Skip to contentSkip to conversation

where do i start?

LARTC van 3 participants 5 messages Aug 29, 2003

lore
Share & tools
lore

van

author
#0 lore raw

to everyone,

hi people, am new with this things(advance routing/traffic control). my query is this, i will be testing out this setup.
i have already bridge a 2-port ethernet card(ex eth2, eth3), not physically assigning any ip address to this ports. the bridge was assigned with an ip instead. now, my problem is controlling bandwidth of traffic flowing on the ethernet port(ex eth3) which is based from the routing made on the machine(for example i have routed 3 diferrent ip blocks to pass thru the ether). how will i set limit to traffic used per individual ip block(ex. 1st ip block limited to 1MB of traffic, 2nd ip block limited to 2MB of traffic, 3rd ip block limited to 3MB of traffic).

any links, websites, documents and knowledge you might share will be very highly appreciated..

thanks
van

#1 lore raw
Quoted 13 lines · van

to everyone,

hi people, am new with this things(advance routing/traffic control). my query is this, i will be testing out this setup. i have already bridge a 2-port ethernet card(ex eth2, eth3), not physically assigning any ip address to this ports. the bridge was assigned with an ip instead. now, my problem is controlling bandwidth of traffic flowing on the ethernet port(ex eth3) which is based from the routing made on the machine(for example i have routed 3 diferrent ip blocks to pass thru the ether). how will i set limit to traffic used per individual ip block(ex. 1st ip block limited to 1MB of traffic, 2nd ip block limited to 2MB of traffic, 3rd ip block limited to 3MB of traffic).

Quoted 2 lines

any links, websites, documents and knowledge you might share will be very highly appreciated..

You can start with
http://lartc.org
http://docum.org

Shaping on a bridge or a router is the same. Except that you need some extra patches if you want to use iptables + fw filter on a bridge to classify packets.

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.oftc.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#2 lore raw
In reply to van

Van ....

You need to see http://docum.org it has good examples.

and the masters guide is at http://lartc.org

joel

Quoted 14 lines · van

to everyone,

hi people, am new with this things(advance routing/traffic control). my query is this, i will be testing out this setup.
i have already bridge a 2-port ethernet card(ex eth2, eth3), not physically assigning any ip address to this ports. the bridge was assigned with an ip instead. now, my problem is controlling bandwidth of traffic flowing on the ethernet port(ex eth3) which is based from the routing made on the machine(for example i have routed 3 diferrent ip blocks to pass thru the ether). how will i set limit to traffic used per individual ip block(ex. 1st ip block limited to 1MB of traffic, 2nd ip block limited to 2MB of traffic, 3rd ip block limited to 3MB of traffic).

Quoted 5 lines

any links, websites, documents and knowledge you might share will be very highly appreciated..

thanks
van

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

author
#3 lore raw
In reply to van

thanks very much for the info : )

van

----- Original Message -----
From: "Stef Coene" <[email protected]>
To: "van" <[email protected]>; <[email protected]>
Sent: Friday, August 29, 2003 5:45 PM
Subject: Re: [LARTC] where do i start?

Quoted 7 lines · van
Quoted 6 lines

to everyone,

hi people, am new with this things(advance routing/traffic control). my query is this, i will be testing out this setup. i have already bridge a 2-port ethernet card(ex eth2, eth3), not physically assigning any ip address to this ports. the bridge was assigned with an ip instead. now,

my

Quoted 1 line
Quoted 1 line

problem is controlling bandwidth of traffic flowing on the ethernet

port(ex

Quoted 2 lines
Quoted 2 lines

eth3) which is based from the routing made on the machine(for example i have routed 3 diferrent ip blocks to pass thru the ether). how will i

set

Quoted 1 line
Quoted 1 line

limit to traffic used per individual ip block(ex. 1st ip block limited

to

Quoted 4 lines
Quoted 4 lines

1MB of traffic, 2nd ip block limited to 2MB of traffic, 3rd ip block limited to 3MB of traffic).

any links, websites, documents and knowledge you might share will be

very

Quoted 6 lines
Quoted 1 line

highly appreciated..

You can start with
http://lartc.org
http://docum.org

Shaping on a bridge or a router is the same. Except that you need some

extra

Quoted 13 lines

patches if you want to use iptables + fw filter on a bridge to classify packets.

Stef

--

[email protected]
"Using Linux as bandwidth manager"
http://www.docum.org/
#lartc @ irc.oftc.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

author
#4 lore raw
In reply to van

thanks very much for the info and the sites youv'e included. : ) . i will just buzz-in again if i get into trouble making things to work

van

----- Original Message -----
From: "Joel" <[email protected]>
To: "van" <[email protected]>
Cc: <[email protected]>
Sent: Friday, August 29, 2003 5:45 PM
Subject: Re: [LARTC] where do i start?

Quoted 31 lines

Van ....

You need to see http://docum.org it has good examples.

and the masters guide is at http://lartc.org

joel

Quoted 19 lines · van

to everyone,

hi people, am new with this things(advance routing/traffic control). my query is this, i will be testing out this setup.
i have already bridge a 2-port ethernet card(ex eth2, eth3), not physically assigning any ip address to this ports. the bridge was assigned with an ip instead. now, my problem is controlling bandwidth of traffic flowing on the ethernet port(ex eth3) which is based from the routing made on the machine(for example i have routed 3 diferrent ip blocks to pass thru the ether). how will i set limit to traffic used per individual ip block(ex. 1st ip block limited to 1MB of traffic, 2nd ip block limited to 2MB of traffic, 3rd ip block limited to 3MB of traffic).

any links, websites, documents and knowledge you might share will be very highly appreciated..

thanks
van

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/