Skip to contentSkip to conversation

stmmac: Add Loongson platform support

PATCH Superseded Yanteng Si 3 participants 28 messages Jul 9, 2024 – Jul 19, 2024

Subsystems (5)

v14 of 17 Superseded Latest is v17 →

lore
Share & tools
lore

Yanteng Si

author
#0 lore raw

v14 cover stmmac: Add Loongson platform support

v14:

Because Loongson GMAC can be also found with the 8-channels AV feature
enabled, we'll need to reconsider the patches logic and thus the
commit logs too. As Serge's comments and Russell's comments:
[PATCH net-next v14 01/15] net: stmmac: Move the atds flag to the stmmac_dma_cfg structure [PATCH net-next v14 02/15] net: stmmac: Add multi-channel support
[PATCH net-next v14 03/15] net: stmmac: Export dwmac1000_dma_ops
[PATCH net-next v14 04/15] net: stmmac: dwmac-loongson: Drop duplicated hash-based filter size init [PATCH net-next v14 05/15] net: stmmac: dwmac-loongson: Drop pci_enable/disable_msi calls [PATCH net-next v14 06/15] net: stmmac: dwmac-loongson: Use PCI_DEVICE_DATA() macro for device identification [PATCH net-next v14 07/15] net: stmmac: dwmac-loongson: Detach GMAC-specific platform data init +-> Init the plat_stmmacenet_data::{tx_queues_to_use,rx_queues_to_use}
in the loongson_gmac_data() method.
[PATCH net-next v14 08/15] net: stmmac: dwmac-loongson: Init ref and PTP clocks rate
[PATCH net-next v14 09/15] net: stmmac: dwmac-loongson: Add phy_interface for Loongson GMAC [PATCH net-next v14 10/15] net: stmmac: dwmac-loongson: Introduce PCI device info data
+-> Make sure the setup() method is called after the pci_enable_device()
invocation.
[PATCH net-next v14 11/15] net: stmmac: dwmac-loongson: Add DT-less GMAC PCI-device support +-> Introduce the loongson_dwmac_dt_config() method here instead of
doing that in a separate patch.
+-> Add loongson_dwmac_acpi_config() which would just get the IRQ from

    the pdev->irq field and make sure it is valid.

[PATCH net-next v14 12/15] net: stmmac: Fixed failure to set network speed to 1000. +-> Drop the patch as Russell's comments, At the same time, he provided another
better repair suggestion, and I decided to send it separately after the patch set was merged. See:
<https://lore.kernel.org/netdev/[email protected]/>
[PATCH net-next v14 13/15] net: stmmac: dwmac-loongson: Add Loongson Multi-channels GMAC support +-> This is former "net: stmmac: dwmac-loongson: Add Loongson GNET
support" patch, but which adds the support of the Loongson GMAC with the 8-channels AV-feature available.
+-> loongson_dwmac_intx_config() shall be dropped due to the
loongson_dwmac_acpi_config() method added in the PATCH 11/15.
+-> Make sure loongson_data::loongson_id is initialized before the
stmmac_pci_info::setup() is called.
+-> Move the rx_queues_to_use/tx_queues_to_use and coe_unsupported
fields initialization to the loongson_gmac_data() method.
+-> As before, call the loongson_dwmac_msi_config() method if the multi-channels
Loongson MAC has been detected.
+-> Move everything GNET-specific to the next patch.
[PATCH net-next v14 14/15] net: stmmac: dwmac-loongson: Add Loongson GNET support +-> Everything Loonsgson GNET-specific is supposed to be added in the
framework of this patch:
+ PCI_DEVICE_ID_LOONGSON_GNET macro
+ loongson_gnet_fix_speed() method
+ loongson_gnet_data() method
+ loongson_gnet_pci_info data
+ The GNET-specific part of the loongson_dwmac_setup() method.
+ ...
[PATCH net-next v14 15/15] net: stmmac: dwmac-loongson: Add loongson module author

Other's:
Pick Serge's Reviewed-by tag.

v13:

* Sorry, we have clarified some things in the past 10 days. I did not give you a clear reply to the following questions in v12, so I need to reply again:

1. The current LS2K2000 also have a GMAC(and two GNET) that supports 8 channels, so we have to reconsider the initialization of tx/rx_queues_to_use into probe();

2. In v12, we disagreed on the loongson_dwmac_msi_config method, but I changed

    it based on Serge's comments(If I understand correctly):
	if (dev_of_node(&pdev->dev)) {
		ret = loongson_dwmac_dt_config(pdev, plat, &res);
	}

	if (ld->loongson_id == DWMAC_CORE_LS2K2000) {
		ret = loongson_dwmac_msi_config(pdev, plat, &res);
	} else {
		ret = loongson_dwmac_intx_config(pdev, plat, &res);
	}

3. Our priv->dma_cap.pcs is false, so let's use PHY_INTERFACE_MODE_NA;

4. Our GMAC does not support Delay, so let's use PHY_INTERFACE_MODE_RGMII_ID, the current dts is wrong, a fix patch will be sent to the LoongArch list later.

Others:
* Re-split a part of the patch (it seems we do this with every version);
* Copied Serge's comments into the commit message of patch;
* Fixed the stmmac_dma_operation_mode() method;
* Changed some code comments.

v12:
* The biggest change is the re-splitting of patches.
* Add a "gmac_version" in loongson_data, then we only read it once in the _probe().
* Drop Serge's patch.
* Rebase to the latest code state.
* Fixed the gnet commit message.

v11:
* Break loongson_phylink_get_caps(), fix bad logic.
* Remove a unnecessary ";".
* Remove some unnecessary "{}".
* add a blank.
* Move the code of fix _force_1000 to patch 6/6.

The main changes occur in these two functions:
loongson_dwmac_probe();
loongson_dwmac_setup();

v10:
As Andrew's comment:
* Add a #define for the 0x37.
* Add a #define for Port Select.

others:
* Pick Serge's patch, This patch resulted from the process of reviewing our patch set.
* Based on Serge's patch, modify our loongson_phylink_get_caps().
* Drop patch 3/6, we need mac_interface.
* Adjusted the code layout of gnet patch.
* Corrected several errata in commit message.
* Move DISABLE_FORCE flag to loongson_gnet_data().

v9:
We have not provided a detailed list of equipment for a long time, and I apologize for this. During this period, I have collected some information and now present it to you, hoping to alleviate the pressure of review.

1. IP core
We now have two types of IP cores, one is 0x37, similar to dwmac1000; The other is 0x10. Compared to 0x37, we split several DMA registers from one to two, and it is not worth adding a new entry for this. According to Serge's comment, we made these devices work by overwriting priv->synopsys_id = 0x37 and mac->dma = <LS_dma_ops>.

1.1. Some more detailed information
The number of DMA channels for 0x37 is 1; The number of DMA channels for 0x10 is 8. Except for channel 0, otherchannels do not support sending hardware checksums. Supported AV features are Qav, Qat, and Qas, and the rest are consistent with 3.73.

2. DEVICE
We have two types of devices,
one is GMAC, which only has a MAC chip inside and needs an external PHY chip;
the other is GNET, which integrates both MAC and PHY chips inside.

2.1. Some more detailed information
GMAC device: LS7A1000, LS2K1000, these devices do not support any pause mode.
gnet device: LS7A2000, LS2K2000, the chip connection between the mac and
phy of these devices is not normal and requires two rounds of negotiation; LS7A2000 does not support half-duplex and
multi-channel;
to enable multi-channel on LS2K2000, you need to turn off
hardware checksum.
**Note**: Only the LS2K2000's IP core is 0x10, while the IP cores of other devices are 0x37.

3. TABLE

device    type    pci_id    ip_core
ls7a1000  gmac    7a03      0x35/0x37
ls2k1000  gmac    7a03      0x35/0x37
ls7a2000  gnet    7a13      0x37
ls2k2000  gnet    7a13      0x10

-----------------------------------------------
Changes:

* passed the CI
<https://github.com/linux-netdev/nipa/blob/main/tests/patch/checkpatch
/checkpatch.sh>
* reverse xmas tree order.
* Silence build warning.
* Re-split the patch.
* Add more detailed commit message.
* Add more code comment.
* Reduce modification of generic code.
* using the GNET-specific prefix.
* define a new macro for the GNET MAC.
* Use an easier way to overwrite mac.
* Removed some useless printk.

v8:
* The biggest change is according to Serge's comment in the previous edition:
Seeing the patch in the current state would overcomplicate the generic code and the only functions you need to update are dwmac_dma_interrupt()
dwmac1000_dma_init_channel()
you can have these methods re-defined with all the Loongson GNET specifics in the low-level platform driver (dwmac-loongson.c). After that you can just override the mac_device_info.dma pointer with a fixed stmmac_dma_ops descriptor. Here is what should be done for that:

1. Keep the Patch 4/9 with my comments fixed. First it will be partly useful for your GNET device. Second in general it's a correct implementation of the normal DW GMAC v3.x multi-channels feature and will be useful for the DW GMACs with that feature enabled.

2. Create the Loongson GNET-specific stmmac_dma_ops.dma_interrupt()
stmmac_dma_ops.init_chan()
methods in the dwmac-loongson.c driver. Don't forget to move all the Loongson-specific macros from dwmac_dma.h to dwmac-loongson.c.

3. Create a Loongson GNET-specific platform setup method with the next semantics:
+ allocate stmmac_dma_ops instance and initialize it with dwmac1000_dma_ops.
+ override the stmmac_dma_ops.{dma_interrupt, init_chan} with the pointers to the methods defined in 2.
+ allocate mac_device_info instance and initialize the mac_device_info.dma field with a pointer to the new stmmac_dma_ops instance.
+ call dwmac1000_setup() or initialize mac_device_info in a way it's done in dwmac1000_setup() (the later might be better so you wouldn't need to export the dwmac1000_setup() function).
+ override stmmac_priv.synopsys_id with a correct value.

4. Initialize plat_stmmacenet_data.setup() with the pointer to the method created in 3.

* Others:
Re-split the patch.
Passed checkpatch.pl test.

v7:
* Refer to andrew's suggestion:
- Add DMA_INTR_ENA_NIE_RX and DMA_INTR_ENA_NIE_TX #define's, etc.

* Others:
- Using --subject-prefix="PATCH net-next vN" to indicate that the patches are for the networking tree.
- Rebase to the latest networking tree:
<git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git>

v6:

* Refer to Serge's suggestion:
- Add new platform feature flag:

    include/linux/stmmac.h:
    +#define STMMAC_FLAG_HAS_LGMAC			BIT(13)

- Add the IRQs macros specific to the Loongson Multi-channels GMAC:

     drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h:
     +#define DMA_INTR_ENA_NIE_LOONGSON 0x00060000      /* ...*/
     #define DMA_INTR_ENA_NIE 0x00010000	/* Normal Summary */
     ...

- Drop all of redundant changes that don't require the prototypes being converted to accepting the stmmac_priv pointer.

* Refer to andrew's suggestion:
- Drop white space changes.
- break patch up into lots of smaller parts.
Some small patches have been put into another series as a preparation see <https://lore.kernel.org/loongarch/[email protected]/T/#t>

*note* : This series of patches relies on the three small patches above.
* others
- Drop irq_flags changes.
- Changed patch order.

v4 -> v5:

* Remove an ugly and useless patch (fix channel number).
* Remove the non-standard dma64 driver code, and also remove the HWIF entries, since the associated custom callbacks no longer exist.
* Refer to Serge's suggestion: Update the dwmac1000_dma.c to support the multi-DMA-channels controller setup.

See:
v4: <https://lore.kernel.org/loongarch/[email protected]/>
v3: <https://lore.kernel.org/loongarch/[email protected]/>
v2: <https://lore.kernel.org/loongarch/[email protected]/>
v1: <https://lore.kernel.org/loongarch/[email protected]/>

Yanteng Si (14):
net: stmmac: Move the atds flag to the stmmac_dma_cfg structure
net: stmmac: Add multi-channel support
net: stmmac: Export dwmac1000_dma_ops
net: stmmac: dwmac-loongson: Drop duplicated hash-based filter size
init
net: stmmac: dwmac-loongson: Drop pci_enable/disable_msi calls
net: stmmac: dwmac-loongson: Use PCI_DEVICE_DATA() macro for device
identification
net: stmmac: dwmac-loongson: Detach GMAC-specific platform data init
net: stmmac: dwmac-loongson: Init ref and PTP clocks rate
net: stmmac: dwmac-loongson: Add phy_interface for Loongson GMAC
net: stmmac: dwmac-loongson: Introduce PCI device info data
net: stmmac: dwmac-loongson: Add DT-less GMAC PCI-device support
net: stmmac: dwmac-loongson: Add Loongson Multi-channels GMAC support
net: stmmac: dwmac-loongson: Add Loongson GNET support
net: stmmac: dwmac-loongson: Add loongson module author

 drivers/net/ethernet/stmicro/stmmac/common.h  |   1 +
 .../ethernet/stmicro/stmmac/dwmac-loongson.c  | 572 ++++++++++++++++--
 .../net/ethernet/stmicro/stmmac/dwmac-sun8i.c |   4 +-
 .../ethernet/stmicro/stmmac/dwmac1000_dma.c   |  35 +-
 .../ethernet/stmicro/stmmac/dwmac100_dma.c    |   2 +-
 .../net/ethernet/stmicro/stmmac/dwmac4_dma.c  |   2 +-
 .../net/ethernet/stmicro/stmmac/dwmac_dma.h   |  27 +-
 .../net/ethernet/stmicro/stmmac/dwmac_lib.c   |  30 +-
 .../ethernet/stmicro/stmmac/dwxgmac2_dma.c    |   2 +-
 drivers/net/ethernet/stmicro/stmmac/hwif.h    |   5 +-
 .../net/ethernet/stmicro/stmmac/stmmac_main.c |  19 +-
 include/linux/stmmac.h                        |   1 +
 12 files changed, 587 insertions(+), 113 deletions(-)
Signature · 1 line
2.31.4
author
#1 lore raw

PATCH v14 1/14 net: stmmac: Move the atds flag to the stmmac_dma_cfg structure

ATDS (Alternate Descriptor Size) is a part of the DMA Bus Mode configs (together with PBL, ALL, EME, etc) of the DW GMAC controllers. Seeing it's not changed at runtime but is activated as long as the IP-core has it supported (at least due to the Type 2 Full Checksum Offload Engine feature), move the respective parameter from the stmmac_dma_ops::init() callback argument to the stmmac_dma_cfg structure, which already have the rest of the DMA-related configs defined.

Besides the being added in the next commit DW GMAC multi-channels support will require to add the stmmac_dma_ops::init_chan() callback and have the ATDS flag set/cleared for each channel in there. Having the atds-flag in the stmmac_dma_cfg structure will make the parameter accessible from stmmac_dma_ops::init_chan() callback too.

---
 drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c   | 2 +-
 drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c | 4 ++--
 drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c  | 2 +-
 drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c    | 2 +-
 drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c  | 2 +-
 drivers/net/ethernet/stmicro/stmmac/hwif.h          | 3 +--
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c   | 5 ++---
 include/linux/stmmac.h                              | 1 +
 8 files changed, 10 insertions(+), 11 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +1 -1
index e1b761dcfa1d..d87079016952 100644
@@ -299,7 +299,7 @@ static int sun8i_dwmac_dma_reset(void __iomem *ioaddr)
  * Called from stmmac via stmmac_dma_ops->init
  */
 static void sun8i_dwmac_dma_init(void __iomem *ioaddr,
-				 struct stmmac_dma_cfg *dma_cfg, int atds)
+				 struct stmmac_dma_cfg *dma_cfg)
 {
 	writel(EMAC_RX_INT | EMAC_TX_INT, ioaddr + EMAC_INT_EN);
 	writel(0x1FFFFFF, ioaddr + EMAC_INT_STA);
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +2 -2
index adccdd816ea9..984b809105af 100644
@@ -71,7 +71,7 @@ static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi)
 }
 
 static void dwmac1000_dma_init(void __iomem *ioaddr,
-			       struct stmmac_dma_cfg *dma_cfg, int atds)
+			       struct stmmac_dma_cfg *dma_cfg)
 {
 	u32 value = readl(ioaddr + DMA_BUS_MODE);
 	int txpbl = dma_cfg->txpbl ?: dma_cfg->pbl;
@@ -98,7 +98,7 @@ static void dwmac1000_dma_init(void __iomem *ioaddr,
 	if (dma_cfg->mixed_burst)
 		value |= DMA_BUS_MODE_MB;
 
-	if (atds)
+	if (dma_cfg->atds)
 		value |= DMA_BUS_MODE_ATDS;
 
 	if (dma_cfg->aal)
drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c +1 -1
index b402fb54f613..82957db47c99 100644
@@ -19,7 +19,7 @@
 #include "dwmac_dma.h"
 
 static void dwmac100_dma_init(void __iomem *ioaddr,
-			      struct stmmac_dma_cfg *dma_cfg, int atds)
+			      struct stmmac_dma_cfg *dma_cfg)
 {
 	/* Enable Application Access by writing to DMA CSR0 */
 	writel(DMA_BUS_MODE_DEFAULT | (dma_cfg->pbl << DMA_BUS_MODE_PBL_SHIFT),
drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c +1 -1
index 84d3a8551b03..e0165358c4ac 100644
@@ -153,7 +153,7 @@ static void dwmac410_dma_init_channel(struct stmmac_priv *priv,
 }
 
 static void dwmac4_dma_init(void __iomem *ioaddr,
-			    struct stmmac_dma_cfg *dma_cfg, int atds)
+			    struct stmmac_dma_cfg *dma_cfg)
 {
 	u32 value = readl(ioaddr + DMA_SYS_BUS_MODE);
 
drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c +1 -1
index dd2ab6185c40..7840bc403788 100644
@@ -20,7 +20,7 @@ static int dwxgmac2_dma_reset(void __iomem *ioaddr)
 }
 
 static void dwxgmac2_dma_init(void __iomem *ioaddr,
-			      struct stmmac_dma_cfg *dma_cfg, int atds)
+			      struct stmmac_dma_cfg *dma_cfg)
 {
 	u32 value = readl(ioaddr + XGMAC_DMA_SYSBUS_MODE);
 
drivers/net/ethernet/stmicro/stmmac/hwif.h +1 -2
index 97934ccba5b1..dc6dbb6ce50a 100644
@@ -175,8 +175,7 @@ struct dma_features;
 struct stmmac_dma_ops {
 	/* DMA core initialization */
 	int (*reset)(void __iomem *ioaddr);
-	void (*init)(void __iomem *ioaddr, struct stmmac_dma_cfg *dma_cfg,
-		     int atds);
+	void (*init)(void __iomem *ioaddr, struct stmmac_dma_cfg *dma_cfg);
 	void (*init_chan)(struct stmmac_priv *priv, void __iomem *ioaddr,
 			  struct stmmac_dma_cfg *dma_cfg, u32 chan);
 	void (*init_rx_chan)(struct stmmac_priv *priv, void __iomem *ioaddr,
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +2 -3
index 4b6a359e5a94..5aa0c776757d 100644
@@ -3003,7 +3003,6 @@ static int stmmac_init_dma_engine(struct stmmac_priv *priv)
 	struct stmmac_rx_queue *rx_q;
 	struct stmmac_tx_queue *tx_q;
 	u32 chan = 0;
-	int atds = 0;
 	int ret = 0;
 
 	if (!priv->plat->dma_cfg || !priv->plat->dma_cfg->pbl) {
@@ -3012,7 +3011,7 @@ static int stmmac_init_dma_engine(struct stmmac_priv *priv)
 	}
 
 	if (priv->extend_desc && (priv->mode == STMMAC_RING_MODE))
-		atds = 1;
+		priv->plat->dma_cfg->atds = 1;
 
 	ret = stmmac_reset(priv, priv->ioaddr);
 	if (ret) {
@@ -3021,7 +3020,7 @@ static int stmmac_init_dma_engine(struct stmmac_priv *priv)
 	}
 
 	/* DMA Configuration */
-	stmmac_dma_init(priv, priv->ioaddr, priv->plat->dma_cfg, atds);
+	stmmac_dma_init(priv, priv->ioaddr, priv->plat->dma_cfg);
 
 	if (priv->plat->axi)
 		stmmac_axi(priv, priv->ioaddr, priv->plat->axi);
include/linux/stmmac.h +1 -0
index 84e13bd5df28..338991c08f00 100644
@@ -100,6 +100,7 @@ struct stmmac_dma_cfg {
 	bool eame;
 	bool multi_msi_en;
 	bool dche;
+	bool atds;
 };
 
 #define AXI_BLEN	7
Signature · 1 line
2.31.4
author
#2 lore raw

PATCH v14 2/14 net: stmmac: Add multi-channel support

In reply to Yanteng Si

DW GMAC v3.73 can be equipped with the Audio Video (AV) feature which enables transmission of time-sensitive traffic over bridged local area networks (DWC Ethernet QoS Product). In that case there can be up to two additional DMA-channels available with no Tx COE support (unless there is vendor-specific IP-core alterations). Each channel is implemented as a separate Control and Status register (CSR) for managing the transmit and receive functions, descriptor handling, and interrupt handling.

Add the multi-channels DW GMAC controllers support just by making sure the already implemented DMA-configs are performed on the per-channel basis.

Note the only currently known instance of the multi-channel DW GMAC IP-core is the LS2K2000 GNET controller, which has been released with the vendor-specific feature extension of having eight DMA-channels. The device support will be added in one of the following up commits.

---
 .../net/ethernet/stmicro/stmmac/dwmac-sun8i.c |  2 +-
 .../ethernet/stmicro/stmmac/dwmac1000_dma.c   | 32 ++++++++++---------
 .../net/ethernet/stmicro/stmmac/dwmac_dma.h   | 27 +++++++++++++++-
 .../net/ethernet/stmicro/stmmac/dwmac_lib.c   | 30 ++++++++---------
 drivers/net/ethernet/stmicro/stmmac/hwif.h    |  2 +-
 .../net/ethernet/stmicro/stmmac/stmmac_main.c | 14 ++++----
 6 files changed, 68 insertions(+), 39 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +1 -1
index d87079016952..cc93f73a380e 100644
@@ -395,7 +395,7 @@ static void sun8i_dwmac_dma_start_tx(struct stmmac_priv *priv,
 	writel(v, ioaddr + EMAC_TX_CTL1);
 }
 
-static void sun8i_dwmac_enable_dma_transmission(void __iomem *ioaddr)
+static void sun8i_dwmac_enable_dma_transmission(void __iomem *ioaddr, u32 chan)
 {
 	u32 v;
 
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +17 -15
index 984b809105af..b3d7eff53b18 100644
@@ -70,15 +70,17 @@ static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi)
 	writel(value, ioaddr + DMA_AXI_BUS_MODE);
 }
 
-static void dwmac1000_dma_init(void __iomem *ioaddr,
-			       struct stmmac_dma_cfg *dma_cfg)
+static void dwmac1000_dma_init_channel(struct stmmac_priv *priv,
+				       void __iomem *ioaddr,
+				       struct stmmac_dma_cfg *dma_cfg, u32 chan)
 {
-	u32 value = readl(ioaddr + DMA_BUS_MODE);
 	int txpbl = dma_cfg->txpbl ?: dma_cfg->pbl;
 	int rxpbl = dma_cfg->rxpbl ?: dma_cfg->pbl;
+	u32 value;
 
-	/*
-	 * Set the DMA PBL (Programmable Burst Length) mode.
+	value = readl(ioaddr + DMA_CHAN_BUS_MODE(chan));
+
+	/* Set the DMA PBL (Programmable Burst Length) mode.
 	 *
 	 * Note: before stmmac core 3.50 this mode bit was 4xPBL, and
 	 * post 3.5 mode bit acts as 8*PBL.
@@ -104,10 +106,10 @@ static void dwmac1000_dma_init(void __iomem *ioaddr,
 	if (dma_cfg->aal)
 		value |= DMA_BUS_MODE_AAL;
 
-	writel(value, ioaddr + DMA_BUS_MODE);
+	writel(value, ioaddr + DMA_CHAN_BUS_MODE(chan));
 
 	/* Mask interrupts by writing to CSR7 */
-	writel(DMA_INTR_DEFAULT_MASK, ioaddr + DMA_INTR_ENA);
+	writel(DMA_INTR_DEFAULT_MASK, ioaddr + DMA_CHAN_INTR_ENA(chan));
 }
 
 static void dwmac1000_dma_init_rx(struct stmmac_priv *priv,
@@ -116,7 +118,7 @@ static void dwmac1000_dma_init_rx(struct stmmac_priv *priv,
 				  dma_addr_t dma_rx_phy, u32 chan)
 {
 	/* RX descriptor base address list must be written into DMA CSR3 */
-	writel(lower_32_bits(dma_rx_phy), ioaddr + DMA_RCV_BASE_ADDR);
+	writel(lower_32_bits(dma_rx_phy), ioaddr + DMA_CHAN_RCV_BASE_ADDR(chan));
 }
 
 static void dwmac1000_dma_init_tx(struct stmmac_priv *priv,
@@ -125,7 +127,7 @@ static void dwmac1000_dma_init_tx(struct stmmac_priv *priv,
 				  dma_addr_t dma_tx_phy, u32 chan)
 {
 	/* TX descriptor base address list must be written into DMA CSR4 */
-	writel(lower_32_bits(dma_tx_phy), ioaddr + DMA_TX_BASE_ADDR);
+	writel(lower_32_bits(dma_tx_phy), ioaddr + DMA_CHAN_TX_BASE_ADDR(chan));
 }
 
 static u32 dwmac1000_configure_fc(u32 csr6, int rxfifosz)
@@ -153,7 +155,7 @@ static void dwmac1000_dma_operation_mode_rx(struct stmmac_priv *priv,
 					    void __iomem *ioaddr, int mode,
 					    u32 channel, int fifosz, u8 qmode)
 {
-	u32 csr6 = readl(ioaddr + DMA_CONTROL);
+	u32 csr6 = readl(ioaddr + DMA_CHAN_CONTROL(channel));
 
 	if (mode == SF_DMA_MODE) {
 		pr_debug("GMAC: enable RX store and forward mode\n");
@@ -175,14 +177,14 @@ static void dwmac1000_dma_operation_mode_rx(struct stmmac_priv *priv,
 	/* Configure flow control based on rx fifo size */
 	csr6 = dwmac1000_configure_fc(csr6, fifosz);
 
-	writel(csr6, ioaddr + DMA_CONTROL);
+	writel(csr6, ioaddr + DMA_CHAN_CONTROL(channel));
 }
 
 static void dwmac1000_dma_operation_mode_tx(struct stmmac_priv *priv,
 					    void __iomem *ioaddr, int mode,
 					    u32 channel, int fifosz, u8 qmode)
 {
-	u32 csr6 = readl(ioaddr + DMA_CONTROL);
+	u32 csr6 = readl(ioaddr + DMA_CHAN_CONTROL(channel));
 
 	if (mode == SF_DMA_MODE) {
 		pr_debug("GMAC: enable TX store and forward mode\n");
@@ -209,7 +211,7 @@ static void dwmac1000_dma_operation_mode_tx(struct stmmac_priv *priv,
 			csr6 |= DMA_CONTROL_TTC_256;
 	}
 
-	writel(csr6, ioaddr + DMA_CONTROL);
+	writel(csr6, ioaddr + DMA_CHAN_CONTROL(channel));
 }
 
 static void dwmac1000_dump_dma_regs(struct stmmac_priv *priv,
@@ -271,12 +273,12 @@ static int dwmac1000_get_hw_feature(void __iomem *ioaddr,
 static void dwmac1000_rx_watchdog(struct stmmac_priv *priv,
 				  void __iomem *ioaddr, u32 riwt, u32 queue)
 {
-	writel(riwt, ioaddr + DMA_RX_WATCHDOG);
+	writel(riwt, ioaddr + DMA_CHAN_RX_WATCHDOG(queue));
 }
 
 const struct stmmac_dma_ops dwmac1000_dma_ops = {
 	.reset = dwmac_dma_reset,
-	.init = dwmac1000_dma_init,
+	.init_chan = dwmac1000_dma_init_channel,
 	.init_rx_chan = dwmac1000_dma_init_rx,
 	.init_tx_chan = dwmac1000_dma_init_tx,
 	.axi = dwmac1000_dma_axi,
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +26 -1
index 72672391675f..5d9c18f5bbf5 100644
@@ -22,6 +22,31 @@
 #define DMA_INTR_ENA		0x0000101c	/* Interrupt Enable */
 #define DMA_MISSED_FRAME_CTR	0x00001020	/* Missed Frame Counter */
 
+/* Following DMA defines are channels oriented */
+#define DMA_CHAN_BASE_OFFSET			0x100
+
+static inline u32 dma_chan_base_addr(u32 base, u32 chan)
+{
+	return base + chan * DMA_CHAN_BASE_OFFSET;
+}
+
+#define DMA_CHAN_BUS_MODE(chan)	dma_chan_base_addr(DMA_BUS_MODE, chan)
+#define DMA_CHAN_XMT_POLL_DEMAND(chan)	\
+				dma_chan_base_addr(DMA_XMT_POLL_DEMAND, chan)
+#define DMA_CHAN_RCV_POLL_DEMAND(chan)	\
+				dma_chan_base_addr(DMA_RCV_POLL_DEMAND, chan)
+#define DMA_CHAN_RCV_BASE_ADDR(chan)	\
+				dma_chan_base_addr(DMA_RCV_BASE_ADDR, chan)
+#define DMA_CHAN_TX_BASE_ADDR(chan)	\
+				dma_chan_base_addr(DMA_TX_BASE_ADDR, chan)
+#define DMA_CHAN_STATUS(chan)	dma_chan_base_addr(DMA_STATUS, chan)
+#define DMA_CHAN_CONTROL(chan)	dma_chan_base_addr(DMA_CONTROL, chan)
+#define DMA_CHAN_INTR_ENA(chan)	dma_chan_base_addr(DMA_INTR_ENA, chan)
+#define DMA_CHAN_MISSED_FRAME_CTR(chan)	\
+				dma_chan_base_addr(DMA_MISSED_FRAME_CTR, chan)
+#define DMA_CHAN_RX_WATCHDOG(chan)	\
+				dma_chan_base_addr(DMA_RX_WATCHDOG, chan)
+
 /* SW Reset */
 #define DMA_BUS_MODE_SFT_RESET	0x00000001	/* Software Reset */
 
@@ -152,7 +177,7 @@
 #define NUM_DWMAC1000_DMA_REGS	23
 #define NUM_DWMAC4_DMA_REGS	27
 
-void dwmac_enable_dma_transmission(void __iomem *ioaddr);
+void dwmac_enable_dma_transmission(void __iomem *ioaddr, u32 chan);
 void dwmac_enable_dma_irq(struct stmmac_priv *priv, void __iomem *ioaddr,
 			  u32 chan, bool rx, bool tx);
 void dwmac_disable_dma_irq(struct stmmac_priv *priv, void __iomem *ioaddr,
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +15 -15
index 85e18f9a22f9..4846bf49c576 100644
@@ -28,65 +28,65 @@ int dwmac_dma_reset(void __iomem *ioaddr)
 }
 
 /* CSR1 enables the transmit DMA to check for new descriptor */
-void dwmac_enable_dma_transmission(void __iomem *ioaddr)
+void dwmac_enable_dma_transmission(void __iomem *ioaddr, u32 chan)
 {
-	writel(1, ioaddr + DMA_XMT_POLL_DEMAND);
+	writel(1, ioaddr + DMA_CHAN_XMT_POLL_DEMAND(chan));
 }
 
 void dwmac_enable_dma_irq(struct stmmac_priv *priv, void __iomem *ioaddr,
 			  u32 chan, bool rx, bool tx)
 {
-	u32 value = readl(ioaddr + DMA_INTR_ENA);
+	u32 value = readl(ioaddr + DMA_CHAN_INTR_ENA(chan));
 
 	if (rx)
 		value |= DMA_INTR_DEFAULT_RX;
 	if (tx)
 		value |= DMA_INTR_DEFAULT_TX;
 
-	writel(value, ioaddr + DMA_INTR_ENA);
+	writel(value, ioaddr + DMA_CHAN_INTR_ENA(chan));
 }
 
 void dwmac_disable_dma_irq(struct stmmac_priv *priv, void __iomem *ioaddr,
 			   u32 chan, bool rx, bool tx)
 {
-	u32 value = readl(ioaddr + DMA_INTR_ENA);
+	u32 value = readl(ioaddr + DMA_CHAN_INTR_ENA(chan));
 
 	if (rx)
 		value &= ~DMA_INTR_DEFAULT_RX;
 	if (tx)
 		value &= ~DMA_INTR_DEFAULT_TX;
 
-	writel(value, ioaddr + DMA_INTR_ENA);
+	writel(value, ioaddr + DMA_CHAN_INTR_ENA(chan));
 }
 
 void dwmac_dma_start_tx(struct stmmac_priv *priv, void __iomem *ioaddr,
 			u32 chan)
 {
-	u32 value = readl(ioaddr + DMA_CONTROL);
+	u32 value = readl(ioaddr + DMA_CHAN_CONTROL(chan));
 	value |= DMA_CONTROL_ST;
-	writel(value, ioaddr + DMA_CONTROL);
+	writel(value, ioaddr + DMA_CHAN_CONTROL(chan));
 }
 
 void dwmac_dma_stop_tx(struct stmmac_priv *priv, void __iomem *ioaddr, u32 chan)
 {
-	u32 value = readl(ioaddr + DMA_CONTROL);
+	u32 value = readl(ioaddr + DMA_CHAN_CONTROL(chan));
 	value &= ~DMA_CONTROL_ST;
-	writel(value, ioaddr + DMA_CONTROL);
+	writel(value, ioaddr + DMA_CHAN_CONTROL(chan));
 }
 
 void dwmac_dma_start_rx(struct stmmac_priv *priv, void __iomem *ioaddr,
 			u32 chan)
 {
-	u32 value = readl(ioaddr + DMA_CONTROL);
+	u32 value = readl(ioaddr + DMA_CHAN_CONTROL(chan));
 	value |= DMA_CONTROL_SR;
-	writel(value, ioaddr + DMA_CONTROL);
+	writel(value, ioaddr + DMA_CHAN_CONTROL(chan));
 }
 
 void dwmac_dma_stop_rx(struct stmmac_priv *priv, void __iomem *ioaddr, u32 chan)
 {
-	u32 value = readl(ioaddr + DMA_CONTROL);
+	u32 value = readl(ioaddr + DMA_CHAN_CONTROL(chan));
 	value &= ~DMA_CONTROL_SR;
-	writel(value, ioaddr + DMA_CONTROL);
+	writel(value, ioaddr + DMA_CHAN_CONTROL(chan));
 }
 
 #ifdef DWMAC_DMA_DEBUG
@@ -165,7 +165,7 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,
 	struct stmmac_pcpu_stats *stats = this_cpu_ptr(priv->xstats.pcpu_stats);
 	int ret = 0;
 	/* read the status register (CSR5) */
-	u32 intr_status = readl(ioaddr + DMA_STATUS);
+	u32 intr_status = readl(ioaddr + DMA_CHAN_STATUS(chan));
 
 #ifdef DWMAC_DMA_DEBUG
 	/* Enable it to monitor DMA rx/tx status in case of critical problems */
drivers/net/ethernet/stmicro/stmmac/hwif.h +1 -1
index dc6dbb6ce50a..b0bb9cdc335a 100644
@@ -197,7 +197,7 @@ struct stmmac_dma_ops {
 	/* To track extra statistic (if supported) */
 	void (*dma_diagnostic_fr)(struct stmmac_extra_stats *x,
 				  void __iomem *ioaddr);
-	void (*enable_dma_transmission) (void __iomem *ioaddr);
+	void (*enable_dma_transmission)(void __iomem *ioaddr, u32 chan);
 	void (*enable_dma_irq)(struct stmmac_priv *priv, void __iomem *ioaddr,
 			       u32 chan, bool rx, bool tx);
 	void (*disable_dma_irq)(struct stmmac_priv *priv, void __iomem *ioaddr,
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +8 -6
index 5aa0c776757d..ff62c3b7f03d 100644
@@ -2367,9 +2367,11 @@ static void stmmac_dma_operation_mode(struct stmmac_priv *priv)
 	if (txfifosz == 0)
 		txfifosz = priv->dma_cap.tx_fifo_size;
 
-	/* Adjust for real per queue fifo size */
-	rxfifosz /= rx_channels_count;
-	txfifosz /= tx_channels_count;
+	/* Split up the shared Tx/Rx FIFO memory on DW QoS Eth and DW XGMAC */
+	if (priv->plat->has_gmac4 || priv->plat->has_xgmac) {
+		rxfifosz /= rx_channels_count;
+		txfifosz /= tx_channels_count;
+	}
 
 	if (priv->plat->force_thresh_dma_mode) {
 		txmode = tc;
@@ -2553,7 +2555,7 @@ static bool stmmac_xdp_xmit_zc(struct stmmac_priv *priv, u32 queue, u32 budget)
 				       true, priv->mode, true, true,
 				       xdp_desc.len);
 
-		stmmac_enable_dma_transmission(priv, priv->ioaddr);
+		stmmac_enable_dma_transmission(priv, priv->ioaddr, queue);
 
 		xsk_tx_metadata_to_compl(meta,
 					 &tx_q->tx_skbuff_dma[entry].xsk_meta);
@@ -4753,7 +4755,7 @@ static netdev_tx_t stmmac_xmit(struct sk_buff *skb, struct net_device *dev)
 
 	netdev_tx_sent_queue(netdev_get_tx_queue(dev, queue), skb->len);
 
-	stmmac_enable_dma_transmission(priv, priv->ioaddr);
+	stmmac_enable_dma_transmission(priv, priv->ioaddr, queue);
 
 	stmmac_flush_tx_descriptors(priv, queue);
 	stmmac_tx_timer_arm(priv, queue);
@@ -4980,7 +4982,7 @@ static int stmmac_xdp_xmit_xdpf(struct stmmac_priv *priv, int queue,
 		u64_stats_update_end(&txq_stats->q_syncp);
 	}
 
-	stmmac_enable_dma_transmission(priv, priv->ioaddr);
+	stmmac_enable_dma_transmission(priv, priv->ioaddr, queue);
 
 	entry = STMMAC_GET_ENTRY(entry, priv->dma_conf.dma_tx_size);
 	tx_q->cur_tx = entry;
Signature · 1 line
2.31.4
Reviewed-by on v14 2/14
#3 lore raw

Re: [PATCH net-next v14 02/14] net: stmmac: Add multi-channel support

Quoted 11 lines · Yanteng Si

DW GMAC v3.73 can be equipped with the Audio Video (AV) feature which enables transmission of time-sensitive traffic over bridged local area networks (DWC Ethernet QoS Product). In that case there can be up to two additional DMA-channels available with no Tx COE support (unless there is vendor-specific IP-core alterations). Each channel is implemented as a separate Control and Status register (CSR) for managing the transmit and receive functions, descriptor handling, and interrupt handling.

Add the multi-channels DW GMAC controllers support just by making sure the already implemented DMA-configs are performed on the per-channel basis.

Quoted 8 lines

Note the only currently known instance of the multi-channel DW GMAC IP-core is the LS2K2000 GNET controller, which has been released with the vendor-specific feature extension of having eight DMA-channels. The device support will be added in one of the following up commits.

Looking good now. Thanks.

-Serge(y)

Quoted 330 lines
---
 .../net/ethernet/stmicro/stmmac/dwmac-sun8i.c |  2 +-
 .../ethernet/stmicro/stmmac/dwmac1000_dma.c   | 32 ++++++++++---------
 .../net/ethernet/stmicro/stmmac/dwmac_dma.h   | 27 +++++++++++++++-
 .../net/ethernet/stmicro/stmmac/dwmac_lib.c   | 30 ++++++++---------
 drivers/net/ethernet/stmicro/stmmac/hwif.h    |  2 +-
 .../net/ethernet/stmicro/stmmac/stmmac_main.c | 14 ++++----
 6 files changed, 68 insertions(+), 39 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +1 -1
index d87079016952..cc93f73a380e 100644
@@ -395,7 +395,7 @@ static void sun8i_dwmac_dma_start_tx(struct stmmac_priv *priv,
 	writel(v, ioaddr + EMAC_TX_CTL1);
 }
 
-static void sun8i_dwmac_enable_dma_transmission(void __iomem *ioaddr)
+static void sun8i_dwmac_enable_dma_transmission(void __iomem *ioaddr, u32 chan)
 {
 	u32 v;
 
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +17 -15
index 984b809105af..b3d7eff53b18 100644
@@ -70,15 +70,17 @@ static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi)
 	writel(value, ioaddr + DMA_AXI_BUS_MODE);
 }
 
-static void dwmac1000_dma_init(void __iomem *ioaddr,
-			       struct stmmac_dma_cfg *dma_cfg)
+static void dwmac1000_dma_init_channel(struct stmmac_priv *priv,
+				       void __iomem *ioaddr,
+				       struct stmmac_dma_cfg *dma_cfg, u32 chan)
 {
-	u32 value = readl(ioaddr + DMA_BUS_MODE);
 	int txpbl = dma_cfg->txpbl ?: dma_cfg->pbl;
 	int rxpbl = dma_cfg->rxpbl ?: dma_cfg->pbl;
+	u32 value;
 
-	/*
-	 * Set the DMA PBL (Programmable Burst Length) mode.
+	value = readl(ioaddr + DMA_CHAN_BUS_MODE(chan));
+
+	/* Set the DMA PBL (Programmable Burst Length) mode.
 	 *
 	 * Note: before stmmac core 3.50 this mode bit was 4xPBL, and
 	 * post 3.5 mode bit acts as 8*PBL.
@@ -104,10 +106,10 @@ static void dwmac1000_dma_init(void __iomem *ioaddr,
 	if (dma_cfg->aal)
 		value |= DMA_BUS_MODE_AAL;
 
-	writel(value, ioaddr + DMA_BUS_MODE);
+	writel(value, ioaddr + DMA_CHAN_BUS_MODE(chan));
 
 	/* Mask interrupts by writing to CSR7 */
-	writel(DMA_INTR_DEFAULT_MASK, ioaddr + DMA_INTR_ENA);
+	writel(DMA_INTR_DEFAULT_MASK, ioaddr + DMA_CHAN_INTR_ENA(chan));
 }
 
 static void dwmac1000_dma_init_rx(struct stmmac_priv *priv,
@@ -116,7 +118,7 @@ static void dwmac1000_dma_init_rx(struct stmmac_priv *priv,
 				  dma_addr_t dma_rx_phy, u32 chan)
 {
 	/* RX descriptor base address list must be written into DMA CSR3 */
-	writel(lower_32_bits(dma_rx_phy), ioaddr + DMA_RCV_BASE_ADDR);
+	writel(lower_32_bits(dma_rx_phy), ioaddr + DMA_CHAN_RCV_BASE_ADDR(chan));
 }
 
 static void dwmac1000_dma_init_tx(struct stmmac_priv *priv,
@@ -125,7 +127,7 @@ static void dwmac1000_dma_init_tx(struct stmmac_priv *priv,
 				  dma_addr_t dma_tx_phy, u32 chan)
 {
 	/* TX descriptor base address list must be written into DMA CSR4 */
-	writel(lower_32_bits(dma_tx_phy), ioaddr + DMA_TX_BASE_ADDR);
+	writel(lower_32_bits(dma_tx_phy), ioaddr + DMA_CHAN_TX_BASE_ADDR(chan));
 }
 
 static u32 dwmac1000_configure_fc(u32 csr6, int rxfifosz)
@@ -153,7 +155,7 @@ static void dwmac1000_dma_operation_mode_rx(struct stmmac_priv *priv,
 					    void __iomem *ioaddr, int mode,
 					    u32 channel, int fifosz, u8 qmode)
 {
-	u32 csr6 = readl(ioaddr + DMA_CONTROL);
+	u32 csr6 = readl(ioaddr + DMA_CHAN_CONTROL(channel));
 
 	if (mode == SF_DMA_MODE) {
 		pr_debug("GMAC: enable RX store and forward mode\n");
@@ -175,14 +177,14 @@ static void dwmac1000_dma_operation_mode_rx(struct stmmac_priv *priv,
 	/* Configure flow control based on rx fifo size */
 	csr6 = dwmac1000_configure_fc(csr6, fifosz);
 
-	writel(csr6, ioaddr + DMA_CONTROL);
+	writel(csr6, ioaddr + DMA_CHAN_CONTROL(channel));
 }
 
 static void dwmac1000_dma_operation_mode_tx(struct stmmac_priv *priv,
 					    void __iomem *ioaddr, int mode,
 					    u32 channel, int fifosz, u8 qmode)
 {
-	u32 csr6 = readl(ioaddr + DMA_CONTROL);
+	u32 csr6 = readl(ioaddr + DMA_CHAN_CONTROL(channel));
 
 	if (mode == SF_DMA_MODE) {
 		pr_debug("GMAC: enable TX store and forward mode\n");
@@ -209,7 +211,7 @@ static void dwmac1000_dma_operation_mode_tx(struct stmmac_priv *priv,
 			csr6 |= DMA_CONTROL_TTC_256;
 	}
 
-	writel(csr6, ioaddr + DMA_CONTROL);
+	writel(csr6, ioaddr + DMA_CHAN_CONTROL(channel));
 }
 
 static void dwmac1000_dump_dma_regs(struct stmmac_priv *priv,
@@ -271,12 +273,12 @@ static int dwmac1000_get_hw_feature(void __iomem *ioaddr,
 static void dwmac1000_rx_watchdog(struct stmmac_priv *priv,
 				  void __iomem *ioaddr, u32 riwt, u32 queue)
 {
-	writel(riwt, ioaddr + DMA_RX_WATCHDOG);
+	writel(riwt, ioaddr + DMA_CHAN_RX_WATCHDOG(queue));
 }
 
 const struct stmmac_dma_ops dwmac1000_dma_ops = {
 	.reset = dwmac_dma_reset,
-	.init = dwmac1000_dma_init,
+	.init_chan = dwmac1000_dma_init_channel,
 	.init_rx_chan = dwmac1000_dma_init_rx,
 	.init_tx_chan = dwmac1000_dma_init_tx,
 	.axi = dwmac1000_dma_axi,
drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +26 -1
index 72672391675f..5d9c18f5bbf5 100644
@@ -22,6 +22,31 @@
 #define DMA_INTR_ENA		0x0000101c	/* Interrupt Enable */
 #define DMA_MISSED_FRAME_CTR	0x00001020	/* Missed Frame Counter */
 
+/* Following DMA defines are channels oriented */
+#define DMA_CHAN_BASE_OFFSET			0x100
+
+static inline u32 dma_chan_base_addr(u32 base, u32 chan)
+{
+	return base + chan * DMA_CHAN_BASE_OFFSET;
+}
+
+#define DMA_CHAN_BUS_MODE(chan)	dma_chan_base_addr(DMA_BUS_MODE, chan)
+#define DMA_CHAN_XMT_POLL_DEMAND(chan)	\
+				dma_chan_base_addr(DMA_XMT_POLL_DEMAND, chan)
+#define DMA_CHAN_RCV_POLL_DEMAND(chan)	\
+				dma_chan_base_addr(DMA_RCV_POLL_DEMAND, chan)
+#define DMA_CHAN_RCV_BASE_ADDR(chan)	\
+				dma_chan_base_addr(DMA_RCV_BASE_ADDR, chan)
+#define DMA_CHAN_TX_BASE_ADDR(chan)	\
+				dma_chan_base_addr(DMA_TX_BASE_ADDR, chan)
+#define DMA_CHAN_STATUS(chan)	dma_chan_base_addr(DMA_STATUS, chan)
+#define DMA_CHAN_CONTROL(chan)	dma_chan_base_addr(DMA_CONTROL, chan)
+#define DMA_CHAN_INTR_ENA(chan)	dma_chan_base_addr(DMA_INTR_ENA, chan)
+#define DMA_CHAN_MISSED_FRAME_CTR(chan)	\
+				dma_chan_base_addr(DMA_MISSED_FRAME_CTR, chan)
+#define DMA_CHAN_RX_WATCHDOG(chan)	\
+				dma_chan_base_addr(DMA_RX_WATCHDOG, chan)
+
 /* SW Reset */
 #define DMA_BUS_MODE_SFT_RESET	0x00000001	/* Software Reset */
 
@@ -152,7 +177,7 @@
 #define NUM_DWMAC1000_DMA_REGS	23
 #define NUM_DWMAC4_DMA_REGS	27
 
-void dwmac_enable_dma_transmission(void __iomem *ioaddr);
+void dwmac_enable_dma_transmission(void __iomem *ioaddr, u32 chan);
 void dwmac_enable_dma_irq(struct stmmac_priv *priv, void __iomem *ioaddr,
 			  u32 chan, bool rx, bool tx);
 void dwmac_disable_dma_irq(struct stmmac_priv *priv, void __iomem *ioaddr,
drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c +15 -15
index 85e18f9a22f9..4846bf49c576 100644
@@ -28,65 +28,65 @@ int dwmac_dma_reset(void __iomem *ioaddr)
 }
 
 /* CSR1 enables the transmit DMA to check for new descriptor */
-void dwmac_enable_dma_transmission(void __iomem *ioaddr)
+void dwmac_enable_dma_transmission(void __iomem *ioaddr, u32 chan)
 {
-	writel(1, ioaddr + DMA_XMT_POLL_DEMAND);
+	writel(1, ioaddr + DMA_CHAN_XMT_POLL_DEMAND(chan));
 }
 
 void dwmac_enable_dma_irq(struct stmmac_priv *priv, void __iomem *ioaddr,
 			  u32 chan, bool rx, bool tx)
 {
-	u32 value = readl(ioaddr + DMA_INTR_ENA);
+	u32 value = readl(ioaddr + DMA_CHAN_INTR_ENA(chan));
 
 	if (rx)
 		value |= DMA_INTR_DEFAULT_RX;
 	if (tx)
 		value |= DMA_INTR_DEFAULT_TX;
 
-	writel(value, ioaddr + DMA_INTR_ENA);
+	writel(value, ioaddr + DMA_CHAN_INTR_ENA(chan));
 }
 
 void dwmac_disable_dma_irq(struct stmmac_priv *priv, void __iomem *ioaddr,
 			   u32 chan, bool rx, bool tx)
 {
-	u32 value = readl(ioaddr + DMA_INTR_ENA);
+	u32 value = readl(ioaddr + DMA_CHAN_INTR_ENA(chan));
 
 	if (rx)
 		value &= ~DMA_INTR_DEFAULT_RX;
 	if (tx)
 		value &= ~DMA_INTR_DEFAULT_TX;
 
-	writel(value, ioaddr + DMA_INTR_ENA);
+	writel(value, ioaddr + DMA_CHAN_INTR_ENA(chan));
 }
 
 void dwmac_dma_start_tx(struct stmmac_priv *priv, void __iomem *ioaddr,
 			u32 chan)
 {
-	u32 value = readl(ioaddr + DMA_CONTROL);
+	u32 value = readl(ioaddr + DMA_CHAN_CONTROL(chan));
 	value |= DMA_CONTROL_ST;
-	writel(value, ioaddr + DMA_CONTROL);
+	writel(value, ioaddr + DMA_CHAN_CONTROL(chan));
 }
 
 void dwmac_dma_stop_tx(struct stmmac_priv *priv, void __iomem *ioaddr, u32 chan)
 {
-	u32 value = readl(ioaddr + DMA_CONTROL);
+	u32 value = readl(ioaddr + DMA_CHAN_CONTROL(chan));
 	value &= ~DMA_CONTROL_ST;
-	writel(value, ioaddr + DMA_CONTROL);
+	writel(value, ioaddr + DMA_CHAN_CONTROL(chan));
 }
 
 void dwmac_dma_start_rx(struct stmmac_priv *priv, void __iomem *ioaddr,
 			u32 chan)
 {
-	u32 value = readl(ioaddr + DMA_CONTROL);
+	u32 value = readl(ioaddr + DMA_CHAN_CONTROL(chan));
 	value |= DMA_CONTROL_SR;
-	writel(value, ioaddr + DMA_CONTROL);
+	writel(value, ioaddr + DMA_CHAN_CONTROL(chan));
 }
 
 void dwmac_dma_stop_rx(struct stmmac_priv *priv, void __iomem *ioaddr, u32 chan)
 {
-	u32 value = readl(ioaddr + DMA_CONTROL);
+	u32 value = readl(ioaddr + DMA_CHAN_CONTROL(chan));
 	value &= ~DMA_CONTROL_SR;
-	writel(value, ioaddr + DMA_CONTROL);
+	writel(value, ioaddr + DMA_CHAN_CONTROL(chan));
 }
 
 #ifdef DWMAC_DMA_DEBUG
@@ -165,7 +165,7 @@ int dwmac_dma_interrupt(struct stmmac_priv *priv, void __iomem *ioaddr,
 	struct stmmac_pcpu_stats *stats = this_cpu_ptr(priv->xstats.pcpu_stats);
 	int ret = 0;
 	/* read the status register (CSR5) */
-	u32 intr_status = readl(ioaddr + DMA_STATUS);
+	u32 intr_status = readl(ioaddr + DMA_CHAN_STATUS(chan));
 
 #ifdef DWMAC_DMA_DEBUG
 	/* Enable it to monitor DMA rx/tx status in case of critical problems */
drivers/net/ethernet/stmicro/stmmac/hwif.h +1 -1
index dc6dbb6ce50a..b0bb9cdc335a 100644
@@ -197,7 +197,7 @@ struct stmmac_dma_ops {
 	/* To track extra statistic (if supported) */
 	void (*dma_diagnostic_fr)(struct stmmac_extra_stats *x,
 				  void __iomem *ioaddr);
-	void (*enable_dma_transmission) (void __iomem *ioaddr);
+	void (*enable_dma_transmission)(void __iomem *ioaddr, u32 chan);
 	void (*enable_dma_irq)(struct stmmac_priv *priv, void __iomem *ioaddr,
 			       u32 chan, bool rx, bool tx);
 	void (*disable_dma_irq)(struct stmmac_priv *priv, void __iomem *ioaddr,
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +8 -6
index 5aa0c776757d..ff62c3b7f03d 100644
@@ -2367,9 +2367,11 @@ static void stmmac_dma_operation_mode(struct stmmac_priv *priv)
 	if (txfifosz == 0)
 		txfifosz = priv->dma_cap.tx_fifo_size;
 
-	/* Adjust for real per queue fifo size */
-	rxfifosz /= rx_channels_count;
-	txfifosz /= tx_channels_count;
+	/* Split up the shared Tx/Rx FIFO memory on DW QoS Eth and DW XGMAC */
+	if (priv->plat->has_gmac4 || priv->plat->has_xgmac) {
+		rxfifosz /= rx_channels_count;
+		txfifosz /= tx_channels_count;
+	}
 
 	if (priv->plat->force_thresh_dma_mode) {
 		txmode = tc;
@@ -2553,7 +2555,7 @@ static bool stmmac_xdp_xmit_zc(struct stmmac_priv *priv, u32 queue, u32 budget)
 				       true, priv->mode, true, true,
 				       xdp_desc.len);
 
-		stmmac_enable_dma_transmission(priv, priv->ioaddr);
+		stmmac_enable_dma_transmission(priv, priv->ioaddr, queue);
 
 		xsk_tx_metadata_to_compl(meta,
 					 &tx_q->tx_skbuff_dma[entry].xsk_meta);
@@ -4753,7 +4755,7 @@ static netdev_tx_t stmmac_xmit(struct sk_buff *skb, struct net_device *dev)
 
 	netdev_tx_sent_queue(netdev_get_tx_queue(dev, queue), skb->len);
 
-	stmmac_enable_dma_transmission(priv, priv->ioaddr);
+	stmmac_enable_dma_transmission(priv, priv->ioaddr, queue);
 
 	stmmac_flush_tx_descriptors(priv, queue);
 	stmmac_tx_timer_arm(priv, queue);
@@ -4980,7 +4982,7 @@ static int stmmac_xdp_xmit_xdpf(struct stmmac_priv *priv, int queue,
 		u64_stats_update_end(&txq_stats->q_syncp);
 	}
 
-	stmmac_enable_dma_transmission(priv, priv->ioaddr);
+	stmmac_enable_dma_transmission(priv, priv->ioaddr, queue);
 
 	entry = STMMAC_GET_ENTRY(entry, priv->dma_conf.dma_tx_size);
 	tx_q->cur_tx = entry;
Signature · 1 line
2.31.4
author
#4 lore raw

PATCH v14 3/14 net: stmmac: Export dwmac1000_dma_ops

In reply to Yanteng Si

Export the DW GMAC DMA-ops descriptor so one could be available in the low-level platform drivers. It will be utilized to override some callbacks in order to handle the LS2K2000 GNET device specifics. The GNET controller support is being added in one of the following up commits.

---
 drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c | 1 +
 1 file changed, 1 insertion(+)
drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +1 -0
index b3d7eff53b18..118a22406a2e 100644
@@ -296,3 +296,4 @@ const struct stmmac_dma_ops dwmac1000_dma_ops = {
 	.get_hw_feature = dwmac1000_get_hw_feature,
 	.rx_watchdog = dwmac1000_rx_watchdog,
 };
+EXPORT_SYMBOL_GPL(dwmac1000_dma_ops);
Signature · 1 line
2.31.4
author
#5 lore raw

PATCH v14 4/14 net: stmmac: dwmac-loongson: Drop duplicated hash-based filter size init

In reply to Yanteng Si

The plat_stmmacenet_data::multicast_filter_bins field is twice initialized in the loongson_default_data() method. Drop the redundant initialization, but for the readability sake keep the filters init statements defined in the same place of the method.

---
 drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +1 -2
index 9e40c28d453a..9dbd11766364 100644
@@ -16,7 +16,7 @@ static int loongson_default_data(struct plat_stmmacenet_data *plat)
 	plat->force_sf_dma_mode = 1;
 
 	/* Set default value for multicast hash bins */
-	plat->multicast_filter_bins = HASH_TABLE_SIZE;
+	plat->multicast_filter_bins = 256;
 
 	/* Set default value for unicast filter entries */
 	plat->unicast_filter_entries = 1;
@@ -41,7 +41,6 @@ static int loongson_default_data(struct plat_stmmacenet_data *plat)
 	plat->dma_cfg->pbl = 32;
 	plat->dma_cfg->pblx8 = true;
 
-	plat->multicast_filter_bins = 256;
 	return 0;
 }
 
Signature · 1 line
2.31.4
author
#6 lore raw

PATCH v14 5/14 net: stmmac: dwmac-loongson: Drop pci_enable/disable_msi calls

In reply to Yanteng Si

The Loongson GMAC driver currently doesn't utilize the MSI IRQs, but retrieves the IRQs specified in the device DT-node. Let's drop the direct pci_enable_msi()/pci_disable_msi() calls then as redundant

---
 drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c | 10 +++-------
 1 file changed, 3 insertions(+), 7 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +3 -7
index 9dbd11766364..32814afdf321 100644
@@ -114,7 +114,6 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
 	pci_set_master(pdev);
 
 	loongson_default_data(plat);
-	pci_enable_msi(pdev);
 	memset(&res, 0, sizeof(res));
 	res.addr = pcim_iomap_table(pdev)[0];
 
@@ -122,7 +121,7 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
 	if (res.irq < 0) {
 		dev_err(&pdev->dev, "IRQ macirq not found\n");
 		ret = -ENODEV;
-		goto err_disable_msi;
+		goto err_disable_device;
 	}
 
 	res.wol_irq = of_irq_get_byname(np, "eth_wake_irq");
@@ -135,17 +134,15 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
 	if (res.lpi_irq < 0) {
 		dev_err(&pdev->dev, "IRQ eth_lpi not found\n");
 		ret = -ENODEV;
-		goto err_disable_msi;
+		goto err_disable_device;
 	}
 
 	ret = stmmac_dvr_probe(&pdev->dev, plat, &res);
 	if (ret)
-		goto err_disable_msi;
+		goto err_disable_device;
 
 	return ret;
 
-err_disable_msi:
-	pci_disable_msi(pdev);
 err_disable_device:
 	pci_disable_device(pdev);
 err_put_node:
@@ -169,7 +166,6 @@ static void loongson_dwmac_remove(struct pci_dev *pdev)
 		break;
 	}
 
-	pci_disable_msi(pdev);
 	pci_disable_device(pdev);
 }
 
Signature · 1 line
2.31.4
Reviewed-by on v14 5/14
#7 lore raw

Re: [PATCH net-next v14 05/14] net: stmmac: dwmac-loongson: Drop pci_enable/disable_msi calls

Quoted 7 lines · Yanteng Si

The Loongson GMAC driver currently doesn't utilize the MSI IRQs, but retrieves the IRQs specified in the device DT-node. Let's drop the direct pci_enable_msi()/pci_disable_msi() calls then as redundant

-Serge(y)

Quoted 56 lines
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c | 10 +++-------
 1 file changed, 3 insertions(+), 7 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +3 -7
index 9dbd11766364..32814afdf321 100644
@@ -114,7 +114,6 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
 	pci_set_master(pdev);
 
 	loongson_default_data(plat);
-	pci_enable_msi(pdev);
 	memset(&res, 0, sizeof(res));
 	res.addr = pcim_iomap_table(pdev)[0];
 
@@ -122,7 +121,7 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
 	if (res.irq < 0) {
 		dev_err(&pdev->dev, "IRQ macirq not found\n");
 		ret = -ENODEV;
-		goto err_disable_msi;
+		goto err_disable_device;
 	}
 
 	res.wol_irq = of_irq_get_byname(np, "eth_wake_irq");
@@ -135,17 +134,15 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
 	if (res.lpi_irq < 0) {
 		dev_err(&pdev->dev, "IRQ eth_lpi not found\n");
 		ret = -ENODEV;
-		goto err_disable_msi;
+		goto err_disable_device;
 	}
 
 	ret = stmmac_dvr_probe(&pdev->dev, plat, &res);
 	if (ret)
-		goto err_disable_msi;
+		goto err_disable_device;
 
 	return ret;
 
-err_disable_msi:
-	pci_disable_msi(pdev);
 err_disable_device:
 	pci_disable_device(pdev);
 err_put_node:
@@ -169,7 +166,6 @@ static void loongson_dwmac_remove(struct pci_dev *pdev)
 		break;
 	}
 
-	pci_disable_msi(pdev);
 	pci_disable_device(pdev);
 }
 
Signature · 1 line
2.31.4
author
#8 lore raw

PATCH v14 6/14 net: stmmac: dwmac-loongson: Use PCI_DEVICE_DATA() macro for device identification

In reply to Yanteng Si

For the readability sake convert the hard-coded Loongson GMAC PCI ID to the respective macro and use the PCI_DEVICE_DATA() macro-function to create the pci_device_id array entry. The later change will be specifically useful in order to assign the device-specific data for the currently supported device and for about to be added Loongson GNET controller.

---
 drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +3 -1
index 32814afdf321..f39c13a74bb5 100644
@@ -9,6 +9,8 @@
 #include <linux/of_irq.h>
 #include "stmmac.h"
 
+#define PCI_DEVICE_ID_LOONGSON_GMAC	0x7a03
+
 static int loongson_default_data(struct plat_stmmacenet_data *plat)
 {
 	plat->clk_csr = 2;	/* clk_csr_i = 20-35MHz & MDC = clk_csr_i/16 */
@@ -208,7 +210,7 @@ static SIMPLE_DEV_PM_OPS(loongson_dwmac_pm_ops, loongson_dwmac_suspend,
 			 loongson_dwmac_resume);
 
 static const struct pci_device_id loongson_dwmac_id_table[] = {
-	{ PCI_VDEVICE(LOONGSON, 0x7a03) },
+	{ PCI_DEVICE_DATA(LOONGSON, GMAC, NULL) },
 	{}
 };
 MODULE_DEVICE_TABLE(pci, loongson_dwmac_id_table);
Signature · 1 line
2.31.4
author
#9 lore raw

PATCH v14 7/14 net: stmmac: dwmac-loongson: Detach GMAC-specific platform data init

In reply to Yanteng Si

Loongson delivers two types of the network devices: Loongson GMAC and Loongson GNET in the framework of four CPU/Chipsets revisions:

Chip Network PCI Dev ID Synopys Version DMA-channel

LS2K1000 CPU         GMAC      0x7a03       v3.50a/v3.73a        1
LS7A1000 Chipset     GMAC      0x7a03       v3.50a/v3.73a        1
LS2K2000 CPU         GMAC      0x7a03          v3.73a            8
LS2K2000 CPU         GNET      0x7a13          v3.73a            8
LS7A2000 Chipset     GNET      0x7a13          v3.73a            1

The driver currently supports the chips with the Loongson GMAC network device synthesized with a single DMA-channel available. As a preparation before adding the Loongson GNET support detach the Loongson GMAC-specific platform data initializations to the loongson_gmac_data() method and preserve the common settings in the loongson_default_data().

While at it drop the return value statement from the loongson_default_data() method as redundant.

---
 .../ethernet/stmicro/stmmac/dwmac-loongson.c  | 19 ++++++++++++-------
 1 file changed, 12 insertions(+), 7 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +12 -7
index f39c13a74bb5..9b2e4bdf7cc7 100644
@@ -11,7 +11,7 @@
 
 #define PCI_DEVICE_ID_LOONGSON_GMAC	0x7a03
 
-static int loongson_default_data(struct plat_stmmacenet_data *plat)
+static void loongson_default_data(struct plat_stmmacenet_data *plat)
 {
 	plat->clk_csr = 2;	/* clk_csr_i = 20-35MHz & MDC = clk_csr_i/16 */
 	plat->has_gmac = 1;
@@ -20,16 +20,14 @@ static int loongson_default_data(struct plat_stmmacenet_data *plat)
 	/* Set default value for multicast hash bins */
 	plat->multicast_filter_bins = 256;
 
+	plat->mac_interface = PHY_INTERFACE_MODE_NA;
+
 	/* Set default value for unicast filter entries */
 	plat->unicast_filter_entries = 1;
 
 	/* Set the maxmtu to a default of JUMBO_LEN */
 	plat->maxmtu = JUMBO_LEN;
 
-	/* Set default number of RX and TX queues to use */
-	plat->tx_queues_to_use = 1;
-	plat->rx_queues_to_use = 1;
-
 	/* Disable Priority config by default */
 	plat->tx_queues_cfg[0].use_prio = false;
 	plat->rx_queues_cfg[0].use_prio = false;
@@ -42,6 +40,14 @@ static int loongson_default_data(struct plat_stmmacenet_data *plat)
 
 	plat->dma_cfg->pbl = 32;
 	plat->dma_cfg->pblx8 = true;
+}
+
+static int loongson_gmac_data(struct plat_stmmacenet_data *plat)
+{
+	loongson_default_data(plat);
+
+	plat->tx_queues_to_use = 1;
+	plat->rx_queues_to_use = 1;
 
 	return 0;
 }
@@ -111,11 +117,10 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
 	}
 
 	plat->phy_interface = phy_mode;
-	plat->mac_interface = PHY_INTERFACE_MODE_GMII;
 
 	pci_set_master(pdev);
 
-	loongson_default_data(plat);
+	loongson_gmac_data(plat);
 	memset(&res, 0, sizeof(res));
 	res.addr = pcim_iomap_table(pdev)[0];
 
Signature · 1 line
2.31.4
Reviewed-by on v14 7/14
#10 lore raw

Re: [PATCH net-next v14 07/14] net: stmmac: dwmac-loongson: Detach GMAC-specific platform data init

Quoted 17 lines · Yanteng Si

Loongson delivers two types of the network devices: Loongson GMAC and Loongson GNET in the framework of four CPU/Chipsets revisions:

Chip Network PCI Dev ID Synopys Version DMA-channel

LS2K1000 CPU         GMAC      0x7a03       v3.50a/v3.73a        1
LS7A1000 Chipset     GMAC      0x7a03       v3.50a/v3.73a        1
LS2K2000 CPU         GMAC      0x7a03          v3.73a            8
LS2K2000 CPU         GNET      0x7a13          v3.73a            8
LS7A2000 Chipset     GNET      0x7a13          v3.73a            1

The driver currently supports the chips with the Loongson GMAC network device synthesized with a single DMA-channel available. As a preparation before adding the Loongson GNET support detach the Loongson GMAC-specific platform data initializations to the loongson_gmac_data() method and preserve the common settings in the loongson_default_data().

Quoted 2 lines

While at it drop the return value statement from the loongson_default_data() method as redundant.

Please add a word about the plat->mac_interface field value changed to NA. Something like this:

"Note there is no intermediate vendor-specific PCS in between the MAC and PHY on Loongson GMAC and GNET. So the plat->mac_interface field can be freely initialized with the PHY_INTERFACE_MODE_NA value."

Other than that the change looks good. Thanks.

-Serge(y)

Quoted 71 lines
---
 .../ethernet/stmicro/stmmac/dwmac-loongson.c  | 19 ++++++++++++-------
 1 file changed, 12 insertions(+), 7 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +12 -7
index f39c13a74bb5..9b2e4bdf7cc7 100644
@@ -11,7 +11,7 @@
 
 #define PCI_DEVICE_ID_LOONGSON_GMAC	0x7a03
 
-static int loongson_default_data(struct plat_stmmacenet_data *plat)
+static void loongson_default_data(struct plat_stmmacenet_data *plat)
 {
 	plat->clk_csr = 2;	/* clk_csr_i = 20-35MHz & MDC = clk_csr_i/16 */
 	plat->has_gmac = 1;
@@ -20,16 +20,14 @@ static int loongson_default_data(struct plat_stmmacenet_data *plat)
 	/* Set default value for multicast hash bins */
 	plat->multicast_filter_bins = 256;
 
+	plat->mac_interface = PHY_INTERFACE_MODE_NA;
+
 	/* Set default value for unicast filter entries */
 	plat->unicast_filter_entries = 1;
 
 	/* Set the maxmtu to a default of JUMBO_LEN */
 	plat->maxmtu = JUMBO_LEN;
 
-	/* Set default number of RX and TX queues to use */
-	plat->tx_queues_to_use = 1;
-	plat->rx_queues_to_use = 1;
-
 	/* Disable Priority config by default */
 	plat->tx_queues_cfg[0].use_prio = false;
 	plat->rx_queues_cfg[0].use_prio = false;
@@ -42,6 +40,14 @@ static int loongson_default_data(struct plat_stmmacenet_data *plat)
 
 	plat->dma_cfg->pbl = 32;
 	plat->dma_cfg->pblx8 = true;
+}
+
+static int loongson_gmac_data(struct plat_stmmacenet_data *plat)
+{
+	loongson_default_data(plat);
+
+	plat->tx_queues_to_use = 1;
+	plat->rx_queues_to_use = 1;
 
 	return 0;
 }
@@ -111,11 +117,10 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
 	}
 
 	plat->phy_interface = phy_mode;
-	plat->mac_interface = PHY_INTERFACE_MODE_GMII;
 
 	pci_set_master(pdev);
 
-	loongson_default_data(plat);
+	loongson_gmac_data(plat);
 	memset(&res, 0, sizeof(res));
 	res.addr = pcim_iomap_table(pdev)[0];
 
Signature · 1 line
2.31.4
author
#11 lore raw

PATCH v14 8/14 net: stmmac: dwmac-loongson: Init ref and PTP clocks rate

In reply to Yanteng Si

Reference and PTP clocks rate of the Loongson GMAC devices is 125MHz. (So is in the GNET devices which support is about to be added.) Set the respective plat_stmmacenet_data field up in accordance with that so to have the coalesce command and timestamping work correctly.

---
 drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +3 -0
index 9b2e4bdf7cc7..327275b28dc2 100644
@@ -35,6 +35,9 @@ static void loongson_default_data(struct plat_stmmacenet_data *plat)
 	/* Disable RX queues routing by default */
 	plat->rx_queues_cfg[0].pkt_route = 0x0;
 
+	plat->clk_ref_rate = 125000000;
+	plat->clk_ptp_rate = 125000000;
+
 	/* Default to phy auto-detection */
 	plat->phy_addr = -1;
 
Signature · 1 line
2.31.4
Reviewed-by on v14 8/14
#12 lore raw

Re: [PATCH net-next v14 08/14] net: stmmac: dwmac-loongson: Init ref and PTP clocks rate

Quoted 8 lines · Yanteng Si

Reference and PTP clocks rate of the Loongson GMAC devices is 125MHz. (So is in the GNET devices which support is about to be added.) Set the respective plat_stmmacenet_data field up in accordance with that so to have the coalesce command and timestamping work correctly.

Note the maintainers may wish to get a clarification whether the patch should be qualified as a fix and backported to the stable kernels. In the later case the Fixes tag should be added with the commit hash causing the problem.

Anyway. From my perspective the patch looks good. Thanks.

-Serge(y)

Quoted 21 lines
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +3 -0
index 9b2e4bdf7cc7..327275b28dc2 100644
@@ -35,6 +35,9 @@ static void loongson_default_data(struct plat_stmmacenet_data *plat)
 	/* Disable RX queues routing by default */
 	plat->rx_queues_cfg[0].pkt_route = 0x0;
 
+	plat->clk_ref_rate = 125000000;
+	plat->clk_ptp_rate = 125000000;
+
 	/* Default to phy auto-detection */
 	plat->phy_addr = -1;
 
Signature · 1 line
2.31.4
author
#13 lore raw

PATCH v14 9/14 net: stmmac: dwmac-loongson: Add phy_interface for Loongson GMAC

In reply to Yanteng Si

PHY-interface of the Loongson GMAC device is RGMII with no internal delays added to the data lines signal. So to comply with that let's pre-initialize the platform-data field with the respective enum constant.

---
 drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +2 -0
index 327275b28dc2..7d3f284b9176 100644
@@ -52,6 +52,8 @@ static int loongson_gmac_data(struct plat_stmmacenet_data *plat)
 	plat->tx_queues_to_use = 1;
 	plat->rx_queues_to_use = 1;
 
+	plat->phy_interface = PHY_INTERFACE_MODE_RGMII_ID;
+
 	return 0;
 }
 
Signature · 1 line
2.31.4
Reviewed-by on v14 9/14
#14 lore raw

Re: [PATCH net-next v14 09/14] net: stmmac: dwmac-loongson: Add phy_interface for Loongson GMAC

Quoted 8 lines · Yanteng Si

PHY-interface of the Loongson GMAC device is RGMII with no internal delays added to the data lines signal. So to comply with that let's pre-initialize the platform-data field with the respective enum constant.

-Serge(y)

Quoted 20 lines
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +2 -0
index 327275b28dc2..7d3f284b9176 100644
@@ -52,6 +52,8 @@ static int loongson_gmac_data(struct plat_stmmacenet_data *plat)
 	plat->tx_queues_to_use = 1;
 	plat->rx_queues_to_use = 1;
 
+	plat->phy_interface = PHY_INTERFACE_MODE_RGMII_ID;
+
 	return 0;
 }
 
Signature · 1 line
2.31.4
author
#15 lore raw

PATCH v14 10/14 net: stmmac: dwmac-loongson: Introduce PCI device info data

In reply to Yanteng Si

The Loongson GNET device support is about to be added in one of the next commits. As another preparation for that introduce the PCI device info data with a setup() callback performing the device-specific platform data initializations. Currently it is utilized for the already supported Loongson GMAC device only.

---
 .../ethernet/stmicro/stmmac/dwmac-loongson.c    | 17 +++++++++++++++--
 1 file changed, 15 insertions(+), 2 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +15 -2
index 7d3f284b9176..10b49bea8e3c 100644
@@ -11,6 +11,10 @@
 
 #define PCI_DEVICE_ID_LOONGSON_GMAC	0x7a03
 
+struct stmmac_pci_info {
+	int (*setup)(struct plat_stmmacenet_data *plat);
+};
+
 static void loongson_default_data(struct plat_stmmacenet_data *plat)
 {
 	plat->clk_csr = 2;	/* clk_csr_i = 20-35MHz & MDC = clk_csr_i/16 */
@@ -57,9 +61,14 @@ static int loongson_gmac_data(struct plat_stmmacenet_data *plat)
 	return 0;
 }
 
+static struct stmmac_pci_info loongson_gmac_pci_info = {
+	.setup = loongson_gmac_data,
+};
+
 static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 {
 	struct plat_stmmacenet_data *plat;
+	struct stmmac_pci_info *info;
 	struct stmmac_resources res;
 	struct device_node *np;
 	int ret, i, phy_mode;
@@ -125,10 +134,14 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
 
 	pci_set_master(pdev);
 
-	loongson_gmac_data(plat);
 	memset(&res, 0, sizeof(res));
 	res.addr = pcim_iomap_table(pdev)[0];
 
+	info = (struct stmmac_pci_info *)id->driver_data;
+	ret = info->setup(plat);
+	if (ret)
+		goto err_disable_device;
+
 	res.irq = of_irq_get_byname(np, "macirq");
 	if (res.irq < 0) {
 		dev_err(&pdev->dev, "IRQ macirq not found\n");
@@ -220,7 +233,7 @@ static SIMPLE_DEV_PM_OPS(loongson_dwmac_pm_ops, loongson_dwmac_suspend,
 			 loongson_dwmac_resume);
 
 static const struct pci_device_id loongson_dwmac_id_table[] = {
-	{ PCI_DEVICE_DATA(LOONGSON, GMAC, NULL) },
+	{ PCI_DEVICE_DATA(LOONGSON, GMAC, &loongson_gmac_pci_info) },
 	{}
 };
 MODULE_DEVICE_TABLE(pci, loongson_dwmac_id_table);
Signature · 1 line
2.31.4
Reviewed-by on v14 10/14
#16 lore raw

Re: [PATCH net-next v14 10/14] net: stmmac: dwmac-loongson: Introduce PCI device info data

Quoted 9 lines · Yanteng Si

The Loongson GNET device support is about to be added in one of the next commits. As another preparation for that introduce the PCI device info data with a setup() callback performing the device-specific platform data initializations. Currently it is utilized for the already supported Loongson GMAC device only.

-Serge(y)

Quoted 62 lines
---
 .../ethernet/stmicro/stmmac/dwmac-loongson.c    | 17 +++++++++++++++--
 1 file changed, 15 insertions(+), 2 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +15 -2
index 7d3f284b9176..10b49bea8e3c 100644
@@ -11,6 +11,10 @@
 
 #define PCI_DEVICE_ID_LOONGSON_GMAC	0x7a03
 
+struct stmmac_pci_info {
+	int (*setup)(struct plat_stmmacenet_data *plat);
+};
+
 static void loongson_default_data(struct plat_stmmacenet_data *plat)
 {
 	plat->clk_csr = 2;	/* clk_csr_i = 20-35MHz & MDC = clk_csr_i/16 */
@@ -57,9 +61,14 @@ static int loongson_gmac_data(struct plat_stmmacenet_data *plat)
 	return 0;
 }
 
+static struct stmmac_pci_info loongson_gmac_pci_info = {
+	.setup = loongson_gmac_data,
+};
+
 static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 {
 	struct plat_stmmacenet_data *plat;
+	struct stmmac_pci_info *info;
 	struct stmmac_resources res;
 	struct device_node *np;
 	int ret, i, phy_mode;
@@ -125,10 +134,14 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
 
 	pci_set_master(pdev);
 
-	loongson_gmac_data(plat);
 	memset(&res, 0, sizeof(res));
 	res.addr = pcim_iomap_table(pdev)[0];
 
+	info = (struct stmmac_pci_info *)id->driver_data;
+	ret = info->setup(plat);
+	if (ret)
+		goto err_disable_device;
+
 	res.irq = of_irq_get_byname(np, "macirq");
 	if (res.irq < 0) {
 		dev_err(&pdev->dev, "IRQ macirq not found\n");
@@ -220,7 +233,7 @@ static SIMPLE_DEV_PM_OPS(loongson_dwmac_pm_ops, loongson_dwmac_suspend,
 			 loongson_dwmac_resume);
 
 static const struct pci_device_id loongson_dwmac_id_table[] = {
-	{ PCI_DEVICE_DATA(LOONGSON, GMAC, NULL) },
+	{ PCI_DEVICE_DATA(LOONGSON, GMAC, &loongson_gmac_pci_info) },
 	{}
 };
 MODULE_DEVICE_TABLE(pci, loongson_dwmac_id_table);
Signature · 1 line
2.31.4
author
#17 lore raw

PATCH v14 11/14 net: stmmac: dwmac-loongson: Add DT-less GMAC PCI-device support

In reply to Yanteng Si

The Loongson GMAC driver currently supports the network controllers installed on the LS2K1000 SoC and LS7A1000 chipset, for which the GMAC devices are required to be defined in the platform device tree source. But Loongson machines may have UEFI (implies ACPI) or PMON/UBOOT (implies FDT) as the system bootloaders. In order to have both system configurations support let's extend the driver functionality with the case of having the Loongson GMAC probed on the PCI bus with no device tree node defined for it. That requires to make the device DT-node optional, to rely on the IRQ line detected by the PCI core and to have the MDIO bus ID calculated using the PCIe Domain+BDF numbers.

---
 .../ethernet/stmicro/stmmac/dwmac-loongson.c  | 136 ++++++++++--------
 1 file changed, 79 insertions(+), 57 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +79 -57
index 10b49bea8e3c..b4704068321f 100644
@@ -12,11 +12,15 @@
 #define PCI_DEVICE_ID_LOONGSON_GMAC	0x7a03
 
 struct stmmac_pci_info {
-	int (*setup)(struct plat_stmmacenet_data *plat);
+	int (*setup)(struct pci_dev *pdev, struct plat_stmmacenet_data *plat);
 };
 
-static void loongson_default_data(struct plat_stmmacenet_data *plat)
+static void loongson_default_data(struct pci_dev *pdev,
+				  struct plat_stmmacenet_data *plat)
 {
+	/* Get bus_id, this can be overwritten later */
+	plat->bus_id = pci_dev_id(pdev);
+
 	plat->clk_csr = 2;	/* clk_csr_i = 20-35MHz & MDC = clk_csr_i/16 */
 	plat->has_gmac = 1;
 	plat->force_sf_dma_mode = 1;
@@ -49,9 +53,10 @@ static void loongson_default_data(struct plat_stmmacenet_data *plat)
 	plat->dma_cfg->pblx8 = true;
 }
 
-static int loongson_gmac_data(struct plat_stmmacenet_data *plat)
+static int loongson_gmac_data(struct pci_dev *pdev,
+			      struct plat_stmmacenet_data *plat)
 {
-	loongson_default_data(plat);
+	loongson_default_data(pdev, plat);
 
 	plat->tx_queues_to_use = 1;
 	plat->rx_queues_to_use = 1;
@@ -65,21 +70,72 @@ static struct stmmac_pci_info loongson_gmac_pci_info = {
 	.setup = loongson_gmac_data,
 };
 
-static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id *id)
+static int loongson_dwmac_dt_config(struct pci_dev *pdev,
+				    struct plat_stmmacenet_data *plat,
+				    struct stmmac_resources *res)
 {
-	struct plat_stmmacenet_data *plat;
-	struct stmmac_pci_info *info;
-	struct stmmac_resources res;
-	struct device_node *np;
-	int ret, i, phy_mode;
+	struct device_node *np = dev_of_node(&pdev->dev);
+	int ret;
+
+	plat->mdio_node = of_get_child_by_name(np, "mdio");
+	if (plat->mdio_node) {
+		dev_info(&pdev->dev, "Found MDIO subnode\n");
+		plat->mdio_bus_data->needs_reset = true;
+	}
+
+	ret = of_alias_get_id(np, "ethernet");
+	if (ret >= 0)
+		plat->bus_id = ret;
+
+	res->irq = of_irq_get_byname(np, "macirq");
+	if (res->irq < 0) {
+		dev_err(&pdev->dev, "IRQ macirq not found\n");
+		return -ENODEV;
+	}
 
-	np = dev_of_node(&pdev->dev);
+	res->wol_irq = of_irq_get_byname(np, "eth_wake_irq");
+	if (res->wol_irq < 0) {
+		dev_info(&pdev->dev,
+			 "IRQ eth_wake_irq not found, using macirq\n");
+		res->wol_irq = res->irq;
+	}
 
-	if (!np) {
-		pr_info("dwmac_loongson_pci: No OF node\n");
+	res->lpi_irq = of_irq_get_byname(np, "eth_lpi");
+	if (res->lpi_irq < 0) {
+		dev_err(&pdev->dev, "IRQ eth_lpi not found\n");
 		return -ENODEV;
 	}
 
+	ret = device_get_phy_mode(&pdev->dev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "phy_mode not found\n");
+		return -ENODEV;
+	}
+
+	plat->phy_interface = ret;
+
+	return 0;
+}
+
+static int loongson_dwmac_acpi_config(struct pci_dev *pdev,
+				      struct plat_stmmacenet_data *plat,
+				      struct stmmac_resources *res)
+{
+	if (!pdev->irq)
+		return -EINVAL;
+
+	res->irq = pdev->irq;
+
+	return 0;
+}
+
+static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+	struct plat_stmmacenet_data *plat;
+	struct stmmac_pci_info *info;
+	struct stmmac_resources res;
+	int ret, i;
+
 	plat = devm_kzalloc(&pdev->dev, sizeof(*plat), GFP_KERNEL);
 	if (!plat)
 		return -ENOMEM;
@@ -90,17 +146,9 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
 	if (!plat->mdio_bus_data)
 		return -ENOMEM;
 
-	plat->mdio_node = of_get_child_by_name(np, "mdio");
-	if (plat->mdio_node) {
-		dev_info(&pdev->dev, "Found MDIO subnode\n");
-		plat->mdio_bus_data->needs_reset = true;
-	}
-
 	plat->dma_cfg = devm_kzalloc(&pdev->dev, sizeof(*plat->dma_cfg), GFP_KERNEL);
-	if (!plat->dma_cfg) {
-		ret = -ENOMEM;
-		goto err_put_node;
-	}
+	if (!plat->dma_cfg)
+		return -ENOMEM;
 
 	/* Enable pci device */
 	ret = pci_enable_device(pdev);
@@ -109,6 +157,8 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
 		goto err_put_node;
 	}
 
+	pci_set_master(pdev);
+
 	/* Get the base address of device */
 	for (i = 0; i < PCI_STD_NUM_BARS; i++) {
 		if (pci_resource_len(pdev, i) == 0)
@@ -119,48 +169,20 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
 		break;
 	}
 
-	plat->bus_id = of_alias_get_id(np, "ethernet");
-	if (plat->bus_id < 0)
-		plat->bus_id = pci_dev_id(pdev);
-
-	phy_mode = device_get_phy_mode(&pdev->dev);
-	if (phy_mode < 0) {
-		dev_err(&pdev->dev, "phy_mode not found\n");
-		ret = phy_mode;
-		goto err_disable_device;
-	}
-
-	plat->phy_interface = phy_mode;
-
-	pci_set_master(pdev);
-
 	memset(&res, 0, sizeof(res));
 	res.addr = pcim_iomap_table(pdev)[0];
 
 	info = (struct stmmac_pci_info *)id->driver_data;
-	ret = info->setup(plat);
+	ret = info->setup(pdev, plat);
 	if (ret)
 		goto err_disable_device;
 
-	res.irq = of_irq_get_byname(np, "macirq");
-	if (res.irq < 0) {
-		dev_err(&pdev->dev, "IRQ macirq not found\n");
-		ret = -ENODEV;
-		goto err_disable_device;
-	}
-
-	res.wol_irq = of_irq_get_byname(np, "eth_wake_irq");
-	if (res.wol_irq < 0) {
-		dev_info(&pdev->dev, "IRQ eth_wake_irq not found, using macirq\n");
-		res.wol_irq = res.irq;
-	}
-
-	res.lpi_irq = of_irq_get_byname(np, "eth_lpi");
-	if (res.lpi_irq < 0) {
-		dev_err(&pdev->dev, "IRQ eth_lpi not found\n");
-		ret = -ENODEV;
+	if (dev_of_node(&pdev->dev))
+		ret = loongson_dwmac_dt_config(pdev, plat, &res);
+	else
+		ret = loongson_dwmac_acpi_config(pdev, plat, &res);
+	if (ret)
 		goto err_disable_device;
-	}
 
 	ret = stmmac_dvr_probe(&pdev->dev, plat, &res);
 	if (ret)
Signature · 1 line
2.31.4
#18 lore raw

Re: [PATCH net-next v14 11/14] net: stmmac: dwmac-loongson: Add DT-less GMAC PCI-device support

Quoted 10 lines · Yanteng Si

The Loongson GMAC driver currently supports the network controllers installed on the LS2K1000 SoC and LS7A1000 chipset, for which the GMAC devices are required to be defined in the platform device tree source. But Loongson machines may have UEFI (implies ACPI) or PMON/UBOOT (implies FDT) as the system bootloaders. In order to have both system configurations support let's extend the driver functionality with the case of having the Loongson GMAC probed on the PCI bus with no device tree node defined for it. That requires to make the device DT-node optional, to rely on the IRQ line detected by the PCI core and to have the MDIO bus ID calculated using the PCIe Domain+BDF numbers.

Let's extend the log with an additional note:

"In order to have the device probe() and remove() methods less complicated let's move the DT- and ACPI-specific code to the respective sub-functions."

Quoted 56 lines
---
 .../ethernet/stmicro/stmmac/dwmac-loongson.c  | 136 ++++++++++--------
 1 file changed, 79 insertions(+), 57 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +12 -9
index 10b49bea8e3c..b4704068321f 100644
@@ -12,11 +12,15 @@
 #define PCI_DEVICE_ID_LOONGSON_GMAC	0x7a03
 
 struct stmmac_pci_info {
-	int (*setup)(struct plat_stmmacenet_data *plat);
+	int (*setup)(struct pci_dev *pdev, struct plat_stmmacenet_data *plat);
 };
 
-static void loongson_default_data(struct plat_stmmacenet_data *plat)
+static void loongson_default_data(struct pci_dev *pdev,
+				  struct plat_stmmacenet_data *plat)
 {
+	/* Get bus_id, this can be overwritten later */
+	plat->bus_id = pci_dev_id(pdev);
+
 	plat->clk_csr = 2;	/* clk_csr_i = 20-35MHz & MDC = clk_csr_i/16 */
 	plat->has_gmac = 1;
 	plat->force_sf_dma_mode = 1;
@@ -49,9 +53,10 @@ static void loongson_default_data(struct plat_stmmacenet_data *plat)
 	plat->dma_cfg->pblx8 = true;
 }
 
-static int loongson_gmac_data(struct plat_stmmacenet_data *plat)
+static int loongson_gmac_data(struct pci_dev *pdev,
+			      struct plat_stmmacenet_data *plat)
 {
-	loongson_default_data(plat);
+	loongson_default_data(pdev, plat);
 
 	plat->tx_queues_to_use = 1;
 	plat->rx_queues_to_use = 1;
@@ -65,21 +70,72 @@ static struct stmmac_pci_info loongson_gmac_pci_info = {
 	.setup = loongson_gmac_data,
 };
 
-static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id *id)
+static int loongson_dwmac_dt_config(struct pci_dev *pdev,
+				    struct plat_stmmacenet_data *plat,
+				    struct stmmac_resources *res)
 {
-	struct plat_stmmacenet_data *plat;
-	struct stmmac_pci_info *info;
-	struct stmmac_resources res;
-	struct device_node *np;

drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 85

Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +8 -1
-	int ret, i, phy_mode;
+	struct device_node *np = dev_of_node(&pdev->dev);
+	int ret;
+
 
+	plat->mdio_node = of_get_child_by_name(np, "mdio");
+	if (plat->mdio_node) {
+		dev_info(&pdev->dev, "Found MDIO subnode\n");
+		plat->mdio_bus_data->needs_reset = true;
+	}

This needs to be reverted in case if the following up code fails. So ...

drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 112

Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +9 -0
+
+	ret = of_alias_get_id(np, "ethernet");
+	if (ret >= 0)
+		plat->bus_id = ret;
+
+	res->irq = of_irq_get_byname(np, "macirq");
+	if (res->irq < 0) {
+		dev_err(&pdev->dev, "IRQ macirq not found\n");
 
+		return -ENODEV;
		ret = -ENODEV;
		goto err_put_node;
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +5 -1
+	}
 
-	np = dev_of_node(&pdev->dev);
+	res->wol_irq = of_irq_get_byname(np, "eth_wake_irq");
+	if (res->wol_irq < 0) {
+		dev_info(&pdev->dev,
+			 "IRQ eth_wake_irq not found, using macirq\n");

drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = {

Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +5 -2
+		res->wol_irq = res->irq;
+	}
 
-	if (!np) {
-		pr_info("dwmac_loongson_pci: No OF node\n");
+	res->lpi_irq = of_irq_get_byname(np, "eth_lpi");
+	if (res->lpi_irq < 0) {
+		dev_err(&pdev->dev, "IRQ eth_lpi not found\n");
 
 		return -ENODEV;
		err = -ENODEV;
		goto err_put_node;

drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 112

Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +4 -0
 	}
 
+	ret = device_get_phy_mode(&pdev->dev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "phy_mode not found\n");
 
+		return -ENODEV;
		goto err_put_node;

drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 117

Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +5 -0
+	}
+
+	plat->phy_interface = ret;
+
+	return 0;

err_put_node:

	of_node_put(plat->mdio_node);

	return ret;
Quoted 1 line

+}

static void loongson_dwmac_dt_clear(struct pci_dev *pdev,
struct plat_stmmacenet_data *plat)

{
	of_node_put(plat->mdio_node);
}

and ...

Quoted 44 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +22 -10
+
+static int loongson_dwmac_acpi_config(struct pci_dev *pdev,
+				      struct plat_stmmacenet_data *plat,
+				      struct stmmac_resources *res)
+{
+	if (!pdev->irq)
+		return -EINVAL;
+
+	res->irq = pdev->irq;
+
+	return 0;
+}
+
+static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+	struct plat_stmmacenet_data *plat;
+	struct stmmac_pci_info *info;
+	struct stmmac_resources res;
+	int ret, i;
+
 	plat = devm_kzalloc(&pdev->dev, sizeof(*plat), GFP_KERNEL);
 	if (!plat)
 		return -ENOMEM;
@@ -90,17 +146,9 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
 	if (!plat->mdio_bus_data)
 		return -ENOMEM;
 
-	plat->mdio_node = of_get_child_by_name(np, "mdio");
-	if (plat->mdio_node) {
-		dev_info(&pdev->dev, "Found MDIO subnode\n");
-		plat->mdio_bus_data->needs_reset = true;
-	}
-
 	plat->dma_cfg = devm_kzalloc(&pdev->dev, sizeof(*plat->dma_cfg), GFP_KERNEL);
-	if (!plat->dma_cfg) {
-		ret = -ENOMEM;
-		goto err_put_node;
-	}
+	if (!plat->dma_cfg)
+		return -ENOMEM;
 
 	/* Enable pci device */
 	ret = pci_enable_device(pdev);

drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id · line 158

Quoted 2 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +0 -0
@@ -109,6 +157,8 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
 
 		goto err_put_node;
		return ret;
Quoted 52 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +2 -0
 	}
 
+	pci_set_master(pdev);
+
 	/* Get the base address of device */
 	for (i = 0; i < PCI_STD_NUM_BARS; i++) {
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +1 -33
 		if (pci_resource_len(pdev, i) == 0)
@@ -119,48 +169,20 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
 		break;
 	}
 
-	plat->bus_id = of_alias_get_id(np, "ethernet");
-	if (plat->bus_id < 0)
-		plat->bus_id = pci_dev_id(pdev);
-
-	phy_mode = device_get_phy_mode(&pdev->dev);
-	if (phy_mode < 0) {
-		dev_err(&pdev->dev, "phy_mode not found\n");
-		ret = phy_mode;
-		goto err_disable_device;
-	}
-
-	plat->phy_interface = phy_mode;
-
-	pci_set_master(pdev);
-
 	memset(&res, 0, sizeof(res));
 	res.addr = pcim_iomap_table(pdev)[0];
 
 	info = (struct stmmac_pci_info *)id->driver_data;
-	ret = info->setup(plat);
+	ret = info->setup(pdev, plat);
 	if (ret)
 		goto err_disable_device;
 
-	res.irq = of_irq_get_byname(np, "macirq");
-	if (res.irq < 0) {
-		dev_err(&pdev->dev, "IRQ macirq not found\n");
-		ret = -ENODEV;
-		goto err_disable_device;
-	}
-
-	res.wol_irq = of_irq_get_byname(np, "eth_wake_irq");
-	if (res.wol_irq < 0) {
-		dev_info(&pdev->dev, "IRQ eth_wake_irq not found, using macirq\n");
-		res.wol_irq = res.irq;
-	}
-
-	res.lpi_irq = of_irq_get_byname(np, "eth_lpi");
-	if (res.lpi_irq < 0) {
-		dev_err(&pdev->dev, "IRQ eth_lpi not found\n");
-		ret = -ENODEV;

drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id · line 188

Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +5 -1
+	if (dev_of_node(&pdev->dev))
+		ret = loongson_dwmac_dt_config(pdev, plat, &res);
+	else
+		ret = loongson_dwmac_acpi_config(pdev, plat, &res);
+	if (ret)
 		goto err_disable_device;
-	}
 
 	ret = stmmac_dvr_probe(&pdev->dev, plat, &res);
 	if (ret)

... make sure loongson_dwmac_dt_clear() is called in the cleanup-on-error path:

        ret = stmmac_dvr_probe(&pdev->dev, plat, &res);
        if (ret)
                goto err_plat_clear;

        return 0;

err_plat_clear:

	if (dev_of_node(&pdev->dev))
		loongson_dwmac_dt_clear(pdev, plat);

err_disable_device:

        pci_disable_device(pdev);

        return ret;

... and in the loongson_dwmac_remove() method:

static void loongson_dwmac_remove(struct pci_dev *pdev)

{
	...

        stmmac_dvr_remove(&pdev->dev);

	if (dev_of_node(&pdev->dev))
		loongson_dwmac_dt_clear(pdev, priv->plat);

	...
}

-Serge(y)

Quoted 3 lines
Signature · 1 line
2.31.4
author
#19 lore raw

PATCH v14 12/14 net: stmmac: dwmac-loongson: Add Loongson Multi-channels GMAC support

In reply to Yanteng Si

The Loongson DWMAC driver currently supports the Loongson GMAC devices (based on the DW GMAC v3.50a/v3.73a IP-core) installed to the LS2K1000 SoC and LS7A1000 chipset. But recently a new generation LS2K2000 SoC was released with the new version of the Loongson GMAC synthesized in. The new controller is based on the DW GMAC v3.73a IP-core with the AV-feature enabled, which implies the multi DMA-channels support. The multi DMA-channels feature has the next vendor-specific peculiarities:

1. Split up Tx and Rx DMA IRQ status/mask bits:
Name Tx Rx

  DMA_INTR_ENA_NIE = 0x00040000 | 0x00020000;
  DMA_INTR_ENA_AIE = 0x00010000 | 0x00008000;
  DMA_STATUS_NIS   = 0x00040000 | 0x00020000;
  DMA_STATUS_AIS   = 0x00010000 | 0x00008000;
  DMA_STATUS_FBI   = 0x00002000 | 0x00001000;

2. Custom Synopsys ID hardwired into the GMAC_VERSION.SNPSVER register field. It's 0x10 while it should have been 0x37 in accordance with the actual DW GMAC IP-core version.
3. There are eight DMA-channels available meanwhile the Synopsys DW GMAC IP-core supports up to three DMA-channels.
4. It's possible to have each DMA-channel IRQ independently delivered. The MSI IRQs must be utilized for that.

Thus in order to have the multi-channels Loongson GMAC controllers supported let's modify the Loongson DWMAC driver in accordance with all the peculiarities described above:

1. Create the multi-channels Loongson GMAC-specific stmmac_dma_ops::dma_interrupt() stmmac_dma_ops::init_chan()
callbacks due to the non-standard DMA IRQ CSR flags layout.
2. Create the Loongson DWMAC-specific platform setup() method which gets to initialize the DMA-ops with the dwmac1000_dma_ops instance and overrides the callbacks described in 1. The method also overrides the custom Synopsys ID with the real one in order to have the rest of the HW-specific callbacks correctly detected by the driver core.
3. Make sure the platform setup() method enables the flow control and duplex modes supported by the controller.

---
 drivers/net/ethernet/stmicro/stmmac/common.h  |   1 +
 .../ethernet/stmicro/stmmac/dwmac-loongson.c  | 341 +++++++++++++++++-
 2 files changed, 339 insertions(+), 3 deletions(-)
drivers/net/ethernet/stmicro/stmmac/common.h +1 -0
index cd36ff4da68c..684489156dce 100644
@@ -29,6 +29,7 @@
 /* Synopsys Core versions */
 #define	DWMAC_CORE_3_40		0x34
 #define	DWMAC_CORE_3_50		0x35
+#define	DWMAC_CORE_3_70		0x37
 #define	DWMAC_CORE_4_00		0x40
 #define DWMAC_CORE_4_10		0x41
 #define DWMAC_CORE_5_00		0x50
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +338 -3

406 lines not on this page · raw message

Signature · 1 line
2.31.4
#20 lore raw

Re: [PATCH net-next v14 12/14] net: stmmac: dwmac-loongson: Add Loongson Multi-channels GMAC support

Quoted 118 lines · Yanteng Si

The Loongson DWMAC driver currently supports the Loongson GMAC devices (based on the DW GMAC v3.50a/v3.73a IP-core) installed to the LS2K1000 SoC and LS7A1000 chipset. But recently a new generation LS2K2000 SoC was released with the new version of the Loongson GMAC synthesized in. The new controller is based on the DW GMAC v3.73a IP-core with the AV-feature enabled, which implies the multi DMA-channels support. The multi DMA-channels feature has the next vendor-specific peculiarities:

1. Split up Tx and Rx DMA IRQ status/mask bits:
Name Tx Rx

  DMA_INTR_ENA_NIE = 0x00040000 | 0x00020000;
  DMA_INTR_ENA_AIE = 0x00010000 | 0x00008000;
  DMA_STATUS_NIS   = 0x00040000 | 0x00020000;
  DMA_STATUS_AIS   = 0x00010000 | 0x00008000;
  DMA_STATUS_FBI   = 0x00002000 | 0x00001000;

2. Custom Synopsys ID hardwired into the GMAC_VERSION.SNPSVER register field. It's 0x10 while it should have been 0x37 in accordance with the actual DW GMAC IP-core version.
3. There are eight DMA-channels available meanwhile the Synopsys DW GMAC IP-core supports up to three DMA-channels.
4. It's possible to have each DMA-channel IRQ independently delivered. The MSI IRQs must be utilized for that.

Thus in order to have the multi-channels Loongson GMAC controllers supported let's modify the Loongson DWMAC driver in accordance with all the peculiarities described above:

1. Create the multi-channels Loongson GMAC-specific stmmac_dma_ops::dma_interrupt() stmmac_dma_ops::init_chan()
callbacks due to the non-standard DMA IRQ CSR flags layout.
2. Create the Loongson DWMAC-specific platform setup() method which gets to initialize the DMA-ops with the dwmac1000_dma_ops instance and overrides the callbacks described in 1. The method also overrides the custom Synopsys ID with the real one in order to have the rest of the HW-specific callbacks correctly detected by the driver core.
3. Make sure the platform setup() method enables the flow control and duplex modes supported by the controller.

---
 drivers/net/ethernet/stmicro/stmmac/common.h  |   1 +
 .../ethernet/stmicro/stmmac/dwmac-loongson.c  | 341 +++++++++++++++++-
 2 files changed, 339 insertions(+), 3 deletions(-)
drivers/net/ethernet/stmicro/stmmac/common.h +1 -0
index cd36ff4da68c..684489156dce 100644
@@ -29,6 +29,7 @@
 /* Synopsys Core versions */
 #define	DWMAC_CORE_3_40		0x34
 #define	DWMAC_CORE_3_50		0x35
+#define	DWMAC_CORE_3_70		0x37
 #define	DWMAC_CORE_4_00		0x40
 #define DWMAC_CORE_4_10		0x41
 #define DWMAC_CORE_5_00		0x50
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +49 -0
index b4704068321f..ed45d6e56de2 100644
@@ -8,8 +8,70 @@
 #include <linux/device.h>
 #include <linux/of_irq.h>
 #include "stmmac.h"
+#include "dwmac_dma.h"
+#include "dwmac1000.h"
+
+/* Normal Loongson Tx Summary */
+#define DMA_INTR_ENA_NIE_TX_LOONGSON	0x00040000
+/* Normal Loongson Rx Summary */
+#define DMA_INTR_ENA_NIE_RX_LOONGSON	0x00020000
+
+#define DMA_INTR_NORMAL_LOONGSON	(DMA_INTR_ENA_NIE_TX_LOONGSON | \
+					 DMA_INTR_ENA_NIE_RX_LOONGSON | \
+					 DMA_INTR_ENA_RIE | DMA_INTR_ENA_TIE)
+
+/* Abnormal Loongson Tx Summary */
+#define DMA_INTR_ENA_AIE_TX_LOONGSON	0x00010000
+/* Abnormal Loongson Rx Summary */
+#define DMA_INTR_ENA_AIE_RX_LOONGSON	0x00008000
+
+#define DMA_INTR_ABNORMAL_LOONGSON	(DMA_INTR_ENA_AIE_TX_LOONGSON | \
+					 DMA_INTR_ENA_AIE_RX_LOONGSON | \
+					 DMA_INTR_ENA_FBE | DMA_INTR_ENA_UNE)
+
+#define DMA_INTR_DEFAULT_MASK_LOONGSON	(DMA_INTR_NORMAL_LOONGSON | \
+					 DMA_INTR_ABNORMAL_LOONGSON)
+
+/* Normal Loongson Tx Interrupt Summary */
+#define DMA_STATUS_NIS_TX_LOONGSON	0x00040000
+/* Normal Loongson Rx Interrupt Summary */
+#define DMA_STATUS_NIS_RX_LOONGSON	0x00020000
+
+/* Abnormal Loongson Tx Interrupt Summary */
+#define DMA_STATUS_AIS_TX_LOONGSON	0x00010000
+/* Abnormal Loongson Rx Interrupt Summary */
+#define DMA_STATUS_AIS_RX_LOONGSON	0x00008000
+
+/* Fatal Loongson Tx Bus Error Interrupt */
+#define DMA_STATUS_FBI_TX_LOONGSON	0x00002000
+/* Fatal Loongson Rx Bus Error Interrupt */
+#define DMA_STATUS_FBI_RX_LOONGSON	0x00001000
+
+#define DMA_STATUS_MSK_COMMON_LOONGSON	(DMA_STATUS_NIS_TX_LOONGSON | \
+					 DMA_STATUS_NIS_RX_LOONGSON | \
+					 DMA_STATUS_AIS_TX_LOONGSON | \
+					 DMA_STATUS_AIS_RX_LOONGSON | \
+					 DMA_STATUS_FBI_TX_LOONGSON | \
+					 DMA_STATUS_FBI_RX_LOONGSON)
+
+#define DMA_STATUS_MSK_RX_LOONGSON	(DMA_STATUS_ERI | DMA_STATUS_RWT | \
+					 DMA_STATUS_RPS | DMA_STATUS_RU  | \
+					 DMA_STATUS_RI  | DMA_STATUS_OVF | \

drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c line 69

Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +7 -0
+					 DMA_STATUS_MSK_COMMON_LOONGSON)
+
+#define DMA_STATUS_MSK_TX_LOONGSON	(DMA_STATUS_ETI | DMA_STATUS_UNF | \
+					 DMA_STATUS_TJT | DMA_STATUS_TU  | \
+					 DMA_STATUS_TPS | DMA_STATUS_TI  | \
+					 DMA_STATUS_MSK_COMMON_LOONGSON)
 
 #define PCI_DEVICE_ID_LOONGSON_GMAC	0x7a03
 
+#define DWMAC_CORE_LS_MULTICHAN	0x10	/* Loongson custom IP */

s/Loongson custom IP/Loongson custom ID

drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c

Quoted 6 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +5 -0
+#define CHANNEL_NUM			8
+
+struct loongson_data {
+	u32 loongson_id;
 
+	struct device *dev;

Move this field adding to the next patch.

Quoted 204 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +1 -0
+};
 

struct stmmac_pci_info {

drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +185 -2
 	int (*setup)(struct pci_dev *pdev, struct plat_stmmacenet_data *plat);
@@ -56,10 +118,26 @@ static void loongson_default_data(struct pci_dev *pdev,
 static int loongson_gmac_data(struct pci_dev *pdev,
 			      struct plat_stmmacenet_data *plat)
 {
+	struct loongson_data *ld;
+	int i;
+
+	ld = plat->bsp_priv;
+
 	loongson_default_data(pdev, plat);
 
-	plat->tx_queues_to_use = 1;
-	plat->rx_queues_to_use = 1;
+	if (ld->loongson_id == DWMAC_CORE_LS_MULTICHAN) {
+		plat->rx_queues_to_use = CHANNEL_NUM;
+		plat->tx_queues_to_use = CHANNEL_NUM;
+
+		/* Only channel 0 supports checksum,
+		 * so turn off checksum to enable multiple channels.
+		 */
+		for (i = 1; i < CHANNEL_NUM; i++)
+			plat->tx_queues_cfg[i].coe_unsupported = 1;
+	} else {
+		plat->tx_queues_to_use = 1;
+		plat->rx_queues_to_use = 1;
+	}
 
 	plat->phy_interface = PHY_INTERFACE_MODE_RGMII_ID;
 
@@ -70,6 +148,239 @@ static struct stmmac_pci_info loongson_gmac_pci_info = {
 	.setup = loongson_gmac_data,
 };
 
+static void loongson_dwmac_dma_init_channel(struct stmmac_priv *priv,
+					    void __iomem *ioaddr,
+					    struct stmmac_dma_cfg *dma_cfg,
+					    u32 chan)
+{
+	int txpbl = dma_cfg->txpbl ?: dma_cfg->pbl;
+	int rxpbl = dma_cfg->rxpbl ?: dma_cfg->pbl;
+	u32 value;
+
+	value = readl(ioaddr + DMA_CHAN_BUS_MODE(chan));
+
+	if (dma_cfg->pblx8)
+		value |= DMA_BUS_MODE_MAXPBL;
+
+	value |= DMA_BUS_MODE_USP;
+	value &= ~(DMA_BUS_MODE_PBL_MASK | DMA_BUS_MODE_RPBL_MASK);
+	value |= (txpbl << DMA_BUS_MODE_PBL_SHIFT);
+	value |= (rxpbl << DMA_BUS_MODE_RPBL_SHIFT);
+
+	/* Set the Fixed burst mode */
+	if (dma_cfg->fixed_burst)
+		value |= DMA_BUS_MODE_FB;
+
+	/* Mixed Burst has no effect when fb is set */
+	if (dma_cfg->mixed_burst)
+		value |= DMA_BUS_MODE_MB;
+
+	if (dma_cfg->atds)
+		value |= DMA_BUS_MODE_ATDS;
+
+	if (dma_cfg->aal)
+		value |= DMA_BUS_MODE_AAL;
+
+	writel(value, ioaddr + DMA_CHAN_BUS_MODE(chan));
+
+	/* Mask interrupts by writing to CSR7 */
+	writel(DMA_INTR_DEFAULT_MASK_LOONGSON, ioaddr +
+	       DMA_CHAN_INTR_ENA(chan));
+}
+
+static int loongson_dwmac_dma_interrupt(struct stmmac_priv *priv,
+					void __iomem *ioaddr,
+					struct stmmac_extra_stats *x,
+					u32 chan, u32 dir)
+{
+	struct stmmac_pcpu_stats *stats = this_cpu_ptr(priv->xstats.pcpu_stats);
+	u32 abnor_intr_status;
+	u32 nor_intr_status;
+	u32 fb_intr_status;
+	u32 intr_status;
+	int ret = 0;
+
+	/* read the status register (CSR5) */
+	intr_status = readl(ioaddr + DMA_CHAN_STATUS(chan));
+
+	if (dir == DMA_DIR_RX)
+		intr_status &= DMA_STATUS_MSK_RX_LOONGSON;
+	else if (dir == DMA_DIR_TX)
+		intr_status &= DMA_STATUS_MSK_TX_LOONGSON;
+
+	nor_intr_status = intr_status & (DMA_STATUS_NIS_TX_LOONGSON |
+		DMA_STATUS_NIS_RX_LOONGSON);
+	abnor_intr_status = intr_status & (DMA_STATUS_AIS_TX_LOONGSON |
+		DMA_STATUS_AIS_RX_LOONGSON);
+	fb_intr_status = intr_status & (DMA_STATUS_FBI_TX_LOONGSON |
+		DMA_STATUS_FBI_RX_LOONGSON);
+
+	/* ABNORMAL interrupts */
+	if (unlikely(abnor_intr_status)) {
+		if (unlikely(intr_status & DMA_STATUS_UNF)) {
+			ret = tx_hard_error_bump_tc;
+			x->tx_undeflow_irq++;
+		}
+		if (unlikely(intr_status & DMA_STATUS_TJT))
+			x->tx_jabber_irq++;
+		if (unlikely(intr_status & DMA_STATUS_OVF))
+			x->rx_overflow_irq++;
+		if (unlikely(intr_status & DMA_STATUS_RU))
+			x->rx_buf_unav_irq++;
+		if (unlikely(intr_status & DMA_STATUS_RPS))
+			x->rx_process_stopped_irq++;
+		if (unlikely(intr_status & DMA_STATUS_RWT))
+			x->rx_watchdog_irq++;
+		if (unlikely(intr_status & DMA_STATUS_ETI))
+			x->tx_early_irq++;
+		if (unlikely(intr_status & DMA_STATUS_TPS)) {
+			x->tx_process_stopped_irq++;
+			ret = tx_hard_error;
+		}
+		if (unlikely(fb_intr_status)) {
+			x->fatal_bus_error_irq++;
+			ret = tx_hard_error;
+		}
+	}
+	/* TX/RX NORMAL interrupts */
+	if (likely(nor_intr_status)) {
+		if (likely(intr_status & DMA_STATUS_RI)) {
+			u32 value = readl(ioaddr + DMA_INTR_ENA);
+			/* to schedule NAPI on real RIE event. */
+			if (likely(value & DMA_INTR_ENA_RIE)) {
+				u64_stats_update_begin(&stats->syncp);
+				u64_stats_inc(&stats->rx_normal_irq_n[chan]);
+				u64_stats_update_end(&stats->syncp);
+				ret |= handle_rx;
+			}
+		}
+		if (likely(intr_status & DMA_STATUS_TI)) {
+			u64_stats_update_begin(&stats->syncp);
+			u64_stats_inc(&stats->tx_normal_irq_n[chan]);
+			u64_stats_update_end(&stats->syncp);
+			ret |= handle_tx;
+		}
+		if (unlikely(intr_status & DMA_STATUS_ERI))
+			x->rx_early_irq++;
+	}
+	/* Optional hardware blocks, interrupts should be disabled */
+	if (unlikely(intr_status &
+		     (DMA_STATUS_GPI | DMA_STATUS_GMI | DMA_STATUS_GLI)))
+		pr_warn("%s: unexpected status %08x\n", __func__, intr_status);
+
+	/* Clear the interrupt by writing a logic 1 to the CSR5[19-0] */
+	writel((intr_status & 0x7ffff), ioaddr + DMA_CHAN_STATUS(chan));
+
+	return ret;
+}
+
+static struct mac_device_info *loongson_dwmac_setup(void *apriv)
+{
+	struct stmmac_priv *priv = apriv;
+	struct mac_device_info *mac;
+	struct stmmac_dma_ops *dma;
+	struct loongson_data *ld;
+	struct pci_dev *pdev;
+
+	ld = priv->plat->bsp_priv;
+	pdev = to_pci_dev(priv->device);
+
+	mac = devm_kzalloc(priv->device, sizeof(*mac), GFP_KERNEL);
+	if (!mac)
+		return NULL;
+
+	dma = devm_kzalloc(priv->device, sizeof(*dma), GFP_KERNEL);
+	if (!dma)
+		return NULL;
+
+	/* The Loongson GMAC devices are based on the DW GMAC
+	 * v3.50a and v3.73a IP-cores. But the HW designers have changed the
+	 * GMAC_VERSION.SNPSVER field to the custom 0x10 value on the
+	 * network controllers with the multi-channels feature
+	 * available to emphasize the differences: multiple DMA-channels,
+	 * AV feature and GMAC_INT_STATUS CSR flags layout. Get back the
+	 * original value so the correct HW-interface would be selected.
+	 */
+	if (ld->loongson_id == DWMAC_CORE_LS_MULTICHAN) {
+		priv->synopsys_id = DWMAC_CORE_3_70;
+		*dma = dwmac1000_dma_ops;
+		dma->init_chan = loongson_dwmac_dma_init_channel;
+		dma->dma_interrupt = loongson_dwmac_dma_interrupt;
+		mac->dma = dma;
+	}
+
+	priv->dev->priv_flags |= IFF_UNICAST_FLT;
+
+	/* Pre-initialize the respective "mac" fields as it's done in
+	 * dwmac1000_setup()
+	 */
+	mac->pcsr = priv->ioaddr;

drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 327

Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +9 -0
+	mac->multicast_filter_bins = priv->plat->multicast_filter_bins;
+	mac->unicast_filter_entries = priv->plat->unicast_filter_entries;
+	mac->mcast_bits_log2 = 0;
+
+	if (mac->multicast_filter_bins)
+		mac->mcast_bits_log2 = ilog2(mac->multicast_filter_bins);
+
+	/* Loongson GMAC doesn't support the flow control. */
 
+	if (pdev->device == PCI_DEVICE_ID_LOONGSON_GMAC)

This if-statement should be added in the next patch since at this patch stage the only supported device is Loongson GMAC so ...

drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 327

Quoted 1 line
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +1 -0
+		mac->link.caps = MAC_10 | MAC_100 | MAC_1000;

... the caps initialisation is supposed to be performed unconditionally.

Quoted 38 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +38 -0
+
+	mac->link.duplex = GMAC_CONTROL_DM;
+	mac->link.speed10 = GMAC_CONTROL_PS;
+	mac->link.speed100 = GMAC_CONTROL_PS | GMAC_CONTROL_FES;
+	mac->link.speed1000 = 0;
+	mac->link.speed_mask = GMAC_CONTROL_PS | GMAC_CONTROL_FES;
+	mac->mii.addr = GMAC_MII_ADDR;
+	mac->mii.data = GMAC_MII_DATA;
+	mac->mii.addr_shift = 11;
+	mac->mii.addr_mask = 0x0000F800;
+	mac->mii.reg_shift = 6;
+	mac->mii.reg_mask = 0x000007C0;
+	mac->mii.clk_csr_shift = 2;
+	mac->mii.clk_csr_mask = GENMASK(5, 2);
+
+	return mac;
+}
+
+static int loongson_dwmac_msi_config(struct pci_dev *pdev,
+				     struct plat_stmmacenet_data *plat,
+				     struct stmmac_resources *res)
+{
+	int i, ret, vecs;
+
+	vecs = roundup_pow_of_two(CHANNEL_NUM * 2 + 1);
+	ret = pci_alloc_irq_vectors(pdev, vecs, vecs, PCI_IRQ_MSI);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Failed to allocate PCI IRQs\n");
+		return ret;
+	}
+
+	res->irq = pci_irq_vector(pdev, 0);
+
+	if (ret >= vecs) {
+		for (i = 0; i < plat->rx_queues_to_use; i++) {
+			res->rx_irq[CHANNEL_NUM - 1 - i] =
+				pci_irq_vector(pdev, 1 + i * 2);
+		}

drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 375

Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +10 -0
+		for (i = 0; i < plat->tx_queues_to_use; i++) {
+			res->tx_irq[CHANNEL_NUM - 1 - i] =
+				pci_irq_vector(pdev, 2 + i * 2);
+		}
+
+		plat->flags |= STMMAC_FLAG_MULTI_MSI_EN;
+	}
+
+	return 0;
+}

I deliberately emphasized to note the pci_alloc_irq_vectors() arguments. Passing the same min and max means to request the exact amount of MSI vectors. So there is no need in checking the returned value for being greater than vecs.

Moreover as we figured out on v13, the multi-channel-ness still works even if no MSI allocated. The only difference is that all the events will be delivered via the MAC IRQ:
https://lore.kernel.org/netdev/[email protected]/

So AFAICS the method can be simplified like this:

+static int loongson_dwmac_msi_config(struct pci_dev *pdev,
+ struct plat_stmmacenet_data *plat,
+ struct stmmac_resources *res)
+{
+ int i, ret, vecs;
+
+ vecs = roundup_pow_of_two(CHANNEL_NUM * 2 + 1);
+ ret = pci_alloc_irq_vectors(pdev, vecs, vecs, PCI_IRQ_MSI);
+ if (ret < 0) {
+ dev_warn(&pdev->dev, "Failed to allocate MSI IRQs\n");
+ return ret;
+ }
+
+ res->irq = pci_irq_vector(pdev, 0);
+
+ for (i = 0; i < plat->rx_queues_to_use; i++) {
+ res->rx_irq[CHANNEL_NUM - 1 - i] =
+ pci_irq_vector(pdev, 1 + i * 2);
+ }
+
+ for (i = 0; i < plat->tx_queues_to_use; i++) {
+ res->tx_irq[CHANNEL_NUM - 1 - i] =
+ pci_irq_vector(pdev, 2 + i * 2);
+ }
+
+ plat->flags |= STMMAC_FLAG_MULTI_MSI_EN;
+
+ return 0;
+}

Please once again note the omitted (ret > vecs) conditional statement and using the dev_warn("... MSI IRQS ...") instead of dev_err(), since having MSI isn't required for the device to work.

drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static struct stmmac_pci_info loongson_gmac_pci_info = { · line 382

Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +7 -0
+
 
+static int loongson_dwmac_msi_clear(struct pci_dev *pdev)
+{
+	pci_free_irq_vectors(pdev);
+
+	return 0;
+}

Please convert it to returning void.

Quoted 24 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +1 -0
+
 static int loongson_dwmac_dt_config(struct pci_dev *pdev,
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +5 -0
 				    struct plat_stmmacenet_data *plat,
 				    struct stmmac_resources *res)
@@ -134,6 +445,7 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
 	struct plat_stmmacenet_data *plat;
 	struct stmmac_pci_info *info;
 	struct stmmac_resources res;
+	struct loongson_data *ld;
 	int ret, i;
 
 	plat = devm_kzalloc(&pdev->dev, sizeof(*plat), GFP_KERNEL);
@@ -150,6 +462,10 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
 	if (!plat->dma_cfg)
 		return -ENOMEM;
 
+	ld = devm_kzalloc(&pdev->dev, sizeof(*ld), GFP_KERNEL);
+	if (!ld)
+		return -ENOMEM;
+
 	/* Enable pci device */
 	ret = pci_enable_device(pdev);
 	if (ret) {

drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id · line 494

Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +3 -0
@@ -172,6 +488,11 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
 	memset(&res, 0, sizeof(res));
 	res.addr = pcim_iomap_table(pdev)[0];
 
+	plat->bsp_priv = ld;
+	plat->setup = loongson_dwmac_setup;
 
+	ld->dev = &pdev->dev;

Move this line to the next patch.

Quoted 6 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +2 -0
+	ld->loongson_id = readl(res.addr + GMAC_VERSION) & 0xff;
+
 	info = (struct stmmac_pci_info *)id->driver_data;
 	ret = info->setup(pdev, plat);
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +0 -0
 	if (ret)

drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id · line 513

Quoted 9 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +5 -0
@@ -184,12 +505,21 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
 	if (ret)
 		goto err_disable_device;
 
 
+	if (ld->loongson_id == DWMAC_CORE_LS_MULTICHAN) {
+		ret = loongson_dwmac_msi_config(pdev, plat, &res);
+		if (ret)
+			goto err_disable_device;
+	}

Since MSIs isn't required for the Multi-channels device to work this can be converted to:

	/* Use the common MAC IRQ if per-channel MSIs allocation failed */
	if (ld->loongson_id == DWMAC_CORE_LS_MULTICHAN)
		loongson_dwmac_msi_config(pdev, plat, &res);

-Serge(y)

Quoted 38 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +5 -1
+
 	ret = stmmac_dvr_probe(&pdev->dev, plat, &res);
 	if (ret)
-		goto err_disable_device;
+		goto err_clear_msi;
 
 	return ret;
 
+err_clear_msi:
+	if (ld->loongson_id == DWMAC_CORE_LS_MULTICHAN)
+		loongson_dwmac_msi_clear(pdev);
 err_disable_device:
 	pci_disable_device(pdev);

err_put_node:

drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +5 -0
@@ -201,8 +531,10 @@ static void loongson_dwmac_remove(struct pci_dev *pdev)
 {
 	struct net_device *ndev = dev_get_drvdata(&pdev->dev);
 	struct stmmac_priv *priv = netdev_priv(ndev);
+	struct loongson_data *ld;
 	int i;
 
+	ld = priv->plat->bsp_priv;
 	of_node_put(priv->plat->mdio_node);
 	stmmac_dvr_remove(&pdev->dev);
 
@@ -213,6 +545,9 @@ static void loongson_dwmac_remove(struct pci_dev *pdev)
 		break;
 	}
 
+	if (ld->loongson_id == DWMAC_CORE_LS_MULTICHAN)
+		loongson_dwmac_msi_clear(pdev);
+
 	pci_disable_device(pdev);
 }
 
Signature · 1 line
2.31.4
author
#21 lore raw

PATCH v14 13/14 net: stmmac: dwmac-loongson: Add Loongson GNET support

In reply to Yanteng Si

The new generation Loongson LS2K2000 SoC and LS7A2000 chipset are equipped with the network controllers called Loongson GNET. It's the single and multi DMA-channels Loongson GMAC but with a PHY attached. Here is the summary of the DW GMAC features the controller has:

DW GMAC IP-core: v3.73a
Speeds: 10/100/1000Mbps
Duplex: Full (both versions), Half (LS2K2000 GNET only) DMA-descriptors type: enhanced
L3/L4 filters availability: Y
VLAN hash table filter: Y
PHY-interface: GMII (PHY is integrated into the chips) Remote Wake-up support: Y
Mac Management Counters (MMC): Y
Number of additional MAC addresses: 5
MAC Hash-based filter: Y
Hash Table Size: 256
AV feature: Y (LS2K2000 GNET only)
DMA channels: 8 (LS2K2000 GNET), 1 (LS7A2000 GNET)

Let's update the Loongson DWMAC driver to supporting the new Loongson GNET controller. The change is mainly trivial: the driver shall be bound to the PCIe device with DID 0x7a13, and the device-specific setup() method shall be called for it. The only peculiarity concerns the integrated PHY speed change procedure. The PHY has a weird problem with switching from the low speeds to 1000Mbps mode. The speedup procedure requires the PHY-link re-negotiation. So the suggested change provide the device-specific fix_mac_speed() method to overcome the problem.

---
 .../ethernet/stmicro/stmmac/dwmac-loongson.c  | 72 ++++++++++++++++++-
 1 file changed, 69 insertions(+), 3 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +69 -3
index ed45d6e56de2..3fed7292b755 100644
@@ -65,6 +65,7 @@
 					 DMA_STATUS_MSK_COMMON_LOONGSON)
 
 #define PCI_DEVICE_ID_LOONGSON_GMAC	0x7a03
+#define PCI_DEVICE_ID_LOONGSON_GNET	0x7a13
 #define DWMAC_CORE_LS_MULTICHAN	0x10	/* Loongson custom IP */
 #define CHANNEL_NUM			8
 
@@ -148,6 +149,60 @@ static struct stmmac_pci_info loongson_gmac_pci_info = {
 	.setup = loongson_gmac_data,
 };
 
+static void loongson_gnet_fix_speed(void *priv, unsigned int speed,
+				    unsigned int mode)
+{
+	struct loongson_data *ld = (struct loongson_data *)priv;
+	struct net_device *ndev = dev_get_drvdata(ld->dev);
+	struct stmmac_priv *ptr = netdev_priv(ndev);
+
+	/* The integrated PHY has a weird problem with switching from the low
+	 * speeds to 1000Mbps mode. The speedup procedure requires the PHY-link
+	 * re-negotiation.
+	 */
+	if (speed == SPEED_1000) {
+		if (readl(ptr->ioaddr + MAC_CTRL_REG) &
+		    GMAC_CONTROL_PS)
+			/* Word around hardware bug, restart autoneg */
+			phy_restart_aneg(ndev->phydev);
+	}
+}
+
+static int loongson_gnet_data(struct pci_dev *pdev,
+			      struct plat_stmmacenet_data *plat)
+{
+	struct loongson_data *ld;
+	int i;
+
+	ld = plat->bsp_priv;
+
+	loongson_default_data(pdev, plat);
+
+	if (ld->loongson_id == DWMAC_CORE_LS_MULTICHAN) {
+		plat->rx_queues_to_use = CHANNEL_NUM;
+		plat->tx_queues_to_use = CHANNEL_NUM;
+
+		/* Only channel 0 supports checksum,
+		 * so turn off checksum to enable multiple channels.
+		 */
+		for (i = 1; i < CHANNEL_NUM; i++)
+			plat->tx_queues_cfg[i].coe_unsupported = 1;
+	} else {
+		plat->tx_queues_to_use = 1;
+		plat->rx_queues_to_use = 1;
+	}
+
+	plat->phy_interface = PHY_INTERFACE_MODE_GMII;
+	plat->mdio_bus_data->phy_mask = ~(u32)BIT(2);
+	plat->fix_mac_speed = loongson_gnet_fix_speed;
+
+	return 0;
+}
+
+static struct stmmac_pci_info loongson_gnet_pci_info = {
+	.setup = loongson_gnet_data,
+};
+
 static void loongson_dwmac_dma_init_channel(struct stmmac_priv *priv,
 					    void __iomem *ioaddr,
 					    struct stmmac_dma_cfg *dma_cfg,
@@ -293,7 +348,7 @@ static struct mac_device_info *loongson_dwmac_setup(void *apriv)
 	if (!dma)
 		return NULL;
 
-	/* The Loongson GMAC devices are based on the DW GMAC
+	/* The Loongson GMAC and GNET devices are based on the DW GMAC
 	 * v3.50a and v3.73a IP-cores. But the HW designers have changed the
 	 * GMAC_VERSION.SNPSVER field to the custom 0x10 value on the
 	 * network controllers with the multi-channels feature
@@ -322,9 +377,19 @@ static struct mac_device_info *loongson_dwmac_setup(void *apriv)
 	if (mac->multicast_filter_bins)
 		mac->mcast_bits_log2 = ilog2(mac->multicast_filter_bins);
 
-	/* Loongson GMAC doesn't support the flow control. */
-	if (pdev->device == PCI_DEVICE_ID_LOONGSON_GMAC)
+	/* Loongson GMAC doesn't support the flow control. LS2K2000
+	 * GNET doesn't support the half-duplex link mode.
+	 */
+	if (pdev->device == PCI_DEVICE_ID_LOONGSON_GMAC) {
 		mac->link.caps = MAC_10 | MAC_100 | MAC_1000;
+	} else {
+		if (ld->loongson_id == DWMAC_CORE_LS_MULTICHAN)
+			mac->link.caps = MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
+					 MAC_10 | MAC_100 | MAC_1000;
+		else
+			mac->link.caps = MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
+					 MAC_10FD | MAC_100FD | MAC_1000FD;
+	}
 
 	mac->link.duplex = GMAC_CONTROL_DM;
 	mac->link.speed10 = GMAC_CONTROL_PS;
@@ -591,6 +656,7 @@ static SIMPLE_DEV_PM_OPS(loongson_dwmac_pm_ops, loongson_dwmac_suspend,
 
 static const struct pci_device_id loongson_dwmac_id_table[] = {
 	{ PCI_DEVICE_DATA(LOONGSON, GMAC, &loongson_gmac_pci_info) },
+	{ PCI_DEVICE_DATA(LOONGSON, GNET, &loongson_gnet_pci_info) },
 	{}
 };
 MODULE_DEVICE_TABLE(pci, loongson_dwmac_id_table);
Signature · 1 line
2.31.4
author
#22 lore raw

PATCH v14 14/14 net: stmmac: dwmac-loongson: Add loongson module author

In reply to Yanteng Si

Add Yanteng Si as MODULE_AUTHOR of Loongson DWMAC PCI driver.

---
 drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c | 1 +
 1 file changed, 1 insertion(+)
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +1 -0
index 3fed7292b755..4e4c23049a7d 100644
@@ -675,4 +675,5 @@ module_pci_driver(loongson_dwmac_driver);
 
 MODULE_DESCRIPTION("Loongson DWMAC PCI driver");
 MODULE_AUTHOR("Qing Zhang <[email protected]>");
+MODULE_AUTHOR("Yanteng Si <[email protected]>");
 MODULE_LICENSE("GPL v2");
Signature · 1 line
2.31.4
Acked-by on the v14 series
#23 lore raw
In reply to Yanteng Si

Hi, Yanteng,

Thank you for your hard work on this driver. This series is good enough for me, so for the whole series:

Quoted 320 lines · Yanteng Si

v14:

Because Loongson GMAC can be also found with the 8-channels AV feature
enabled, we'll need to reconsider the patches logic and thus the
commit logs too. As Serge's comments and Russell's comments:
[PATCH net-next v14 01/15] net: stmmac: Move the atds flag to the stmmac_dma_cfg structure [PATCH net-next v14 02/15] net: stmmac: Add multi-channel support
[PATCH net-next v14 03/15] net: stmmac: Export dwmac1000_dma_ops
[PATCH net-next v14 04/15] net: stmmac: dwmac-loongson: Drop duplicated hash-based filter size init [PATCH net-next v14 05/15] net: stmmac: dwmac-loongson: Drop pci_enable/disable_msi calls [PATCH net-next v14 06/15] net: stmmac: dwmac-loongson: Use PCI_DEVICE_DATA() macro for device identification [PATCH net-next v14 07/15] net: stmmac: dwmac-loongson: Detach GMAC-specific platform data init +-> Init the plat_stmmacenet_data::{tx_queues_to_use,rx_queues_to_use}
in the loongson_gmac_data() method.
[PATCH net-next v14 08/15] net: stmmac: dwmac-loongson: Init ref and PTP clocks rate
[PATCH net-next v14 09/15] net: stmmac: dwmac-loongson: Add phy_interface for Loongson GMAC [PATCH net-next v14 10/15] net: stmmac: dwmac-loongson: Introduce PCI device info data
+-> Make sure the setup() method is called after the pci_enable_device()
invocation.
[PATCH net-next v14 11/15] net: stmmac: dwmac-loongson: Add DT-less GMAC PCI-device support +-> Introduce the loongson_dwmac_dt_config() method here instead of
doing that in a separate patch.
+-> Add loongson_dwmac_acpi_config() which would just get the IRQ from

    the pdev->irq field and make sure it is valid.

[PATCH net-next v14 12/15] net: stmmac: Fixed failure to set network speed to 1000. +-> Drop the patch as Russell's comments, At the same time, he provided another
better repair suggestion, and I decided to send it separately after the patch set was merged. See:
<https://lore.kernel.org/netdev/[email protected]/>
[PATCH net-next v14 13/15] net: stmmac: dwmac-loongson: Add Loongson Multi-channels GMAC support +-> This is former "net: stmmac: dwmac-loongson: Add Loongson GNET
support" patch, but which adds the support of the Loongson GMAC with the 8-channels AV-feature available.
+-> loongson_dwmac_intx_config() shall be dropped due to the
loongson_dwmac_acpi_config() method added in the PATCH 11/15.
+-> Make sure loongson_data::loongson_id is initialized before the
stmmac_pci_info::setup() is called.
+-> Move the rx_queues_to_use/tx_queues_to_use and coe_unsupported
fields initialization to the loongson_gmac_data() method.
+-> As before, call the loongson_dwmac_msi_config() method if the multi-channels
Loongson MAC has been detected.
+-> Move everything GNET-specific to the next patch.
[PATCH net-next v14 14/15] net: stmmac: dwmac-loongson: Add Loongson GNET support +-> Everything Loonsgson GNET-specific is supposed to be added in the
framework of this patch:
+ PCI_DEVICE_ID_LOONGSON_GNET macro
+ loongson_gnet_fix_speed() method
+ loongson_gnet_data() method
+ loongson_gnet_pci_info data
+ The GNET-specific part of the loongson_dwmac_setup() method.
+ ...
[PATCH net-next v14 15/15] net: stmmac: dwmac-loongson: Add loongson module author

Other's:
Pick Serge's Reviewed-by tag.

v13:

* Sorry, we have clarified some things in the past 10 days. I did not give you a clear reply to the following questions in v12, so I need to reply again:

1. The current LS2K2000 also have a GMAC(and two GNET) that supports 8 channels, so we have to reconsider the initialization of tx/rx_queues_to_use into probe();

2. In v12, we disagreed on the loongson_dwmac_msi_config method, but I changed

    it based on Serge's comments(If I understand correctly):
        if (dev_of_node(&pdev->dev)) {
                ret = loongson_dwmac_dt_config(pdev, plat, &res);
        }

        if (ld->loongson_id == DWMAC_CORE_LS2K2000) {
                ret = loongson_dwmac_msi_config(pdev, plat, &res);
        } else {
                ret = loongson_dwmac_intx_config(pdev, plat, &res);
        }

3. Our priv->dma_cap.pcs is false, so let's use PHY_INTERFACE_MODE_NA;

4. Our GMAC does not support Delay, so let's use PHY_INTERFACE_MODE_RGMII_ID, the current dts is wrong, a fix patch will be sent to the LoongArch list later.

Others:
* Re-split a part of the patch (it seems we do this with every version);
* Copied Serge's comments into the commit message of patch;
* Fixed the stmmac_dma_operation_mode() method;
* Changed some code comments.

v12:
* The biggest change is the re-splitting of patches.
* Add a "gmac_version" in loongson_data, then we only read it once in the _probe().
* Drop Serge's patch.
* Rebase to the latest code state.
* Fixed the gnet commit message.

v11:
* Break loongson_phylink_get_caps(), fix bad logic.
* Remove a unnecessary ";".
* Remove some unnecessary "{}".
* add a blank.
* Move the code of fix _force_1000 to patch 6/6.

The main changes occur in these two functions:
loongson_dwmac_probe();
loongson_dwmac_setup();

v10:
As Andrew's comment:
* Add a #define for the 0x37.
* Add a #define for Port Select.

others:
* Pick Serge's patch, This patch resulted from the process of reviewing our patch set.
* Based on Serge's patch, modify our loongson_phylink_get_caps().
* Drop patch 3/6, we need mac_interface.
* Adjusted the code layout of gnet patch.
* Corrected several errata in commit message.
* Move DISABLE_FORCE flag to loongson_gnet_data().

v9:
We have not provided a detailed list of equipment for a long time, and I apologize for this. During this period, I have collected some information and now present it to you, hoping to alleviate the pressure of review.

1. IP core
We now have two types of IP cores, one is 0x37, similar to dwmac1000; The other is 0x10. Compared to 0x37, we split several DMA registers from one to two, and it is not worth adding a new entry for this. According to Serge's comment, we made these devices work by overwriting priv->synopsys_id = 0x37 and mac->dma = <LS_dma_ops>.

1.1. Some more detailed information
The number of DMA channels for 0x37 is 1; The number of DMA channels for 0x10 is 8. Except for channel 0, otherchannels do not support sending hardware checksums. Supported AV features are Qav, Qat, and Qas, and the rest are consistent with 3.73.

2. DEVICE
We have two types of devices,
one is GMAC, which only has a MAC chip inside and needs an external PHY chip;
the other is GNET, which integrates both MAC and PHY chips inside.

2.1. Some more detailed information
GMAC device: LS7A1000, LS2K1000, these devices do not support any pause mode.
gnet device: LS7A2000, LS2K2000, the chip connection between the mac and
phy of these devices is not normal and requires two rounds of negotiation; LS7A2000 does not support half-duplex and
multi-channel;
to enable multi-channel on LS2K2000, you need to turn off
hardware checksum.
**Note**: Only the LS2K2000's IP core is 0x10, while the IP cores of other devices are 0x37.

3. TABLE

device    type    pci_id    ip_core
ls7a1000  gmac    7a03      0x35/0x37
ls2k1000  gmac    7a03      0x35/0x37
ls7a2000  gnet    7a13      0x37
ls2k2000  gnet    7a13      0x10

-----------------------------------------------
Changes:

* passed the CI
<https://github.com/linux-netdev/nipa/blob/main/tests/patch/checkpatch
/checkpatch.sh>
* reverse xmas tree order.
* Silence build warning.
* Re-split the patch.
* Add more detailed commit message.
* Add more code comment.
* Reduce modification of generic code.
* using the GNET-specific prefix.
* define a new macro for the GNET MAC.
* Use an easier way to overwrite mac.
* Removed some useless printk.

v8:
* The biggest change is according to Serge's comment in the previous edition:
Seeing the patch in the current state would overcomplicate the generic code and the only functions you need to update are dwmac_dma_interrupt()
dwmac1000_dma_init_channel()
you can have these methods re-defined with all the Loongson GNET specifics in the low-level platform driver (dwmac-loongson.c). After that you can just override the mac_device_info.dma pointer with a fixed stmmac_dma_ops descriptor. Here is what should be done for that:

1. Keep the Patch 4/9 with my comments fixed. First it will be partly useful for your GNET device. Second in general it's a correct implementation of the normal DW GMAC v3.x multi-channels feature and will be useful for the DW GMACs with that feature enabled.

2. Create the Loongson GNET-specific stmmac_dma_ops.dma_interrupt()
stmmac_dma_ops.init_chan()
methods in the dwmac-loongson.c driver. Don't forget to move all the Loongson-specific macros from dwmac_dma.h to dwmac-loongson.c.

3. Create a Loongson GNET-specific platform setup method with the next semantics:
+ allocate stmmac_dma_ops instance and initialize it with dwmac1000_dma_ops.
+ override the stmmac_dma_ops.{dma_interrupt, init_chan} with the pointers to the methods defined in 2.
+ allocate mac_device_info instance and initialize the mac_device_info.dma field with a pointer to the new stmmac_dma_ops instance.
+ call dwmac1000_setup() or initialize mac_device_info in a way it's done in dwmac1000_setup() (the later might be better so you wouldn't need to export the dwmac1000_setup() function).
+ override stmmac_priv.synopsys_id with a correct value.

4. Initialize plat_stmmacenet_data.setup() with the pointer to the method created in 3.

* Others:
Re-split the patch.
Passed checkpatch.pl test.

v7:
* Refer to andrew's suggestion:
- Add DMA_INTR_ENA_NIE_RX and DMA_INTR_ENA_NIE_TX #define's, etc.

* Others:
- Using --subject-prefix="PATCH net-next vN" to indicate that the patches are for the networking tree.
- Rebase to the latest networking tree:
<git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git>

v6:

* Refer to Serge's suggestion:
- Add new platform feature flag:
include/linux/stmmac.h:
+#define STMMAC_FLAG_HAS_LGMAC BIT(13)

- Add the IRQs macros specific to the Loongson Multi-channels GMAC:

     drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h:
     +#define DMA_INTR_ENA_NIE_LOONGSON 0x00060000      /* ...*/
     #define DMA_INTR_ENA_NIE 0x00010000        /* Normal Summary */
     ...

- Drop all of redundant changes that don't require the prototypes being converted to accepting the stmmac_priv pointer.

* Refer to andrew's suggestion:
- Drop white space changes.
- break patch up into lots of smaller parts.
Some small patches have been put into another series as a preparation see <https://lore.kernel.org/loongarch/[email protected]/T/#t>

*note* : This series of patches relies on the three small patches above.
* others
- Drop irq_flags changes.
- Changed patch order.

v4 -> v5:

* Remove an ugly and useless patch (fix channel number).
* Remove the non-standard dma64 driver code, and also remove the HWIF entries, since the associated custom callbacks no longer exist.
* Refer to Serge's suggestion: Update the dwmac1000_dma.c to support the multi-DMA-channels controller setup.

See:
v4: <https://lore.kernel.org/loongarch/[email protected]/>
v3: <https://lore.kernel.org/loongarch/[email protected]/>
v2: <https://lore.kernel.org/loongarch/[email protected]/>
v1: <https://lore.kernel.org/loongarch/[email protected]/>

Yanteng Si (14):
net: stmmac: Move the atds flag to the stmmac_dma_cfg structure
net: stmmac: Add multi-channel support
net: stmmac: Export dwmac1000_dma_ops
net: stmmac: dwmac-loongson: Drop duplicated hash-based filter size
init
net: stmmac: dwmac-loongson: Drop pci_enable/disable_msi calls
net: stmmac: dwmac-loongson: Use PCI_DEVICE_DATA() macro for device
identification
net: stmmac: dwmac-loongson: Detach GMAC-specific platform data init
net: stmmac: dwmac-loongson: Init ref and PTP clocks rate
net: stmmac: dwmac-loongson: Add phy_interface for Loongson GMAC
net: stmmac: dwmac-loongson: Introduce PCI device info data
net: stmmac: dwmac-loongson: Add DT-less GMAC PCI-device support
net: stmmac: dwmac-loongson: Add Loongson Multi-channels GMAC support
net: stmmac: dwmac-loongson: Add Loongson GNET support
net: stmmac: dwmac-loongson: Add loongson module author

 drivers/net/ethernet/stmicro/stmmac/common.h  |   1 +
 .../ethernet/stmicro/stmmac/dwmac-loongson.c  | 572 ++++++++++++++++--
 .../net/ethernet/stmicro/stmmac/dwmac-sun8i.c |   4 +-
 .../ethernet/stmicro/stmmac/dwmac1000_dma.c   |  35 +-
 .../ethernet/stmicro/stmmac/dwmac100_dma.c    |   2 +-
 .../net/ethernet/stmicro/stmmac/dwmac4_dma.c  |   2 +-
 .../net/ethernet/stmicro/stmmac/dwmac_dma.h   |  27 +-
 .../net/ethernet/stmicro/stmmac/dwmac_lib.c   |  30 +-
 .../ethernet/stmicro/stmmac/dwxgmac2_dma.c    |   2 +-
 drivers/net/ethernet/stmicro/stmmac/hwif.h    |   5 +-
 .../net/ethernet/stmicro/stmmac/stmmac_main.c |  19 +-
 include/linux/stmmac.h                        |   1 +
 12 files changed, 587 insertions(+), 113 deletions(-)

--
2.31.4

#24 lore raw
In reply to Yanteng Si

Hi Yanteng

Quoted 53 lines · Yanteng Si

v14:

Because Loongson GMAC can be also found with the 8-channels AV feature
enabled, we'll need to reconsider the patches logic and thus the
commit logs too. As Serge's comments and Russell's comments:
[PATCH net-next v14 01/15] net: stmmac: Move the atds flag to the stmmac_dma_cfg structure [PATCH net-next v14 02/15] net: stmmac: Add multi-channel support
[PATCH net-next v14 03/15] net: stmmac: Export dwmac1000_dma_ops
[PATCH net-next v14 04/15] net: stmmac: dwmac-loongson: Drop duplicated hash-based filter size init [PATCH net-next v14 05/15] net: stmmac: dwmac-loongson: Drop pci_enable/disable_msi calls [PATCH net-next v14 06/15] net: stmmac: dwmac-loongson: Use PCI_DEVICE_DATA() macro for device identification [PATCH net-next v14 07/15] net: stmmac: dwmac-loongson: Detach GMAC-specific platform data init +-> Init the plat_stmmacenet_data::{tx_queues_to_use,rx_queues_to_use}
in the loongson_gmac_data() method.
[PATCH net-next v14 08/15] net: stmmac: dwmac-loongson: Init ref and PTP clocks rate
[PATCH net-next v14 09/15] net: stmmac: dwmac-loongson: Add phy_interface for Loongson GMAC [PATCH net-next v14 10/15] net: stmmac: dwmac-loongson: Introduce PCI device info data
+-> Make sure the setup() method is called after the pci_enable_device()
invocation.
[PATCH net-next v14 11/15] net: stmmac: dwmac-loongson: Add DT-less GMAC PCI-device support +-> Introduce the loongson_dwmac_dt_config() method here instead of
doing that in a separate patch.
+-> Add loongson_dwmac_acpi_config() which would just get the IRQ from

    the pdev->irq field and make sure it is valid.

[PATCH net-next v14 12/15] net: stmmac: Fixed failure to set network speed to 1000. +-> Drop the patch as Russell's comments, At the same time, he provided another
better repair suggestion, and I decided to send it separately after the patch set was merged. See:
<https://lore.kernel.org/netdev/[email protected]/>
[PATCH net-next v14 13/15] net: stmmac: dwmac-loongson: Add Loongson Multi-channels GMAC support +-> This is former "net: stmmac: dwmac-loongson: Add Loongson GNET
support" patch, but which adds the support of the Loongson GMAC with the 8-channels AV-feature available.
+-> loongson_dwmac_intx_config() shall be dropped due to the
loongson_dwmac_acpi_config() method added in the PATCH 11/15.
+-> Make sure loongson_data::loongson_id is initialized before the
stmmac_pci_info::setup() is called.
+-> Move the rx_queues_to_use/tx_queues_to_use and coe_unsupported
fields initialization to the loongson_gmac_data() method.
+-> As before, call the loongson_dwmac_msi_config() method if the multi-channels
Loongson MAC has been detected.
+-> Move everything GNET-specific to the next patch.
[PATCH net-next v14 14/15] net: stmmac: dwmac-loongson: Add Loongson GNET support +-> Everything Loonsgson GNET-specific is supposed to be added in the
framework of this patch:
+ PCI_DEVICE_ID_LOONGSON_GNET macro
+ loongson_gnet_fix_speed() method
+ loongson_gnet_data() method
+ loongson_gnet_pci_info data
+ The GNET-specific part of the loongson_dwmac_setup() method.
+ ...
[PATCH net-next v14 15/15] net: stmmac: dwmac-loongson: Add loongson module author

Quoted 2 lines

Other's:
Pick Serge's Reviewed-by tag.

Thanks for submitting an update. I've briefly looked at it and spotted a few places left to improve. I'll send my comments on the next week.

-Serge(y)

Quoted 264 lines

v13:

* Sorry, we have clarified some things in the past 10 days. I did not give you a clear reply to the following questions in v12, so I need to reply again:

1. The current LS2K2000 also have a GMAC(and two GNET) that supports 8 channels, so we have to reconsider the initialization of tx/rx_queues_to_use into probe();

2. In v12, we disagreed on the loongson_dwmac_msi_config method, but I changed

    it based on Serge's comments(If I understand correctly):
	if (dev_of_node(&pdev->dev)) {
		ret = loongson_dwmac_dt_config(pdev, plat, &res);
	}

	if (ld->loongson_id == DWMAC_CORE_LS2K2000) {
		ret = loongson_dwmac_msi_config(pdev, plat, &res);
	} else {
		ret = loongson_dwmac_intx_config(pdev, plat, &res);
	}

3. Our priv->dma_cap.pcs is false, so let's use PHY_INTERFACE_MODE_NA;

4. Our GMAC does not support Delay, so let's use PHY_INTERFACE_MODE_RGMII_ID, the current dts is wrong, a fix patch will be sent to the LoongArch list later.

Others:
* Re-split a part of the patch (it seems we do this with every version);
* Copied Serge's comments into the commit message of patch;
* Fixed the stmmac_dma_operation_mode() method;
* Changed some code comments.

v12:
* The biggest change is the re-splitting of patches.
* Add a "gmac_version" in loongson_data, then we only read it once in the _probe().
* Drop Serge's patch.
* Rebase to the latest code state.
* Fixed the gnet commit message.

v11:
* Break loongson_phylink_get_caps(), fix bad logic.
* Remove a unnecessary ";".
* Remove some unnecessary "{}".
* add a blank.
* Move the code of fix _force_1000 to patch 6/6.

The main changes occur in these two functions:
loongson_dwmac_probe();
loongson_dwmac_setup();

v10:
As Andrew's comment:
* Add a #define for the 0x37.
* Add a #define for Port Select.

others:
* Pick Serge's patch, This patch resulted from the process of reviewing our patch set.
* Based on Serge's patch, modify our loongson_phylink_get_caps().
* Drop patch 3/6, we need mac_interface.
* Adjusted the code layout of gnet patch.
* Corrected several errata in commit message.
* Move DISABLE_FORCE flag to loongson_gnet_data().

v9:
We have not provided a detailed list of equipment for a long time, and I apologize for this. During this period, I have collected some information and now present it to you, hoping to alleviate the pressure of review.

1. IP core
We now have two types of IP cores, one is 0x37, similar to dwmac1000; The other is 0x10. Compared to 0x37, we split several DMA registers from one to two, and it is not worth adding a new entry for this. According to Serge's comment, we made these devices work by overwriting priv->synopsys_id = 0x37 and mac->dma = <LS_dma_ops>.

1.1. Some more detailed information
The number of DMA channels for 0x37 is 1; The number of DMA channels for 0x10 is 8. Except for channel 0, otherchannels do not support sending hardware checksums. Supported AV features are Qav, Qat, and Qas, and the rest are consistent with 3.73.

2. DEVICE
We have two types of devices,
one is GMAC, which only has a MAC chip inside and needs an external PHY chip;
the other is GNET, which integrates both MAC and PHY chips inside.

2.1. Some more detailed information
GMAC device: LS7A1000, LS2K1000, these devices do not support any pause mode.
gnet device: LS7A2000, LS2K2000, the chip connection between the mac and
phy of these devices is not normal and requires two rounds of negotiation; LS7A2000 does not support half-duplex and
multi-channel;
to enable multi-channel on LS2K2000, you need to turn off
hardware checksum.
**Note**: Only the LS2K2000's IP core is 0x10, while the IP cores of other devices are 0x37.

3. TABLE

device    type    pci_id    ip_core
ls7a1000  gmac    7a03      0x35/0x37
ls2k1000  gmac    7a03      0x35/0x37
ls7a2000  gnet    7a13      0x37
ls2k2000  gnet    7a13      0x10

-----------------------------------------------
Changes:

* passed the CI
<https://github.com/linux-netdev/nipa/blob/main/tests/patch/checkpatch
/checkpatch.sh>
* reverse xmas tree order.
* Silence build warning.
* Re-split the patch.
* Add more detailed commit message.
* Add more code comment.
* Reduce modification of generic code.
* using the GNET-specific prefix.
* define a new macro for the GNET MAC.
* Use an easier way to overwrite mac.
* Removed some useless printk.

v8:
* The biggest change is according to Serge's comment in the previous edition:
Seeing the patch in the current state would overcomplicate the generic code and the only functions you need to update are dwmac_dma_interrupt()
dwmac1000_dma_init_channel()
you can have these methods re-defined with all the Loongson GNET specifics in the low-level platform driver (dwmac-loongson.c). After that you can just override the mac_device_info.dma pointer with a fixed stmmac_dma_ops descriptor. Here is what should be done for that:

1. Keep the Patch 4/9 with my comments fixed. First it will be partly useful for your GNET device. Second in general it's a correct implementation of the normal DW GMAC v3.x multi-channels feature and will be useful for the DW GMACs with that feature enabled.

2. Create the Loongson GNET-specific stmmac_dma_ops.dma_interrupt()
stmmac_dma_ops.init_chan()
methods in the dwmac-loongson.c driver. Don't forget to move all the Loongson-specific macros from dwmac_dma.h to dwmac-loongson.c.

3. Create a Loongson GNET-specific platform setup method with the next semantics:
+ allocate stmmac_dma_ops instance and initialize it with dwmac1000_dma_ops.
+ override the stmmac_dma_ops.{dma_interrupt, init_chan} with the pointers to the methods defined in 2.
+ allocate mac_device_info instance and initialize the mac_device_info.dma field with a pointer to the new stmmac_dma_ops instance.
+ call dwmac1000_setup() or initialize mac_device_info in a way it's done in dwmac1000_setup() (the later might be better so you wouldn't need to export the dwmac1000_setup() function).
+ override stmmac_priv.synopsys_id with a correct value.

4. Initialize plat_stmmacenet_data.setup() with the pointer to the method created in 3.

* Others:
Re-split the patch.
Passed checkpatch.pl test.

v7:
* Refer to andrew's suggestion:
- Add DMA_INTR_ENA_NIE_RX and DMA_INTR_ENA_NIE_TX #define's, etc.

* Others:
- Using --subject-prefix="PATCH net-next vN" to indicate that the patches are for the networking tree.
- Rebase to the latest networking tree:
<git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git>

v6:

* Refer to Serge's suggestion:
- Add new platform feature flag:

    include/linux/stmmac.h:
    +#define STMMAC_FLAG_HAS_LGMAC			BIT(13)

- Add the IRQs macros specific to the Loongson Multi-channels GMAC:

     drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h:
     +#define DMA_INTR_ENA_NIE_LOONGSON 0x00060000      /* ...*/
     #define DMA_INTR_ENA_NIE 0x00010000	/* Normal Summary */
     ...

- Drop all of redundant changes that don't require the prototypes being converted to accepting the stmmac_priv pointer.

* Refer to andrew's suggestion:
- Drop white space changes.
- break patch up into lots of smaller parts.
Some small patches have been put into another series as a preparation see <https://lore.kernel.org/loongarch/[email protected]/T/#t>

*note* : This series of patches relies on the three small patches above.
* others
- Drop irq_flags changes.
- Changed patch order.

v4 -> v5:

* Remove an ugly and useless patch (fix channel number).
* Remove the non-standard dma64 driver code, and also remove the HWIF entries, since the associated custom callbacks no longer exist.
* Refer to Serge's suggestion: Update the dwmac1000_dma.c to support the multi-DMA-channels controller setup.

See:
v4: <https://lore.kernel.org/loongarch/[email protected]/>
v3: <https://lore.kernel.org/loongarch/[email protected]/>
v2: <https://lore.kernel.org/loongarch/[email protected]/>
v1: <https://lore.kernel.org/loongarch/[email protected]/>

Yanteng Si (14):
net: stmmac: Move the atds flag to the stmmac_dma_cfg structure
net: stmmac: Add multi-channel support
net: stmmac: Export dwmac1000_dma_ops
net: stmmac: dwmac-loongson: Drop duplicated hash-based filter size
init
net: stmmac: dwmac-loongson: Drop pci_enable/disable_msi calls
net: stmmac: dwmac-loongson: Use PCI_DEVICE_DATA() macro for device
identification
net: stmmac: dwmac-loongson: Detach GMAC-specific platform data init
net: stmmac: dwmac-loongson: Init ref and PTP clocks rate
net: stmmac: dwmac-loongson: Add phy_interface for Loongson GMAC
net: stmmac: dwmac-loongson: Introduce PCI device info data
net: stmmac: dwmac-loongson: Add DT-less GMAC PCI-device support
net: stmmac: dwmac-loongson: Add Loongson Multi-channels GMAC support
net: stmmac: dwmac-loongson: Add Loongson GNET support
net: stmmac: dwmac-loongson: Add loongson module author

 drivers/net/ethernet/stmicro/stmmac/common.h  |   1 +
 .../ethernet/stmicro/stmmac/dwmac-loongson.c  | 572 ++++++++++++++++--
 .../net/ethernet/stmicro/stmmac/dwmac-sun8i.c |   4 +-
 .../ethernet/stmicro/stmmac/dwmac1000_dma.c   |  35 +-
 .../ethernet/stmicro/stmmac/dwmac100_dma.c    |   2 +-
 .../net/ethernet/stmicro/stmmac/dwmac4_dma.c  |   2 +-
 .../net/ethernet/stmicro/stmmac/dwmac_dma.h   |  27 +-
 .../net/ethernet/stmicro/stmmac/dwmac_lib.c   |  30 +-
 .../ethernet/stmicro/stmmac/dwxgmac2_dma.c    |   2 +-
 drivers/net/ethernet/stmicro/stmmac/hwif.h    |   5 +-
 .../net/ethernet/stmicro/stmmac/stmmac_main.c |  19 +-
 include/linux/stmmac.h                        |   1 +
 12 files changed, 587 insertions(+), 113 deletions(-)
Signature · 1 line
2.31.4
author
#25 lore raw
Quoted 56 lines · Serge Semin

Hi Yanteng

Quoted 53 lines · Yanteng Si

v14:

Because Loongson GMAC can be also found with the 8-channels AV feature
enabled, we'll need to reconsider the patches logic and thus the
commit logs too. As Serge's comments and Russell's comments:
[PATCH net-next v14 01/15] net: stmmac: Move the atds flag to the stmmac_dma_cfg structure [PATCH net-next v14 02/15] net: stmmac: Add multi-channel support
[PATCH net-next v14 03/15] net: stmmac: Export dwmac1000_dma_ops
[PATCH net-next v14 04/15] net: stmmac: dwmac-loongson: Drop duplicated hash-based filter size init [PATCH net-next v14 05/15] net: stmmac: dwmac-loongson: Drop pci_enable/disable_msi calls [PATCH net-next v14 06/15] net: stmmac: dwmac-loongson: Use PCI_DEVICE_DATA() macro for device identification [PATCH net-next v14 07/15] net: stmmac: dwmac-loongson: Detach GMAC-specific platform data init +-> Init the plat_stmmacenet_data::{tx_queues_to_use,rx_queues_to_use}
in the loongson_gmac_data() method.
[PATCH net-next v14 08/15] net: stmmac: dwmac-loongson: Init ref and PTP clocks rate
[PATCH net-next v14 09/15] net: stmmac: dwmac-loongson: Add phy_interface for Loongson GMAC [PATCH net-next v14 10/15] net: stmmac: dwmac-loongson: Introduce PCI device info data
+-> Make sure the setup() method is called after the pci_enable_device()
invocation.
[PATCH net-next v14 11/15] net: stmmac: dwmac-loongson: Add DT-less GMAC PCI-device support +-> Introduce the loongson_dwmac_dt_config() method here instead of
doing that in a separate patch.
+-> Add loongson_dwmac_acpi_config() which would just get the IRQ from

     the pdev->irq field and make sure it is valid.

[PATCH net-next v14 12/15] net: stmmac: Fixed failure to set network speed to 1000. +-> Drop the patch as Russell's comments, At the same time, he provided another
better repair suggestion, and I decided to send it separately after the patch set was merged. See:
<https://lore.kernel.org/netdev/[email protected]/>
[PATCH net-next v14 13/15] net: stmmac: dwmac-loongson: Add Loongson Multi-channels GMAC support +-> This is former "net: stmmac: dwmac-loongson: Add Loongson GNET
support" patch, but which adds the support of the Loongson GMAC with the 8-channels AV-feature available.
+-> loongson_dwmac_intx_config() shall be dropped due to the
loongson_dwmac_acpi_config() method added in the PATCH 11/15.

+-> Make sure loongson_data::loongson_id  is initialized before the
     stmmac_pci_info::setup()  is called.
+-> Move the rx_queues_to_use/tx_queues_to_use and coe_unsupported

fields initialization to the loongson_gmac_data() method.
+-> As before, call the loongson_dwmac_msi_config() method if the multi-channels
Loongson MAC has been detected.
+-> Move everything GNET-specific to the next patch.
[PATCH net-next v14 14/15] net: stmmac: dwmac-loongson: Add Loongson GNET support +-> Everything Loonsgson GNET-specific is supposed to be added in the
framework of this patch:
+ PCI_DEVICE_ID_LOONGSON_GNET macro
+ loongson_gnet_fix_speed() method
+ loongson_gnet_data() method
+ loongson_gnet_pci_info data
+ The GNET-specific part of the loongson_dwmac_setup() method.
+ ...
[PATCH net-next v14 15/15] net: stmmac: dwmac-loongson: Add loongson module author

Quoted 4 lines
Quoted 2 lines

Other's:
Pick Serge's Reviewed-by tag.

Thanks for submitting an update. I've briefly looked at it and spotted a few places left to improve. I'll send my comments on the next week.

Okay, thank you for spending a lot of time and effort reviewing our patch.

Thanks,

Yanteng

#26 lore raw

Hi Yanteng

Quoted 58 lines · Yanteng Si
Quoted 56 lines · Serge Semin

Hi Yanteng

Quoted 53 lines · Yanteng Si

v14:

Because Loongson GMAC can be also found with the 8-channels AV feature
enabled, we'll need to reconsider the patches logic and thus the
commit logs too. As Serge's comments and Russell's comments:
[PATCH net-next v14 01/15] net: stmmac: Move the atds flag to the stmmac_dma_cfg structure [PATCH net-next v14 02/15] net: stmmac: Add multi-channel support
[PATCH net-next v14 03/15] net: stmmac: Export dwmac1000_dma_ops
[PATCH net-next v14 04/15] net: stmmac: dwmac-loongson: Drop duplicated hash-based filter size init [PATCH net-next v14 05/15] net: stmmac: dwmac-loongson: Drop pci_enable/disable_msi calls [PATCH net-next v14 06/15] net: stmmac: dwmac-loongson: Use PCI_DEVICE_DATA() macro for device identification [PATCH net-next v14 07/15] net: stmmac: dwmac-loongson: Detach GMAC-specific platform data init +-> Init the plat_stmmacenet_data::{tx_queues_to_use,rx_queues_to_use}
in the loongson_gmac_data() method.
[PATCH net-next v14 08/15] net: stmmac: dwmac-loongson: Init ref and PTP clocks rate
[PATCH net-next v14 09/15] net: stmmac: dwmac-loongson: Add phy_interface for Loongson GMAC [PATCH net-next v14 10/15] net: stmmac: dwmac-loongson: Introduce PCI device info data
+-> Make sure the setup() method is called after the pci_enable_device()
invocation.
[PATCH net-next v14 11/15] net: stmmac: dwmac-loongson: Add DT-less GMAC PCI-device support +-> Introduce the loongson_dwmac_dt_config() method here instead of
doing that in a separate patch.
+-> Add loongson_dwmac_acpi_config() which would just get the IRQ from

     the pdev->irq field and make sure it is valid.

[PATCH net-next v14 12/15] net: stmmac: Fixed failure to set network speed to 1000. +-> Drop the patch as Russell's comments, At the same time, he provided another
better repair suggestion, and I decided to send it separately after the patch set was merged. See:
<https://lore.kernel.org/netdev/[email protected]/>
[PATCH net-next v14 13/15] net: stmmac: dwmac-loongson: Add Loongson Multi-channels GMAC support +-> This is former "net: stmmac: dwmac-loongson: Add Loongson GNET
support" patch, but which adds the support of the Loongson GMAC with the 8-channels AV-feature available.
+-> loongson_dwmac_intx_config() shall be dropped due to the
loongson_dwmac_acpi_config() method added in the PATCH 11/15.

+-> Make sure loongson_data::loongson_id  is initialized before the
     stmmac_pci_info::setup()  is called.
+-> Move the rx_queues_to_use/tx_queues_to_use and coe_unsupported

fields initialization to the loongson_gmac_data() method.
+-> As before, call the loongson_dwmac_msi_config() method if the multi-channels
Loongson MAC has been detected.
+-> Move everything GNET-specific to the next patch.
[PATCH net-next v14 14/15] net: stmmac: dwmac-loongson: Add Loongson GNET support +-> Everything Loonsgson GNET-specific is supposed to be added in the
framework of this patch:
+ PCI_DEVICE_ID_LOONGSON_GNET macro
+ loongson_gnet_fix_speed() method
+ loongson_gnet_data() method
+ loongson_gnet_pci_info data
+ The GNET-specific part of the loongson_dwmac_setup() method.
+ ...
[PATCH net-next v14 15/15] net: stmmac: dwmac-loongson: Add loongson module author

Quoted 6 lines
Quoted 4 lines
Quoted 2 lines

Other's:
Pick Serge's Reviewed-by tag.

Thanks for submitting an update. I've briefly looked at it and spotted a few places left to improve. I'll send my comments on the next week.

Okay, thank you for spending a lot of time and effort reviewing our patch.

In case if you are willing to resubmit the series anytime soon, please note that 6.11 merge window was opened two days ago. So the series either need to be submitted as RFC v15 or you need to hold on with posting the patch set for the next two weeks.

-Serge(y)

Quoted 6 lines

Thanks,

Yanteng

author
#27 lore raw
Quoted 62 lines · Serge Semin

Hi Yanteng

Quoted 59 lines · Yanteng Si
Quoted 58 lines · Serge Semin

Hi Yanteng

Quoted 55 lines · Yanteng Si

v14:

Because Loongson GMAC can be also found with the 8-channels AV feature
enabled, we'll need to reconsider the patches logic and thus the
commit logs too. As Serge's comments and Russell's comments:
[PATCH net-next v14 01/15] net: stmmac: Move the atds flag to the stmmac_dma_cfg structure [PATCH net-next v14 02/15] net: stmmac: Add multi-channel support
[PATCH net-next v14 03/15] net: stmmac: Export dwmac1000_dma_ops
[PATCH net-next v14 04/15] net: stmmac: dwmac-loongson: Drop duplicated hash-based filter size init [PATCH net-next v14 05/15] net: stmmac: dwmac-loongson: Drop pci_enable/disable_msi calls [PATCH net-next v14 06/15] net: stmmac: dwmac-loongson: Use PCI_DEVICE_DATA() macro for device identification [PATCH net-next v14 07/15] net: stmmac: dwmac-loongson: Detach GMAC-specific platform data init +-> Init the plat_stmmacenet_data::{tx_queues_to_use,rx_queues_to_use}
in the loongson_gmac_data() method.
[PATCH net-next v14 08/15] net: stmmac: dwmac-loongson: Init ref and PTP clocks rate
[PATCH net-next v14 09/15] net: stmmac: dwmac-loongson: Add phy_interface for Loongson GMAC [PATCH net-next v14 10/15] net: stmmac: dwmac-loongson: Introduce PCI device info data
+-> Make sure the setup() method is called after the pci_enable_device()
invocation.
[PATCH net-next v14 11/15] net: stmmac: dwmac-loongson: Add DT-less GMAC PCI-device support +-> Introduce the loongson_dwmac_dt_config() method here instead of
doing that in a separate patch.
+-> Add loongson_dwmac_acpi_config() which would just get the IRQ from

      the pdev->irq field and make sure it is valid.

[PATCH net-next v14 12/15] net: stmmac: Fixed failure to set network speed to 1000. +-> Drop the patch as Russell's comments, At the same time, he provided another
better repair suggestion, and I decided to send it separately after the patch set was merged. See:
<https://lore.kernel.org/netdev/[email protected]/>
[PATCH net-next v14 13/15] net: stmmac: dwmac-loongson: Add Loongson Multi-channels GMAC support +-> This is former "net: stmmac: dwmac-loongson: Add Loongson GNET
support" patch, but which adds the support of the Loongson GMAC with the 8-channels AV-feature available.
+-> loongson_dwmac_intx_config() shall be dropped due to the
loongson_dwmac_acpi_config() method added in the PATCH 11/15.

+-> Make sure loongson_data::loongson_id  is initialized before the
      stmmac_pci_info::setup()  is called.
+-> Move the rx_queues_to_use/tx_queues_to_use and coe_unsupported

fields initialization to the loongson_gmac_data() method.
+-> As before, call the loongson_dwmac_msi_config() method if the multi-channels
Loongson MAC has been detected.
+-> Move everything GNET-specific to the next patch.
[PATCH net-next v14 14/15] net: stmmac: dwmac-loongson: Add Loongson GNET support +-> Everything Loonsgson GNET-specific is supposed to be added in the
framework of this patch:
+ PCI_DEVICE_ID_LOONGSON_GNET macro
+ loongson_gnet_fix_speed() method
+ loongson_gnet_data() method
+ loongson_gnet_pci_info data
+ The GNET-specific part of the loongson_dwmac_setup() method.
+ ...
[PATCH net-next v14 15/15] net: stmmac: dwmac-loongson: Add loongson module author

Other's:
Pick Serge's Reviewed-by tag.

Quoted 8 lines
Quoted 3 lines
Quoted 2 lines

Thanks for submitting an update. I've briefly looked at it and spotted a few places left to improve. I'll send my comments on the next week.

Okay, thank you for spending a lot of time and effort reviewing our patch.

In case if you are willing to resubmit the series anytime soon, please note that 6.11 merge window was opened two days ago. So the series either need to be submitted as RFC v15 or you need to hold on with posting the patch set for the next two weeks.

Thanks, I will send RFC v15.

Thanks,

Yanteng