Wondershaper - question
Hi,
I have a question conercing wondershaper. I'm using the Clarkconnect linux distribution for my linux router and I tried to use wondershaper.
On start up of wshaper, there are no errors or any other problems but I'm not sure if it's running correctly. Only one qdisc / one class is used and when I start an uplink ftp transfer, my ping time is growing up to 1700ms - I don't think that there is anything shaped oder scheduled.
In the wshaper file I set the up- and downlink values and for the p2p I set this:
# low priority source ports NOPRIOPORTSRCF62
# low priority destination ports NOPRIOPORTDSTF62
Then i start it:
[root@Astoria bin]# wshaper start
[root@Astoria bin]#
One or two minutes later (with p2p traffic and some pings) i got this:
[root@Astoria bin]# wshaper status
qdisc ingress ffff: ----------------
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
qdisc sfq 30: quantum 1514b perturb 10sec
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
qdisc sfq 20: quantum 1514b perturb 10sec
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
qdisc sfq 10: quantum 1514b perturb 10sec
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
qdisc cbq 1: rate 10Mbit (bounded,isolated) prio no-transmit Sent 1116535 bytes 6148 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 624 undertime 0
class cbq 1: root rate 10Mbit (bounded,isolated) prio no-transmit Sent 1117031 bytes 6154 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 624 undertime 0
class cbq 1:10 parent 1:1 leaf 10: rate 120Kbit prio 1
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 624 undertime 0
class cbq 1:1 parent 1: rate 120Kbit (bounded,isolated) prio 5
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 624 undertime 0
class cbq 1:20 parent 1:1 leaf 20: rate 108Kbit prio 2
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 624 undertime 0
class cbq 1:30 parent 1:1 leaf 30: rate 96Kbit prio 2
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 624 undertime 0
[root@Astoria bin]#
As you can see, just qdisc 1: is used. The same behavior after hours of running wshaper; only this one qdisc is used.
Has anyone an idea why this happens?
Thanks,
Matthias Lendholt
(Berlin, Germany)
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Matthias Lendholt wrote:
Those are port lists, not the line speed. They should be more like
NOPRIOPORTDST="53 21 22"
or similar. Check the docs for more help on it.
Quoted 16 lines
Hi,
I have a question conercing wondershaper. I'm using the Clarkconnect linux distribution for my linux router and I tried to use wondershaper.On start up of wshaper, there are no errors or any other problems but I'm not sure if it's running correctly. Only one qdisc / one class is used and when I start an uplink ftp transfer, my ping time is growing up to 1700ms - I don't think that there is anything shaped oder scheduled.
In the wshaper file I set the up- and downlink values and for the p2p I set this:
# low priority source ports NOPRIOPORTSRCF62# low priority destination ports NOPRIOPORTDSTF62
Signature · 5 lines
http://www.ivanhawkes.com | ICQ: 173-392-038 _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/