Skip to contentSkip to conversation

riscv: sifive_u: Improve the emulation fidelity of sifive_u machine

PATCH Superseded Bin Meng 3 participants 41 messages Aug 5, 2019 – Aug 6, 2019

Subsystems (2)

v1 of 8 Superseded Latest is v8 →

lore
Share & tools
lore

Bin Meng

author
#0 lore raw

cover riscv: sifive_u: Improve the emulation fidelity of sifive_u machine

As of today, the QEMU 'sifive_u' machine is a special target that does not boot the upstream OpenSBI/U-Boot firmware images built for the real SiFive HiFive Unleashed board. Hence OpenSBI supports a special platform "qemu/sifive_u". For U-Boot, the sifive_fu540_defconfig is referenced in the OpenSBI doc as its payload, but that does not boot at all due to various issues in current QEMU 'sifive_u' machine codes.

This series aims to improve the emulation fidelity of sifive_u machine, so that the upstream OpenSBI, U-Boot and kernel images built for the SiFive HiFive Unleashed board can be used out of the box without any special hack.

The major changes are:
- Heterogeneous harts creation supported, so that we can create a CPU that exactly mirrors the real hardware: 1 E51 + 4 U54.
- Implemented a PRCI model for FU540
- Implemented an OTP model for FU540, primarily used for storing serial number of the board
- Fixed GEM support that was seriously broken on sifive_u
- Synced device tree with upstream Linux kernel on sifive_u
- Adding initramfs loading support on sifive_u

OpenSBI v0.4 image built for sifive/fu540 is included as the default bios image for 'sifive_u' machine.

The series is tested against OpenSBI v0.4 image for sifive/fu540 paltform, U-Boot v2019.10-rc1 image for sifive_fu540_defconfig, and Linux kernel v5.3-rc3 image with the following patch:

macb: Update compatibility string for SiFive FU540-C000
https://patchwork.kernel.org/patch/11050003/

OpenSBI + U-Boot, ping/tftpboot with U-Boot MACB driver works well. For Linux, only checked boot log of MACB probe success without error.

Bin Meng (28):
riscv: hw: Remove superfluous "linux,phandle" property
riscv: hw: Use qemu_fdt_setprop_cell() for property with only 1 cell
riscv: Add a sifive_cpu.h to include both E and U cpu type defines
riscv: hart: Extract hart realize to a separate routine
riscv: hart: Support heterogeneous harts population
riscv: sifive_u: Update hart configuration to reflect the real FU540
SoC
riscv: sifive_u: Set the minimum number of cpus to 2
riscv: sifive_u: Update PLIC hart topology configuration string
riscv: sifive_u: Update UART base addresses
riscv: sifive_u: Remove the unnecessary include of prci header
riscv: sifive: Rename sifive_prci.{c,h} to sifive_e_prci.{c,h}
riscv: sifive_e: prci: Fix a typo of hfxosccfg register programming
riscv: sifive_e: prci: Update the PRCI register block size
riscv: sifive: Implement PRCI model for FU540
riscv: sifive_u: Generate hfclk and rtcclk nodes
riscv: sifive_u: Add PRCI block to the SoC
riscv: sifive_u: Change UART node name in device tree
riscv: hw: Implement a model for SiFive FU540 OTP
riscv: sifive_u: Instantiate OTP memory with a serial number
riscv: roms: Update default bios for sifive_u machine
riscv: sifive_u: Update UART and ethernet node clock properties
riscv: sifive_u: Generate an aliases node in the device tree
riscv: sifive: Move sifive_mmio_emulate() to a common place
riscv: sifive_u: Fix broken GEM support
riscv: sifive_u: Support loading initramfs
riscv: hw: Update PLIC device tree
riscv: virt: Change create_fdt() to return void
riscv: sifive_u: Update model and compatible strings in device tree

 hw/riscv/Makefile.objs                             |   4 +-
 hw/riscv/riscv_hart.c                              |  75 ++++++--
 hw/riscv/sifive_e.c                                |  12 +-
 hw/riscv/{sifive_prci.c => sifive_e_prci.c}        |  16 +-
 hw/riscv/sifive_u.c                                | 181 +++++++++++++------
 hw/riscv/sifive_u_otp.c                            | 194 +++++++++++++++++++++
 hw/riscv/sifive_u_prci.c                           | 163 +++++++++++++++++
 hw/riscv/virt.c                                    |  42 ++---
 include/hw/riscv/sifive_cpu.h                      |  39 +++++
 include/hw/riscv/sifive_e.h                        |   7 +-
 .../hw/riscv/{sifive_prci.h => sifive_e_prci.h}    |  16 +-
 include/hw/riscv/sifive_u.h                        |  15 +-
 include/hw/riscv/sifive_u_otp.h                    |  90 ++++++++++
 include/hw/riscv/sifive_u_prci.h                   | 100 +++++++++++
 pc-bios/opensbi-riscv64-sifive_u-fw_jump.bin       | Bin 40968 -> 45064 bytes
 roms/Makefile                                      |   4 +-
 16 files changed, 824 insertions(+), 134 deletions(-)
 rename hw/riscv/{sifive_prci.c => sifive_e_prci.c} (88%)
 create mode 100644 hw/riscv/sifive_u_otp.c
 create mode 100644 hw/riscv/sifive_u_prci.c
 create mode 100644 include/hw/riscv/sifive_cpu.h
 rename include/hw/riscv/{sifive_prci.h => sifive_e_prci.h} (80%)
 create mode 100644 include/hw/riscv/sifive_u_otp.h
 create mode 100644 include/hw/riscv/sifive_u_prci.h
Signature · 1 line
2.7.4
author
#1 lore raw

PATCH 1/28 riscv: hw: Remove superfluous "linux, phandle" property

"linux,phandle" property is optional. Remove all instances in the sifive_u and virt machine device tree.

---

 hw/riscv/sifive_u.c | 3 ---
 hw/riscv/virt.c     | 3 ---
 2 files changed, 6 deletions(-)
hw/riscv/sifive_u.c +0 -3
index 71b8083..ef36948 100644
@@ -125,7 +125,6 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
         qemu_fdt_setprop_string(fdt, nodename, "device_type", "cpu");
         qemu_fdt_add_subnode(fdt, intc);
         qemu_fdt_setprop_cell(fdt, intc, "phandle", cpu_phandle);
-        qemu_fdt_setprop_cell(fdt, intc, "linux,phandle", cpu_phandle);
         qemu_fdt_setprop_string(fdt, intc, "compatible", "riscv,cpu-intc");
         qemu_fdt_setprop(fdt, intc, "interrupt-controller", NULL, 0);
         qemu_fdt_setprop_cell(fdt, intc, "#interrupt-cells", 1);
@@ -184,7 +183,6 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
     qemu_fdt_setprop_cell(fdt, nodename, "riscv,max-priority", 7);
     qemu_fdt_setprop_cell(fdt, nodename, "riscv,ndev", 0x35);
     qemu_fdt_setprop_cells(fdt, nodename, "phandle", plic_phandle);
-    qemu_fdt_setprop_cells(fdt, nodename, "linux,phandle", plic_phandle);
     plic_phandle = qemu_fdt_get_phandle(fdt, nodename);
     g_free(cells);
     g_free(nodename);
@@ -197,7 +195,6 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
     qemu_fdt_setprop_cell(fdt, nodename, "clock-frequency",
         SIFIVE_U_GEM_CLOCK_FREQ);
     qemu_fdt_setprop_cell(fdt, nodename, "phandle", ethclk_phandle);
-    qemu_fdt_setprop_cell(fdt, nodename, "linux,phandle", ethclk_phandle);
     ethclk_phandle = qemu_fdt_get_phandle(fdt, nodename);
     g_free(nodename);
 
hw/riscv/virt.c +0 -3
index 25faf3b..00be05a 100644
@@ -170,11 +170,9 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
         qemu_fdt_setprop_cell(fdt, nodename, "reg", cpu);
         qemu_fdt_setprop_string(fdt, nodename, "device_type", "cpu");
         qemu_fdt_setprop_cell(fdt, nodename, "phandle", cpu_phandle);
-        qemu_fdt_setprop_cell(fdt, nodename, "linux,phandle", cpu_phandle);
         intc_phandle = phandle++;
         qemu_fdt_add_subnode(fdt, intc);
         qemu_fdt_setprop_cell(fdt, intc, "phandle", intc_phandle);
-        qemu_fdt_setprop_cell(fdt, intc, "linux,phandle", intc_phandle);
         qemu_fdt_setprop_string(fdt, intc, "compatible", "riscv,cpu-intc");
         qemu_fdt_setprop(fdt, intc, "interrupt-controller", NULL, 0);
         qemu_fdt_setprop_cell(fdt, intc, "#interrupt-cells", 1);
@@ -250,7 +248,6 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
     qemu_fdt_setprop_cell(fdt, nodename, "riscv,max-priority", 7);
     qemu_fdt_setprop_cell(fdt, nodename, "riscv,ndev", VIRTIO_NDEV);
     qemu_fdt_setprop_cells(fdt, nodename, "phandle", plic_phandle);
-    qemu_fdt_setprop_cells(fdt, nodename, "linux,phandle", plic_phandle);
     plic_phandle = qemu_fdt_get_phandle(fdt, nodename);
     g_free(cells);
     g_free(nodename);
Signature · 1 line
2.7.4
Reviewed-by on v1 1/28
#2 lore raw

Re: [Qemu-devel] [PATCH 01/28] riscv: hw: Remove superfluous "linux, phandle" property

Quoted 5 lines · Bin Meng

"linux,phandle" property is optional. Remove all instances in the sifive_u and virt machine device tree.

Alistair

Quoted 62 lines

---

 hw/riscv/sifive_u.c | 3 ---
 hw/riscv/virt.c     | 3 ---
 2 files changed, 6 deletions(-)
hw/riscv/sifive_u.c +0 -3
index 71b8083..ef36948 100644
@@ -125,7 +125,6 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
         qemu_fdt_setprop_string(fdt, nodename, "device_type", "cpu");
         qemu_fdt_add_subnode(fdt, intc);
         qemu_fdt_setprop_cell(fdt, intc, "phandle", cpu_phandle);
-        qemu_fdt_setprop_cell(fdt, intc, "linux,phandle", cpu_phandle);
         qemu_fdt_setprop_string(fdt, intc, "compatible", "riscv,cpu-intc");
         qemu_fdt_setprop(fdt, intc, "interrupt-controller", NULL, 0);
         qemu_fdt_setprop_cell(fdt, intc, "#interrupt-cells", 1);
@@ -184,7 +183,6 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
     qemu_fdt_setprop_cell(fdt, nodename, "riscv,max-priority", 7);
     qemu_fdt_setprop_cell(fdt, nodename, "riscv,ndev", 0x35);
     qemu_fdt_setprop_cells(fdt, nodename, "phandle", plic_phandle);
-    qemu_fdt_setprop_cells(fdt, nodename, "linux,phandle", plic_phandle);
     plic_phandle = qemu_fdt_get_phandle(fdt, nodename);
     g_free(cells);
     g_free(nodename);
@@ -197,7 +195,6 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
     qemu_fdt_setprop_cell(fdt, nodename, "clock-frequency",
         SIFIVE_U_GEM_CLOCK_FREQ);
     qemu_fdt_setprop_cell(fdt, nodename, "phandle", ethclk_phandle);
-    qemu_fdt_setprop_cell(fdt, nodename, "linux,phandle", ethclk_phandle);
     ethclk_phandle = qemu_fdt_get_phandle(fdt, nodename);
     g_free(nodename);
 
hw/riscv/virt.c +0 -4
index 25faf3b..00be05a 100644
@@ -170,11 +170,9 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
         qemu_fdt_setprop_cell(fdt, nodename, "reg", cpu);
         qemu_fdt_setprop_string(fdt, nodename, "device_type", "cpu");
         qemu_fdt_setprop_cell(fdt, nodename, "phandle", cpu_phandle);
-        qemu_fdt_setprop_cell(fdt, nodename, "linux,phandle", cpu_phandle);
         intc_phandle = phandle++;
         qemu_fdt_add_subnode(fdt, intc);
         qemu_fdt_setprop_cell(fdt, intc, "phandle", intc_phandle);
-        qemu_fdt_setprop_cell(fdt, intc, "linux,phandle", intc_phandle);
         qemu_fdt_setprop_string(fdt, intc, "compatible", "riscv,cpu-intc");
         qemu_fdt_setprop(fdt, intc, "interrupt-controller", NULL, 0);
         qemu_fdt_setprop_cell(fdt, intc, "#interrupt-cells", 1);
@@ -250,7 +248,6 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
     qemu_fdt_setprop_cell(fdt, nodename, "riscv,max-priority", 7);
     qemu_fdt_setprop_cell(fdt, nodename, "riscv,ndev", VIRTIO_NDEV);
     qemu_fdt_setprop_cells(fdt, nodename, "phandle", plic_phandle);
-    qemu_fdt_setprop_cells(fdt, nodename, "linux,phandle", plic_phandle);
     plic_phandle = qemu_fdt_get_phandle(fdt, nodename);
     g_free(cells);
     g_free(nodename);
--

2.7.4

author
#3 lore raw

PATCH 2/28 riscv: hw: Use qemu_fdt_setprop_cell() for property with only 1 cell

In reply to Bin Meng

Some of the properties only have 1 cell so we should use qemu_fdt_setprop_cell() instead of qemu_fdt_setprop_cells().

---

 hw/riscv/sifive_u.c | 16 ++++++++--------
 hw/riscv/virt.c     | 24 ++++++++++++------------
 2 files changed, 20 insertions(+), 20 deletions(-)
hw/riscv/sifive_u.c +8 -8
index ef36948..623ee64 100644
@@ -182,7 +182,7 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
     qemu_fdt_setprop_string(fdt, nodename, "reg-names", "control");
     qemu_fdt_setprop_cell(fdt, nodename, "riscv,max-priority", 7);
     qemu_fdt_setprop_cell(fdt, nodename, "riscv,ndev", 0x35);
-    qemu_fdt_setprop_cells(fdt, nodename, "phandle", plic_phandle);
+    qemu_fdt_setprop_cell(fdt, nodename, "phandle", plic_phandle);
     plic_phandle = qemu_fdt_get_phandle(fdt, nodename);
     g_free(cells);
     g_free(nodename);
@@ -207,20 +207,20 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
         0x0, memmap[SIFIVE_U_GEM].size);
     qemu_fdt_setprop_string(fdt, nodename, "reg-names", "control");
     qemu_fdt_setprop_string(fdt, nodename, "phy-mode", "gmii");
-    qemu_fdt_setprop_cells(fdt, nodename, "interrupt-parent", plic_phandle);
-    qemu_fdt_setprop_cells(fdt, nodename, "interrupts", SIFIVE_U_GEM_IRQ);
+    qemu_fdt_setprop_cell(fdt, nodename, "interrupt-parent", plic_phandle);
+    qemu_fdt_setprop_cell(fdt, nodename, "interrupts", SIFIVE_U_GEM_IRQ);
     qemu_fdt_setprop_cells(fdt, nodename, "clocks",
         ethclk_phandle, ethclk_phandle, ethclk_phandle);
     qemu_fdt_setprop(fdt, nodename, "clocks-names", ethclk_names,
         sizeof(ethclk_names));
-    qemu_fdt_setprop_cells(fdt, nodename, "#address-cells", 1);
-    qemu_fdt_setprop_cells(fdt, nodename, "#size-cells", 0);
+    qemu_fdt_setprop_cell(fdt, nodename, "#address-cells", 1);
+    qemu_fdt_setprop_cell(fdt, nodename, "#size-cells", 0);
     g_free(nodename);
 
     nodename = g_strdup_printf("/soc/ethernet@%lx/ethernet-phy@0",
         (long)memmap[SIFIVE_U_GEM].base);
     qemu_fdt_add_subnode(fdt, nodename);
-    qemu_fdt_setprop_cells(fdt, nodename, "reg", 0x0);
+    qemu_fdt_setprop_cell(fdt, nodename, "reg", 0x0);
     g_free(nodename);
 
     nodename = g_strdup_printf("/soc/uart@%lx",
@@ -232,8 +232,8 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
         0x0, memmap[SIFIVE_U_UART0].size);
     qemu_fdt_setprop_cell(fdt, nodename, "clock-frequency",
                           SIFIVE_U_CLOCK_FREQ / 2);
-    qemu_fdt_setprop_cells(fdt, nodename, "interrupt-parent", plic_phandle);
-    qemu_fdt_setprop_cells(fdt, nodename, "interrupts", SIFIVE_U_UART0_IRQ);
+    qemu_fdt_setprop_cell(fdt, nodename, "interrupt-parent", plic_phandle);
+    qemu_fdt_setprop_cell(fdt, nodename, "interrupts", SIFIVE_U_UART0_IRQ);
 
     qemu_fdt_add_subnode(fdt, "/chosen");
     qemu_fdt_setprop_string(fdt, "/chosen", "stdout-path", nodename);
hw/riscv/virt.c +12 -12
index 00be05a..127f005 100644
@@ -233,8 +233,8 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
     nodename = g_strdup_printf("/soc/interrupt-controller@%lx",
         (long)memmap[VIRT_PLIC].base);
     qemu_fdt_add_subnode(fdt, nodename);
-    qemu_fdt_setprop_cells(fdt, nodename, "#address-cells",
-                           FDT_PLIC_ADDR_CELLS);
+    qemu_fdt_setprop_cell(fdt, nodename, "#address-cells",
+                          FDT_PLIC_ADDR_CELLS);
     qemu_fdt_setprop_cell(fdt, nodename, "#interrupt-cells",
                           FDT_PLIC_INT_CELLS);
     qemu_fdt_setprop_string(fdt, nodename, "compatible", "riscv,plic0");
@@ -247,7 +247,7 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
     qemu_fdt_setprop_string(fdt, nodename, "reg-names", "control");
     qemu_fdt_setprop_cell(fdt, nodename, "riscv,max-priority", 7);
     qemu_fdt_setprop_cell(fdt, nodename, "riscv,ndev", VIRTIO_NDEV);
-    qemu_fdt_setprop_cells(fdt, nodename, "phandle", plic_phandle);
+    qemu_fdt_setprop_cell(fdt, nodename, "phandle", plic_phandle);
     plic_phandle = qemu_fdt_get_phandle(fdt, nodename);
     g_free(cells);
     g_free(nodename);
@@ -260,19 +260,19 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
         qemu_fdt_setprop_cells(fdt, nodename, "reg",
             0x0, memmap[VIRT_VIRTIO].base + i * memmap[VIRT_VIRTIO].size,
             0x0, memmap[VIRT_VIRTIO].size);
-        qemu_fdt_setprop_cells(fdt, nodename, "interrupt-parent", plic_phandle);
-        qemu_fdt_setprop_cells(fdt, nodename, "interrupts", VIRTIO_IRQ + i);
+        qemu_fdt_setprop_cell(fdt, nodename, "interrupt-parent", plic_phandle);
+        qemu_fdt_setprop_cell(fdt, nodename, "interrupts", VIRTIO_IRQ + i);
         g_free(nodename);
     }
 
     nodename = g_strdup_printf("/soc/pci@%lx",
         (long) memmap[VIRT_PCIE_ECAM].base);
     qemu_fdt_add_subnode(fdt, nodename);
-    qemu_fdt_setprop_cells(fdt, nodename, "#address-cells",
-                           FDT_PCI_ADDR_CELLS);
-    qemu_fdt_setprop_cells(fdt, nodename, "#interrupt-cells",
-                           FDT_PCI_INT_CELLS);
-    qemu_fdt_setprop_cells(fdt, nodename, "#size-cells", 0x2);
+    qemu_fdt_setprop_cell(fdt, nodename, "#address-cells",
+                          FDT_PCI_ADDR_CELLS);
+    qemu_fdt_setprop_cell(fdt, nodename, "#interrupt-cells",
+                          FDT_PCI_INT_CELLS);
+    qemu_fdt_setprop_cell(fdt, nodename, "#size-cells", 0x2);
     qemu_fdt_setprop_string(fdt, nodename, "compatible",
                             "pci-host-ecam-generic");
     qemu_fdt_setprop_string(fdt, nodename, "device_type", "pci");
@@ -309,8 +309,8 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
         0x0, memmap[VIRT_UART0].base,
         0x0, memmap[VIRT_UART0].size);
     qemu_fdt_setprop_cell(fdt, nodename, "clock-frequency", 3686400);
-        qemu_fdt_setprop_cells(fdt, nodename, "interrupt-parent", plic_phandle);
-        qemu_fdt_setprop_cells(fdt, nodename, "interrupts", UART0_IRQ);
+    qemu_fdt_setprop_cell(fdt, nodename, "interrupt-parent", plic_phandle);
+    qemu_fdt_setprop_cell(fdt, nodename, "interrupts", UART0_IRQ);
 
     qemu_fdt_add_subnode(fdt, "/chosen");
     qemu_fdt_setprop_string(fdt, "/chosen", "stdout-path", nodename);
Signature · 1 line
2.7.4
Reviewed-by on v1 2/28
#4 lore raw

Re: [Qemu-devel] [PATCH 02/28] riscv: hw: Use qemu_fdt_setprop_cell() for property with only 1 cell

Quoted 5 lines · Bin Meng

Some of the properties only have 1 cell so we should use qemu_fdt_setprop_cell() instead of qemu_fdt_setprop_cells().

Alistair

Quoted 122 lines

---

 hw/riscv/sifive_u.c | 16 ++++++++--------
 hw/riscv/virt.c     | 24 ++++++++++++------------
 2 files changed, 20 insertions(+), 20 deletions(-)
hw/riscv/sifive_u.c +8 -8
index ef36948..623ee64 100644
@@ -182,7 +182,7 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
     qemu_fdt_setprop_string(fdt, nodename, "reg-names", "control");
     qemu_fdt_setprop_cell(fdt, nodename, "riscv,max-priority", 7);
     qemu_fdt_setprop_cell(fdt, nodename, "riscv,ndev", 0x35);
-    qemu_fdt_setprop_cells(fdt, nodename, "phandle", plic_phandle);
+    qemu_fdt_setprop_cell(fdt, nodename, "phandle", plic_phandle);
     plic_phandle = qemu_fdt_get_phandle(fdt, nodename);
     g_free(cells);
     g_free(nodename);
@@ -207,20 +207,20 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
         0x0, memmap[SIFIVE_U_GEM].size);
     qemu_fdt_setprop_string(fdt, nodename, "reg-names", "control");
     qemu_fdt_setprop_string(fdt, nodename, "phy-mode", "gmii");
-    qemu_fdt_setprop_cells(fdt, nodename, "interrupt-parent", plic_phandle);
-    qemu_fdt_setprop_cells(fdt, nodename, "interrupts", SIFIVE_U_GEM_IRQ);
+    qemu_fdt_setprop_cell(fdt, nodename, "interrupt-parent", plic_phandle);
+    qemu_fdt_setprop_cell(fdt, nodename, "interrupts", SIFIVE_U_GEM_IRQ);
     qemu_fdt_setprop_cells(fdt, nodename, "clocks",
         ethclk_phandle, ethclk_phandle, ethclk_phandle);
     qemu_fdt_setprop(fdt, nodename, "clocks-names", ethclk_names,
         sizeof(ethclk_names));
-    qemu_fdt_setprop_cells(fdt, nodename, "#address-cells", 1);
-    qemu_fdt_setprop_cells(fdt, nodename, "#size-cells", 0);
+    qemu_fdt_setprop_cell(fdt, nodename, "#address-cells", 1);
+    qemu_fdt_setprop_cell(fdt, nodename, "#size-cells", 0);
     g_free(nodename);
 
     nodename = g_strdup_printf("/soc/ethernet@%lx/ethernet-phy@0",
         (long)memmap[SIFIVE_U_GEM].base);
     qemu_fdt_add_subnode(fdt, nodename);
-    qemu_fdt_setprop_cells(fdt, nodename, "reg", 0x0);
+    qemu_fdt_setprop_cell(fdt, nodename, "reg", 0x0);
     g_free(nodename);
 
     nodename = g_strdup_printf("/soc/uart@%lx",
@@ -232,8 +232,8 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
         0x0, memmap[SIFIVE_U_UART0].size);
     qemu_fdt_setprop_cell(fdt, nodename, "clock-frequency",
                           SIFIVE_U_CLOCK_FREQ / 2);
-    qemu_fdt_setprop_cells(fdt, nodename, "interrupt-parent", plic_phandle);
-    qemu_fdt_setprop_cells(fdt, nodename, "interrupts", SIFIVE_U_UART0_IRQ);
+    qemu_fdt_setprop_cell(fdt, nodename, "interrupt-parent", plic_phandle);
+    qemu_fdt_setprop_cell(fdt, nodename, "interrupts", SIFIVE_U_UART0_IRQ);
 
     qemu_fdt_add_subnode(fdt, "/chosen");
     qemu_fdt_setprop_string(fdt, "/chosen", "stdout-path", nodename);
hw/riscv/virt.c +12 -13
index 00be05a..127f005 100644
@@ -233,8 +233,8 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
     nodename = g_strdup_printf("/soc/interrupt-controller@%lx",
         (long)memmap[VIRT_PLIC].base);
     qemu_fdt_add_subnode(fdt, nodename);
-    qemu_fdt_setprop_cells(fdt, nodename, "#address-cells",
-                           FDT_PLIC_ADDR_CELLS);
+    qemu_fdt_setprop_cell(fdt, nodename, "#address-cells",
+                          FDT_PLIC_ADDR_CELLS);
     qemu_fdt_setprop_cell(fdt, nodename, "#interrupt-cells",
                           FDT_PLIC_INT_CELLS);
     qemu_fdt_setprop_string(fdt, nodename, "compatible", "riscv,plic0");
@@ -247,7 +247,7 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
     qemu_fdt_setprop_string(fdt, nodename, "reg-names", "control");
     qemu_fdt_setprop_cell(fdt, nodename, "riscv,max-priority", 7);
     qemu_fdt_setprop_cell(fdt, nodename, "riscv,ndev", VIRTIO_NDEV);
-    qemu_fdt_setprop_cells(fdt, nodename, "phandle", plic_phandle);
+    qemu_fdt_setprop_cell(fdt, nodename, "phandle", plic_phandle);
     plic_phandle = qemu_fdt_get_phandle(fdt, nodename);
     g_free(cells);
     g_free(nodename);
@@ -260,19 +260,19 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
         qemu_fdt_setprop_cells(fdt, nodename, "reg",
             0x0, memmap[VIRT_VIRTIO].base + i * memmap[VIRT_VIRTIO].size,
             0x0, memmap[VIRT_VIRTIO].size);
-        qemu_fdt_setprop_cells(fdt, nodename, "interrupt-parent", plic_phandle);
-        qemu_fdt_setprop_cells(fdt, nodename, "interrupts", VIRTIO_IRQ + i);
+        qemu_fdt_setprop_cell(fdt, nodename, "interrupt-parent", plic_phandle);
+        qemu_fdt_setprop_cell(fdt, nodename, "interrupts", VIRTIO_IRQ + i);
         g_free(nodename);
     }
 
     nodename = g_strdup_printf("/soc/pci@%lx",
         (long) memmap[VIRT_PCIE_ECAM].base);
     qemu_fdt_add_subnode(fdt, nodename);
-    qemu_fdt_setprop_cells(fdt, nodename, "#address-cells",
-                           FDT_PCI_ADDR_CELLS);
-    qemu_fdt_setprop_cells(fdt, nodename, "#interrupt-cells",
-                           FDT_PCI_INT_CELLS);
-    qemu_fdt_setprop_cells(fdt, nodename, "#size-cells", 0x2);
+    qemu_fdt_setprop_cell(fdt, nodename, "#address-cells",
+                          FDT_PCI_ADDR_CELLS);
+    qemu_fdt_setprop_cell(fdt, nodename, "#interrupt-cells",
+                          FDT_PCI_INT_CELLS);
+    qemu_fdt_setprop_cell(fdt, nodename, "#size-cells", 0x2);
     qemu_fdt_setprop_string(fdt, nodename, "compatible",
                             "pci-host-ecam-generic");
     qemu_fdt_setprop_string(fdt, nodename, "device_type", "pci");
@@ -309,8 +309,8 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
         0x0, memmap[VIRT_UART0].base,
         0x0, memmap[VIRT_UART0].size);
     qemu_fdt_setprop_cell(fdt, nodename, "clock-frequency", 3686400);
-        qemu_fdt_setprop_cells(fdt, nodename, "interrupt-parent", plic_phandle);
-        qemu_fdt_setprop_cells(fdt, nodename, "interrupts", UART0_IRQ);
+    qemu_fdt_setprop_cell(fdt, nodename, "interrupt-parent", plic_phandle);
+    qemu_fdt_setprop_cell(fdt, nodename, "interrupts", UART0_IRQ);
 
     qemu_fdt_add_subnode(fdt, "/chosen");
     qemu_fdt_setprop_string(fdt, "/chosen", "stdout-path", nodename);
--

2.7.4

author
#5 lore raw

PATCH 3/28 riscv: Add a sifive_cpu.h to include both E and U cpu type defines

In reply to Bin Meng

Group SiFive E and U cpu type defines into one header file.

---

 include/hw/riscv/sifive_cpu.h | 31 +++++++++++++++++++++++++++++++
 include/hw/riscv/sifive_e.h   |  7 +------
 include/hw/riscv/sifive_u.h   |  7 +------
 3 files changed, 33 insertions(+), 12 deletions(-)
 create mode 100644 include/hw/riscv/sifive_cpu.h
include/hw/riscv/sifive_cpu.h new file +31 -0
new file mode 100644
index 0000000..1367996
@@ -0,0 +1,31 @@
+/*
+ * SiFive CPU types
+ *
+ * Copyright (c) 2017 SiFive, Inc.
+ * Copyright (c) 2019 Bin Meng <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2 or later, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef HW_SIFIVE_CPU_H
+#define HW_SIFIVE_CPU_H
+
+#if defined(TARGET_RISCV32)
+#define SIFIVE_E_CPU TYPE_RISCV_CPU_SIFIVE_E31
+#define SIFIVE_U_CPU TYPE_RISCV_CPU_SIFIVE_U34
+#elif defined(TARGET_RISCV64)
+#define SIFIVE_E_CPU TYPE_RISCV_CPU_SIFIVE_E51
+#define SIFIVE_U_CPU TYPE_RISCV_CPU_SIFIVE_U54
+#endif
+
+#endif /* HW_SIFIVE_CPU_H */
include/hw/riscv/sifive_e.h +1 -6
index d175b24..e17cdfd 100644
@@ -19,6 +19,7 @@
 #ifndef HW_SIFIVE_E_H
 #define HW_SIFIVE_E_H
 
+#include "hw/riscv/sifive_cpu.h"
 #include "hw/riscv/sifive_gpio.h"
 
 #define TYPE_RISCV_E_SOC "riscv.sifive.e.soc"
@@ -83,10 +84,4 @@ enum {
 #define SIFIVE_E_PLIC_CONTEXT_BASE 0x200000
 #define SIFIVE_E_PLIC_CONTEXT_STRIDE 0x1000
 
-#if defined(TARGET_RISCV32)
-#define SIFIVE_E_CPU TYPE_RISCV_CPU_SIFIVE_E31
-#elif defined(TARGET_RISCV64)
-#define SIFIVE_E_CPU TYPE_RISCV_CPU_SIFIVE_E51
-#endif
-
 #endif
include/hw/riscv/sifive_u.h +1 -6
index 892f0ee..4abc621 100644
@@ -20,6 +20,7 @@
 #define HW_SIFIVE_U_H
 
 #include "hw/net/cadence_gem.h"
+#include "hw/riscv/sifive_cpu.h"
 
 #define TYPE_RISCV_U_SOC "riscv.sifive.u.soc"
 #define RISCV_U_SOC(obj) \
@@ -77,10 +78,4 @@ enum {
 #define SIFIVE_U_PLIC_CONTEXT_BASE 0x200000
 #define SIFIVE_U_PLIC_CONTEXT_STRIDE 0x1000
 
-#if defined(TARGET_RISCV32)
-#define SIFIVE_U_CPU TYPE_RISCV_CPU_SIFIVE_U34
-#elif defined(TARGET_RISCV64)
-#define SIFIVE_U_CPU TYPE_RISCV_CPU_SIFIVE_U54
-#endif
-
 #endif
Signature · 1 line
2.7.4
Reviewed-by on v1 3/28
#6 lore raw

Re: [Qemu-devel] [PATCH 03/28] riscv: Add a sifive_cpu.h to include both E and U cpu type defines

Quoted 4 lines · Bin Meng

Group SiFive E and U cpu type defines into one header file.

Alistair

Quoted 95 lines

---

 include/hw/riscv/sifive_cpu.h | 31 +++++++++++++++++++++++++++++++
 include/hw/riscv/sifive_e.h   |  7 +------
 include/hw/riscv/sifive_u.h   |  7 +------
 3 files changed, 33 insertions(+), 12 deletions(-)
 create mode 100644 include/hw/riscv/sifive_cpu.h
include/hw/riscv/sifive_cpu.h new file +31 -0
new file mode 100644
index 0000000..1367996
@@ -0,0 +1,31 @@
+/*
+ * SiFive CPU types
+ *
+ * Copyright (c) 2017 SiFive, Inc.
+ * Copyright (c) 2019 Bin Meng <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2 or later, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef HW_SIFIVE_CPU_H
+#define HW_SIFIVE_CPU_H
+
+#if defined(TARGET_RISCV32)
+#define SIFIVE_E_CPU TYPE_RISCV_CPU_SIFIVE_E31
+#define SIFIVE_U_CPU TYPE_RISCV_CPU_SIFIVE_U34
+#elif defined(TARGET_RISCV64)
+#define SIFIVE_E_CPU TYPE_RISCV_CPU_SIFIVE_E51
+#define SIFIVE_U_CPU TYPE_RISCV_CPU_SIFIVE_U54
+#endif
+
+#endif /* HW_SIFIVE_CPU_H */
include/hw/riscv/sifive_e.h +1 -6
index d175b24..e17cdfd 100644
@@ -19,6 +19,7 @@
 #ifndef HW_SIFIVE_E_H
 #define HW_SIFIVE_E_H
 
+#include "hw/riscv/sifive_cpu.h"
 #include "hw/riscv/sifive_gpio.h"
 
 #define TYPE_RISCV_E_SOC "riscv.sifive.e.soc"
@@ -83,10 +84,4 @@ enum {
 #define SIFIVE_E_PLIC_CONTEXT_BASE 0x200000
 #define SIFIVE_E_PLIC_CONTEXT_STRIDE 0x1000
 
-#if defined(TARGET_RISCV32)
-#define SIFIVE_E_CPU TYPE_RISCV_CPU_SIFIVE_E31
-#elif defined(TARGET_RISCV64)
-#define SIFIVE_E_CPU TYPE_RISCV_CPU_SIFIVE_E51
-#endif
-
 #endif
include/hw/riscv/sifive_u.h +1 -7
index 892f0ee..4abc621 100644
@@ -20,6 +20,7 @@
 #define HW_SIFIVE_U_H
 
 #include "hw/net/cadence_gem.h"
+#include "hw/riscv/sifive_cpu.h"
 
 #define TYPE_RISCV_U_SOC "riscv.sifive.u.soc"
 #define RISCV_U_SOC(obj) \
@@ -77,10 +78,4 @@ enum {
 #define SIFIVE_U_PLIC_CONTEXT_BASE 0x200000
 #define SIFIVE_U_PLIC_CONTEXT_STRIDE 0x1000
 
-#if defined(TARGET_RISCV32)
-#define SIFIVE_U_CPU TYPE_RISCV_CPU_SIFIVE_U34
-#elif defined(TARGET_RISCV64)
-#define SIFIVE_U_CPU TYPE_RISCV_CPU_SIFIVE_U54
-#endif
-
 #endif
--

2.7.4

author
#7 lore raw

PATCH 4/28 riscv: hart: Extract hart realize to a separate routine

In reply to Bin Meng

Currently riscv_harts_realize() creates all harts based on the same cpu type given in the hart array property. With current implementation it can only create symmetric harts. Exact the hart realize to a separate routine in preparation for supporting heterogeneous hart arrays.

---

 hw/riscv/riscv_hart.c | 31 +++++++++++++++++++------------
 1 file changed, 19 insertions(+), 12 deletions(-)
hw/riscv/riscv_hart.c +19 -12
index ca69a1b..3dd1c6a 100644
@@ -37,26 +37,33 @@ static void riscv_harts_cpu_reset(void *opaque)
     cpu_reset(CPU(cpu));
 }
 
+static void riscv_hart_realize(RISCVHartArrayState *s, int hart,
+                               char *cpu_type, Error **errp)
+{
+    Error *err = NULL;
+
+    object_initialize_child(OBJECT(s), "harts[*]", &s->harts[hart],
+                            sizeof(RISCVCPU), cpu_type,
+                            &error_abort, NULL);
+    s->harts[hart].env.mhartid = hart;
+    qemu_register_reset(riscv_harts_cpu_reset, &s->harts[hart]);
+    object_property_set_bool(OBJECT(&s->harts[hart]), true,
+                             "realized", &err);
+    if (err) {
+        error_propagate(errp, err);
+        return;
+    }
+}
+
 static void riscv_harts_realize(DeviceState *dev, Error **errp)
 {
     RISCVHartArrayState *s = RISCV_HART_ARRAY(dev);
-    Error *err = NULL;
     int n;
 
     s->harts = g_new0(RISCVCPU, s->num_harts);
 
     for (n = 0; n < s->num_harts; n++) {
-        object_initialize_child(OBJECT(s), "harts[*]", &s->harts[n],
-                                sizeof(RISCVCPU), s->cpu_type,
-                                &error_abort, NULL);
-        s->harts[n].env.mhartid = n;
-        qemu_register_reset(riscv_harts_cpu_reset, &s->harts[n]);
-        object_property_set_bool(OBJECT(&s->harts[n]), true,
-                                 "realized", &err);
-        if (err) {
-            error_propagate(errp, err);
-            return;
-        }
+        riscv_hart_realize(s, n, s->cpu_type, errp);
     }
 }
 
Signature · 1 line
2.7.4
author
#8 lore raw

PATCH 5/28 riscv: hart: Support heterogeneous harts population

In reply to Bin Meng

At present we only allow symmetric harts to be created. In order to support heterogeneous harts like SiFive FU540, update hart array's "cpu-type" property to allow cpu type to be set per hart, separated by delimiter ",". The frist cpu type before the delimiter is assigned to hart 0, and the second cpu type before delimiter is assigned to hart 1, and so on.

If the total number of cpu types supplied in "cpu-type" property is less than number of maximum harts, the last cpu type in the property will be used to populate remaining harts.

---

 hw/riscv/riscv_hart.c | 48 +++++++++++++++++++++++++++++++++++++++++++++---
 1 file changed, 45 insertions(+), 3 deletions(-)
hw/riscv/riscv_hart.c +45 -3
index 3dd1c6a..27093e0 100644
@@ -58,13 +58,55 @@ static void riscv_hart_realize(RISCVHartArrayState *s, int hart,
 static void riscv_harts_realize(DeviceState *dev, Error **errp)
 {
     RISCVHartArrayState *s = RISCV_HART_ARRAY(dev);
-    int n;
+    char *cpu_types;
+    char *first_type, *last_type, *tmp_type;
+    int n = 0;
 
     s->harts = g_new0(RISCVCPU, s->num_harts);
 
-    for (n = 0; n < s->num_harts; n++) {
-        riscv_hart_realize(s, n, s->cpu_type, errp);
+    /* we should not touch the original s->cpu_type */
+    cpu_types = g_strdup(s->cpu_type);
+
+    /*
+     * Expect s->cpu_type property was initialized this way:
+     *
+     * "cpu-type-a": symmetric harts
+     * "cpu-type-a,cpu-type-b,cpu-type-c": heterogeneous harts
+     *
+     * For heterogeneous harts, hart cpu types are separated by delimiter ",".
+     * The frist cpu type before the delimiter is assigned to hart 0, and the
+     * second cpu type before delimiter is assigned to hart 1, and so on.
+     *
+     * If the total number of cpu types is less than s->num_harts, the last
+     * cpu type in s->cpu_type will be used to populate remaining harts.
+     */
+
+    first_type = strtok(cpu_types, ",");
+    riscv_hart_realize(s, n++, first_type, errp);
+    tmp_type = strtok(NULL, ",");
+    if (!tmp_type) {
+        /* symmetric harts */
+        for (; n < s->num_harts; n++) {
+            riscv_hart_realize(s, n, first_type, errp);
+       }
+    } else {
+        /* heterogeneous harts */
+        while (tmp_type) {
+            if (n >= s->num_harts) {
+                break;
+            }
+            riscv_hart_realize(s, n++, tmp_type, errp);
+            last_type = tmp_type;
+            tmp_type = strtok(NULL, ",");
+        }
+
+        /* populate remaining harts using the last cpu type in s->cpu_type */
+        for (; n < s->num_harts; n++) {
+            riscv_hart_realize(s, n, last_type, errp);
+        }
     }
+
+    g_free(cpu_types);
 }
 
 static void riscv_harts_class_init(ObjectClass *klass, void *data)
Signature · 1 line
2.7.4
author
#9 lore raw

PATCH 6/28 riscv: sifive_u: Update hart configuration to reflect the real FU540 SoC

In reply to Bin Meng

The FU540-C000 includes a 64-bit E51 RISC-V core and four 64-bit U54 RISC-V cores. Currently the sifive_u machine only populates 4 U54 cores. Update the max cpu number to 5 to reflect the real hardware, and pass "cpu-type" to populate heterogeneous harts.

The cpu nodes in the generated DTS have been updated as well.

---

 hw/riscv/sifive_u.c | 37 +++++++++++++++++++++++++++----------
 1 file changed, 27 insertions(+), 10 deletions(-)
hw/riscv/sifive_u.c +27 -10
index 623ee64..08d406f 100644
@@ -10,7 +10,7 @@
  * 1) CLINT (Core Level Interruptor)
  * 2) PLIC (Platform Level Interrupt Controller)
  *
- * This board currently uses a hardcoded devicetree that indicates one hart.
+ * This board currently uses a hardcoded devicetree that indicates five harts.
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms and conditions of the GNU General Public License,
@@ -26,6 +26,7 @@
  */
 
 #include "qemu/osdep.h"
+#include "qemu/cutils.h"
 #include "qemu/log.h"
 #include "qemu/error-report.h"
 #include "qapi/error.h"
@@ -117,7 +118,10 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
         qemu_fdt_add_subnode(fdt, nodename);
         qemu_fdt_setprop_cell(fdt, nodename, "clock-frequency",
                               SIFIVE_U_CLOCK_FREQ);
-        qemu_fdt_setprop_string(fdt, nodename, "mmu-type", "riscv,sv48");
+        /* cpu 0 is the management hart that does not have mmu */
+        if (cpu != 0) {
+            qemu_fdt_setprop_string(fdt, nodename, "mmu-type", "riscv,sv48");
+        }
         qemu_fdt_setprop_string(fdt, nodename, "riscv,isa", isa);
         qemu_fdt_setprop_string(fdt, nodename, "compatible", "riscv");
         qemu_fdt_setprop_string(fdt, nodename, "status", "okay");
@@ -157,15 +161,21 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
     g_free(nodename);
 
     plic_phandle = phandle++;
-    cells =  g_new0(uint32_t, s->soc.cpus.num_harts * 4);
+    cells =  g_new0(uint32_t, s->soc.cpus.num_harts * 4 - 2);
     for (cpu = 0; cpu < s->soc.cpus.num_harts; cpu++) {
         nodename =
             g_strdup_printf("/cpus/cpu@%d/interrupt-controller", cpu);
         uint32_t intc_phandle = qemu_fdt_get_phandle(fdt, nodename);
-        cells[cpu * 4 + 0] = cpu_to_be32(intc_phandle);
-        cells[cpu * 4 + 1] = cpu_to_be32(IRQ_M_EXT);
-        cells[cpu * 4 + 2] = cpu_to_be32(intc_phandle);
-        cells[cpu * 4 + 3] = cpu_to_be32(IRQ_S_EXT);
+        /* cpu 0 is the management hart that does not have S-mode */
+        if (cpu == 0) {
+            cells[0] = cpu_to_be32(intc_phandle);
+            cells[1] = cpu_to_be32(IRQ_M_EXT);
+        } else {
+            cells[cpu * 4 - 2] = cpu_to_be32(intc_phandle);
+            cells[cpu * 4 - 1] = cpu_to_be32(IRQ_M_EXT);
+            cells[cpu * 4 + 0] = cpu_to_be32(intc_phandle);
+            cells[cpu * 4 + 1] = cpu_to_be32(IRQ_S_EXT);
+        }
         g_free(nodename);
     }
     nodename = g_strdup_printf("/soc/interrupt-controller@%lx",
@@ -315,10 +325,16 @@ static void riscv_sifive_u_soc_init(Object *obj)
 {
     MachineState *ms = MACHINE(qdev_get_machine());
     SiFiveUSoCState *s = RISCV_U_SOC(obj);
+    char cpu_type[64];
+
+    /* create cpu type representing SiFive FU540 SoC */
+    pstrcpy(cpu_type, sizeof(cpu_type), SIFIVE_E_CPU);
+    pstrcat(cpu_type, sizeof(cpu_type), ",");
+    pstrcat(cpu_type, sizeof(cpu_type), SIFIVE_U_CPU);
 
     object_initialize_child(obj, "cpus", &s->cpus, sizeof(s->cpus),
                             TYPE_RISCV_HART_ARRAY, &error_abort, NULL);
-    object_property_set_str(OBJECT(&s->cpus), SIFIVE_U_CPU, "cpu-type",
+    object_property_set_str(OBJECT(&s->cpus), cpu_type, "cpu-type",
                             &error_abort);
     object_property_set_int(OBJECT(&s->cpus), ms->smp.cpus, "num-harts",
                             &error_abort);
@@ -407,10 +423,11 @@ static void riscv_sifive_u_machine_init(MachineClass *mc)
 {
     mc->desc = "RISC-V Board compatible with SiFive U SDK";
     mc->init = riscv_sifive_u_init;
-    /* The real hardware has 5 CPUs, but one of them is a small embedded power
+    /*
+     * The real hardware has 5 CPUs, but one of them is a small embedded power
      * management CPU.
      */
-    mc->max_cpus = 4;
+    mc->max_cpus = 5;
 }
 
 DEFINE_MACHINE("sifive_u", riscv_sifive_u_machine_init)
Signature · 1 line
2.7.4
author
#10 lore raw

PATCH 7/28 riscv: sifive_u: Set the minimum number of cpus to 2

In reply to Bin Meng

It is not useful if we only have one management CPU.

---

 hw/riscv/sifive_u.c | 2 ++
 1 file changed, 2 insertions(+)
hw/riscv/sifive_u.c +2 -0
index 08d406f..206eccc 100644
@@ -428,6 +428,8 @@ static void riscv_sifive_u_machine_init(MachineClass *mc)
      * management CPU.
      */
     mc->max_cpus = 5;
+    /* It is not useful if we only have one management CPU */
+    mc->min_cpus = 2;
 }
 
 DEFINE_MACHINE("sifive_u", riscv_sifive_u_machine_init)
Signature · 1 line
2.7.4
#11 lore raw

Re: [Qemu-devel] [Qemu-riscv] [PATCH 07/28] riscv: sifive_u: Set the minimum number of cpus to 2

I'm not familiar with QEMU conventions on this, but would it make sense to require having exactly 5 CPUs to match the real board?

Jonathan

Quoted 27 lines · Bin Meng

It is not useful if we only have one management CPU.

---

 hw/riscv/sifive_u.c | 2 ++
 1 file changed, 2 insertions(+)
hw/riscv/sifive_u.c +2 -0
index 08d406f..206eccc 100644
@@ -428,6 +428,8 @@ static void riscv_sifive_u_machine_init(MachineClass
 *mc)
      * management CPU.
      */
     mc->max_cpus = 5;
+    /* It is not useful if we only have one management CPU */
+    mc->min_cpus = 2;
 }
 

DEFINE_MACHINE("sifive_u", riscv_sifive_u_machine_init)
--
2.7.4

#12 lore raw

Re: [Qemu-devel] [Qemu-riscv] [PATCH 07/28] riscv: sifive_u: Set the minimum number of cpus to 2

Quoted 3 lines · Jonathan Behrens

I'm not familiar with QEMU conventions on this, but would it make sense to require having exactly 5 CPUs to match the real board?

SMP can sometimes cause failures, so I think it makes some sense to keep the default low.

Alistair

Quoted 33 lines

Jonathan

Quoted 27 lines · Bin Meng

It is not useful if we only have one management CPU.

---

 hw/riscv/sifive_u.c | 2 ++
 1 file changed, 2 insertions(+)
hw/riscv/sifive_u.c +2 -0
index 08d406f..206eccc 100644
@@ -428,6 +428,8 @@ static void riscv_sifive_u_machine_init(MachineClass
 *mc)
      * management CPU.
      */
     mc->max_cpus = 5;
+    /* It is not useful if we only have one management CPU */
+    mc->min_cpus = 2;
 }
 

DEFINE_MACHINE("sifive_u", riscv_sifive_u_machine_init)
--
2.7.4

author
#13 lore raw

PATCH 8/28 riscv: sifive_u: Update PLIC hart topology configuration string

In reply to Bin Meng

With heterogeneous harts config, the PLIC hart topology configuration string are "M,MS,.." because of the monitor hart #0.

---

 hw/riscv/sifive_u.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
hw/riscv/sifive_u.c +4 -3
index 206eccc..b235f29 100644
@@ -372,10 +372,11 @@ static void riscv_sifive_u_soc_realize(DeviceState *dev, Error **errp)
     plic_hart_config = g_malloc0(plic_hart_config_len);
     for (i = 0; i < ms->smp.cpus; i++) {
         if (i != 0) {
-            strncat(plic_hart_config, ",", plic_hart_config_len);
+            strncat(plic_hart_config, "," SIFIVE_U_PLIC_HART_CONFIG,
+                    plic_hart_config_len);
+        } else {
+            strncat(plic_hart_config, "M", plic_hart_config_len);
         }
-        strncat(plic_hart_config, SIFIVE_U_PLIC_HART_CONFIG,
-                plic_hart_config_len);
         plic_hart_config_len -= (strlen(SIFIVE_U_PLIC_HART_CONFIG) + 1);
     }
 
Signature · 1 line
2.7.4
Reviewed-by on v1 8/28
#14 lore raw

Re: [Qemu-devel] [PATCH 08/28] riscv: sifive_u: Update PLIC hart topology configuration string

Quoted 6 lines · Bin Meng

With heterogeneous harts config, the PLIC hart topology configuration string are "M,MS,.." because of the monitor hart #0.

Alistair

Quoted 28 lines

---

 hw/riscv/sifive_u.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
hw/riscv/sifive_u.c +4 -4
index 206eccc..b235f29 100644
@@ -372,10 +372,11 @@ static void riscv_sifive_u_soc_realize(DeviceState *dev, Error **errp)
     plic_hart_config = g_malloc0(plic_hart_config_len);
     for (i = 0; i < ms->smp.cpus; i++) {
         if (i != 0) {
-            strncat(plic_hart_config, ",", plic_hart_config_len);
+            strncat(plic_hart_config, "," SIFIVE_U_PLIC_HART_CONFIG,
+                    plic_hart_config_len);
+        } else {
+            strncat(plic_hart_config, "M", plic_hart_config_len);
         }
-        strncat(plic_hart_config, SIFIVE_U_PLIC_HART_CONFIG,
-                plic_hart_config_len);
         plic_hart_config_len -= (strlen(SIFIVE_U_PLIC_HART_CONFIG) + 1);
     }
 
--

2.7.4

author
#15 lore raw

PATCH 9/28 riscv: sifive_u: Update UART base addresses

In reply to Bin Meng

This updates the UART base address to match the hardware.

---

 hw/riscv/sifive_u.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
hw/riscv/sifive_u.c +2 -2
index b235f29..9f05e09 100644
@@ -60,8 +60,8 @@ static const struct MemmapEntry {
     [SIFIVE_U_MROM] =     {     0x1000,    0x11000 },
     [SIFIVE_U_CLINT] =    {  0x2000000,    0x10000 },
     [SIFIVE_U_PLIC] =     {  0xc000000,  0x4000000 },
-    [SIFIVE_U_UART0] =    { 0x10013000,     0x1000 },
-    [SIFIVE_U_UART1] =    { 0x10023000,     0x1000 },
+    [SIFIVE_U_UART0] =    { 0x10010000,     0x1000 },
+    [SIFIVE_U_UART1] =    { 0x10011000,     0x1000 },
     [SIFIVE_U_DRAM] =     { 0x80000000,        0x0 },
     [SIFIVE_U_GEM] =      { 0x100900FC,     0x2000 },
 };
Signature · 1 line
2.7.4
Reviewed-by on v1 9/28
#16 lore raw

Re: [Qemu-devel] [Qemu-riscv] [PATCH 09/28] riscv: sifive_u: Update UART base addresses

Quoted 28 lines · Bin Meng

This updates the UART base address to match the hardware.

---

 hw/riscv/sifive_u.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
hw/riscv/sifive_u.c +2 -3
index b235f29..9f05e09 100644
@@ -60,8 +60,8 @@ static const struct MemmapEntry {
     [SIFIVE_U_MROM] =     {     0x1000,    0x11000 },
     [SIFIVE_U_CLINT] =    {  0x2000000,    0x10000 },
     [SIFIVE_U_PLIC] =     {  0xc000000,  0x4000000 },
-    [SIFIVE_U_UART0] =    { 0x10013000,     0x1000 },
-    [SIFIVE_U_UART1] =    { 0x10023000,     0x1000 },
+    [SIFIVE_U_UART0] =    { 0x10010000,     0x1000 },
+    [SIFIVE_U_UART1] =    { 0x10011000,     0x1000 },
     [SIFIVE_U_DRAM] =     { 0x80000000,        0x0 },
     [SIFIVE_U_GEM] =      { 0x100900FC,     0x2000 },
 };
--

2.7.4

Acked-by on v1 9/28
#17 lore raw

Re: [Qemu-devel] [PATCH 09/28] riscv: sifive_u: Update UART base addresses

In reply to Bin Meng
Quoted 4 lines · Bin Meng

This updates the UART base address to match the hardware.

Alistair

Quoted 24 lines

---

 hw/riscv/sifive_u.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
hw/riscv/sifive_u.c +2 -3
index b235f29..9f05e09 100644
@@ -60,8 +60,8 @@ static const struct MemmapEntry {
     [SIFIVE_U_MROM] =     {     0x1000,    0x11000 },
     [SIFIVE_U_CLINT] =    {  0x2000000,    0x10000 },
     [SIFIVE_U_PLIC] =     {  0xc000000,  0x4000000 },
-    [SIFIVE_U_UART0] =    { 0x10013000,     0x1000 },
-    [SIFIVE_U_UART1] =    { 0x10023000,     0x1000 },
+    [SIFIVE_U_UART0] =    { 0x10010000,     0x1000 },
+    [SIFIVE_U_UART1] =    { 0x10011000,     0x1000 },
     [SIFIVE_U_DRAM] =     { 0x80000000,        0x0 },
     [SIFIVE_U_GEM] =      { 0x100900FC,     0x2000 },
 };
--

2.7.4

author
#18 lore raw

PATCH 10/28 riscv: sifive_u: Remove the unnecessary include of prci header

In reply to Bin Meng

sifive_u machine does not use PRCI as of today. Remove the prci header inclusion.

---

 hw/riscv/sifive_u.c | 1 -
 1 file changed, 1 deletion(-)
hw/riscv/sifive_u.c +0 -1
index 9f05e09..dfcb525 100644
@@ -40,7 +40,6 @@
 #include "hw/riscv/sifive_plic.h"
 #include "hw/riscv/sifive_clint.h"
 #include "hw/riscv/sifive_uart.h"
-#include "hw/riscv/sifive_prci.h"
 #include "hw/riscv/sifive_u.h"
 #include "hw/riscv/boot.h"
 #include "chardev/char.h"
Signature · 1 line
2.7.4
Reviewed-by on v1 10/28
#19 lore raw

Re: [Qemu-devel] [PATCH 10/28] riscv: sifive_u: Remove the unnecessary include of prci header

Quoted 5 lines · Bin Meng

sifive_u machine does not use PRCI as of today. Remove the prci header inclusion.

Alistair

Quoted 21 lines

---

 hw/riscv/sifive_u.c | 1 -
 1 file changed, 1 deletion(-)
hw/riscv/sifive_u.c +0 -2
index 9f05e09..dfcb525 100644
@@ -40,7 +40,6 @@
 #include "hw/riscv/sifive_plic.h"
 #include "hw/riscv/sifive_clint.h"
 #include "hw/riscv/sifive_uart.h"
-#include "hw/riscv/sifive_prci.h"
 #include "hw/riscv/sifive_u.h"
 #include "hw/riscv/boot.h"
 #include "chardev/char.h"
--

2.7.4

author
#20 lore raw

PATCH 11/28 riscv: sifive: Rename sifive_prci.{c, h} to sifive_e_prci.{c, h}

In reply to Bin Meng

Current SiFive PRCI model only works with sifive_e machine, as it only emulates registers or PRCI block in the FE310 SoC.

Rename the file name to make it clear that it is for sifive_e.

---

 hw/riscv/Makefile.objs                              |  2 +-
 hw/riscv/sifive_e.c                                 |  4 ++--
 hw/riscv/{sifive_prci.c => sifive_e_prci.c}         | 14 +++++++-------
 include/hw/riscv/{sifive_prci.h => sifive_e_prci.h} | 14 +++++++-------
 4 files changed, 17 insertions(+), 17 deletions(-)
 rename hw/riscv/{sifive_prci.c => sifive_e_prci.c} (90%)
 rename include/hw/riscv/{sifive_prci.h => sifive_e_prci.h} (82%)
hw/riscv/Makefile.objs +1 -1
index eb9d4f9..c859697 100644
@@ -2,9 +2,9 @@ obj-y += boot.o
 obj-$(CONFIG_SPIKE) += riscv_htif.o
 obj-$(CONFIG_HART) += riscv_hart.o
 obj-$(CONFIG_SIFIVE_E) += sifive_e.o
+obj-$(CONFIG_SIFIVE_E) += sifive_e_prci.o
 obj-$(CONFIG_SIFIVE) += sifive_clint.o
 obj-$(CONFIG_SIFIVE) += sifive_gpio.o
-obj-$(CONFIG_SIFIVE) += sifive_prci.o
 obj-$(CONFIG_SIFIVE) += sifive_plic.o
 obj-$(CONFIG_SIFIVE) += sifive_test.o
 obj-$(CONFIG_SIFIVE_U) += sifive_u.o
hw/riscv/sifive_e.c +2 -2
index 2a499d8..2d67670 100644
@@ -41,9 +41,9 @@
 #include "hw/riscv/riscv_hart.h"
 #include "hw/riscv/sifive_plic.h"
 #include "hw/riscv/sifive_clint.h"
-#include "hw/riscv/sifive_prci.h"
 #include "hw/riscv/sifive_uart.h"
 #include "hw/riscv/sifive_e.h"
+#include "hw/riscv/sifive_e_prci.h"
 #include "hw/riscv/boot.h"
 #include "chardev/char.h"
 #include "sysemu/arch_init.h"
@@ -174,7 +174,7 @@ static void riscv_sifive_e_soc_realize(DeviceState *dev, Error **errp)
         SIFIVE_SIP_BASE, SIFIVE_TIMECMP_BASE, SIFIVE_TIME_BASE);
     sifive_mmio_emulate(sys_mem, "riscv.sifive.e.aon",
         memmap[SIFIVE_E_AON].base, memmap[SIFIVE_E_AON].size);
-    sifive_prci_create(memmap[SIFIVE_E_PRCI].base);
+    sifive_e_prci_create(memmap[SIFIVE_E_PRCI].base);
 
     /* GPIO */
 
hw/riscv/sifive_e_prci.c renamed from hw/riscv/sifive_prci.c +7 -7
similarity index 90%
rename from hw/riscv/sifive_prci.c
rename to hw/riscv/sifive_e_prci.c
index f406682..acb914d 100644
@@ -1,5 +1,5 @@
 /*
- * QEMU SiFive PRCI (Power, Reset, Clock, Interrupt)
+ * QEMU SiFive E PRCI (Power, Reset, Clock, Interrupt)
  *
  * Copyright (c) 2017 SiFive, Inc.
  *
@@ -22,7 +22,7 @@
 #include "hw/sysbus.h"
 #include "qemu/module.h"
 #include "target/riscv/cpu.h"
-#include "hw/riscv/sifive_prci.h"
+#include "hw/riscv/sifive_e_prci.h"
 
 static uint64_t sifive_prci_read(void *opaque, hwaddr addr, unsigned int size)
 {
@@ -82,10 +82,10 @@ static const MemoryRegionOps sifive_prci_ops = {
 
 static void sifive_prci_init(Object *obj)
 {
-    SiFivePRCIState *s = SIFIVE_PRCI(obj);
+    SiFivePRCIState *s = SIFIVE_E_PRCI(obj);
 
     memory_region_init_io(&s->mmio, obj, &sifive_prci_ops, s,
-                          TYPE_SIFIVE_PRCI, 0x8000);
+                          TYPE_SIFIVE_E_PRCI, 0x8000);
     sysbus_init_mmio(SYS_BUS_DEVICE(obj), &s->mmio);
 
     s->hfrosccfg = (SIFIVE_PRCI_HFROSCCFG_RDY | SIFIVE_PRCI_HFROSCCFG_EN);
@@ -97,7 +97,7 @@ static void sifive_prci_init(Object *obj)
 }
 
 static const TypeInfo sifive_prci_info = {
-    .name          = TYPE_SIFIVE_PRCI,
+    .name          = TYPE_SIFIVE_E_PRCI,
     .parent        = TYPE_SYS_BUS_DEVICE,
     .instance_size = sizeof(SiFivePRCIState),
     .instance_init = sifive_prci_init,
@@ -114,9 +114,9 @@ type_init(sifive_prci_register_types)
 /*
  * Create PRCI device.
  */
-DeviceState *sifive_prci_create(hwaddr addr)
+DeviceState *sifive_e_prci_create(hwaddr addr)
 {
-    DeviceState *dev = qdev_create(NULL, TYPE_SIFIVE_PRCI);
+    DeviceState *dev = qdev_create(NULL, TYPE_SIFIVE_E_PRCI);
     qdev_init_nofail(dev);
     sysbus_mmio_map(SYS_BUS_DEVICE(dev), 0, addr);
     return dev;
include/hw/riscv/sifive_e_prci.h renamed from include/hw/riscv/sifive_prci.h +7 -7
similarity index 82%
rename from include/hw/riscv/sifive_prci.h
rename to include/hw/riscv/sifive_e_prci.h
index bd51c4a..7932fe7 100644
@@ -1,5 +1,5 @@
 /*
- * QEMU SiFive PRCI (Power, Reset, Clock, Interrupt) interface
+ * QEMU SiFive E PRCI (Power, Reset, Clock, Interrupt) interface
  *
  * Copyright (c) 2017 SiFive, Inc.
  *
@@ -16,8 +16,8 @@
  * this program.  If not, see <http://www.gnu.org/licenses/>.
  */
 
-#ifndef HW_SIFIVE_PRCI_H
-#define HW_SIFIVE_PRCI_H
+#ifndef HW_SIFIVE_E_PRCI_H
+#define HW_SIFIVE_E_PRCI_H
 
 enum {
     SIFIVE_PRCI_HFROSCCFG   = 0x0,
@@ -47,10 +47,10 @@ enum {
     SIFIVE_PRCI_PLLOUTDIV_DIV1  = (1 << 8)
 };
 
-#define TYPE_SIFIVE_PRCI "riscv.sifive.prci"
+#define TYPE_SIFIVE_E_PRCI      "riscv.sifive.e.prci"
 
-#define SIFIVE_PRCI(obj) \
-    OBJECT_CHECK(SiFivePRCIState, (obj), TYPE_SIFIVE_PRCI)
+#define SIFIVE_E_PRCI(obj) \
+    OBJECT_CHECK(SiFivePRCIState, (obj), TYPE_SIFIVE_E_PRCI)
 
 typedef struct SiFivePRCIState {
     /*< private >*/
@@ -64,6 +64,6 @@ typedef struct SiFivePRCIState {
     uint32_t plloutdiv;
 } SiFivePRCIState;
 
-DeviceState *sifive_prci_create(hwaddr addr);
+DeviceState *sifive_e_prci_create(hwaddr addr);
 
 #endif
Signature · 1 line
2.7.4
author
#21 lore raw

PATCH 12/28 riscv: sifive_e: prci: Fix a typo of hfxosccfg register programming

In reply to Bin Meng

It should use SIFIVE_PRCI_HFXOSCCFG_RDY and SIFIVE_PRCI_HFXOSCCFG_EN for hfxosccfg register programming.

---

 hw/riscv/sifive_e_prci.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
hw/riscv/sifive_e_prci.c +1 -1
index acb914d..c906f11 100644
@@ -89,7 +89,7 @@ static void sifive_prci_init(Object *obj)
     sysbus_init_mmio(SYS_BUS_DEVICE(obj), &s->mmio);
 
     s->hfrosccfg = (SIFIVE_PRCI_HFROSCCFG_RDY | SIFIVE_PRCI_HFROSCCFG_EN);
-    s->hfxosccfg = (SIFIVE_PRCI_HFROSCCFG_RDY | SIFIVE_PRCI_HFROSCCFG_EN);
+    s->hfxosccfg = (SIFIVE_PRCI_HFXOSCCFG_RDY | SIFIVE_PRCI_HFXOSCCFG_EN);
     s->pllcfg = (SIFIVE_PRCI_PLLCFG_REFSEL | SIFIVE_PRCI_PLLCFG_BYPASS |
                 SIFIVE_PRCI_PLLCFG_LOCK);
     s->plloutdiv = SIFIVE_PRCI_PLLOUTDIV_DIV1;
Signature · 1 line
2.7.4
Acked-by on v1 12/28
#22 lore raw

Re: [Qemu-devel] [PATCH 12/28] riscv: sifive_e: prci: Fix a typo of hfxosccfg register programming

Quoted 5 lines · Bin Meng

It should use SIFIVE_PRCI_HFXOSCCFG_RDY and SIFIVE_PRCI_HFXOSCCFG_EN for hfxosccfg register programming.

Alistair

Quoted 22 lines

---

 hw/riscv/sifive_e_prci.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
hw/riscv/sifive_e_prci.c +1 -2
index acb914d..c906f11 100644
@@ -89,7 +89,7 @@ static void sifive_prci_init(Object *obj)
     sysbus_init_mmio(SYS_BUS_DEVICE(obj), &s->mmio);
 
     s->hfrosccfg = (SIFIVE_PRCI_HFROSCCFG_RDY | SIFIVE_PRCI_HFROSCCFG_EN);
-    s->hfxosccfg = (SIFIVE_PRCI_HFROSCCFG_RDY | SIFIVE_PRCI_HFROSCCFG_EN);
+    s->hfxosccfg = (SIFIVE_PRCI_HFXOSCCFG_RDY | SIFIVE_PRCI_HFXOSCCFG_EN);
     s->pllcfg = (SIFIVE_PRCI_PLLCFG_REFSEL | SIFIVE_PRCI_PLLCFG_BYPASS |
                 SIFIVE_PRCI_PLLCFG_LOCK);
     s->plloutdiv = SIFIVE_PRCI_PLLOUTDIV_DIV1;
--

2.7.4

author
#23 lore raw

PATCH 13/28 riscv: sifive_e: prci: Update the PRCI register block size

In reply to Bin Meng

Currently the PRCI register block size is set to 0x8000, but in fact 0x1000 is enough, which is also what the manual says.

---

 hw/riscv/sifive_e_prci.c         | 2 +-
 include/hw/riscv/sifive_e_prci.h | 2 ++
 2 files changed, 3 insertions(+), 1 deletion(-)
hw/riscv/sifive_e_prci.c +1 -1
index c906f11..4cbce48 100644
@@ -85,7 +85,7 @@ static void sifive_prci_init(Object *obj)
     SiFivePRCIState *s = SIFIVE_E_PRCI(obj);
 
     memory_region_init_io(&s->mmio, obj, &sifive_prci_ops, s,
-                          TYPE_SIFIVE_E_PRCI, 0x8000);
+                          TYPE_SIFIVE_E_PRCI, SIFIVE_E_PRCI_REG_SIZE);
     sysbus_init_mmio(SYS_BUS_DEVICE(obj), &s->mmio);
 
     s->hfrosccfg = (SIFIVE_PRCI_HFROSCCFG_RDY | SIFIVE_PRCI_HFROSCCFG_EN);
include/hw/riscv/sifive_e_prci.h +2 -0
index 7932fe7..81e506b 100644
@@ -47,6 +47,8 @@ enum {
     SIFIVE_PRCI_PLLOUTDIV_DIV1  = (1 << 8)
 };
 
+#define SIFIVE_E_PRCI_REG_SIZE  0x1000
+
 #define TYPE_SIFIVE_E_PRCI      "riscv.sifive.e.prci"
 
 #define SIFIVE_E_PRCI(obj) \
Signature · 1 line
2.7.4
author
#24 lore raw

PATCH 14/28 riscv: sifive: Implement PRCI model for FU540

In reply to Bin Meng

This adds a simple PRCI model for FU540 (sifive_u). It has different register layout from the existing PRCI model for FE310 (sifive_e).

---

 hw/riscv/Makefile.objs           |   1 +
 hw/riscv/sifive_u_prci.c         | 163 +++++++++++++++++++++++++++++++++++++++
 include/hw/riscv/sifive_u_prci.h |  90 +++++++++++++++++++++
 3 files changed, 254 insertions(+)
 create mode 100644 hw/riscv/sifive_u_prci.c
 create mode 100644 include/hw/riscv/sifive_u_prci.h
hw/riscv/Makefile.objs +1 -0
index c859697..b95bbd5 100644
@@ -8,6 +8,7 @@ obj-$(CONFIG_SIFIVE) += sifive_gpio.o
 obj-$(CONFIG_SIFIVE) += sifive_plic.o
 obj-$(CONFIG_SIFIVE) += sifive_test.o
 obj-$(CONFIG_SIFIVE_U) += sifive_u.o
+obj-$(CONFIG_SIFIVE_U) += sifive_u_prci.o
 obj-$(CONFIG_SIFIVE) += sifive_uart.o
 obj-$(CONFIG_SPIKE) += spike.o
 obj-$(CONFIG_RISCV_VIRT) += virt.o
hw/riscv/sifive_u_prci.c new file +163 -0

163 lines not on this page · raw message

include/hw/riscv/sifive_u_prci.h new file +90 -0

90 lines not on this page · raw message

Signature · 1 line
2.7.4
author
#25 lore raw

PATCH 15/28 riscv: sifive_u: Generate hfclk and rtcclk nodes

In reply to Bin Meng

To keep in sync with Linux kernel device tree, generate hfclk and rtcclk nodes in the device tree, to be referenced by PRCI node.

---

 hw/riscv/sifive_u.c         | 23 +++++++++++++++++++++++
 include/hw/riscv/sifive_u.h |  2 ++
 2 files changed, 25 insertions(+)
hw/riscv/sifive_u.c +23 -0
index dfcb525..f619ca6 100644
@@ -76,6 +76,7 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
     char *nodename;
     char ethclk_names[] = "pclk\0hclk\0tx_clk";
     uint32_t plic_phandle, ethclk_phandle, phandle = 1;
+    uint32_t hfclk_phandle, rtcclk_phandle;
 
     fdt = s->fdt = create_device_tree(&s->fdt_size);
     if (!fdt) {
@@ -94,6 +95,28 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
     qemu_fdt_setprop_cell(fdt, "/soc", "#size-cells", 0x2);
     qemu_fdt_setprop_cell(fdt, "/soc", "#address-cells", 0x2);
 
+    hfclk_phandle = phandle++;
+    nodename = g_strdup_printf("/hfclk");
+    qemu_fdt_add_subnode(fdt, nodename);
+    qemu_fdt_setprop_cell(fdt, nodename, "phandle", hfclk_phandle);
+    qemu_fdt_setprop_string(fdt, nodename, "clock-output-names", "hfclk");
+    qemu_fdt_setprop_cell(fdt, nodename, "clock-frequency",
+        SIFIVE_U_HFCLK_FREQ);
+    qemu_fdt_setprop_string(fdt, nodename, "compatible", "fixed-clock");
+    qemu_fdt_setprop_cell(fdt, nodename, "#clock-cells", 0x0);
+    g_free(nodename);
+
+    rtcclk_phandle = phandle++;
+    nodename = g_strdup_printf("/rtcclk");
+    qemu_fdt_add_subnode(fdt, nodename);
+    qemu_fdt_setprop_cell(fdt, nodename, "phandle", rtcclk_phandle);
+    qemu_fdt_setprop_string(fdt, nodename, "clock-output-names", "rtcclk");
+    qemu_fdt_setprop_cell(fdt, nodename, "clock-frequency",
+        SIFIVE_U_RTCCLK_FREQ);
+    qemu_fdt_setprop_string(fdt, nodename, "compatible", "fixed-clock");
+    qemu_fdt_setprop_cell(fdt, nodename, "#clock-cells", 0x0);
+    g_free(nodename);
+
     nodename = g_strdup_printf("/memory@%lx",
         (long)memmap[SIFIVE_U_DRAM].base);
     qemu_fdt_add_subnode(fdt, nodename);
include/hw/riscv/sifive_u.h +2 -0
index 4abc621..bacd60f 100644
@@ -65,6 +65,8 @@ enum {
 
 enum {
     SIFIVE_U_CLOCK_FREQ = 1000000000,
+    SIFIVE_U_HFCLK_FREQ = 33333333,
+    SIFIVE_U_RTCCLK_FREQ = 1000000,
     SIFIVE_U_GEM_CLOCK_FREQ = 125000000
 };
 
Signature · 1 line
2.7.4
author
#26 lore raw

PATCH 16/28 riscv: sifive_u: Add PRCI block to the SoC

In reply to Bin Meng

Add PRCI mmio base address and size mappings to sifive_u machine, and generate the corresponding device tree node.

---

 hw/riscv/sifive_u.c         | 21 ++++++++++++++++++++-
 include/hw/riscv/sifive_u.h |  1 +
 2 files changed, 21 insertions(+), 1 deletion(-)
hw/riscv/sifive_u.c +20 -1
index f619ca6..20dee52 100644
@@ -9,6 +9,7 @@
  * 0) UART
  * 1) CLINT (Core Level Interruptor)
  * 2) PLIC (Platform Level Interrupt Controller)
+ * 3) PRCI (Power, Reset, Clock, Interrupt)
  *
  * This board currently uses a hardcoded devicetree that indicates five harts.
  *
@@ -41,6 +42,7 @@
 #include "hw/riscv/sifive_clint.h"
 #include "hw/riscv/sifive_uart.h"
 #include "hw/riscv/sifive_u.h"
+#include "hw/riscv/sifive_u_prci.h"
 #include "hw/riscv/boot.h"
 #include "chardev/char.h"
 #include "sysemu/arch_init.h"
@@ -59,6 +61,7 @@ static const struct MemmapEntry {
     [SIFIVE_U_MROM] =     {     0x1000,    0x11000 },
     [SIFIVE_U_CLINT] =    {  0x2000000,    0x10000 },
     [SIFIVE_U_PLIC] =     {  0xc000000,  0x4000000 },
+    [SIFIVE_U_PRCI] =     { 0x10000000,     0x1000 },
     [SIFIVE_U_UART0] =    { 0x10010000,     0x1000 },
     [SIFIVE_U_UART1] =    { 0x10011000,     0x1000 },
     [SIFIVE_U_DRAM] =     { 0x80000000,        0x0 },
@@ -75,7 +78,7 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
     uint32_t *cells;
     char *nodename;
     char ethclk_names[] = "pclk\0hclk\0tx_clk";
-    uint32_t plic_phandle, ethclk_phandle, phandle = 1;
+    uint32_t plic_phandle, prci_phandle, ethclk_phandle, phandle = 1;
     uint32_t hfclk_phandle, rtcclk_phandle;
 
     fdt = s->fdt = create_device_tree(&s->fdt_size);
@@ -182,6 +185,21 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
     g_free(cells);
     g_free(nodename);
 
+    prci_phandle = phandle++;
+    nodename = g_strdup_printf("/soc/clock-controller@%lx",
+        (long)memmap[SIFIVE_U_PRCI].base);
+    qemu_fdt_add_subnode(fdt, nodename);
+    qemu_fdt_setprop_cell(fdt, nodename, "phandle", prci_phandle);
+    qemu_fdt_setprop_cell(fdt, nodename, "#clock-cells", 0x1);
+    qemu_fdt_setprop_cells(fdt, nodename, "clocks",
+        hfclk_phandle, rtcclk_phandle);
+    qemu_fdt_setprop_cells(fdt, nodename, "reg",
+        0x0, memmap[SIFIVE_U_PRCI].base,
+        0x0, memmap[SIFIVE_U_PRCI].size);
+    qemu_fdt_setprop_string(fdt, nodename, "compatible",
+        "sifive,fu540-c000-prci");
+    g_free(nodename);
+
     plic_phandle = phandle++;
     cells =  g_new0(uint32_t, s->soc.cpus.num_harts * 4 - 2);
     for (cpu = 0; cpu < s->soc.cpus.num_harts; cpu++) {
@@ -421,6 +439,7 @@ static void riscv_sifive_u_soc_realize(DeviceState *dev, Error **errp)
     sifive_clint_create(memmap[SIFIVE_U_CLINT].base,
         memmap[SIFIVE_U_CLINT].size, ms->smp.cpus,
         SIFIVE_SIP_BASE, SIFIVE_TIMECMP_BASE, SIFIVE_TIME_BASE);
+    sifive_u_prci_create(memmap[SIFIVE_U_PRCI].base);
 
     for (i = 0; i < SIFIVE_U_PLIC_NUM_SOURCES; i++) {
         plic_gpios[i] = qdev_get_gpio_in(DEVICE(s->plic), i);
include/hw/riscv/sifive_u.h +1 -0
index bacd60f..19d5a6f 100644
@@ -51,6 +51,7 @@ enum {
     SIFIVE_U_MROM,
     SIFIVE_U_CLINT,
     SIFIVE_U_PLIC,
+    SIFIVE_U_PRCI,
     SIFIVE_U_UART0,
     SIFIVE_U_UART1,
     SIFIVE_U_DRAM,
Signature · 1 line
2.7.4
author
#27 lore raw

PATCH 17/28 riscv: sifive_u: Change UART node name in device tree

In reply to Bin Meng

OpenSBI for fu540 does DT fix up (see fu540_modify_dt()) by updating chosen "stdout-path" to point to "/soc/serial@...", and U-Boot will use this information to locate the serial node and probe its driver. However currently we generate the UART node name as "/soc/uart@...", causing U-Boot fail to find the serial node in DT.

---

 hw/riscv/sifive_u.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
hw/riscv/sifive_u.c +1 -1
index 20dee52..8044166 100644
@@ -273,7 +273,7 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
     qemu_fdt_setprop_cell(fdt, nodename, "reg", 0x0);
     g_free(nodename);
 
-    nodename = g_strdup_printf("/soc/uart@%lx",
+    nodename = g_strdup_printf("/soc/serial@%lx",
         (long)memmap[SIFIVE_U_UART0].base);
     qemu_fdt_add_subnode(fdt, nodename);
     qemu_fdt_setprop_string(fdt, nodename, "compatible", "sifive,uart0");
Signature · 1 line
2.7.4
Reviewed-by on v1 17/28
#28 lore raw

Re: [Qemu-devel] [PATCH 17/28] riscv: sifive_u: Change UART node name in device tree

Quoted 8 lines · Bin Meng

OpenSBI for fu540 does DT fix up (see fu540_modify_dt()) by updating chosen "stdout-path" to point to "/soc/serial@...", and U-Boot will use this information to locate the serial node and probe its driver. However currently we generate the UART node name as "/soc/uart@...", causing U-Boot fail to find the serial node in DT.

Alistair

Quoted 22 lines

---

 hw/riscv/sifive_u.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
hw/riscv/sifive_u.c +1 -2
index 20dee52..8044166 100644
@@ -273,7 +273,7 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
     qemu_fdt_setprop_cell(fdt, nodename, "reg", 0x0);
     g_free(nodename);
 
-    nodename = g_strdup_printf("/soc/uart@%lx",
+    nodename = g_strdup_printf("/soc/serial@%lx",
         (long)memmap[SIFIVE_U_UART0].base);
     qemu_fdt_add_subnode(fdt, nodename);
     qemu_fdt_setprop_string(fdt, nodename, "compatible", "sifive,uart0");
--

2.7.4

author
#29 lore raw

PATCH 18/28 riscv: hw: Implement a model for SiFive FU540 OTP

In reply to Bin Meng

This implements a simple model for SiFive FU540 OTP (One-Time Programmable) Memory interface, primarily for reading out the stored serial number from the first 1 KiB of the 16 KiB OTP memory reserved by SiFive for internal use.

---

 hw/riscv/Makefile.objs          |   1 +
 hw/riscv/sifive_u_otp.c         | 194 ++++++++++++++++++++++++++++++++++++++++
 include/hw/riscv/sifive_u_otp.h |  90 +++++++++++++++++++
 3 files changed, 285 insertions(+)
 create mode 100644 hw/riscv/sifive_u_otp.c
 create mode 100644 include/hw/riscv/sifive_u_otp.h
hw/riscv/Makefile.objs +1 -0
index b95bbd5..fc3c6dd 100644
@@ -8,6 +8,7 @@ obj-$(CONFIG_SIFIVE) += sifive_gpio.o
 obj-$(CONFIG_SIFIVE) += sifive_plic.o
 obj-$(CONFIG_SIFIVE) += sifive_test.o
 obj-$(CONFIG_SIFIVE_U) += sifive_u.o
+obj-$(CONFIG_SIFIVE_U) += sifive_u_otp.o
 obj-$(CONFIG_SIFIVE_U) += sifive_u_prci.o
 obj-$(CONFIG_SIFIVE) += sifive_uart.o
 obj-$(CONFIG_SPIKE) += spike.o
hw/riscv/sifive_u_otp.c new file +194 -0

194 lines not on this page · raw message

include/hw/riscv/sifive_u_otp.h new file +90 -0

90 lines not on this page · raw message

Signature · 1 line
2.7.4
author
#30 lore raw

PATCH 21/28 riscv: sifive_u: Update UART and ethernet node clock properties

In reply to Bin Meng

Now that we have added PRCI nodes, update existing UART and ethernet nodes to use PRCI as their clock sources, to keep in sync with the Linux kernel device tree.

With above changes, the previously handcrafted "/soc/ethclk" node is no longer needed. Remove it.

---

 hw/riscv/sifive_u.c              | 21 +++++----------------
 include/hw/riscv/sifive_u.h      |  3 +--
 include/hw/riscv/sifive_u_prci.h | 10 ++++++++++
 3 files changed, 16 insertions(+), 18 deletions(-)
hw/riscv/sifive_u.c +5 -16
index b90aa53..061d6d4 100644
@@ -81,8 +81,8 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
     int cpu;
     uint32_t *cells;
     char *nodename;
-    char ethclk_names[] = "pclk\0hclk\0tx_clk";
-    uint32_t plic_phandle, prci_phandle, ethclk_phandle, phandle = 1;
+    char ethclk_names[] = "pclk\0hclk";
+    uint32_t plic_phandle, prci_phandle, phandle = 1;
     uint32_t hfclk_phandle, rtcclk_phandle;
 
     fdt = s->fdt = create_device_tree(&s->fdt_size);
@@ -241,17 +241,6 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
     g_free(cells);
     g_free(nodename);
 
-    ethclk_phandle = phandle++;
-    nodename = g_strdup_printf("/soc/ethclk");
-    qemu_fdt_add_subnode(fdt, nodename);
-    qemu_fdt_setprop_string(fdt, nodename, "compatible", "fixed-clock");
-    qemu_fdt_setprop_cell(fdt, nodename, "#clock-cells", 0x0);
-    qemu_fdt_setprop_cell(fdt, nodename, "clock-frequency",
-        SIFIVE_U_GEM_CLOCK_FREQ);
-    qemu_fdt_setprop_cell(fdt, nodename, "phandle", ethclk_phandle);
-    ethclk_phandle = qemu_fdt_get_phandle(fdt, nodename);
-    g_free(nodename);
-
     nodename = g_strdup_printf("/soc/ethernet@%lx",
         (long)memmap[SIFIVE_U_GEM].base);
     qemu_fdt_add_subnode(fdt, nodename);
@@ -264,7 +253,7 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
     qemu_fdt_setprop_cell(fdt, nodename, "interrupt-parent", plic_phandle);
     qemu_fdt_setprop_cell(fdt, nodename, "interrupts", SIFIVE_U_GEM_IRQ);
     qemu_fdt_setprop_cells(fdt, nodename, "clocks",
-        ethclk_phandle, ethclk_phandle, ethclk_phandle);
+        prci_phandle, PRCI_CLK_GEMGXLPLL, prci_phandle, PRCI_CLK_GEMGXLPLL);
     qemu_fdt_setprop(fdt, nodename, "clocks-names", ethclk_names,
         sizeof(ethclk_names));
     qemu_fdt_setprop_cell(fdt, nodename, "#address-cells", 1);
@@ -284,8 +273,8 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
     qemu_fdt_setprop_cells(fdt, nodename, "reg",
         0x0, memmap[SIFIVE_U_UART0].base,
         0x0, memmap[SIFIVE_U_UART0].size);
-    qemu_fdt_setprop_cell(fdt, nodename, "clock-frequency",
-                          SIFIVE_U_CLOCK_FREQ / 2);
+    qemu_fdt_setprop_cells(fdt, nodename, "clocks",
+        prci_phandle, PRCI_CLK_TLCLK);
     qemu_fdt_setprop_cell(fdt, nodename, "interrupt-parent", plic_phandle);
     qemu_fdt_setprop_cell(fdt, nodename, "interrupts", SIFIVE_U_UART0_IRQ);
 
include/hw/riscv/sifive_u.h +1 -2
index 2f475c5..0461331 100644
@@ -68,8 +68,7 @@ enum {
 enum {
     SIFIVE_U_CLOCK_FREQ = 1000000000,
     SIFIVE_U_HFCLK_FREQ = 33333333,
-    SIFIVE_U_RTCCLK_FREQ = 1000000,
-    SIFIVE_U_GEM_CLOCK_FREQ = 125000000
+    SIFIVE_U_RTCCLK_FREQ = 1000000
 };
 
 #define SIFIVE_U_PLIC_HART_CONFIG "MS"
include/hw/riscv/sifive_u_prci.h +10 -0
index f3a4656..640c641 100644
@@ -87,4 +87,14 @@ typedef struct SiFivePRCIState {
 
 DeviceState *sifive_u_prci_create(hwaddr addr);
 
+/*
+ * Clock indexes for use by Device Tree data and the PRCI driver.
+ *
+ * These values are from sifive-fu540-prci.h in the Linux kernel.
+ */
+#define PRCI_CLK_COREPLL        0
+#define PRCI_CLK_DDRPLL         1
+#define PRCI_CLK_GEMGXLPLL      2
+#define PRCI_CLK_TLCLK          3
+
 #endif /* HW_SIFIVE_U_PRCI_H */
Signature · 1 line
2.7.4
author
#31 lore raw

PATCH 22/28 riscv: sifive_u: Generate an aliases node in the device tree

In reply to Bin Meng

The Linux kernel SiFive UART driver expects an aliases node to be present in the device tree, from which the driver extracts the port number from "serial#" in the aliases node.

---

 hw/riscv/sifive_u.c | 2 ++
 1 file changed, 2 insertions(+)
hw/riscv/sifive_u.c +2 -0
index 061d6d4..9945b82 100644
@@ -283,6 +283,8 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
     if (cmdline) {
         qemu_fdt_setprop_string(fdt, "/chosen", "bootargs", cmdline);
     }
+    qemu_fdt_add_subnode(fdt, "/aliases");
+    qemu_fdt_setprop_string(fdt, "/aliases", "serial0", nodename);
     g_free(nodename);
 }
 
Signature · 1 line
2.7.4
author
#32 lore raw

PATCH 23/28 riscv: sifive: Move sifive_mmio_emulate() to a common place

In reply to Bin Meng

sifive_mmio_emulate() is currently only used in the sifive_e machine codes. It can be helpful for other machines as well.

Change it to an inline routine and move it to sifive_cpu.h, so that other machines like sifive_u can use it.

---

 hw/riscv/sifive_e.c           |  8 --------
 include/hw/riscv/sifive_cpu.h | 10 +++++++++-
 2 files changed, 9 insertions(+), 9 deletions(-)
hw/riscv/sifive_e.c +0 -8
index 2d67670..7e0fe7b 100644
@@ -74,14 +74,6 @@ static const struct MemmapEntry {
     [SIFIVE_E_DTIM] =     { 0x80000000,     0x4000 }
 };
 
-static void sifive_mmio_emulate(MemoryRegion *parent, const char *name,
-                             uintptr_t offset, uintptr_t length)
-{
-    MemoryRegion *mock_mmio = g_new(MemoryRegion, 1);
-    memory_region_init_ram(mock_mmio, NULL, name, length, &error_fatal);
-    memory_region_add_subregion(parent, offset, mock_mmio);
-}
-
 static void riscv_sifive_e_init(MachineState *machine)
 {
     const struct MemmapEntry *memmap = sifive_e_memmap;
include/hw/riscv/sifive_cpu.h +9 -1
index 1367996..897b8f8 100644
@@ -1,5 +1,5 @@
 /*
- * SiFive CPU types
+ * SiFive CPU types and common utilities
  *
  * Copyright (c) 2017 SiFive, Inc.
  * Copyright (c) 2019 Bin Meng <[email protected]>
@@ -28,4 +28,12 @@
 #define SIFIVE_U_CPU TYPE_RISCV_CPU_SIFIVE_U54
 #endif
 
+static inline void sifive_mmio_emulate(MemoryRegion *parent, const char *name,
+                                       uintptr_t offset, uintptr_t length)
+{
+    MemoryRegion *mock_mmio = g_new(MemoryRegion, 1);
+    memory_region_init_ram(mock_mmio, NULL, name, length, &error_fatal);
+    memory_region_add_subregion(parent, offset, mock_mmio);
+}
+
 #endif /* HW_SIFIVE_CPU_H */
Signature · 1 line
2.7.4
#33 lore raw

Re: [Qemu-devel] [PATCH 23/28] riscv: sifive: Move sifive_mmio_emulate() to a common place

Quoted 8 lines · Bin Meng

sifive_mmio_emulate() is currently only used in the sifive_e machine codes. It can be helpful for other machines as well.

Change it to an inline routine and move it to sifive_cpu.h, so that other machines like sifive_u can use it.

I don't like this. I don't think we should use this function. This seems like we can use create_unimplemented_device() instead.

Alistair

Quoted 53 lines

---

 hw/riscv/sifive_e.c           |  8 --------
 include/hw/riscv/sifive_cpu.h | 10 +++++++++-
 2 files changed, 9 insertions(+), 9 deletions(-)
hw/riscv/sifive_e.c +0 -8
index 2d67670..7e0fe7b 100644
@@ -74,14 +74,6 @@ static const struct MemmapEntry {
     [SIFIVE_E_DTIM] =     { 0x80000000,     0x4000 }
 };
 
-static void sifive_mmio_emulate(MemoryRegion *parent, const char *name,
-                             uintptr_t offset, uintptr_t length)
-{
-    MemoryRegion *mock_mmio = g_new(MemoryRegion, 1);
-    memory_region_init_ram(mock_mmio, NULL, name, length, &error_fatal);
-    memory_region_add_subregion(parent, offset, mock_mmio);
-}
-
 static void riscv_sifive_e_init(MachineState *machine)
 {
     const struct MemmapEntry *memmap = sifive_e_memmap;
include/hw/riscv/sifive_cpu.h +9 -2
index 1367996..897b8f8 100644
@@ -1,5 +1,5 @@
 /*
- * SiFive CPU types
+ * SiFive CPU types and common utilities
  *
  * Copyright (c) 2017 SiFive, Inc.
  * Copyright (c) 2019 Bin Meng <[email protected]>
@@ -28,4 +28,12 @@
 #define SIFIVE_U_CPU TYPE_RISCV_CPU_SIFIVE_U54
 #endif
 
+static inline void sifive_mmio_emulate(MemoryRegion *parent, const char *name,
+                                       uintptr_t offset, uintptr_t length)
+{
+    MemoryRegion *mock_mmio = g_new(MemoryRegion, 1);
+    memory_region_init_ram(mock_mmio, NULL, name, length, &error_fatal);
+    memory_region_add_subregion(parent, offset, mock_mmio);
+}
+
 #endif /* HW_SIFIVE_CPU_H */
--

2.7.4

author
#34 lore raw

PATCH 24/28 riscv: sifive_u: Fix broken GEM support

In reply to Bin Meng

At present the GEM support in sifive_u machine is seriously broken.

- The GEM block register base was set to a weird number (0x100900FC), which for no way could work with the cadence_gem model in QEMU.
- The generated DT node for GEM has a "clocks-names" which is an invalid property name.

Not like other GEM variants, the FU540-specific GEM has a management block to control 10/100/1000Mbps link speed changes, that is mapped to 0x100a0000. We can simply map it into MMIO space without special handling using sifive_mmio_emulate().

Update the GEM node compatible string to use the official name used by the upstream Linux kernel, and add the management block reg base & size to the <reg> property encoding.

Tested with upstream U-Boot and Linux kernel MACB drivers.

---

 hw/riscv/sifive_u.c         | 17 +++++++++++++----
 include/hw/riscv/sifive_u.h |  3 ++-
 2 files changed, 15 insertions(+), 5 deletions(-)
hw/riscv/sifive_u.c +13 -4
index 9945b82..85cd4b5 100644
@@ -3,6 +3,7 @@
  *
  * Copyright (c) 2016-2017 Sagar Karandikar, [email protected]
  * Copyright (c) 2017 SiFive, Inc.
+ * Copyright (c) 2019 Bin Meng <[email protected]>
  *
  * Provides a board compatible with the SiFive Freedom U SDK:
  *
@@ -11,6 +12,7 @@
  * 2) PLIC (Platform Level Interrupt Controller)
  * 3) PRCI (Power, Reset, Clock, Interrupt)
  * 4) OTP (One-Time Programmable) memory with stored serial number
+ * 5) GEM (Gigabit Ethernet Controller) and management block
  *
  * This board currently uses a hardcoded devicetree that indicates five harts.
  *
@@ -68,7 +70,8 @@ static const struct MemmapEntry {
     [SIFIVE_U_UART1] =    { 0x10011000,     0x1000 },
     [SIFIVE_U_OTP] =      { 0x10070000,     0x1000 },
     [SIFIVE_U_DRAM] =     { 0x80000000,        0x0 },
-    [SIFIVE_U_GEM] =      { 0x100900FC,     0x2000 },
+    [SIFIVE_U_GEM] =      { 0x10090000,     0x2000 },
+    [SIFIVE_U_GEM_MGMT] = { 0x100a0000,     0x1000 },
 };
 
 #define SIFIVE_OTP_SERIAL   1
@@ -244,17 +247,20 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
     nodename = g_strdup_printf("/soc/ethernet@%lx",
         (long)memmap[SIFIVE_U_GEM].base);
     qemu_fdt_add_subnode(fdt, nodename);
-    qemu_fdt_setprop_string(fdt, nodename, "compatible", "cdns,macb");
+    qemu_fdt_setprop_string(fdt, nodename, "compatible",
+        "sifive,fu540-c000-gem");
     qemu_fdt_setprop_cells(fdt, nodename, "reg",
         0x0, memmap[SIFIVE_U_GEM].base,
-        0x0, memmap[SIFIVE_U_GEM].size);
+        0x0, memmap[SIFIVE_U_GEM].size,
+        0x0, memmap[SIFIVE_U_GEM_MGMT].base,
+        0x0, memmap[SIFIVE_U_GEM_MGMT].size);
     qemu_fdt_setprop_string(fdt, nodename, "reg-names", "control");
     qemu_fdt_setprop_string(fdt, nodename, "phy-mode", "gmii");
     qemu_fdt_setprop_cell(fdt, nodename, "interrupt-parent", plic_phandle);
     qemu_fdt_setprop_cell(fdt, nodename, "interrupts", SIFIVE_U_GEM_IRQ);
     qemu_fdt_setprop_cells(fdt, nodename, "clocks",
         prci_phandle, PRCI_CLK_GEMGXLPLL, prci_phandle, PRCI_CLK_GEMGXLPLL);
-    qemu_fdt_setprop(fdt, nodename, "clocks-names", ethclk_names,
+    qemu_fdt_setprop(fdt, nodename, "clock-names", ethclk_names,
         sizeof(ethclk_names));
     qemu_fdt_setprop_cell(fdt, nodename, "#address-cells", 1);
     qemu_fdt_setprop_cell(fdt, nodename, "#size-cells", 0);
@@ -455,6 +461,9 @@ static void riscv_sifive_u_soc_realize(DeviceState *dev, Error **errp)
     sysbus_mmio_map(SYS_BUS_DEVICE(&s->gem), 0, memmap[SIFIVE_U_GEM].base);
     sysbus_connect_irq(SYS_BUS_DEVICE(&s->gem), 0,
                        plic_gpios[SIFIVE_U_GEM_IRQ]);
+
+    sifive_mmio_emulate(system_memory, "riscv.sifive.u.gem-mgmt",
+        memmap[SIFIVE_U_GEM_MGMT].base, memmap[SIFIVE_U_GEM_MGMT].size);
 }
 
 static void riscv_sifive_u_machine_init(MachineClass *mc)
include/hw/riscv/sifive_u.h +2 -1
index 0461331..e92f1aa 100644
@@ -56,7 +56,8 @@ enum {
     SIFIVE_U_UART1,
     SIFIVE_U_OTP,
     SIFIVE_U_DRAM,
-    SIFIVE_U_GEM
+    SIFIVE_U_GEM,
+    SIFIVE_U_GEM_MGMT
 };
 
 enum {
Signature · 1 line
2.7.4
author
#35 lore raw

PATCH 25/28 riscv: sifive_u: Support loading initramfs

In reply to Bin Meng

The loading of initramfs is currently not supported on 'sifive_u'. Add the support to make '-initrd' command line parameter useful.

---

 hw/riscv/sifive_u.c | 13 ++++++++++++-
 1 file changed, 12 insertions(+), 1 deletion(-)
hw/riscv/sifive_u.c +12 -1
index 85cd4b5..d77b3c3 100644
@@ -323,7 +323,18 @@ static void riscv_sifive_u_init(MachineState *machine)
                                  memmap[SIFIVE_U_DRAM].base);
 
     if (machine->kernel_filename) {
-        riscv_load_kernel(machine->kernel_filename);
+        uint64_t kernel_entry = riscv_load_kernel(machine->kernel_filename);
+
+        if (machine->initrd_filename) {
+            hwaddr start;
+            hwaddr end = riscv_load_initrd(machine->initrd_filename,
+                                           machine->ram_size, kernel_entry,
+                                           &start);
+            qemu_fdt_setprop_cell(s->fdt, "/chosen",
+                                  "linux,initrd-start", start);
+            qemu_fdt_setprop_cell(s->fdt, "/chosen", "linux,initrd-end",
+                                  end);
+        }
     }
 
     /* reset vector */
Signature · 1 line
2.7.4
author
#36 lore raw

PATCH 26/28 riscv: hw: Update PLIC device tree

In reply to Bin Meng

This removes "reg-names" and "riscv,max-priority" properties of the PLIC node from device tree, and updates its compatible string, to keep in sync with the Linux kernel device tree.

---

 hw/riscv/sifive_u.c | 4 +---
 hw/riscv/virt.c     | 4 +---
 2 files changed, 2 insertions(+), 6 deletions(-)
hw/riscv/sifive_u.c +1 -3
index d77b3c3..5ded3a0 100644
@@ -229,15 +229,13 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
         (long)memmap[SIFIVE_U_PLIC].base);
     qemu_fdt_add_subnode(fdt, nodename);
     qemu_fdt_setprop_cell(fdt, nodename, "#interrupt-cells", 1);
-    qemu_fdt_setprop_string(fdt, nodename, "compatible", "riscv,plic0");
+    qemu_fdt_setprop_string(fdt, nodename, "compatible", "sifive,plic-1.0.0");
     qemu_fdt_setprop(fdt, nodename, "interrupt-controller", NULL, 0);
     qemu_fdt_setprop(fdt, nodename, "interrupts-extended",
         cells, s->soc.cpus.num_harts * sizeof(uint32_t) * 4);
     qemu_fdt_setprop_cells(fdt, nodename, "reg",
         0x0, memmap[SIFIVE_U_PLIC].base,
         0x0, memmap[SIFIVE_U_PLIC].size);
-    qemu_fdt_setprop_string(fdt, nodename, "reg-names", "control");
-    qemu_fdt_setprop_cell(fdt, nodename, "riscv,max-priority", 7);
     qemu_fdt_setprop_cell(fdt, nodename, "riscv,ndev", 0x35);
     qemu_fdt_setprop_cell(fdt, nodename, "phandle", plic_phandle);
     plic_phandle = qemu_fdt_get_phandle(fdt, nodename);
hw/riscv/virt.c +1 -3
index 127f005..f662100 100644
@@ -237,15 +237,13 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
                           FDT_PLIC_ADDR_CELLS);
     qemu_fdt_setprop_cell(fdt, nodename, "#interrupt-cells",
                           FDT_PLIC_INT_CELLS);
-    qemu_fdt_setprop_string(fdt, nodename, "compatible", "riscv,plic0");
+    qemu_fdt_setprop_string(fdt, nodename, "compatible", "sifive,plic-1.0.0");
     qemu_fdt_setprop(fdt, nodename, "interrupt-controller", NULL, 0);
     qemu_fdt_setprop(fdt, nodename, "interrupts-extended",
         cells, s->soc.num_harts * sizeof(uint32_t) * 4);
     qemu_fdt_setprop_cells(fdt, nodename, "reg",
         0x0, memmap[VIRT_PLIC].base,
         0x0, memmap[VIRT_PLIC].size);
-    qemu_fdt_setprop_string(fdt, nodename, "reg-names", "control");
-    qemu_fdt_setprop_cell(fdt, nodename, "riscv,max-priority", 7);
     qemu_fdt_setprop_cell(fdt, nodename, "riscv,ndev", VIRTIO_NDEV);
     qemu_fdt_setprop_cell(fdt, nodename, "phandle", plic_phandle);
     plic_phandle = qemu_fdt_get_phandle(fdt, nodename);
Signature · 1 line
2.7.4
Reviewed-by on v1 26/28
#37 lore raw

Re: [Qemu-devel] [Qemu-riscv] [PATCH 26/28] riscv: hw: Update PLIC device tree

I was a little surprised to see the "riscv,max-priority" element removed, but there is no mention of it in the kernel documentation
<https://github.com/torvalds/linux/blob/master/Documentation/devicetree/bindings/interrupt-controller/sifive%2Cplic-1.0.0.txt>
so I guess that max-priority=7 is now assumed.

Quoted 62 lines · Bin Meng

This removes "reg-names" and "riscv,max-priority" properties of the PLIC node from device tree, and updates its compatible string, to keep in sync with the Linux kernel device tree.

---

 hw/riscv/sifive_u.c | 4 +---
 hw/riscv/virt.c     | 4 +---
 2 files changed, 2 insertions(+), 6 deletions(-)
hw/riscv/sifive_u.c +1 -3
index d77b3c3..5ded3a0 100644
@@ -229,15 +229,13 @@ static void create_fdt(SiFiveUState *s, const struct
 MemmapEntry *memmap,
         (long)memmap[SIFIVE_U_PLIC].base);
     qemu_fdt_add_subnode(fdt, nodename);
     qemu_fdt_setprop_cell(fdt, nodename, "#interrupt-cells", 1);
-    qemu_fdt_setprop_string(fdt, nodename, "compatible", "riscv,plic0");
+    qemu_fdt_setprop_string(fdt, nodename, "compatible",
 "sifive,plic-1.0.0");
     qemu_fdt_setprop(fdt, nodename, "interrupt-controller", NULL, 0);
     qemu_fdt_setprop(fdt, nodename, "interrupts-extended",
         cells, s->soc.cpus.num_harts * sizeof(uint32_t) * 4);
     qemu_fdt_setprop_cells(fdt, nodename, "reg",
         0x0, memmap[SIFIVE_U_PLIC].base,
         0x0, memmap[SIFIVE_U_PLIC].size);
-    qemu_fdt_setprop_string(fdt, nodename, "reg-names", "control");
-    qemu_fdt_setprop_cell(fdt, nodename, "riscv,max-priority", 7);
     qemu_fdt_setprop_cell(fdt, nodename, "riscv,ndev", 0x35);
     qemu_fdt_setprop_cell(fdt, nodename, "phandle", plic_phandle);
     plic_phandle = qemu_fdt_get_phandle(fdt, nodename);
hw/riscv/virt.c +1 -3
index 127f005..f662100 100644
@@ -237,15 +237,13 @@ static void *create_fdt(RISCVVirtState *s, const
 struct MemmapEntry *memmap,
                           FDT_PLIC_ADDR_CELLS);
     qemu_fdt_setprop_cell(fdt, nodename, "#interrupt-cells",
                           FDT_PLIC_INT_CELLS);
-    qemu_fdt_setprop_string(fdt, nodename, "compatible", "riscv,plic0");
+    qemu_fdt_setprop_string(fdt, nodename, "compatible",
 "sifive,plic-1.0.0");
     qemu_fdt_setprop(fdt, nodename, "interrupt-controller", NULL, 0);
     qemu_fdt_setprop(fdt, nodename, "interrupts-extended",
         cells, s->soc.num_harts * sizeof(uint32_t) * 4);
     qemu_fdt_setprop_cells(fdt, nodename, "reg",
         0x0, memmap[VIRT_PLIC].base,
         0x0, memmap[VIRT_PLIC].size);
-    qemu_fdt_setprop_string(fdt, nodename, "reg-names", "control");
-    qemu_fdt_setprop_cell(fdt, nodename, "riscv,max-priority", 7);
     qemu_fdt_setprop_cell(fdt, nodename, "riscv,ndev", VIRTIO_NDEV);
     qemu_fdt_setprop_cell(fdt, nodename, "phandle", plic_phandle);
     plic_phandle = qemu_fdt_get_phandle(fdt, nodename);

--
2.7.4

author
#38 lore raw

PATCH 27/28 riscv: virt: Change create_fdt() to return void

In reply to Bin Meng

There is no need to return fdt at the end of create_fdt() because it's already saved in s->fdt. Other machines (sifive_u, spike) don't do it neither.

---

 hw/riscv/virt.c | 11 ++++-------
 1 file changed, 4 insertions(+), 7 deletions(-)
hw/riscv/virt.c +4 -7
index f662100..5935ac8 100644
@@ -112,7 +112,7 @@ static void create_pcie_irq_map(void *fdt, char *nodename,
                            0x1800, 0, 0, 0x7);
 }
 
-static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
+static void create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
     uint64_t mem_size, const char *cmdline)
 {
     void *fdt;
@@ -316,8 +316,6 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
         qemu_fdt_setprop_string(fdt, "/chosen", "bootargs", cmdline);
     }
     g_free(nodename);
-
-    return fdt;
 }
 
 
@@ -373,7 +371,6 @@ static void riscv_virt_board_init(MachineState *machine)
     size_t plic_hart_config_len;
     int i;
     unsigned int smp_cpus = machine->smp.cpus;
-    void *fdt;
 
     /* Initialize SOC */
     object_initialize_child(OBJECT(machine), "soc", &s->soc, sizeof(s->soc),
@@ -392,7 +389,7 @@ static void riscv_virt_board_init(MachineState *machine)
         main_mem);
 
     /* create device tree */
-    fdt = create_fdt(s, memmap, machine->ram_size, machine->kernel_cmdline);
+    create_fdt(s, memmap, machine->ram_size, machine->kernel_cmdline);
 
     /* boot rom */
     memory_region_init_rom(mask_rom, NULL, "riscv_virt_board.mrom",
@@ -411,9 +408,9 @@ static void riscv_virt_board_init(MachineState *machine)
             hwaddr end = riscv_load_initrd(machine->initrd_filename,
                                            machine->ram_size, kernel_entry,
                                            &start);
-            qemu_fdt_setprop_cell(fdt, "/chosen",
+            qemu_fdt_setprop_cell(s->fdt, "/chosen",
                                   "linux,initrd-start", start);
-            qemu_fdt_setprop_cell(fdt, "/chosen", "linux,initrd-end",
+            qemu_fdt_setprop_cell(s->fdt, "/chosen", "linux,initrd-end",
                                   end);
         }
     }
Signature · 1 line
2.7.4
author
#39 lore raw

PATCH 28/28 riscv: sifive_u: Update model and compatible strings in device tree

In reply to Bin Meng

This updates model and compatible strings to use the same strings as used in the Linux kernel device tree (hifive-unleashed-a00.dts).

---

 hw/riscv/sifive_u.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
hw/riscv/sifive_u.c +3 -2
index 5ded3a0..b7d4b4f 100644
@@ -94,8 +94,9 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
         exit(1);
     }
 
-    qemu_fdt_setprop_string(fdt, "/", "model", "ucbbar,spike-bare,qemu");
-    qemu_fdt_setprop_string(fdt, "/", "compatible", "ucbbar,spike-bare-dev");
+    qemu_fdt_setprop_string(fdt, "/", "model", "SiFive HiFive Unleashed A00");
+    qemu_fdt_setprop_string(fdt, "/", "compatible",
+                            "sifive,hifive-unleashed-a00");
     qemu_fdt_setprop_cell(fdt, "/", "#size-cells", 0x2);
     qemu_fdt_setprop_cell(fdt, "/", "#address-cells", 0x2);
 
Signature · 1 line
2.7.4
Reviewed-by on v1 28/28
#40 lore raw

Re: [Qemu-devel] [PATCH 28/28] riscv: sifive_u: Update model and compatible strings in device tree

Quoted 5 lines · Bin Meng

This updates model and compatible strings to use the same strings as used in the Linux kernel device tree (hifive-unleashed-a00.dts).

Alistair

Quoted 26 lines

---

 hw/riscv/sifive_u.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
hw/riscv/sifive_u.c +3 -3
index 5ded3a0..b7d4b4f 100644
@@ -94,8 +94,9 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
         exit(1);
     }
 
-    qemu_fdt_setprop_string(fdt, "/", "model", "ucbbar,spike-bare,qemu");
-    qemu_fdt_setprop_string(fdt, "/", "compatible", "ucbbar,spike-bare-dev");
+    qemu_fdt_setprop_string(fdt, "/", "model", "SiFive HiFive Unleashed A00");
+    qemu_fdt_setprop_string(fdt, "/", "compatible",
+                            "sifive,hifive-unleashed-a00");
     qemu_fdt_setprop_cell(fdt, "/", "#size-cells", 0x2);
     qemu_fdt_setprop_cell(fdt, "/", "#address-cells", 0x2);
 
--

2.7.4