where do i start?
to everyone,
hi people, am new with this things(advance routing/traffic control). my query is this, i will be testing out this setup.
i have already bridge a 2-port ethernet card(ex eth2, eth3), not physically assigning any ip address to this ports. the bridge was assigned with an ip instead. now, my problem is controlling bandwidth of traffic flowing on the ethernet port(ex eth3) which is based from the routing made on the machine(for example i have routed 3 diferrent ip blocks to pass thru the ether). how will i set limit to traffic used per individual ip block(ex. 1st ip block limited to 1MB of traffic, 2nd ip block limited to 2MB of traffic, 3rd ip block limited to 3MB of traffic).
any links, websites, documents and knowledge you might share will be very highly appreciated..
thanks
van
Quoted 13 lines · van
to everyone,
hi people, am new with this things(advance routing/traffic control). my query is this, i will be testing out this setup. i have already bridge a 2-port ethernet
card(ex eth2, eth3), not physically assigning any ip address to this ports. the bridge was assigned with an ip instead. now, my problem is controlling bandwidth of traffic flowing on the ethernet port(ex eth3) which is based from the routing made on the machine(for example i have routed 3 diferrent ip blocks to pass thru the ether). how will i set limit to traffic used per individual ip block(ex. 1st ip block limited to 1MB of traffic, 2nd ip block limited to 2MB of traffic, 3rd ip block limited to 3MB of traffic).
Quoted 2 lines
any links, websites, documents and knowledge you might share will be very highly appreciated..
You can start with
http://lartc.org
http://docum.org
Shaping on a bridge or a router is the same. Except that you need some extra patches if you want to use iptables + fw filter on a bridge to classify packets.
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.oftc.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Van ....
You need to see http://docum.org it has good examples.
and the masters guide is at http://lartc.org
joel
Quoted 14 lines · van
to everyone,
hi people, am new with this things(advance routing/traffic control). my query is this, i will be testing out this setup.
i have already bridge a 2-port ethernetcard(ex eth2, eth3), not physically assigning any ip address to this ports. the bridge was assigned with an ip instead. now, my problem is controlling bandwidth of traffic flowing on the ethernet port(ex eth3) which is based from the routing made on the machine(for example i have routed 3 diferrent ip blocks to pass thru the ether). how will i set limit to traffic used per individual ip block(ex. 1st ip block limited to 1MB of traffic, 2nd ip block limited to 2MB of traffic, 3rd ip block limited to 3MB of traffic).
Quoted 5 lines
any links, websites, documents and knowledge you might share will be very highly appreciated..
thanks
van
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
thanks very much for the info : )
van
----- Original Message -----
From: "Stef Coene" <[email protected]>
To: "van" <[email protected]>; <[email protected]>
Sent: Friday, August 29, 2003 5:45 PM
Subject: Re: [LARTC] where do i start?
Quoted 7 lines · van
Quoted 6 lines
to everyone,
hi people, am new with this things(advance routing/traffic control). my query is this, i will be testing out this setup. i have already bridge a 2-port ethernet
card(ex eth2, eth3), not physically assigning any ip address to this ports. the bridge was assigned with an ip instead. now,
my
Quoted 1 line
Quoted 1 line
problem is controlling bandwidth of traffic flowing on the ethernet
port(ex
Quoted 2 lines
Quoted 2 lines
eth3) which is based from the routing made on the machine(for example i have routed 3 diferrent ip blocks to pass thru the ether). how will i
set
Quoted 1 line
Quoted 1 line
limit to traffic used per individual ip block(ex. 1st ip block limited
to
Quoted 4 lines
Quoted 4 lines
1MB of traffic, 2nd ip block limited to 2MB of traffic, 3rd ip block limited to 3MB of traffic).
any links, websites, documents and knowledge you might share will be
very
Quoted 6 lines
Quoted 1 line
highly appreciated..
You can start with
http://lartc.org
http://docum.orgShaping on a bridge or a router is the same. Except that you need some
extra
Quoted 13 lines
patches if you want to use iptables + fw filter on a bridge to classify packets.
Stef
--
[email protected]
"Using Linux as bandwidth manager"
http://www.docum.org/
#lartc @ irc.oftc.net
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
thanks very much for the info and the sites youv'e included. : ) . i will just buzz-in again if i get into trouble making things to work
van
----- Original Message -----
From: "Joel" <[email protected]>
To: "van" <[email protected]>
Cc: <[email protected]>
Sent: Friday, August 29, 2003 5:45 PM
Subject: Re: [LARTC] where do i start?
Quoted 31 lines
Van ....
You need to see http://docum.org it has good examples.
and the masters guide is at http://lartc.org
joel
Quoted 19 lines · van
to everyone,
hi people, am new with this things(advance routing/traffic control). my query is this, i will be testing out this setup.
i have already bridge a 2-port ethernetcard(ex eth2, eth3), not physically assigning any ip address to this ports. the bridge was assigned with an ip instead. now, my problem is controlling bandwidth of traffic flowing on the ethernet port(ex eth3) which is based from the routing made on the machine(for example i have routed 3 diferrent ip blocks to pass thru the ether). how will i set limit to traffic used per individual ip block(ex. 1st ip block limited to 1MB of traffic, 2nd ip block limited to 2MB of traffic, 3rd ip block limited to 3MB of traffic).any links, websites, documents and knowledge you might share will be very highly appreciated..
thanks
van
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/