
+do_deploy_append() {
+    install -m 644 ${B}/${SPL_ECC_BINARY} ${DEPLOYDIR}/${SPL_ECC_BINARY}-${PV}-${PR}
+    ln -sf ${SPL_ECC_BINARY}-${PV}-${PR} ${DEPLOYDIR}/${SPL_ECC_BINARY}
+}
\ No newline at end of file
Signature · 1 line
2.7.4
#2 lore raw

PATCH v2 2/3 chip: Build sunxi-tools-native.

In reply to [email protected]

From: Drew Moseley <[email protected]>

Add LAYERDEPENDS on meta-sunxi and add the sunxi-tools-native pacakage to EXTRA_IMAGEDEPENDS.

---
 README                 | 3 +++
 conf/layer.conf        | 3 +++
 conf/machine/chip.conf | 2 +-
 3 files changed, 7 insertions(+), 1 deletion(-)
README +3 -0
index cccf59e..32f70b2 100644
@@ -14,6 +14,9 @@ This layer depends on:
   layers: meta
   branch: master
 
+  URI: git://github.com/linux-sunxi/meta-sunxi.git
+  branch: master
+
 
 Patches
 =======
conf/layer.conf +3 -0
index 5dad66e..3324908 100644
@@ -8,3 +8,6 @@ BBFILES += "${LAYERDIR}/recipes-*/*/*.bb \
 BBFILE_COLLECTIONS += "meta-chip"
 BBFILE_PATTERN_meta-chip = "^${LAYERDIR}/"
 BBFILE_PRIORITY_meta-chip = "6"
+
+# Add this to get access to sunxi-tools recipe
+LAYERDEPENDS_meta-chip = "meta-sunxi"
\ No newline at end of file
conf/machine/chip.conf +1 -1
index 8f54067..ae166f9 100644
@@ -5,7 +5,7 @@
 MACHINE_EXTRA_RRECOMMENDS = " kernel-modules"
 MACHINE_ESSENTIAL_EXTRA_RDEPENDS = " kernel-image kernel-devicetree"
 
-EXTRA_IMAGEDEPENDS += "u-boot"
+EXTRA_IMAGEDEPENDS += "u-boot sunxi-tools-native"
 
 DEFAULTTUNE ?= "cortexa8t-neon"
 include conf/machine/include/tune-cortexa8.inc
Signature · 1 line
2.7.4
#3 lore raw

PATCH v2 3/3 chip: Add chip-u-boot-scr recipe and flash script

In reply to [email protected]

From: Drew Moseley <[email protected]>

Add a U-Boot script to handle flashing the SPL, U-Boot and UBI root filesystem images into the onboard flash. Also generate a script showing how to execute the flash steps.

---
 README                                          | 91 ++++++++++++++++++++++++-
 recipes-bsp/chip-u-boot-scr/chip-u-boot-scr.bb  | 89 ++++++++++++++++++++++++
 recipes-bsp/chip-u-boot-scr/files/boot.cmd.full | 32 +++++++++
 recipes-bsp/chip-u-boot-scr/files/boot.cmd.in   | 43 ++++++++++++
 recipes-bsp/u-boot/u-boot-chip_git.bb           |  1 +
 5 files changed, 255 insertions(+), 1 deletion(-)
 create mode 100644 recipes-bsp/chip-u-boot-scr/chip-u-boot-scr.bb
 create mode 100644 recipes-bsp/chip-u-boot-scr/files/boot.cmd.full
 create mode 100644 recipes-bsp/chip-u-boot-scr/files/boot.cmd.in
README +90 -1
index 32f70b2..d3ab815 100644
@@ -62,4 +62,93 @@ To build a machine supported by this BSP layer follow the next steps:
 II. Flashing a C.H.I.P. board
 ========================================
 
-<TODO>
+As part of the build including this BSP layer, a U-Boot script and a
+shell script are created to assist in flashing your images to the CHIP
+board.  Note that this script assumes a maximum size for your UBI
+image of 167772160 (0x0A000000) bytes.  If your UBI image exceeds
+that, then you will need to adapt this to your environment.
+
+To successfully run this script you will first need to set your board
+into FEL mode. Insert a wire into the U14 header between pin 7 (FEL)
+and GND.  Then connect the board with a USB cable to your build
+system. More details here:
+    https://docs.getchip.com/chip.html#flash-chip-with-an-os
+
+You need to specify the base filename of your UBI image using the
+UBI_IMAGE shell variable before invoking the generated script as
+follows:
+
+# UBI_IMAGE=chip-hwup-image-chip.ubi \
+        ./tmp/deploy/images/chip/flash_CHIP_board.sh
+
+This script will take some time to execute.  The output of this script
+as run on your host machine should look similar to the following:
+
+    # UBI_IMAGE=chip-hwup-image-chip.ubi ./build/chip/tmp/deploy/images/chip/flash_CHIP_board.sh
+    100% [================================================]  3537 kB,  513.9 kB/s
+    100% [================================================]   619 kB,  551.1 kB/s
+    100% [================================================]     2 kB,  476.0 kB/s
+    100% [================================================] 71303 kB,  531.1 kB/s
+
+If you have a serial console connected to your board, you will see
+progress and a message on the console indicating when flashing is
+complete:
+
+    U-Boot 2016.01 (Jun 20 2017 - 02:54:42 -0400) Allwinner Technology
+    
+    CPU:   Allwinner A13 (SUN5I)
+    I2C:   ready
+    DRAM:  512 MiB
+    NAND:  8192 MiB
+    video-mode 720x480-24@60 not available, falling back to 1024x768-24@60
+    Setting up a 720x480i composite-ntsc console (overscan 40x20)
+    In:    serial
+    Out:   serial
+    Err:   serial
+    Net:   usb_ether
+    starting USB...
+    No controllers found
+    Hit any key to stop autoboot:  0
+    (FEL boot)
+    ## Executing script at 43100000
+    Erasing NAND
+    
+    NAND erase.chip: device 0 whole chip
+    Skipping bad block at  0xeb000000
+    Skipping bad block at  0x1b1000000
+    Erasing at 0x1ffc00000 -- 100% complete.
+    OK
+    Writing SPL (with ECC) to NAND address 0x00000000
+    
+    NAND write:  3537408 bytes written: OK
+    Writing SPL (with ECC) to NAND address 0x400000
+    
+    NAND write:  3537408 bytes written: OK
+    Writing UBoot image to address 0x800000
+    
+    NAND write: device 0 offset 0x800000, size 0x97236
+     619062 bytes written: OK
+    Enabling Splash
+    Setting Video Mode
+    Saving default environment
+    Saving Environment to NAND...
+    Erasing NAND...
+    Erasing at 0xc00000 -- 100% complete.
+    Writing to NAND... OK
+    Writing UBI rootfs to NAND address 0x1000000
+    
+    NAND write: device 0 offset 0x1000000, size 0xa000000
+     167772160 bytes written: OK
+    ===========================================================
+    Flashing Complete. Please power down and disable FEL mode.
+    ===========================================================
+
+Additionally, once the image is properly flashed, the status LED on
+the CHIP board will flash on and off every 2 seconds. This indicates
+that it is safe to power down your board and disable FEL mode.
+
+WARNING: This will erase the entire contents of your CHIP board.
+
+NOTE: This setup is still compatible with the CHIP flashing utility
+available at http://flash.getchip.com if you choose to reinstall the
+stock images.
recipes-bsp/chip-u-boot-scr/chip-u-boot-scr.bb new file +89 -0

89 lines not on this page · raw message

recipes-bsp/chip-u-boot-scr/files/boot.cmd.full new file +32 -0
new file mode 100644
index 0000000..9589c87
@@ -0,0 +1,32 @@
+echo Scrubbing NAND
+nand scrub -y 0x0 0x200000000
+echo Writing SPL (with ECC) to NAND address 0x0
+nand write.raw.noverify $SPL_MEM_ADDR 0x0 $PADDED_SPL_SIZE
+echo Writing SPL (with ECC) to NAND address 0x400000
+nand write.raw.noverify $SPL_MEM_ADDR 0x400000 $PADDED_SPL_SIZE
+echo Writing UBoot image to address 0x800000
+nand write $UBOOT_MEM_ADDR 0x800000 $PADDED_UBOOT_SIZE
+
+# Setup the default environment
+setenv bootargs root=ubi0:rootfs rootfstype=ubifs rw earlyprintk ubi.mtd=4
+setenv bootcmd 'mtdparts; ubi part UBI; ubifsmount ubi0:rootfs; ubifsload \$fdt_addr_r /boot/sun5i-r8-chip.dtb; ubifsload \$kernel_addr_r /boot/zImage; bootz \$kernel_addr_r - \$fdt_addr_r'
+setenv fel_booted 0
+
+echo Enabling Splash
+setenv stdout serial
+setenv stderr serial
+setenv splashpos m,m
+
+echo Setting Video Mode
+setenv video-mode sunxi:640x480-24@60,monitor=composite-ntsc,overscan_x=40,overscan_y=20
+
+echo Saving default environment
+saveenv
+
+echo Writing UBI rootfs to NAND address 0x1000000
+nand write.slc-mode.trimffs $UBI_MEM_ADDR 0x1000000 $UBI_SIZE
+
+echo ===========================================================
+echo Flashing Complete.  Please power down and disable FEL mode.
+echo ===========================================================
+
recipes-bsp/chip-u-boot-scr/files/boot.cmd.in new file +43 -0

43 lines not on this page · raw message

recipes-bsp/u-boot/u-boot-chip_git.bb +1 -0
index f12fae6..008f346 100644
@@ -6,6 +6,7 @@ LIC_FILES_CHKSUM = "file://Licenses/README;md5=0507cd7da8e7ad6d6701926ec9b84c95"
 
 DEPENDS += "dtc-native"
 PROVIDES += "u-boot"
+RDEPENDS_${PN}_append_chip = " chip-u-boot-scr"
 
 UBOOT_VERSION ?= "2016.01"
 PV = "${UBOOT_VERSION}+git${SRCPV}"
Signature · 1 line
2.7.4
Tested-by on the v2 series
#4 lore raw
In reply to [email protected]
Quoted 8 lines · On Sun, Jun 25, 2017 at 3:55 PM, <[email protected]> wrote:

From: Drew Moseley <[email protected]>

* V2:

Updated README and layer dependencies.

Added error checking to flashing script

Quoted 7 lines

* V1:

This set of patches adds the native tools and target components needed to reflash the CHIP boards. Additionally a shell script is added to the deploy directory showing how to kick off a flash update. It's not ideal as I've hardcoded a max size for the UBI image into the script and didn't see much of an alternative. It does function though.

Looks and works great! Thanks for investigating and getting this working :-)

#5 lore raw

Andrei,

Will you need Drew to submit this as a pull request via github?

Best regards,
Trevor

#6 lore raw
In reply to Trevor Woerner
Quoted 21 lines · Trevor Woerner
Quoted 8 lines · On Sun, Jun 25, 2017 at 3:55 PM, <[email protected]> wrote:

From: Drew Moseley <[email protected]>

* V2:

Updated README and layer dependencies.

Added error checking to flashing script

Quoted 7 lines

* V1:

This set of patches adds the native tools and target components needed to reflash the CHIP boards. Additionally a shell script is added to the deploy directory showing how to kick off a flash update. It's not ideal as I've hardcoded a max size for the UBI image into the script and didn't see much of an alternative. It does function though.

Quoted 3 lines

Looks and works great! Thanks for investigating and getting this working :-)

FYI, additional discussion is ongoing at https://github.com/agherzan/meta-chip/pull/9 <https://github.com/agherzan/meta-chip/pull/9>. I’ll have a V3 in a few days. The V3 changes are primarily cosmetic.

Drew

#7 lore raw
Quoted 27 lines · Drew Moseley

On Jun 28, 2017, at 9:03 AM, Trevor Woerner <[email protected]> wrote:

On Sun, Jun 25, 2017 at 3:55 PM, <[email protected]> wrote:

From: Drew Moseley <[email protected]>

* V2:

Updated README and layer dependencies.

Added error checking to flashing script

* V1:

This set of patches adds the native tools and target components needed to reflash the CHIP boards. Additionally a shell script is added to the deploy
directory showing how to kick off a flash update. It's not ideal as I've hardcoded a max size for the UBI image into the script and didn't see much of an alternative. It does function though.

Looks and works great! Thanks for investigating and getting this working :-)

Quoted 7 lines

FYI, additional discussion is ongoing at https://github.com/
agherzan/meta-chip/pull/9. I’ll have a V3 in a few days. The V3 changes are primarily cosmetic.

Correct. There are some small things to tweak. Nothing major and it will get in soon.
--
Andrei Gherzan