stmmac: Add Loongson platform support
Subsystems (5)
v7 cover stmmac: Add Loongson platform support
v7:
* Refer to andrew's suggestion:
- Add DMA_INTR_ENA_NIE_RX and DMA_INTR_ENA_NIE_TX #define's, etc.
* Others:
- Using --subject-prefix="PATCH net-next vN" to indicate that the patches are for the networking tree.
- Rebase to the latest networking tree:
<git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git>
v6:
* Refer to Serge's suggestion:
- Add new platform feature flag:
include/linux/stmmac.h:
+#define STMMAC_FLAG_HAS_LGMAC BIT(13)- Add the IRQs macros specific to the Loongson Multi-channels GMAC:
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h:
+#define DMA_INTR_ENA_NIE_LOONGSON 0x00060000 /* Normal Loongson Tx/Rx Summary */
#define DMA_INTR_ENA_NIE 0x00010000 /* Normal Summary */
... - Drop all of redundant changes that don't require the prototypes being converted to accepting the stmmac_priv pointer.
* Refer to andrew's suggestion:
- Drop white space changes.
- break patch up into lots of smaller parts.
Some small patches have been put into another series as a preparation see <https://lore.kernel.org/loongarch/[email protected]/T/#t>
*note* : This series of patches relies on the three small patches above.
* others
- Drop irq_flags changes.
- Changed patch order.
v4 -> v5:
* Remove an ugly and useless patch (fix channel number).
* Remove the non-standard dma64 driver code, and also remove the HWIF entries, since the associated custom callbacks no longer exist.
* Refer to Serge's suggestion: Update the dwmac1000_dma.c to support the multi-DMA-channels controller setup.
See:
v4: <https://lore.kernel.org/loongarch/[email protected]/>
v3: <https://lore.kernel.org/loongarch/[email protected]/>
v2: <https://lore.kernel.org/loongarch/[email protected]/>
v1: <https://lore.kernel.org/loongarch/[email protected]/>
Yanteng Si (9):
net: stmmac: Pass stmmac_priv and chan in some callbacks
net: stmmac: dwmac-loongson: Refactor code for loongson_dwmac_probe()
net: stmmac: dwmac-loongson: Add full PCI support
net: stmmac: Add multi-channel supports
net: stmmac: Add Loongson-specific register definitions
net: stmmac: dwmac-loongson: Add MSI support
net: stmmac: dwmac-loongson: Add GNET support
net: stmmac: dwmac-loongson: Disable flow control for GMAC
net: stmmac: Disable coe for some Loongson GNET
drivers/net/ethernet/stmicro/stmmac/common.h | 1 + .../ethernet/stmicro/stmmac/dwmac-loongson.c | 296 ++++++++++++++---- .../net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 2 +- .../ethernet/stmicro/stmmac/dwmac1000_dma.c | 61 +++- .../ethernet/stmicro/stmmac/dwmac100_dma.c | 2 +- .../net/ethernet/stmicro/stmmac/dwmac4_dma.c | 2 +- .../net/ethernet/stmicro/stmmac/dwmac_dma.h | 55 +++- .../net/ethernet/stmicro/stmmac/dwmac_lib.c | 68 ++-- .../ethernet/stmicro/stmmac/dwxgmac2_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/hwif.c | 8 +- drivers/net/ethernet/stmicro/stmmac/hwif.h | 11 +- .../ethernet/stmicro/stmmac/stmmac_ethtool.c | 6 + .../net/ethernet/stmicro/stmmac/stmmac_main.c | 13 +- include/linux/stmmac.h | 4 + 14 files changed, 424 insertions(+), 107 deletions(-)
Signature · 1 line
2.31.4
PATCH v7 1/9 net: stmmac: Pass stmmac_priv and chan in some callbacks
Loongson GMAC and GNET have some special features. To prepare for that, pass stmmac_priv and chan to more callbacks, and adjust the callbacks accordingly.
--- drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h | 3 ++- drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c | 3 ++- drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/hwif.h | 11 ++++++----- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 6 +++--- 9 files changed, 18 insertions(+), 15 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +1 -1
@@ -395,7 +395,7 @@ static void sun8i_dwmac_dma_start_tx(struct stmmac_priv *priv,writel (v, ioaddr +EMAC_TX_CTL1 ); } -static void sun8i_dwmac_enable_dma_transmission (void __iomem *ioaddr) +static void sun8i_dwmac_enable_dma_transmission (void __iomem *ioaddr,u32 chan) {u32 v;
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +1 -1
@@ -70,7 +70,7 @@ static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi)writel (value, ioaddr +DMA_AXI_BUS_MODE ); } -static void dwmac1000_dma_init (void __iomem *ioaddr, +static void dwmac1000_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,int atds) {u32 value =readl (ioaddr +DMA_BUS_MODE );
drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c +1 -1
@@ -18,7 +18,7 @@#include "dwmac100.h" #include "dwmac_dma.h" -static void dwmac100_dma_init (void __iomem *ioaddr, +static void dwmac100_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,int atds) {/* Enable Application Access by writing to DMA CSR0 */
drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c +1 -1
@@ -152,7 +152,7 @@ static void dwmac410_dma_init_channel(struct stmmac_priv *priv, ioaddr + DMA_CHAN_INTR_ENA(dwmac4_addrs, chan)); } -static void dwmac4_dma_init (void __iomem *ioaddr, +static void dwmac4_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,int atds) {u32 value =readl (ioaddr +DMA_SYS_BUS_MODE );
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +2 -1
@@ -152,7 +152,8 @@#define NUM_DWMAC1000_DMA_REGS 23#define NUM_DWMAC4_DMA_REGS 27 -void dwmac_enable_dma_transmission (void __iomem *ioaddr); +void dwmac_enable_dma_transmission (struct stmmac_priv *priv, +void __iomem *ioaddr,u32 chan);void dwmac_enable_dma_irq (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan,bool rx,bool tx); void dwmac_disable_dma_irq(struct stmmac_priv *priv, void __iomem *ioaddr,
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +2 -1
@@ -28,7 +28,8 @@ int dwmac_dma_reset(void __iomem *ioaddr) }/* CSR1 enables the transmit DMA to check for new descriptor */ -void dwmac_enable_dma_transmission (void __iomem *ioaddr) +void dwmac_enable_dma_transmission (struct stmmac_priv *priv, +void __iomem *ioaddr,u32 chan) {writel (1 , ioaddr +DMA_XMT_POLL_DEMAND ); }
drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c +1 -1
@@ -19,7 +19,7 @@ static int dwxgmac2_dma_reset(void __iomem *ioaddr) !(value & XGMAC_SWR), 0, 100000); } -static void dwxgmac2_dma_init (void __iomem *ioaddr, +static void dwxgmac2_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,int atds) {u32 value =readl (ioaddr +XGMAC_DMA_SYSBUS_MODE );
drivers/net/ethernet/stmicro/stmmac/hwif.h +6 -5
@@ -175,8 +175,8 @@ struct dma_features;struct stmmac_dma_ops {/* DMA core initialization */ int (*reset)(void __iomem *ioaddr); -void (*init)(void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg, -int atds); +void (*init)(struct stmmac_priv *priv,void __iomem *ioaddr, +struct stmmac_dma_cfg *dma_cfg,int atds);void (*init_chan)(struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,u32 chan); void (*init_rx_chan)(struct stmmac_priv *priv, void __iomem *ioaddr,
@@ -198,7 +198,8 @@ struct stmmac_dma_ops {/* To track extra statistic (if supported) */ void (*dma_diagnostic_fr)(struct stmmac_extra_stats *x,void __iomem *ioaddr); -void (*enable_dma_transmission) (void __iomem *ioaddr); +void (*enable_dma_transmission)(struct stmmac_priv *priv, +void __iomem *ioaddr,u32 chan);void (*enable_dma_irq)(struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan,bool rx,bool tx); void (*disable_dma_irq)(struct stmmac_priv *priv, void __iomem *ioaddr,
@@ -240,7 +241,7 @@ struct stmmac_dma_ops { }; #define stmmac_dma_init(__priv, __args...) \ - stmmac_do_void_callback(__priv, dma, init, __args) + stmmac_do_void_callback(__priv, dma, init, __priv, __args) #define stmmac_init_chan(__priv, __args...) \ stmmac_do_void_callback(__priv, dma, init_chan, __priv, __args) #define stmmac_init_rx_chan(__priv, __args...) \
@@ -258,7 +259,7 @@ struct stmmac_dma_ops { #define stmmac_dma_diagnostic_fr(__priv, __args...) \ stmmac_do_void_callback(__priv, dma, dma_diagnostic_fr, __args) #define stmmac_enable_dma_transmission(__priv, __args...) \ - stmmac_do_void_callback(__priv, dma, enable_dma_transmission, __args) + stmmac_do_void_callback(__priv, dma, enable_dma_transmission, __priv, __args) #define stmmac_enable_dma_irq(__priv, __args...) \ stmmac_do_void_callback(__priv, dma, enable_dma_irq, __priv, __args) #define stmmac_disable_dma_irq(__priv, __args...) \
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +3 -3
@@ -2558,7 +2558,7 @@ static bool stmmac_xdp_xmit_zc(struct stmmac_priv *priv, u32 queue, u32 budget) true, priv->mode, true, true, xdp_desc.len); -stmmac_enable_dma_transmission (priv, priv->ioaddr); +stmmac_enable_dma_transmission (priv, priv->ioaddr, queue);xsk_tx_metadata_to_compl (meta, &tx_q->tx_skbuff_dma[entry].xsk_meta);
@@ -4679,7 +4679,7 @@ static netdev_tx_t stmmac_xmit(struct sk_buff *skb, struct net_device *dev)netdev_tx_sent_queue (netdev_get_tx_queue (dev, queue), skb->len); -stmmac_enable_dma_transmission (priv, priv->ioaddr); +stmmac_enable_dma_transmission (priv, priv->ioaddr, queue);stmmac_flush_tx_descriptors (priv, queue);stmmac_tx_timer_arm (priv, queue);
@@ -4899,7 +4899,7 @@ static int stmmac_xdp_xmit_xdpf(struct stmmac_priv *priv, int queue,u64_stats_update_end_irqrestore (&txq_stats->syncp, flags); } -stmmac_enable_dma_transmission (priv, priv->ioaddr); +stmmac_enable_dma_transmission (priv, priv->ioaddr, queue); entry =STMMAC_GET_ENTRY (entry, priv->dma_conf.dma_tx_size); tx_q->cur_tx = entry;
Signature · 1 line
2.31.4
Simon Horman
reviewerRe: [PATCH net-next v7 1/9] net: stmmac: Pass stmmac_priv and chan in some callbacks
Quoted 24 lines · Yanteng Si
Loongson GMAC and GNET have some special features. To prepare for that, pass
stmmac_privand chan to more callbacks, and adjust the callbacks accordingly.Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h | 3 ++- drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c | 3 ++- drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/hwif.h | 11 ++++++----- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 6 +++--- 9 files changed, 18 insertions(+), 15 deletions(-)drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +0
-0
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c static void sun8i_dwmac_dma_start_tx(struct stmmac_priv *priv, · line 401
Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +1
-1@@ -395,7 +395,7 @@ static void sun8i_dwmac_dma_start_tx(struct stmmac_priv *priv,writel (v, ioaddr +EMAC_TX_CTL1 ); } -static void sun8i_dwmac_enable_dma_transmission (void __iomem *ioaddr) +static void sun8i_dwmac_enable_dma_transmission (void __iomem *ioaddr,u32 chan) {u32 v;
Hi Yanteng Si,
perhaps dwmac-sun8i.c needs to be further updated for this change?
.../dwmac-sun8i.c:568:10: error: incompatible function pointer types initializing 'void (*)(struct stmmac_priv *, void *, struct stmmac_dma_cfg *, int)' with an expression of type 'void (void *, struct stmmac_dma_cfg *, int)' [-Wincompatible-function-pointer-types]
568 | .init = sun8i_dwmac_dma_init,
| ^~~~~~~~~~~~~~~~~~~~ .../dwmac-sun8i.c:574:29: error: incompatible function pointer types initializing 'void (*)(struct stmmac_priv *, void *, u32)' (aka 'void (*)(struct stmmac_priv *, void *, unsigned int)') with an expression of type 'void (void *, u32)' (aka 'void (void *, unsigned int)') [-Wincompatible-function-pointer-types]
574 | .enable_dma_transmission = sun8i_dwmac_enable_dma_transmission,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2 errors generated.
Re: [PATCH net-next v7 1/9] net: stmmac: Pass stmmac_priv and chan in some callbacks
Quoted 37 lines · Simon Horman
Quoted 24 lines · Yanteng Si
Loongson GMAC and GNET have some special features. To prepare for that, pass
stmmac_privand chan to more callbacks, and adjust the callbacks accordingly.Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h | 3 ++- drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c | 3 ++- drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/hwif.h | 11 ++++++----- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 6 +++--- 9 files changed, 18 insertions(+), 15 deletions(-)drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +0
-0drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c static void sun8i_dwmac_dma_start_tx(struct stmmac_priv *priv, · line 401
Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +1
-1@@ -395,7 +395,7 @@ static void sun8i_dwmac_dma_start_tx(struct stmmac_priv *priv,writel (v, ioaddr +EMAC_TX_CTL1 ); } -static void sun8i_dwmac_enable_dma_transmission (void __iomem *ioaddr) +static void sun8i_dwmac_enable_dma_transmission (void __iomem *ioaddr,u32 chan) {u32 v;Hi Yanteng Si,
perhaps
dwmac-sun8i.cneeds to be further updated for this change?
Quoted 7 lines
.../dwmac-sun8i.c:568:10: error: incompatible function pointer types initializing 'void (*)(structstmmac_priv*, void *, structstmmac_dma_cfg*, int)' with an expression of type 'void (void *, structstmmac_dma_cfg*, int)' [-Wincompatible-function-pointer-types]568 | .init = sun8i_dwmac_dma_init, | ^~~~~~~~~~~~~~~~~~~~
.../dwmac-sun8i.c:574:29: error: incompatible function pointer types initializing 'void (*)(structstmmac_priv*, void *, u32)' (aka 'void (*)(structstmmac_priv*, void *, unsigned int)') with an expression of type 'void (void *, u32)' (aka 'void (void *, unsigned int)') [-Wincompatible-function-pointer-types]
574 | .enable_dma_transmission =sun8i_dwmac_enable_dma_transmission,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2 errors generated.
Sorry, I'll fix it.
Thanks,
Yanteng
Re: [PATCH net-next v7 1/9] net: stmmac: Pass stmmac_priv and chan in some callbacks
In reply to Yanteng SiHi Yanteng
Quoted 24 lines · Yanteng Si
Loongson GMAC and GNET have some special features. To prepare for that, pass
stmmac_privand chan to more callbacks, and adjust the callbacks accordingly.Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h | 3 ++- drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c | 3 ++- drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/hwif.h | 11 ++++++----- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 6 +++--- 9 files changed, 18 insertions(+), 15 deletions(-)drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +0
-0
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c static void sun8i_dwmac_dma_start_tx(struct stmmac_priv *priv, · line 399
Quoted 6 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +1
-1@@ -395,7 +395,7 @@ static void sun8i_dwmac_dma_start_tx(struct stmmac_priv *priv,writel (v, ioaddr +EMAC_TX_CTL1 ); } -static void sun8i_dwmac_enable_dma_transmission (void __iomem *ioaddr) +static void sun8i_dwmac_enable_dma_transmission (void __iomem *ioaddr,u32 chan)
As Simon correctly noted this prototype is incomplete. Although AFAICS you never use a pointer to stmmac_priv in this method. So I guess you could fix the callback prototype instead.
Quoted 88 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +0
-0{u32 v;drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +1
-1@@ -70,7 +70,7 @@ static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi)writel (value, ioaddr +DMA_AXI_BUS_MODE ); } -static void dwmac1000_dma_init (void __iomem *ioaddr, +static void dwmac1000_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,int atds) {u32 value =readl (ioaddr +DMA_BUS_MODE );drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c +1
-1@@ -18,7 +18,7 @@#include "dwmac100.h" #include "dwmac_dma.h" -static void dwmac100_dma_init (void __iomem *ioaddr, +static void dwmac100_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,int atds) {/* Enable Application Access by writing to DMA CSR0 */ drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c +1
-1@@ -152,7 +152,7 @@ static void dwmac410_dma_init_channel(struct stmmac_priv *priv, ioaddr + DMA_CHAN_INTR_ENA(dwmac4_addrs, chan)); } -static void dwmac4_dma_init (void __iomem *ioaddr, +static void dwmac4_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,int atds) {u32 value =readl (ioaddr +DMA_SYS_BUS_MODE );drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +2
-1@@ -152,7 +152,8 @@#define NUM_DWMAC1000_DMA_REGS 23#define NUM_DWMAC4_DMA_REGS 27 -void dwmac_enable_dma_transmission (void __iomem *ioaddr); +void dwmac_enable_dma_transmission (struct stmmac_priv *priv, +void __iomem *ioaddr,u32 chan);void dwmac_enable_dma_irq (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan,bool rx,bool tx); void dwmac_disable_dma_irq(struct stmmac_priv *priv, void __iomem *ioaddr,drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +2
-1@@ -28,7 +28,8 @@ int dwmac_dma_reset(void __iomem *ioaddr) }/* CSR1 enables the transmit DMA to check for new descriptor */ -void dwmac_enable_dma_transmission (void __iomem *ioaddr) +void dwmac_enable_dma_transmission (struct stmmac_priv *priv, +void __iomem *ioaddr,u32 chan) {writel (1 , ioaddr +DMA_XMT_POLL_DEMAND ); }drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c +1
-1@@ -19,7 +19,7 @@ static int dwxgmac2_dma_reset(void __iomem *ioaddr) !(value & XGMAC_SWR), 0, 100000); } -static void dwxgmac2_dma_init (void __iomem *ioaddr, +static void dwxgmac2_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,int atds) {u32 value =readl (ioaddr +XGMAC_DMA_SYSBUS_MODE );drivers/net/ethernet/stmicro/stmmac/hwif.h +0
-0
drivers/net/ethernet/stmicro/stmmac/hwif.h struct dma_features; · line 180
Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/hwif.h +2
-2@@ -175,8 +175,8 @@ struct dma_features;struct stmmac_dma_ops {/* DMA core initialization */ int (*reset)(void __iomem *ioaddr); -void (*init)(void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg, -int atds); +void (*init)(struct stmmac_priv *priv,void __iomem *ioaddr, +struct stmmac_dma_cfg *dma_cfg,int atds);
There is a good chance this change is also unnecessary. I'll post my comment about that to Patch 4/9.
drivers/net/ethernet/stmicro/stmmac/hwif.h struct stmmac_dma_ops { · line 204
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/hwif.h +0
-0void (*init_chan)(struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,u32 chan);drivers/net/ethernet/stmicro/stmmac/hwif.h +2
-1void (*init_rx_chan)(struct stmmac_priv *priv, void __iomem *ioaddr,@@ -198,7 +198,8 @@ struct stmmac_dma_ops {/* To track extra statistic (if supported) */ void (*dma_diagnostic_fr)(struct stmmac_extra_stats *x,void __iomem *ioaddr); -void (*enable_dma_transmission) (void __iomem *ioaddr); +void (*enable_dma_transmission)(struct stmmac_priv *priv, +void __iomem *ioaddr,u32 chan);
Why do you need the pointer to the stmmac_priv structure instance here? I failed to find a place you using it in the subsequent patches.
* Sigh, just a general note in case if somebody would wish to make
* things a bit more optimised and less complicated. The purpose of the
* enable_dma_transmission() callback is to re-activate the DMA-engine
* - exit from suspension and start poll-demanding the DMA descriptors.
* In QoS GMAC and XGMAC the same is done by updating the Tx tail
* pointer. It's implemented in stmmac_set_tx_tail_ptr(). So basically
* both stmmac_enable_dma_transmission() and stmmac_set_tx_tail_ptr()
* should be almost always called side-by-side. Alas the current
* generic driver part doesn't do that. If it did in a some common way
* you wouldn't have needed the enable_dma_transmission() update
* because it would have already been updated to accept the
* channel/queue parameter.
-Serge(y)
Quoted 55 lines
drivers/net/ethernet/stmicro/stmmac/hwif.h +0
-0void (*enable_dma_irq)(struct stmmac_priv *priv, void __iomem *ioaddr,drivers/net/ethernet/stmicro/stmmac/hwif.h +2
-2u32 chan, bool rx, bool tx); void (*disable_dma_irq)(struct stmmac_priv *priv, void __iomem *ioaddr,@@ -240,7 +241,7 @@ struct stmmac_dma_ops { }; #define stmmac_dma_init(__priv, __args...) \ - stmmac_do_void_callback(__priv, dma, init, __args) + stmmac_do_void_callback(__priv, dma, init, __priv, __args) #define stmmac_init_chan(__priv, __args...) \ stmmac_do_void_callback(__priv, dma, init_chan, __priv, __args) #define stmmac_init_rx_chan(__priv, __args...) \@@ -258,7 +259,7 @@ struct stmmac_dma_ops { #define stmmac_dma_diagnostic_fr(__priv, __args...) \ stmmac_do_void_callback(__priv, dma, dma_diagnostic_fr, __args) #define stmmac_enable_dma_transmission(__priv, __args...) \ - stmmac_do_void_callback(__priv, dma, enable_dma_transmission, __args) + stmmac_do_void_callback(__priv, dma, enable_dma_transmission, __priv, __args) #define stmmac_enable_dma_irq(__priv, __args...) \ stmmac_do_void_callback(__priv, dma, enable_dma_irq, __priv, __args) #define stmmac_disable_dma_irq(__priv, __args...) \drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +3
-3@@ -2558,7 +2558,7 @@ static bool stmmac_xdp_xmit_zc(struct stmmac_priv *priv, u32 queue, u32 budget) true, priv->mode, true, true, xdp_desc.len); -stmmac_enable_dma_transmission (priv, priv->ioaddr); +stmmac_enable_dma_transmission (priv, priv->ioaddr, queue);xsk_tx_metadata_to_compl (meta, &tx_q->tx_skbuff_dma[entry].xsk_meta);@@ -4679,7 +4679,7 @@ static netdev_tx_t stmmac_xmit(struct sk_buff *skb, struct net_device *dev)netdev_tx_sent_queue (netdev_get_tx_queue (dev, queue), skb->len); -stmmac_enable_dma_transmission (priv, priv->ioaddr); +stmmac_enable_dma_transmission (priv, priv->ioaddr, queue);stmmac_flush_tx_descriptors (priv, queue);stmmac_tx_timer_arm (priv, queue);@@ -4899,7 +4899,7 @@ static int stmmac_xdp_xmit_xdpf(struct stmmac_priv *priv, int queue,u64_stats_update_end_irqrestore (&txq_stats->syncp, flags); } -stmmac_enable_dma_transmission (priv, priv->ioaddr); +stmmac_enable_dma_transmission (priv, priv->ioaddr, queue); entry =STMMAC_GET_ENTRY (entry, priv->dma_conf.dma_tx_size); tx_q->cur_tx = entry;Signature · 1 line
2.31.4
Re: [PATCH net-next v7 1/9] net: stmmac: Pass stmmac_priv and chan in some callbacks
Quoted 142 lines · Serge Semin
Hi Yanteng
Quoted 24 lines · Yanteng Si
Loongson GMAC and GNET have some special features. To prepare for that, pass
stmmac_privand chan to more callbacks, and adjust the callbacks accordingly.Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h | 3 ++- drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c | 3 ++- drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/hwif.h | 11 ++++++----- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 6 +++--- 9 files changed, 18 insertions(+), 15 deletions(-)drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +0
-0drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c static void sun8i_dwmac_dma_start_tx(struct stmmac_priv *priv, · line 398
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +1
-1@@ -395,7 +395,7 @@ static void sun8i_dwmac_dma_start_tx(struct stmmac_priv *priv,writel (v, ioaddr +EMAC_TX_CTL1 ); } -static void sun8i_dwmac_enable_dma_transmission (void __iomem *ioaddr) +static void sun8i_dwmac_enable_dma_transmission (void __iomem *ioaddr,u32 chan)As Simon correctly noted this prototype is incomplete. Although AFAICS you never use a pointer to
stmmac_privin this method. So I guess you could fix the callback prototype instead.Quoted 88 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +0
-0{u32 v;drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +1
-1@@ -70,7 +70,7 @@ static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi)writel (value, ioaddr +DMA_AXI_BUS_MODE ); } -static void dwmac1000_dma_init (void __iomem *ioaddr, +static void dwmac1000_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,int atds) {u32 value =readl (ioaddr +DMA_BUS_MODE );drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c +1
-1@@ -18,7 +18,7 @@#include "dwmac100.h" #include "dwmac_dma.h" -static void dwmac100_dma_init (void __iomem *ioaddr, +static void dwmac100_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,int atds) {/* Enable Application Access by writing to DMA CSR0 */ drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c +1
-1@@ -152,7 +152,7 @@ static void dwmac410_dma_init_channel(struct stmmac_priv *priv, ioaddr + DMA_CHAN_INTR_ENA(dwmac4_addrs, chan)); } -static void dwmac4_dma_init (void __iomem *ioaddr, +static void dwmac4_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,int atds) {u32 value =readl (ioaddr +DMA_SYS_BUS_MODE );drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +2
-1@@ -152,7 +152,8 @@#define NUM_DWMAC1000_DMA_REGS 23#define NUM_DWMAC4_DMA_REGS 27 -void dwmac_enable_dma_transmission (void __iomem *ioaddr); +void dwmac_enable_dma_transmission (struct stmmac_priv *priv, +void __iomem *ioaddr,u32 chan);void dwmac_enable_dma_irq (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan,bool rx,bool tx); void dwmac_disable_dma_irq(struct stmmac_priv *priv, void __iomem *ioaddr,drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +2
-1@@ -28,7 +28,8 @@ int dwmac_dma_reset(void __iomem *ioaddr) }/* CSR1 enables the transmit DMA to check for new descriptor */ -void dwmac_enable_dma_transmission (void __iomem *ioaddr) +void dwmac_enable_dma_transmission (struct stmmac_priv *priv, +void __iomem *ioaddr,u32 chan) {writel (1 , ioaddr +DMA_XMT_POLL_DEMAND ); }drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c +1
-1@@ -19,7 +19,7 @@ static int dwxgmac2_dma_reset(void __iomem *ioaddr) !(value & XGMAC_SWR), 0, 100000); } -static void dwxgmac2_dma_init (void __iomem *ioaddr, +static void dwxgmac2_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,int atds) {u32 value =readl (ioaddr +XGMAC_DMA_SYSBUS_MODE );drivers/net/ethernet/stmicro/stmmac/hwif.h +0
-0drivers/net/ethernet/stmicro/stmmac/hwif.h struct dma_features; · line 179
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/hwif.h +2
-2@@ -175,8 +175,8 @@ struct dma_features;struct stmmac_dma_ops {/* DMA core initialization */ int (*reset)(void __iomem *ioaddr); -void (*init)(void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg, -int atds); +void (*init)(struct stmmac_priv *priv,void __iomem *ioaddr, +struct stmmac_dma_cfg *dma_cfg,int atds);There is a good chance this change is also unnecessary. I'll post my comment about that to Patch 4/9.
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/hwif.h +0
-0void (*init_chan)(struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,u32 chan); void (*init_rx_chan)(struct stmmac_priv *priv, void __iomem *ioaddr,@@ -198,7 +198,8 @@ struct stmmac_dma_ops {/* To track extra statistic (if supported) */ void (*dma_diagnostic_fr)(struct stmmac_extra_stats *x,void __iomem *ioaddr);
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/hwif.h struct stmmac_dma_ops { · line 202
Quoted 3 lines
drivers/net/ethernet/stmicro/stmmac/hwif.h +2
-1-void (*enable_dma_transmission) (void __iomem *ioaddr); +void (*enable_dma_transmission)(struct stmmac_priv *priv, +void __iomem *ioaddr,u32 chan);Why do you need the pointer to the
stmmac_privstructure instance here? I failed to find a place you using it in the subsequent patches.
it's here:
@@ -70,7 +70,7 @@ static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi) writel(value, ioaddr + DMA_AXI_BUS_MODE);
}
-static void dwmac1000_dma_init(void __iomem *ioaddr,
+static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr, struct stmmac_dma_cfg *dma_cfg, int atds)
{
u32 value = readl(ioaddr + DMA_BUS_MODE);
@@ -118,7 +118,10 @@ static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr,
u32 dma_intr_mask;
/* Mask interrupts by writing to CSR7 */
- dma_intr_mask = DMA_INTR_DEFAULT_MASK;
+ if (priv->plat->flags & STMMAC_FLAG_HAS_LGMAC) + dma_intr_mask = DMA_INTR_DEFAULT_MASK_LOONGSON; + else
+ dma_intr_mask = DMA_INTR_DEFAULT_MASK;
dma_config(ioaddr + DMA_BUS_MODE, ioaddr + DMA_INTR_ENA,
dma_cfg, dma_intr_mask, atds);
Thank you for all your comments, I need some time to understand. :)
Thanks,
Yanteng
Quoted 71 lines
* Sigh, just a general note in case if somebody would wish to make
* things a bit more optimised and less complicated. The purpose of the
*enable_dma_transmission()callback is to re-activate the DMA-engine
* - exit from suspension and start poll-demanding the DMA descriptors.
* In QoS GMAC and XGMAC the same is done by updating the Tx tail
* pointer. It's implemented instmmac_set_tx_tail_ptr(). So basically
* bothstmmac_enable_dma_transmission()andstmmac_set_tx_tail_ptr()
* should be almost always called side-by-side. Alas the current
* generic driver part doesn't do that. If it did in a some common way
* you wouldn't have needed theenable_dma_transmission()update
* because it would have already been updated to accept the
* channel/queue parameter.-Serge(y)
Quoted 55 lines
drivers/net/ethernet/stmicro/stmmac/hwif.h +2
-2void (*enable_dma_irq)(struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan,bool rx,bool tx); void (*disable_dma_irq)(struct stmmac_priv *priv, void __iomem *ioaddr,@@ -240,7 +241,7 @@ struct stmmac_dma_ops { }; #define stmmac_dma_init(__priv, __args...) \ - stmmac_do_void_callback(__priv, dma, init, __args) + stmmac_do_void_callback(__priv, dma, init, __priv, __args) #define stmmac_init_chan(__priv, __args...) \ stmmac_do_void_callback(__priv, dma, init_chan, __priv, __args) #define stmmac_init_rx_chan(__priv, __args...) \@@ -258,7 +259,7 @@ struct stmmac_dma_ops { #define stmmac_dma_diagnostic_fr(__priv, __args...) \ stmmac_do_void_callback(__priv, dma, dma_diagnostic_fr, __args) #define stmmac_enable_dma_transmission(__priv, __args...) \ - stmmac_do_void_callback(__priv, dma, enable_dma_transmission, __args) + stmmac_do_void_callback(__priv, dma, enable_dma_transmission, __priv, __args) #define stmmac_enable_dma_irq(__priv, __args...) \ stmmac_do_void_callback(__priv, dma, enable_dma_irq, __priv, __args) #define stmmac_disable_dma_irq(__priv, __args...) \drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +3
-3@@ -2558,7 +2558,7 @@ static bool stmmac_xdp_xmit_zc(struct stmmac_priv *priv, u32 queue, u32 budget) true, priv->mode, true, true, xdp_desc.len); -stmmac_enable_dma_transmission (priv, priv->ioaddr); +stmmac_enable_dma_transmission (priv, priv->ioaddr, queue);xsk_tx_metadata_to_compl (meta, &tx_q->tx_skbuff_dma[entry].xsk_meta);@@ -4679,7 +4679,7 @@ static netdev_tx_t stmmac_xmit(struct sk_buff *skb, struct net_device *dev)netdev_tx_sent_queue (netdev_get_tx_queue (dev, queue), skb->len); -stmmac_enable_dma_transmission (priv, priv->ioaddr); +stmmac_enable_dma_transmission (priv, priv->ioaddr, queue);stmmac_flush_tx_descriptors (priv, queue);stmmac_tx_timer_arm (priv, queue);@@ -4899,7 +4899,7 @@ static int stmmac_xdp_xmit_xdpf(struct stmmac_priv *priv, int queue,u64_stats_update_end_irqrestore (&txq_stats->syncp, flags); } -stmmac_enable_dma_transmission (priv, priv->ioaddr); +stmmac_enable_dma_transmission (priv, priv->ioaddr, queue); entry =STMMAC_GET_ENTRY (entry, priv->dma_conf.dma_tx_size); tx_q->cur_tx = entry;Signature · 1 line
2.31.4
Re: [PATCH net-next v7 1/9] net: stmmac: Pass stmmac_priv and chan in some callbacks
Quoted 144 lines · Yanteng Si
Quoted 134 lines · Serge Semin
Hi Yanteng
Quoted 24 lines · Yanteng Si
Loongson GMAC and GNET have some special features. To prepare for that, pass
stmmac_privand chan to more callbacks, and adjust the callbacks accordingly.Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h | 3 ++- drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c | 3 ++- drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/hwif.h | 11 ++++++----- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 6 +++--- 9 files changed, 18 insertions(+), 15 deletions(-)drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +0
-0drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c static void sun8i_dwmac_dma_start_tx(struct stmmac_priv *priv, · line 397
Quoted 4 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +1
-1@@ -395,7 +395,7 @@ static void sun8i_dwmac_dma_start_tx(struct stmmac_priv *priv,writel (v, ioaddr +EMAC_TX_CTL1 ); } -static void sun8i_dwmac_enable_dma_transmission (void __iomem *ioaddr) +static void sun8i_dwmac_enable_dma_transmission (void __iomem *ioaddr,u32 chan)As Simon correctly noted this prototype is incomplete. Although AFAICS you never use a pointer to
stmmac_privin this method. So I guess you could fix the callback prototype instead.Quoted 81 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +0
-0{u32 v;drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +1
-1@@ -70,7 +70,7 @@ static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi)writel (value, ioaddr +DMA_AXI_BUS_MODE ); } -static void dwmac1000_dma_init (void __iomem *ioaddr, +static void dwmac1000_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,int atds) {u32 value =readl (ioaddr +DMA_BUS_MODE );drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c +1
-1@@ -18,7 +18,7 @@#include "dwmac100.h" #include "dwmac_dma.h" -static void dwmac100_dma_init (void __iomem *ioaddr, +static void dwmac100_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,int atds) {/* Enable Application Access by writing to DMA CSR0 */ drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c +1
-1@@ -152,7 +152,7 @@ static void dwmac410_dma_init_channel(struct stmmac_priv *priv, ioaddr + DMA_CHAN_INTR_ENA(dwmac4_addrs, chan)); } -static void dwmac4_dma_init (void __iomem *ioaddr, +static void dwmac4_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,int atds) {u32 value =readl (ioaddr +DMA_SYS_BUS_MODE );drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +2
-1@@ -152,7 +152,8 @@#define NUM_DWMAC1000_DMA_REGS 23#define NUM_DWMAC4_DMA_REGS 27 -void dwmac_enable_dma_transmission (void __iomem *ioaddr); +void dwmac_enable_dma_transmission (struct stmmac_priv *priv, +void __iomem *ioaddr,u32 chan);void dwmac_enable_dma_irq (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan,bool rx,bool tx); void dwmac_disable_dma_irq(struct stmmac_priv *priv, void __iomem *ioaddr,drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +2
-1@@ -28,7 +28,8 @@ int dwmac_dma_reset(void __iomem *ioaddr) }/* CSR1 enables the transmit DMA to check for new descriptor */ -void dwmac_enable_dma_transmission (void __iomem *ioaddr) +void dwmac_enable_dma_transmission (struct stmmac_priv *priv, +void __iomem *ioaddr,u32 chan) {writel (1 , ioaddr +DMA_XMT_POLL_DEMAND ); }drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c +1
-1@@ -19,7 +19,7 @@ static int dwxgmac2_dma_reset(void __iomem *ioaddr) !(value & XGMAC_SWR), 0, 100000); } -static void dwxgmac2_dma_init (void __iomem *ioaddr, +static void dwxgmac2_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,int atds) {u32 value =readl (ioaddr +XGMAC_DMA_SYSBUS_MODE );drivers/net/ethernet/stmicro/stmmac/hwif.h +0
-0drivers/net/ethernet/stmicro/stmmac/hwif.h struct dma_features; · line 179
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/hwif.h +2
-2@@ -175,8 +175,8 @@ struct dma_features;struct stmmac_dma_ops {/* DMA core initialization */ int (*reset)(void __iomem *ioaddr); -void (*init)(void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg, -int atds); +void (*init)(struct stmmac_priv *priv,void __iomem *ioaddr, +struct stmmac_dma_cfg *dma_cfg,int atds);There is a good chance this change is also unnecessary. I'll post my comment about that to Patch 4/9.
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/hwif.h +0
-0void (*init_chan)(struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,u32 chan); void (*init_rx_chan)(struct stmmac_priv *priv, void __iomem *ioaddr,@@ -198,7 +198,8 @@ struct stmmac_dma_ops {/* To track extra statistic (if supported) */ void (*dma_diagnostic_fr)(struct stmmac_extra_stats *x,void __iomem *ioaddr);Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/hwif.h struct stmmac_dma_ops { · line 202
Quoted 3 lines
drivers/net/ethernet/stmicro/stmmac/hwif.h +2
-1-void (*enable_dma_transmission) (void __iomem *ioaddr); +void (*enable_dma_transmission)(struct stmmac_priv *priv, +void __iomem *ioaddr,u32 chan);Why do you need the pointer to the
stmmac_privstructure instance here? I failed to find a place you using it in the subsequent patches.it's here:
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_axi(void __iomem *ioaddr, struct · line 76
Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +1
-1@@ -70,7 +70,7 @@ static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi) writel(value, ioaddr + DMA_AXI_BUS_MODE); } -static void dwmac1000_dma_init(void __iomem *ioaddr, +static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem
Em, my comment was about enable_dma_transmission() ! I don't see you using the stmmac_priv pointer in any updates for that method.
Quoted 19 lines
*ioaddr,
structstmmac_dma_cfg*dma_cfg, int atds) {
u32 value =readl(ioaddr + DMA_BUS_MODE);(quoted diff) +4
-1@@ -118,7 +118,10 @@ static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr, u32 dma_intr_mask; /* Mask interrupts by writing to CSR7 */ - dma_intr_mask = DMA_INTR_DEFAULT_MASK; + if (priv->plat->flags & STMMAC_FLAG_HAS_LGMAC) + dma_intr_mask = DMA_INTR_DEFAULT_MASK_LOONGSON; + else + dma_intr_mask = DMA_INTR_DEFAULT_MASK;dma_config(ioaddr +
DMA_BUS_MODE, ioaddr +DMA_INTR_ENA,
Quoted 5 lines
dma_cfg,dma_intr_mask, atds);Thank you for all your comments, I need some time to understand. :)
Don't hesitate to ask should any question arise in my comments regard.
-Serge(y)
Quoted 70 lines
Thanks,
Yanteng
Quoted 63 lines
* Sigh, just a general note in case if somebody would wish to make
* things a bit more optimised and less complicated. The purpose of the
*enable_dma_transmission()callback is to re-activate the DMA-engine
* - exit from suspension and start poll-demanding the DMA descriptors.
* In QoS GMAC and XGMAC the same is done by updating the Tx tail
* pointer. It's implemented instmmac_set_tx_tail_ptr(). So basically
* bothstmmac_enable_dma_transmission()andstmmac_set_tx_tail_ptr()
* should be almost always called side-by-side. Alas the current
* generic driver part doesn't do that. If it did in a some common way
* you wouldn't have needed theenable_dma_transmission()update
* because it would have already been updated to accept the
* channel/queue parameter.-Serge(y)
Quoted 47 lines
drivers/net/ethernet/stmicro/stmmac/hwif.h +2
-2void (*enable_dma_irq)(struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan,bool rx,bool tx); void (*disable_dma_irq)(struct stmmac_priv *priv, void __iomem *ioaddr,@@ -240,7 +241,7 @@ struct stmmac_dma_ops { }; #define stmmac_dma_init(__priv, __args...) \ - stmmac_do_void_callback(__priv, dma, init, __args) + stmmac_do_void_callback(__priv, dma, init, __priv, __args) #define stmmac_init_chan(__priv, __args...) \ stmmac_do_void_callback(__priv, dma, init_chan, __priv, __args) #define stmmac_init_rx_chan(__priv, __args...) \@@ -258,7 +259,7 @@ struct stmmac_dma_ops { #define stmmac_dma_diagnostic_fr(__priv, __args...) \ stmmac_do_void_callback(__priv, dma, dma_diagnostic_fr, __args) #define stmmac_enable_dma_transmission(__priv, __args...) \ - stmmac_do_void_callback(__priv, dma, enable_dma_transmission, __args) + stmmac_do_void_callback(__priv, dma, enable_dma_transmission, __priv, __args) #define stmmac_enable_dma_irq(__priv, __args...) \ stmmac_do_void_callback(__priv, dma, enable_dma_irq, __priv, __args) #define stmmac_disable_dma_irq(__priv, __args...) \drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +3
-3@@ -2558,7 +2558,7 @@ static bool stmmac_xdp_xmit_zc(struct stmmac_priv *priv, u32 queue, u32 budget) true, priv->mode, true, true, xdp_desc.len); -stmmac_enable_dma_transmission (priv, priv->ioaddr); +stmmac_enable_dma_transmission (priv, priv->ioaddr, queue);xsk_tx_metadata_to_compl (meta, &tx_q->tx_skbuff_dma[entry].xsk_meta);@@ -4679,7 +4679,7 @@ static netdev_tx_t stmmac_xmit(struct sk_buff *skb, struct net_device *dev)netdev_tx_sent_queue (netdev_get_tx_queue (dev, queue), skb->len); -stmmac_enable_dma_transmission (priv, priv->ioaddr); +stmmac_enable_dma_transmission (priv, priv->ioaddr, queue);stmmac_flush_tx_descriptors (priv, queue);stmmac_tx_timer_arm (priv, queue);@@ -4899,7 +4899,7 @@ static int stmmac_xdp_xmit_xdpf(struct stmmac_priv *priv, int queue,u64_stats_update_end_irqrestore (&txq_stats->syncp, flags); } -stmmac_enable_dma_transmission (priv, priv->ioaddr); +stmmac_enable_dma_transmission (priv, priv->ioaddr, queue); entry =STMMAC_GET_ENTRY (entry, priv->dma_conf.dma_tx_size); tx_q->cur_tx = entry;Signature · 1 line
2.31.4
Re: [PATCH net-next v7 1/9] net: stmmac: Pass stmmac_priv and chan in some callbacks
Quoted 148 lines · Serge Semin
Quoted 146 lines · Yanteng Si
Quoted 126 lines · Serge Semin
Hi Yanteng
Quoted 24 lines · Yanteng Si
Loongson GMAC and GNET have some special features. To prepare for that, pass
stmmac_privand chan to more callbacks, and adjust the callbacks accordingly.Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h | 3 ++- drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c | 3 ++- drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c | 2 +- drivers/net/ethernet/stmicro/stmmac/hwif.h | 11 ++++++----- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 6 +++--- 9 files changed, 18 insertions(+), 15 deletions(-)drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +0
-0drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c static void sun8i_dwmac_dma_start_tx(struct stmmac_priv *priv, · line 397
Quoted 4 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +1
-1@@ -395,7 +395,7 @@ static void sun8i_dwmac_dma_start_tx(struct stmmac_priv *priv,writel (v, ioaddr +EMAC_TX_CTL1 ); } -static void sun8i_dwmac_enable_dma_transmission (void __iomem *ioaddr) +static void sun8i_dwmac_enable_dma_transmission (void __iomem *ioaddr,u32 chan)As Simon correctly noted this prototype is incomplete. Although AFAICS you never use a pointer to
stmmac_privin this method. So I guess you could fix the callback prototype instead.Quoted 81 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +0
-0{u32 v;drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +1
-1@@ -70,7 +70,7 @@ static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi)writel (value, ioaddr +DMA_AXI_BUS_MODE ); } -static void dwmac1000_dma_init (void __iomem *ioaddr, +static void dwmac1000_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,int atds) {u32 value =readl (ioaddr +DMA_BUS_MODE );drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c +1
-1@@ -18,7 +18,7 @@#include "dwmac100.h" #include "dwmac_dma.h" -static void dwmac100_dma_init (void __iomem *ioaddr, +static void dwmac100_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,int atds) {/* Enable Application Access by writing to DMA CSR0 */ drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c +1
-1@@ -152,7 +152,7 @@ static void dwmac410_dma_init_channel(struct stmmac_priv *priv, ioaddr + DMA_CHAN_INTR_ENA(dwmac4_addrs, chan)); } -static void dwmac4_dma_init (void __iomem *ioaddr, +static void dwmac4_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,int atds) {u32 value =readl (ioaddr +DMA_SYS_BUS_MODE );drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +2
-1@@ -152,7 +152,8 @@#define NUM_DWMAC1000_DMA_REGS 23#define NUM_DWMAC4_DMA_REGS 27 -void dwmac_enable_dma_transmission (void __iomem *ioaddr); +void dwmac_enable_dma_transmission (struct stmmac_priv *priv, +void __iomem *ioaddr,u32 chan);void dwmac_enable_dma_irq (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan,bool rx,bool tx); void dwmac_disable_dma_irq(struct stmmac_priv *priv, void __iomem *ioaddr,drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +2
-1@@ -28,7 +28,8 @@ int dwmac_dma_reset(void __iomem *ioaddr) }/* CSR1 enables the transmit DMA to check for new descriptor */ -void dwmac_enable_dma_transmission (void __iomem *ioaddr) +void dwmac_enable_dma_transmission (struct stmmac_priv *priv, +void __iomem *ioaddr,u32 chan) {writel (1 , ioaddr +DMA_XMT_POLL_DEMAND ); }drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c +1
-1@@ -19,7 +19,7 @@ static int dwxgmac2_dma_reset(void __iomem *ioaddr) !(value & XGMAC_SWR), 0, 100000); } -static void dwxgmac2_dma_init (void __iomem *ioaddr, +static void dwxgmac2_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,int atds) {u32 value =readl (ioaddr +XGMAC_DMA_SYSBUS_MODE );drivers/net/ethernet/stmicro/stmmac/hwif.h +0
-0drivers/net/ethernet/stmicro/stmmac/hwif.h struct dma_features; · line 179
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/hwif.h +2
-2@@ -175,8 +175,8 @@ struct dma_features;struct stmmac_dma_ops {/* DMA core initialization */ int (*reset)(void __iomem *ioaddr); -void (*init)(void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg, -int atds); +void (*init)(struct stmmac_priv *priv,void __iomem *ioaddr, +struct stmmac_dma_cfg *dma_cfg,int atds);There is a good chance this change is also unnecessary. I'll post my comment about that to Patch 4/9.
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/hwif.h struct stmmac_dma_ops { · line 202
Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/hwif.h +2
-1void (*init_chan)(struct stmmac_priv *priv,void __iomem *ioaddr,struct stmmac_dma_cfg *dma_cfg,u32 chan); void (*init_rx_chan)(struct stmmac_priv *priv, void __iomem *ioaddr,@@ -198,7 +198,8 @@ struct stmmac_dma_ops {/* To track extra statistic (if supported) */ void (*dma_diagnostic_fr)(struct stmmac_extra_stats *x,void __iomem *ioaddr); -void (*enable_dma_transmission) (void __iomem *ioaddr); +void (*enable_dma_transmission)(struct stmmac_priv *priv, +void __iomem *ioaddr,u32 chan);Why do you need the pointer to the
stmmac_privstructure instance here? I failed to find a place you using it in the subsequent patches.it's here:
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +0
-0@@ -70,7 +70,7 @@ static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi) writel(value, ioaddr + DMA_AXI_BUS_MODE); }
Quoted 4 lines
Review static void dwmac1000_dma_axi(void __iomem *ioaddr, struct · line 74
Quoted 2 lines
(quoted diff) +1
-1-static void dwmac1000_dma_init(void __iomem *ioaddr, +static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomemEm, my comment was about
enable_dma_transmission()! I don't see you using thestmmac_privpointer in any updates for that method.
Oh! I see.
you're right, it will be removed.
Quoted 18 lines
Quoted 18 lines
(quoted diff) +0
-0*ioaddr, struct stmmac_dma_cfg *dma_cfg, int atds){
u32 value =readl(ioaddr + DMA_BUS_MODE);(quoted diff) +4
-1@@ -118,7 +118,10 @@ static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr, u32 dma_intr_mask; /* Mask interrupts by writing to CSR7 */ - dma_intr_mask = DMA_INTR_DEFAULT_MASK; + if (priv->plat->flags & STMMAC_FLAG_HAS_LGMAC) + dma_intr_mask = DMA_INTR_DEFAULT_MASK_LOONGSON; + else + dma_intr_mask = DMA_INTR_DEFAULT_MASK;
Quoted 7 lines
Quoted 6 lines
dma_config(ioaddr +
DMA_BUS_MODE, ioaddr +DMA_INTR_ENA,
dma_cfg,dma_intr_mask, atds);Thank you for all your comments, I need some time to understand. :)
Don't hesitate to ask should any question arise in my comments regard.
Ok, I will.
Thanks,
Yanteng
Quoted 70 lines
-Serge(y)
Quoted 67 lines
Thanks,
Yanteng
Quoted 62 lines
* Sigh, just a general note in case if somebody would wish to make
* things a bit more optimised and less complicated. The purpose of the
*enable_dma_transmission()callback is to re-activate the DMA-engine
* - exit from suspension and start poll-demanding the DMA descriptors.
* In QoS GMAC and XGMAC the same is done by updating the Tx tail
* pointer. It's implemented instmmac_set_tx_tail_ptr(). So basically
* bothstmmac_enable_dma_transmission()andstmmac_set_tx_tail_ptr()
* should be almost always called side-by-side. Alas the current
* generic driver part doesn't do that. If it did in a some common way
* you wouldn't have needed theenable_dma_transmission()update
* because it would have already been updated to accept the
* channel/queue parameter.-Serge(y)
Quoted 47 lines
drivers/net/ethernet/stmicro/stmmac/hwif.h +2
-2void (*enable_dma_irq)(struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan,bool rx,bool tx); void (*disable_dma_irq)(struct stmmac_priv *priv, void __iomem *ioaddr,@@ -240,7 +241,7 @@ struct stmmac_dma_ops { }; #define stmmac_dma_init(__priv, __args...) \ - stmmac_do_void_callback(__priv, dma, init, __args) + stmmac_do_void_callback(__priv, dma, init, __priv, __args) #define stmmac_init_chan(__priv, __args...) \ stmmac_do_void_callback(__priv, dma, init_chan, __priv, __args) #define stmmac_init_rx_chan(__priv, __args...) \@@ -258,7 +259,7 @@ struct stmmac_dma_ops { #define stmmac_dma_diagnostic_fr(__priv, __args...) \ stmmac_do_void_callback(__priv, dma, dma_diagnostic_fr, __args) #define stmmac_enable_dma_transmission(__priv, __args...) \ - stmmac_do_void_callback(__priv, dma, enable_dma_transmission, __args) + stmmac_do_void_callback(__priv, dma, enable_dma_transmission, __priv, __args) #define stmmac_enable_dma_irq(__priv, __args...) \ stmmac_do_void_callback(__priv, dma, enable_dma_irq, __priv, __args) #define stmmac_disable_dma_irq(__priv, __args...) \drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +3
-3@@ -2558,7 +2558,7 @@ static bool stmmac_xdp_xmit_zc(struct stmmac_priv *priv, u32 queue, u32 budget) true, priv->mode, true, true, xdp_desc.len); -stmmac_enable_dma_transmission (priv, priv->ioaddr); +stmmac_enable_dma_transmission (priv, priv->ioaddr, queue);xsk_tx_metadata_to_compl (meta, &tx_q->tx_skbuff_dma[entry].xsk_meta);@@ -4679,7 +4679,7 @@ static netdev_tx_t stmmac_xmit(struct sk_buff *skb, struct net_device *dev)netdev_tx_sent_queue (netdev_get_tx_queue (dev, queue), skb->len); -stmmac_enable_dma_transmission (priv, priv->ioaddr); +stmmac_enable_dma_transmission (priv, priv->ioaddr, queue);stmmac_flush_tx_descriptors (priv, queue);stmmac_tx_timer_arm (priv, queue);@@ -4899,7 +4899,7 @@ static int stmmac_xdp_xmit_xdpf(struct stmmac_priv *priv, int queue,u64_stats_update_end_irqrestore (&txq_stats->syncp, flags); } -stmmac_enable_dma_transmission (priv, priv->ioaddr); +stmmac_enable_dma_transmission (priv, priv->ioaddr, queue); entry =STMMAC_GET_ENTRY (entry, priv->dma_conf.dma_tx_size); tx_q->cur_tx = entry;Signature · 1 line
2.31.4
PATCH v7 2/9 net: stmmac: dwmac-loongson: Refactor code for loongson_dwmac_probe()
In reply to Yanteng SiAdd a setup() function to initialize data, and simplify code for loongson_dwmac_probe().
--- .../ethernet/stmicro/stmmac/dwmac-loongson.c | 68 +++++++++++++------ 1 file changed, 47 insertions(+), 21 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +47 -21
@@ -9,7 +9,12 @@#include <linux/of_irq.h> #include "stmmac.h" -static int loongson_default_data (struct plat_stmmacenet_data *plat) +struct stmmac_pci_info { +int (*setup)(struct pci_dev *pdev,struct plat_stmmacenet_data *plat); +}; + +static void loongson_default_data (struct pci_dev *pdev, +struct plat_stmmacenet_data *plat) { plat->clk_csr =2 ;/* clk_csr_i = 20-35MHz & MDC = clk_csr_i/16 */ plat->has_gmac =1 ;
@@ -34,23 +39,38 @@ static int loongson_default_data(struct plat_stmmacenet_data *plat)/* Disable RX queues routing by default */ plat->rx_queues_cfg[0 ].pkt_route =0x0 ; +} + +static int loongson_gmac_data (struct pci_dev *pdev, +struct plat_stmmacenet_data *plat) +{ +loongson_default_data (pdev, plat); + + plat->multicast_filter_bins =256 ; + + plat->mdio_bus_data->phy_mask =0 ; -/* Default to phy auto-detection */ plat->phy_addr =-1 ; + plat->phy_interface =PHY_INTERFACE_MODE_RGMII_ID ; plat->dma_cfg->pbl =32 ; plat->dma_cfg->pblx8 = true; - plat->multicast_filter_bins =256 ;return 0 ; } -static int loongson_dwmac_probe (struct pci_dev *pdev,const struct pci_device_id *id) +static struct stmmac_pci_info loongson_gmac_pci_info = { + .setup = loongson_gmac_data, +}; + +static int loongson_dwmac_probe (struct pci_dev *pdev, +const struct pci_device_id *id) { +int ret, i, bus_id, phy_mode;struct plat_stmmacenet_data *plat; +struct stmmac_pci_info *info;struct stmmac_resources res;struct device_node *np; -int ret, i, phy_mode; np =dev_of_node (&pdev->dev);
@@ -69,22 +89,22 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_idif (!plat->mdio_bus_data)return -ENOMEM ; + plat->dma_cfg =devm_kzalloc (&pdev->dev,sizeof (*plat->dma_cfg), +GFP_KERNEL ); +if (!plat->dma_cfg) +return -ENOMEM ; + plat->mdio_node =of_get_child_by_name (np,"mdio" );if (plat->mdio_node) {dev_info (&pdev->dev,"Found MDIO subnode\n" ); plat->mdio_bus_data->needs_reset = true; } - plat->dma_cfg =devm_kzalloc (&pdev->dev,sizeof (*plat->dma_cfg),GFP_KERNEL ); -if (!plat->dma_cfg) { - ret = -ENOMEM ; - goto err_put_node; - } -/* Enable pci device */ ret =pci_enable_device (pdev);if (ret) { -dev_err (&pdev->dev,"%s: ERROR: failed to enable device\n" , __func__); +dev_err (&pdev->dev,"%s: ERROR: failed to enable device\n" , + __func__); goto err_put_node; }
@@ -98,9 +118,16 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_idbreak ; } - plat->bus_id =of_alias_get_id (np,"ethernet" ); -if (plat->bus_id <0 ) - plat->bus_id =pci_dev_id (pdev); +pci_set_master (pdev); + + info = (struct stmmac_pci_info *)id->driver_data; + ret = info->setup (pdev, plat); +if (ret) + goto err_disable_device; + + bus_id =of_alias_get_id (np,"ethernet" ); +if (bus_id >=0 ) + plat->bus_id = bus_id; phy_mode =device_get_phy_mode (&pdev->dev);if (phy_mode <0 ) {
@@ -110,11 +137,7 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id } plat->phy_interface = phy_mode; - plat->mac_interface =PHY_INTERFACE_MODE_GMII ; -pci_set_master (pdev); - -loongson_default_data (plat);pci_enable_msi (pdev);memset (&res,0 ,sizeof (res)); res.addr =pcim_iomap_table (pdev)[0 ];
@@ -128,7 +151,8 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id res.wol_irq =of_irq_get_byname (np,"eth_wake_irq" );if (res.wol_irq <0 ) { -dev_info (&pdev->dev,"IRQ eth_wake_irq not found, using macirq\n" ); +dev_info (&pdev->dev, +"IRQ eth_wake_irq not found, using macirq\n" ); res.wol_irq = res.irq; }
@@ -212,8 +236,10 @@ static int __maybe_unused loongson_dwmac_resume(struct device *dev) static SIMPLE_DEV_PM_OPS(loongson_dwmac_pm_ops, loongson_dwmac_suspend, loongson_dwmac_resume); +#define PCI_DEVICE_ID_LOONGSON_GMAC 0x7a03 +static const struct pci_device_id loongson_dwmac_id_table[] = { - {PCI_VDEVICE (LOONGSON ,0x7a03 ) }, + {PCI_DEVICE_DATA (LOONGSON ,GMAC , &loongson_gmac_pci_info) }, {} };MODULE_DEVICE_TABLE (pci, loongson_dwmac_id_table);
Signature · 1 line
2.31.4
Re: [PATCH net-next v7 2/9] net: stmmac: dwmac-loongson: Refactor code for loongson_dwmac_probe()
Quoted 2 lines · Yanteng Si
Add a
setup()function to initialize data, and simplify code forloongson_dwmac_probe().
Not all changes in this patch are described.
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_default_data(struct plat_stmmacenet_data *plat) · line 54
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +9
-1+static int loongson_gmac_data (struct pci_dev *pdev, +struct plat_stmmacenet_data *plat) +{ +loongson_default_data (pdev, plat); + + plat->multicast_filter_bins =256 ; + + plat->mdio_bus_data->phy_mask =0 ; -/* Default to phy auto-detection */ plat->phy_addr =-1 ; + plat->phy_interface =PHY_INTERFACE_MODE_RGMII_ID ;
This presumably sets the default phy_interface mode?
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id · line 126
Quoted 9 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +6
-3- plat->bus_id =of_alias_get_id (np,"ethernet" ); -if (plat->bus_id <0 ) - plat->bus_id =pci_dev_id (pdev); +pci_set_master (pdev); + + info = (struct stmmac_pci_info *)id->driver_data; + ret = info->setup (pdev, plat); +if (ret) + goto err_disable_device;
loongson_gmac_data() gets called from here...
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id · line 133
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +4
-0+ + bus_id =of_alias_get_id (np,"ethernet" ); +if (bus_id >=0 ) + plat->bus_id = bus_id; phy_mode =device_get_phy_mode (&pdev->dev);if (phy_mode <0 ) {
This gets the PHY interface mode, and errors out if it can't be found in firmware.
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id · line 139
Quoted 4 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +0
-0@@ -110,11 +137,7 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id } plat->phy_interface = phy_mode;
So this ends up always overwriting the value written in loongson_gmac_data(). So it seems to be that initialising plat->phy_interface in loongson_gmac_data() is just patch noise and serves no real purpose.
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id · line 113
Quoted 1 line
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +0
-1- plat->mac_interface =PHY_INTERFACE_MODE_GMII ;
This has now gone - and is not described, and I'm left wondering what the implication of that is on the driver. It also makes me wonder whether loongson_gmac_data() should've been setting mac_interface rather than phy_interface.
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id · line 155
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +2
-1res.wol_irq =of_irq_get_byname (np,"eth_wake_irq" );if (res.wol_irq <0 ) { -dev_info (&pdev->dev,"IRQ eth_wake_irq not found, using macirq\n" ); +dev_info (&pdev->dev, +"IRQ eth_wake_irq not found, using macirq\n" );
Whitespace cleanups should be a separate patch.
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
Re: [PATCH net-next v7 2/9] net: stmmac: dwmac-loongson: Refactor code for loongson_dwmac_probe()
Quoted 4 lines · Russell King (Oracle)
Quoted 2 lines · Yanteng Si
Add a
setup()function to initialize data, and simplify code forloongson_dwmac_probe().Not all changes in this patch are described.
Okay, I'll re-write it in more detail.
Quoted 46 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_default_data(struct plat_stmmacenet_data *plat) · line 54
Quoted 13 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +9
-1+static int loongson_gmac_data (struct pci_dev *pdev, +struct plat_stmmacenet_data *plat) +{ +loongson_default_data (pdev, plat); + + plat->multicast_filter_bins =256 ; + + plat->mdio_bus_data->phy_mask =0 ; -/* Default to phy auto-detection */ plat->phy_addr =-1 ; + plat->phy_interface =PHY_INTERFACE_MODE_RGMII_ID ;This presumably sets the default
phy_interfacemode?drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id · line 126
Quoted 9 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +6
-3- plat->bus_id =of_alias_get_id (np,"ethernet" ); -if (plat->bus_id <0 ) - plat->bus_id =pci_dev_id (pdev); +pci_set_master (pdev); + + info = (struct stmmac_pci_info *)id->driver_data; + ret = info->setup (pdev, plat); +if (ret) + goto err_disable_device;
loongson_gmac_data()gets called from here...drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id · line 133
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +4
-0+ + bus_id =of_alias_get_id (np,"ethernet" ); +if (bus_id >=0 ) + plat->bus_id = bus_id; phy_mode =device_get_phy_mode (&pdev->dev);if (phy_mode <0 ) {This gets the PHY interface mode, and errors out if it can't be found in firmware.
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id · line 139
Quoted 4 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +0
-0@@ -110,11 +137,7 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id } plat->phy_interface = phy_mode;So this ends up always overwriting the value written in
loongson_gmac_data(). So it seems to be that initialisingplat->phy_interfaceinloongson_gmac_data()is just patch noise and serves no real purpose.
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id · line 113
Quoted 1 line
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +0
-1- plat->mac_interface =PHY_INTERFACE_MODE_GMII ;This has now gone - and is not described, and I'm left wondering what the implication of that is on the driver. It also makes me wonder whether
loongson_gmac_data()should've been settingmac_interfacerather thanphy_interface.
You seem to have understood this in Patch 3.
I'll re-split the patch to make the code easier to understand.
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id · line 155
Quoted 6 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +2
-1res.wol_irq =of_irq_get_byname (np,"eth_wake_irq" );if (res.wol_irq <0 ) { -dev_info (&pdev->dev,"IRQ eth_wake_irq not found, using macirq\n" ); +dev_info (&pdev->dev, +"IRQ eth_wake_irq not found, using macirq\n" );Whitespace cleanups should be a separate patch.
OK.
Thanks,
Yanteng
Quoted 1 line
PATCH v7 3/9 net: stmmac: dwmac-loongson: Add full PCI support
In reply to Yanteng SiCurrent dwmac-loongson only support LS2K in the "probed with PCI and configured with DT" manner. Add LS7A support on which the devices are fully PCI (non-DT).
--- .../ethernet/stmicro/stmmac/dwmac-loongson.c | 79 ++++++++++--------- 1 file changed, 43 insertions(+), 36 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +43 -36
@@ -16,6 +16,10 @@ struct stmmac_pci_info {static void loongson_default_data (struct pci_dev *pdev,struct plat_stmmacenet_data *plat) { +/* Get bus_id, this can be overloaded later */ + plat->bus_id = (pci_domain_nr (pdev->bus) <<16 ) | +PCI_DEVID (pdev->bus->number, pdev->devfn); + plat->clk_csr =2 ;/* clk_csr_i = 20-35MHz & MDC = clk_csr_i/16 */ plat->has_gmac =1 ; plat->force_sf_dma_mode =1 ;
@@ -56,6 +60,9 @@ static int loongson_gmac_data(struct pci_dev *pdev, plat->dma_cfg->pbl =32 ; plat->dma_cfg->pblx8 = true; + plat->clk_ref_rate =125000000 ; + plat->clk_ptp_rate =125000000 ; +return 0 ; }
@@ -72,13 +79,6 @@ static int loongson_dwmac_probe(struct pci_dev *pdev,struct stmmac_resources res;struct device_node *np; - np =dev_of_node (&pdev->dev); - -if (!np) { -pr_info ("dwmac_loongson_pci: No OF node\n" ); -return -ENODEV ; - } - plat =devm_kzalloc (&pdev->dev,sizeof (*plat),GFP_KERNEL );if (!plat)return -ENOMEM ;
@@ -94,6 +94,7 @@ static int loongson_dwmac_probe(struct pci_dev *pdev,if (!plat->dma_cfg)return -ENOMEM ; + np =dev_of_node (&pdev->dev); plat->mdio_node =of_get_child_by_name (np,"mdio" );if (plat->mdio_node) {dev_info (&pdev->dev,"Found MDIO subnode\n" );
@@ -125,42 +126,48 @@ static int loongson_dwmac_probe(struct pci_dev *pdev,if (ret) goto err_disable_device; - bus_id =of_alias_get_id (np,"ethernet" ); -if (bus_id >=0 ) - plat->bus_id = bus_id; +if (np) { + bus_id =of_alias_get_id (np,"ethernet" ); +if (bus_id >=0 ) + plat->bus_id = bus_id; - phy_mode =device_get_phy_mode (&pdev->dev); -if (phy_mode <0 ) { -dev_err (&pdev->dev,"phy_mode not found\n" ); - ret = phy_mode; - goto err_disable_device; + phy_mode =device_get_phy_mode (&pdev->dev); +if (phy_mode <0 ) { +dev_err (&pdev->dev,"phy_mode not found\n" ); + ret = phy_mode; + goto err_disable_device; + } + plat->phy_interface = phy_mode; } - plat->phy_interface = phy_mode; -pci_enable_msi (pdev);memset (&res,0 ,sizeof (res)); res.addr =pcim_iomap_table (pdev)[0 ]; - res.irq =of_irq_get_byname (np,"macirq" ); -if (res.irq <0 ) { -dev_err (&pdev->dev,"IRQ macirq not found\n" ); - ret = -ENODEV ; - goto err_disable_msi; - } - - res.wol_irq =of_irq_get_byname (np,"eth_wake_irq" ); -if (res.wol_irq <0 ) { -dev_info (&pdev->dev, -"IRQ eth_wake_irq not found, using macirq\n" ); - res.wol_irq = res.irq; - } - - res.lpi_irq =of_irq_get_byname (np,"eth_lpi" ); -if (res.lpi_irq <0 ) { -dev_err (&pdev->dev,"IRQ eth_lpi not found\n" ); - ret = -ENODEV ; - goto err_disable_msi; +if (np) { + res.irq =of_irq_get_byname (np,"macirq" ); +if (res.irq <0 ) { +dev_err (&pdev->dev,"IRQ macirq not found\n" ); + ret = -ENODEV ; + goto err_disable_msi; + } + + res.wol_irq =of_irq_get_byname (np,"eth_wake_irq" ); +if (res.wol_irq <0 ) { +dev_info (&pdev->dev, +"IRQ eth_wake_irq not found, using macirq\n" ); + res.wol_irq = res.irq; + } + + res.lpi_irq =of_irq_get_byname (np,"eth_lpi" ); +if (res.lpi_irq <0 ) { +dev_err (&pdev->dev,"IRQ eth_lpi not found\n" ); + ret = -ENODEV ; + goto err_disable_msi; + } + }else { + res.irq = pdev->irq; + res.wol_irq = pdev->irq; } ret =stmmac_dvr_probe (&pdev->dev, plat, &res);
Signature · 1 line
2.31.4
Re: [PATCH net-next v7 3/9] net: stmmac: dwmac-loongson: Add full PCI support
Quoted 18 lines · Yanteng Si
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +5
-8@@ -125,42 +126,48 @@ static int loongson_dwmac_probe(struct pci_dev *pdev,if (ret) goto err_disable_device; - bus_id =of_alias_get_id (np,"ethernet" ); -if (bus_id >=0 ) - plat->bus_id = bus_id; +if (np) { + bus_id =of_alias_get_id (np,"ethernet" ); +if (bus_id >=0 ) + plat->bus_id = bus_id; - phy_mode =device_get_phy_mode (&pdev->dev); -if (phy_mode <0 ) { -dev_err (&pdev->dev,"phy_mode not found\n" ); - ret = phy_mode; - goto err_disable_device; + phy_mode =device_get_phy_mode (&pdev->dev);
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_dwmac_probe(struct pci_dev *pdev, · line 140
Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +6
-2+if (phy_mode <0 ) { +dev_err (&pdev->dev,"phy_mode not found\n" ); + ret = phy_mode; + goto err_disable_device; + } + plat->phy_interface = phy_mode; } - plat->phy_interface = phy_mode; -
So this is why phy_interface changes in patch 2. It would have been good to make a forward reference to this change to explain in patch 2 why the "default" value has been set there. Or maybe move the setting of that default value into this patch?
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
Re: [PATCH net-next v7 3/9] net: stmmac: dwmac-loongson: Add full PCI support
Quoted 27 lines · Russell King (Oracle)
Quoted 26 lines · Yanteng Si
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +11
-8@@ -125,42 +126,48 @@ static int loongson_dwmac_probe(struct pci_dev *pdev,if (ret) goto err_disable_device; - bus_id =of_alias_get_id (np,"ethernet" ); -if (bus_id >=0 ) - plat->bus_id = bus_id; +if (np) { + bus_id =of_alias_get_id (np,"ethernet" ); +if (bus_id >=0 ) + plat->bus_id = bus_id; - phy_mode =device_get_phy_mode (&pdev->dev); -if (phy_mode <0 ) { -dev_err (&pdev->dev,"phy_mode not found\n" ); - ret = phy_mode; - goto err_disable_device; + phy_mode =device_get_phy_mode (&pdev->dev); +if (phy_mode <0 ) { +dev_err (&pdev->dev,"phy_mode not found\n" ); + ret = phy_mode; + goto err_disable_device; + } + plat->phy_interface = phy_mode; }
Quoted 6 lines
Review static int loongson_dwmac_probe(struct pci_dev *pdev, · line 140
Quoted 2 lines
(quoted diff) +0
-2- plat->phy_interface = phy_mode; -So this is why
phy_interfacechanges in patch 2. It would have been good to make a forward reference to this change to explain in patch 2 why the "default" value has been set there. Or maybe move the setting of that default value into this patch?
Thank you for your review. Sorry, I have been modifying the code according to serge's
comments for the past 10 days. I have not forgotten your comment. I will reply to you
next week.
Thanks,
Yanteng
Quoted 1 line
Re: [PATCH net-next v7 3/9] net: stmmac: dwmac-loongson: Add full PCI support
In reply to Russell King (Oracle)Quoted 27 lines · Russell King (Oracle)
Quoted 26 lines · Yanteng Si
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +11
-8@@ -125,42 +126,48 @@ static int loongson_dwmac_probe(struct pci_dev *pdev,if (ret) goto err_disable_device; - bus_id =of_alias_get_id (np,"ethernet" ); -if (bus_id >=0 ) - plat->bus_id = bus_id; +if (np) { + bus_id =of_alias_get_id (np,"ethernet" ); +if (bus_id >=0 ) + plat->bus_id = bus_id; - phy_mode =device_get_phy_mode (&pdev->dev); -if (phy_mode <0 ) { -dev_err (&pdev->dev,"phy_mode not found\n" ); - ret = phy_mode; - goto err_disable_device; + phy_mode =device_get_phy_mode (&pdev->dev); +if (phy_mode <0 ) { +dev_err (&pdev->dev,"phy_mode not found\n" ); + ret = phy_mode; + goto err_disable_device; + } + plat->phy_interface = phy_mode; }
Quoted 6 lines
Review static int loongson_dwmac_probe(struct pci_dev *pdev, · line 140
Quoted 2 lines
(quoted diff) +0
-2- plat->phy_interface = phy_mode; -So this is why
phy_interfacechanges in patch 2. It would have been good to make a forward reference to this change to explain in patch 2 why the "default" value has been set there. Or maybe move the setting of that default value into this patch?
This sounds great, I will try it.
Thanks,
Yanteng
Quoted 1 line
PATCH v7 4/9 net: stmmac: Add multi-channel supports
In reply to Yanteng SiLoongson platforms use a DWGMAC which supports multi-channel.
Added dwmac1000_dma_init_channel() and init_chan(), factor out all the channel-specific setups from dwmac1000_dma_init() to the new function dma_config(), then distinguish dma initialization and multi-channel initialization through different parameters.
--- .../ethernet/stmicro/stmmac/dwmac1000_dma.c | 55 ++++++++++++++----- .../net/ethernet/stmicro/stmmac/dwmac_dma.h | 17 ++++++ .../net/ethernet/stmicro/stmmac/dwmac_lib.c | 30 +++++----- 3 files changed, 74 insertions(+), 28 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +42 -13
@@ -12,7 +12,8 @@Author: Giuseppe Cavallaro <[email protected]> *******************************************************************************/ -#include <asm/io.h> +#include <linux/io.h> +#include "stmmac.h" #include "dwmac1000.h" #include "dwmac_dma.h"
@@ -70,13 +71,16 @@ static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi)writel (value, ioaddr +DMA_AXI_BUS_MODE ); } -static void dwmac1000_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr, -struct stmmac_dma_cfg *dma_cfg,int atds) +static void dma_config (void __iomem *modeaddr,void __iomem *enaddr, +struct stmmac_dma_cfg *dma_cfg,u32 dma_intr_mask, +int atds) { -u32 value =readl (ioaddr +DMA_BUS_MODE ); +u32 value;int txpbl = dma_cfg->txpbl ?: dma_cfg->pbl;int rxpbl = dma_cfg->rxpbl ?: dma_cfg->pbl; + value =readl (modeaddr); +/* * Set the DMA PBL (Programmable Burst Length) mode. *
@@ -104,10 +108,34 @@ static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr,if (dma_cfg->aal) value |=DMA_BUS_MODE_AAL ; -writel (value, ioaddr +DMA_BUS_MODE ); +writel (value, modeaddr); +writel (dma_intr_mask, enaddr); +} + +static void dwmac1000_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr, +struct stmmac_dma_cfg *dma_cfg,int atds) +{ +u32 dma_intr_mask;/* Mask interrupts by writing to CSR7 */ -writel (DMA_INTR_DEFAULT_MASK , ioaddr +DMA_INTR_ENA ); + dma_intr_mask =DMA_INTR_DEFAULT_MASK ; + +dma_config (ioaddr +DMA_BUS_MODE , ioaddr +DMA_INTR_ENA , + dma_cfg, dma_intr_mask, atds); +} + +static void dwmac1000_dma_init_channel (struct stmmac_priv *priv,void __iomem *ioaddr, +struct stmmac_dma_cfg *dma_cfg,u32 chan) +{ +u32 dma_intr_mask; + +/* Mask interrupts by writing to CSR7 */ + dma_intr_mask =DMA_INTR_DEFAULT_MASK ; + +if (dma_cfg->multi_msi_en) +dma_config (ioaddr +DMA_CHAN_BUS_MODE (chan), + ioaddr +DMA_CHAN_INTR_ENA (chan), dma_cfg, + dma_intr_mask, dma_cfg->multi_msi_en); } static void dwmac1000_dma_init_rx(struct stmmac_priv *priv,
@@ -116,7 +144,7 @@ static void dwmac1000_dma_init_rx(struct stmmac_priv *priv, dma_addr_t dma_rx_phy, u32 chan) {/* RX descriptor base address list must be written into DMA CSR3 */ - writel(lower_32_bits(dma_rx_phy), ioaddr + DMA_RCV_BASE_ADDR); + writel(lower_32_bits(dma_rx_phy), ioaddr + DMA_CHAN_RCV_BASE_ADDR(chan)); } static void dwmac1000_dma_init_tx(struct stmmac_priv *priv,
@@ -125,7 +153,7 @@ static void dwmac1000_dma_init_tx(struct stmmac_priv *priv, dma_addr_t dma_tx_phy, u32 chan) {/* TX descriptor base address list must be written into DMA CSR4 */ - writel(lower_32_bits(dma_tx_phy), ioaddr + DMA_TX_BASE_ADDR); + writel(lower_32_bits(dma_tx_phy), ioaddr + DMA_CHAN_TX_BASE_ADDR(chan)); }static u32 dwmac1000_configure_fc (u32 csr6,int rxfifosz)
@@ -153,7 +181,7 @@ static void dwmac1000_dma_operation_mode_rx(struct stmmac_priv *priv, void __iomem *ioaddr, int mode, u32 channel, int fifosz, u8 qmode) { - u32 csr6 = readl(ioaddr + DMA_CONTROL); + u32 csr6 = readl(ioaddr + DMA_CHAN_CONTROL(channel));if (mode ==SF_DMA_MODE ) {pr_debug ("GMAC: enable RX store and forward mode\n" );
@@ -175,14 +203,14 @@ static void dwmac1000_dma_operation_mode_rx(struct stmmac_priv *priv,/* Configure flow control based on rx fifo size */ csr6 =dwmac1000_configure_fc (csr6, fifosz); -writel (csr6, ioaddr +DMA_CONTROL ); +writel (csr6, ioaddr +DMA_CHAN_CONTROL (channel)); }static void dwmac1000_dma_operation_mode_tx (struct stmmac_priv *priv,void __iomem *ioaddr,int mode,u32 channel,int fifosz,u8 qmode) { -u32 csr6 =readl (ioaddr +DMA_CONTROL ); +u32 csr6 =readl (ioaddr +DMA_CHAN_CONTROL (channel));if (mode ==SF_DMA_MODE ) {pr_debug ("GMAC: enable TX store and forward mode\n" );
@@ -209,7 +237,7 @@ static void dwmac1000_dma_operation_mode_tx(struct stmmac_priv *priv, csr6 |=DMA_CONTROL_TTC_256 ; } -writel (csr6, ioaddr +DMA_CONTROL ); +writel (csr6, ioaddr +DMA_CHAN_CONTROL (channel)); } static void dwmac1000_dump_dma_regs(struct stmmac_priv *priv,
@@ -271,12 +299,13 @@ static int dwmac1000_get_hw_feature(void __iomem *ioaddr,static void dwmac1000_rx_watchdog (struct stmmac_priv *priv,void __iomem *ioaddr,u32 riwt,u32 queue) { -writel (riwt, ioaddr +DMA_RX_WATCHDOG ); +writel (riwt, ioaddr +DMA_CHAN_RX_WATCHDOG (queue)); }const struct stmmac_dma_ops dwmac1000_dma_ops = { .reset = dwmac_dma_reset, .init = dwmac1000_dma_init, + .init_chan = dwmac1000_dma_init_channel, .init_rx_chan = dwmac1000_dma_init_rx, .init_tx_chan = dwmac1000_dma_init_tx, .axi = dwmac1000_dma_axi,
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +17 -0
@@ -148,6 +148,9 @@ DMA_STATUS_TI | \ DMA_STATUS_MSK_COMMON) +/* Following DMA defines are chanels oriented */ +#define DMA_CHAN_OFFSET 0x100 +#define NUM_DWMAC100_DMA_REGS 9#define NUM_DWMAC1000_DMA_REGS 23#define NUM_DWMAC4_DMA_REGS 27
@@ -170,4 +173,18 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr, struct stmmac_extra_stats *x, u32 chan, u32 dir);int dwmac_dma_reset (void __iomem *ioaddr); +static inline u32 dma_chan_base_addr (u32 base,u32 chan) +{ +return base + chan *DMA_CHAN_OFFSET ; +} + +#define DMA_CHAN_XMT_POLL_DEMAND (chan) dma_chan_base_addr(DMA_XMT_POLL_DEMAND, chan) +#define DMA_CHAN_INTR_ENA (chan) dma_chan_base_addr(DMA_INTR_ENA, chan) +#define DMA_CHAN_CONTROL (chan) dma_chan_base_addr(DMA_CONTROL, chan) +#define DMA_CHAN_STATUS (chan) dma_chan_base_addr(DMA_STATUS, chan) +#define DMA_CHAN_BUS_MODE (chan) dma_chan_base_addr(DMA_BUS_MODE, chan) +#define DMA_CHAN_RCV_BASE_ADDR (chan) dma_chan_base_addr(DMA_RCV_BASE_ADDR, chan) +#define DMA_CHAN_TX_BASE_ADDR (chan) dma_chan_base_addr(DMA_TX_BASE_ADDR, chan) +#define DMA_CHAN_RX_WATCHDOG (chan) dma_chan_base_addr(DMA_RX_WATCHDOG, chan) +#endif /* __DWMAC_DMA_H__ */
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +15 -15
@@ -31,63 +31,63 @@ int dwmac_dma_reset(void __iomem *ioaddr)void dwmac_enable_dma_transmission (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -writel (1 , ioaddr +DMA_XMT_POLL_DEMAND ); +writel (1 , ioaddr +DMA_CHAN_XMT_POLL_DEMAND (chan)); }void dwmac_enable_dma_irq (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan,bool rx,bool tx) { -u32 value =readl (ioaddr +DMA_INTR_ENA ); +u32 value =readl (ioaddr +DMA_CHAN_INTR_ENA (chan));if (rx) value |=DMA_INTR_DEFAULT_RX ;if (tx) value |=DMA_INTR_DEFAULT_TX ; -writel (value, ioaddr +DMA_INTR_ENA ); +writel (value, ioaddr +DMA_CHAN_INTR_ENA (chan)); }void dwmac_disable_dma_irq (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan,bool rx,bool tx) { -u32 value =readl (ioaddr +DMA_INTR_ENA ); +u32 value =readl (ioaddr +DMA_CHAN_INTR_ENA (chan));if (rx) value &= ~DMA_INTR_DEFAULT_RX ;if (tx) value &= ~DMA_INTR_DEFAULT_TX ; -writel (value, ioaddr +DMA_INTR_ENA ); +writel (value, ioaddr +DMA_CHAN_INTR_ENA (chan)); }void dwmac_dma_start_tx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value |=DMA_CONTROL_ST ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }void dwmac_dma_stop_tx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value &= ~DMA_CONTROL_ST ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }void dwmac_dma_start_rx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value |=DMA_CONTROL_SR ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }void dwmac_dma_stop_rx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value &= ~DMA_CONTROL_SR ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }#ifdef DWMAC_DMA_DEBUG
@@ -167,7 +167,7 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,struct stmmac_txq_stats *txq_stats = &priv->xstats.txq_stats[chan];int ret =0 ;/* read the status register (CSR5) */ -u32 intr_status =readl (ioaddr +DMA_STATUS ); +u32 intr_status =readl (ioaddr +DMA_CHAN_STATUS (chan));#ifdef DWMAC_DMA_DEBUG /* Enable it to monitor DMA rx/tx status in case of critical problems */
@@ -237,7 +237,7 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,pr_warn ("%s: unexpected status %08x\n" , __func__, intr_status);/* Clear the interrupt by writing a logic 1 to the CSR5[15-0] */ -writel ((intr_status &0x1ffff ), ioaddr +DMA_STATUS ); +writel ((intr_status &0x7ffff ), ioaddr +DMA_CHAN_STATUS (chan));return ret; }
Signature · 1 line
2.31.4
Re: [PATCH net-next v7 4/9] net: stmmac: Add multi-channel supports
Quoted 31 lines · Yanteng Si
Loongson platforms use a DWGMAC which supports multi-channel.
Added
dwmac1000_dma_init_channel()andinit_chan(), factor out all the channel-specific setups fromdwmac1000_dma_init()to the new functiondma_config(), then distinguish dma initialization and multi-channel initialization through different parameters.Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- .../ethernet/stmicro/stmmac/dwmac1000_dma.c | 55 ++++++++++++++----- .../net/ethernet/stmicro/stmmac/dwmac_dma.h | 17 ++++++ .../net/ethernet/stmicro/stmmac/dwmac_lib.c | 30 +++++----- 3 files changed, 74 insertions(+), 28 deletions(-)drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +2
-1@@ -12,7 +12,8 @@Author: Giuseppe Cavallaro <[email protected]> *******************************************************************************/ -#include <asm/io.h> +#include <linux/io.h> +#include "stmmac.h" #include "dwmac1000.h" #include "dwmac_dma.h"
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi) · line 77
Quoted 9 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +3
-2@@ -70,13 +71,16 @@ static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi)writel (value, ioaddr +DMA_AXI_BUS_MODE ); } -static void dwmac1000_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr, -struct stmmac_dma_cfg *dma_cfg,int atds) +static void dma_config (void __iomem *modeaddr,void __iomem *enaddr, +struct stmmac_dma_cfg *dma_cfg,u32 dma_intr_mask, +int atds)
Please make sure the arguments are aligned with the function open parenthesis taking into account that tabs are of _8_ chars:Documentation/process/coding-style.rst.
Quoted 35 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +3
-1{ -u32 value =readl (ioaddr +DMA_BUS_MODE ); +u32 value;int txpbl = dma_cfg->txpbl ?: dma_cfg->pbl;int rxpbl = dma_cfg->rxpbl ?: dma_cfg->pbl; + value =readl (modeaddr); +/* * Set the DMA PBL (Programmable Burst Length) mode. drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +15
-2* @@ -104,10 +108,34 @@ static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr,if (dma_cfg->aal) value |=DMA_BUS_MODE_AAL ; -writel (value, ioaddr +DMA_BUS_MODE ); +writel (value, modeaddr); +writel (dma_intr_mask, enaddr); +} + +static void dwmac1000_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr, +struct stmmac_dma_cfg *dma_cfg,int atds) +{ +u32 dma_intr_mask;/* Mask interrupts by writing to CSR7 */ -writel (DMA_INTR_DEFAULT_MASK , ioaddr +DMA_INTR_ENA ); + dma_intr_mask =DMA_INTR_DEFAULT_MASK ; + +dma_config (ioaddr +DMA_BUS_MODE , ioaddr +DMA_INTR_ENA , + dma_cfg, dma_intr_mask, atds); +} + +static void dwmac1000_dma_init_channel(struct stmmac_priv *priv, void __iomem *ioaddr,
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr, · line 138
Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +10
-0+ struct stmmac_dma_cfg *dma_cfg, u32 chan) +{ +u32 dma_intr_mask; + +/* Mask interrupts by writing to CSR7 */ + dma_intr_mask =DMA_INTR_DEFAULT_MASK ; + +if (dma_cfg->multi_msi_en) + dma_config(ioaddr + DMA_CHAN_BUS_MODE(chan), + ioaddr + DMA_CHAN_INTR_ENA(chan), dma_cfg,
Why so complicated? stmmac_init_chan() is always supposed to be called in the same context as stmmac_dma_init() (stmmac_xdp_open() is wrong in not doing that). Seeing DW GMAC v3.x multi-channels feature is implemented as multiple sets of the same CSRs (except AV traffic control CSRs specific to channels 1 and higher which are left unused here anyway) you can just drop the stmmac_dma_ops.init() callback and convert dwmac1000_dma_init() to being dwmac1000_dma_init_channel() with no significant modifications:
< you wouldn't need to have a separate dma_config() method. < you wouldn't need to check for the dma_cfg->multi_msi_en flag state since the stmmac_init_chan() method is called for as many times as there are channels available (at least 1 channel always exists). < just add atds argument.
< just convert the method to using the chan-dependent CSR macros.
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr, · line 138
Quoted 1 line
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +1
-0+ dma_intr_mask, dma_cfg->multi_msi_en);
^
+-------------------------------------------------+This is wrong + ATDS flag means Alternative Descriptor Size. This flag enables the 8 dword DMA-descriptors size with some DMA-desc fields semantics changed (see enh_desc.c and norm_desc.c). It's useful for PTP Timestamping, VLANs, AV feature, L3/L4 filtering, CSum offload Type 2 (if any of that available). It has nothing to do with the separate DMA IRQs. Just convert the stmmac_dma_ops.dma_init() callback to accepting the atds flag as an additional argument, use it here to activate the extended descriptor size and make sure the atds flag is passed to the stmmac_init_chan() method in the respective source code.
Quoted 58 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +0
-0}static void dwmac1000_dma_init_rx(struct
stmmac_priv*priv,drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +6
-6@@ -116,7 +144,7 @@ static void dwmac1000_dma_init_rx(struct stmmac_priv *priv, dma_addr_t dma_rx_phy, u32 chan) {/* RX descriptor base address list must be written into DMA CSR3 */ - writel(lower_32_bits(dma_rx_phy), ioaddr + DMA_RCV_BASE_ADDR); + writel(lower_32_bits(dma_rx_phy), ioaddr + DMA_CHAN_RCV_BASE_ADDR(chan)); } static void dwmac1000_dma_init_tx(struct stmmac_priv *priv,@@ -125,7 +153,7 @@ static void dwmac1000_dma_init_tx(struct stmmac_priv *priv, dma_addr_t dma_tx_phy, u32 chan) {/* TX descriptor base address list must be written into DMA CSR4 */ - writel(lower_32_bits(dma_tx_phy), ioaddr + DMA_TX_BASE_ADDR); + writel(lower_32_bits(dma_tx_phy), ioaddr + DMA_CHAN_TX_BASE_ADDR(chan)); }static u32 dwmac1000_configure_fc (u32 csr6,int rxfifosz)@@ -153,7 +181,7 @@ static void dwmac1000_dma_operation_mode_rx(struct stmmac_priv *priv, void __iomem *ioaddr, int mode, u32 channel, int fifosz, u8 qmode) { - u32 csr6 = readl(ioaddr + DMA_CONTROL); + u32 csr6 = readl(ioaddr + DMA_CHAN_CONTROL(channel));if (mode ==SF_DMA_MODE ) {pr_debug ("GMAC: enable RX store and forward mode\n" );@@ -175,14 +203,14 @@ static void dwmac1000_dma_operation_mode_rx(struct stmmac_priv *priv,/* Configure flow control based on rx fifo size */ csr6 =dwmac1000_configure_fc (csr6, fifosz); -writel (csr6, ioaddr +DMA_CONTROL ); +writel (csr6, ioaddr +DMA_CHAN_CONTROL (channel)); }static void dwmac1000_dma_operation_mode_tx (struct stmmac_priv *priv,void __iomem *ioaddr,int mode,u32 channel,int fifosz,u8 qmode) { -u32 csr6 =readl (ioaddr +DMA_CONTROL ); +u32 csr6 =readl (ioaddr +DMA_CHAN_CONTROL (channel));if (mode ==SF_DMA_MODE ) {pr_debug ("GMAC: enable TX store and forward mode\n" );@@ -209,7 +237,7 @@ static void dwmac1000_dma_operation_mode_tx(struct stmmac_priv *priv, csr6 |=DMA_CONTROL_TTC_256 ; } -writel (csr6, ioaddr +DMA_CONTROL ); +writel (csr6, ioaddr +DMA_CHAN_CONTROL (channel)); } static void dwmac1000_dump_dma_regs(struct stmmac_priv *priv,@@ -271,12 +299,13 @@ static int dwmac1000_get_hw_feature(void __iomem *ioaddr, static void dwmac1000_rx_watchdog(struct stmmac_priv *priv,
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static int dwmac1000_get_hw_feature(void __iomem *ioaddr, · line 308
Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +1
-1void __iomem *ioaddr, u32 riwt, u32 queue) { - writel(riwt, ioaddr + DMA_RX_WATCHDOG); + writel(riwt, ioaddr + DMA_CHAN_RX_WATCHDOG(queue)); }const struct stmmac_dma_ops dwmac1000_dma_ops = { .reset = dwmac_dma_reset, .init = dwmac1000_dma_init,
This could be dropped. See my comment above.
Quoted 9 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +1
-0+ .init_chan = dwmac1000_dma_init_channel, .init_rx_chan = dwmac1000_dma_init_rx, .init_tx_chan = dwmac1000_dma_init_tx,drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +0
-0.axi = dwmac1000_dma_axi,drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +0
-0
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h line 152
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +1
-0@@ -148,6 +148,9 @@DMA_STATUS_TI | \ DMA_STATUS_MSK_COMMON) +/* Following DMA defines are chanels oriented */
s/chanels/channels
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h line 152
Quoted 1 line
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +1
-0+#define DMA_CHAN_OFFSET 0x100
DMA_CHAN_BASE_OFFSET? to be looking the same as in DW QoS Eth GMAC v4.x/v5.x (dwmac4_dma.h).
Quoted 114 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +1
-0+#define NUM_DWMAC100_DMA_REGS 9#define NUM_DWMAC1000_DMA_REGS 23#define
NUM_DWMAC4_DMA_REGS27drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +14
-0@@ -170,4 +173,18 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr, struct stmmac_extra_stats *x, u32 chan, u32 dir);int dwmac_dma_reset (void __iomem *ioaddr); +static inline u32 dma_chan_base_addr (u32 base,u32 chan) +{ +return base + chan *DMA_CHAN_OFFSET ; +} + +#define DMA_CHAN_XMT_POLL_DEMAND (chan) dma_chan_base_addr(DMA_XMT_POLL_DEMAND, chan) +#define DMA_CHAN_INTR_ENA (chan) dma_chan_base_addr(DMA_INTR_ENA, chan) +#define DMA_CHAN_CONTROL (chan) dma_chan_base_addr(DMA_CONTROL, chan) +#define DMA_CHAN_STATUS (chan) dma_chan_base_addr(DMA_STATUS, chan) +#define DMA_CHAN_BUS_MODE (chan) dma_chan_base_addr(DMA_BUS_MODE, chan) +#define DMA_CHAN_RCV_BASE_ADDR (chan) dma_chan_base_addr(DMA_RCV_BASE_ADDR, chan) +#define DMA_CHAN_TX_BASE_ADDR (chan) dma_chan_base_addr(DMA_TX_BASE_ADDR, chan) +#define DMA_CHAN_RX_WATCHDOG (chan) dma_chan_base_addr(DMA_RX_WATCHDOG, chan) +#endif /* __DWMAC_DMA_H__ */ drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +14
-14@@ -31,63 +31,63 @@ int dwmac_dma_reset(void __iomem *ioaddr)void dwmac_enable_dma_transmission (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -writel (1 , ioaddr +DMA_XMT_POLL_DEMAND ); +writel (1 , ioaddr +DMA_CHAN_XMT_POLL_DEMAND (chan)); }void dwmac_enable_dma_irq (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan,bool rx,bool tx) { -u32 value =readl (ioaddr +DMA_INTR_ENA ); +u32 value =readl (ioaddr +DMA_CHAN_INTR_ENA (chan));if (rx) value |=DMA_INTR_DEFAULT_RX ;if (tx) value |=DMA_INTR_DEFAULT_TX ; -writel (value, ioaddr +DMA_INTR_ENA ); +writel (value, ioaddr +DMA_CHAN_INTR_ENA (chan)); }void dwmac_disable_dma_irq (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan,bool rx,bool tx) { -u32 value =readl (ioaddr +DMA_INTR_ENA ); +u32 value =readl (ioaddr +DMA_CHAN_INTR_ENA (chan));if (rx) value &= ~DMA_INTR_DEFAULT_RX ;if (tx) value &= ~DMA_INTR_DEFAULT_TX ; -writel (value, ioaddr +DMA_INTR_ENA ); +writel (value, ioaddr +DMA_CHAN_INTR_ENA (chan)); }void dwmac_dma_start_tx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value |=DMA_CONTROL_ST ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }void dwmac_dma_stop_tx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value &= ~DMA_CONTROL_ST ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }void dwmac_dma_start_rx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value |=DMA_CONTROL_SR ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }void dwmac_dma_stop_rx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value &= ~DMA_CONTROL_SR ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }#ifdef DWMAC_DMA_DEBUG @@ -167,7 +167,7 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,struct stmmac_txq_stats *txq_stats = &priv->xstats.txq_stats[chan];int ret =0 ;/* read the status register (CSR5) */ -u32 intr_status =readl (ioaddr +DMA_STATUS ); +u32 intr_status =readl (ioaddr +DMA_CHAN_STATUS (chan));#ifdef DWMAC_DMA_DEBUG /* Enable it to monitor DMA rx/tx status in case of critical problems */
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr, · line 241
Quoted 6 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +1
-1@@ -237,7 +237,7 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,pr_warn ("%s: unexpected status %08x\n" , __func__, intr_status);/* Clear the interrupt by writing a logic 1 to the CSR5[15-0] */ -writel ((intr_status &0x1ffff ), ioaddr +DMA_STATUS ); +writel ((intr_status &0x7ffff ), ioaddr +DMA_CHAN_STATUS (chan));
Em, please explain the mask change. Bits CSR5[17:28] are defined as RO on a normal DW GMAC. Anyway it seems like the mask changes belongs to the patch 5/9.
Except the last comment, AFAICS this patch provides a generic DW GMAC v3.x multi-channel support. Despite of several issues noted above the change in general looks very good.
-Serge(y)
Quoted 6 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +0
-0return ret; }Signature · 1 line
2.31.4
Re: [PATCH net-next v7 4/9] net: stmmac: Add multi-channel supports
Quoted 35 lines · Serge Semin
Quoted 34 lines · Yanteng Si
Loongson platforms use a DWGMAC which supports multi-channel.
Added
dwmac1000_dma_init_channel()andinit_chan(), factor out all the channel-specific setups fromdwmac1000_dma_init()to the new functiondma_config(), then distinguish dma initialization and multi-channel initialization through different parameters.Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- .../ethernet/stmicro/stmmac/dwmac1000_dma.c | 55 ++++++++++++++----- .../net/ethernet/stmicro/stmmac/dwmac_dma.h | 17 ++++++ .../net/ethernet/stmicro/stmmac/dwmac_lib.c | 30 +++++----- 3 files changed, 74 insertions(+), 28 deletions(-)drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +2
-1@@ -12,7 +12,8 @@Author: Giuseppe Cavallaro <[email protected]> *******************************************************************************/ -#include <asm/io.h> +#include <linux/io.h> +#include "stmmac.h" #include "dwmac1000.h" #include "dwmac_dma.h" @@ -70,13 +71,16 @@ static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi)writel (value, ioaddr +DMA_AXI_BUS_MODE ); }
Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi) · line 76
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +3
-2-static void dwmac1000_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr, -struct stmmac_dma_cfg *dma_cfg,int atds) +static void dma_config (void __iomem *modeaddr,void __iomem *enaddr, +struct stmmac_dma_cfg *dma_cfg,u32 dma_intr_mask, +int atds)Please make sure the arguments are aligned with the function open parenthesis taking into account that tabs are of _8_ chars:
Documentation/process/coding-style.rst.
OK.
Quoted 54 lines
Quoted 35 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +18
-3{ -u32 value =readl (ioaddr +DMA_BUS_MODE ); +u32 value;int txpbl = dma_cfg->txpbl ?: dma_cfg->pbl;int rxpbl = dma_cfg->rxpbl ?: dma_cfg->pbl; + value =readl (modeaddr); +/* * Set the DMA PBL (Programmable Burst Length) mode. * @@ -104,10 +108,34 @@ static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr,if (dma_cfg->aal) value |=DMA_BUS_MODE_AAL ; -writel (value, ioaddr +DMA_BUS_MODE ); +writel (value, modeaddr); +writel (dma_intr_mask, enaddr); +} + +static void dwmac1000_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr, +struct stmmac_dma_cfg *dma_cfg,int atds) +{ +u32 dma_intr_mask;/* Mask interrupts by writing to CSR7 */ -writel (DMA_INTR_DEFAULT_MASK , ioaddr +DMA_INTR_ENA ); + dma_intr_mask =DMA_INTR_DEFAULT_MASK ; + +dma_config (ioaddr +DMA_BUS_MODE , ioaddr +DMA_INTR_ENA , + dma_cfg, dma_intr_mask, atds); +} + +static void dwmac1000_dma_init_channel(struct stmmac_priv *priv, void __iomem *ioaddr,drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr, · line 137
Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +10
-0+ struct stmmac_dma_cfg *dma_cfg, u32 chan) +{ +u32 dma_intr_mask; + +/* Mask interrupts by writing to CSR7 */ + dma_intr_mask =DMA_INTR_DEFAULT_MASK ; + +if (dma_cfg->multi_msi_en) + dma_config(ioaddr + DMA_CHAN_BUS_MODE(chan), + ioaddr + DMA_CHAN_INTR_ENA(chan), dma_cfg,Why so complicated?
stmmac_init_chan()is always supposed to be called in the same context asstmmac_dma_init()(stmmac_xdp_open()is wrong in not doing that). Seeing DW GMAC v3.x multi-channels feature is implemented as multiple sets of the same CSRs (except AV traffic control CSRs specific to channels 1 and higher which are left unused here anyway) you can just drop thestmmac_dma_ops.init()callback and convertdwmac1000_dma_init()to beingdwmac1000_dma_init_channel()with no significant modifications:
Quoted 6 lines
< you wouldn't need to have a separate
dma_config()method. < you wouldn't need to check for thedma_cfg->multi_msi_enflag state since thestmmac_init_chan()method is called for as many times as there are channels available (at least 1 channel always exists). < just add atds argument.
< just convert the method to using the chan-dependent CSR macros.
Yes, you are right.
Quoted 4 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr, · line 138
Quoted 2 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +1
-0+ dma_intr_mask, dma_cfg->multi_msi_en);^ +-------------------------------------------------+
Quoted 9 lines
This is wrong + ATDS flag means Alternative Descriptor Size. This flag enables the 8 dword DMA-descriptors size with some DMA-desc fields semantics changed (see
enh_desc.candnorm_desc.c). It's useful for PTP Timestamping, VLANs, AV feature, L3/L4 filtering, CSum offload Type 2 (if any of that available). It has nothing to do with the separate DMA IRQs. Just convert thestmmac_dma_ops.dma_init()callback to accepting the atds flag as an additional argument, use it here to activate the extended descriptor size and make sure the atds flag is passed to thestmmac_init_chan()method in the respective source code.
OK.
Quoted 65 lines
Quoted 65 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +7
-7} static void dwmac1000_dma_init_rx(struct stmmac_priv *priv,@@ -116,7 +144,7 @@ static void dwmac1000_dma_init_rx(struct stmmac_priv *priv, dma_addr_t dma_rx_phy, u32 chan) {/* RX descriptor base address list must be written into DMA CSR3 */ - writel(lower_32_bits(dma_rx_phy), ioaddr + DMA_RCV_BASE_ADDR); + writel(lower_32_bits(dma_rx_phy), ioaddr + DMA_CHAN_RCV_BASE_ADDR(chan)); } static void dwmac1000_dma_init_tx(struct stmmac_priv *priv,@@ -125,7 +153,7 @@ static void dwmac1000_dma_init_tx(struct stmmac_priv *priv, dma_addr_t dma_tx_phy, u32 chan) {/* TX descriptor base address list must be written into DMA CSR4 */ - writel(lower_32_bits(dma_tx_phy), ioaddr + DMA_TX_BASE_ADDR); + writel(lower_32_bits(dma_tx_phy), ioaddr + DMA_CHAN_TX_BASE_ADDR(chan)); }static u32 dwmac1000_configure_fc (u32 csr6,int rxfifosz)@@ -153,7 +181,7 @@ static void dwmac1000_dma_operation_mode_rx(struct stmmac_priv *priv, void __iomem *ioaddr, int mode, u32 channel, int fifosz, u8 qmode) { - u32 csr6 = readl(ioaddr + DMA_CONTROL); + u32 csr6 = readl(ioaddr + DMA_CHAN_CONTROL(channel));if (mode ==SF_DMA_MODE ) {pr_debug ("GMAC: enable RX store and forward mode\n" );@@ -175,14 +203,14 @@ static void dwmac1000_dma_operation_mode_rx(struct stmmac_priv *priv,/* Configure flow control based on rx fifo size */ csr6 =dwmac1000_configure_fc (csr6, fifosz); -writel (csr6, ioaddr +DMA_CONTROL ); +writel (csr6, ioaddr +DMA_CHAN_CONTROL (channel)); }static void dwmac1000_dma_operation_mode_tx (struct stmmac_priv *priv,void __iomem *ioaddr,int mode,u32 channel,int fifosz,u8 qmode) { -u32 csr6 =readl (ioaddr +DMA_CONTROL ); +u32 csr6 =readl (ioaddr +DMA_CHAN_CONTROL (channel));if (mode ==SF_DMA_MODE ) {pr_debug ("GMAC: enable TX store and forward mode\n" );@@ -209,7 +237,7 @@ static void dwmac1000_dma_operation_mode_tx(struct stmmac_priv *priv, csr6 |=DMA_CONTROL_TTC_256 ; } -writel (csr6, ioaddr +DMA_CONTROL ); +writel (csr6, ioaddr +DMA_CHAN_CONTROL (channel)); } static void dwmac1000_dump_dma_regs(struct stmmac_priv *priv,@@ -271,12 +299,13 @@ static int dwmac1000_get_hw_feature(void __iomem *ioaddr,static void dwmac1000_rx_watchdog (struct stmmac_priv *priv,void __iomem *ioaddr,u32 riwt,u32 queue) { -writel (riwt, ioaddr +DMA_RX_WATCHDOG ); +writel (riwt, ioaddr +DMA_CHAN_RX_WATCHDOG (queue)); }
Quoted 4 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static int dwmac1000_get_hw_feature(void __iomem *ioaddr, · line 307
Quoted 3 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +0
-0const struct stmmac_dma_ops dwmac1000_dma_ops = { .reset = dwmac_dma_reset, .init = dwmac1000_dma_init,This could be dropped. See my comment above.
OK, I've tried this and it works.
Quoted 13 lines
Quoted 13 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +1
-0+ .init_chan = dwmac1000_dma_init_channel, .init_rx_chan = dwmac1000_dma_init_rx, .init_tx_chan = dwmac1000_dma_init_tx, .axi = dwmac1000_dma_axi,drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +0
-0@@ -148,6 +148,9 @@DMA_STATUS_TI | \ DMA_STATUS_MSK_COMMON)
Quoted 2 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h line 151
Quoted 1 line
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +1
-0+/* Following DMA defines are chanels oriented */ s/chanels/channels
OK!
Quoted 4 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h line 152
Quoted 2 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +1
-0+#define DMA_CHAN_OFFSET 0x100
DMA_CHAN_BASE_OFFSET? to be looking the same as in DW QoS Eth GMAC v4.x/v5.x (dwmac4_dma.h).
OK
Quoted 117 lines
Quoted 117 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +15
-0+#define NUM_DWMAC100_DMA_REGS 9#define NUM_DWMAC1000_DMA_REGS 23#define NUM_DWMAC4_DMA_REGS 27@@ -170,4 +173,18 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr, struct stmmac_extra_stats *x, u32 chan, u32 dir);int dwmac_dma_reset (void __iomem *ioaddr); +static inline u32 dma_chan_base_addr (u32 base,u32 chan) +{ +return base + chan *DMA_CHAN_OFFSET ; +} + +#define DMA_CHAN_XMT_POLL_DEMAND (chan) dma_chan_base_addr(DMA_XMT_POLL_DEMAND, chan) +#define DMA_CHAN_INTR_ENA (chan) dma_chan_base_addr(DMA_INTR_ENA, chan) +#define DMA_CHAN_CONTROL (chan) dma_chan_base_addr(DMA_CONTROL, chan) +#define DMA_CHAN_STATUS (chan) dma_chan_base_addr(DMA_STATUS, chan) +#define DMA_CHAN_BUS_MODE (chan) dma_chan_base_addr(DMA_BUS_MODE, chan) +#define DMA_CHAN_RCV_BASE_ADDR (chan) dma_chan_base_addr(DMA_RCV_BASE_ADDR, chan) +#define DMA_CHAN_TX_BASE_ADDR (chan) dma_chan_base_addr(DMA_TX_BASE_ADDR, chan) +#define DMA_CHAN_RX_WATCHDOG (chan) dma_chan_base_addr(DMA_RX_WATCHDOG, chan) +#endif /* __DWMAC_DMA_H__ */ drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +14
-14@@ -31,63 +31,63 @@ int dwmac_dma_reset(void __iomem *ioaddr)void dwmac_enable_dma_transmission (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -writel (1 , ioaddr +DMA_XMT_POLL_DEMAND ); +writel (1 , ioaddr +DMA_CHAN_XMT_POLL_DEMAND (chan)); }void dwmac_enable_dma_irq (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan,bool rx,bool tx) { -u32 value =readl (ioaddr +DMA_INTR_ENA ); +u32 value =readl (ioaddr +DMA_CHAN_INTR_ENA (chan));if (rx) value |=DMA_INTR_DEFAULT_RX ;if (tx) value |=DMA_INTR_DEFAULT_TX ; -writel (value, ioaddr +DMA_INTR_ENA ); +writel (value, ioaddr +DMA_CHAN_INTR_ENA (chan)); }void dwmac_disable_dma_irq (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan,bool rx,bool tx) { -u32 value =readl (ioaddr +DMA_INTR_ENA ); +u32 value =readl (ioaddr +DMA_CHAN_INTR_ENA (chan));if (rx) value &= ~DMA_INTR_DEFAULT_RX ;if (tx) value &= ~DMA_INTR_DEFAULT_TX ; -writel (value, ioaddr +DMA_INTR_ENA ); +writel (value, ioaddr +DMA_CHAN_INTR_ENA (chan)); }void dwmac_dma_start_tx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value |=DMA_CONTROL_ST ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }void dwmac_dma_stop_tx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value &= ~DMA_CONTROL_ST ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }void dwmac_dma_start_rx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value |=DMA_CONTROL_SR ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }void dwmac_dma_stop_rx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value &= ~DMA_CONTROL_SR ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }#ifdef DWMAC_DMA_DEBUG @@ -167,7 +167,7 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,struct stmmac_txq_stats *txq_stats = &priv->xstats.txq_stats[chan];int ret =0 ;/* read the status register (CSR5) */ -u32 intr_status =readl (ioaddr +DMA_STATUS ); +u32 intr_status =readl (ioaddr +DMA_CHAN_STATUS (chan));#ifdef DWMAC_DMA_DEBUG /* Enable it to monitor DMA rx/tx status in case of critical problems */ @@ -237,7 +237,7 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,pr_warn ("%s: unexpected status %08x\n" , __func__, intr_status);
Quoted 4 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr, · line 240
Quoted 3 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +1
-1/* Clear the interrupt by writing a logic 1 to the CSR5[15-0] */ -writel ((intr_status &0x1ffff ), ioaddr +DMA_STATUS ); +writel ((intr_status &0x7ffff ), ioaddr +DMA_CHAN_STATUS (chan));Em, please explain the mask change. Bits CSR5[17:28] are defined as RO
I'm not sure I can explain it, but it goes something like this:
We moved these bits up because we split the reception and transmission of interrupts.
28 Reserved
27:25 EB
24:22 TS
21:19 RS
18 NTIS
Quoted 2 lines
on a normal DW GMAC. Anyway it seems like the mask changes belongs to the patch 5/9.
Yes, I will try.
Quoted 5 lines
Except the last comment, AFAICS this patch provides a generic DW GMAC v3.x multi-channel support. Despite of several issues noted above the change in general looks very good.
Thanks, the next version of this patch will only have changes related to dma_chan_base_addr.
* dwmac1000_dma_init will be restored.
* dwmac1000_dma_init_channel() will be moved to dwmac-loongson.c.
Thanks for your review!
Thanks,
Yanteng
Quoted 9 lines
-Serge(y)
Quoted 6 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +0
-0return ret; }Signature · 1 line
2.31.4
Re: [PATCH net-next v7 4/9] net: stmmac: Add multi-channel supports
Hi Yanteng
Quoted 308 lines · Yanteng Si
Quoted 32 lines · Serge Semin
Quoted 31 lines · Yanteng Si
Loongson platforms use a DWGMAC which supports multi-channel.
Added
dwmac1000_dma_init_channel()andinit_chan(), factor out all the channel-specific setups fromdwmac1000_dma_init()to the new functiondma_config(), then distinguish dma initialization and multi-channel initialization through different parameters.Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- .../ethernet/stmicro/stmmac/dwmac1000_dma.c | 55 ++++++++++++++----- .../net/ethernet/stmicro/stmmac/dwmac_dma.h | 17 ++++++ .../net/ethernet/stmicro/stmmac/dwmac_lib.c | 30 +++++----- 3 files changed, 74 insertions(+), 28 deletions(-)drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +2
-1@@ -12,7 +12,8 @@Author: Giuseppe Cavallaro <[email protected]> *******************************************************************************/ -#include <asm/io.h> +#include <linux/io.h> +#include "stmmac.h" #include "dwmac1000.h" #include "dwmac_dma.h" @@ -70,13 +71,16 @@ static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi)writel (value, ioaddr +DMA_AXI_BUS_MODE ); }Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi) · line 76
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +3
-2-static void dwmac1000_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr, -struct stmmac_dma_cfg *dma_cfg,int atds) +static void dma_config (void __iomem *modeaddr,void __iomem *enaddr, +struct stmmac_dma_cfg *dma_cfg,u32 dma_intr_mask, +int atds)Please make sure the arguments are aligned with the function open parenthesis taking into account that tabs are of _8_ chars:
Documentation/process/coding-style.rst.OK.
Quoted 51 lines
Quoted 32 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +18
-3{ -u32 value =readl (ioaddr +DMA_BUS_MODE ); +u32 value;int txpbl = dma_cfg->txpbl ?: dma_cfg->pbl;int rxpbl = dma_cfg->rxpbl ?: dma_cfg->pbl; + value =readl (modeaddr); +/* * Set the DMA PBL (Programmable Burst Length) mode. * @@ -104,10 +108,34 @@ static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr,if (dma_cfg->aal) value |=DMA_BUS_MODE_AAL ; -writel (value, ioaddr +DMA_BUS_MODE ); +writel (value, modeaddr); +writel (dma_intr_mask, enaddr); +} + +static void dwmac1000_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr, +struct stmmac_dma_cfg *dma_cfg,int atds) +{ +u32 dma_intr_mask;/* Mask interrupts by writing to CSR7 */ -writel (DMA_INTR_DEFAULT_MASK , ioaddr +DMA_INTR_ENA ); + dma_intr_mask =DMA_INTR_DEFAULT_MASK ; + +dma_config (ioaddr +DMA_BUS_MODE , ioaddr +DMA_INTR_ENA , + dma_cfg, dma_intr_mask, atds); +} + +static void dwmac1000_dma_init_channel(struct stmmac_priv *priv, void __iomem *ioaddr,drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr, · line 135
Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +10
-0+ struct stmmac_dma_cfg *dma_cfg, u32 chan) +{ +u32 dma_intr_mask; + +/* Mask interrupts by writing to CSR7 */ + dma_intr_mask =DMA_INTR_DEFAULT_MASK ; + +if (dma_cfg->multi_msi_en) + dma_config(ioaddr + DMA_CHAN_BUS_MODE(chan), + ioaddr + DMA_CHAN_INTR_ENA(chan), dma_cfg,Why so complicated?
stmmac_init_chan()is always supposed to be called in the same context asstmmac_dma_init()(stmmac_xdp_open()is wrong in not doing that). Seeing DW GMAC v3.x multi-channels feature is implemented as multiple sets of the same CSRs (except AV traffic control CSRs specific to channels 1 and higher which are left unused here anyway) you can just drop thestmmac_dma_ops.init()callback and convertdwmac1000_dma_init()to beingdwmac1000_dma_init_channel()with no significant modifications:Quoted 6 lines
< you wouldn't need to have a separate
dma_config()method. < you wouldn't need to check for thedma_cfg->multi_msi_enflag state since thestmmac_init_chan()method is called for as many times as there are channels available (at least 1 channel always exists). < just add atds argument.
< just convert the method to using the chan-dependent CSR macros.Yes, you are right.
Quoted 4 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr, · line 138
Quoted 2 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +1
-0+ dma_intr_mask, dma_cfg->multi_msi_en);^ +-------------------------------------------------+Quoted 9 lines
This is wrong + ATDS flag means Alternative Descriptor Size. This flag enables the 8 dword DMA-descriptors size with some DMA-desc fields semantics changed (see
enh_desc.candnorm_desc.c). It's useful for PTP Timestamping, VLANs, AV feature, L3/L4 filtering, CSum offload Type 2 (if any of that available). It has nothing to do with the separate DMA IRQs. Just convert thestmmac_dma_ops.dma_init()callback to accepting the atds flag as an additional argument, use it here to activate the extended descriptor size and make sure the atds flag is passed to thestmmac_init_chan()method in the respective source code.OK.
Quoted 51 lines
Quoted 51 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +6
-6} static void dwmac1000_dma_init_rx(struct stmmac_priv *priv,@@ -116,7 +144,7 @@ static void dwmac1000_dma_init_rx(struct stmmac_priv *priv, dma_addr_t dma_rx_phy, u32 chan) {/* RX descriptor base address list must be written into DMA CSR3 */ - writel(lower_32_bits(dma_rx_phy), ioaddr + DMA_RCV_BASE_ADDR); + writel(lower_32_bits(dma_rx_phy), ioaddr + DMA_CHAN_RCV_BASE_ADDR(chan)); } static void dwmac1000_dma_init_tx(struct stmmac_priv *priv,@@ -125,7 +153,7 @@ static void dwmac1000_dma_init_tx(struct stmmac_priv *priv, dma_addr_t dma_tx_phy, u32 chan) {/* TX descriptor base address list must be written into DMA CSR4 */ - writel(lower_32_bits(dma_tx_phy), ioaddr + DMA_TX_BASE_ADDR); + writel(lower_32_bits(dma_tx_phy), ioaddr + DMA_CHAN_TX_BASE_ADDR(chan)); }static u32 dwmac1000_configure_fc (u32 csr6,int rxfifosz)@@ -153,7 +181,7 @@ static void dwmac1000_dma_operation_mode_rx(struct stmmac_priv *priv, void __iomem *ioaddr, int mode, u32 channel, int fifosz, u8 qmode) { - u32 csr6 = readl(ioaddr + DMA_CONTROL); + u32 csr6 = readl(ioaddr + DMA_CHAN_CONTROL(channel));if (mode ==SF_DMA_MODE ) {pr_debug ("GMAC: enable RX store and forward mode\n" );@@ -175,14 +203,14 @@ static void dwmac1000_dma_operation_mode_rx(struct stmmac_priv *priv,/* Configure flow control based on rx fifo size */ csr6 =dwmac1000_configure_fc (csr6, fifosz); -writel (csr6, ioaddr +DMA_CONTROL ); +writel (csr6, ioaddr +DMA_CHAN_CONTROL (channel)); }static void dwmac1000_dma_operation_mode_tx (struct stmmac_priv *priv,void __iomem *ioaddr,int mode,u32 channel,int fifosz,u8 qmode) { -u32 csr6 =readl (ioaddr +DMA_CONTROL ); +u32 csr6 =readl (ioaddr +DMA_CHAN_CONTROL (channel));if (mode ==SF_DMA_MODE ) {pr_debug ("GMAC: enable TX store and forward mode\n" );@@ -209,7 +237,7 @@ static void dwmac1000_dma_operation_mode_tx(struct stmmac_priv *priv, csr6 |=DMA_CONTROL_TTC_256 ; } -writel (csr6, ioaddr +DMA_CONTROL ); +writel (csr6, ioaddr +DMA_CHAN_CONTROL (channel)); } static void dwmac1000_dump_dma_regs(struct stmmac_priv *priv,@@ -271,12 +299,13 @@ static int dwmac1000_get_hw_feature(void __iomem *ioaddr,static void dwmac1000_rx_watchdog (struct stmmac_priv *priv,void __iomem *ioaddr,u32 riwt,u32 queue)Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static int dwmac1000_get_hw_feature(void __iomem *ioaddr, · line 307
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +1
-1{ -writel (riwt, ioaddr +DMA_RX_WATCHDOG ); +writel (riwt, ioaddr +DMA_CHAN_RX_WATCHDOG (queue)); }const struct stmmac_dma_ops dwmac1000_dma_ops = { .reset = dwmac_dma_reset, .init = dwmac1000_dma_init,This could be dropped. See my comment above.
OK, I've tried this and it works.
Quoted 14 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h line 150
Quoted 13 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +1
-0+ .init_chan = dwmac1000_dma_init_channel, .init_rx_chan = dwmac1000_dma_init_rx, .init_tx_chan = dwmac1000_dma_init_tx, .axi = dwmac1000_dma_axi,drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +1
-0@@ -148,6 +148,9 @@DMA_STATUS_TI | \ DMA_STATUS_MSK_COMMON) +/* Following DMA defines are chanels oriented */ s/chanels/channels
OK!
Quoted 4 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h line 152
Quoted 2 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +1
-0+#define DMA_CHAN_OFFSET 0x100
DMA_CHAN_BASE_OFFSET? to be looking the same as in DW QoS Eth GMAC v4.x/v5.x (dwmac4_dma.h).OK
Quoted 105 lines
Quoted 104 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +15
-0+#define NUM_DWMAC100_DMA_REGS 9#define NUM_DWMAC1000_DMA_REGS 23#define NUM_DWMAC4_DMA_REGS 27@@ -170,4 +173,18 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr, struct stmmac_extra_stats *x, u32 chan, u32 dir);int dwmac_dma_reset (void __iomem *ioaddr); +static inline u32 dma_chan_base_addr (u32 base,u32 chan) +{ +return base + chan *DMA_CHAN_OFFSET ; +} + +#define DMA_CHAN_XMT_POLL_DEMAND (chan) dma_chan_base_addr(DMA_XMT_POLL_DEMAND, chan) +#define DMA_CHAN_INTR_ENA (chan) dma_chan_base_addr(DMA_INTR_ENA, chan) +#define DMA_CHAN_CONTROL (chan) dma_chan_base_addr(DMA_CONTROL, chan) +#define DMA_CHAN_STATUS (chan) dma_chan_base_addr(DMA_STATUS, chan) +#define DMA_CHAN_BUS_MODE (chan) dma_chan_base_addr(DMA_BUS_MODE, chan) +#define DMA_CHAN_RCV_BASE_ADDR (chan) dma_chan_base_addr(DMA_RCV_BASE_ADDR, chan) +#define DMA_CHAN_TX_BASE_ADDR (chan) dma_chan_base_addr(DMA_TX_BASE_ADDR, chan) +#define DMA_CHAN_RX_WATCHDOG (chan) dma_chan_base_addr(DMA_RX_WATCHDOG, chan) +#endif /* __DWMAC_DMA_H__ */ drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +14
-14@@ -31,63 +31,63 @@ int dwmac_dma_reset(void __iomem *ioaddr)void dwmac_enable_dma_transmission (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -writel (1 , ioaddr +DMA_XMT_POLL_DEMAND ); +writel (1 , ioaddr +DMA_CHAN_XMT_POLL_DEMAND (chan)); }void dwmac_enable_dma_irq (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan,bool rx,bool tx) { -u32 value =readl (ioaddr +DMA_INTR_ENA ); +u32 value =readl (ioaddr +DMA_CHAN_INTR_ENA (chan));if (rx) value |=DMA_INTR_DEFAULT_RX ;if (tx) value |=DMA_INTR_DEFAULT_TX ; -writel (value, ioaddr +DMA_INTR_ENA ); +writel (value, ioaddr +DMA_CHAN_INTR_ENA (chan)); }void dwmac_disable_dma_irq (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan,bool rx,bool tx) { -u32 value =readl (ioaddr +DMA_INTR_ENA ); +u32 value =readl (ioaddr +DMA_CHAN_INTR_ENA (chan));if (rx) value &= ~DMA_INTR_DEFAULT_RX ;if (tx) value &= ~DMA_INTR_DEFAULT_TX ; -writel (value, ioaddr +DMA_INTR_ENA ); +writel (value, ioaddr +DMA_CHAN_INTR_ENA (chan)); }void dwmac_dma_start_tx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value |=DMA_CONTROL_ST ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }void dwmac_dma_stop_tx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value &= ~DMA_CONTROL_ST ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }void dwmac_dma_start_rx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value |=DMA_CONTROL_SR ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }void dwmac_dma_stop_rx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value &= ~DMA_CONTROL_SR ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }#ifdef DWMAC_DMA_DEBUG @@ -167,7 +167,7 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,struct stmmac_txq_stats *txq_stats = &priv->xstats.txq_stats[chan];int ret =0 ;/* read the status register (CSR5) */ -u32 intr_status =readl (ioaddr +DMA_STATUS ); +u32 intr_status =readl (ioaddr +DMA_CHAN_STATUS (chan));#ifdef DWMAC_DMA_DEBUG /* Enable it to monitor DMA rx/tx status in case of critical problems */ @@ -237,7 +237,7 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,pr_warn ("%s: unexpected status %08x\n" , __func__, intr_status);/* Clear the interrupt by writing a logic 1 to the CSR5[15-0] */ Quoted 3 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr, · line 240
Quoted 2 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +1
-1-writel ((intr_status &0x1ffff ), ioaddr +DMA_STATUS ); +writel ((intr_status &0x7ffff ), ioaddr +DMA_CHAN_STATUS (chan));Em, please explain the mask change. Bits CSR5[17:28] are defined as RO
I'm not sure I can explain it, but it goes something like this:
Quoted 8 lines
We moved these bits up because we split the reception and transmission of interrupts.
28 Reserved
27:25 EB
24:22 TS
21:19 RS
18 NTIS
I see. Thanks for clarification. Let's postpone the IRQ mask discussion for the next review round.
Quoted 12 lines
Quoted 4 lines
on a normal DW GMAC. Anyway it seems like the mask changes belongs to the patch 5/9.
Yes, I will try.
Quoted 5 lines
Except the last comment, AFAICS this patch provides a generic DW GMAC v3.x multi-channel support. Despite of several issues noted above the change in general looks very good.
Quoted 7 lines
Thanks, the next version of this patch will only have changes related to
dma_chan_base_addr.*
dwmac1000_dma_initwill be restored.*
dwmac1000_dma_init_channel()will be moved todwmac-loongson.c.
No. That's not what I meant. I said that this patch looks _generic_ enough to be applied (with my notes taken into account) in the common dwmac1000_dma.c code! It provides useful multi-DMA-channels support in a way it's implemented by the _generic_ DW GMAC v3.x IP-core. From that perspective the change will be useful for all users which DW GMACs support the multi-channels feature. Please fix the patch based on my notes and repost it as a part of your series. We'll figure out what to do with the IRQ mask on the next review round.
-Serge(y)
Quoted 18 lines
Thanks for your review!
Thanks,
Yanteng
Quoted 8 lines
-Serge(y)
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +0
-0return ret; }Signature · 1 line
2.31.4
Re: [PATCH net-next v7 4/9] net: stmmac: Add multi-channel supports
Quoted 304 lines · Serge Semin
Hi Yanteng
Quoted 301 lines · Yanteng Si
Quoted 32 lines · Serge Semin
Quoted 31 lines · Yanteng Si
Loongson platforms use a DWGMAC which supports multi-channel.
Added
dwmac1000_dma_init_channel()andinit_chan(), factor out all the channel-specific setups fromdwmac1000_dma_init()to the new functiondma_config(), then distinguish dma initialization and multi-channel initialization through different parameters.Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- .../ethernet/stmicro/stmmac/dwmac1000_dma.c | 55 ++++++++++++++----- .../net/ethernet/stmicro/stmmac/dwmac_dma.h | 17 ++++++ .../net/ethernet/stmicro/stmmac/dwmac_lib.c | 30 +++++----- 3 files changed, 74 insertions(+), 28 deletions(-)drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +2
-1@@ -12,7 +12,8 @@Author: Giuseppe Cavallaro <[email protected]> *******************************************************************************/ -#include <asm/io.h> +#include <linux/io.h> +#include "stmmac.h" #include "dwmac1000.h" #include "dwmac_dma.h" @@ -70,13 +71,16 @@ static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi)writel (value, ioaddr +DMA_AXI_BUS_MODE ); }Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi) · line 76
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +3
-2-static void dwmac1000_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr, -struct stmmac_dma_cfg *dma_cfg,int atds) +static void dma_config (void __iomem *modeaddr,void __iomem *enaddr, +struct stmmac_dma_cfg *dma_cfg,u32 dma_intr_mask, +int atds)Please make sure the arguments are aligned with the function open parenthesis taking into account that tabs are of _8_ chars:
Documentation/process/coding-style.rst.OK.
Quoted 50 lines
Quoted 31 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +18
-3{ -u32 value =readl (ioaddr +DMA_BUS_MODE ); +u32 value;int txpbl = dma_cfg->txpbl ?: dma_cfg->pbl;int rxpbl = dma_cfg->rxpbl ?: dma_cfg->pbl; + value =readl (modeaddr); +/* * Set the DMA PBL (Programmable Burst Length) mode. * @@ -104,10 +108,34 @@ static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr,if (dma_cfg->aal) value |=DMA_BUS_MODE_AAL ; -writel (value, ioaddr +DMA_BUS_MODE ); +writel (value, modeaddr); +writel (dma_intr_mask, enaddr); +} + +static void dwmac1000_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr, +struct stmmac_dma_cfg *dma_cfg,int atds) +{ +u32 dma_intr_mask;/* Mask interrupts by writing to CSR7 */ -writel (DMA_INTR_DEFAULT_MASK , ioaddr +DMA_INTR_ENA ); + dma_intr_mask =DMA_INTR_DEFAULT_MASK ; + +dma_config (ioaddr +DMA_BUS_MODE , ioaddr +DMA_INTR_ENA , + dma_cfg, dma_intr_mask, atds); +} + +static void dwmac1000_dma_init_channel(struct stmmac_priv *priv, void __iomem *ioaddr,drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr, · line 135
Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +10
-0+ struct stmmac_dma_cfg *dma_cfg, u32 chan) +{ +u32 dma_intr_mask; + +/* Mask interrupts by writing to CSR7 */ + dma_intr_mask =DMA_INTR_DEFAULT_MASK ; + +if (dma_cfg->multi_msi_en) + dma_config(ioaddr + DMA_CHAN_BUS_MODE(chan), + ioaddr + DMA_CHAN_INTR_ENA(chan), dma_cfg,Why so complicated?
stmmac_init_chan()is always supposed to be called in the same context asstmmac_dma_init()(stmmac_xdp_open()is wrong in not doing that). Seeing DW GMAC v3.x multi-channels feature is implemented as multiple sets of the same CSRs (except AV traffic control CSRs specific to channels 1 and higher which are left unused here anyway) you can just drop thestmmac_dma_ops.init()callback and convertdwmac1000_dma_init()to beingdwmac1000_dma_init_channel()with no significant modifications:Quoted 6 lines
< you wouldn't need to have a separate
dma_config()method. < you wouldn't need to check for thedma_cfg->multi_msi_enflag state since thestmmac_init_chan()method is called for as many times as there are channels available (at least 1 channel always exists). < just add atds argument.
< just convert the method to using the chan-dependent CSR macros.Yes, you are right.
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr, · line 138
Quoted 1 line
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +1
-0+ dma_intr_mask, dma_cfg->multi_msi_en);^ +-------------------------------------------------+This is wrong + ATDS flag means Alternative Descriptor Size. This flag enables the 8 dword DMA-descriptors size with some DMA-desc fields semantics changed (see
enh_desc.candnorm_desc.c). It's useful for PTP Timestamping, VLANs, AV feature, L3/L4 filtering, CSum offload Type 2 (if any of that available). It has nothing to do with the separate DMA IRQs. Just convert thestmmac_dma_ops.dma_init()callback to accepting the atds flag as an additional argument, use it here to activate the extended descriptor size and make sure the atds flag is passed to thestmmac_init_chan()method in the respective source code.OK.
Quoted 50 lines
Quoted 50 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +6
-6} static void dwmac1000_dma_init_rx(struct stmmac_priv *priv,@@ -116,7 +144,7 @@ static void dwmac1000_dma_init_rx(struct stmmac_priv *priv, dma_addr_t dma_rx_phy, u32 chan) {/* RX descriptor base address list must be written into DMA CSR3 */ - writel(lower_32_bits(dma_rx_phy), ioaddr + DMA_RCV_BASE_ADDR); + writel(lower_32_bits(dma_rx_phy), ioaddr + DMA_CHAN_RCV_BASE_ADDR(chan)); } static void dwmac1000_dma_init_tx(struct stmmac_priv *priv,@@ -125,7 +153,7 @@ static void dwmac1000_dma_init_tx(struct stmmac_priv *priv, dma_addr_t dma_tx_phy, u32 chan) {/* TX descriptor base address list must be written into DMA CSR4 */ - writel(lower_32_bits(dma_tx_phy), ioaddr + DMA_TX_BASE_ADDR); + writel(lower_32_bits(dma_tx_phy), ioaddr + DMA_CHAN_TX_BASE_ADDR(chan)); }static u32 dwmac1000_configure_fc (u32 csr6,int rxfifosz)@@ -153,7 +181,7 @@ static void dwmac1000_dma_operation_mode_rx(struct stmmac_priv *priv, void __iomem *ioaddr, int mode, u32 channel, int fifosz, u8 qmode) { - u32 csr6 = readl(ioaddr + DMA_CONTROL); + u32 csr6 = readl(ioaddr + DMA_CHAN_CONTROL(channel));if (mode ==SF_DMA_MODE ) {pr_debug ("GMAC: enable RX store and forward mode\n" );@@ -175,14 +203,14 @@ static void dwmac1000_dma_operation_mode_rx(struct stmmac_priv *priv,/* Configure flow control based on rx fifo size */ csr6 =dwmac1000_configure_fc (csr6, fifosz); -writel (csr6, ioaddr +DMA_CONTROL ); +writel (csr6, ioaddr +DMA_CHAN_CONTROL (channel)); }static void dwmac1000_dma_operation_mode_tx (struct stmmac_priv *priv,void __iomem *ioaddr,int mode,u32 channel,int fifosz,u8 qmode) { -u32 csr6 =readl (ioaddr +DMA_CONTROL ); +u32 csr6 =readl (ioaddr +DMA_CHAN_CONTROL (channel));if (mode ==SF_DMA_MODE ) {pr_debug ("GMAC: enable TX store and forward mode\n" );@@ -209,7 +237,7 @@ static void dwmac1000_dma_operation_mode_tx(struct stmmac_priv *priv, csr6 |=DMA_CONTROL_TTC_256 ; } -writel (csr6, ioaddr +DMA_CONTROL ); +writel (csr6, ioaddr +DMA_CHAN_CONTROL (channel)); } static void dwmac1000_dump_dma_regs(struct stmmac_priv *priv,@@ -271,12 +299,13 @@ static int dwmac1000_get_hw_feature(void __iomem *ioaddr,static void dwmac1000_rx_watchdog (struct stmmac_priv *priv,void __iomem *ioaddr,u32 riwt,u32 queue)Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static int dwmac1000_get_hw_feature(void __iomem *ioaddr, · line 307
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +1
-1{ -writel (riwt, ioaddr +DMA_RX_WATCHDOG ); +writel (riwt, ioaddr +DMA_CHAN_RX_WATCHDOG (queue)); }const struct stmmac_dma_ops dwmac1000_dma_ops = { .reset = dwmac_dma_reset, .init = dwmac1000_dma_init,This could be dropped. See my comment above.
OK, I've tried this and it works.
Quoted 5 lines
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +1
-0+ .init_chan = dwmac1000_dma_init_channel, .init_rx_chan = dwmac1000_dma_init_rx, .init_tx_chan = dwmac1000_dma_init_tx, .axi = dwmac1000_dma_axi,drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +0
-0Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h line 150
Quoted 7 lines
index
e7aef136824b..395d5e4c3922100644drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +1
-0@@ -148,6 +148,9 @@DMA_STATUS_TI | \ DMA_STATUS_MSK_COMMON) +/* Following DMA defines are chanels oriented */ s/chanels/channels
OK!
Quoted 3 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h line 152
Quoted 1 line
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +1
-0+#define DMA_CHAN_OFFSET 0x100
DMA_CHAN_BASE_OFFSET? to be looking the same as in DW QoS Eth GMAC v4.x/v5.x (dwmac4_dma.h).OK
Quoted 98 lines
Quoted 98 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +15
-0+#define NUM_DWMAC100_DMA_REGS 9#define NUM_DWMAC1000_DMA_REGS 23#define NUM_DWMAC4_DMA_REGS 27@@ -170,4 +173,18 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr, struct stmmac_extra_stats *x, u32 chan, u32 dir);int dwmac_dma_reset (void __iomem *ioaddr); +static inline u32 dma_chan_base_addr (u32 base,u32 chan) +{ +return base + chan *DMA_CHAN_OFFSET ; +} + +#define DMA_CHAN_XMT_POLL_DEMAND (chan) dma_chan_base_addr(DMA_XMT_POLL_DEMAND, chan) +#define DMA_CHAN_INTR_ENA (chan) dma_chan_base_addr(DMA_INTR_ENA, chan) +#define DMA_CHAN_CONTROL (chan) dma_chan_base_addr(DMA_CONTROL, chan) +#define DMA_CHAN_STATUS (chan) dma_chan_base_addr(DMA_STATUS, chan) +#define DMA_CHAN_BUS_MODE (chan) dma_chan_base_addr(DMA_BUS_MODE, chan) +#define DMA_CHAN_RCV_BASE_ADDR (chan) dma_chan_base_addr(DMA_RCV_BASE_ADDR, chan) +#define DMA_CHAN_TX_BASE_ADDR (chan) dma_chan_base_addr(DMA_TX_BASE_ADDR, chan) +#define DMA_CHAN_RX_WATCHDOG (chan) dma_chan_base_addr(DMA_RX_WATCHDOG, chan) +#endif /* __DWMAC_DMA_H__ */ drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +14
-14@@ -31,63 +31,63 @@ int dwmac_dma_reset(void __iomem *ioaddr)void dwmac_enable_dma_transmission (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -writel (1 , ioaddr +DMA_XMT_POLL_DEMAND ); +writel (1 , ioaddr +DMA_CHAN_XMT_POLL_DEMAND (chan)); }void dwmac_enable_dma_irq (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan,bool rx,bool tx) { -u32 value =readl (ioaddr +DMA_INTR_ENA ); +u32 value =readl (ioaddr +DMA_CHAN_INTR_ENA (chan));if (rx) value |=DMA_INTR_DEFAULT_RX ;if (tx) value |=DMA_INTR_DEFAULT_TX ; -writel (value, ioaddr +DMA_INTR_ENA ); +writel (value, ioaddr +DMA_CHAN_INTR_ENA (chan)); }void dwmac_disable_dma_irq (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan,bool rx,bool tx) { -u32 value =readl (ioaddr +DMA_INTR_ENA ); +u32 value =readl (ioaddr +DMA_CHAN_INTR_ENA (chan));if (rx) value &= ~DMA_INTR_DEFAULT_RX ;if (tx) value &= ~DMA_INTR_DEFAULT_TX ; -writel (value, ioaddr +DMA_INTR_ENA ); +writel (value, ioaddr +DMA_CHAN_INTR_ENA (chan)); }void dwmac_dma_start_tx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value |=DMA_CONTROL_ST ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }void dwmac_dma_stop_tx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value &= ~DMA_CONTROL_ST ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }void dwmac_dma_start_rx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value |=DMA_CONTROL_SR ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }void dwmac_dma_stop_rx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value &= ~DMA_CONTROL_SR ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }#ifdef DWMAC_DMA_DEBUG @@ -167,7 +167,7 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,struct stmmac_txq_stats *txq_stats = &priv->xstats.txq_stats[chan];int ret =0 ;/* read the status register (CSR5) */ -u32 intr_status =readl (ioaddr +DMA_STATUS ); +u32 intr_status =readl (ioaddr +DMA_CHAN_STATUS (chan));Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr, · line 239
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +1
-1#ifdef DWMAC_DMA_DEBUG /* Enable it to monitor DMA rx/tx status in case of critical problems */ @@ -237,7 +237,7 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,pr_warn ("%s: unexpected status %08x\n" , __func__, intr_status);/* Clear the interrupt by writing a logic 1 to the CSR5[15-0] */ -writel ((intr_status &0x1ffff ), ioaddr +DMA_STATUS ); +writel ((intr_status &0x7ffff ), ioaddr +DMA_CHAN_STATUS (chan));Em, please explain the mask change. Bits CSR5[17:28] are defined as RO
I'm not sure I can explain it, but it goes something like this:
We moved these bits up because we split the reception and transmission of interrupts.
Quoted 7 lines
Quoted 5 lines
28 Reserved
27:25 EB
24:22 TS
21:19 RS
18 NTISI see. Thanks for clarification. Let's postpone the IRQ mask discussion for the next review round.
OK.
Quoted 16 lines
Quoted 9 lines
Quoted 4 lines
on a normal DW GMAC. Anyway it seems like the mask changes belongs to the patch 5/9.
Yes, I will try.
Quoted 4 lines
Except the last comment, AFAICS this patch provides a generic DW GMAC v3.x multi-channel support. Despite of several issues noted above the change in general looks very good.
Quoted 7 lines
Thanks, the next version of this patch will only have changes related to
dma_chan_base_addr.*
dwmac1000_dma_initwill be restored.*
dwmac1000_dma_init_channel()will be moved todwmac-loongson.c.
Quoted 8 lines
No. That's not what I meant. I said that this patch looks _generic_ enough to be applied (with my notes taken into account) in the common
dwmac1000_dma.ccode! It provides useful multi-DMA-channels support in a way it's implemented by the _generic_ DW GMAC v3.x IP-core. From that perspective the change will be useful for all users which DW GMACs support the multi-channels feature. Please fix the patch based on my notes and repost it as a part of your series. We'll figure out what to do with the IRQ mask on the next review round.
Em, I see.
In dwmac1000_dma.c:
1. Convert dwmac1000_dma_init() to being dwmac1000_dma_init_channel(); (No DMA_INTR_DEFAULT_MASK_LOONGSON)
2. Drop the stmmac_dma_ops.init() callback;
3. Leave other parts of the patch unchanged, such as DMA_CHAN_BASE_OFFSET;
In dwmac-loongson.c:
1. Create the Loongson GNET-specific stmmac_dma_ops.dma_interrupt() and stmmac_dma_ops.init_chan(); (With DMA_INTR_DEFAULT_MASK_LOONGSON)
2. Move all the Loongson-specific macros from dwmac_dma.h to here;
3. Follow your comments in Patch 5 to continue;
Right?
Thanks,
Yanteng
Quoted 18 lines
-Serge(y)
Quoted 15 lines
Thanks for your review!
Thanks,
Yanteng
Quoted 7 lines
-Serge(y)
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +0
-0return ret; }Signature · 1 line
2.31.4
Re: [PATCH net-next v7 4/9] net: stmmac: Add multi-channel supports
Quoted 339 lines · Yanteng Si
Quoted 304 lines · Serge Semin
Hi Yanteng
Quoted 301 lines · Yanteng Si
Quoted 32 lines · Serge Semin
Quoted 31 lines · Yanteng Si
Loongson platforms use a DWGMAC which supports multi-channel.
Added
dwmac1000_dma_init_channel()andinit_chan(), factor out all the channel-specific setups fromdwmac1000_dma_init()to the new functiondma_config(), then distinguish dma initialization and multi-channel initialization through different parameters.Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- .../ethernet/stmicro/stmmac/dwmac1000_dma.c | 55 ++++++++++++++----- .../net/ethernet/stmicro/stmmac/dwmac_dma.h | 17 ++++++ .../net/ethernet/stmicro/stmmac/dwmac_lib.c | 30 +++++----- 3 files changed, 74 insertions(+), 28 deletions(-)drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +2
-1@@ -12,7 +12,8 @@Author: Giuseppe Cavallaro <[email protected]> *******************************************************************************/ -#include <asm/io.h> +#include <linux/io.h> +#include "stmmac.h" #include "dwmac1000.h" #include "dwmac_dma.h" @@ -70,13 +71,16 @@ static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi)writel (value, ioaddr +DMA_AXI_BUS_MODE ); }Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi) · line 76
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +3
-2-static void dwmac1000_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr, -struct stmmac_dma_cfg *dma_cfg,int atds) +static void dma_config (void __iomem *modeaddr,void __iomem *enaddr, +struct stmmac_dma_cfg *dma_cfg,u32 dma_intr_mask, +int atds)Please make sure the arguments are aligned with the function open parenthesis taking into account that tabs are of _8_ chars:
Documentation/process/coding-style.rst.OK.
Quoted 50 lines
Quoted 31 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +18
-3{ -u32 value =readl (ioaddr +DMA_BUS_MODE ); +u32 value;int txpbl = dma_cfg->txpbl ?: dma_cfg->pbl;int rxpbl = dma_cfg->rxpbl ?: dma_cfg->pbl; + value =readl (modeaddr); +/* * Set the DMA PBL (Programmable Burst Length) mode. * @@ -104,10 +108,34 @@ static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr,if (dma_cfg->aal) value |=DMA_BUS_MODE_AAL ; -writel (value, ioaddr +DMA_BUS_MODE ); +writel (value, modeaddr); +writel (dma_intr_mask, enaddr); +} + +static void dwmac1000_dma_init (struct stmmac_priv *priv,void __iomem *ioaddr, +struct stmmac_dma_cfg *dma_cfg,int atds) +{ +u32 dma_intr_mask;/* Mask interrupts by writing to CSR7 */ -writel (DMA_INTR_DEFAULT_MASK , ioaddr +DMA_INTR_ENA ); + dma_intr_mask =DMA_INTR_DEFAULT_MASK ; + +dma_config (ioaddr +DMA_BUS_MODE , ioaddr +DMA_INTR_ENA , + dma_cfg, dma_intr_mask, atds); +} + +static void dwmac1000_dma_init_channel(struct stmmac_priv *priv, void __iomem *ioaddr,drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr, · line 135
Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +10
-0+ struct stmmac_dma_cfg *dma_cfg, u32 chan) +{ +u32 dma_intr_mask; + +/* Mask interrupts by writing to CSR7 */ + dma_intr_mask =DMA_INTR_DEFAULT_MASK ; + +if (dma_cfg->multi_msi_en) + dma_config(ioaddr + DMA_CHAN_BUS_MODE(chan), + ioaddr + DMA_CHAN_INTR_ENA(chan), dma_cfg,Why so complicated?
stmmac_init_chan()is always supposed to be called in the same context asstmmac_dma_init()(stmmac_xdp_open()is wrong in not doing that). Seeing DW GMAC v3.x multi-channels feature is implemented as multiple sets of the same CSRs (except AV traffic control CSRs specific to channels 1 and higher which are left unused here anyway) you can just drop thestmmac_dma_ops.init()callback and convertdwmac1000_dma_init()to beingdwmac1000_dma_init_channel()with no significant modifications:Quoted 6 lines
< you wouldn't need to have a separate
dma_config()method. < you wouldn't need to check for thedma_cfg->multi_msi_enflag state since thestmmac_init_chan()method is called for as many times as there are channels available (at least 1 channel always exists). < just add atds argument.
< just convert the method to using the chan-dependent CSR macros.Yes, you are right.
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr, · line 138
Quoted 1 line
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +1
-0+ dma_intr_mask, dma_cfg->multi_msi_en);^ +-------------------------------------------------+This is wrong + ATDS flag means Alternative Descriptor Size. This flag enables the 8 dword DMA-descriptors size with some DMA-desc fields semantics changed (see
enh_desc.candnorm_desc.c). It's useful for PTP Timestamping, VLANs, AV feature, L3/L4 filtering, CSum offload Type 2 (if any of that available). It has nothing to do with the separate DMA IRQs. Just convert thestmmac_dma_ops.dma_init()callback to accepting the atds flag as an additional argument, use it here to activate the extended descriptor size and make sure the atds flag is passed to thestmmac_init_chan()method in the respective source code.OK.
Quoted 50 lines
Quoted 50 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +6
-6} static void dwmac1000_dma_init_rx(struct stmmac_priv *priv,@@ -116,7 +144,7 @@ static void dwmac1000_dma_init_rx(struct stmmac_priv *priv, dma_addr_t dma_rx_phy, u32 chan) {/* RX descriptor base address list must be written into DMA CSR3 */ - writel(lower_32_bits(dma_rx_phy), ioaddr + DMA_RCV_BASE_ADDR); + writel(lower_32_bits(dma_rx_phy), ioaddr + DMA_CHAN_RCV_BASE_ADDR(chan)); } static void dwmac1000_dma_init_tx(struct stmmac_priv *priv,@@ -125,7 +153,7 @@ static void dwmac1000_dma_init_tx(struct stmmac_priv *priv, dma_addr_t dma_tx_phy, u32 chan) {/* TX descriptor base address list must be written into DMA CSR4 */ - writel(lower_32_bits(dma_tx_phy), ioaddr + DMA_TX_BASE_ADDR); + writel(lower_32_bits(dma_tx_phy), ioaddr + DMA_CHAN_TX_BASE_ADDR(chan)); }static u32 dwmac1000_configure_fc (u32 csr6,int rxfifosz)@@ -153,7 +181,7 @@ static void dwmac1000_dma_operation_mode_rx(struct stmmac_priv *priv, void __iomem *ioaddr, int mode, u32 channel, int fifosz, u8 qmode) { - u32 csr6 = readl(ioaddr + DMA_CONTROL); + u32 csr6 = readl(ioaddr + DMA_CHAN_CONTROL(channel));if (mode ==SF_DMA_MODE ) {pr_debug ("GMAC: enable RX store and forward mode\n" );@@ -175,14 +203,14 @@ static void dwmac1000_dma_operation_mode_rx(struct stmmac_priv *priv,/* Configure flow control based on rx fifo size */ csr6 =dwmac1000_configure_fc (csr6, fifosz); -writel (csr6, ioaddr +DMA_CONTROL ); +writel (csr6, ioaddr +DMA_CHAN_CONTROL (channel)); }static void dwmac1000_dma_operation_mode_tx (struct stmmac_priv *priv,void __iomem *ioaddr,int mode,u32 channel,int fifosz,u8 qmode) { -u32 csr6 =readl (ioaddr +DMA_CONTROL ); +u32 csr6 =readl (ioaddr +DMA_CHAN_CONTROL (channel));if (mode ==SF_DMA_MODE ) {pr_debug ("GMAC: enable TX store and forward mode\n" );@@ -209,7 +237,7 @@ static void dwmac1000_dma_operation_mode_tx(struct stmmac_priv *priv, csr6 |=DMA_CONTROL_TTC_256 ; } -writel (csr6, ioaddr +DMA_CONTROL ); +writel (csr6, ioaddr +DMA_CHAN_CONTROL (channel)); } static void dwmac1000_dump_dma_regs(struct stmmac_priv *priv,@@ -271,12 +299,13 @@ static int dwmac1000_get_hw_feature(void __iomem *ioaddr,static void dwmac1000_rx_watchdog (struct stmmac_priv *priv,void __iomem *ioaddr,u32 riwt,u32 queue)Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static int dwmac1000_get_hw_feature(void __iomem *ioaddr, · line 307
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +1
-1{ -writel (riwt, ioaddr +DMA_RX_WATCHDOG ); +writel (riwt, ioaddr +DMA_CHAN_RX_WATCHDOG (queue)); }const struct stmmac_dma_ops dwmac1000_dma_ops = { .reset = dwmac_dma_reset, .init = dwmac1000_dma_init,This could be dropped. See my comment above.
OK, I've tried this and it works.
Quoted 5 lines
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +1
-0+ .init_chan = dwmac1000_dma_init_channel, .init_rx_chan = dwmac1000_dma_init_rx, .init_tx_chan = dwmac1000_dma_init_tx, .axi = dwmac1000_dma_axi,drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +0
-0Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h line 150
Quoted 7 lines
index
e7aef136824b..395d5e4c3922100644drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +1
-0@@ -148,6 +148,9 @@DMA_STATUS_TI | \ DMA_STATUS_MSK_COMMON) +/* Following DMA defines are chanels oriented */ s/chanels/channels
OK!
Quoted 3 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h line 152
Quoted 1 line
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +1
-0+#define DMA_CHAN_OFFSET 0x100
DMA_CHAN_BASE_OFFSET? to be looking the same as in DW QoS Eth GMAC v4.x/v5.x (dwmac4_dma.h).OK
Quoted 98 lines
Quoted 98 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +15
-0+#define NUM_DWMAC100_DMA_REGS 9#define NUM_DWMAC1000_DMA_REGS 23#define NUM_DWMAC4_DMA_REGS 27@@ -170,4 +173,18 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr, struct stmmac_extra_stats *x, u32 chan, u32 dir);int dwmac_dma_reset (void __iomem *ioaddr); +static inline u32 dma_chan_base_addr (u32 base,u32 chan) +{ +return base + chan *DMA_CHAN_OFFSET ; +} + +#define DMA_CHAN_XMT_POLL_DEMAND (chan) dma_chan_base_addr(DMA_XMT_POLL_DEMAND, chan) +#define DMA_CHAN_INTR_ENA (chan) dma_chan_base_addr(DMA_INTR_ENA, chan) +#define DMA_CHAN_CONTROL (chan) dma_chan_base_addr(DMA_CONTROL, chan) +#define DMA_CHAN_STATUS (chan) dma_chan_base_addr(DMA_STATUS, chan) +#define DMA_CHAN_BUS_MODE (chan) dma_chan_base_addr(DMA_BUS_MODE, chan) +#define DMA_CHAN_RCV_BASE_ADDR (chan) dma_chan_base_addr(DMA_RCV_BASE_ADDR, chan) +#define DMA_CHAN_TX_BASE_ADDR (chan) dma_chan_base_addr(DMA_TX_BASE_ADDR, chan) +#define DMA_CHAN_RX_WATCHDOG (chan) dma_chan_base_addr(DMA_RX_WATCHDOG, chan) +#endif /* __DWMAC_DMA_H__ */ drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +14
-14@@ -31,63 +31,63 @@ int dwmac_dma_reset(void __iomem *ioaddr)void dwmac_enable_dma_transmission (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -writel (1 , ioaddr +DMA_XMT_POLL_DEMAND ); +writel (1 , ioaddr +DMA_CHAN_XMT_POLL_DEMAND (chan)); }void dwmac_enable_dma_irq (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan,bool rx,bool tx) { -u32 value =readl (ioaddr +DMA_INTR_ENA ); +u32 value =readl (ioaddr +DMA_CHAN_INTR_ENA (chan));if (rx) value |=DMA_INTR_DEFAULT_RX ;if (tx) value |=DMA_INTR_DEFAULT_TX ; -writel (value, ioaddr +DMA_INTR_ENA ); +writel (value, ioaddr +DMA_CHAN_INTR_ENA (chan)); }void dwmac_disable_dma_irq (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan,bool rx,bool tx) { -u32 value =readl (ioaddr +DMA_INTR_ENA ); +u32 value =readl (ioaddr +DMA_CHAN_INTR_ENA (chan));if (rx) value &= ~DMA_INTR_DEFAULT_RX ;if (tx) value &= ~DMA_INTR_DEFAULT_TX ; -writel (value, ioaddr +DMA_INTR_ENA ); +writel (value, ioaddr +DMA_CHAN_INTR_ENA (chan)); }void dwmac_dma_start_tx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value |=DMA_CONTROL_ST ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }void dwmac_dma_stop_tx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value &= ~DMA_CONTROL_ST ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }void dwmac_dma_start_rx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value |=DMA_CONTROL_SR ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }void dwmac_dma_stop_rx (struct stmmac_priv *priv,void __iomem *ioaddr,u32 chan) { -u32 value =readl (ioaddr +DMA_CONTROL ); +u32 value =readl (ioaddr +DMA_CHAN_CONTROL (chan)); value &= ~DMA_CONTROL_SR ; -writel (value, ioaddr +DMA_CONTROL ); +writel (value, ioaddr +DMA_CHAN_CONTROL (chan)); }#ifdef DWMAC_DMA_DEBUG @@ -167,7 +167,7 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,struct stmmac_txq_stats *txq_stats = &priv->xstats.txq_stats[chan];int ret =0 ;/* read the status register (CSR5) */ -u32 intr_status =readl (ioaddr +DMA_STATUS ); +u32 intr_status =readl (ioaddr +DMA_CHAN_STATUS (chan));Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr, · line 239
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +1
-1#ifdef DWMAC_DMA_DEBUG /* Enable it to monitor DMA rx/tx status in case of critical problems */ @@ -237,7 +237,7 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,pr_warn ("%s: unexpected status %08x\n" , __func__, intr_status);/* Clear the interrupt by writing a logic 1 to the CSR5[15-0] */ -writel ((intr_status &0x1ffff ), ioaddr +DMA_STATUS ); +writel ((intr_status &0x7ffff ), ioaddr +DMA_CHAN_STATUS (chan));Em, please explain the mask change. Bits CSR5[17:28] are defined as RO
I'm not sure I can explain it, but it goes something like this:
We moved these bits up because we split the reception and transmission of interrupts.
Quoted 7 lines
Quoted 5 lines
28 Reserved
27:25 EB
24:22 TS
21:19 RS
18 NTISI see. Thanks for clarification. Let's postpone the IRQ mask discussion for the next review round.
OK.
Quoted 16 lines
Quoted 9 lines
Quoted 4 lines
on a normal DW GMAC. Anyway it seems like the mask changes belongs to the patch 5/9.
Yes, I will try.
Quoted 4 lines
Except the last comment, AFAICS this patch provides a generic DW GMAC v3.x multi-channel support. Despite of several issues noted above the change in general looks very good.
Quoted 7 lines
Thanks, the next version of this patch will only have changes related to
dma_chan_base_addr.*
dwmac1000_dma_initwill be restored.*
dwmac1000_dma_init_channel()will be moved todwmac-loongson.c.Quoted 8 lines
No. That's not what I meant. I said that this patch looks _generic_ enough to be applied (with my notes taken into account) in the common
dwmac1000_dma.ccode! It provides useful multi-DMA-channels support in a way it's implemented by the _generic_ DW GMAC v3.x IP-core. From that perspective the change will be useful for all users which DW GMACs support the multi-channels feature. Please fix the patch based on my notes and repost it as a part of your series. We'll figure out what to do with the IRQ mask on the next review round.
Quoted 7 lines
Em, I see.
In
dwmac1000_dma.c:1. Convert
dwmac1000_dma_init()to beingdwmac1000_dma_init_channel(); (No DMA_INTR_DEFAULT_MASK_LOONGSON)
Right.
Quoted 2 lines
2. Drop the
stmmac_dma_ops.init()callback;
Right. (I'd say that this is implied by 1.)
Quoted 2 lines
3. Leave other parts of the patch unchanged, such as
DMA_CHAN_BASE_OFFSET;
Right. Just take my comments to this patch into account and drop the Loongson-specific changes, like 0x1ffff->0x7ffff change in dwmac_dma_interrupt().
Quoted 9 lines
In dwmac-loongson.c:
1. Create the Loongson GNET-specific
stmmac_dma_ops.dma_interrupt()andstmmac_dma_ops.init_chan(); (With DMA_INTR_DEFAULT_MASK_LOONGSON)
2. Move all the Loongson-specific macros fromdwmac_dma.hto here;
3. Follow your comments in Patch 5 to continue;Right?
Right. This patch should be preserved because it will be useful for the driver further evolution and for the users having multi-channel DW GMAC v3.x devices. Meanwhile if you implement what I suggested in Patch 5, there will be almost no need in the generic STMMAC driver code update.
-Serge(y)
Quoted 24 lines
Thanks,
YantengQuoted 18 lines
-Serge(y)
Quoted 15 lines
Thanks for your review!
Thanks,
Yanteng
Quoted 7 lines
-Serge(y)
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +0
-0return ret; }Signature · 1 line
2.31.4
PATCH v7 5/9 net: stmmac: Add Loongson-specific register definitions
In reply to Yanteng SiThere are two types of Loongson DWGMAC. The first type shares the same register definitions and has similar logic as dwmac1000. The second type uses several different register definitions, we think it is necessary to distinguish rx and tx, so we split these bits into two.
Simply put, we split some single bit fields into double bits fileds:
Name Tx Rx
DMA_INTR_ENA_NIE = 0x00040000 | 0x00020000; DMA_INTR_ENA_AIE = 0x00010000 | 0x00008000; DMA_STATUS_NIS = 0x00040000 | 0x00020000; DMA_STATUS_AIS = 0x00010000 | 0x00008000; DMA_STATUS_FBI = 0x00002000 | 0x00001000;
Therefore, when using, TX and RX must be set at the same time.
--- drivers/net/ethernet/stmicro/stmmac/common.h | 1 + .../ethernet/stmicro/stmmac/dwmac-loongson.c | 2 ++ .../ethernet/stmicro/stmmac/dwmac1000_dma.c | 10 ++++-- .../net/ethernet/stmicro/stmmac/dwmac_dma.h | 35 +++++++++++++++++++ .../net/ethernet/stmicro/stmmac/dwmac_lib.c | 35 +++++++++++++++---- drivers/net/ethernet/stmicro/stmmac/hwif.c | 3 +- .../net/ethernet/stmicro/stmmac/stmmac_main.c | 1 + include/linux/stmmac.h | 1 + 8 files changed, 78 insertions(+), 10 deletions(-)
drivers/net/ethernet/stmicro/stmmac/common.h +1 -0
@@ -34,6 +34,7 @@#define DWMAC_CORE_5_00 0x50#define DWMAC_CORE_5_10 0x51#define DWMAC_CORE_5_20 0x52 +#define DWLGMAC_CORE_1_00 0x10#define DWXGMAC_CORE_2_10 0x21#define DWXGMAC_CORE_2_20 0x22#define DWXLGMAC_CORE_2_00 0x20
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +2 -0
@@ -101,6 +101,8 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, plat->mdio_bus_data->needs_reset = true; } + plat->flags |=STMMAC_FLAG_HAS_LGMAC ; +/* Enable pci device */ ret =pci_enable_device (pdev);if (ret) {
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +8 -2
@@ -118,7 +118,10 @@ static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr,u32 dma_intr_mask;/* Mask interrupts by writing to CSR7 */ - dma_intr_mask =DMA_INTR_DEFAULT_MASK ; +if (priv->plat->flags &STMMAC_FLAG_HAS_LGMAC ) + dma_intr_mask =DMA_INTR_DEFAULT_MASK_LOONGSON ; +else + dma_intr_mask =DMA_INTR_DEFAULT_MASK ;dma_config (ioaddr +DMA_BUS_MODE , ioaddr +DMA_INTR_ENA , dma_cfg, dma_intr_mask, atds);
@@ -130,7 +133,10 @@ static void dwmac1000_dma_init_channel(struct stmmac_priv *priv, void __iomem *iu32 dma_intr_mask;/* Mask interrupts by writing to CSR7 */ - dma_intr_mask =DMA_INTR_DEFAULT_MASK ; +if (priv->plat->flags &STMMAC_FLAG_HAS_LGMAC ) + dma_intr_mask =DMA_INTR_DEFAULT_MASK_LOONGSON ; +else + dma_intr_mask =DMA_INTR_DEFAULT_MASK ;if (dma_cfg->multi_msi_en) dma_config(ioaddr + DMA_CHAN_BUS_MODE(chan),
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +35 -0
@@ -70,16 +70,23 @@#define DMA_CONTROL_SR 0x00000002/* Start/Stop Receive */ /* DMA Normal interrupt */ +#define DMA_INTR_ENA_NIE_TX_LOONGSON 0x00040000/* Normal Loongson Tx Summary */ +#define DMA_INTR_ENA_NIE_RX_LOONGSON 0x00020000/* Normal Loongson Rx Summary */ #define DMA_INTR_ENA_NIE 0x00010000/* Normal Summary */ #define DMA_INTR_ENA_TIE 0x00000001/* Transmit Interrupt */ #define DMA_INTR_ENA_TUE 0x00000004/* Transmit Buffer Unavailable */ #define DMA_INTR_ENA_RIE 0x00000040/* Receive Interrupt */ #define DMA_INTR_ENA_ERE 0x00004000/* Early Receive */ +#define DMA_INTR_NORMAL_LOONGSON (DMA_INTR_ENA_NIE_TX_LOONGSON | \ + DMA_INTR_ENA_NIE_RX_LOONGSON | DMA_INTR_ENA_RIE | \ + DMA_INTR_ENA_TIE)#define DMA_INTR_NORMAL (DMA_INTR_ENA_NIE | DMA_INTR_ENA_RIE | \ DMA_INTR_ENA_TIE)/* DMA Abnormal interrupt */ +#define DMA_INTR_ENA_AIE_TX_LOONGSON 0x00010000/* Abnormal Loongson Tx Summary */ +#define DMA_INTR_ENA_AIE_RX_LOONGSON 0x00008000/* Abnormal Loongson Rx Summary */ #define DMA_INTR_ENA_AIE 0x00008000/* Abnormal Summary */ #define DMA_INTR_ENA_FBE 0x00002000/* Fatal Bus Error */ #define DMA_INTR_ENA_ETE 0x00000400/* Early Transmit */
@@ -91,10 +98,14 @@#define DMA_INTR_ENA_TJE 0x00000008/* Transmit Jabber */ #define DMA_INTR_ENA_TSE 0x00000002/* Transmit Stopped */ +#define DMA_INTR_ABNORMAL_LOONGSON (DMA_INTR_ENA_AIE_TX_LOONGSON | \ + DMA_INTR_ENA_AIE_RX_LOONGSON | DMA_INTR_ENA_FBE | \ + DMA_INTR_ENA_UNE)#define DMA_INTR_ABNORMAL (DMA_INTR_ENA_AIE | DMA_INTR_ENA_FBE | \ DMA_INTR_ENA_UNE)/* DMA default interrupt mask */ +#define DMA_INTR_DEFAULT_MASK_LOONGSON (DMA_INTR_NORMAL_LOONGSON | DMA_INTR_ABNORMAL_LOONGSON)#define DMA_INTR_DEFAULT_MASK (DMA_INTR_NORMAL | DMA_INTR_ABNORMAL)#define DMA_INTR_DEFAULT_RX (DMA_INTR_ENA_RIE)#define DMA_INTR_DEFAULT_TX (DMA_INTR_ENA_TIE)
@@ -111,9 +122,15 @@#define DMA_STATUS_TS_SHIFT 20#define DMA_STATUS_RS_MASK 0x000e0000/* Receive Process State */ #define DMA_STATUS_RS_SHIFT 17 +#define DMA_STATUS_NIS_TX_LOONGSON 0x00040000/* Normal Loongson Tx Interrupt Summary */ +#define DMA_STATUS_NIS_RX_LOONGSON 0x00020000/* Normal Loongson Rx Interrupt Summary */ #define DMA_STATUS_NIS 0x00010000/* Normal Interrupt Summary */ +#define DMA_STATUS_AIS_TX_LOONGSON 0x00010000/* Abnormal Loongson Tx Interrupt Summary */ +#define DMA_STATUS_AIS_RX_LOONGSON 0x00008000/* Abnormal Loongson Rx Interrupt Summary */ #define DMA_STATUS_AIS 0x00008000/* Abnormal Interrupt Summary */ #define DMA_STATUS_ERI 0x00004000/* Early Receive Interrupt */ +#define DMA_STATUS_FBI_TX_LOONGSON 0x00002000/* Fatal Loongson Tx Bus Error Interrupt */ +#define DMA_STATUS_FBI_RX_LOONGSON 0x00001000/* Fatal Loongson Rx Bus Error Interrupt */ #define DMA_STATUS_FBI 0x00002000/* Fatal Bus Error Interrupt */ #define DMA_STATUS_ETI 0x00000400/* Early Transmit Interrupt */ #define DMA_STATUS_RWT 0x00000200/* Receive Watchdog Timeout */
@@ -128,10 +145,21 @@#define DMA_STATUS_TI 0x00000001/* Transmit Interrupt */ #define DMA_CONTROL_FTF 0x00100000/* Flush transmit FIFO */ +#define DMA_STATUS_MSK_COMMON_LOONGSON (DMA_STATUS_NIS_TX_LOONGSON | \ + DMA_STATUS_NIS_RX_LOONGSON | DMA_STATUS_AIS_TX_LOONGSON | \ + DMA_STATUS_AIS_RX_LOONGSON | DMA_STATUS_FBI_TX_LOONGSON | \ + DMA_STATUS_FBI_RX_LOONGSON)#define DMA_STATUS_MSK_COMMON (DMA_STATUS_NIS | \ DMA_STATUS_AIS | \ DMA_STATUS_FBI) +#define DMA_STATUS_MSK_RX_LOONGSON (DMA_STATUS_ERI | \ + DMA_STATUS_RWT | \ + DMA_STATUS_RPS | \ + DMA_STATUS_RU | \ + DMA_STATUS_RI | \ + DMA_STATUS_OVF | \ + DMA_STATUS_MSK_COMMON_LOONGSON)#define DMA_STATUS_MSK_RX (DMA_STATUS_ERI | \ DMA_STATUS_RWT | \ DMA_STATUS_RPS | \
@@ -140,6 +168,13 @@ DMA_STATUS_OVF | \ DMA_STATUS_MSK_COMMON) +#define DMA_STATUS_MSK_TX_LOONGSON (DMA_STATUS_ETI | \ + DMA_STATUS_UNF | \ + DMA_STATUS_TJT | \ + DMA_STATUS_TU | \ + DMA_STATUS_TPS | \ + DMA_STATUS_TI | \ + DMA_STATUS_MSK_COMMON_LOONGSON)#define DMA_STATUS_MSK_TX (DMA_STATUS_ETI | \ DMA_STATUS_UNF | \ DMA_STATUS_TJT | \
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +28 -7
@@ -167,6 +167,9 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,struct stmmac_txq_stats *txq_stats = &priv->xstats.txq_stats[chan];int ret =0 ;/* read the status register (CSR5) */ +u32 nor_intr_status; +u32 abnor_intr_status; +u32 fb_intr_status;u32 intr_status =readl (ioaddr +DMA_CHAN_STATUS (chan));#ifdef DWMAC_DMA_DEBUG
@@ -176,13 +179,31 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,show_rx_process_state (intr_status);#endif -if (dir ==DMA_DIR_RX ) - intr_status &=DMA_STATUS_MSK_RX ; -else if (dir ==DMA_DIR_TX ) - intr_status &=DMA_STATUS_MSK_TX ; +if (priv->plat->flags &STMMAC_FLAG_HAS_LGMAC ) { +if (dir ==DMA_DIR_RX ) + intr_status &=DMA_STATUS_MSK_RX_LOONGSON ; +else if (dir ==DMA_DIR_TX ) + intr_status &=DMA_STATUS_MSK_TX_LOONGSON ; + + nor_intr_status = intr_status & \ + (DMA_STATUS_NIS_TX_LOONGSON |DMA_STATUS_NIS_RX_LOONGSON ); + abnor_intr_status = intr_status & \ + (DMA_STATUS_AIS_TX_LOONGSON |DMA_STATUS_AIS_RX_LOONGSON ); + fb_intr_status = intr_status & \ + (DMA_STATUS_FBI_TX_LOONGSON |DMA_STATUS_FBI_RX_LOONGSON ); + }else { +if (dir ==DMA_DIR_RX ) + intr_status &=DMA_STATUS_MSK_RX ; +else if (dir ==DMA_DIR_TX ) + intr_status &=DMA_STATUS_MSK_TX ; + + nor_intr_status = intr_status &DMA_STATUS_NIS ; + abnor_intr_status = intr_status &DMA_STATUS_AIS ; + fb_intr_status = intr_status &DMA_STATUS_FBI ; + }/* ABNORMAL interrupts */ -if (unlikely (intr_status &DMA_STATUS_AIS )) { +if (unlikely (abnor_intr_status)) {if (unlikely (intr_status &DMA_STATUS_UNF )) { ret = tx_hard_error_bump_tc; x->tx_undeflow_irq++;
@@ -205,13 +226,13 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr, x->tx_process_stopped_irq++; ret = tx_hard_error; } -if (unlikely (intr_status &DMA_STATUS_FBI )) { +if (unlikely (intr_status & fb_intr_status)) { x->fatal_bus_error_irq++; ret = tx_hard_error; } }/* TX/RX NORMAL interrupts */ -if (likely (intr_status &DMA_STATUS_NIS )) { +if (likely (nor_intr_status)) {if (likely (intr_status &DMA_STATUS_RI )) {u32 value =readl (ioaddr +DMA_INTR_ENA );/* to schedule NAPI on real RIE event. */
drivers/net/ethernet/stmicro/stmmac/hwif.c +2 -1
@@ -59,7 +59,8 @@ static int stmmac_dwmac1_quirks(struct stmmac_priv *priv)dev_info (priv->device,"Enhanced/Alternate descriptors\n" );/* GMAC older than 3.50 has no extended descriptors */ -if (priv->synopsys_id >=DWMAC_CORE_3_50 ) { +if (priv->synopsys_id >=DWMAC_CORE_3_50 || + priv->synopsys_id ==DWLGMAC_CORE_1_00 ) {dev_info (priv->device,"Enabled extended descriptors\n" ); priv->extend_desc =1 ; }else {
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +1 -0
@@ -7218,6 +7218,7 @@ static int stmmac_hw_init(struct stmmac_priv *priv)* riwt_off field from the platform. */ if (((priv->synopsys_id >=DWMAC_CORE_3_50 ) || + (priv->synopsys_id ==DWLGMAC_CORE_1_00 ) || (priv->plat->has_xgmac)) && (!priv->plat->riwt_off)) { priv->use_riwt =1 ; dev_info(priv->device,
include/linux/stmmac.h +1 -0
@@ -221,6 +221,7 @@ struct dwmac4_addrs {#define STMMAC_FLAG_RX_CLK_RUNS_IN_LPI BIT(10)#define STMMAC_FLAG_EN_TX_LPI_CLOCKGATING BIT(11)#define STMMAC_FLAG_HWTSTAMP_CORRECT_LATENCY BIT(12) +#define STMMAC_FLAG_HAS_LGMAC BIT(13)struct plat_stmmacenet_data {int bus_id;
Signature · 1 line
2.31.4
Re: [PATCH net-next v7 5/9] net: stmmac: Add Loongson-specific register definitions
Quoted 9 lines · Yanteng Si
There are two types of Loongson DWGMAC. The first type shares the same register definitions and has similar logic as dwmac1000. The second type uses several different register definitions, we think it is necessary to distinguish rx and tx, so we split these bits into two.
Simply put, we split some single bit fields into double bits fileds:
Name Tx Rx
Quoted 7 lines
DMA_INTR_ENA_NIE = 0x00040000 | 0x00020000; DMA_INTR_ENA_AIE = 0x00010000 | 0x00008000; DMA_STATUS_NIS = 0x00040000 | 0x00020000; DMA_STATUS_AIS = 0x00010000 | 0x00008000; DMA_STATUS_FBI = 0x00002000 | 0x00001000;Therefore, when using, TX and RX must be set at the same time.
Thanks for the updated patch. It looks much clearer now. Thanks to that I came up with a better and less invasive solution. See my last comment for details.
Quoted 20 lines
Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- drivers/net/ethernet/stmicro/stmmac/common.h | 1 + .../ethernet/stmicro/stmmac/dwmac-loongson.c | 2 ++ .../ethernet/stmicro/stmmac/dwmac1000_dma.c | 10 ++++-- .../net/ethernet/stmicro/stmmac/dwmac_dma.h | 35 +++++++++++++++++++ .../net/ethernet/stmicro/stmmac/dwmac_lib.c | 35 +++++++++++++++---- drivers/net/ethernet/stmicro/stmmac/hwif.c | 3 +- .../net/ethernet/stmicro/stmmac/stmmac_main.c | 1 + include/linux/stmmac.h | 1 + 8 files changed, 78 insertions(+), 10 deletions(-)drivers/net/ethernet/stmicro/stmmac/common.h +0
-0
drivers/net/ethernet/stmicro/stmmac/common.h line 38
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/common.h +1
-0@@ -34,6 +34,7 @@#define DWMAC_CORE_5_00 0x50#define DWMAC_CORE_5_10 0x51#define DWMAC_CORE_5_20 0x52 +#define DWLGMAC_CORE_1_00 0x10
This doesn't look correct because these IDs have been defined for the Synopsys IP-core enumerations. Loongson GNET is definitely based on some DW GMAC v3.x IP-core, but instead of updating the USERVER field vendor just overwrote the GMAC_VERSION.SNPSVER field. From that perspective the correct solution would be to override the priv->synopsys_id field with a correct IP-core version (0x37?). See my last comment for details of how to do that.
Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/common.h +0
-0#define DWXGMAC_CORE_2_10 0x21#define DWXGMAC_CORE_2_20 0x22#define
DWXLGMAC_CORE_2_000x20drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +0
-0
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_dwmac_probe(struct pci_dev *pdev, · line 106
Quoted 6 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +2
-0@@ -101,6 +101,8 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, plat->mdio_bus_data->needs_reset = true; } + plat->flags |=STMMAC_FLAG_HAS_LGMAC ; +
If what I suggest in the last comment is implemented this will be unnecessary.
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c
Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +0
-0/* Enable pci device */ ret =pci_enable_device (pdev);drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +0
-0if (ret) {drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +0
-0
None of the generic parts (dwmac1000_dma.c, dwmac_dma.h, dwmac_lib.c) will need to be modified if you implement what I suggest in the last comment.
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr,
Quoted 1 line
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +0
-0@@ -118,7 +118,10 @@ static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr,
See my comment to patch 4/9. This method can be fully dropped in favor of having the dwmac1000_dma_init_channel() function implemented.
Quoted 190 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +8
-2u32 dma_intr_mask;/* Mask interrupts by writing to CSR7 */ - dma_intr_mask =DMA_INTR_DEFAULT_MASK ; +if (priv->plat->flags &STMMAC_FLAG_HAS_LGMAC ) + dma_intr_mask =DMA_INTR_DEFAULT_MASK_LOONGSON ; +else + dma_intr_mask =DMA_INTR_DEFAULT_MASK ;dma_config (ioaddr +DMA_BUS_MODE , ioaddr +DMA_INTR_ENA , dma_cfg, dma_intr_mask, atds);@@ -130,7 +133,10 @@ static void dwmac1000_dma_init_channel(struct stmmac_priv *priv, void __iomem *iu32 dma_intr_mask;/* Mask interrupts by writing to CSR7 */ - dma_intr_mask =DMA_INTR_DEFAULT_MASK ; +if (priv->plat->flags &STMMAC_FLAG_HAS_LGMAC ) + dma_intr_mask =DMA_INTR_DEFAULT_MASK_LOONGSON ; +else + dma_intr_mask =DMA_INTR_DEFAULT_MASK ;if (dma_cfg->multi_msi_en) dma_config(ioaddr + DMA_CHAN_BUS_MODE(chan),drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +35
-0@@ -70,16 +70,23 @@#define DMA_CONTROL_SR 0x00000002/* Start/Stop Receive */ /* DMA Normal interrupt */ +#define DMA_INTR_ENA_NIE_TX_LOONGSON 0x00040000/* Normal Loongson Tx Summary */ +#define DMA_INTR_ENA_NIE_RX_LOONGSON 0x00020000/* Normal Loongson Rx Summary */ #define DMA_INTR_ENA_NIE 0x00010000/* Normal Summary */ #define DMA_INTR_ENA_TIE 0x00000001/* Transmit Interrupt */ #define DMA_INTR_ENA_TUE 0x00000004/* Transmit Buffer Unavailable */ #define DMA_INTR_ENA_RIE 0x00000040/* Receive Interrupt */ #define DMA_INTR_ENA_ERE 0x00004000/* Early Receive */ +#define DMA_INTR_NORMAL_LOONGSON (DMA_INTR_ENA_NIE_TX_LOONGSON | \ + DMA_INTR_ENA_NIE_RX_LOONGSON | DMA_INTR_ENA_RIE | \ + DMA_INTR_ENA_TIE)#define DMA_INTR_NORMAL (DMA_INTR_ENA_NIE | DMA_INTR_ENA_RIE | \ DMA_INTR_ENA_TIE)/* DMA Abnormal interrupt */ +#define DMA_INTR_ENA_AIE_TX_LOONGSON 0x00010000/* Abnormal Loongson Tx Summary */ +#define DMA_INTR_ENA_AIE_RX_LOONGSON 0x00008000/* Abnormal Loongson Rx Summary */ #define DMA_INTR_ENA_AIE 0x00008000/* Abnormal Summary */ #define DMA_INTR_ENA_FBE 0x00002000/* Fatal Bus Error */ #define DMA_INTR_ENA_ETE 0x00000400/* Early Transmit */ @@ -91,10 +98,14 @@#define DMA_INTR_ENA_TJE 0x00000008/* Transmit Jabber */ #define DMA_INTR_ENA_TSE 0x00000002/* Transmit Stopped */ +#define DMA_INTR_ABNORMAL_LOONGSON (DMA_INTR_ENA_AIE_TX_LOONGSON | \ + DMA_INTR_ENA_AIE_RX_LOONGSON | DMA_INTR_ENA_FBE | \ + DMA_INTR_ENA_UNE)#define DMA_INTR_ABNORMAL (DMA_INTR_ENA_AIE | DMA_INTR_ENA_FBE | \ DMA_INTR_ENA_UNE)/* DMA default interrupt mask */ +#define DMA_INTR_DEFAULT_MASK_LOONGSON (DMA_INTR_NORMAL_LOONGSON | DMA_INTR_ABNORMAL_LOONGSON)#define DMA_INTR_DEFAULT_MASK (DMA_INTR_NORMAL | DMA_INTR_ABNORMAL)#define DMA_INTR_DEFAULT_RX (DMA_INTR_ENA_RIE)#define DMA_INTR_DEFAULT_TX (DMA_INTR_ENA_TIE)@@ -111,9 +122,15 @@#define DMA_STATUS_TS_SHIFT 20#define DMA_STATUS_RS_MASK 0x000e0000/* Receive Process State */ #define DMA_STATUS_RS_SHIFT 17 +#define DMA_STATUS_NIS_TX_LOONGSON 0x00040000/* Normal Loongson Tx Interrupt Summary */ +#define DMA_STATUS_NIS_RX_LOONGSON 0x00020000/* Normal Loongson Rx Interrupt Summary */ #define DMA_STATUS_NIS 0x00010000/* Normal Interrupt Summary */ +#define DMA_STATUS_AIS_TX_LOONGSON 0x00010000/* Abnormal Loongson Tx Interrupt Summary */ +#define DMA_STATUS_AIS_RX_LOONGSON 0x00008000/* Abnormal Loongson Rx Interrupt Summary */ #define DMA_STATUS_AIS 0x00008000/* Abnormal Interrupt Summary */ #define DMA_STATUS_ERI 0x00004000/* Early Receive Interrupt */ +#define DMA_STATUS_FBI_TX_LOONGSON 0x00002000/* Fatal Loongson Tx Bus Error Interrupt */ +#define DMA_STATUS_FBI_RX_LOONGSON 0x00001000/* Fatal Loongson Rx Bus Error Interrupt */ #define DMA_STATUS_FBI 0x00002000/* Fatal Bus Error Interrupt */ #define DMA_STATUS_ETI 0x00000400/* Early Transmit Interrupt */ #define DMA_STATUS_RWT 0x00000200/* Receive Watchdog Timeout */ @@ -128,10 +145,21 @@#define DMA_STATUS_TI 0x00000001/* Transmit Interrupt */ #define DMA_CONTROL_FTF 0x00100000/* Flush transmit FIFO */ +#define DMA_STATUS_MSK_COMMON_LOONGSON (DMA_STATUS_NIS_TX_LOONGSON | \ + DMA_STATUS_NIS_RX_LOONGSON | DMA_STATUS_AIS_TX_LOONGSON | \ + DMA_STATUS_AIS_RX_LOONGSON | DMA_STATUS_FBI_TX_LOONGSON | \ + DMA_STATUS_FBI_RX_LOONGSON)#define DMA_STATUS_MSK_COMMON (DMA_STATUS_NIS | \ DMA_STATUS_AIS | \ DMA_STATUS_FBI) +#define DMA_STATUS_MSK_RX_LOONGSON (DMA_STATUS_ERI | \ + DMA_STATUS_RWT | \ + DMA_STATUS_RPS | \ + DMA_STATUS_RU | \ + DMA_STATUS_RI | \ + DMA_STATUS_OVF | \ + DMA_STATUS_MSK_COMMON_LOONGSON)#define DMA_STATUS_MSK_RX (DMA_STATUS_ERI | \ DMA_STATUS_RWT | \ DMA_STATUS_RPS | \@@ -140,6 +168,13 @@ DMA_STATUS_OVF | \ DMA_STATUS_MSK_COMMON) +#define DMA_STATUS_MSK_TX_LOONGSON (DMA_STATUS_ETI | \ + DMA_STATUS_UNF | \ + DMA_STATUS_TJT | \ + DMA_STATUS_TU | \ + DMA_STATUS_TPS | \ + DMA_STATUS_TI | \ + DMA_STATUS_MSK_COMMON_LOONGSON)#define DMA_STATUS_MSK_TX (DMA_STATUS_ETI | \ DMA_STATUS_UNF | \ DMA_STATUS_TJT | \drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +28
-7@@ -167,6 +167,9 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,struct stmmac_txq_stats *txq_stats = &priv->xstats.txq_stats[chan];int ret =0 ;/* read the status register (CSR5) */ +u32 nor_intr_status; +u32 abnor_intr_status; +u32 fb_intr_status;u32 intr_status =readl (ioaddr +DMA_CHAN_STATUS (chan));#ifdef DWMAC_DMA_DEBUG @@ -176,13 +179,31 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,show_rx_process_state (intr_status);#endif -if (dir ==DMA_DIR_RX ) - intr_status &=DMA_STATUS_MSK_RX ; -else if (dir ==DMA_DIR_TX ) - intr_status &=DMA_STATUS_MSK_TX ; +if (priv->plat->flags &STMMAC_FLAG_HAS_LGMAC ) { +if (dir ==DMA_DIR_RX ) + intr_status &=DMA_STATUS_MSK_RX_LOONGSON ; +else if (dir ==DMA_DIR_TX ) + intr_status &=DMA_STATUS_MSK_TX_LOONGSON ; + + nor_intr_status = intr_status & \ + (DMA_STATUS_NIS_TX_LOONGSON |DMA_STATUS_NIS_RX_LOONGSON ); + abnor_intr_status = intr_status & \ + (DMA_STATUS_AIS_TX_LOONGSON |DMA_STATUS_AIS_RX_LOONGSON ); + fb_intr_status = intr_status & \ + (DMA_STATUS_FBI_TX_LOONGSON |DMA_STATUS_FBI_RX_LOONGSON ); + }else { +if (dir ==DMA_DIR_RX ) + intr_status &=DMA_STATUS_MSK_RX ; +else if (dir ==DMA_DIR_TX ) + intr_status &=DMA_STATUS_MSK_TX ; + + nor_intr_status = intr_status &DMA_STATUS_NIS ; + abnor_intr_status = intr_status &DMA_STATUS_AIS ; + fb_intr_status = intr_status &DMA_STATUS_FBI ; + }/* ABNORMAL interrupts */ -if (unlikely (intr_status &DMA_STATUS_AIS )) { +if (unlikely (abnor_intr_status)) {if (unlikely (intr_status &DMA_STATUS_UNF )) { ret = tx_hard_error_bump_tc; x->tx_undeflow_irq++;@@ -205,13 +226,13 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr, x->tx_process_stopped_irq++; ret = tx_hard_error; } -if (unlikely (intr_status &DMA_STATUS_FBI )) { +if (unlikely (intr_status & fb_intr_status)) { x->fatal_bus_error_irq++; ret = tx_hard_error; } }/* TX/RX NORMAL interrupts */ -if (likely (intr_status &DMA_STATUS_NIS )) { +if (likely (nor_intr_status)) {if (likely (intr_status &DMA_STATUS_RI )) {u32 value =readl (ioaddr +DMA_INTR_ENA );/* to schedule NAPI on real RIE event. */ drivers/net/ethernet/stmicro/stmmac/hwif.c +0
-0
drivers/net/ethernet/stmicro/stmmac/hwif.c static int stmmac_dwmac1_quirks(struct stmmac_priv *priv) · line 64
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/hwif.c +2
-1@@ -59,7 +59,8 @@ static int stmmac_dwmac1_quirks(struct stmmac_priv *priv)dev_info (priv->device,"Enhanced/Alternate descriptors\n" );/* GMAC older than 3.50 has no extended descriptors */ -if (priv->synopsys_id >=DWMAC_CORE_3_50 ) { +if (priv->synopsys_id >=DWMAC_CORE_3_50 || + priv->synopsys_id ==DWLGMAC_CORE_1_00 ) {
This could be left as is if the priv->synopsys_id field is overwritten with a correct value (see my last comment).
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c static int stmmac_hw_init(struct stmmac_priv *priv) · line 7222
Quoted 13 lines
drivers/net/ethernet/stmicro/stmmac/hwif.c +0
-0dev_info (priv->device,"Enabled extended descriptors\n" ); priv->extend_desc =1 ;drivers/net/ethernet/stmicro/stmmac/hwif.c +0
-0}else {drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +1
-0@@ -7218,6 +7218,7 @@ static int stmmac_hw_init(struct stmmac_priv *priv)* riwt_off field from the platform. */ if (((priv->synopsys_id >= DWMAC_CORE_3_50) || + (priv->synopsys_id == DWLGMAC_CORE_1_00) ||
the same comment here.
include/linux/stmmac.h struct dwmac4_addrs { · line 224
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +0
-0(priv->plat->has_xgmac)) && (!priv->plat->riwt_off)) { priv->use_riwt =1 ;drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +0
-0dev_info(priv->device,include/linux/stmmac.h +1
-0@@ -221,6 +221,7 @@ struct dwmac4_addrs {#define STMMAC_FLAG_RX_CLK_RUNS_IN_LPI BIT(10)#define STMMAC_FLAG_EN_TX_LPI_CLOCKGATING BIT(11)#define STMMAC_FLAG_HWTSTAMP_CORRECT_LATENCY BIT(12) +#define STMMAC_FLAG_HAS_LGMAC BIT(13)
Seeing the patch in the current state would overcomplicate the generic code and the only functions you need to update are dwmac_dma_interrupt()dwmac1000_dma_init_channel()
you can have these methods re-defined with all the Loongson GNET specifics in the low-level platform driver (dwmac-loongson.c). After that you can just override the mac_device_info.dma pointer with a fixed stmmac_dma_ops descriptor. Here is what should be done for that:
1. Keep the Patch 4/9 with my comments fixed. First it will be partly useful for your GNET device. Second in general it's a correct implementation of the normal DW GMAC v3.x multi-channels feature and will be useful for the DW GMACs with that feature enabled.
2. Create the Loongson GNET-specific stmmac_dma_ops.dma_interrupt()stmmac_dma_ops.init_chan()
methods in the dwmac-loongson.c driver. Don't forget to move all the Loongson-specific macros from dwmac_dma.h to dwmac-loongson.c.
3. Create a Loongson GNET-specific platform setup method with the next semantics:
+ allocate stmmac_dma_ops instance and initialize it with
dwmac1000_dma_ops.
+ override the stmmac_dma_ops.{dma_interrupt, init_chan} with the pointers to the methods defined in 2.
+ allocate mac_device_info instance and initialize the mac_device_info.dma field with a pointer to the new stmmac_dma_ops instance.
+ call dwmac1000_setup() or initialize mac_device_info in a way it's done in dwmac1000_setup() (the later might be better so you wouldn't need to export the dwmac1000_setup() function).
+ override stmmac_priv.synopsys_id with a correct value.
4. Initialize plat_stmmacenet_data.setup() with the pointer to the method created in 3.
If I didn't miss something stmmac_hwif_init() will call the platform-specific setup method right after fetching the SNPSVER field value. Your setup method will allocate mac_device_info structure then, will pre-initialize the GNET-specific DMA ops field and fix the Synopsys ID with a proper value (as described in 3 above). The rest of the ops descriptors will be initialized in the loop afterwards based on the specified device ID.
-Serge(y)
Quoted 6 lines
include/linux/stmmac.h +0
-0struct plat_stmmacenet_data {int bus_id;Signature · 1 line
2.31.4
Re: [PATCH net-next v7 5/9] net: stmmac: Add Loongson-specific register definitions
Quoted 35 lines · Serge Semin
Quoted 9 lines · Yanteng Si
There are two types of Loongson DWGMAC. The first type shares the same register definitions and has similar logic as dwmac1000. The second type uses several different register definitions, we think it is necessary to distinguish rx and tx, so we split these bits into two.
Simply put, we split some single bit fields into double bits fileds:
Name Tx Rx
Quoted 7 lines
DMA_INTR_ENA_NIE = 0x00040000 | 0x00020000; DMA_INTR_ENA_AIE = 0x00010000 | 0x00008000; DMA_STATUS_NIS = 0x00040000 | 0x00020000; DMA_STATUS_AIS = 0x00010000 | 0x00008000; DMA_STATUS_FBI = 0x00002000 | 0x00001000;Therefore, when using, TX and RX must be set at the same time.
Thanks for the updated patch. It looks much clearer now. Thanks to that I came up with a better and less invasive solution. See my last comment for details.
Quoted 14 lines
Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- drivers/net/ethernet/stmicro/stmmac/common.h | 1 + .../ethernet/stmicro/stmmac/dwmac-loongson.c | 2 ++ .../ethernet/stmicro/stmmac/dwmac1000_dma.c | 10 ++++-- .../net/ethernet/stmicro/stmmac/dwmac_dma.h | 35 +++++++++++++++++++ .../net/ethernet/stmicro/stmmac/dwmac_lib.c | 35 +++++++++++++++---- drivers/net/ethernet/stmicro/stmmac/hwif.c | 3 +- .../net/ethernet/stmicro/stmmac/stmmac_main.c | 1 + include/linux/stmmac.h | 1 + 8 files changed, 78 insertions(+), 10 deletions(-)
Quoted 16 lines
drivers/net/ethernet/stmicro/stmmac/common.h line 37
Quoted 9 lines
drivers/net/ethernet/stmicro/stmmac/common.h +1
-0@@ -34,6 +34,7 @@#define DWMAC_CORE_5_00 0x50#define DWMAC_CORE_5_10 0x51#define DWMAC_CORE_5_20 0x52 +#define DWLGMAC_CORE_1_00 0x10This doesn't look correct because these IDs have been defined for the Synopsys IP-core enumerations. Loongson GNET is definitely based on some DW GMAC v3.x IP-core, but instead of updating the USERVER field vendor just overwrote the GMAC_VERSION.SNPSVER field. From that perspective the correct solution would be to override the
priv->synopsys_idfield with a correct IP-core version (0x37?). See my last comment for details of how to do that.
See my last reply.
Quoted 266 lines
Quoted 9 lines
drivers/net/ethernet/stmicro/stmmac/common.h +0
-0#define DWXGMAC_CORE_2_10 0x21#define DWXGMAC_CORE_2_20 0x22#define DWXLGMAC_CORE_2_00 0x20drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +0
-0drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_dwmac_probe(struct pci_dev *pdev, · line 105
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +2
-0@@ -101,6 +101,8 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, plat->mdio_bus_data->needs_reset = true; } + plat->flags |=STMMAC_FLAG_HAS_LGMAC ; +If what I suggest in the last comment is implemented this will be unnecessary.
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +0
-0/* Enable pci device */ ret =pci_enable_device (pdev);if (ret) {drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +0
-0None of the generic parts (
dwmac1000_dma.c,dwmac_dma.h,dwmac_lib.c) will need to be modified if you implement what I suggest in the last comment.drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr,
Quoted 1 line
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +0
-0@@ -118,7 +118,10 @@ static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr,See my comment to patch 4/9. This method can be fully dropped in favor of having the
dwmac1000_dma_init_channel()function implemented.Quoted 190 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +8
-2u32 dma_intr_mask;/* Mask interrupts by writing to CSR7 */ - dma_intr_mask =DMA_INTR_DEFAULT_MASK ; +if (priv->plat->flags &STMMAC_FLAG_HAS_LGMAC ) + dma_intr_mask =DMA_INTR_DEFAULT_MASK_LOONGSON ; +else + dma_intr_mask =DMA_INTR_DEFAULT_MASK ;dma_config (ioaddr +DMA_BUS_MODE , ioaddr +DMA_INTR_ENA , dma_cfg, dma_intr_mask, atds);@@ -130,7 +133,10 @@ static void dwmac1000_dma_init_channel(struct stmmac_priv *priv, void __iomem *iu32 dma_intr_mask;/* Mask interrupts by writing to CSR7 */ - dma_intr_mask =DMA_INTR_DEFAULT_MASK ; +if (priv->plat->flags &STMMAC_FLAG_HAS_LGMAC ) + dma_intr_mask =DMA_INTR_DEFAULT_MASK_LOONGSON ; +else + dma_intr_mask =DMA_INTR_DEFAULT_MASK ;if (dma_cfg->multi_msi_en) dma_config(ioaddr + DMA_CHAN_BUS_MODE(chan),drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +35
-0@@ -70,16 +70,23 @@#define DMA_CONTROL_SR 0x00000002/* Start/Stop Receive */ /* DMA Normal interrupt */ +#define DMA_INTR_ENA_NIE_TX_LOONGSON 0x00040000/* Normal Loongson Tx Summary */ +#define DMA_INTR_ENA_NIE_RX_LOONGSON 0x00020000/* Normal Loongson Rx Summary */ #define DMA_INTR_ENA_NIE 0x00010000/* Normal Summary */ #define DMA_INTR_ENA_TIE 0x00000001/* Transmit Interrupt */ #define DMA_INTR_ENA_TUE 0x00000004/* Transmit Buffer Unavailable */ #define DMA_INTR_ENA_RIE 0x00000040/* Receive Interrupt */ #define DMA_INTR_ENA_ERE 0x00004000/* Early Receive */ +#define DMA_INTR_NORMAL_LOONGSON (DMA_INTR_ENA_NIE_TX_LOONGSON | \ + DMA_INTR_ENA_NIE_RX_LOONGSON | DMA_INTR_ENA_RIE | \ + DMA_INTR_ENA_TIE)#define DMA_INTR_NORMAL (DMA_INTR_ENA_NIE | DMA_INTR_ENA_RIE | \ DMA_INTR_ENA_TIE)/* DMA Abnormal interrupt */ +#define DMA_INTR_ENA_AIE_TX_LOONGSON 0x00010000/* Abnormal Loongson Tx Summary */ +#define DMA_INTR_ENA_AIE_RX_LOONGSON 0x00008000/* Abnormal Loongson Rx Summary */ #define DMA_INTR_ENA_AIE 0x00008000/* Abnormal Summary */ #define DMA_INTR_ENA_FBE 0x00002000/* Fatal Bus Error */ #define DMA_INTR_ENA_ETE 0x00000400/* Early Transmit */ @@ -91,10 +98,14 @@#define DMA_INTR_ENA_TJE 0x00000008/* Transmit Jabber */ #define DMA_INTR_ENA_TSE 0x00000002/* Transmit Stopped */ +#define DMA_INTR_ABNORMAL_LOONGSON (DMA_INTR_ENA_AIE_TX_LOONGSON | \ + DMA_INTR_ENA_AIE_RX_LOONGSON | DMA_INTR_ENA_FBE | \ + DMA_INTR_ENA_UNE)#define DMA_INTR_ABNORMAL (DMA_INTR_ENA_AIE | DMA_INTR_ENA_FBE | \ DMA_INTR_ENA_UNE)/* DMA default interrupt mask */ +#define DMA_INTR_DEFAULT_MASK_LOONGSON (DMA_INTR_NORMAL_LOONGSON | DMA_INTR_ABNORMAL_LOONGSON)#define DMA_INTR_DEFAULT_MASK (DMA_INTR_NORMAL | DMA_INTR_ABNORMAL)#define DMA_INTR_DEFAULT_RX (DMA_INTR_ENA_RIE)#define DMA_INTR_DEFAULT_TX (DMA_INTR_ENA_TIE)@@ -111,9 +122,15 @@#define DMA_STATUS_TS_SHIFT 20#define DMA_STATUS_RS_MASK 0x000e0000/* Receive Process State */ #define DMA_STATUS_RS_SHIFT 17 +#define DMA_STATUS_NIS_TX_LOONGSON 0x00040000/* Normal Loongson Tx Interrupt Summary */ +#define DMA_STATUS_NIS_RX_LOONGSON 0x00020000/* Normal Loongson Rx Interrupt Summary */ #define DMA_STATUS_NIS 0x00010000/* Normal Interrupt Summary */ +#define DMA_STATUS_AIS_TX_LOONGSON 0x00010000/* Abnormal Loongson Tx Interrupt Summary */ +#define DMA_STATUS_AIS_RX_LOONGSON 0x00008000/* Abnormal Loongson Rx Interrupt Summary */ #define DMA_STATUS_AIS 0x00008000/* Abnormal Interrupt Summary */ #define DMA_STATUS_ERI 0x00004000/* Early Receive Interrupt */ +#define DMA_STATUS_FBI_TX_LOONGSON 0x00002000/* Fatal Loongson Tx Bus Error Interrupt */ +#define DMA_STATUS_FBI_RX_LOONGSON 0x00001000/* Fatal Loongson Rx Bus Error Interrupt */ #define DMA_STATUS_FBI 0x00002000/* Fatal Bus Error Interrupt */ #define DMA_STATUS_ETI 0x00000400/* Early Transmit Interrupt */ #define DMA_STATUS_RWT 0x00000200/* Receive Watchdog Timeout */ @@ -128,10 +145,21 @@#define DMA_STATUS_TI 0x00000001/* Transmit Interrupt */ #define DMA_CONTROL_FTF 0x00100000/* Flush transmit FIFO */ +#define DMA_STATUS_MSK_COMMON_LOONGSON (DMA_STATUS_NIS_TX_LOONGSON | \ + DMA_STATUS_NIS_RX_LOONGSON | DMA_STATUS_AIS_TX_LOONGSON | \ + DMA_STATUS_AIS_RX_LOONGSON | DMA_STATUS_FBI_TX_LOONGSON | \ + DMA_STATUS_FBI_RX_LOONGSON)#define DMA_STATUS_MSK_COMMON (DMA_STATUS_NIS | \ DMA_STATUS_AIS | \ DMA_STATUS_FBI) +#define DMA_STATUS_MSK_RX_LOONGSON (DMA_STATUS_ERI | \ + DMA_STATUS_RWT | \ + DMA_STATUS_RPS | \ + DMA_STATUS_RU | \ + DMA_STATUS_RI | \ + DMA_STATUS_OVF | \ + DMA_STATUS_MSK_COMMON_LOONGSON)#define DMA_STATUS_MSK_RX (DMA_STATUS_ERI | \ DMA_STATUS_RWT | \ DMA_STATUS_RPS | \@@ -140,6 +168,13 @@ DMA_STATUS_OVF | \ DMA_STATUS_MSK_COMMON) +#define DMA_STATUS_MSK_TX_LOONGSON (DMA_STATUS_ETI | \ + DMA_STATUS_UNF | \ + DMA_STATUS_TJT | \ + DMA_STATUS_TU | \ + DMA_STATUS_TPS | \ + DMA_STATUS_TI | \ + DMA_STATUS_MSK_COMMON_LOONGSON)#define DMA_STATUS_MSK_TX (DMA_STATUS_ETI | \ DMA_STATUS_UNF | \ DMA_STATUS_TJT | \drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +28
-7@@ -167,6 +167,9 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,struct stmmac_txq_stats *txq_stats = &priv->xstats.txq_stats[chan];int ret =0 ;/* read the status register (CSR5) */ +u32 nor_intr_status; +u32 abnor_intr_status; +u32 fb_intr_status;u32 intr_status =readl (ioaddr +DMA_CHAN_STATUS (chan));#ifdef DWMAC_DMA_DEBUG @@ -176,13 +179,31 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,show_rx_process_state (intr_status);#endif -if (dir ==DMA_DIR_RX ) - intr_status &=DMA_STATUS_MSK_RX ; -else if (dir ==DMA_DIR_TX ) - intr_status &=DMA_STATUS_MSK_TX ; +if (priv->plat->flags &STMMAC_FLAG_HAS_LGMAC ) { +if (dir ==DMA_DIR_RX ) + intr_status &=DMA_STATUS_MSK_RX_LOONGSON ; +else if (dir ==DMA_DIR_TX ) + intr_status &=DMA_STATUS_MSK_TX_LOONGSON ; + + nor_intr_status = intr_status & \ + (DMA_STATUS_NIS_TX_LOONGSON |DMA_STATUS_NIS_RX_LOONGSON ); + abnor_intr_status = intr_status & \ + (DMA_STATUS_AIS_TX_LOONGSON |DMA_STATUS_AIS_RX_LOONGSON ); + fb_intr_status = intr_status & \ + (DMA_STATUS_FBI_TX_LOONGSON |DMA_STATUS_FBI_RX_LOONGSON ); + }else { +if (dir ==DMA_DIR_RX ) + intr_status &=DMA_STATUS_MSK_RX ; +else if (dir ==DMA_DIR_TX ) + intr_status &=DMA_STATUS_MSK_TX ; + + nor_intr_status = intr_status &DMA_STATUS_NIS ; + abnor_intr_status = intr_status &DMA_STATUS_AIS ; + fb_intr_status = intr_status &DMA_STATUS_FBI ; + }/* ABNORMAL interrupts */ -if (unlikely (intr_status &DMA_STATUS_AIS )) { +if (unlikely (abnor_intr_status)) {if (unlikely (intr_status &DMA_STATUS_UNF )) { ret = tx_hard_error_bump_tc; x->tx_undeflow_irq++;@@ -205,13 +226,13 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr, x->tx_process_stopped_irq++; ret = tx_hard_error; } -if (unlikely (intr_status &DMA_STATUS_FBI )) { +if (unlikely (intr_status & fb_intr_status)) { x->fatal_bus_error_irq++; ret = tx_hard_error; } }/* TX/RX NORMAL interrupts */ -if (likely (intr_status &DMA_STATUS_NIS )) { +if (likely (nor_intr_status)) {if (likely (intr_status &DMA_STATUS_RI )) {u32 value =readl (ioaddr +DMA_INTR_ENA );/* to schedule NAPI on real RIE event. */ drivers/net/ethernet/stmicro/stmmac/hwif.c +0
-0drivers/net/ethernet/stmicro/stmmac/hwif.c static int stmmac_dwmac1_quirks(struct stmmac_priv *priv) · line 63
Quoted 6 lines
drivers/net/ethernet/stmicro/stmmac/hwif.c +2
-1@@ -59,7 +59,8 @@ static int stmmac_dwmac1_quirks(struct stmmac_priv *priv)dev_info (priv->device,"Enhanced/Alternate descriptors\n" );/* GMAC older than 3.50 has no extended descriptors */ -if (priv->synopsys_id >=DWMAC_CORE_3_50 ) { +if (priv->synopsys_id >=DWMAC_CORE_3_50 || + priv->synopsys_id ==DWLGMAC_CORE_1_00 ) {This could be left as is if the
priv->synopsys_idfield is overwritten with a correct value (see my last comment).drivers/net/ethernet/stmicro/stmmac/stmmac_main.c static int stmmac_hw_init(struct stmmac_priv *priv) · line 7221
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/hwif.c +0
-0dev_info (priv->device,"Enabled extended descriptors\n" ); priv->extend_desc =1 ; }else {drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +1
-0@@ -7218,6 +7218,7 @@ static int stmmac_hw_init(struct stmmac_priv *priv)* riwt_off field from the platform. */ if (((priv->synopsys_id >= DWMAC_CORE_3_50) || + (priv->synopsys_id == DWLGMAC_CORE_1_00) ||the same comment here.
include/linux/stmmac.h struct dwmac4_addrs { · line 224
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +0
-0(priv->plat->has_xgmac)) && (!priv->plat->riwt_off)) { priv->use_riwt =1 ; dev_info(priv->device,include/linux/stmmac.h +1
-0@@ -221,6 +221,7 @@ struct dwmac4_addrs {#define STMMAC_FLAG_RX_CLK_RUNS_IN_LPI BIT(10)#define STMMAC_FLAG_EN_TX_LPI_CLOCKGATING BIT(11)#define STMMAC_FLAG_HWTSTAMP_CORRECT_LATENCY BIT(12) +#define STMMAC_FLAG_HAS_LGMAC BIT(13)Seeing the patch in the current state would overcomplicate the generic code and the only functions you need to update are
dwmac_dma_interrupt()dwmac1000_dma_init_channel()
you can have these methods re-defined with all the Loongson GNET specifics in the low-level platform driver (dwmac-loongson.c). After that you can just override the mac_device_info.dma pointer with a fixedstmmac_dma_opsdescriptor. Here is what should be done for that:
Quoted 4 lines
1. Keep the Patch 4/9 with my comments fixed. First it will be partly useful for your GNET device. Second in general it's a correct implementation of the normal DW GMAC v3.x multi-channels feature and will be useful for the DW GMACs with that feature enabled.
OK.
Quoted 6 lines
2. Create the Loongson GNET-specific
stmmac_dma_ops.dma_interrupt()stmmac_dma_ops.init_chan()
methods in thedwmac-loongson.cdriver. Don't forget to move all the Loongson-specific macros fromdwmac_dma.htodwmac-loongson.c.
It's easy.
Quoted 5 lines
3. Create a Loongson GNET-specific platform setup method with the next semantics:
+ allocatestmmac_dma_opsinstance and initialize it withdwmac1000_dma_ops.
Do this in dwmac1000-dma.c? Because this seems impossible to achieve in dwmac-loongson.c:
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c:606:47: error: initializer element is not constant 606 | const struct stmmac_dma_ops dwlgmac_dma_ops = dwmac1000_dma_ops;
Quoted 2 lines
+ override the stmmac_dma_ops.{dma_interrupt,
init_chan} with the pointers to the methods defined in 2.
Likewise, where should I do this?
Sorry. I seem to have misinterpreted your meaning again.
Quoted 11 lines
+ allocate
mac_device_infoinstance and initialize the mac_device_info.dma field with a pointer to the newstmmac_dma_opsinstance.
+ calldwmac1000_setup()or initializemac_device_infoin a way it's done indwmac1000_setup()(the later might be better so you wouldn't need to export thedwmac1000_setup()function).
+ override stmmac_priv.synopsys_id with a correct value.4. Initialize
plat_stmmacenet_data.setup()with the pointer to the method created in 3.
Quoted 7 lines
If I didn't miss something
stmmac_hwif_init()will call the platform-specific setup method right after fetching the SNPSVER field value. Your setup method will allocatemac_device_infostructure then, will pre-initialize the GNET-specific DMA ops field and fix the Synopsys ID with a proper value (as described in 3 above). The rest of the ops descriptors will be initialized in the loop afterwards based on the specified device ID.
This doesn't seem to work because our device looks something like this:
device pci id reversion core version LS7A 0x13 0x00 0x35/0x37 LS7A 0x13 0x01 0x35/0x37 LS2K 0x13 0x00 0x10 LS2K 0x13 0x01 0x10
Thanks,
Yanteng
Quoted 9 lines
-Serge(y)
Quoted 6 lines
include/linux/stmmac.h +0
-0struct plat_stmmacenet_data {int bus_id;Signature · 1 line
2.31.4
Re: [PATCH net-next v7 5/9] net: stmmac: Add Loongson-specific register definitions
Quoted 329 lines · Yanteng Si
Quoted 35 lines · Serge Semin
Quoted 9 lines · Yanteng Si
There are two types of Loongson DWGMAC. The first type shares the same register definitions and has similar logic as dwmac1000. The second type uses several different register definitions, we think it is necessary to distinguish rx and tx, so we split these bits into two.
Simply put, we split some single bit fields into double bits fileds:
Name Tx Rx
Quoted 7 lines
DMA_INTR_ENA_NIE = 0x00040000 | 0x00020000; DMA_INTR_ENA_AIE = 0x00010000 | 0x00008000; DMA_STATUS_NIS = 0x00040000 | 0x00020000; DMA_STATUS_AIS = 0x00010000 | 0x00008000; DMA_STATUS_FBI = 0x00002000 | 0x00001000;Therefore, when using, TX and RX must be set at the same time.
Thanks for the updated patch. It looks much clearer now. Thanks to that I came up with a better and less invasive solution. See my last comment for details.
Quoted 14 lines
Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- drivers/net/ethernet/stmicro/stmmac/common.h | 1 + .../ethernet/stmicro/stmmac/dwmac-loongson.c | 2 ++ .../ethernet/stmicro/stmmac/dwmac1000_dma.c | 10 ++++-- .../net/ethernet/stmicro/stmmac/dwmac_dma.h | 35 +++++++++++++++++++ .../net/ethernet/stmicro/stmmac/dwmac_lib.c | 35 +++++++++++++++---- drivers/net/ethernet/stmicro/stmmac/hwif.c | 3 +- .../net/ethernet/stmicro/stmmac/stmmac_main.c | 1 + include/linux/stmmac.h | 1 + 8 files changed, 78 insertions(+), 10 deletions(-)Quoted 16 lines
drivers/net/ethernet/stmicro/stmmac/common.h line 37
Quoted 9 lines
drivers/net/ethernet/stmicro/stmmac/common.h +1
-0@@ -34,6 +34,7 @@#define DWMAC_CORE_5_00 0x50#define DWMAC_CORE_5_10 0x51#define DWMAC_CORE_5_20 0x52 +#define DWLGMAC_CORE_1_00 0x10This doesn't look correct because these IDs have been defined for the Synopsys IP-core enumerations. Loongson GNET is definitely based on some DW GMAC v3.x IP-core, but instead of updating the USERVER field vendor just overwrote the GMAC_VERSION.SNPSVER field. From that perspective the correct solution would be to override the
priv->synopsys_idfield with a correct IP-core version (0x37?). See my last comment for details of how to do that.See my last reply.
Quoted 249 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_dwmac_probe(struct pci_dev *pdev, · line 104
Quoted 13 lines
drivers/net/ethernet/stmicro/stmmac/common.h +0
-0#define DWXGMAC_CORE_2_10 0x21#define DWXGMAC_CORE_2_20 0x22#define DWXLGMAC_CORE_2_00 0x20drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +2
-0@@ -101,6 +101,8 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, plat->mdio_bus_data->needs_reset = true; } + plat->flags |=STMMAC_FLAG_HAS_LGMAC ; +If what I suggest in the last comment is implemented this will be unnecessary.
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +0
-0/* Enable pci device */ ret =pci_enable_device (pdev);if (ret) {drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +0
-0None of the generic parts (
dwmac1000_dma.c,dwmac_dma.h,dwmac_lib.c) will need to be modified if you implement what I suggest in the last comment.drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr,
Quoted 1 line
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +0
-0@@ -118,7 +118,10 @@ static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr,See my comment to patch 4/9. This method can be fully dropped in favor of having the
dwmac1000_dma_init_channel()function implemented.Quoted 175 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +8
-2u32 dma_intr_mask;/* Mask interrupts by writing to CSR7 */ - dma_intr_mask =DMA_INTR_DEFAULT_MASK ; +if (priv->plat->flags &STMMAC_FLAG_HAS_LGMAC ) + dma_intr_mask =DMA_INTR_DEFAULT_MASK_LOONGSON ; +else + dma_intr_mask =DMA_INTR_DEFAULT_MASK ;dma_config (ioaddr +DMA_BUS_MODE , ioaddr +DMA_INTR_ENA , dma_cfg, dma_intr_mask, atds);@@ -130,7 +133,10 @@ static void dwmac1000_dma_init_channel(struct stmmac_priv *priv, void __iomem *iu32 dma_intr_mask;/* Mask interrupts by writing to CSR7 */ - dma_intr_mask =DMA_INTR_DEFAULT_MASK ; +if (priv->plat->flags &STMMAC_FLAG_HAS_LGMAC ) + dma_intr_mask =DMA_INTR_DEFAULT_MASK_LOONGSON ; +else + dma_intr_mask =DMA_INTR_DEFAULT_MASK ;if (dma_cfg->multi_msi_en) dma_config(ioaddr + DMA_CHAN_BUS_MODE(chan),drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +35
-0@@ -70,16 +70,23 @@#define DMA_CONTROL_SR 0x00000002/* Start/Stop Receive */ /* DMA Normal interrupt */ +#define DMA_INTR_ENA_NIE_TX_LOONGSON 0x00040000/* Normal Loongson Tx Summary */ +#define DMA_INTR_ENA_NIE_RX_LOONGSON 0x00020000/* Normal Loongson Rx Summary */ #define DMA_INTR_ENA_NIE 0x00010000/* Normal Summary */ #define DMA_INTR_ENA_TIE 0x00000001/* Transmit Interrupt */ #define DMA_INTR_ENA_TUE 0x00000004/* Transmit Buffer Unavailable */ #define DMA_INTR_ENA_RIE 0x00000040/* Receive Interrupt */ #define DMA_INTR_ENA_ERE 0x00004000/* Early Receive */ +#define DMA_INTR_NORMAL_LOONGSON (DMA_INTR_ENA_NIE_TX_LOONGSON | \ + DMA_INTR_ENA_NIE_RX_LOONGSON | DMA_INTR_ENA_RIE | \ + DMA_INTR_ENA_TIE)#define DMA_INTR_NORMAL (DMA_INTR_ENA_NIE | DMA_INTR_ENA_RIE | \ DMA_INTR_ENA_TIE)/* DMA Abnormal interrupt */ +#define DMA_INTR_ENA_AIE_TX_LOONGSON 0x00010000/* Abnormal Loongson Tx Summary */ +#define DMA_INTR_ENA_AIE_RX_LOONGSON 0x00008000/* Abnormal Loongson Rx Summary */ #define DMA_INTR_ENA_AIE 0x00008000/* Abnormal Summary */ #define DMA_INTR_ENA_FBE 0x00002000/* Fatal Bus Error */ #define DMA_INTR_ENA_ETE 0x00000400/* Early Transmit */ @@ -91,10 +98,14 @@#define DMA_INTR_ENA_TJE 0x00000008/* Transmit Jabber */ #define DMA_INTR_ENA_TSE 0x00000002/* Transmit Stopped */ +#define DMA_INTR_ABNORMAL_LOONGSON (DMA_INTR_ENA_AIE_TX_LOONGSON | \ + DMA_INTR_ENA_AIE_RX_LOONGSON | DMA_INTR_ENA_FBE | \ + DMA_INTR_ENA_UNE)#define DMA_INTR_ABNORMAL (DMA_INTR_ENA_AIE | DMA_INTR_ENA_FBE | \ DMA_INTR_ENA_UNE)/* DMA default interrupt mask */ +#define DMA_INTR_DEFAULT_MASK_LOONGSON (DMA_INTR_NORMAL_LOONGSON | DMA_INTR_ABNORMAL_LOONGSON)#define DMA_INTR_DEFAULT_MASK (DMA_INTR_NORMAL | DMA_INTR_ABNORMAL)#define DMA_INTR_DEFAULT_RX (DMA_INTR_ENA_RIE)#define DMA_INTR_DEFAULT_TX (DMA_INTR_ENA_TIE)@@ -111,9 +122,15 @@#define DMA_STATUS_TS_SHIFT 20#define DMA_STATUS_RS_MASK 0x000e0000/* Receive Process State */ #define DMA_STATUS_RS_SHIFT 17 +#define DMA_STATUS_NIS_TX_LOONGSON 0x00040000/* Normal Loongson Tx Interrupt Summary */ +#define DMA_STATUS_NIS_RX_LOONGSON 0x00020000/* Normal Loongson Rx Interrupt Summary */ #define DMA_STATUS_NIS 0x00010000/* Normal Interrupt Summary */ +#define DMA_STATUS_AIS_TX_LOONGSON 0x00010000/* Abnormal Loongson Tx Interrupt Summary */ +#define DMA_STATUS_AIS_RX_LOONGSON 0x00008000/* Abnormal Loongson Rx Interrupt Summary */ #define DMA_STATUS_AIS 0x00008000/* Abnormal Interrupt Summary */ #define DMA_STATUS_ERI 0x00004000/* Early Receive Interrupt */ +#define DMA_STATUS_FBI_TX_LOONGSON 0x00002000/* Fatal Loongson Tx Bus Error Interrupt */ +#define DMA_STATUS_FBI_RX_LOONGSON 0x00001000/* Fatal Loongson Rx Bus Error Interrupt */ #define DMA_STATUS_FBI 0x00002000/* Fatal Bus Error Interrupt */ #define DMA_STATUS_ETI 0x00000400/* Early Transmit Interrupt */ #define DMA_STATUS_RWT 0x00000200/* Receive Watchdog Timeout */ @@ -128,10 +145,21 @@#define DMA_STATUS_TI 0x00000001/* Transmit Interrupt */ #define DMA_CONTROL_FTF 0x00100000/* Flush transmit FIFO */ +#define DMA_STATUS_MSK_COMMON_LOONGSON (DMA_STATUS_NIS_TX_LOONGSON | \ + DMA_STATUS_NIS_RX_LOONGSON | DMA_STATUS_AIS_TX_LOONGSON | \ + DMA_STATUS_AIS_RX_LOONGSON | DMA_STATUS_FBI_TX_LOONGSON | \ + DMA_STATUS_FBI_RX_LOONGSON)#define DMA_STATUS_MSK_COMMON (DMA_STATUS_NIS | \ DMA_STATUS_AIS | \ DMA_STATUS_FBI) +#define DMA_STATUS_MSK_RX_LOONGSON (DMA_STATUS_ERI | \ + DMA_STATUS_RWT | \ + DMA_STATUS_RPS | \ + DMA_STATUS_RU | \ + DMA_STATUS_RI | \ + DMA_STATUS_OVF | \ + DMA_STATUS_MSK_COMMON_LOONGSON)#define DMA_STATUS_MSK_RX (DMA_STATUS_ERI | \ DMA_STATUS_RWT | \ DMA_STATUS_RPS | \@@ -140,6 +168,13 @@ DMA_STATUS_OVF | \ DMA_STATUS_MSK_COMMON) +#define DMA_STATUS_MSK_TX_LOONGSON (DMA_STATUS_ETI | \ + DMA_STATUS_UNF | \ + DMA_STATUS_TJT | \ + DMA_STATUS_TU | \ + DMA_STATUS_TPS | \ + DMA_STATUS_TI | \ + DMA_STATUS_MSK_COMMON_LOONGSON)#define DMA_STATUS_MSK_TX (DMA_STATUS_ETI | \ DMA_STATUS_UNF | \ DMA_STATUS_TJT | \drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +28
-7@@ -167,6 +167,9 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,struct stmmac_txq_stats *txq_stats = &priv->xstats.txq_stats[chan];int ret =0 ;/* read the status register (CSR5) */ +u32 nor_intr_status; +u32 abnor_intr_status; +u32 fb_intr_status;u32 intr_status =readl (ioaddr +DMA_CHAN_STATUS (chan));#ifdef DWMAC_DMA_DEBUG @@ -176,13 +179,31 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,show_rx_process_state (intr_status);#endif -if (dir ==DMA_DIR_RX ) - intr_status &=DMA_STATUS_MSK_RX ; -else if (dir ==DMA_DIR_TX ) - intr_status &=DMA_STATUS_MSK_TX ; +if (priv->plat->flags &STMMAC_FLAG_HAS_LGMAC ) { +if (dir ==DMA_DIR_RX ) + intr_status &=DMA_STATUS_MSK_RX_LOONGSON ; +else if (dir ==DMA_DIR_TX ) + intr_status &=DMA_STATUS_MSK_TX_LOONGSON ; + + nor_intr_status = intr_status & \ + (DMA_STATUS_NIS_TX_LOONGSON |DMA_STATUS_NIS_RX_LOONGSON ); + abnor_intr_status = intr_status & \ + (DMA_STATUS_AIS_TX_LOONGSON |DMA_STATUS_AIS_RX_LOONGSON ); + fb_intr_status = intr_status & \ + (DMA_STATUS_FBI_TX_LOONGSON |DMA_STATUS_FBI_RX_LOONGSON ); + }else { +if (dir ==DMA_DIR_RX ) + intr_status &=DMA_STATUS_MSK_RX ; +else if (dir ==DMA_DIR_TX ) + intr_status &=DMA_STATUS_MSK_TX ; + + nor_intr_status = intr_status &DMA_STATUS_NIS ; + abnor_intr_status = intr_status &DMA_STATUS_AIS ; + fb_intr_status = intr_status &DMA_STATUS_FBI ; + }/* ABNORMAL interrupts */ -if (unlikely (intr_status &DMA_STATUS_AIS )) { +if (unlikely (abnor_intr_status)) {if (unlikely (intr_status &DMA_STATUS_UNF )) { ret = tx_hard_error_bump_tc; x->tx_undeflow_irq++;@@ -205,13 +226,13 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr, x->tx_process_stopped_irq++; ret = tx_hard_error; } -if (unlikely (intr_status &DMA_STATUS_FBI )) { +if (unlikely (intr_status & fb_intr_status)) { x->fatal_bus_error_irq++; ret = tx_hard_error; } }/* TX/RX NORMAL interrupts */ -if (likely (intr_status &DMA_STATUS_NIS )) { +if (likely (nor_intr_status)) {if (likely (intr_status &DMA_STATUS_RI )) {u32 value =readl (ioaddr +DMA_INTR_ENA );/* to schedule NAPI on real RIE event. */ drivers/net/ethernet/stmicro/stmmac/hwif.c +0
-0drivers/net/ethernet/stmicro/stmmac/hwif.c static int stmmac_dwmac1_quirks(struct stmmac_priv *priv) · line 62
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/hwif.c +2
-1@@ -59,7 +59,8 @@ static int stmmac_dwmac1_quirks(struct stmmac_priv *priv)dev_info (priv->device,"Enhanced/Alternate descriptors\n" );/* GMAC older than 3.50 has no extended descriptors */ -if (priv->synopsys_id >=DWMAC_CORE_3_50 ) { +if (priv->synopsys_id >=DWMAC_CORE_3_50 || + priv->synopsys_id ==DWLGMAC_CORE_1_00 ) {This could be left as is if the
priv->synopsys_idfield is overwritten with a correct value (see my last comment).drivers/net/ethernet/stmicro/stmmac/stmmac_main.c static int stmmac_hw_init(struct stmmac_priv *priv) · line 7221
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/hwif.c +0
-0dev_info (priv->device,"Enabled extended descriptors\n" ); priv->extend_desc =1 ; }else {drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +1
-0@@ -7218,6 +7218,7 @@ static int stmmac_hw_init(struct stmmac_priv *priv)* riwt_off field from the platform. */ if (((priv->synopsys_id >= DWMAC_CORE_3_50) || + (priv->synopsys_id == DWLGMAC_CORE_1_00) ||the same comment here.
include/linux/stmmac.h struct dwmac4_addrs { · line 224
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +0
-0(priv->plat->has_xgmac)) && (!priv->plat->riwt_off)) { priv->use_riwt =1 ; dev_info(priv->device,include/linux/stmmac.h +1
-0@@ -221,6 +221,7 @@ struct dwmac4_addrs {#define STMMAC_FLAG_RX_CLK_RUNS_IN_LPI BIT(10)#define STMMAC_FLAG_EN_TX_LPI_CLOCKGATING BIT(11)#define STMMAC_FLAG_HWTSTAMP_CORRECT_LATENCY BIT(12) +#define STMMAC_FLAG_HAS_LGMAC BIT(13)Seeing the patch in the current state would overcomplicate the generic code and the only functions you need to update are
dwmac_dma_interrupt()dwmac1000_dma_init_channel()
you can have these methods re-defined with all the Loongson GNET specifics in the low-level platform driver (dwmac-loongson.c). After that you can just override the mac_device_info.dma pointer with a fixedstmmac_dma_opsdescriptor. Here is what should be done for that:Quoted 4 lines
1. Keep the Patch 4/9 with my comments fixed. First it will be partly useful for your GNET device. Second in general it's a correct implementation of the normal DW GMAC v3.x multi-channels feature and will be useful for the DW GMACs with that feature enabled.
OK.
Quoted 6 lines
2. Create the Loongson GNET-specific
stmmac_dma_ops.dma_interrupt()stmmac_dma_ops.init_chan()
methods in thedwmac-loongson.cdriver. Don't forget to move all the Loongson-specific macros fromdwmac_dma.htodwmac-loongson.c.It's easy.
Quoted 5 lines
3. Create a Loongson GNET-specific platform setup method with the next semantics:
+ allocatestmmac_dma_opsinstance and initialize it withdwmac1000_dma_ops.Do this in
dwmac1000-dma.c? Because this seems impossible to achieve in dwmac-loongson.c:
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c:606:47: error:
initializer element is not constant
606 | const structstmmac_dma_opsdwlgmac_dma_ops=dwmac1000_dma_ops;
Quoted 6 lines
Quoted 2 lines
+ override the stmmac_dma_ops.{dma_interrupt,
init_chan} with the pointers to the methods defined in 2.Likewise, where should I do this?
Sorry. I seem to have misinterpreted your meaning again.
No worries. Here is what I meant:
1. Declare the private Loongson GMAC data like this:
struct loongson_data {
struct stmmac_dma_ops dma_ops;
};
2. Allocate the memory for the data in the framework of the Loongson
GMAC device probe() method:
loongson_dwmac_probe()
{
...
ld = devm_kzalloc(&pdev->dev, sizeof(*ld), GFP_KERNEL);
if (!ld)
return -ENOMEM;
...
ld->dma_ops = dwmac1000_dma_ops;
ld->dma_ops.init_chan = loongson_gnat_dma_init_chan;
ld->dma_ops.dma_interrupt = loongson_gnat_dma_interrupt;
...
plat->bsp_priv = ld;
}3. Define the Loongson-specific plat_stmmacenet_data.setup() method, which would re-init the stmmac_priv->synopsys_id with a correct value, allocate the DW *MAC hardware descriptor and pre-initialize it 'dma' field:
static struct mac_device_info loongson_gnet_setup(void *apriv)
{
struct stmmac_priv *priv = apriv;
struct mac_device_info *mac;
struct loongson_data *ld;
mac = devm_kzalloc(priv->device, sizeof(*mac), GFP_KERNEL);
if (!mac)
return NULL;
priv->synopsys_id = 0x37; // or whatever is a real version of your IP
ld = priv->plat->bsp_priv;
mac->dma = &ld->dma_ops;
dwmac1000_setup(); // Or Pre-initialize the respective "mac" fields as it's done in dwmac1000_setup()
return mac;
}4. Make sure the plat_stmmacenet_data->setup field is initialized with the Loongson GNAT-specific setup() method:
static int loongson_gnet_data(struct pci_dev *pdev,
struct plat_stmmacenet_data *plat)
{
...
plat->setup = loongson_gnet_setup;
...
}That shall do what I described in by previous message.
Note another platform which gets to define its own setup() method Sun8i:drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
although since it fully redefines the DMA-ops descriptor the only common part with your case is that it needs to have the setup() method too.
Quoted 23 lines
Quoted 14 lines
+ allocate
mac_device_infoinstance and initialize the mac_device_info.dma field with a pointer to the newstmmac_dma_opsinstance.
+ calldwmac1000_setup()or initializemac_device_infoin a way it's done indwmac1000_setup()(the later might be better so you wouldn't need to export thedwmac1000_setup()function).
+ override stmmac_priv.synopsys_id with a correct value.4. Initialize
plat_stmmacenet_data.setup()with the pointer to the method created in 3.Quoted 7 lines
If I didn't miss something
stmmac_hwif_init()will call the platform-specific setup method right after fetching the SNPSVER field value. Your setup method will allocatemac_device_infostructure then, will pre-initialize the GNET-specific DMA ops field and fix the Synopsys ID with a proper value (as described in 3 above). The rest of the ops descriptors will be initialized in the loop afterwards based on the specified device ID.
Quoted 1 line
This doesn't seem to work because our device looks something like this:
Please see my note above.
Quoted 6 lines
device pci id reversion core version LS7A 0x13 0x00 0x35/0x37 LS7A 0x13 0x01 0x35/0x37 LS2K 0x13 0x00
0x10LS2K 0x13 0x010x10
Not sure what you meant by providing this table to me and justifying that something wouldn't work. But it would have been much useful to provide a detailed description of what platforms and devices the current dwmac-loongson.c driver supports and what support you are trying to add. Cover-letter is a suitable place for it.
In anyway the DW GMAC IP-core can't be 0x10. Seeing your device is having the multi-channels support it must have a version closer to 0x37 (the highest IP-core version is 3.73a). Please reach the hardware engineers to clarify what actual DW GMAC IP-core has been utilized in your case.
-Serge(y)
Quoted 15 lines
Thanks,
Yanteng
Quoted 8 lines
-Serge(y)
Quoted 5 lines
include/linux/stmmac.h +0
-0struct plat_stmmacenet_data {int bus_id;Signature · 1 line
2.31.4
Re: [PATCH net-next v7 5/9] net: stmmac: Add Loongson-specific register definitions
Quoted 383 lines · Serge Semin
Quoted 320 lines · Yanteng Si
Quoted 35 lines · Serge Semin
Quoted 9 lines · Yanteng Si
There are two types of Loongson DWGMAC. The first type shares the same register definitions and has similar logic as dwmac1000. The second type uses several different register definitions, we think it is necessary to distinguish rx and tx, so we split these bits into two.
Simply put, we split some single bit fields into double bits fileds:
Name Tx Rx
Quoted 7 lines
DMA_INTR_ENA_NIE = 0x00040000 | 0x00020000; DMA_INTR_ENA_AIE = 0x00010000 | 0x00008000; DMA_STATUS_NIS = 0x00040000 | 0x00020000; DMA_STATUS_AIS = 0x00010000 | 0x00008000; DMA_STATUS_FBI = 0x00002000 | 0x00001000;Therefore, when using, TX and RX must be set at the same time.
Thanks for the updated patch. It looks much clearer now. Thanks to that I came up with a better and less invasive solution. See my last comment for details.
Quoted 14 lines
Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- drivers/net/ethernet/stmicro/stmmac/common.h | 1 + .../ethernet/stmicro/stmmac/dwmac-loongson.c | 2 ++ .../ethernet/stmicro/stmmac/dwmac1000_dma.c | 10 ++++-- .../net/ethernet/stmicro/stmmac/dwmac_dma.h | 35 +++++++++++++++++++ .../net/ethernet/stmicro/stmmac/dwmac_lib.c | 35 +++++++++++++++---- drivers/net/ethernet/stmicro/stmmac/hwif.c | 3 +- .../net/ethernet/stmicro/stmmac/stmmac_main.c | 1 + include/linux/stmmac.h | 1 + 8 files changed, 78 insertions(+), 10 deletions(-)Quoted 16 lines
drivers/net/ethernet/stmicro/stmmac/common.h line 37
Quoted 9 lines
drivers/net/ethernet/stmicro/stmmac/common.h +1
-0@@ -34,6 +34,7 @@#define DWMAC_CORE_5_00 0x50#define DWMAC_CORE_5_10 0x51#define DWMAC_CORE_5_20 0x52 +#define DWLGMAC_CORE_1_00 0x10This doesn't look correct because these IDs have been defined for the Synopsys IP-core enumerations. Loongson GNET is definitely based on some DW GMAC v3.x IP-core, but instead of updating the USERVER field vendor just overwrote the GMAC_VERSION.SNPSVER field. From that perspective the correct solution would be to override the
priv->synopsys_idfield with a correct IP-core version (0x37?). See my last comment for details of how to do that.See my last reply.
Quoted 248 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_dwmac_probe(struct pci_dev *pdev, · line 104
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/common.h +0
-0#define DWXGMAC_CORE_2_10 0x21#define DWXGMAC_CORE_2_20 0x22#define DWXLGMAC_CORE_2_00 0x20drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +2
-0@@ -101,6 +101,8 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, plat->mdio_bus_data->needs_reset = true; } + plat->flags |=STMMAC_FLAG_HAS_LGMAC ; +If what I suggest in the last comment is implemented this will be unnecessary.
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +0
-0/* Enable pci device */ ret =pci_enable_device (pdev);if (ret) {drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +0
-0None of the generic parts (
dwmac1000_dma.c,dwmac_dma.h,dwmac_lib.c) will need to be modified if you implement what I suggest in the last comment.drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr,
Quoted 1 line
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +0
-0@@ -118,7 +118,10 @@ static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr,See my comment to patch 4/9. This method can be fully dropped in favor of having the
dwmac1000_dma_init_channel()function implemented.Quoted 175 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +8
-2u32 dma_intr_mask;/* Mask interrupts by writing to CSR7 */ - dma_intr_mask =DMA_INTR_DEFAULT_MASK ; +if (priv->plat->flags &STMMAC_FLAG_HAS_LGMAC ) + dma_intr_mask =DMA_INTR_DEFAULT_MASK_LOONGSON ; +else + dma_intr_mask =DMA_INTR_DEFAULT_MASK ;dma_config (ioaddr +DMA_BUS_MODE , ioaddr +DMA_INTR_ENA , dma_cfg, dma_intr_mask, atds);@@ -130,7 +133,10 @@ static void dwmac1000_dma_init_channel(struct stmmac_priv *priv, void __iomem *iu32 dma_intr_mask;/* Mask interrupts by writing to CSR7 */ - dma_intr_mask =DMA_INTR_DEFAULT_MASK ; +if (priv->plat->flags &STMMAC_FLAG_HAS_LGMAC ) + dma_intr_mask =DMA_INTR_DEFAULT_MASK_LOONGSON ; +else + dma_intr_mask =DMA_INTR_DEFAULT_MASK ;if (dma_cfg->multi_msi_en) dma_config(ioaddr + DMA_CHAN_BUS_MODE(chan),drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +35
-0@@ -70,16 +70,23 @@#define DMA_CONTROL_SR 0x00000002/* Start/Stop Receive */ /* DMA Normal interrupt */ +#define DMA_INTR_ENA_NIE_TX_LOONGSON 0x00040000/* Normal Loongson Tx Summary */ +#define DMA_INTR_ENA_NIE_RX_LOONGSON 0x00020000/* Normal Loongson Rx Summary */ #define DMA_INTR_ENA_NIE 0x00010000/* Normal Summary */ #define DMA_INTR_ENA_TIE 0x00000001/* Transmit Interrupt */ #define DMA_INTR_ENA_TUE 0x00000004/* Transmit Buffer Unavailable */ #define DMA_INTR_ENA_RIE 0x00000040/* Receive Interrupt */ #define DMA_INTR_ENA_ERE 0x00004000/* Early Receive */ +#define DMA_INTR_NORMAL_LOONGSON (DMA_INTR_ENA_NIE_TX_LOONGSON | \ + DMA_INTR_ENA_NIE_RX_LOONGSON | DMA_INTR_ENA_RIE | \ + DMA_INTR_ENA_TIE)#define DMA_INTR_NORMAL (DMA_INTR_ENA_NIE | DMA_INTR_ENA_RIE | \ DMA_INTR_ENA_TIE)/* DMA Abnormal interrupt */ +#define DMA_INTR_ENA_AIE_TX_LOONGSON 0x00010000/* Abnormal Loongson Tx Summary */ +#define DMA_INTR_ENA_AIE_RX_LOONGSON 0x00008000/* Abnormal Loongson Rx Summary */ #define DMA_INTR_ENA_AIE 0x00008000/* Abnormal Summary */ #define DMA_INTR_ENA_FBE 0x00002000/* Fatal Bus Error */ #define DMA_INTR_ENA_ETE 0x00000400/* Early Transmit */ @@ -91,10 +98,14 @@#define DMA_INTR_ENA_TJE 0x00000008/* Transmit Jabber */ #define DMA_INTR_ENA_TSE 0x00000002/* Transmit Stopped */ +#define DMA_INTR_ABNORMAL_LOONGSON (DMA_INTR_ENA_AIE_TX_LOONGSON | \ + DMA_INTR_ENA_AIE_RX_LOONGSON | DMA_INTR_ENA_FBE | \ + DMA_INTR_ENA_UNE)#define DMA_INTR_ABNORMAL (DMA_INTR_ENA_AIE | DMA_INTR_ENA_FBE | \ DMA_INTR_ENA_UNE)/* DMA default interrupt mask */ +#define DMA_INTR_DEFAULT_MASK_LOONGSON (DMA_INTR_NORMAL_LOONGSON | DMA_INTR_ABNORMAL_LOONGSON)#define DMA_INTR_DEFAULT_MASK (DMA_INTR_NORMAL | DMA_INTR_ABNORMAL)#define DMA_INTR_DEFAULT_RX (DMA_INTR_ENA_RIE)#define DMA_INTR_DEFAULT_TX (DMA_INTR_ENA_TIE)@@ -111,9 +122,15 @@#define DMA_STATUS_TS_SHIFT 20#define DMA_STATUS_RS_MASK 0x000e0000/* Receive Process State */ #define DMA_STATUS_RS_SHIFT 17 +#define DMA_STATUS_NIS_TX_LOONGSON 0x00040000/* Normal Loongson Tx Interrupt Summary */ +#define DMA_STATUS_NIS_RX_LOONGSON 0x00020000/* Normal Loongson Rx Interrupt Summary */ #define DMA_STATUS_NIS 0x00010000/* Normal Interrupt Summary */ +#define DMA_STATUS_AIS_TX_LOONGSON 0x00010000/* Abnormal Loongson Tx Interrupt Summary */ +#define DMA_STATUS_AIS_RX_LOONGSON 0x00008000/* Abnormal Loongson Rx Interrupt Summary */ #define DMA_STATUS_AIS 0x00008000/* Abnormal Interrupt Summary */ #define DMA_STATUS_ERI 0x00004000/* Early Receive Interrupt */ +#define DMA_STATUS_FBI_TX_LOONGSON 0x00002000/* Fatal Loongson Tx Bus Error Interrupt */ +#define DMA_STATUS_FBI_RX_LOONGSON 0x00001000/* Fatal Loongson Rx Bus Error Interrupt */ #define DMA_STATUS_FBI 0x00002000/* Fatal Bus Error Interrupt */ #define DMA_STATUS_ETI 0x00000400/* Early Transmit Interrupt */ #define DMA_STATUS_RWT 0x00000200/* Receive Watchdog Timeout */ @@ -128,10 +145,21 @@#define DMA_STATUS_TI 0x00000001/* Transmit Interrupt */ #define DMA_CONTROL_FTF 0x00100000/* Flush transmit FIFO */ +#define DMA_STATUS_MSK_COMMON_LOONGSON (DMA_STATUS_NIS_TX_LOONGSON | \ + DMA_STATUS_NIS_RX_LOONGSON | DMA_STATUS_AIS_TX_LOONGSON | \ + DMA_STATUS_AIS_RX_LOONGSON | DMA_STATUS_FBI_TX_LOONGSON | \ + DMA_STATUS_FBI_RX_LOONGSON)#define DMA_STATUS_MSK_COMMON (DMA_STATUS_NIS | \ DMA_STATUS_AIS | \ DMA_STATUS_FBI) +#define DMA_STATUS_MSK_RX_LOONGSON (DMA_STATUS_ERI | \ + DMA_STATUS_RWT | \ + DMA_STATUS_RPS | \ + DMA_STATUS_RU | \ + DMA_STATUS_RI | \ + DMA_STATUS_OVF | \ + DMA_STATUS_MSK_COMMON_LOONGSON)#define DMA_STATUS_MSK_RX (DMA_STATUS_ERI | \ DMA_STATUS_RWT | \ DMA_STATUS_RPS | \@@ -140,6 +168,13 @@ DMA_STATUS_OVF | \ DMA_STATUS_MSK_COMMON) +#define DMA_STATUS_MSK_TX_LOONGSON (DMA_STATUS_ETI | \ + DMA_STATUS_UNF | \ + DMA_STATUS_TJT | \ + DMA_STATUS_TU | \ + DMA_STATUS_TPS | \ + DMA_STATUS_TI | \ + DMA_STATUS_MSK_COMMON_LOONGSON)#define DMA_STATUS_MSK_TX (DMA_STATUS_ETI | \ DMA_STATUS_UNF | \ DMA_STATUS_TJT | \drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +28
-7@@ -167,6 +167,9 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,struct stmmac_txq_stats *txq_stats = &priv->xstats.txq_stats[chan];int ret =0 ;/* read the status register (CSR5) */ +u32 nor_intr_status; +u32 abnor_intr_status; +u32 fb_intr_status;u32 intr_status =readl (ioaddr +DMA_CHAN_STATUS (chan));#ifdef DWMAC_DMA_DEBUG @@ -176,13 +179,31 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,show_rx_process_state (intr_status);#endif -if (dir ==DMA_DIR_RX ) - intr_status &=DMA_STATUS_MSK_RX ; -else if (dir ==DMA_DIR_TX ) - intr_status &=DMA_STATUS_MSK_TX ; +if (priv->plat->flags &STMMAC_FLAG_HAS_LGMAC ) { +if (dir ==DMA_DIR_RX ) + intr_status &=DMA_STATUS_MSK_RX_LOONGSON ; +else if (dir ==DMA_DIR_TX ) + intr_status &=DMA_STATUS_MSK_TX_LOONGSON ; + + nor_intr_status = intr_status & \ + (DMA_STATUS_NIS_TX_LOONGSON |DMA_STATUS_NIS_RX_LOONGSON ); + abnor_intr_status = intr_status & \ + (DMA_STATUS_AIS_TX_LOONGSON |DMA_STATUS_AIS_RX_LOONGSON ); + fb_intr_status = intr_status & \ + (DMA_STATUS_FBI_TX_LOONGSON |DMA_STATUS_FBI_RX_LOONGSON ); + }else { +if (dir ==DMA_DIR_RX ) + intr_status &=DMA_STATUS_MSK_RX ; +else if (dir ==DMA_DIR_TX ) + intr_status &=DMA_STATUS_MSK_TX ; + + nor_intr_status = intr_status &DMA_STATUS_NIS ; + abnor_intr_status = intr_status &DMA_STATUS_AIS ; + fb_intr_status = intr_status &DMA_STATUS_FBI ; + }/* ABNORMAL interrupts */ -if (unlikely (intr_status &DMA_STATUS_AIS )) { +if (unlikely (abnor_intr_status)) {if (unlikely (intr_status &DMA_STATUS_UNF )) { ret = tx_hard_error_bump_tc; x->tx_undeflow_irq++;@@ -205,13 +226,13 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr, x->tx_process_stopped_irq++; ret = tx_hard_error; } -if (unlikely (intr_status &DMA_STATUS_FBI )) { +if (unlikely (intr_status & fb_intr_status)) { x->fatal_bus_error_irq++; ret = tx_hard_error; } }/* TX/RX NORMAL interrupts */ -if (likely (intr_status &DMA_STATUS_NIS )) { +if (likely (nor_intr_status)) {if (likely (intr_status &DMA_STATUS_RI )) {u32 value =readl (ioaddr +DMA_INTR_ENA );/* to schedule NAPI on real RIE event. */ drivers/net/ethernet/stmicro/stmmac/hwif.c +0
-0drivers/net/ethernet/stmicro/stmmac/hwif.c static int stmmac_dwmac1_quirks(struct stmmac_priv *priv) · line 62
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/hwif.c +2
-1@@ -59,7 +59,8 @@ static int stmmac_dwmac1_quirks(struct stmmac_priv *priv)dev_info (priv->device,"Enhanced/Alternate descriptors\n" );/* GMAC older than 3.50 has no extended descriptors */ -if (priv->synopsys_id >=DWMAC_CORE_3_50 ) { +if (priv->synopsys_id >=DWMAC_CORE_3_50 || + priv->synopsys_id ==DWLGMAC_CORE_1_00 ) {This could be left as is if the
priv->synopsys_idfield is overwritten with a correct value (see my last comment).drivers/net/ethernet/stmicro/stmmac/stmmac_main.c static int stmmac_hw_init(struct stmmac_priv *priv) · line 7221
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/hwif.c +0
-0dev_info (priv->device,"Enabled extended descriptors\n" ); priv->extend_desc =1 ; }else {drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +1
-0@@ -7218,6 +7218,7 @@ static int stmmac_hw_init(struct stmmac_priv *priv)* riwt_off field from the platform. */ if (((priv->synopsys_id >= DWMAC_CORE_3_50) || + (priv->synopsys_id == DWLGMAC_CORE_1_00) ||the same comment here.
include/linux/stmmac.h struct dwmac4_addrs { · line 224
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +0
-0(priv->plat->has_xgmac)) && (!priv->plat->riwt_off)) { priv->use_riwt =1 ; dev_info(priv->device,include/linux/stmmac.h +1
-0@@ -221,6 +221,7 @@ struct dwmac4_addrs {#define STMMAC_FLAG_RX_CLK_RUNS_IN_LPI BIT(10)#define STMMAC_FLAG_EN_TX_LPI_CLOCKGATING BIT(11)#define STMMAC_FLAG_HWTSTAMP_CORRECT_LATENCY BIT(12) +#define STMMAC_FLAG_HAS_LGMAC BIT(13)Seeing the patch in the current state would overcomplicate the generic code and the only functions you need to update are
dwmac_dma_interrupt()dwmac1000_dma_init_channel()
you can have these methods re-defined with all the Loongson GNET specifics in the low-level platform driver (dwmac-loongson.c). After that you can just override the mac_device_info.dma pointer with a fixedstmmac_dma_opsdescriptor. Here is what should be done for that:Quoted 4 lines
1. Keep the Patch 4/9 with my comments fixed. First it will be partly useful for your GNET device. Second in general it's a correct implementation of the normal DW GMAC v3.x multi-channels feature and will be useful for the DW GMACs with that feature enabled.
OK.
Quoted 5 lines
2. Create the Loongson GNET-specific
stmmac_dma_ops.dma_interrupt()stmmac_dma_ops.init_chan()
methods in thedwmac-loongson.cdriver. Don't forget to move all the Loongson-specific macros fromdwmac_dma.htodwmac-loongson.c.It's easy.
Quoted 4 lines
3. Create a Loongson GNET-specific platform setup method with the next semantics:
+ allocatestmmac_dma_opsinstance and initialize it withdwmac1000_dma_ops.Do this in
dwmac1000-dma.c? Because this seems impossible to achieve in dwmac-loongson.c:Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c:606:47: error:
initializer element is not constant
606 | const structstmmac_dma_opsdwlgmac_dma_ops=dwmac1000_dma_ops;Quoted 2 lines
+ override the stmmac_dma_ops.{dma_interrupt,
init_chan} with the pointers to the methods defined in 2.Likewise, where should I do this?
Sorry. I seem to have misinterpreted your meaning again.
No worries. Here is what I meant:
1. Declare the private Loongson GMAC data like this:
struct loongson_data { struct stmmac_dma_ops dma_ops; }; 2. Allocate the memory for the data in the framework of the Loongson GMAC device probe() method: loongson_dwmac_probe() { ... ld = devm_kzalloc(&pdev->dev, sizeof(*ld), GFP_KERNEL); if (!ld) return -ENOMEM; ... ld->dma_ops = dwmac1000_dma_ops; ld->dma_ops.init_chan = loongson_gnat_dma_init_chan; ld->dma_ops.dma_interrupt = loongson_gnat_dma_interrupt; ... plat->bsp_priv = ld; }3. Define the Loongson-specific
plat_stmmacenet_data.setup()method, which would re-init thestmmac_priv->synopsys_idwith a correct value, allocate the DW *MAC hardware descriptor and pre-initialize it 'dma' field:
static structmac_device_infoloongson_gnet_setup(void *apriv){ struct stmmac_priv *priv = apriv; struct mac_device_info *mac; struct loongson_data *ld; mac = devm_kzalloc(priv->device, sizeof(*mac), GFP_KERNEL); if (!mac) return NULL; priv->synopsys_id = 0x37; // or whatever is a real version of your IP ld = priv->plat->bsp_priv; mac->dma = &ld->dma_ops; dwmac1000_setup(); // Or Pre-initialize the respective "mac" fields as it's done in dwmac1000_setup() return mac; }4. Make sure the
plat_stmmacenet_data->setupfield is initialized with the Loongson GNAT-specificsetup()method:
static int loongson_gnet_data(structpci_dev*pdev,
structplat_stmmacenet_data*plat){ ... plat->setup = loongson_gnet_setup; ... }
Quoted 8 lines
That shall do what I described in by previous message.
Note another platform which gets to define its own
setup()method Sun8i:drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
although since it fully redefines the DMA-ops descriptor the only common part with your case is that it needs to have thesetup()method too.
This method is great! I have been constantly modifying the code and experimenting
in the past two weeks, but we have too many types of hardware, and some of them
are not working now. I am analyzing the reasons, so I still need some time. :)
Thanks,
Yanteng
Quoted 55 lines
Quoted 14 lines
Quoted 14 lines
+ allocate
mac_device_infoinstance and initialize the mac_device_info.dma field with a pointer to the newstmmac_dma_opsinstance.
+ calldwmac1000_setup()or initializemac_device_infoin a way it's done indwmac1000_setup()(the later might be better so you wouldn't need to export thedwmac1000_setup()function).
+ override stmmac_priv.synopsys_id with a correct value.4. Initialize
plat_stmmacenet_data.setup()with the pointer to the method created in 3.Quoted 8 lines
Quoted 7 lines
If I didn't miss something
stmmac_hwif_init()will call the platform-specific setup method right after fetching the SNPSVER field value. Your setup method will allocatemac_device_infostructure then, will pre-initialize the GNET-specific DMA ops field and fix the Synopsys ID with a proper value (as described in 3 above). The rest of the ops descriptors will be initialized in the loop afterwards based on the specified device ID.This doesn't seem to work because our device looks something like this:
Please see my note above.
Quoted 5 lines
device pci id reversion core version LS7A 0x13 0x00 0x35/0x37 LS7A 0x13 0x01 0x35/0x37 LS2K 0x13 0x00
0x10LS2K 0x13 0x010x10Not sure what you meant by providing this table to me and justifying that something wouldn't work. But it would have been much useful to provide a detailed description of what platforms and devices the current
dwmac-loongson.cdriver supports and what support you are trying to add. Cover-letter is a suitable place for it.In anyway the DW GMAC IP-core can't be
0x10. Seeing your device is having the multi-channels support it must have a version closer to0x37(the highest IP-core version is 3.73a). Please reach the hardware engineers to clarify what actual DW GMAC IP-core has been utilized in your case.-Serge(y)
Quoted 12 lines
Thanks,
Yanteng
Quoted 7 lines
-Serge(y)
Quoted 5 lines
include/linux/stmmac.h +0
-0struct plat_stmmacenet_data {int bus_id;Signature · 1 line
2.31.4
Re: [PATCH net-next v7 5/9] net: stmmac: Add Loongson-specific register definitions
In reply to Serge SeminQuoted 383 lines · Serge Semin
Quoted 320 lines · Yanteng Si
Quoted 35 lines · Serge Semin
Quoted 9 lines · Yanteng Si
There are two types of Loongson DWGMAC. The first type shares the same register definitions and has similar logic as dwmac1000. The second type uses several different register definitions, we think it is necessary to distinguish rx and tx, so we split these bits into two.
Simply put, we split some single bit fields into double bits fileds:
Name Tx Rx
Quoted 7 lines
DMA_INTR_ENA_NIE = 0x00040000 | 0x00020000; DMA_INTR_ENA_AIE = 0x00010000 | 0x00008000; DMA_STATUS_NIS = 0x00040000 | 0x00020000; DMA_STATUS_AIS = 0x00010000 | 0x00008000; DMA_STATUS_FBI = 0x00002000 | 0x00001000;Therefore, when using, TX and RX must be set at the same time.
Thanks for the updated patch. It looks much clearer now. Thanks to that I came up with a better and less invasive solution. See my last comment for details.
Quoted 14 lines
Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- drivers/net/ethernet/stmicro/stmmac/common.h | 1 + .../ethernet/stmicro/stmmac/dwmac-loongson.c | 2 ++ .../ethernet/stmicro/stmmac/dwmac1000_dma.c | 10 ++++-- .../net/ethernet/stmicro/stmmac/dwmac_dma.h | 35 +++++++++++++++++++ .../net/ethernet/stmicro/stmmac/dwmac_lib.c | 35 +++++++++++++++---- drivers/net/ethernet/stmicro/stmmac/hwif.c | 3 +- .../net/ethernet/stmicro/stmmac/stmmac_main.c | 1 + include/linux/stmmac.h | 1 + 8 files changed, 78 insertions(+), 10 deletions(-)Quoted 16 lines
drivers/net/ethernet/stmicro/stmmac/common.h line 37
Quoted 9 lines
drivers/net/ethernet/stmicro/stmmac/common.h +1
-0@@ -34,6 +34,7 @@#define DWMAC_CORE_5_00 0x50#define DWMAC_CORE_5_10 0x51#define DWMAC_CORE_5_20 0x52 +#define DWLGMAC_CORE_1_00 0x10This doesn't look correct because these IDs have been defined for the Synopsys IP-core enumerations. Loongson GNET is definitely based on some DW GMAC v3.x IP-core, but instead of updating the USERVER field vendor just overwrote the GMAC_VERSION.SNPSVER field. From that perspective the correct solution would be to override the
priv->synopsys_idfield with a correct IP-core version (0x37?). See my last comment for details of how to do that.See my last reply.
Quoted 248 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_dwmac_probe(struct pci_dev *pdev, · line 104
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/common.h +0
-0#define DWXGMAC_CORE_2_10 0x21#define DWXGMAC_CORE_2_20 0x22#define DWXLGMAC_CORE_2_00 0x20drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +2
-0@@ -101,6 +101,8 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, plat->mdio_bus_data->needs_reset = true; } + plat->flags |=STMMAC_FLAG_HAS_LGMAC ; +If what I suggest in the last comment is implemented this will be unnecessary.
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +0
-0/* Enable pci device */ ret =pci_enable_device (pdev);if (ret) {drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +0
-0None of the generic parts (
dwmac1000_dma.c,dwmac_dma.h,dwmac_lib.c) will need to be modified if you implement what I suggest in the last comment.drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr,
Quoted 1 line
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +0
-0@@ -118,7 +118,10 @@ static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr,See my comment to patch 4/9. This method can be fully dropped in favor of having the
dwmac1000_dma_init_channel()function implemented.Quoted 175 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +8
-2u32 dma_intr_mask;/* Mask interrupts by writing to CSR7 */ - dma_intr_mask =DMA_INTR_DEFAULT_MASK ; +if (priv->plat->flags &STMMAC_FLAG_HAS_LGMAC ) + dma_intr_mask =DMA_INTR_DEFAULT_MASK_LOONGSON ; +else + dma_intr_mask =DMA_INTR_DEFAULT_MASK ;dma_config (ioaddr +DMA_BUS_MODE , ioaddr +DMA_INTR_ENA , dma_cfg, dma_intr_mask, atds);@@ -130,7 +133,10 @@ static void dwmac1000_dma_init_channel(struct stmmac_priv *priv, void __iomem *iu32 dma_intr_mask;/* Mask interrupts by writing to CSR7 */ - dma_intr_mask =DMA_INTR_DEFAULT_MASK ; +if (priv->plat->flags &STMMAC_FLAG_HAS_LGMAC ) + dma_intr_mask =DMA_INTR_DEFAULT_MASK_LOONGSON ; +else + dma_intr_mask =DMA_INTR_DEFAULT_MASK ;if (dma_cfg->multi_msi_en) dma_config(ioaddr + DMA_CHAN_BUS_MODE(chan),drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +35
-0@@ -70,16 +70,23 @@#define DMA_CONTROL_SR 0x00000002/* Start/Stop Receive */ /* DMA Normal interrupt */ +#define DMA_INTR_ENA_NIE_TX_LOONGSON 0x00040000/* Normal Loongson Tx Summary */ +#define DMA_INTR_ENA_NIE_RX_LOONGSON 0x00020000/* Normal Loongson Rx Summary */ #define DMA_INTR_ENA_NIE 0x00010000/* Normal Summary */ #define DMA_INTR_ENA_TIE 0x00000001/* Transmit Interrupt */ #define DMA_INTR_ENA_TUE 0x00000004/* Transmit Buffer Unavailable */ #define DMA_INTR_ENA_RIE 0x00000040/* Receive Interrupt */ #define DMA_INTR_ENA_ERE 0x00004000/* Early Receive */ +#define DMA_INTR_NORMAL_LOONGSON (DMA_INTR_ENA_NIE_TX_LOONGSON | \ + DMA_INTR_ENA_NIE_RX_LOONGSON | DMA_INTR_ENA_RIE | \ + DMA_INTR_ENA_TIE)#define DMA_INTR_NORMAL (DMA_INTR_ENA_NIE | DMA_INTR_ENA_RIE | \ DMA_INTR_ENA_TIE)/* DMA Abnormal interrupt */ +#define DMA_INTR_ENA_AIE_TX_LOONGSON 0x00010000/* Abnormal Loongson Tx Summary */ +#define DMA_INTR_ENA_AIE_RX_LOONGSON 0x00008000/* Abnormal Loongson Rx Summary */ #define DMA_INTR_ENA_AIE 0x00008000/* Abnormal Summary */ #define DMA_INTR_ENA_FBE 0x00002000/* Fatal Bus Error */ #define DMA_INTR_ENA_ETE 0x00000400/* Early Transmit */ @@ -91,10 +98,14 @@#define DMA_INTR_ENA_TJE 0x00000008/* Transmit Jabber */ #define DMA_INTR_ENA_TSE 0x00000002/* Transmit Stopped */ +#define DMA_INTR_ABNORMAL_LOONGSON (DMA_INTR_ENA_AIE_TX_LOONGSON | \ + DMA_INTR_ENA_AIE_RX_LOONGSON | DMA_INTR_ENA_FBE | \ + DMA_INTR_ENA_UNE)#define DMA_INTR_ABNORMAL (DMA_INTR_ENA_AIE | DMA_INTR_ENA_FBE | \ DMA_INTR_ENA_UNE)/* DMA default interrupt mask */ +#define DMA_INTR_DEFAULT_MASK_LOONGSON (DMA_INTR_NORMAL_LOONGSON | DMA_INTR_ABNORMAL_LOONGSON)#define DMA_INTR_DEFAULT_MASK (DMA_INTR_NORMAL | DMA_INTR_ABNORMAL)#define DMA_INTR_DEFAULT_RX (DMA_INTR_ENA_RIE)#define DMA_INTR_DEFAULT_TX (DMA_INTR_ENA_TIE)@@ -111,9 +122,15 @@#define DMA_STATUS_TS_SHIFT 20#define DMA_STATUS_RS_MASK 0x000e0000/* Receive Process State */ #define DMA_STATUS_RS_SHIFT 17 +#define DMA_STATUS_NIS_TX_LOONGSON 0x00040000/* Normal Loongson Tx Interrupt Summary */ +#define DMA_STATUS_NIS_RX_LOONGSON 0x00020000/* Normal Loongson Rx Interrupt Summary */ #define DMA_STATUS_NIS 0x00010000/* Normal Interrupt Summary */ +#define DMA_STATUS_AIS_TX_LOONGSON 0x00010000/* Abnormal Loongson Tx Interrupt Summary */ +#define DMA_STATUS_AIS_RX_LOONGSON 0x00008000/* Abnormal Loongson Rx Interrupt Summary */ #define DMA_STATUS_AIS 0x00008000/* Abnormal Interrupt Summary */ #define DMA_STATUS_ERI 0x00004000/* Early Receive Interrupt */ +#define DMA_STATUS_FBI_TX_LOONGSON 0x00002000/* Fatal Loongson Tx Bus Error Interrupt */ +#define DMA_STATUS_FBI_RX_LOONGSON 0x00001000/* Fatal Loongson Rx Bus Error Interrupt */ #define DMA_STATUS_FBI 0x00002000/* Fatal Bus Error Interrupt */ #define DMA_STATUS_ETI 0x00000400/* Early Transmit Interrupt */ #define DMA_STATUS_RWT 0x00000200/* Receive Watchdog Timeout */ @@ -128,10 +145,21 @@#define DMA_STATUS_TI 0x00000001/* Transmit Interrupt */ #define DMA_CONTROL_FTF 0x00100000/* Flush transmit FIFO */ +#define DMA_STATUS_MSK_COMMON_LOONGSON (DMA_STATUS_NIS_TX_LOONGSON | \ + DMA_STATUS_NIS_RX_LOONGSON | DMA_STATUS_AIS_TX_LOONGSON | \ + DMA_STATUS_AIS_RX_LOONGSON | DMA_STATUS_FBI_TX_LOONGSON | \ + DMA_STATUS_FBI_RX_LOONGSON)#define DMA_STATUS_MSK_COMMON (DMA_STATUS_NIS | \ DMA_STATUS_AIS | \ DMA_STATUS_FBI) +#define DMA_STATUS_MSK_RX_LOONGSON (DMA_STATUS_ERI | \ + DMA_STATUS_RWT | \ + DMA_STATUS_RPS | \ + DMA_STATUS_RU | \ + DMA_STATUS_RI | \ + DMA_STATUS_OVF | \ + DMA_STATUS_MSK_COMMON_LOONGSON)#define DMA_STATUS_MSK_RX (DMA_STATUS_ERI | \ DMA_STATUS_RWT | \ DMA_STATUS_RPS | \@@ -140,6 +168,13 @@ DMA_STATUS_OVF | \ DMA_STATUS_MSK_COMMON) +#define DMA_STATUS_MSK_TX_LOONGSON (DMA_STATUS_ETI | \ + DMA_STATUS_UNF | \ + DMA_STATUS_TJT | \ + DMA_STATUS_TU | \ + DMA_STATUS_TPS | \ + DMA_STATUS_TI | \ + DMA_STATUS_MSK_COMMON_LOONGSON)#define DMA_STATUS_MSK_TX (DMA_STATUS_ETI | \ DMA_STATUS_UNF | \ DMA_STATUS_TJT | \drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +28
-7@@ -167,6 +167,9 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,struct stmmac_txq_stats *txq_stats = &priv->xstats.txq_stats[chan];int ret =0 ;/* read the status register (CSR5) */ +u32 nor_intr_status; +u32 abnor_intr_status; +u32 fb_intr_status;u32 intr_status =readl (ioaddr +DMA_CHAN_STATUS (chan));#ifdef DWMAC_DMA_DEBUG @@ -176,13 +179,31 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,show_rx_process_state (intr_status);#endif -if (dir ==DMA_DIR_RX ) - intr_status &=DMA_STATUS_MSK_RX ; -else if (dir ==DMA_DIR_TX ) - intr_status &=DMA_STATUS_MSK_TX ; +if (priv->plat->flags &STMMAC_FLAG_HAS_LGMAC ) { +if (dir ==DMA_DIR_RX ) + intr_status &=DMA_STATUS_MSK_RX_LOONGSON ; +else if (dir ==DMA_DIR_TX ) + intr_status &=DMA_STATUS_MSK_TX_LOONGSON ; + + nor_intr_status = intr_status & \ + (DMA_STATUS_NIS_TX_LOONGSON |DMA_STATUS_NIS_RX_LOONGSON ); + abnor_intr_status = intr_status & \ + (DMA_STATUS_AIS_TX_LOONGSON |DMA_STATUS_AIS_RX_LOONGSON ); + fb_intr_status = intr_status & \ + (DMA_STATUS_FBI_TX_LOONGSON |DMA_STATUS_FBI_RX_LOONGSON ); + }else { +if (dir ==DMA_DIR_RX ) + intr_status &=DMA_STATUS_MSK_RX ; +else if (dir ==DMA_DIR_TX ) + intr_status &=DMA_STATUS_MSK_TX ; + + nor_intr_status = intr_status &DMA_STATUS_NIS ; + abnor_intr_status = intr_status &DMA_STATUS_AIS ; + fb_intr_status = intr_status &DMA_STATUS_FBI ; + }/* ABNORMAL interrupts */ -if (unlikely (intr_status &DMA_STATUS_AIS )) { +if (unlikely (abnor_intr_status)) {if (unlikely (intr_status &DMA_STATUS_UNF )) { ret = tx_hard_error_bump_tc; x->tx_undeflow_irq++;@@ -205,13 +226,13 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr, x->tx_process_stopped_irq++; ret = tx_hard_error; } -if (unlikely (intr_status &DMA_STATUS_FBI )) { +if (unlikely (intr_status & fb_intr_status)) { x->fatal_bus_error_irq++; ret = tx_hard_error; } }/* TX/RX NORMAL interrupts */ -if (likely (intr_status &DMA_STATUS_NIS )) { +if (likely (nor_intr_status)) {if (likely (intr_status &DMA_STATUS_RI )) {u32 value =readl (ioaddr +DMA_INTR_ENA );/* to schedule NAPI on real RIE event. */ drivers/net/ethernet/stmicro/stmmac/hwif.c +0
-0drivers/net/ethernet/stmicro/stmmac/hwif.c static int stmmac_dwmac1_quirks(struct stmmac_priv *priv) · line 62
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/hwif.c +2
-1@@ -59,7 +59,8 @@ static int stmmac_dwmac1_quirks(struct stmmac_priv *priv)dev_info (priv->device,"Enhanced/Alternate descriptors\n" );/* GMAC older than 3.50 has no extended descriptors */ -if (priv->synopsys_id >=DWMAC_CORE_3_50 ) { +if (priv->synopsys_id >=DWMAC_CORE_3_50 || + priv->synopsys_id ==DWLGMAC_CORE_1_00 ) {This could be left as is if the
priv->synopsys_idfield is overwritten with a correct value (see my last comment).drivers/net/ethernet/stmicro/stmmac/stmmac_main.c static int stmmac_hw_init(struct stmmac_priv *priv) · line 7221
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/hwif.c +0
-0dev_info (priv->device,"Enabled extended descriptors\n" ); priv->extend_desc =1 ; }else {drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +1
-0@@ -7218,6 +7218,7 @@ static int stmmac_hw_init(struct stmmac_priv *priv)* riwt_off field from the platform. */ if (((priv->synopsys_id >= DWMAC_CORE_3_50) || + (priv->synopsys_id == DWLGMAC_CORE_1_00) ||the same comment here.
include/linux/stmmac.h struct dwmac4_addrs { · line 224
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +0
-0(priv->plat->has_xgmac)) && (!priv->plat->riwt_off)) { priv->use_riwt =1 ; dev_info(priv->device,include/linux/stmmac.h +1
-0@@ -221,6 +221,7 @@ struct dwmac4_addrs {#define STMMAC_FLAG_RX_CLK_RUNS_IN_LPI BIT(10)#define STMMAC_FLAG_EN_TX_LPI_CLOCKGATING BIT(11)#define STMMAC_FLAG_HWTSTAMP_CORRECT_LATENCY BIT(12) +#define STMMAC_FLAG_HAS_LGMAC BIT(13)Seeing the patch in the current state would overcomplicate the generic code and the only functions you need to update are
dwmac_dma_interrupt()dwmac1000_dma_init_channel()
you can have these methods re-defined with all the Loongson GNET specifics in the low-level platform driver (dwmac-loongson.c). After that you can just override the mac_device_info.dma pointer with a fixedstmmac_dma_opsdescriptor. Here is what should be done for that:Quoted 4 lines
1. Keep the Patch 4/9 with my comments fixed. First it will be partly useful for your GNET device. Second in general it's a correct implementation of the normal DW GMAC v3.x multi-channels feature and will be useful for the DW GMACs with that feature enabled.
OK.
Quoted 5 lines
2. Create the Loongson GNET-specific
stmmac_dma_ops.dma_interrupt()stmmac_dma_ops.init_chan()
methods in thedwmac-loongson.cdriver. Don't forget to move all the Loongson-specific macros fromdwmac_dma.htodwmac-loongson.c.It's easy.
Quoted 4 lines
3. Create a Loongson GNET-specific platform setup method with the next semantics:
+ allocatestmmac_dma_opsinstance and initialize it withdwmac1000_dma_ops.Do this in
dwmac1000-dma.c? Because this seems impossible to achieve in dwmac-loongson.c:Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c:606:47: error:
initializer element is not constant
606 | const structstmmac_dma_opsdwlgmac_dma_ops=dwmac1000_dma_ops;Quoted 2 lines
+ override the stmmac_dma_ops.{dma_interrupt,
init_chan} with the pointers to the methods defined in 2.Likewise, where should I do this?
Sorry. I seem to have misinterpreted your meaning again.
No worries. Here is what I meant:
1. Declare the private Loongson GMAC data like this:
struct loongson_data { struct stmmac_dma_ops dma_ops; }; 2. Allocate the memory for the data in the framework of the Loongson GMAC device probe() method: loongson_dwmac_probe() { ... ld = devm_kzalloc(&pdev->dev, sizeof(*ld), GFP_KERNEL); if (!ld) return -ENOMEM; ... ld->dma_ops = dwmac1000_dma_ops; ld->dma_ops.init_chan = loongson_gnat_dma_init_chan; ld->dma_ops.dma_interrupt = loongson_gnat_dma_interrupt; ... plat->bsp_priv = ld; }3. Define the Loongson-specific
plat_stmmacenet_data.setup()method, which would re-init thestmmac_priv->synopsys_idwith a correct value, allocate the DW *MAC hardware descriptor and pre-initialize it 'dma' field:
static structmac_device_infoloongson_gnet_setup(void *apriv){ struct stmmac_priv *priv = apriv; struct mac_device_info *mac; struct loongson_data *ld; mac = devm_kzalloc(priv->device, sizeof(*mac), GFP_KERNEL); if (!mac) return NULL; priv->synopsys_id = 0x37; // or whatever is a real version of your IP ld = priv->plat->bsp_priv; mac->dma = &ld->dma_ops; dwmac1000_setup(); // Or Pre-initialize the respective "mac" fields as it's done in dwmac1000_setup() return mac; }4. Make sure the
plat_stmmacenet_data->setupfield is initialized with the Loongson GNAT-specificsetup()method:
static int loongson_gnet_data(structpci_dev*pdev,
structplat_stmmacenet_data*plat){ ... plat->setup = loongson_gnet_setup; ... }
Quoted 8 lines
That shall do what I described in by previous message.
Note another platform which gets to define its own
setup()method Sun8i:drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
although since it fully redefines the DMA-ops descriptor the only common part with your case is that it needs to have thesetup()method too.
Thank you so much, this method is so cool!
After three weeks of hard work, everything is working now. I will reply to your other comments tomorrow.
Thanks,
Yanteng
Quoted 54 lines
Quoted 13 lines
Quoted 13 lines
+ allocate
mac_device_infoinstance and initialize the mac_device_info.dma field with a pointer to the newstmmac_dma_opsinstance.
+ calldwmac1000_setup()or initializemac_device_infoin a way it's done indwmac1000_setup()(the later might be better so you wouldn't need to export thedwmac1000_setup()function).
+ override stmmac_priv.synopsys_id with a correct value.4. Initialize
plat_stmmacenet_data.setup()with the pointer to the method created in 3.Quoted 8 lines
Quoted 7 lines
If I didn't miss something
stmmac_hwif_init()will call the platform-specific setup method right after fetching the SNPSVER field value. Your setup method will allocatemac_device_infostructure then, will pre-initialize the GNET-specific DMA ops field and fix the Synopsys ID with a proper value (as described in 3 above). The rest of the ops descriptors will be initialized in the loop afterwards based on the specified device ID.This doesn't seem to work because our device looks something like this:
Please see my note above.
Quoted 5 lines
device pci id reversion core version LS7A 0x13 0x00 0x35/0x37 LS7A 0x13 0x01 0x35/0x37 LS2K 0x13 0x00
0x10LS2K 0x13 0x010x10Not sure what you meant by providing this table to me and justifying that something wouldn't work. But it would have been much useful to provide a detailed description of what platforms and devices the current
dwmac-loongson.cdriver supports and what support you are trying to add. Cover-letter is a suitable place for it.In anyway the DW GMAC IP-core can't be
0x10. Seeing your device is having the multi-channels support it must have a version closer to0x37(the highest IP-core version is 3.73a). Please reach the hardware engineers to clarify what actual DW GMAC IP-core has been utilized in your case.-Serge(y)
Quoted 12 lines
Thanks,
Yanteng
Quoted 7 lines
-Serge(y)
Quoted 5 lines
include/linux/stmmac.h +0
-0struct plat_stmmacenet_data {int bus_id;Signature · 1 line
2.31.4
Re: [PATCH net-next v7 5/9] net: stmmac: Add Loongson-specific register definitions
Quoted 395 lines · Yanteng Si
Quoted 383 lines · Serge Semin
Quoted 320 lines · Yanteng Si
Quoted 35 lines · Serge Semin
Quoted 9 lines · Yanteng Si
There are two types of Loongson DWGMAC. The first type shares the same register definitions and has similar logic as dwmac1000. The second type uses several different register definitions, we think it is necessary to distinguish rx and tx, so we split these bits into two.
Simply put, we split some single bit fields into double bits fileds:
Name Tx Rx
Quoted 7 lines
DMA_INTR_ENA_NIE = 0x00040000 | 0x00020000; DMA_INTR_ENA_AIE = 0x00010000 | 0x00008000; DMA_STATUS_NIS = 0x00040000 | 0x00020000; DMA_STATUS_AIS = 0x00010000 | 0x00008000; DMA_STATUS_FBI = 0x00002000 | 0x00001000;Therefore, when using, TX and RX must be set at the same time.
Thanks for the updated patch. It looks much clearer now. Thanks to that I came up with a better and less invasive solution. See my last comment for details.
Quoted 14 lines
Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- drivers/net/ethernet/stmicro/stmmac/common.h | 1 + .../ethernet/stmicro/stmmac/dwmac-loongson.c | 2 ++ .../ethernet/stmicro/stmmac/dwmac1000_dma.c | 10 ++++-- .../net/ethernet/stmicro/stmmac/dwmac_dma.h | 35 +++++++++++++++++++ .../net/ethernet/stmicro/stmmac/dwmac_lib.c | 35 +++++++++++++++---- drivers/net/ethernet/stmicro/stmmac/hwif.c | 3 +- .../net/ethernet/stmicro/stmmac/stmmac_main.c | 1 + include/linux/stmmac.h | 1 + 8 files changed, 78 insertions(+), 10 deletions(-)Quoted 16 lines
drivers/net/ethernet/stmicro/stmmac/common.h line 37
Quoted 9 lines
drivers/net/ethernet/stmicro/stmmac/common.h +1
-0@@ -34,6 +34,7 @@#define DWMAC_CORE_5_00 0x50#define DWMAC_CORE_5_10 0x51#define DWMAC_CORE_5_20 0x52 +#define DWLGMAC_CORE_1_00 0x10This doesn't look correct because these IDs have been defined for the Synopsys IP-core enumerations. Loongson GNET is definitely based on some DW GMAC v3.x IP-core, but instead of updating the USERVER field vendor just overwrote the GMAC_VERSION.SNPSVER field. From that perspective the correct solution would be to override the
priv->synopsys_idfield with a correct IP-core version (0x37?). See my last comment for details of how to do that.See my last reply.
Quoted 248 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_dwmac_probe(struct pci_dev *pdev, · line 104
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/common.h +0
-0#define DWXGMAC_CORE_2_10 0x21#define DWXGMAC_CORE_2_20 0x22#define DWXLGMAC_CORE_2_00 0x20drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +2
-0@@ -101,6 +101,8 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, plat->mdio_bus_data->needs_reset = true; } + plat->flags |=STMMAC_FLAG_HAS_LGMAC ; +If what I suggest in the last comment is implemented this will be unnecessary.
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +0
-0/* Enable pci device */ ret =pci_enable_device (pdev);if (ret) {drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +0
-0None of the generic parts (
dwmac1000_dma.c,dwmac_dma.h,dwmac_lib.c) will need to be modified if you implement what I suggest in the last comment.drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr,
Quoted 1 line
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +0
-0@@ -118,7 +118,10 @@ static void dwmac1000_dma_init(struct stmmac_priv *priv, void __iomem *ioaddr,See my comment to patch 4/9. This method can be fully dropped in favor of having the
dwmac1000_dma_init_channel()function implemented.Quoted 175 lines
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +8
-2u32 dma_intr_mask;/* Mask interrupts by writing to CSR7 */ - dma_intr_mask =DMA_INTR_DEFAULT_MASK ; +if (priv->plat->flags &STMMAC_FLAG_HAS_LGMAC ) + dma_intr_mask =DMA_INTR_DEFAULT_MASK_LOONGSON ; +else + dma_intr_mask =DMA_INTR_DEFAULT_MASK ;dma_config (ioaddr +DMA_BUS_MODE , ioaddr +DMA_INTR_ENA , dma_cfg, dma_intr_mask, atds);@@ -130,7 +133,10 @@ static void dwmac1000_dma_init_channel(struct stmmac_priv *priv, void __iomem *iu32 dma_intr_mask;/* Mask interrupts by writing to CSR7 */ - dma_intr_mask =DMA_INTR_DEFAULT_MASK ; +if (priv->plat->flags &STMMAC_FLAG_HAS_LGMAC ) + dma_intr_mask =DMA_INTR_DEFAULT_MASK_LOONGSON ; +else + dma_intr_mask =DMA_INTR_DEFAULT_MASK ;if (dma_cfg->multi_msi_en) dma_config(ioaddr + DMA_CHAN_BUS_MODE(chan),drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +35
-0@@ -70,16 +70,23 @@#define DMA_CONTROL_SR 0x00000002/* Start/Stop Receive */ /* DMA Normal interrupt */ +#define DMA_INTR_ENA_NIE_TX_LOONGSON 0x00040000/* Normal Loongson Tx Summary */ +#define DMA_INTR_ENA_NIE_RX_LOONGSON 0x00020000/* Normal Loongson Rx Summary */ #define DMA_INTR_ENA_NIE 0x00010000/* Normal Summary */ #define DMA_INTR_ENA_TIE 0x00000001/* Transmit Interrupt */ #define DMA_INTR_ENA_TUE 0x00000004/* Transmit Buffer Unavailable */ #define DMA_INTR_ENA_RIE 0x00000040/* Receive Interrupt */ #define DMA_INTR_ENA_ERE 0x00004000/* Early Receive */ +#define DMA_INTR_NORMAL_LOONGSON (DMA_INTR_ENA_NIE_TX_LOONGSON | \ + DMA_INTR_ENA_NIE_RX_LOONGSON | DMA_INTR_ENA_RIE | \ + DMA_INTR_ENA_TIE)#define DMA_INTR_NORMAL (DMA_INTR_ENA_NIE | DMA_INTR_ENA_RIE | \ DMA_INTR_ENA_TIE)/* DMA Abnormal interrupt */ +#define DMA_INTR_ENA_AIE_TX_LOONGSON 0x00010000/* Abnormal Loongson Tx Summary */ +#define DMA_INTR_ENA_AIE_RX_LOONGSON 0x00008000/* Abnormal Loongson Rx Summary */ #define DMA_INTR_ENA_AIE 0x00008000/* Abnormal Summary */ #define DMA_INTR_ENA_FBE 0x00002000/* Fatal Bus Error */ #define DMA_INTR_ENA_ETE 0x00000400/* Early Transmit */ @@ -91,10 +98,14 @@#define DMA_INTR_ENA_TJE 0x00000008/* Transmit Jabber */ #define DMA_INTR_ENA_TSE 0x00000002/* Transmit Stopped */ +#define DMA_INTR_ABNORMAL_LOONGSON (DMA_INTR_ENA_AIE_TX_LOONGSON | \ + DMA_INTR_ENA_AIE_RX_LOONGSON | DMA_INTR_ENA_FBE | \ + DMA_INTR_ENA_UNE)#define DMA_INTR_ABNORMAL (DMA_INTR_ENA_AIE | DMA_INTR_ENA_FBE | \ DMA_INTR_ENA_UNE)/* DMA default interrupt mask */ +#define DMA_INTR_DEFAULT_MASK_LOONGSON (DMA_INTR_NORMAL_LOONGSON | DMA_INTR_ABNORMAL_LOONGSON)#define DMA_INTR_DEFAULT_MASK (DMA_INTR_NORMAL | DMA_INTR_ABNORMAL)#define DMA_INTR_DEFAULT_RX (DMA_INTR_ENA_RIE)#define DMA_INTR_DEFAULT_TX (DMA_INTR_ENA_TIE)@@ -111,9 +122,15 @@#define DMA_STATUS_TS_SHIFT 20#define DMA_STATUS_RS_MASK 0x000e0000/* Receive Process State */ #define DMA_STATUS_RS_SHIFT 17 +#define DMA_STATUS_NIS_TX_LOONGSON 0x00040000/* Normal Loongson Tx Interrupt Summary */ +#define DMA_STATUS_NIS_RX_LOONGSON 0x00020000/* Normal Loongson Rx Interrupt Summary */ #define DMA_STATUS_NIS 0x00010000/* Normal Interrupt Summary */ +#define DMA_STATUS_AIS_TX_LOONGSON 0x00010000/* Abnormal Loongson Tx Interrupt Summary */ +#define DMA_STATUS_AIS_RX_LOONGSON 0x00008000/* Abnormal Loongson Rx Interrupt Summary */ #define DMA_STATUS_AIS 0x00008000/* Abnormal Interrupt Summary */ #define DMA_STATUS_ERI 0x00004000/* Early Receive Interrupt */ +#define DMA_STATUS_FBI_TX_LOONGSON 0x00002000/* Fatal Loongson Tx Bus Error Interrupt */ +#define DMA_STATUS_FBI_RX_LOONGSON 0x00001000/* Fatal Loongson Rx Bus Error Interrupt */ #define DMA_STATUS_FBI 0x00002000/* Fatal Bus Error Interrupt */ #define DMA_STATUS_ETI 0x00000400/* Early Transmit Interrupt */ #define DMA_STATUS_RWT 0x00000200/* Receive Watchdog Timeout */ @@ -128,10 +145,21 @@#define DMA_STATUS_TI 0x00000001/* Transmit Interrupt */ #define DMA_CONTROL_FTF 0x00100000/* Flush transmit FIFO */ +#define DMA_STATUS_MSK_COMMON_LOONGSON (DMA_STATUS_NIS_TX_LOONGSON | \ + DMA_STATUS_NIS_RX_LOONGSON | DMA_STATUS_AIS_TX_LOONGSON | \ + DMA_STATUS_AIS_RX_LOONGSON | DMA_STATUS_FBI_TX_LOONGSON | \ + DMA_STATUS_FBI_RX_LOONGSON)#define DMA_STATUS_MSK_COMMON (DMA_STATUS_NIS | \ DMA_STATUS_AIS | \ DMA_STATUS_FBI) +#define DMA_STATUS_MSK_RX_LOONGSON (DMA_STATUS_ERI | \ + DMA_STATUS_RWT | \ + DMA_STATUS_RPS | \ + DMA_STATUS_RU | \ + DMA_STATUS_RI | \ + DMA_STATUS_OVF | \ + DMA_STATUS_MSK_COMMON_LOONGSON)#define DMA_STATUS_MSK_RX (DMA_STATUS_ERI | \ DMA_STATUS_RWT | \ DMA_STATUS_RPS | \@@ -140,6 +168,13 @@ DMA_STATUS_OVF | \ DMA_STATUS_MSK_COMMON) +#define DMA_STATUS_MSK_TX_LOONGSON (DMA_STATUS_ETI | \ + DMA_STATUS_UNF | \ + DMA_STATUS_TJT | \ + DMA_STATUS_TU | \ + DMA_STATUS_TPS | \ + DMA_STATUS_TI | \ + DMA_STATUS_MSK_COMMON_LOONGSON)#define DMA_STATUS_MSK_TX (DMA_STATUS_ETI | \ DMA_STATUS_UNF | \ DMA_STATUS_TJT | \drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +28
-7@@ -167,6 +167,9 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,struct stmmac_txq_stats *txq_stats = &priv->xstats.txq_stats[chan];int ret =0 ;/* read the status register (CSR5) */ +u32 nor_intr_status; +u32 abnor_intr_status; +u32 fb_intr_status;u32 intr_status =readl (ioaddr +DMA_CHAN_STATUS (chan));#ifdef DWMAC_DMA_DEBUG @@ -176,13 +179,31 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,show_rx_process_state (intr_status);#endif -if (dir ==DMA_DIR_RX ) - intr_status &=DMA_STATUS_MSK_RX ; -else if (dir ==DMA_DIR_TX ) - intr_status &=DMA_STATUS_MSK_TX ; +if (priv->plat->flags &STMMAC_FLAG_HAS_LGMAC ) { +if (dir ==DMA_DIR_RX ) + intr_status &=DMA_STATUS_MSK_RX_LOONGSON ; +else if (dir ==DMA_DIR_TX ) + intr_status &=DMA_STATUS_MSK_TX_LOONGSON ; + + nor_intr_status = intr_status & \ + (DMA_STATUS_NIS_TX_LOONGSON |DMA_STATUS_NIS_RX_LOONGSON ); + abnor_intr_status = intr_status & \ + (DMA_STATUS_AIS_TX_LOONGSON |DMA_STATUS_AIS_RX_LOONGSON ); + fb_intr_status = intr_status & \ + (DMA_STATUS_FBI_TX_LOONGSON |DMA_STATUS_FBI_RX_LOONGSON ); + }else { +if (dir ==DMA_DIR_RX ) + intr_status &=DMA_STATUS_MSK_RX ; +else if (dir ==DMA_DIR_TX ) + intr_status &=DMA_STATUS_MSK_TX ; + + nor_intr_status = intr_status &DMA_STATUS_NIS ; + abnor_intr_status = intr_status &DMA_STATUS_AIS ; + fb_intr_status = intr_status &DMA_STATUS_FBI ; + }/* ABNORMAL interrupts */ -if (unlikely (intr_status &DMA_STATUS_AIS )) { +if (unlikely (abnor_intr_status)) {if (unlikely (intr_status &DMA_STATUS_UNF )) { ret = tx_hard_error_bump_tc; x->tx_undeflow_irq++;@@ -205,13 +226,13 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr, x->tx_process_stopped_irq++; ret = tx_hard_error; } -if (unlikely (intr_status &DMA_STATUS_FBI )) { +if (unlikely (intr_status & fb_intr_status)) { x->fatal_bus_error_irq++; ret = tx_hard_error; } }/* TX/RX NORMAL interrupts */ -if (likely (intr_status &DMA_STATUS_NIS )) { +if (likely (nor_intr_status)) {if (likely (intr_status &DMA_STATUS_RI )) {u32 value =readl (ioaddr +DMA_INTR_ENA );/* to schedule NAPI on real RIE event. */ drivers/net/ethernet/stmicro/stmmac/hwif.c +0
-0drivers/net/ethernet/stmicro/stmmac/hwif.c static int stmmac_dwmac1_quirks(struct stmmac_priv *priv) · line 62
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/hwif.c +2
-1@@ -59,7 +59,8 @@ static int stmmac_dwmac1_quirks(struct stmmac_priv *priv)dev_info (priv->device,"Enhanced/Alternate descriptors\n" );/* GMAC older than 3.50 has no extended descriptors */ -if (priv->synopsys_id >=DWMAC_CORE_3_50 ) { +if (priv->synopsys_id >=DWMAC_CORE_3_50 || + priv->synopsys_id ==DWLGMAC_CORE_1_00 ) {This could be left as is if the
priv->synopsys_idfield is overwritten with a correct value (see my last comment).drivers/net/ethernet/stmicro/stmmac/stmmac_main.c static int stmmac_hw_init(struct stmmac_priv *priv) · line 7221
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/hwif.c +0
-0dev_info (priv->device,"Enabled extended descriptors\n" ); priv->extend_desc =1 ; }else {drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +1
-0@@ -7218,6 +7218,7 @@ static int stmmac_hw_init(struct stmmac_priv *priv)* riwt_off field from the platform. */ if (((priv->synopsys_id >= DWMAC_CORE_3_50) || + (priv->synopsys_id == DWLGMAC_CORE_1_00) ||the same comment here.
include/linux/stmmac.h struct dwmac4_addrs { · line 224
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +0
-0(priv->plat->has_xgmac)) && (!priv->plat->riwt_off)) { priv->use_riwt =1 ; dev_info(priv->device,include/linux/stmmac.h +1
-0@@ -221,6 +221,7 @@ struct dwmac4_addrs {#define STMMAC_FLAG_RX_CLK_RUNS_IN_LPI BIT(10)#define STMMAC_FLAG_EN_TX_LPI_CLOCKGATING BIT(11)#define STMMAC_FLAG_HWTSTAMP_CORRECT_LATENCY BIT(12) +#define STMMAC_FLAG_HAS_LGMAC BIT(13)Seeing the patch in the current state would overcomplicate the generic code and the only functions you need to update are
dwmac_dma_interrupt()dwmac1000_dma_init_channel()
you can have these methods re-defined with all the Loongson GNET specifics in the low-level platform driver (dwmac-loongson.c). After that you can just override the mac_device_info.dma pointer with a fixedstmmac_dma_opsdescriptor. Here is what should be done for that:Quoted 4 lines
1. Keep the Patch 4/9 with my comments fixed. First it will be partly useful for your GNET device. Second in general it's a correct implementation of the normal DW GMAC v3.x multi-channels feature and will be useful for the DW GMACs with that feature enabled.
OK.
Quoted 5 lines
2. Create the Loongson GNET-specific
stmmac_dma_ops.dma_interrupt()stmmac_dma_ops.init_chan()
methods in thedwmac-loongson.cdriver. Don't forget to move all the Loongson-specific macros fromdwmac_dma.htodwmac-loongson.c.It's easy.
Quoted 4 lines
3. Create a Loongson GNET-specific platform setup method with the next semantics:
+ allocatestmmac_dma_opsinstance and initialize it withdwmac1000_dma_ops.Do this in
dwmac1000-dma.c? Because this seems impossible to achieve in dwmac-loongson.c:Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c:606:47: error:
initializer element is not constant
606 | const structstmmac_dma_opsdwlgmac_dma_ops=dwmac1000_dma_ops;Quoted 2 lines
+ override the stmmac_dma_ops.{dma_interrupt,
init_chan} with the pointers to the methods defined in 2.Likewise, where should I do this?
Sorry. I seem to have misinterpreted your meaning again.
No worries. Here is what I meant:
1. Declare the private Loongson GMAC data like this:
struct loongson_data { struct stmmac_dma_ops dma_ops; }; 2. Allocate the memory for the data in the framework of the Loongson GMAC device probe() method: loongson_dwmac_probe() { ... ld = devm_kzalloc(&pdev->dev, sizeof(*ld), GFP_KERNEL); if (!ld) return -ENOMEM; ... ld->dma_ops = dwmac1000_dma_ops; ld->dma_ops.init_chan = loongson_gnat_dma_init_chan; ld->dma_ops.dma_interrupt = loongson_gnat_dma_interrupt; ... plat->bsp_priv = ld; }3. Define the Loongson-specific
plat_stmmacenet_data.setup()method, which would re-init thestmmac_priv->synopsys_idwith a correct value, allocate the DW *MAC hardware descriptor and pre-initialize it 'dma' field:
static structmac_device_infoloongson_gnet_setup(void *apriv){ struct stmmac_priv *priv = apriv; struct mac_device_info *mac; struct loongson_data *ld; mac = devm_kzalloc(priv->device, sizeof(*mac), GFP_KERNEL); if (!mac) return NULL; priv->synopsys_id = 0x37; // or whatever is a real version of your IP ld = priv->plat->bsp_priv; mac->dma = &ld->dma_ops; dwmac1000_setup(); // Or Pre-initialize the respective "mac" fields as it's done in dwmac1000_setup() return mac; }4. Make sure the
plat_stmmacenet_data->setupfield is initialized with the Loongson GNAT-specificsetup()method:
static int loongson_gnet_data(structpci_dev*pdev,
structplat_stmmacenet_data*plat){ ... plat->setup = loongson_gnet_setup; ... }Quoted 8 lines
That shall do what I described in by previous message.
Note another platform which gets to define its own
setup()method Sun8i:drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
although since it fully redefines the DMA-ops descriptor the only common part with your case is that it needs to have thesetup()method too.
Quoted 3 lines
Thank you so much, this method is so cool!
After three weeks of hard work, everything is working now.
Glad my advice could help. Let's see what is done in v8.
* Although I'll be able to get back to review on the next week only.
-Serge(y)
Quoted 63 lines
I will reply to
your other comments tomorrow.Thanks,
Yanteng
Quoted 54 lines
Quoted 13 lines
Quoted 13 lines
+ allocate
mac_device_infoinstance and initialize the mac_device_info.dma field with a pointer to the newstmmac_dma_opsinstance.
+ calldwmac1000_setup()or initializemac_device_infoin a way it's done indwmac1000_setup()(the later might be better so you wouldn't need to export thedwmac1000_setup()function).
+ override stmmac_priv.synopsys_id with a correct value.4. Initialize
plat_stmmacenet_data.setup()with the pointer to the method created in 3.Quoted 8 lines
Quoted 7 lines
If I didn't miss something
stmmac_hwif_init()will call the platform-specific setup method right after fetching the SNPSVER field value. Your setup method will allocatemac_device_infostructure then, will pre-initialize the GNET-specific DMA ops field and fix the Synopsys ID with a proper value (as described in 3 above). The rest of the ops descriptors will be initialized in the loop afterwards based on the specified device ID.This doesn't seem to work because our device looks something like this:
Please see my note above.
Quoted 5 lines
device pci id reversion core version LS7A 0x13 0x00 0x35/0x37 LS7A 0x13 0x01 0x35/0x37 LS2K 0x13 0x00
0x10LS2K 0x13 0x010x10Not sure what you meant by providing this table to me and justifying that something wouldn't work. But it would have been much useful to provide a detailed description of what platforms and devices the current
dwmac-loongson.cdriver supports and what support you are trying to add. Cover-letter is a suitable place for it.In anyway the DW GMAC IP-core can't be
0x10. Seeing your device is having the multi-channels support it must have a version closer to0x37(the highest IP-core version is 3.73a). Please reach the hardware engineers to clarify what actual DW GMAC IP-core has been utilized in your case.-Serge(y)
Quoted 12 lines
Thanks,
Yanteng
Quoted 7 lines
-Serge(y)
Quoted 5 lines
include/linux/stmmac.h +0
-0struct plat_stmmacenet_data {int bus_id;Signature · 1 line
2.31.4
PATCH v7 6/9 net: stmmac: dwmac-loongson: Add MSI support
In reply to Yanteng SiRequest allocation for MSI for specific versions.
Some features of Loongson platforms are bound to the GMAC_VERSION register. We have to read its value in order to get the correct channel number.
--- .../ethernet/stmicro/stmmac/dwmac-loongson.c | 132 ++++++++++++++---- 1 file changed, 102 insertions(+), 30 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +102 -30
@@ -11,8 +11,85 @@struct stmmac_pci_info {int (*setup)(struct pci_dev *pdev,struct plat_stmmacenet_data *plat); +int (*config)(struct pci_dev *pdev,struct plat_stmmacenet_data *plat, +struct stmmac_resources *res,struct device_node *np); }; +static int loongson_dwmac_config_legacy (struct pci_dev *pdev, +struct plat_stmmacenet_data *plat, +struct stmmac_resources *res, +struct device_node *np) +{ +if (np) { + res->irq =of_irq_get_byname (np,"macirq" ); +if (res->irq <0 ) { +dev_err (&pdev->dev,"IRQ macirq not found\n" ); +return -ENODEV ; + } + + res->wol_irq =of_irq_get_byname (np,"eth_wake_irq" ); +if (res->wol_irq <0 ) { +dev_info (&pdev->dev, +"IRQ eth_wake_irq not found, using macirq\n" ); + res->wol_irq = res->irq; + } + + res->lpi_irq =of_irq_get_byname (np,"eth_lpi" ); +if (res->lpi_irq <0 ) { +dev_err (&pdev->dev,"IRQ eth_lpi not found\n" ); +return -ENODEV ; + } + }else { + res->irq = pdev->irq; + res->wol_irq = res->irq; + } + + plat->flags &= ~STMMAC_FLAG_MULTI_MSI_EN ; +dev_info (&pdev->dev,"%s: Single IRQ enablement successful\n" , + __func__); + +return 0 ; +} + +static int loongson_dwmac_config_multi_msi (struct pci_dev *pdev, +struct plat_stmmacenet_data *plat, +struct stmmac_resources *res, +struct device_node *np, +int channel_num) +{ +int i, ret, vecs; + + vecs =roundup_pow_of_two (channel_num *2 +1 ); + ret =pci_alloc_irq_vectors (pdev, vecs, vecs,PCI_IRQ_MSI ); +if (ret <0 ) { +dev_info (&pdev->dev, +"MSI enable failed, Fallback to legacy interrupt\n" ); +return loongson_dwmac_config_legacy (pdev, plat, res, np); + } + + plat->rx_queues_to_use = channel_num; + plat->tx_queues_to_use = channel_num; + + res->irq =pci_irq_vector (pdev,0 ); + res->wol_irq = res->irq; + +/* INT NAME | MAC | CH7 rx | CH7 tx | ... | CH0 rx | CH0 tx | +* --------- ----- -------- -------- ... -------- -------- +* IRQ NUM | 0 | 1 | 2 | ... | 15 | 16 | +*/ +for (i =0 ; i < channel_num; i++) { + res->rx_irq[channel_num -1 - i] = +pci_irq_vector (pdev,1 + i *2 ); + res->tx_irq[channel_num -1 - i] = +pci_irq_vector (pdev,2 + i *2 ); + } + + plat->flags |=STMMAC_FLAG_MULTI_MSI_EN ; +dev_info (&pdev->dev,"%s: multi MSI enablement successful\n" , __func__); + +return 0 ; +} +static void loongson_default_data (struct pci_dev *pdev,struct plat_stmmacenet_data *plat) {
@@ -66,8 +143,29 @@ static int loongson_gmac_data(struct pci_dev *pdev,return 0 ; } +static int loongson_gmac_config (struct pci_dev *pdev, +struct plat_stmmacenet_data *plat, +struct stmmac_resources *res, +struct device_node *np) +{ +int ret; +u32 version =readl (res->addr +GMAC_VERSION ); + +switch (version &0xff ) { +case DWLGMAC_CORE_1_00 : + ret =loongson_dwmac_config_multi_msi (pdev, plat, res, np,8 ); +break ; +default : + ret =loongson_dwmac_config_legacy (pdev, plat, res, np); +break ; + } + +return ret; +} +static struct stmmac_pci_info loongson_gmac_pci_info = { .setup = loongson_gmac_data, + .config = loongson_gmac_config, }; static int loongson_dwmac_probe(struct pci_dev *pdev,
@@ -142,44 +240,19 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, plat->phy_interface = phy_mode; } -pci_enable_msi (pdev);memset (&res,0 ,sizeof (res)); res.addr =pcim_iomap_table (pdev)[0 ]; -if (np) { - res.irq =of_irq_get_byname (np,"macirq" ); -if (res.irq <0 ) { -dev_err (&pdev->dev,"IRQ macirq not found\n" ); - ret = -ENODEV ; - goto err_disable_msi; - } - - res.wol_irq =of_irq_get_byname (np,"eth_wake_irq" ); -if (res.wol_irq <0 ) { -dev_info (&pdev->dev, -"IRQ eth_wake_irq not found, using macirq\n" ); - res.wol_irq = res.irq; - } - - res.lpi_irq =of_irq_get_byname (np,"eth_lpi" ); -if (res.lpi_irq <0 ) { -dev_err (&pdev->dev,"IRQ eth_lpi not found\n" ); - ret = -ENODEV ; - goto err_disable_msi; - } - }else { - res.irq = pdev->irq; - res.wol_irq = pdev->irq; - } + ret = info->config (pdev, plat, &res, np); +if (ret) + goto err_disable_device; ret =stmmac_dvr_probe (&pdev->dev, plat, &res);if (ret) - goto err_disable_msi; + goto err_disable_device;return ret; -err_disable_msi: -pci_disable_msi (pdev); err_disable_device:pci_disable_device (pdev); err_put_node:
@@ -203,7 +276,6 @@ static void loongson_dwmac_remove(struct pci_dev *pdev)break ; } -pci_disable_msi (pdev);pci_disable_device (pdev); }
Signature · 1 line
2.31.4
PATCH v7 7/9 net: stmmac: dwmac-loongson: Add GNET support
In reply to Yanteng SiAdd Loongson GNET (GMAC with PHY) support. Current GNET does not support half duplex mode, and GNET on LS7A only supports ANE when speed is set to 1000M.
--- .../ethernet/stmicro/stmmac/dwmac-loongson.c | 79 +++++++++++++++++++ .../ethernet/stmicro/stmmac/stmmac_ethtool.c | 6 ++ include/linux/stmmac.h | 2 + 3 files changed, 87 insertions(+)
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +79 -0
@@ -168,6 +168,83 @@ static struct stmmac_pci_info loongson_gmac_pci_info = { .config = loongson_gmac_config, }; +static void loongson_gnet_fix_speed (void *priv,unsigned int speed,unsigned int mode) +{ +struct net_device *ndev =dev_get_drvdata (priv); +struct stmmac_priv *ptr =netdev_priv (ndev); + +/* The controller and PHY don't work well together. +* We need to use the PS bit to check if the controller's status +* is correct and reset PHY if necessary. +*/ +if (speed ==SPEED_1000 ) +if (readl (ptr->ioaddr +MAC_CTRL_REG ) & (1 <<15 )/* PS */ ) +phy_restart_aneg (ndev->phydev); +} + +static int loongson_gnet_data (struct pci_dev *pdev, +struct plat_stmmacenet_data *plat) +{ +loongson_default_data (pdev, plat); + + plat->multicast_filter_bins =256 ; + + plat->mdio_bus_data->phy_mask =0xfffffffb ; + + plat->phy_addr =2 ; + plat->phy_interface =PHY_INTERFACE_MODE_INTERNAL ; + + plat->bsp_priv = &pdev->dev; + plat->fix_mac_speed = loongson_gnet_fix_speed; + + plat->dma_cfg->pbl =32 ; + plat->dma_cfg->pblx8 = true; + + plat->clk_ref_rate =125000000 ; + plat->clk_ptp_rate =125000000 ; + +return 0 ; +} + +static int loongson_gnet_config (struct pci_dev *pdev, +struct plat_stmmacenet_data *plat, +struct stmmac_resources *res, +struct device_node *np) +{ +int ret; +u32 version =readl (res->addr +GMAC_VERSION ); + +switch (version &0xff ) { +case DWLGMAC_CORE_1_00 : + ret =loongson_dwmac_config_multi_msi (pdev, plat, res, np,8 ); +break ; +default : + ret =loongson_dwmac_config_legacy (pdev, plat, res, np); +break ; + } + +switch (pdev->revision) { +case 0x00 : + plat->flags |= +FIELD_PREP (STMMAC_FLAG_DISABLE_HALF_DUPLEX ,1 ) | +FIELD_PREP (STMMAC_FLAG_DISABLE_FORCE_1000 ,1 ); +break ; +case 0x01 : + plat->flags |= +FIELD_PREP (STMMAC_FLAG_DISABLE_HALF_DUPLEX ,1 ); +break ; +default : +break ; + } + +return ret; +} + +static struct stmmac_pci_info loongson_gnet_pci_info = { + .setup = loongson_gnet_data, + .config = loongson_gnet_config, +}; +static int loongson_dwmac_probe (struct pci_dev *pdev,const struct pci_device_id *id) {
@@ -318,9 +395,11 @@ static SIMPLE_DEV_PM_OPS(loongson_dwmac_pm_ops, loongson_dwmac_suspend, loongson_dwmac_resume);#define PCI_DEVICE_ID_LOONGSON_GMAC 0x7a03 +#define PCI_DEVICE_ID_LOONGSON_GNET 0x7a13static const struct pci_device_id loongson_dwmac_id_table[] = { {PCI_DEVICE_DATA (LOONGSON ,GMAC , &loongson_gmac_pci_info) }, + {PCI_DEVICE_DATA (LOONGSON ,GNET , &loongson_gnet_pci_info) }, {} };MODULE_DEVICE_TABLE (pci, loongson_dwmac_id_table);
drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c +6 -0
@@ -420,6 +420,12 @@ stmmac_ethtool_set_link_ksettings(struct net_device *dev,return 0 ; } +if (FIELD_GET (STMMAC_FLAG_DISABLE_FORCE_1000 , priv->plat->flags)) { +if (cmd->base.speed ==SPEED_1000 && + cmd->base.autoneg !=AUTONEG_ENABLE ) +return -EOPNOTSUPP ; + } +return phylink_ethtool_ksettings_set (priv->phylink, cmd); }
include/linux/stmmac.h +2 -0
@@ -222,6 +222,8 @@ struct dwmac4_addrs {#define STMMAC_FLAG_EN_TX_LPI_CLOCKGATING BIT(11)#define STMMAC_FLAG_HWTSTAMP_CORRECT_LATENCY BIT(12)#define STMMAC_FLAG_HAS_LGMAC BIT(13) +#define STMMAC_FLAG_DISABLE_HALF_DUPLEX BIT(14) +#define STMMAC_FLAG_DISABLE_FORCE_1000 BIT(15)struct plat_stmmacenet_data {int bus_id;
Signature · 1 line
2.31.4
Re: [PATCH net-next v7 7/9] net: stmmac: dwmac-loongson: Add GNET support
Quoted 24 lines · Yanteng Si
Add Loongson GNET (GMAC with PHY) support. Current GNET does not support half duplex mode, and GNET on LS7A only supports ANE when speed is set to 1000M.
Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- .../ethernet/stmicro/stmmac/dwmac-loongson.c | 79 +++++++++++++++++++ .../ethernet/stmicro/stmmac/stmmac_ethtool.c | 6 ++ include/linux/stmmac.h | 2 + 3 files changed, 87 insertions(+)drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +3
-0@@ -168,6 +168,83 @@ static struct stmmac_pci_info loongson_gmac_pci_info = { .config = loongson_gmac_config, }; +static void loongson_gnet_fix_speed (void *priv,unsigned int speed,unsigned int mode) +{ +struct net_device *ndev =dev_get_drvdata (priv);
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 183
Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +9
-0+struct stmmac_priv *ptr =netdev_priv (ndev); + +/* The controller and PHY don't work well together. +* We need to use the PS bit to check if the controller's status +* is correct and reset PHY if necessary. +*/ +if (speed ==SPEED_1000 ) +if (readl (ptr->ioaddr +MAC_CTRL_REG ) & (1 <<15 )/* PS */ ) +phy_restart_aneg (ndev->phydev);
{} around the outer if please.
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 192
Quoted 11 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +10
-0+} + +static int loongson_gnet_data (struct pci_dev *pdev, +struct plat_stmmacenet_data *plat) +{ +loongson_default_data (pdev, plat); + + plat->multicast_filter_bins =256 ; + + plat->mdio_bus_data->phy_mask =0xfffffffb ;
~BIT(2)?
Quoted 21 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +21
-0+ + plat->phy_addr =2 ; + plat->phy_interface =PHY_INTERFACE_MODE_INTERNAL ; + + plat->bsp_priv = &pdev->dev; + plat->fix_mac_speed = loongson_gnet_fix_speed; + + plat->dma_cfg->pbl =32 ; + plat->dma_cfg->pblx8 = true; + + plat->clk_ref_rate =125000000 ; + plat->clk_ptp_rate =125000000 ; + +return 0 ; +} + +static int loongson_gnet_config (struct pci_dev *pdev, +struct plat_stmmacenet_data *plat, +struct stmmac_resources *res, +struct device_node *np) +{
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 222
Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +9
-0+int ret; +u32 version =readl (res->addr +GMAC_VERSION ); + +switch (version &0xff ) { +case DWLGMAC_CORE_1_00 : + ret =loongson_dwmac_config_multi_msi (pdev, plat, res, np,8 ); +break ; +default : + ret =loongson_dwmac_config_legacy (pdev, plat, res, np);
Hm, do you have two versions of Loongson GNET? What does the second one contain in the GMAC_VERSION register then? Can't you distinguish them by the PCI IDs (device, subsystem, revision)?
-Serge(y)
Quoted 73 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +25
-0+break ; + } + +switch (pdev->revision) { +case 0x00 : + plat->flags |= +FIELD_PREP (STMMAC_FLAG_DISABLE_HALF_DUPLEX ,1 ) | +FIELD_PREP (STMMAC_FLAG_DISABLE_FORCE_1000 ,1 ); +break ; +case 0x01 : + plat->flags |= +FIELD_PREP (STMMAC_FLAG_DISABLE_HALF_DUPLEX ,1 ); +break ; +default : +break ; + } + +return ret; +} + +static struct stmmac_pci_info loongson_gnet_pci_info = { + .setup = loongson_gnet_data, + .config = loongson_gnet_config, +}; +static int loongson_dwmac_probe(struct
pci_dev*pdev,drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +2
-0const struct pci_device_id *id) {@@ -318,9 +395,11 @@ static SIMPLE_DEV_PM_OPS(loongson_dwmac_pm_ops, loongson_dwmac_suspend, loongson_dwmac_resume);#define PCI_DEVICE_ID_LOONGSON_GMAC 0x7a03 +#define PCI_DEVICE_ID_LOONGSON_GNET 0x7a13static const struct pci_device_id loongson_dwmac_id_table[] = { {PCI_DEVICE_DATA (LOONGSON ,GMAC , &loongson_gmac_pci_info) }, + {PCI_DEVICE_DATA (LOONGSON ,GNET , &loongson_gnet_pci_info) }, {} };MODULE_DEVICE_TABLE (pci, loongson_dwmac_id_table);drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c +6
-0@@ -420,6 +420,12 @@ stmmac_ethtool_set_link_ksettings(struct net_device *dev,return 0 ; } +if (FIELD_GET (STMMAC_FLAG_DISABLE_FORCE_1000 , priv->plat->flags)) { +if (cmd->base.speed ==SPEED_1000 && + cmd->base.autoneg !=AUTONEG_ENABLE ) +return -EOPNOTSUPP ; + } +return phylink_ethtool_ksettings_set (priv->phylink, cmd); }include/linux/stmmac.h +2
-0@@ -222,6 +222,8 @@ struct dwmac4_addrs {#define STMMAC_FLAG_EN_TX_LPI_CLOCKGATING BIT(11)#define STMMAC_FLAG_HWTSTAMP_CORRECT_LATENCY BIT(12)#define STMMAC_FLAG_HAS_LGMAC BIT(13) +#define STMMAC_FLAG_DISABLE_HALF_DUPLEX BIT(14) +#define STMMAC_FLAG_DISABLE_FORCE_1000 BIT(15)struct plat_stmmacenet_data {int bus_id;Signature · 1 line
2.31.4
Re: [PATCH net-next v7 7/9] net: stmmac: dwmac-loongson: Add GNET support
Quoted 22 lines · Serge Semin
Quoted 21 lines · Yanteng Si
Add Loongson GNET (GMAC with PHY) support. Current GNET does not support half duplex mode, and GNET on LS7A only supports ANE when speed is set to 1000M.
Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- .../ethernet/stmicro/stmmac/dwmac-loongson.c | 79 +++++++++++++++++++ .../ethernet/stmicro/stmmac/stmmac_ethtool.c | 6 ++ include/linux/stmmac.h | 2 + 3 files changed, 87 insertions(+)drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +0
-0@@ -168,6 +168,83 @@ static struct stmmac_pci_info loongson_gmac_pci_info = { .config = loongson_gmac_config, };
Quoted 13 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 182
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +12
-0+static void loongson_gnet_fix_speed (void *priv,unsigned int speed,unsigned int mode) +{ +struct net_device *ndev =dev_get_drvdata (priv); +struct stmmac_priv *ptr =netdev_priv (ndev); + +/* The controller and PHY don't work well together. +* We need to use the PS bit to check if the controller's status +* is correct and reset PHY if necessary. +*/ +if (speed ==SPEED_1000 ) +if (readl (ptr->ioaddr +MAC_CTRL_REG ) & (1 <<15 )/* PS */ ) +phy_restart_aneg (ndev->phydev);{} around the outer if please.
OK.
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 192
Quoted 11 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +10
-0+} + +static int loongson_gnet_data (struct pci_dev *pdev, +struct plat_stmmacenet_data *plat) +{ +loongson_default_data (pdev, plat); + + plat->multicast_filter_bins =256 ; + + plat->mdio_bus_data->phy_mask =0xfffffffb ;~BIT(2)?
I still need to confirm, please allow me to get back to you later.
Quoted 24 lines
Quoted 24 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +23
-0+ + plat->phy_addr =2 ; + plat->phy_interface =PHY_INTERFACE_MODE_INTERNAL ; + + plat->bsp_priv = &pdev->dev; + plat->fix_mac_speed = loongson_gnet_fix_speed; + + plat->dma_cfg->pbl =32 ; + plat->dma_cfg->pblx8 = true; + + plat->clk_ref_rate =125000000 ; + plat->clk_ptp_rate =125000000 ; + +return 0 ; +} + +static int loongson_gnet_config (struct pci_dev *pdev, +struct plat_stmmacenet_data *plat, +struct stmmac_resources *res, +struct device_node *np) +{ +int ret; +u32 version =readl (res->addr +GMAC_VERSION );
Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 222
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +7
-0+ +switch (version &0xff ) { +case DWLGMAC_CORE_1_00 : + ret =loongson_dwmac_config_multi_msi (pdev, plat, res, np,8 ); +break ; +default : + ret =loongson_dwmac_config_legacy (pdev, plat, res, np);Hm, do you have two versions of Loongson GNET? What does the second
Yes.
Quoted 2 lines
one contain in the
GMAC_VERSIONregister then? Can't you distinguish them by the PCI IDs (device, subsystem, revision)?
I'm afraid that's not possible.
Because they have the same pci id and revision.
Thanks,
Yanteng
Quoted 76 lines
-Serge(y)
Quoted 73 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +27
-0+break ; + } + +switch (pdev->revision) { +case 0x00 : + plat->flags |= +FIELD_PREP (STMMAC_FLAG_DISABLE_HALF_DUPLEX ,1 ) | +FIELD_PREP (STMMAC_FLAG_DISABLE_FORCE_1000 ,1 ); +break ; +case 0x01 : + plat->flags |= +FIELD_PREP (STMMAC_FLAG_DISABLE_HALF_DUPLEX ,1 ); +break ; +default : +break ; + } + +return ret; +} + +static struct stmmac_pci_info loongson_gnet_pci_info = { + .setup = loongson_gnet_data, + .config = loongson_gnet_config, +}; +static int loongson_dwmac_probe (struct pci_dev *pdev,const struct pci_device_id *id) {@@ -318,9 +395,11 @@ static SIMPLE_DEV_PM_OPS(loongson_dwmac_pm_ops, loongson_dwmac_suspend, loongson_dwmac_resume);#define PCI_DEVICE_ID_LOONGSON_GMAC 0x7a03 +#define PCI_DEVICE_ID_LOONGSON_GNET 0x7a13static const struct pci_device_id loongson_dwmac_id_table[] = { {PCI_DEVICE_DATA (LOONGSON ,GMAC , &loongson_gmac_pci_info) }, + {PCI_DEVICE_DATA (LOONGSON ,GNET , &loongson_gnet_pci_info) }, {} };MODULE_DEVICE_TABLE (pci, loongson_dwmac_id_table);drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c +6
-0@@ -420,6 +420,12 @@ stmmac_ethtool_set_link_ksettings(struct net_device *dev,return 0 ; } +if (FIELD_GET (STMMAC_FLAG_DISABLE_FORCE_1000 , priv->plat->flags)) { +if (cmd->base.speed ==SPEED_1000 && + cmd->base.autoneg !=AUTONEG_ENABLE ) +return -EOPNOTSUPP ; + } +return phylink_ethtool_ksettings_set (priv->phylink, cmd); }include/linux/stmmac.h +2
-0@@ -222,6 +222,8 @@ struct dwmac4_addrs {#define STMMAC_FLAG_EN_TX_LPI_CLOCKGATING BIT(11)#define STMMAC_FLAG_HWTSTAMP_CORRECT_LATENCY BIT(12)#define STMMAC_FLAG_HAS_LGMAC BIT(13) +#define STMMAC_FLAG_DISABLE_HALF_DUPLEX BIT(14) +#define STMMAC_FLAG_DISABLE_FORCE_1000 BIT(15)struct plat_stmmacenet_data {int bus_id;Signature · 1 line
2.31.4
Re: [PATCH net-next v7 7/9] net: stmmac: dwmac-loongson: Add GNET support
Quoted 83 lines · Yanteng Si
Quoted 26 lines · Serge Semin
Quoted 25 lines · Yanteng Si
Add Loongson GNET (GMAC with PHY) support. Current GNET does not support half duplex mode, and GNET on LS7A only supports ANE when speed is set to 1000M.
Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- .../ethernet/stmicro/stmmac/dwmac-loongson.c | 79 +++++++++++++++++++ .../ethernet/stmicro/stmmac/stmmac_ethtool.c | 6 ++ include/linux/stmmac.h | 2 + 3 files changed, 87 insertions(+)drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +5
-0@@ -168,6 +168,83 @@ static struct stmmac_pci_info loongson_gmac_pci_info = { .config = loongson_gmac_config, }; +static void loongson_gnet_fix_speed (void *priv,unsigned int speed,unsigned int mode) +{ +struct net_device *ndev =dev_get_drvdata (priv); +struct stmmac_priv *ptr =netdev_priv (ndev); +Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 182
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +7
-0+/* The controller and PHY don't work well together. +* We need to use the PS bit to check if the controller's status +* is correct and reset PHY if necessary. +*/ +if (speed ==SPEED_1000 ) +if (readl (ptr->ioaddr +MAC_CTRL_REG ) & (1 <<15 )/* PS */ ) +phy_restart_aneg (ndev->phydev);{} around the outer if please.
OK.
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 192
Quoted 11 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +10
-0+} + +static int loongson_gnet_data (struct pci_dev *pdev, +struct plat_stmmacenet_data *plat) +{ +loongson_default_data (pdev, plat); + + plat->multicast_filter_bins =256 ; + + plat->mdio_bus_data->phy_mask =0xfffffffb ;~BIT(2)?
I still need to confirm, please allow me to get back to you later.
Quoted 25 lines
Quoted 25 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +24
-0+ + plat->phy_addr =2 ; + plat->phy_interface =PHY_INTERFACE_MODE_INTERNAL ; + + plat->bsp_priv = &pdev->dev; + plat->fix_mac_speed = loongson_gnet_fix_speed; + + plat->dma_cfg->pbl =32 ; + plat->dma_cfg->pblx8 = true; + + plat->clk_ref_rate =125000000 ; + plat->clk_ptp_rate =125000000 ; + +return 0 ; +} + +static int loongson_gnet_config (struct pci_dev *pdev, +struct plat_stmmacenet_data *plat, +struct stmmac_resources *res, +struct device_node *np) +{ +int ret; +u32 version =readl (res->addr +GMAC_VERSION ); +Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 222
Quoted 6 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +6
-0+switch (version &0xff ) { +case DWLGMAC_CORE_1_00 : + ret =loongson_dwmac_config_multi_msi (pdev, plat, res, np,8 ); +break ; +default : + ret =loongson_dwmac_config_legacy (pdev, plat, res, np);Hm, do you have two versions of Loongson GNET? What does the second
Quoted 7 lines
Yes.
Quoted 2 lines
one contain in the
GMAC_VERSIONregister then? Can't you distinguish them by the PCI IDs (device, subsystem, revision)?I'm afraid that's not possible.
Because they have the same pci id and revision.
Please provide more details about what platform/devices support you are adding and what PCI IDs and DW GMAC IP-core version they have.
Quoted 72 lines
Thanks,
Yanteng
Quoted 66 lines
-Serge(y)
Quoted 63 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +27
-0+break ; + } + +switch (pdev->revision) { +case 0x00 : + plat->flags |= +FIELD_PREP (STMMAC_FLAG_DISABLE_HALF_DUPLEX ,1 ) | +FIELD_PREP (STMMAC_FLAG_DISABLE_FORCE_1000 ,1 ); +break ; +case 0x01 : + plat->flags |= +FIELD_PREP (STMMAC_FLAG_DISABLE_HALF_DUPLEX ,1 ); +break ; +default : +break ; + } + +return ret; +} + +static struct stmmac_pci_info loongson_gnet_pci_info = { + .setup = loongson_gnet_data, + .config = loongson_gnet_config, +}; +static int loongson_dwmac_probe (struct pci_dev *pdev,const struct pci_device_id *id) {@@ -318,9 +395,11 @@ static SIMPLE_DEV_PM_OPS(loongson_dwmac_pm_ops, loongson_dwmac_suspend, loongson_dwmac_resume);#define PCI_DEVICE_ID_LOONGSON_GMAC 0x7a03 +#define PCI_DEVICE_ID_LOONGSON_GNET 0x7a13static const struct pci_device_id loongson_dwmac_id_table[] = { {PCI_DEVICE_DATA (LOONGSON ,GMAC , &loongson_gmac_pci_info) }, + {PCI_DEVICE_DATA (LOONGSON ,GNET , &loongson_gnet_pci_info) }, {} };MODULE_DEVICE_TABLE (pci, loongson_dwmac_id_table);drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c +6
-0@@ -420,6 +420,12 @@ stmmac_ethtool_set_link_ksettings(struct net_device *dev,return 0 ; } +if (FIELD_GET (STMMAC_FLAG_DISABLE_FORCE_1000 , priv->plat->flags)) { +if (cmd->base.speed ==SPEED_1000 && + cmd->base.autoneg !=AUTONEG_ENABLE ) +return -EOPNOTSUPP ; + } +return phylink_ethtool_ksettings_set (priv->phylink, cmd); }include/linux/stmmac.h +1
-0@@ -222,6 +222,8 @@ struct dwmac4_addrs {#define STMMAC_FLAG_EN_TX_LPI_CLOCKGATING BIT(11)#define STMMAC_FLAG_HWTSTAMP_CORRECT_LATENCY BIT(12)#define STMMAC_FLAG_HAS_LGMAC BIT(13) +#define STMMAC_FLAG_DISABLE_HALF_DUPLEX BIT(14)
Just noticed. I do not see this flag affecting any part of the code. Drop it if no actual action is implied by it.
-Serge(y)
Quoted 7 lines
Quoted 6 lines
Quoted 6 lines
include/linux/stmmac.h +1
-0+#define STMMAC_FLAG_DISABLE_FORCE_1000 BIT(15)struct plat_stmmacenet_data {int bus_id;Signature · 1 line
2.31.4
Re: [PATCH net-next v7 7/9] net: stmmac: dwmac-loongson: Add GNET support
Quoted 80 lines · Serge Semin
Quoted 79 lines · Yanteng Si
Quoted 26 lines · Serge Semin
Quoted 25 lines · Yanteng Si
Add Loongson GNET (GMAC with PHY) support. Current GNET does not support half duplex mode, and GNET on LS7A only supports ANE when speed is set to 1000M.
Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- .../ethernet/stmicro/stmmac/dwmac-loongson.c | 79 +++++++++++++++++++ .../ethernet/stmicro/stmmac/stmmac_ethtool.c | 6 ++ include/linux/stmmac.h | 2 + 3 files changed, 87 insertions(+)drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +5
-0@@ -168,6 +168,83 @@ static struct stmmac_pci_info loongson_gmac_pci_info = { .config = loongson_gmac_config, }; +static void loongson_gnet_fix_speed (void *priv,unsigned int speed,unsigned int mode) +{ +struct net_device *ndev =dev_get_drvdata (priv); +struct stmmac_priv *ptr =netdev_priv (ndev); +Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 182
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +7
-0+/* The controller and PHY don't work well together. +* We need to use the PS bit to check if the controller's status +* is correct and reset PHY if necessary. +*/ +if (speed ==SPEED_1000 ) +if (readl (ptr->ioaddr +MAC_CTRL_REG ) & (1 <<15 )/* PS */ ) +phy_restart_aneg (ndev->phydev);{} around the outer if please.
OK.
Quoted 11 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 192
Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +10
-0+} + +static int loongson_gnet_data (struct pci_dev *pdev, +struct plat_stmmacenet_data *plat) +{ +loongson_default_data (pdev, plat); + + plat->multicast_filter_bins =256 ; + + plat->mdio_bus_data->phy_mask =0xfffffffb ;~BIT(2)?
I still need to confirm, please allow me to get back to you later.
Quoted 31 lines
Quoted 20 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +20
-0+ + plat->phy_addr =2 ; + plat->phy_interface =PHY_INTERFACE_MODE_INTERNAL ; + + plat->bsp_priv = &pdev->dev; + plat->fix_mac_speed = loongson_gnet_fix_speed; + + plat->dma_cfg->pbl =32 ; + plat->dma_cfg->pblx8 = true; + + plat->clk_ref_rate =125000000 ; + plat->clk_ptp_rate =125000000 ; + +return 0 ; +} + +static int loongson_gnet_config (struct pci_dev *pdev, +struct plat_stmmacenet_data *plat, +struct stmmac_resources *res, +struct device_node *np)drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 222
Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +10
-0+{ +int ret; +u32 version =readl (res->addr +GMAC_VERSION ); + +switch (version &0xff ) { +case DWLGMAC_CORE_1_00 : + ret =loongson_dwmac_config_multi_msi (pdev, plat, res, np,8 ); +break ; +default : + ret =loongson_dwmac_config_legacy (pdev, plat, res, np);Hm, do you have two versions of Loongson GNET? What does the second
Quoted 8 lines
Quoted 6 lines
Yes.
Quoted 2 lines
one contain in the
GMAC_VERSIONregister then? Can't you distinguish them by the PCI IDs (device, subsystem, revision)?I'm afraid that's not possible.
Because they have the same pci id and revision.
Please provide more details about what platform/devices support you are adding and what PCI IDs and DW GMAC IP-core version they have.
Okay, I will do my best to make them appear in the next version of the commit message.
Quoted 64 lines
Quoted 64 lines
Thanks,
Yanteng
Quoted 58 lines
-Serge(y)
Quoted 56 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +27
-0+break ; + } + +switch (pdev->revision) { +case 0x00 : + plat->flags |= +FIELD_PREP (STMMAC_FLAG_DISABLE_HALF_DUPLEX ,1 ) | +FIELD_PREP (STMMAC_FLAG_DISABLE_FORCE_1000 ,1 ); +break ; +case 0x01 : + plat->flags |= +FIELD_PREP (STMMAC_FLAG_DISABLE_HALF_DUPLEX ,1 ); +break ; +default : +break ; + } + +return ret; +} + +static struct stmmac_pci_info loongson_gnet_pci_info = { + .setup = loongson_gnet_data, + .config = loongson_gnet_config, +}; +static int loongson_dwmac_probe (struct pci_dev *pdev,const struct pci_device_id *id) {@@ -318,9 +395,11 @@ static SIMPLE_DEV_PM_OPS(loongson_dwmac_pm_ops, loongson_dwmac_suspend, loongson_dwmac_resume);#define PCI_DEVICE_ID_LOONGSON_GMAC 0x7a03 +#define PCI_DEVICE_ID_LOONGSON_GNET 0x7a13static const struct pci_device_id loongson_dwmac_id_table[] = { {PCI_DEVICE_DATA (LOONGSON ,GMAC , &loongson_gmac_pci_info) }, + {PCI_DEVICE_DATA (LOONGSON ,GNET , &loongson_gnet_pci_info) }, {} };MODULE_DEVICE_TABLE (pci, loongson_dwmac_id_table);drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c +6
-0@@ -420,6 +420,12 @@ stmmac_ethtool_set_link_ksettings(struct net_device *dev,return 0 ; } +if (FIELD_GET (STMMAC_FLAG_DISABLE_FORCE_1000 , priv->plat->flags)) { +if (cmd->base.speed ==SPEED_1000 && + cmd->base.autoneg !=AUTONEG_ENABLE ) +return -EOPNOTSUPP ; + } +return phylink_ethtool_ksettings_set (priv->phylink, cmd); }include/linux/stmmac.h +0
-1--- a/include/linux/stmmac.h
Quoted 8 lines
Quoted 6 lines
Quoted 6 lines
include/linux/stmmac.h struct dwmac4_addrs { · line 225
Quoted 6 lines
+++
b/include/linux/stmmac.hinclude/linux/stmmac.h +1
-0@@ -222,6 +222,8 @@ struct dwmac4_addrs {#define STMMAC_FLAG_EN_TX_LPI_CLOCKGATING BIT(11)#define STMMAC_FLAG_HWTSTAMP_CORRECT_LATENCY BIT(12)#define STMMAC_FLAG_HAS_LGMAC BIT(13) +#define STMMAC_FLAG_DISABLE_HALF_DUPLEX BIT(14)Just noticed. I do not see this flag affecting any part of the code. Drop it if no actual action is implied by it.
Sorry, I lost it, it will be added in the next version, otherwise there will be an
error on the 7a13 0x37 device.
@@ -1201,7 +1201,8 @@ static int stmmac_init_phy(struct net_device *dev) static void stmmac_set_half_duplex(struct stmmac_priv *priv) {
/* Half-Duplex can only work with single tx queue */ - if (priv->plat->tx_queues_to_use > 1)
+ if (priv->plat->tx_queues_to_use > 1 ||
+ (STMMAC_FLAG_DISABLE_HALF_DUPLEX & priv->plat->flags)) priv->phylink_config.mac_capabilities &= ~(MAC_10HD | MAC_100HD | MAC_1000HD);
else
Thanks,
Yanteng
Quoted 9 lines
-Serge(y)
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
include/linux/stmmac.h +1
-0+#define STMMAC_FLAG_DISABLE_FORCE_1000 BIT(15)struct plat_stmmacenet_data {int bus_id;Signature · 1 line
2.31.4
Re: [PATCH net-next v7 7/9] net: stmmac: dwmac-loongson: Add GNET support
In reply to Serge SeminQuoted 80 lines · Serge Semin
Quoted 79 lines · Yanteng Si
Quoted 26 lines · Serge Semin
Quoted 25 lines · Yanteng Si
Add Loongson GNET (GMAC with PHY) support. Current GNET does not support half duplex mode, and GNET on LS7A only supports ANE when speed is set to 1000M.
Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- .../ethernet/stmicro/stmmac/dwmac-loongson.c | 79 +++++++++++++++++++ .../ethernet/stmicro/stmmac/stmmac_ethtool.c | 6 ++ include/linux/stmmac.h | 2 + 3 files changed, 87 insertions(+)drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +5
-0@@ -168,6 +168,83 @@ static struct stmmac_pci_info loongson_gmac_pci_info = { .config = loongson_gmac_config, }; +static void loongson_gnet_fix_speed (void *priv,unsigned int speed,unsigned int mode) +{ +struct net_device *ndev =dev_get_drvdata (priv); +struct stmmac_priv *ptr =netdev_priv (ndev); +Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 182
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +7
-0+/* The controller and PHY don't work well together. +* We need to use the PS bit to check if the controller's status +* is correct and reset PHY if necessary. +*/ +if (speed ==SPEED_1000 ) +if (readl (ptr->ioaddr +MAC_CTRL_REG ) & (1 <<15 )/* PS */ ) +phy_restart_aneg (ndev->phydev);{} around the outer if please.
OK.
Quoted 11 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 192
Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +10
-0+} + +static int loongson_gnet_data (struct pci_dev *pdev, +struct plat_stmmacenet_data *plat) +{ +loongson_default_data (pdev, plat); + + plat->multicast_filter_bins =256 ; + + plat->mdio_bus_data->phy_mask =0xfffffffb ;~BIT(2)?
I still need to confirm, please allow me to get back to you later.
Quoted 31 lines
Quoted 20 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +20
-0+ + plat->phy_addr =2 ; + plat->phy_interface =PHY_INTERFACE_MODE_INTERNAL ; + + plat->bsp_priv = &pdev->dev; + plat->fix_mac_speed = loongson_gnet_fix_speed; + + plat->dma_cfg->pbl =32 ; + plat->dma_cfg->pblx8 = true; + + plat->clk_ref_rate =125000000 ; + plat->clk_ptp_rate =125000000 ; + +return 0 ; +} + +static int loongson_gnet_config (struct pci_dev *pdev, +struct plat_stmmacenet_data *plat, +struct stmmac_resources *res, +struct device_node *np)drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 222
Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +10
-0+{ +int ret; +u32 version =readl (res->addr +GMAC_VERSION ); + +switch (version &0xff ) { +case DWLGMAC_CORE_1_00 : + ret =loongson_dwmac_config_multi_msi (pdev, plat, res, np,8 ); +break ; +default : + ret =loongson_dwmac_config_legacy (pdev, plat, res, np);Hm, do you have two versions of Loongson GNET? What does the second
Quoted 8 lines
Quoted 6 lines
Yes.
Quoted 2 lines
one contain in the
GMAC_VERSIONregister then? Can't you distinguish them by the PCI IDs (device, subsystem, revision)?I'm afraid that's not possible.
Because they have the same pci id and revision.
Please provide more details about what platform/devices support you are adding and what PCI IDs and DW GMAC IP-core version they have.
DWLGMAC_CORE_1_00 has been removed and I am already making patches.
Thanks,
Yanteng
Quoted 81 lines
Quoted 62 lines
Thanks,
Yanteng
Quoted 56 lines
-Serge(y)
Quoted 54 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +27
-0+break ; + } + +switch (pdev->revision) { +case 0x00 : + plat->flags |= +FIELD_PREP (STMMAC_FLAG_DISABLE_HALF_DUPLEX ,1 ) | +FIELD_PREP (STMMAC_FLAG_DISABLE_FORCE_1000 ,1 ); +break ; +case 0x01 : + plat->flags |= +FIELD_PREP (STMMAC_FLAG_DISABLE_HALF_DUPLEX ,1 ); +break ; +default : +break ; + } + +return ret; +} + +static struct stmmac_pci_info loongson_gnet_pci_info = { + .setup = loongson_gnet_data, + .config = loongson_gnet_config, +}; +static int loongson_dwmac_probe (struct pci_dev *pdev,const struct pci_device_id *id) {@@ -318,9 +395,11 @@ static SIMPLE_DEV_PM_OPS(loongson_dwmac_pm_ops, loongson_dwmac_suspend, loongson_dwmac_resume);#define PCI_DEVICE_ID_LOONGSON_GMAC 0x7a03 +#define PCI_DEVICE_ID_LOONGSON_GNET 0x7a13static const struct pci_device_id loongson_dwmac_id_table[] = { {PCI_DEVICE_DATA (LOONGSON ,GMAC , &loongson_gmac_pci_info) }, + {PCI_DEVICE_DATA (LOONGSON ,GNET , &loongson_gnet_pci_info) }, {} };MODULE_DEVICE_TABLE (pci, loongson_dwmac_id_table);drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c +6
-0@@ -420,6 +420,12 @@ stmmac_ethtool_set_link_ksettings(struct net_device *dev,return 0 ; } +if (FIELD_GET (STMMAC_FLAG_DISABLE_FORCE_1000 , priv->plat->flags)) { +if (cmd->base.speed ==SPEED_1000 && + cmd->base.autoneg !=AUTONEG_ENABLE ) +return -EOPNOTSUPP ; + } +return phylink_ethtool_ksettings_set (priv->phylink, cmd); }include/linux/stmmac.h +0
-0Quoted 8 lines
Quoted 8 lines
include/linux/stmmac.h struct dwmac4_addrs { · line 225
Quoted 8 lines
index
f07f79d50b06..067030cdb60f100644include/linux/stmmac.h +1
-0@@ -222,6 +222,8 @@ struct dwmac4_addrs {#define STMMAC_FLAG_EN_TX_LPI_CLOCKGATING BIT(11)#define STMMAC_FLAG_HWTSTAMP_CORRECT_LATENCY BIT(12)#define STMMAC_FLAG_HAS_LGMAC BIT(13) +#define STMMAC_FLAG_DISABLE_HALF_DUPLEX BIT(14)Just noticed. I do not see this flag affecting any part of the code. Drop it if no actual action is implied by it.
-Serge(y)
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
include/linux/stmmac.h +1
-0+#define STMMAC_FLAG_DISABLE_FORCE_1000 BIT(15)struct plat_stmmacenet_data {int bus_id;Signature · 1 line
2.31.4
Re: [PATCH net-next v7 7/9] net: stmmac: dwmac-loongson: Add GNET support
In reply to Yanteng SiQuoted 51 lines · Yanteng Si
Quoted 28 lines · Serge Semin
Quoted 27 lines · Yanteng Si
Add Loongson GNET (GMAC with PHY) support. Current GNET does not support half duplex mode, and GNET on LS7A only supports ANE when speed is set to 1000M.
Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>---
.../ethernet/stmicro/stmmac/dwmac-loongson.c | 79
+++++++++++++++++++
.../ethernet/stmicro/stmmac/stmmac_ethtool.c | 6 ++ include/linux/stmmac.h | 2 +3 files changed, 87 insertions(+)drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +4
-0@@ -168,6 +168,83 @@ static struct stmmac_pci_info loongson_gmac_pci_info = { .config = loongson_gmac_config, }; +static void loongson_gnet_fix_speed(void *priv, unsigned int speed, unsigned int mode) +{ + struct net_device *ndev = dev_get_drvdata(priv); + struct stmmac_priv *ptr = netdev_priv(ndev); +Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 182
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +7
-0+ /* The controller and PHY don't work well together. + * We need to use the PS bit to check if the controller's status + * is correct and reset PHY if necessary. + */ + if (speed == SPEED_1000) + if (readl(ptr->ioaddr + MAC_CTRL_REG) & (1 << 15) /* PS */) + phy_restart_aneg(ndev->phydev);{} around the outer if please.
OK.
Quoted 12 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 192
Quoted 11 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +10
-0+} + +static int loongson_gnet_data (struct pci_dev *pdev, + struct plat_stmmacenet_data *plat) +{ + loongson_default_data(pdev, plat); + + plat->multicast_filter_bins = 256; + + plat->mdio_bus_data->phy_mask = 0xfffffffb;~BIT(2)?
Quoted 1 line
I still need to confirm, please allow me to get back to you later.
Yes, that's fine.
Thanks,
Yanteng
Quoted 118 lines
Quoted 24 lines
Quoted 24 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +23
-0+ + plat->phy_addr = 2; + plat->phy_interface = PHY_INTERFACE_MODE_INTERNAL; + + plat->bsp_priv = &pdev->dev; + plat->fix_mac_speed = loongson_gnet_fix_speed; + + plat->dma_cfg->pbl = 32; + plat->dma_cfg->pblx8 = true; + + plat->clk_ref_rate = 125000000; + plat->clk_ptp_rate = 125000000; + + return 0; +} + +static int loongson_gnet_config (struct pci_dev *pdev, + struct plat_stmmacenet_data *plat, + struct stmmac_resources *res, + struct device_node *np) +{ + int ret; + u32 version = readl(res->addr + GMAC_VERSION);Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 222
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +7
-0+ + switch (version & 0xff) { + case DWLGMAC_CORE_1_00: + ret = loongson_dwmac_config_multi_msi(pdev, plat, res, np, 8); + break; + default: + ret = loongson_dwmac_config_legacy(pdev, plat, res, np);Hm, do you have two versions of Loongson GNET? What does the second
Yes.
Quoted 2 lines
one contain in the
GMAC_VERSIONregister then? Can't you distinguish them by the PCI IDs (device, subsystem, revision)?I'm afraid that's not possible.
Because they have the same pci id and revision.
Thanks,
Yanteng
Quoted 73 lines
-Serge(y)
Quoted 70 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +25
-0+ break; + } + + switch (pdev->revision) { + case 0x00: + plat->flags |= + FIELD_PREP(STMMAC_FLAG_DISABLE_HALF_DUPLEX, 1) | + FIELD_PREP(STMMAC_FLAG_DISABLE_FORCE_1000, 1); + break; + case 0x01: + plat->flags |= + FIELD_PREP(STMMAC_FLAG_DISABLE_HALF_DUPLEX, 1); + break; + default: + break; + } + + return ret; +} + +static struct stmmac_pci_info loongson_gnet_pci_info = { + .setup = loongson_gnet_data, + .config = loongson_gnet_config, +}; + static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id *id){
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +2
-0@@ -318,9 +395,11 @@ static SIMPLE_DEV_PM_OPS(loongson_dwmac_pm_ops, loongson_dwmac_suspend, loongson_dwmac_resume); #define PCI_DEVICE_ID_LOONGSON_GMAC 0x7a03 +#define PCI_DEVICE_ID_LOONGSON_GNET 0x7a13 static const struct pci_device_id loongson_dwmac_id_table[] = { { PCI_DEVICE_DATA(LOONGSON, GMAC, &loongson_gmac_pci_info) }, + { PCI_DEVICE_DATA(LOONGSON, GNET, &loongson_gnet_pci_info) }, {} }; MODULE_DEVICE_TABLE(pci, loongson_dwmac_id_table);drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c +5
-0@@ -420,6 +420,12 @@ stmmac_ethtool_set_link_ksettings(structnet_device *dev, return 0; } + if (FIELD_GET(STMMAC_FLAG_DISABLE_FORCE_1000, priv->plat->flags)) { + if (cmd->base.speed == SPEED_1000 && + cmd->base.autoneg != AUTONEG_ENABLE) + return -EOPNOTSUPP; + } + return phylink_ethtool_ksettings_set(priv->phylink, cmd); }diff --git
a/include/linux/stmmac.hb/include/linux/stmmac.hindexf07f79d50b06..067030cdb60f100644include/linux/stmmac.h +2
-0@@ -222,6 +222,8 @@ struct dwmac4_addrs { #define STMMAC_FLAG_EN_TX_LPI_CLOCKGATING BIT(11) #define STMMAC_FLAG_HWTSTAMP_CORRECT_LATENCY BIT(12) #define STMMAC_FLAG_HAS_LGMAC BIT(13) +#define STMMAC_FLAG_DISABLE_HALF_DUPLEX BIT(14) +#define STMMAC_FLAG_DISABLE_FORCE_1000 BIT(15) struct plat_stmmacenet_data { int bus_id;Signature · 1 line
2.31.4
Re: [PATCH net-next v7 7/9] net: stmmac: dwmac-loongson: Add GNET support
Quoted 57 lines · Yanteng Si
Quoted 54 lines · Yanteng Si
Quoted 33 lines · Serge Semin
Quoted 32 lines · Yanteng Si
Add Loongson GNET (GMAC with PHY) support. Current GNET does not support
half duplex mode, and GNET on LS7A only supports ANE when speed is set to
1000M.Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>---
.../ethernet/stmicro/stmmac/dwmac-loongson.c | 79
+++++++++++++++++++
.../ethernet/stmicro/stmmac/stmmac_ethtool.c | 6 ++ include/linux/stmmac.h | 2 +3 files changed, 87 insertions(+)diff --git
a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.cb/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.cindex2c08d5495214..9e4953c7e4e0100644drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +0
-0@@ -168,6 +168,83 @@ static struct stmmac_pci_info loongson_gmac_pci_info = { .config = loongson_gmac_config, };+static void
loongson_gnet_fix_speed(void *priv, unsigned int speed, unsigned int mode)drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +4
-0+{ + struct net_device *ndev = dev_get_drvdata(priv); + struct stmmac_priv *ptr = netdev_priv(ndev); +Quoted 8 lines
Quoted 7 lines
+ /* The controller and PHY don't work well together.
+ * We need to use the PS bit to check if the controller's status + * is correct and reset PHY if necessary.
+ */
+ if (speed ==SPEED_1000)
+ if (readl(ptr->ioaddr + MAC_CTRL_REG)& (1 << 15) /* PS */) +phy_restart_aneg(ndev->phydev);{} around the outer if please.
OK.
Quoted 10 lines
Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +9
-0+} + +static int loongson_gnet_data (struct pci_dev *pdev, + struct plat_stmmacenet_data *plat) +{ + loongson_default_data(pdev, plat); + + plat->multicast_filter_bins = 256; +
Quoted 5 lines
Quoted 3 lines
Quoted 2 lines
Quoted 1 line
+
plat->mdio_bus_data->phy_mask=0xfffffffb;~BIT(2)?
I still need to confirm, please allow me to get back to you later.
Yes, that's fine.
Glad this part has been settled.)
-Serge(y)
Quoted 129 lines
Thanks,
Yanteng
Quoted 121 lines
Quoted 24 lines
Quoted 24 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +23
-0+ + plat->phy_addr = 2; + plat->phy_interface = PHY_INTERFACE_MODE_INTERNAL; + + plat->bsp_priv = &pdev->dev; + plat->fix_mac_speed = loongson_gnet_fix_speed; + + plat->dma_cfg->pbl = 32; + plat->dma_cfg->pblx8 = true; + + plat->clk_ref_rate = 125000000; + plat->clk_ptp_rate = 125000000; + + return 0; +} + +static int loongson_gnet_config (struct pci_dev *pdev, + struct plat_stmmacenet_data *plat, + struct stmmac_resources *res, + struct device_node *np) +{ + int ret; + u32 version = readl(res->addr + GMAC_VERSION);Quoted 8 lines
Quoted 7 lines
+
+ switch (version &0xff) {
+ caseDWLGMAC_CORE_1_00:
+ ret =loongson_dwmac_config_multi_msi(pdev, plat, res, np, 8); + break;
+ default:
+ ret =loongson_dwmac_config_legacy(pdev, plat, res, np);Hm, do you have two versions of Loongson GNET? What does the second
Yes.
Quoted 2 lines
one contain in the
GMAC_VERSIONregister then? Can't you distinguish them by the PCI IDs (device, subsystem, revision)?I'm afraid that's not possible.
Because they have the same pci id and revision.
Thanks,
Yanteng
Quoted 76 lines
-Serge(y)
Quoted 73 lines
+ break;
+ }drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +23
-0+ + switch (pdev->revision) { + case 0x00: + plat->flags |= + FIELD_PREP(STMMAC_FLAG_DISABLE_HALF_DUPLEX, 1) | + FIELD_PREP(STMMAC_FLAG_DISABLE_FORCE_1000, 1); + break; + case 0x01: + plat->flags |= + FIELD_PREP(STMMAC_FLAG_DISABLE_HALF_DUPLEX, 1); + break; + default: + break; + } + + return ret; +} + +static struct stmmac_pci_info loongson_gnet_pci_info = { + .setup = loongson_gnet_data, + .config = loongson_gnet_config, +}; +static int
loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id *id){drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +2
-0@@ -318,9 +395,11 @@ staticSIMPLE_DEV_PM_OPS (loongson_dwmac_pm_ops, loongson_dwmac_suspend, loongson_dwmac_resume); #define PCI_DEVICE_ID_LOONGSON_GMAC 0x7a03 +#define PCI_DEVICE_ID_LOONGSON_GNET 0x7a13 static const struct pci_device_id loongson_dwmac_id_table[] = { { PCI_DEVICE_DATA(LOONGSON, GMAC, &loongson_gmac_pci_info) }, + { PCI_DEVICE_DATA(LOONGSON, GNET, &loongson_gnet_pci_info) }, {} }; MODULE_DEVICE_TABLE(pci, loongson_dwmac_id_table);diff --git
a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.cb/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.cindex8105ce47c6ad..d6939eb9a0d8100644drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c +5
-0@@ -420,6 +420,12 @@ stmmac_ethtool_set_link_ksettings(structnet_device *dev, return 0; } + if (FIELD_GET(STMMAC_FLAG_DISABLE_FORCE_1000, priv->plat->flags)) { + if (cmd->base.speed == SPEED_1000 && + cmd->base.autoneg != AUTONEG_ENABLE) + return -EOPNOTSUPP; + } + return phylink_ethtool_ksettings_set(priv->phylink, cmd);}
diff --gita/include/linux/stmmac.hb/include/linux/stmmac.hindexf07f79d50b06..067030cdb60f100644include/linux/stmmac.h +2
-0@@ -222,6 +222,8 @@ struct dwmac4_addrs { #define STMMAC_FLAG_EN_TX_LPI_CLOCKGATING BIT(11) #define STMMAC_FLAG_HWTSTAMP_CORRECT_LATENCY BIT(12) #define STMMAC_FLAG_HAS_LGMAC BIT(13) +#define STMMAC_FLAG_DISABLE_HALF_DUPLEX BIT(14) +#define STMMAC_FLAG_DISABLE_FORCE_1000 BIT(15) struct plat_stmmacenet_data { int bus_id;Signature · 1 line
2.31.4
Re: [PATCH net-next v7 7/9] net: stmmac: dwmac-loongson: Add GNET support
Quoted 56 lines · Serge Semin
Quoted 55 lines · Yanteng Si
Quoted 54 lines · Yanteng Si
Quoted 33 lines · Serge Semin
Quoted 32 lines · Yanteng Si
Add Loongson GNET (GMAC with PHY) support. Current GNET does not support
half duplex mode, and GNET on LS7A only supports ANE when speed is set to
1000M.Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- .../ethernet/stmicro/stmmac/dwmac-loongson.c | 79 +++++++++++++++++++ .../ethernet/stmicro/stmmac/stmmac_ethtool.c | 6 ++ include/linux/stmmac.h | 2 + 3 files changed, 87 insertions(+)diff --git
a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.cb/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.cindex2c08d5495214..9e4953c7e4e0100644drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +4
-0@@ -168,6 +168,83 @@ static struct stmmac_pci_info loongson_gmac_pci_info = { .config = loongson_gmac_config, }; +static void loongson_gnet_fix_speed(void *priv, unsigned int speed,unsigned int mode) +{ + struct net_device *ndev = dev_get_drvdata(priv); + struct stmmac_priv *ptr = netdev_priv(ndev); +Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 182
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +7
-0+ /* The controller and PHY don't work well together. + * We need to use the PS bit to check if the controller's status + * is correct and reset PHY if necessary. + */ + if (speed == SPEED_1000) + if (readl(ptr->ioaddr + MAC_CTRL_REG) & (1 << 15) /* PS */) + phy_restart_aneg(ndev->phydev);{} around the outer if please.
OK.
Quoted 11 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 192
Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +10
-0+} + +static int loongson_gnet_data (struct pci_dev *pdev, + struct plat_stmmacenet_data *plat) +{ + loongson_default_data(pdev, plat); + + plat->multicast_filter_bins = 256; + + plat->mdio_bus_data->phy_mask = 0xfffffffb;~BIT(2)?
Quoted 2 lines
Quoted 2 lines
Quoted 1 line
I still need to confirm, please allow me to get back to you later.
Yes, that's fine.
Oops! A warning will be output:
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c: In function 'loongson_gnet_data':drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c:463:41: warning: conversion from
'long unsigned int' to 'unsigned int' changes value from '18446744073709551611' to '4294967291' [-Woverflow] 463 | plat->mdio_bus_data->phy_mask = ~BIT(2);
| ^
Unfortunately, we don't have an unsigned int macro for BIT(nr).
Thanks,
Yanteng
Quoted 127 lines
-Serge(y)
Quoted 124 lines
Thanks,
Yanteng
Quoted 118 lines
Quoted 23 lines
Quoted 23 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +23
-0+ + plat->phy_addr = 2; + plat->phy_interface = PHY_INTERFACE_MODE_INTERNAL; + + plat->bsp_priv = &pdev->dev; + plat->fix_mac_speed = loongson_gnet_fix_speed; + + plat->dma_cfg->pbl = 32; + plat->dma_cfg->pblx8 = true; + + plat->clk_ref_rate = 125000000; + plat->clk_ptp_rate = 125000000; + + return 0; +} + +static int loongson_gnet_config (struct pci_dev *pdev, + struct plat_stmmacenet_data *plat, + struct stmmac_resources *res, + struct device_node *np) +{ + int ret; + u32 version = readl(res->addr + GMAC_VERSION);Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 222
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +7
-0+ + switch (version & 0xff) { + case DWLGMAC_CORE_1_00: + ret = loongson_dwmac_config_multi_msi(pdev, plat, res, np, 8); + break; + default: + ret = loongson_dwmac_config_legacy(pdev, plat, res, np);Hm, do you have two versions of Loongson GNET? What does the second
Yes.
Quoted 2 lines
one contain in the
GMAC_VERSIONregister then? Can't you distinguish them by the PCI IDs (device, subsystem, revision)?I'm afraid that's not possible.
Because they have the same pci id and revision.
Thanks,
Yanteng
Quoted 75 lines
-Serge(y)
Quoted 73 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +27
-0+ break; + } + + switch (pdev->revision) { + case 0x00: + plat->flags |= + FIELD_PREP(STMMAC_FLAG_DISABLE_HALF_DUPLEX, 1) | + FIELD_PREP(STMMAC_FLAG_DISABLE_FORCE_1000, 1); + break; + case 0x01: + plat->flags |= + FIELD_PREP(STMMAC_FLAG_DISABLE_HALF_DUPLEX, 1); + break; + default: + break; + } + + return ret; +} + +static struct stmmac_pci_info loongson_gnet_pci_info = { + .setup = loongson_gnet_data, + .config = loongson_gnet_config, +}; + static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id *id) {@@ -318,9 +395,11 @@ staticSIMPLE_DEV_PM_OPS (loongson_dwmac_pm_ops, loongson_dwmac_suspend, loongson_dwmac_resume); #define PCI_DEVICE_ID_LOONGSON_GMAC 0x7a03 +#define PCI_DEVICE_ID_LOONGSON_GNET 0x7a13 static const struct pci_device_id loongson_dwmac_id_table[] = { { PCI_DEVICE_DATA(LOONGSON, GMAC, &loongson_gmac_pci_info) }, + { PCI_DEVICE_DATA(LOONGSON, GNET, &loongson_gnet_pci_info) }, {} }; MODULE_DEVICE_TABLE(pci, loongson_dwmac_id_table);diff --git
a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.cb/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.cindex8105ce47c6ad..d6939eb9a0d8100644drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c +5
-0@@ -420,6 +420,12 @@ stmmac_ethtool_set_link_ksettings(structnet_device *dev, return 0; } + if (FIELD_GET(STMMAC_FLAG_DISABLE_FORCE_1000, priv->plat->flags)) { + if (cmd->base.speed == SPEED_1000 && + cmd->base.autoneg != AUTONEG_ENABLE) + return -EOPNOTSUPP; + } + return phylink_ethtool_ksettings_set(priv->phylink, cmd); } diff --git a/include/linux/stmmac.h b/include/linux/stmmac.hindex
f07f79d50b06..067030cdb60f100644include/linux/stmmac.h +2
-0@@ -222,6 +222,8 @@ struct dwmac4_addrs { #define STMMAC_FLAG_EN_TX_LPI_CLOCKGATING BIT(11) #define STMMAC_FLAG_HWTSTAMP_CORRECT_LATENCY BIT(12) #define STMMAC_FLAG_HAS_LGMAC BIT(13) +#define STMMAC_FLAG_DISABLE_HALF_DUPLEX BIT(14) +#define STMMAC_FLAG_DISABLE_FORCE_1000 BIT(15) struct plat_stmmacenet_data { int bus_id;Signature · 1 line
2.31.4
Re: [PATCH net-next v7 7/9] net: stmmac: dwmac-loongson: Add GNET support
Quoted 69 lines · Yanteng Si
Quoted 56 lines · Serge Semin
Quoted 55 lines · Yanteng Si
Quoted 54 lines · Yanteng Si
Quoted 33 lines · Serge Semin
Quoted 32 lines · Yanteng Si
Add Loongson GNET (GMAC with PHY) support. Current GNET does not support
half duplex mode, and GNET on LS7A only supports ANE when speed is set to
1000M.Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- .../ethernet/stmicro/stmmac/dwmac-loongson.c | 79 +++++++++++++++++++ .../ethernet/stmicro/stmmac/stmmac_ethtool.c | 6 ++ include/linux/stmmac.h | 2 + 3 files changed, 87 insertions(+)diff --git
a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.cb/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.cindex2c08d5495214..9e4953c7e4e0100644drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +4
-0@@ -168,6 +168,83 @@ static struct stmmac_pci_info loongson_gmac_pci_info = { .config = loongson_gmac_config, }; +static void loongson_gnet_fix_speed(void *priv, unsigned int speed,unsigned int mode) +{ + struct net_device *ndev = dev_get_drvdata(priv); + struct stmmac_priv *ptr = netdev_priv(ndev); +Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 182
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +7
-0+ /* The controller and PHY don't work well together. + * We need to use the PS bit to check if the controller's status + * is correct and reset PHY if necessary. + */ + if (speed == SPEED_1000) + if (readl(ptr->ioaddr + MAC_CTRL_REG) & (1 << 15) /* PS */) + phy_restart_aneg(ndev->phydev);{} around the outer if please.
OK.
Quoted 11 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 192
Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +10
-0+} + +static int loongson_gnet_data (struct pci_dev *pdev, + struct plat_stmmacenet_data *plat) +{ + loongson_default_data(pdev, plat); + + plat->multicast_filter_bins = 256; + + plat->mdio_bus_data->phy_mask = 0xfffffffb;~BIT(2)?
Quoted 2 lines
Quoted 2 lines
Quoted 1 line
I still need to confirm, please allow me to get back to you later.
Yes, that's fine.
Oops! A warning will be output:
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c: In function 'loongson_gnet_data':drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c:463:41: warning:
conversion from
Quoted 6 lines
'long unsigned int' to 'unsigned int' changes value from '18446744073709551611' to '4294967291' [-Woverflow] 463 |
plat->mdio_bus_data->phy_mask= ~BIT(2); | ^Unfortunately, we don't have an unsigned int macro for BIT(nr).
Then the alternative ~(1 << 2) would be still more readable then the open-coded literal like 0xfffffffb. What would be even better than that:
#define LOONGSON_GNET_PHY_ADDR 0x2
...
plat->mdio_bus_data->phy_mask = ~(1 << LOONGSON_GNET_PHY_ADDR);
...
-Serge(y)
Quoted 134 lines
Thanks,
Yanteng
Quoted 127 lines
-Serge(y)
Quoted 124 lines
Thanks,
Yanteng
Quoted 118 lines
Quoted 23 lines
Quoted 23 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +23
-0+ + plat->phy_addr = 2; + plat->phy_interface = PHY_INTERFACE_MODE_INTERNAL; + + plat->bsp_priv = &pdev->dev; + plat->fix_mac_speed = loongson_gnet_fix_speed; + + plat->dma_cfg->pbl = 32; + plat->dma_cfg->pblx8 = true; + + plat->clk_ref_rate = 125000000; + plat->clk_ptp_rate = 125000000; + + return 0; +} + +static int loongson_gnet_config (struct pci_dev *pdev, + struct plat_stmmacenet_data *plat, + struct stmmac_resources *res, + struct device_node *np) +{ + int ret; + u32 version = readl(res->addr + GMAC_VERSION);Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 222
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +7
-0+ + switch (version & 0xff) { + case DWLGMAC_CORE_1_00: + ret = loongson_dwmac_config_multi_msi(pdev, plat, res, np, 8); + break; + default: + ret = loongson_dwmac_config_legacy(pdev, plat, res, np);Hm, do you have two versions of Loongson GNET? What does the second
Yes.
Quoted 2 lines
one contain in the
GMAC_VERSIONregister then? Can't you distinguish them by the PCI IDs (device, subsystem, revision)?I'm afraid that's not possible.
Because they have the same pci id and revision.
Thanks,
Yanteng
Quoted 75 lines
-Serge(y)
Quoted 73 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +27
-0+ break; + } + + switch (pdev->revision) { + case 0x00: + plat->flags |= + FIELD_PREP(STMMAC_FLAG_DISABLE_HALF_DUPLEX, 1) | + FIELD_PREP(STMMAC_FLAG_DISABLE_FORCE_1000, 1); + break; + case 0x01: + plat->flags |= + FIELD_PREP(STMMAC_FLAG_DISABLE_HALF_DUPLEX, 1); + break; + default: + break; + } + + return ret; +} + +static struct stmmac_pci_info loongson_gnet_pci_info = { + .setup = loongson_gnet_data, + .config = loongson_gnet_config, +}; + static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id *id) {@@ -318,9 +395,11 @@ staticSIMPLE_DEV_PM_OPS (loongson_dwmac_pm_ops, loongson_dwmac_suspend, loongson_dwmac_resume); #define PCI_DEVICE_ID_LOONGSON_GMAC 0x7a03 +#define PCI_DEVICE_ID_LOONGSON_GNET 0x7a13 static const struct pci_device_id loongson_dwmac_id_table[] = { { PCI_DEVICE_DATA(LOONGSON, GMAC, &loongson_gmac_pci_info) }, + { PCI_DEVICE_DATA(LOONGSON, GNET, &loongson_gnet_pci_info) }, {} }; MODULE_DEVICE_TABLE(pci, loongson_dwmac_id_table);diff --git
a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.cb/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.cindex8105ce47c6ad..d6939eb9a0d8100644drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c +5
-0@@ -420,6 +420,12 @@ stmmac_ethtool_set_link_ksettings(structnet_device *dev, return 0; } + if (FIELD_GET(STMMAC_FLAG_DISABLE_FORCE_1000, priv->plat->flags)) { + if (cmd->base.speed == SPEED_1000 && + cmd->base.autoneg != AUTONEG_ENABLE) + return -EOPNOTSUPP; + } + return phylink_ethtool_ksettings_set(priv->phylink, cmd); } diff --git a/include/linux/stmmac.h b/include/linux/stmmac.hindex
f07f79d50b06..067030cdb60f100644include/linux/stmmac.h +2
-0@@ -222,6 +222,8 @@ struct dwmac4_addrs { #define STMMAC_FLAG_EN_TX_LPI_CLOCKGATING BIT(11) #define STMMAC_FLAG_HWTSTAMP_CORRECT_LATENCY BIT(12) #define STMMAC_FLAG_HAS_LGMAC BIT(13) +#define STMMAC_FLAG_DISABLE_HALF_DUPLEX BIT(14) +#define STMMAC_FLAG_DISABLE_FORCE_1000 BIT(15) struct plat_stmmacenet_data { int bus_id;Signature · 1 line
2.31.4
Re: [PATCH net-next v7 7/9] net: stmmac: dwmac-loongson: Add GNET support
Quoted 13 lines · Serge Semin
Quoted 11 lines · Yanteng Si
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c: In function 'loongson_gnet_data':drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c:463:41: warning:
conversion from'long unsigned int' to 'unsigned int' changes value from '18446744073709551611' to '4294967291' [-Woverflow] 463 |
plat->mdio_bus_data->phy_mask= ~BIT(2); | ^Unfortunately, we don't have an unsigned int macro for BIT(nr).
Quoted 7 lines
Then the alternative ~(1 << 2) would be still more readable then the open-coded literal like
0xfffffffb. What would be even better than that:#define
LOONGSON_GNET_PHY_ADDR0x2
...plat->mdio_bus_data->phy_mask = ~(1 << LOONGSON_GNET_PHY_ADDR);
plat->mdio_bus_data->phy_mask = ~(u32)BIT(2);
would also work.
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
Re: [PATCH net-next v7 7/9] net: stmmac: dwmac-loongson: Add GNET support
Quoted 18 lines · Russell King (Oracle)
Quoted 17 lines · Serge Semin
Quoted 11 lines · Yanteng Si
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c: In function 'loongson_gnet_data':drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c:463:41: warning:
conversion from'long unsigned int' to 'unsigned int' changes value from '18446744073709551611' to '4294967291' [-Woverflow] 463 |
plat->mdio_bus_data->phy_mask= ~BIT(2); | ^Unfortunately, we don't have an unsigned int macro for BIT(nr).
Then the alternative ~(1 << 2) would be still more readable then the open-coded literal like
0xfffffffb. What would be even better than that:
Quoted 7 lines
Quoted 3 lines
#define
LOONGSON_GNET_PHY_ADDR0x2
...plat->mdio_bus_data->phy_mask = ~(1 << LOONGSON_GNET_PHY_ADDR);plat->mdio_bus_data->phy_mask = ~(u32)BIT(2);would also work.
Right, explicit type casting will work too. Something deep inside always inclines me to avoid explicit casts, although in this case your option may look more readable than the open-coded bitwise shift.
-Serge(y)
Quoted 5 lines
Signature · 3 lines
-- RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
Re: [PATCH net-next v7 7/9] net: stmmac: dwmac-loongson: Add GNET support
Quoted 21 lines · Serge Semin
Quoted 20 lines · Russell King (Oracle)
Quoted 19 lines · Serge Semin
Quoted 11 lines · Yanteng Si
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c: In function 'loongson_gnet_data':drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c:463:41: warning:
conversion from'long unsigned int' to 'unsigned int' changes value from '18446744073709551611' to '4294967291' [-Woverflow]
463 |plat->mdio_bus_data->phy_mask= ~BIT(2); | ^Unfortunately, we don't have an unsigned int macro for BIT(nr).
Then the alternative ~(1 << 2) would be still more readable then the open-coded literal like
0xfffffffb. What would be even better than that:#define
LOONGSON_GNET_PHY_ADDR0x2
...plat->mdio_bus_data->phy_mask = ~(1 << LOONGSON_GNET_PHY_ADDR);
Quoted 7 lines
Quoted 3 lines
plat->mdio_bus_data->phy_mask = ~(u32)BIT(2);would also work.
Right, explicit type casting will work too. Something deep inside always inclines me to avoid explicit casts, although in this case your option may look more readable than the open-coded bitwise shift.
OK!
Thanks,
Yanteng
Quoted 7 lines
-Serge(y)
Quoted 4 lines
Signature · 3 lines
-- RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
PATCH v7 8/9 net: stmmac: dwmac-loongson: Disable flow control for GMAC
In reply to Yanteng SiLoongson GMAC does not support Flow Control feature. Set flags to disable it.
--- drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c | 2 ++ drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 6 +++--- include/linux/stmmac.h | 1 + 3 files changed, 6 insertions(+), 3 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +2 -0
@@ -160,6 +160,8 @@ static int loongson_gmac_config(struct pci_dev *pdev,break ; } + plat->flags |=FIELD_PREP (STMMAC_FLAG_DISABLE_FLOW_CONTROL ,1 ); +return ret; }
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +3 -3
@@ -1236,9 +1236,9 @@ static int stmmac_phy_setup(struct stmmac_priv *priv)xpcs_get_interfaces (priv->hw->xpcs, priv->phylink_config.supported_interfaces); - priv->phylink_config.mac_capabilities =MAC_ASYM_PAUSE |MAC_SYM_PAUSE | -MAC_10FD |MAC_100FD | -MAC_1000FD ; + priv->phylink_config.mac_capabilities =MAC_10FD |MAC_100FD |MAC_1000FD ; +if (!FIELD_GET (STMMAC_FLAG_DISABLE_FLOW_CONTROL , priv->plat->flags)) + priv->phylink_config.mac_capabilities |=MAC_ASYM_PAUSE |MAC_SYM_PAUSE ;stmmac_set_half_duplex (priv);
include/linux/stmmac.h +1 -0
@@ -224,6 +224,7 @@ struct dwmac4_addrs {#define STMMAC_FLAG_HAS_LGMAC BIT(13)#define STMMAC_FLAG_DISABLE_HALF_DUPLEX BIT(14)#define STMMAC_FLAG_DISABLE_FORCE_1000 BIT(15) +#define STMMAC_FLAG_DISABLE_FLOW_CONTROL BIT(16)struct plat_stmmacenet_data {int bus_id;
Signature · 1 line
2.31.4
Re: [PATCH net-next v7 8/9] net: stmmac: dwmac-loongson: Disable flow control for GMAC
Quoted 17 lines · Yanteng Si
Loongson GMAC does not support Flow Control feature. Set flags to disable it.
Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c | 2 ++ drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 6 +++--- include/linux/stmmac.h | 1 + 3 files changed, 6 insertions(+), 3 deletions(-)drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +0
-0
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_gmac_config(struct pci_dev *pdev, · line 164
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +1
-0@@ -160,6 +160,8 @@ static int loongson_gmac_config(struct pci_dev *pdev,break ; } + plat->flags |=FIELD_PREP (STMMAC_FLAG_DISABLE_FLOW_CONTROL ,1 );
Why FIELD_PREP()-ing?
Quoted 9 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +1
-0+return ret; }drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +0
-0
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c static int stmmac_phy_setup(struct stmmac_priv *priv) · line 1241
Quoted 9 lines
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +2
-3@@ -1236,9 +1236,9 @@ static int stmmac_phy_setup(struct stmmac_priv *priv)xpcs_get_interfaces (priv->hw->xpcs, priv->phylink_config.supported_interfaces); - priv->phylink_config.mac_capabilities =MAC_ASYM_PAUSE |MAC_SYM_PAUSE | -MAC_10FD |MAC_100FD | -MAC_1000FD ; + priv->phylink_config.mac_capabilities =MAC_10FD |MAC_100FD |MAC_1000FD ; +if (!FIELD_GET (STMMAC_FLAG_DISABLE_FLOW_CONTROL , priv->plat->flags))
!(priv->plat->flags & STMMAC_FLAG_DISABLE_FLOW_CONTROL) ?
-Serge(y)
Quoted 19 lines
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +1
-0+ priv->phylink_config.mac_capabilities |=MAC_ASYM_PAUSE |MAC_SYM_PAUSE ;stmmac_set_half_duplex (priv);include/linux/stmmac.h +1
-0@@ -224,6 +224,7 @@ struct dwmac4_addrs {#define STMMAC_FLAG_HAS_LGMAC BIT(13)#define STMMAC_FLAG_DISABLE_HALF_DUPLEX BIT(14)#define STMMAC_FLAG_DISABLE_FORCE_1000 BIT(15) +#define STMMAC_FLAG_DISABLE_FLOW_CONTROL BIT(16)struct plat_stmmacenet_data {int bus_id;Signature · 1 line
2.31.4
Re: [PATCH net-next v7 8/9] net: stmmac: dwmac-loongson: Disable flow control for GMAC
Quoted 21 lines · Serge Semin
Quoted 20 lines · Yanteng Si
Loongson GMAC does not support Flow Control feature. Set flags to disable it.
Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c | 2 ++ drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 6 +++--- include/linux/stmmac.h | 1 + 3 files changed, 6 insertions(+), 3 deletions(-)drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +0
-0@@ -160,6 +160,8 @@ static int loongson_gmac_config(struct pci_dev *pdev,break ; }
Quoted 2 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_gmac_config(struct pci_dev *pdev, · line 163
Quoted 1 line
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +1
-0+ plat->flags |=FIELD_PREP (STMMAC_FLAG_DISABLE_FLOW_CONTROL ,1 );Why FIELD_PREP()-ing?
This is very early code and will be changed to:
plat->flags |= STMMAC_FLAG_DISABLE_FLOW_CONTROL;
Quoted 13 lines
Quoted 13 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +1
-0+return ret; }drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +0
-0@@ -1236,9 +1236,9 @@ static int stmmac_phy_setup(struct stmmac_priv *priv)xpcs_get_interfaces (priv->hw->xpcs, priv->phylink_config.supported_interfaces);
Quoted 6 lines
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c static int stmmac_phy_setup(struct stmmac_priv *priv) · line 1240
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +2
-3- priv->phylink_config.mac_capabilities =MAC_ASYM_PAUSE |MAC_SYM_PAUSE | -MAC_10FD |MAC_100FD | -MAC_1000FD ; + priv->phylink_config.mac_capabilities =MAC_10FD |MAC_100FD |MAC_1000FD ; +if (!FIELD_GET (STMMAC_FLAG_DISABLE_FLOW_CONTROL , priv->plat->flags))!(priv->plat->flags &
STMMAC_FLAG_DISABLE_FLOW_CONTROL) ?
OK!
Thanks,
Yanteng
Quoted 22 lines
-Serge(y)
Quoted 19 lines
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +1
-0+ priv->phylink_config.mac_capabilities |=MAC_ASYM_PAUSE |MAC_SYM_PAUSE ;stmmac_set_half_duplex (priv);include/linux/stmmac.h +1
-0@@ -224,6 +224,7 @@ struct dwmac4_addrs {#define STMMAC_FLAG_HAS_LGMAC BIT(13)#define STMMAC_FLAG_DISABLE_HALF_DUPLEX BIT(14)#define STMMAC_FLAG_DISABLE_FORCE_1000 BIT(15) +#define STMMAC_FLAG_DISABLE_FLOW_CONTROL BIT(16)struct plat_stmmacenet_data {int bus_id;Signature · 1 line
2.31.4
PATCH v7 9/9 net: stmmac: Disable coe for some Loongson GNET
In reply to Yanteng SiSome chips of Loongson GNET does not support coe, so disable them.
--- drivers/net/ethernet/stmicro/stmmac/hwif.c | 5 +++++ 1 file changed, 5 insertions(+)
drivers/net/ethernet/stmicro/stmmac/hwif.c +5 -0
@@ -73,6 +73,11 @@ static int stmmac_dwmac1_quirks(struct stmmac_priv *priv) mac->desc = &ndesc_ops; } +if (priv->synopsys_id ==DWLGMAC_CORE_1_00 ) { + priv->plat->tx_coe =0 ; + priv->plat->rx_coe =STMMAC_RX_COE_NONE ; + } +stmmac_dwmac_mode_quirk (priv);return 0 ; }
Signature · 1 line
2.31.4
Re: [PATCH net-next v7 9/9] net: stmmac: Disable coe for some Loongson GNET
Quoted 14 lines · Yanteng Si
Some chips of Loongson GNET does not support coe, so disable them.
Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- drivers/net/ethernet/stmicro/stmmac/hwif.c | 5 +++++ 1 file changed, 5 insertions(+)drivers/net/ethernet/stmicro/stmmac/hwif.c +0
-0
drivers/net/ethernet/stmicro/stmmac/hwif.c static int stmmac_dwmac1_quirks(struct stmmac_priv *priv) · line 79
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/hwif.c +4
-0@@ -73,6 +73,11 @@ static int stmmac_dwmac1_quirks(struct stmmac_priv *priv) mac->desc = &ndesc_ops; } +if (priv->synopsys_id ==DWLGMAC_CORE_1_00 ) { + priv->plat->tx_coe =0 ; + priv->plat->rx_coe =STMMAC_RX_COE_NONE ; + }
Couldn't this be done in dwmac-loongson.c?
-Serge(y)
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/hwif.c +1
-0+stmmac_dwmac_mode_quirk (priv);return 0 ; }Signature · 1 line
2.31.4
Re: [PATCH net-next v7 9/9] net: stmmac: Disable coe for some Loongson GNET
Quoted 18 lines · Serge Semin
Quoted 17 lines · Yanteng Si
Some chips of Loongson GNET does not support coe, so disable them.
Signed-off-by Yanteng Si <[email protected]>Signed-off-by Feiyang Chen <[email protected]>Signed-off-by Yinggang Gu <[email protected]>--- drivers/net/ethernet/stmicro/stmmac/hwif.c | 5 +++++ 1 file changed, 5 insertions(+)drivers/net/ethernet/stmicro/stmmac/hwif.c +0
-0@@ -73,6 +73,11 @@ static int stmmac_dwmac1_quirks(struct stmmac_priv *priv) mac->desc = &ndesc_ops; }
Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/hwif.c static int stmmac_dwmac1_quirks(struct stmmac_priv *priv) · line 79
Quoted 4 lines
drivers/net/ethernet/stmicro/stmmac/hwif.c +4
-0+if (priv->synopsys_id ==DWLGMAC_CORE_1_00 ) { + priv->plat->tx_coe =0 ; + priv->plat->rx_coe =STMMAC_RX_COE_NONE ; + }Couldn't this be done in
dwmac-loongson.c?
Sorry for the late reply, I have been busy with patches 4 and 5.
I think I can give you a definite answer: This is possible, just like
the method you mentioned in patch 5, I only need to
overwrite ld->dwlgmac_dma_ops.get_hw_feature.
Thanks,
Yanteng
Quoted 10 lines
-Serge(y)
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/hwif.c +1
-0+stmmac_dwmac_mode_quirk (priv);return 0 ; }Signature · 1 line
2.31.4