riscv: sifive_u: Improve the emulation fidelity of sifive_u machine
Subsystems (2)
v2 cover riscv: sifive_u: Improve the emulation fidelity of sifive_u machine
As of today, the QEMU 'sifive_u' machine is a special target that does not boot the upstream OpenSBI/U-Boot firmware images built for the real SiFive HiFive Unleashed board. Hence OpenSBI supports a special platform "qemu/sifive_u". For U-Boot, the sifive_fu540_defconfig is referenced in the OpenSBI doc as its payload, but that does not boot at all due to various issues in current QEMU 'sifive_u' machine codes.
This series aims to improve the emulation fidelity of sifive_u machine, so that the upstream OpenSBI, U-Boot and kernel images built for the SiFive HiFive Unleashed board can be used out of the box without any special hack.
The major changes include:
- Heterogeneous harts creation supported, so that we can create a CPU that exactly mirrors the real hardware: 1 E51 + 4 U54.
- Implemented a PRCI model for FU540
- Implemented an OTP model for FU540, primarily used for storing serial number of the board
- Fixed GEM support that was seriously broken on sifive_u
- Synced device tree with upstream Linux kernel on sifive_u
- Adding initramfs loading support on sifive_u
OpenSBI v0.4 image built for sifive/fu540 is included as the default bios image for 'sifive_u' machine.
The series is tested against OpenSBI v0.4 image for sifive/fu540 paltform, U-Boot v2019.10-rc1 image for sifive_fu540_defconfig, and Linux kernel v5.3-rc3 image with the following patch:
macb: Update compatibility string for SiFive FU540-C000
https://patchwork.kernel.org/patch/11050003/
OpenSBI + U-Boot, ping/tftpboot with U-Boot MACB driver works well. Boot Linux 64-bit defconfig image, verified that system console on the serial 0 and ping host work pretty well.
Changes in v2:
- fixed the "interrupts-extended" property size
- update the file header to indicate at least 2 harts are created
- use create_unimplemented_device() to create the GEM management block instead of sifive_mmio_emulate()
- add "phy-handle" property to the ethernet node
- keep the PLIC compatible string unchanged as OpenSBI uses that for DT fix up
- drop patch "riscv: sifive: Move sifive_mmio_emulate() to a common place"
- new patch "riscv: sifive_e: Drop sifive_mmio_emulate()"
Bin Meng (28):
riscv: hw: Remove superfluous "linux,phandle" property
riscv: hw: Use qemu_fdt_setprop_cell() for property with only 1 cell
riscv: Add a sifive_cpu.h to include both E and U cpu type defines
riscv: hart: Extract hart realize to a separate routine
riscv: hart: Support heterogeneous harts population
riscv: sifive_u: Update hart configuration to reflect the real FU540
SoC
riscv: sifive_u: Set the minimum number of cpus to 2
riscv: sifive_u: Update PLIC hart topology configuration string
riscv: sifive_u: Update UART base addresses
riscv: sifive_u: Remove the unnecessary include of prci header
riscv: sifive: Rename sifive_prci.{c,h} to sifive_e_prci.{c,h}
riscv: sifive_e: prci: Fix a typo of hfxosccfg register programming
riscv: sifive_e: prci: Update the PRCI register block size
riscv: sifive: Implement PRCI model for FU540
riscv: sifive_u: Generate hfclk and rtcclk nodes
riscv: sifive_u: Add PRCI block to the SoC
riscv: sifive_u: Change UART node name in device tree
riscv: hw: Implement a model for SiFive FU540 OTP
riscv: sifive_u: Instantiate OTP memory with a serial number
riscv: roms: Update default bios for sifive_u machine
riscv: sifive_u: Update UART and ethernet node clock properties
riscv: sifive_u: Generate an aliases node in the device tree
riscv: sifive_u: Fix broken GEM support
riscv: sifive_u: Support loading initramfs
riscv: hw: Remove not needed PLIC properties in device tree
riscv: sifive_e: Drop sifive_mmio_emulate()
riscv: virt: Change create_fdt() to return void
riscv: sifive_u: Update model and compatible strings in device tree
hw/riscv/Makefile.objs | 4 +-
hw/riscv/riscv_hart.c | 75 ++++++--
hw/riscv/sifive_e.c | 27 ++-
hw/riscv/{sifive_prci.c => sifive_e_prci.c} | 16 +-
hw/riscv/sifive_u.c | 186 ++++++++++++++------
hw/riscv/sifive_u_otp.c | 194 +++++++++++++++++++++
hw/riscv/sifive_u_prci.c | 163 +++++++++++++++++
hw/riscv/virt.c | 40 ++---
include/hw/riscv/sifive_cpu.h | 31 ++++
include/hw/riscv/sifive_e.h | 7 +-
.../hw/riscv/{sifive_prci.h => sifive_e_prci.h} | 16 +-
include/hw/riscv/sifive_u.h | 15 +-
include/hw/riscv/sifive_u_otp.h | 90 ++++++++++
include/hw/riscv/sifive_u_prci.h | 100 +++++++++++
pc-bios/opensbi-riscv64-sifive_u-fw_jump.bin | Bin 40968 -> 45064 bytes
roms/Makefile | 4 +-
16 files changed, 828 insertions(+), 140 deletions(-)
rename hw/riscv/{sifive_prci.c => sifive_e_prci.c} (88%)
create mode 100644 hw/riscv/sifive_u_otp.c
create mode 100644 hw/riscv/sifive_u_prci.c
create mode 100644 include/hw/riscv/sifive_cpu.h
rename include/hw/riscv/{sifive_prci.h => sifive_e_prci.h} (80%)
create mode 100644 include/hw/riscv/sifive_u_otp.h
create mode 100644 include/hw/riscv/sifive_u_prci.hSignature · 1 line
2.7.4
PATCH v2 1/28 riscv: hw: Remove superfluous "linux, phandle" property
"linux,phandle" property is optional. Remove all instances in the sifive_u and virt machine device tree.
---
Changes in v2: None
hw/riscv/sifive_u.c | 3 --- hw/riscv/virt.c | 3 --- 2 files changed, 6 deletions(-)
hw/riscv/sifive_u.c +0 -3
@@ -125,7 +125,6 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,qemu_fdt_setprop_string (fdt, nodename,"device_type" ,"cpu" );qemu_fdt_add_subnode (fdt, intc);qemu_fdt_setprop_cell (fdt, intc,"phandle" , cpu_phandle); -qemu_fdt_setprop_cell (fdt, intc,"linux,phandle" , cpu_phandle);qemu_fdt_setprop_string (fdt, intc,"compatible" ,"riscv,cpu-intc" );qemu_fdt_setprop (fdt, intc,"interrupt-controller" ,NULL ,0 );qemu_fdt_setprop_cell (fdt, intc,"#interrupt-cells" ,1 );
@@ -184,7 +183,6 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,qemu_fdt_setprop_cell (fdt, nodename,"riscv,max-priority" ,7 );qemu_fdt_setprop_cell (fdt, nodename,"riscv,ndev" ,0x35 );qemu_fdt_setprop_cells (fdt, nodename,"phandle" , plic_phandle); -qemu_fdt_setprop_cells (fdt, nodename,"linux,phandle" , plic_phandle); plic_phandle =qemu_fdt_get_phandle (fdt, nodename);g_free (cells);g_free (nodename);
@@ -197,7 +195,6 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,qemu_fdt_setprop_cell (fdt, nodename,"clock-frequency" ,SIFIVE_U_GEM_CLOCK_FREQ );qemu_fdt_setprop_cell (fdt, nodename,"phandle" , ethclk_phandle); -qemu_fdt_setprop_cell (fdt, nodename,"linux,phandle" , ethclk_phandle); ethclk_phandle =qemu_fdt_get_phandle (fdt, nodename);g_free (nodename);
hw/riscv/virt.c +0 -3
@@ -170,11 +170,9 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,qemu_fdt_setprop_cell (fdt, nodename,"reg" , cpu);qemu_fdt_setprop_string (fdt, nodename,"device_type" ,"cpu" );qemu_fdt_setprop_cell (fdt, nodename,"phandle" , cpu_phandle); -qemu_fdt_setprop_cell (fdt, nodename,"linux,phandle" , cpu_phandle); intc_phandle = phandle++;qemu_fdt_add_subnode (fdt, intc);qemu_fdt_setprop_cell (fdt, intc,"phandle" , intc_phandle); -qemu_fdt_setprop_cell (fdt, intc,"linux,phandle" , intc_phandle);qemu_fdt_setprop_string (fdt, intc,"compatible" ,"riscv,cpu-intc" );qemu_fdt_setprop (fdt, intc,"interrupt-controller" ,NULL ,0 );qemu_fdt_setprop_cell (fdt, intc,"#interrupt-cells" ,1 );
@@ -250,7 +248,6 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,qemu_fdt_setprop_cell (fdt, nodename,"riscv,max-priority" ,7 );qemu_fdt_setprop_cell (fdt, nodename,"riscv,ndev" ,VIRTIO_NDEV );qemu_fdt_setprop_cells (fdt, nodename,"phandle" , plic_phandle); -qemu_fdt_setprop_cells (fdt, nodename,"linux,phandle" , plic_phandle); plic_phandle =qemu_fdt_get_phandle (fdt, nodename);g_free (cells);g_free (nodename);
Signature · 1 line
2.7.4
PATCH v2 2/28 riscv: hw: Use qemu_fdt_setprop_cell() for property with only 1 cell
In reply to Bin MengSome of the properties only have 1 cell so we should use qemu_fdt_setprop_cell() instead of qemu_fdt_setprop_cells().
---
Changes in v2: None
hw/riscv/sifive_u.c | 16 ++++++++-------- hw/riscv/virt.c | 24 ++++++++++++------------ 2 files changed, 20 insertions(+), 20 deletions(-)
hw/riscv/sifive_u.c +8 -8
@@ -182,7 +182,7 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,qemu_fdt_setprop_string (fdt, nodename,"reg-names" ,"control" );qemu_fdt_setprop_cell (fdt, nodename,"riscv,max-priority" ,7 );qemu_fdt_setprop_cell (fdt, nodename,"riscv,ndev" ,0x35 ); -qemu_fdt_setprop_cells (fdt, nodename,"phandle" , plic_phandle); +qemu_fdt_setprop_cell (fdt, nodename,"phandle" , plic_phandle); plic_phandle =qemu_fdt_get_phandle (fdt, nodename);g_free (cells);g_free (nodename);
@@ -207,20 +207,20 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap, 0x0, memmap[SIFIVE_U_GEM].size);qemu_fdt_setprop_string (fdt, nodename,"reg-names" ,"control" );qemu_fdt_setprop_string (fdt, nodename,"phy-mode" ,"gmii" ); -qemu_fdt_setprop_cells (fdt, nodename,"interrupt-parent" , plic_phandle); -qemu_fdt_setprop_cells (fdt, nodename,"interrupts" ,SIFIVE_U_GEM_IRQ ); +qemu_fdt_setprop_cell (fdt, nodename,"interrupt-parent" , plic_phandle); +qemu_fdt_setprop_cell (fdt, nodename,"interrupts" ,SIFIVE_U_GEM_IRQ );qemu_fdt_setprop_cells (fdt, nodename,"clocks" , ethclk_phandle, ethclk_phandle, ethclk_phandle);qemu_fdt_setprop (fdt, nodename,"clocks-names" , ethclk_names,sizeof (ethclk_names)); -qemu_fdt_setprop_cells (fdt, nodename,"#address-cells" ,1 ); -qemu_fdt_setprop_cells (fdt, nodename,"#size-cells" ,0 ); +qemu_fdt_setprop_cell (fdt, nodename,"#address-cells" ,1 ); +qemu_fdt_setprop_cell (fdt, nodename,"#size-cells" ,0 );g_free (nodename); nodename =g_strdup_printf ("/soc/ethernet@%lx/ethernet-phy@0" , (long )memmap[SIFIVE_U_GEM ].base);qemu_fdt_add_subnode (fdt, nodename); -qemu_fdt_setprop_cells (fdt, nodename,"reg" ,0x0 ); +qemu_fdt_setprop_cell (fdt, nodename,"reg" ,0x0 );g_free (nodename); nodename = g_strdup_printf("/soc/uart@%lx",
@@ -232,8 +232,8 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap, 0x0, memmap[SIFIVE_U_UART0].size);qemu_fdt_setprop_cell (fdt, nodename,"clock-frequency" ,SIFIVE_U_CLOCK_FREQ /2 ); -qemu_fdt_setprop_cells (fdt, nodename,"interrupt-parent" , plic_phandle); -qemu_fdt_setprop_cells (fdt, nodename,"interrupts" ,SIFIVE_U_UART0_IRQ ); +qemu_fdt_setprop_cell (fdt, nodename,"interrupt-parent" , plic_phandle); +qemu_fdt_setprop_cell (fdt, nodename,"interrupts" ,SIFIVE_U_UART0_IRQ );qemu_fdt_add_subnode (fdt,"/chosen" );qemu_fdt_setprop_string (fdt,"/chosen" ,"stdout-path" , nodename);
hw/riscv/virt.c +12 -12
@@ -233,8 +233,8 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap, nodename =g_strdup_printf ("/soc/interrupt-controller@%lx" , (long )memmap[VIRT_PLIC ].base);qemu_fdt_add_subnode (fdt, nodename); -qemu_fdt_setprop_cells (fdt, nodename,"#address-cells" , -FDT_PLIC_ADDR_CELLS ); +qemu_fdt_setprop_cell (fdt, nodename,"#address-cells" , +FDT_PLIC_ADDR_CELLS );qemu_fdt_setprop_cell (fdt, nodename,"#interrupt-cells" ,FDT_PLIC_INT_CELLS );qemu_fdt_setprop_string (fdt, nodename,"compatible" ,"riscv,plic0" );
@@ -247,7 +247,7 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,qemu_fdt_setprop_string (fdt, nodename,"reg-names" ,"control" );qemu_fdt_setprop_cell (fdt, nodename,"riscv,max-priority" ,7 );qemu_fdt_setprop_cell (fdt, nodename,"riscv,ndev" ,VIRTIO_NDEV ); -qemu_fdt_setprop_cells (fdt, nodename,"phandle" , plic_phandle); +qemu_fdt_setprop_cell (fdt, nodename,"phandle" , plic_phandle); plic_phandle =qemu_fdt_get_phandle (fdt, nodename);g_free (cells);g_free (nodename);
@@ -260,19 +260,19 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,qemu_fdt_setprop_cells (fdt, nodename,"reg" ,0x0 , memmap[VIRT_VIRTIO ].base + i * memmap[VIRT_VIRTIO ].size,0x0 , memmap[VIRT_VIRTIO ].size); -qemu_fdt_setprop_cells (fdt, nodename,"interrupt-parent" , plic_phandle); -qemu_fdt_setprop_cells (fdt, nodename,"interrupts" ,VIRTIO_IRQ + i); +qemu_fdt_setprop_cell (fdt, nodename,"interrupt-parent" , plic_phandle); +qemu_fdt_setprop_cell (fdt, nodename,"interrupts" ,VIRTIO_IRQ + i);g_free (nodename); } nodename =g_strdup_printf ("/soc/pci@%lx" , (long ) memmap[VIRT_PCIE_ECAM ].base);qemu_fdt_add_subnode (fdt, nodename); -qemu_fdt_setprop_cells (fdt, nodename,"#address-cells" , -FDT_PCI_ADDR_CELLS ); -qemu_fdt_setprop_cells (fdt, nodename,"#interrupt-cells" , -FDT_PCI_INT_CELLS ); -qemu_fdt_setprop_cells (fdt, nodename,"#size-cells" ,0x2 ); +qemu_fdt_setprop_cell (fdt, nodename,"#address-cells" , +FDT_PCI_ADDR_CELLS ); +qemu_fdt_setprop_cell (fdt, nodename,"#interrupt-cells" , +FDT_PCI_INT_CELLS ); +qemu_fdt_setprop_cell (fdt, nodename,"#size-cells" ,0x2 );qemu_fdt_setprop_string (fdt, nodename,"compatible" ,"pci-host-ecam-generic" );qemu_fdt_setprop_string (fdt, nodename,"device_type" ,"pci" );
@@ -309,8 +309,8 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,0x0 , memmap[VIRT_UART0 ].base, 0x0, memmap[VIRT_UART0].size);qemu_fdt_setprop_cell (fdt, nodename,"clock-frequency" ,3686400 ); -qemu_fdt_setprop_cells (fdt, nodename,"interrupt-parent" , plic_phandle); -qemu_fdt_setprop_cells (fdt, nodename,"interrupts" ,UART0_IRQ ); +qemu_fdt_setprop_cell (fdt, nodename,"interrupt-parent" , plic_phandle); +qemu_fdt_setprop_cell (fdt, nodename,"interrupts" ,UART0_IRQ );qemu_fdt_add_subnode (fdt,"/chosen" );qemu_fdt_setprop_string (fdt,"/chosen" ,"stdout-path" , nodename);
Signature · 1 line
2.7.4
PATCH v2 3/28 riscv: Add a sifive_cpu.h to include both E and U cpu type defines
In reply to Bin MengGroup SiFive E and U cpu type defines into one header file.
---
Changes in v2: None
include/hw/riscv/sifive_cpu.h | 31 +++++++++++++++++++++++++++++++ include/hw/riscv/sifive_e.h | 7 +------ include/hw/riscv/sifive_u.h | 7 +------ 3 files changed, 33 insertions(+), 12 deletions(-) create mode 100644 include/hw/riscv/sifive_cpu.h
include/hw/riscv/sifive_cpu.h new file +31 -0
@@ -0,0 +1,31 @@ +/* +* SiFive CPU types +* +* Copyright (c) 2017 SiFive, Inc. +* Copyright (c) 2019 Bin Meng <[email protected]> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms and conditions of the GNU General Public License, +* version 2 or later, as published by the Free Software Foundation. +* +* This program is distributed in the hope it will be useful, but WITHOUT +* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or +* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for +* more details. +* +* You should have received a copy of the GNU General Public License along with +* this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef HW_SIFIVE_CPU_H +#define HW_SIFIVE_CPU_H + +#if defined(TARGET_RISCV32 ) +#define SIFIVE_E_CPU TYPE_RISCV_CPU_SIFIVE_E31 +#define SIFIVE_U_CPU TYPE_RISCV_CPU_SIFIVE_U34 +#elif defined(TARGET_RISCV64 ) +#define SIFIVE_E_CPU TYPE_RISCV_CPU_SIFIVE_E51 +#define SIFIVE_U_CPU TYPE_RISCV_CPU_SIFIVE_U54 +#endif + +#endif /* HW_SIFIVE_CPU_H */
include/hw/riscv/sifive_e.h +1 -6
@@ -19,6 +19,7 @@#ifndef HW_SIFIVE_E_H #define HW_SIFIVE_E_H +#include "hw/riscv/sifive_cpu.h" #include "hw/riscv/sifive_gpio.h" #define TYPE_RISCV_E_SOC "riscv.sifive.e.soc"
@@ -83,10 +84,4 @@ enum {#define SIFIVE_E_PLIC_CONTEXT_BASE 0x200000#define SIFIVE_E_PLIC_CONTEXT_STRIDE 0x1000 -#if defined(TARGET_RISCV32 ) -#define SIFIVE_E_CPU TYPE_RISCV_CPU_SIFIVE_E31 -#elif defined(TARGET_RISCV64 ) -#define SIFIVE_E_CPU TYPE_RISCV_CPU_SIFIVE_E51 -#endif -#endif
include/hw/riscv/sifive_u.h +1 -6
@@ -20,6 +20,7 @@#define HW_SIFIVE_U_H #include "hw/net/cadence_gem.h" +#include "hw/riscv/sifive_cpu.h" #define TYPE_RISCV_U_SOC "riscv.sifive.u.soc"#define RISCV_U_SOC (obj) \
@@ -77,10 +78,4 @@ enum {#define SIFIVE_U_PLIC_CONTEXT_BASE 0x200000#define SIFIVE_U_PLIC_CONTEXT_STRIDE 0x1000 -#if defined(TARGET_RISCV32 ) -#define SIFIVE_U_CPU TYPE_RISCV_CPU_SIFIVE_U34 -#elif defined(TARGET_RISCV64 ) -#define SIFIVE_U_CPU TYPE_RISCV_CPU_SIFIVE_U54 -#endif -#endif
Signature · 1 line
2.7.4
Re: [Qemu-devel] [PATCH v2 03/28] riscv: Add a sifive_cpu.h to include both E and U cpu type defines
Quoted 4 lines · Bin Meng
Group SiFive E and U cpu type defines into one header file.
Signed-off-by Bin Meng <[email protected]>Reviewed-by Alistair Francis <[email protected]>
Quoted 94 lines
---
Changes in v2: None
include/hw/riscv/sifive_cpu.h | 31 +++++++++++++++++++++++++++++++ include/hw/riscv/sifive_e.h | 7 +------ include/hw/riscv/sifive_u.h | 7 +------ 3 files changed, 33 insertions(+), 12 deletions(-) create mode 100644 include/hw/riscv/sifive_cpu.hinclude/hw/riscv/sifive_cpu.h new file +31
-0@@ -0,0 +1,31 @@ +/* +* SiFive CPU types +* +* Copyright (c) 2017 SiFive, Inc. +* Copyright (c) 2019 Bin Meng <[email protected]> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms and conditions of the GNU General Public License, +* version 2 or later, as published by the Free Software Foundation. +* +* This program is distributed in the hope it will be useful, but WITHOUT +* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or +* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for +* more details. +* +* You should have received a copy of the GNU General Public License along with +* this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef HW_SIFIVE_CPU_H +#define HW_SIFIVE_CPU_H + +#if defined(TARGET_RISCV32 ) +#define SIFIVE_E_CPU TYPE_RISCV_CPU_SIFIVE_E31 +#define SIFIVE_U_CPU TYPE_RISCV_CPU_SIFIVE_U34 +#elif defined(TARGET_RISCV64 ) +#define SIFIVE_E_CPU TYPE_RISCV_CPU_SIFIVE_E51 +#define SIFIVE_U_CPU TYPE_RISCV_CPU_SIFIVE_U54 +#endif + +#endif /* HW_SIFIVE_CPU_H */ include/hw/riscv/sifive_e.h +1
-6@@ -19,6 +19,7 @@#ifndef HW_SIFIVE_E_H #define HW_SIFIVE_E_H +#include "hw/riscv/sifive_cpu.h" #include "hw/riscv/sifive_gpio.h" #define TYPE_RISCV_E_SOC "riscv.sifive.e.soc"@@ -83,10 +84,4 @@ enum {#define SIFIVE_E_PLIC_CONTEXT_BASE 0x200000#define SIFIVE_E_PLIC_CONTEXT_STRIDE 0x1000 -#if defined(TARGET_RISCV32 ) -#define SIFIVE_E_CPU TYPE_RISCV_CPU_SIFIVE_E31 -#elif defined(TARGET_RISCV64 ) -#define SIFIVE_E_CPU TYPE_RISCV_CPU_SIFIVE_E51 -#endif -#endif include/hw/riscv/sifive_u.h +1
-6@@ -20,6 +20,7 @@#define HW_SIFIVE_U_H #include "hw/net/cadence_gem.h" +#include "hw/riscv/sifive_cpu.h" #define TYPE_RISCV_U_SOC "riscv.sifive.u.soc"#define RISCV_U_SOC (obj) \@@ -77,10 +78,4 @@ enum {#define SIFIVE_U_PLIC_CONTEXT_BASE 0x200000#define SIFIVE_U_PLIC_CONTEXT_STRIDE 0x1000 -#if defined(TARGET_RISCV32 ) -#define SIFIVE_U_CPU TYPE_RISCV_CPU_SIFIVE_U34 -#elif defined(TARGET_RISCV64 ) -#define SIFIVE_U_CPU TYPE_RISCV_CPU_SIFIVE_U54 -#endif -#endif
PATCH v2 4/28 riscv: hart: Extract hart realize to a separate routine
In reply to Bin MengCurrently riscv_harts_realize() creates all harts based on the same cpu type given in the hart array property. With current implementation it can only create symmetric harts. Exact the hart realize to a separate routine in preparation for supporting heterogeneous hart arrays.
---
Changes in v2: None
hw/riscv/riscv_hart.c | 31 +++++++++++++++++++------------ 1 file changed, 19 insertions(+), 12 deletions(-)
hw/riscv/riscv_hart.c +19 -12
@@ -37,26 +37,33 @@ static void riscv_harts_cpu_reset(void *opaque)cpu_reset (CPU (cpu)); } +static void riscv_hart_realize (RISCVHartArrayState *s,int hart, +char *cpu_type,Error **errp) +{ +Error *err =NULL ; + +object_initialize_child (OBJECT (s),"harts[*]" , &s->harts[hart], +sizeof (RISCVCPU ), cpu_type, + &error_abort,NULL ); + s->harts[hart].env.mhartid = hart; +qemu_register_reset (riscv_harts_cpu_reset, &s->harts[hart]); +object_property_set_bool (OBJECT (&s->harts[hart]), true, +"realized" , &err); +if (err) { +error_propagate (errp, err); +return ; + } +} +static void riscv_harts_realize (DeviceState *dev,Error **errp) {RISCVHartArrayState *s =RISCV_HART_ARRAY (dev); -Error *err =NULL ;int n; s->harts =g_new0 (RISCVCPU , s->num_harts);for (n =0 ; n < s->num_harts; n++) { -object_initialize_child (OBJECT (s),"harts[*]" , &s->harts[n], -sizeof (RISCVCPU ), s->cpu_type, - &error_abort,NULL ); - s->harts[n].env.mhartid = n; -qemu_register_reset (riscv_harts_cpu_reset, &s->harts[n]); -object_property_set_bool (OBJECT (&s->harts[n]), true, -"realized" , &err); -if (err) { -error_propagate (errp, err); -return ; - } +riscv_hart_realize (s, n, s->cpu_type, errp); } }
Signature · 1 line
2.7.4
PATCH v2 5/28 riscv: hart: Support heterogeneous harts population
In reply to Bin MengAt present we only allow symmetric harts to be created. In order to support heterogeneous harts like SiFive FU540, update hart array's "cpu-type" property to allow cpu type to be set per hart, separated by delimiter ",". The frist cpu type before the delimiter is assigned to hart 0, and the second cpu type before delimiter is assigned to hart 1, and so on.
If the total number of cpu types supplied in "cpu-type" property is less than number of maximum harts, the last cpu type in the property will be used to populate remaining harts.
---
Changes in v2: None
hw/riscv/riscv_hart.c | 48 +++++++++++++++++++++++++++++++++++++++++++++--- 1 file changed, 45 insertions(+), 3 deletions(-)
hw/riscv/riscv_hart.c +45 -3
@@ -58,13 +58,55 @@ static void riscv_hart_realize(RISCVHartArrayState *s, int hart,static void riscv_harts_realize (DeviceState *dev,Error **errp) {RISCVHartArrayState *s =RISCV_HART_ARRAY (dev); -int n; +char *cpu_types; +char *first_type, *last_type, *tmp_type; +int n =0 ; s->harts =g_new0 (RISCVCPU , s->num_harts); -for (n =0 ; n < s->num_harts; n++) { -riscv_hart_realize (s, n, s->cpu_type, errp); +/* we should not touch the original s->cpu_type */ + cpu_types =g_strdup (s->cpu_type); + +/* +* Expect s->cpu_type property was initialized this way: +* +* "cpu-type-a": symmetric harts +* "cpu-type-a,cpu-type-b,cpu-type-c": heterogeneous harts +* +* For heterogeneous harts, hart cpu types are separated by delimiter ",". +* The frist cpu type before the delimiter is assigned to hart 0, and the +* second cpu type before delimiter is assigned to hart 1, and so on. +* +* If the total number of cpu types is less than s->num_harts, the last +* cpu type in s->cpu_type will be used to populate remaining harts. +*/ + + first_type =strtok (cpu_types,"," ); +riscv_hart_realize (s, n++, first_type, errp); + tmp_type =strtok (NULL ,"," ); +if (!tmp_type) { +/* symmetric harts */ +for (; n < s->num_harts; n++) { +riscv_hart_realize (s, n, first_type, errp); + } + }else { +/* heterogeneous harts */ +while (tmp_type) { +if (n >= s->num_harts) { +break ; + } +riscv_hart_realize (s, n++, tmp_type, errp); + last_type = tmp_type; + tmp_type =strtok (NULL ,"," ); + } + +/* populate remaining harts using the last cpu type in s->cpu_type */ +for (; n < s->num_harts; n++) { +riscv_hart_realize (s, n, last_type, errp); + } } + +g_free (cpu_types); }static void riscv_harts_class_init (ObjectClass *klass,void *data)
Signature · 1 line
2.7.4
PATCH v2 6/28 riscv: sifive_u: Update hart configuration to reflect the real FU540 SoC
In reply to Bin MengThe FU540-C000 includes a 64-bit E51 RISC-V core and four 64-bit U54 RISC-V cores. Currently the sifive_u machine only populates 4 U54 cores. Update the max cpu number to 5 to reflect the real hardware, and pass "cpu-type" to populate heterogeneous harts.
The cpu nodes in the generated DTS have been updated as well.
---
Changes in v2:
- fixed the "interrupts-extended" property size
hw/riscv/sifive_u.c | 40 +++++++++++++++++++++++++++++----------- 1 file changed, 29 insertions(+), 11 deletions(-)
hw/riscv/sifive_u.c +29 -11
@@ -10,7 +10,8 @@* 1) CLINT (Core Level Interruptor) * 2) PLIC (Platform Level Interrupt Controller) * -* This board currently uses a hardcoded devicetree that indicates one hart. +* This board currently generates devicetree dynamically that indicates at most +* five harts. * * This program is free software; you can redistribute it and/or modify it * under the terms and conditions of the GNU General Public License,
@@ -26,6 +27,7 @@*/ #include "qemu/osdep.h" +#include "qemu/cutils.h" #include "qemu/log.h" #include "qemu/error-report.h" #include "qapi/error.h"
@@ -117,7 +119,10 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,qemu_fdt_add_subnode (fdt, nodename);qemu_fdt_setprop_cell (fdt, nodename,"clock-frequency" ,SIFIVE_U_CLOCK_FREQ ); -qemu_fdt_setprop_string (fdt, nodename,"mmu-type" ,"riscv,sv48" ); +/* cpu 0 is the management hart that does not have mmu */ +if (cpu !=0 ) { +qemu_fdt_setprop_string (fdt, nodename,"mmu-type" ,"riscv,sv48" ); + }qemu_fdt_setprop_string (fdt, nodename,"riscv,isa" , isa);qemu_fdt_setprop_string (fdt, nodename,"compatible" ,"riscv" );qemu_fdt_setprop_string (fdt, nodename,"status" ,"okay" );
@@ -157,15 +162,21 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,g_free (nodename); plic_phandle = phandle++; - cells =g_new0 (uint32_t, s->soc.cpus.num_harts *4 ); + cells =g_new0 (uint32_t, s->soc.cpus.num_harts *4 -2 );for (cpu =0 ; cpu < s->soc.cpus.num_harts; cpu++) { nodename =g_strdup_printf ("/cpus/cpu@%d/interrupt-controller" , cpu);uint32_t intc_phandle =qemu_fdt_get_phandle (fdt, nodename); - cells[cpu *4 +0 ] =cpu_to_be32 (intc_phandle); - cells[cpu *4 +1 ] =cpu_to_be32 (IRQ_M_EXT ); - cells[cpu *4 +2 ] =cpu_to_be32 (intc_phandle); - cells[cpu *4 +3 ] =cpu_to_be32 (IRQ_S_EXT ); +/* cpu 0 is the management hart that does not have S-mode */ +if (cpu ==0 ) { + cells[0 ] =cpu_to_be32 (intc_phandle); + cells[1 ] =cpu_to_be32 (IRQ_M_EXT ); + }else { + cells[cpu *4 -2 ] =cpu_to_be32 (intc_phandle); + cells[cpu *4 -1 ] =cpu_to_be32 (IRQ_M_EXT ); + cells[cpu *4 +0 ] =cpu_to_be32 (intc_phandle); + cells[cpu *4 +1 ] =cpu_to_be32 (IRQ_S_EXT ); + }g_free (nodename); } nodename = g_strdup_printf("/soc/interrupt-controller@%lx",
@@ -175,7 +186,7 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,qemu_fdt_setprop_string (fdt, nodename,"compatible" ,"riscv,plic0" );qemu_fdt_setprop (fdt, nodename,"interrupt-controller" ,NULL ,0 );qemu_fdt_setprop (fdt, nodename,"interrupts-extended" , - cells, s->soc.cpus.num_harts *sizeof (uint32_t ) *4 ); + cells, (s->soc.cpus.num_harts *4 -2 ) *sizeof (uint32_t ));qemu_fdt_setprop_cells (fdt, nodename,"reg" ,0x0 , memmap[SIFIVE_U_PLIC ].base,0x0 , memmap[SIFIVE_U_PLIC ].size);
@@ -315,10 +326,16 @@ static void riscv_sifive_u_soc_init(Object *obj) {MachineState *ms =MACHINE (qdev_get_machine ());SiFiveUSoCState *s =RISCV_U_SOC (obj); +char cpu_type[64 ]; + +/* create cpu type representing SiFive FU540 SoC */ +pstrcpy (cpu_type,sizeof (cpu_type),SIFIVE_E_CPU ); +pstrcat (cpu_type,sizeof (cpu_type),"," ); +pstrcat (cpu_type,sizeof (cpu_type),SIFIVE_U_CPU );object_initialize_child (obj,"cpus" , &s->cpus,sizeof (s->cpus),TYPE_RISCV_HART_ARRAY , &error_abort,NULL ); -object_property_set_str (OBJECT (&s->cpus),SIFIVE_U_CPU ,"cpu-type" , +object_property_set_str (OBJECT (&s->cpus), cpu_type,"cpu-type" , &error_abort);object_property_set_int (OBJECT (&s->cpus), ms->smp.cpus,"num-harts" , &error_abort);
@@ -407,10 +424,11 @@ static void riscv_sifive_u_machine_init(MachineClass *mc) { mc->desc ="RISC-V Board compatible with SiFive U SDK" ; mc->init = riscv_sifive_u_init; -/* The real hardware has 5 CPUs, but one of them is a small embedded power +/* +* The real hardware has 5 CPUs, but one of them is a small embedded power * management CPU. */ - mc->max_cpus =4 ; + mc->max_cpus =5 ; }DEFINE_MACHINE ("sifive_u" , riscv_sifive_u_machine_init)
Signature · 1 line
2.7.4
PATCH v2 7/28 riscv: sifive_u: Set the minimum number of cpus to 2
In reply to Bin MengIt is not useful if we only have one management CPU.
---
Changes in v2:
- update the file header to indicate at least 2 harts are created
hw/riscv/sifive_u.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)
hw/riscv/sifive_u.c +4 -2
@@ -10,8 +10,8 @@* 1) CLINT (Core Level Interruptor) * 2) PLIC (Platform Level Interrupt Controller) * -* This board currently generates devicetree dynamically that indicates at most -* five harts. +* This board currently generates devicetree dynamically that indicates at least +* two harts and up to five harts. * * This program is free software; you can redistribute it and/or modify it * under the terms and conditions of the GNU General Public License,
@@ -429,6 +429,8 @@ static void riscv_sifive_u_machine_init(MachineClass *mc)* management CPU. */ mc->max_cpus =5 ; +/* It is not useful if we only have one management CPU */ + mc->min_cpus =2 ; }DEFINE_MACHINE ("sifive_u" , riscv_sifive_u_machine_init)
Signature · 1 line
2.7.4
Re: [Qemu-devel] [PATCH v2 07/28] riscv: sifive_u: Set the minimum number of cpus to 2
Quoted 28 lines · Bin Meng
It is not useful if we only have one management CPU.
Signed-off-by Bin Meng <[email protected]>---
Changes in v2:
- update the file header to indicate at least 2 harts are createdhw/riscv/sifive_u.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)hw/riscv/sifive_u.c +2
-2@@ -10,8 +10,8 @@* 1) CLINT (Core Level Interruptor) * 2) PLIC (Platform Level Interrupt Controller) * -* This board currently generates devicetree dynamically that indicates at most -* five harts. +* This board currently generates devicetree dynamically that indicates at least +* two harts and up to five harts. * * This program is free software; you can redistribute it and/or modify it * under the terms and conditions of the GNU General Public License,
hw/riscv/sifive_u.c static void riscv_sifive_u_machine_init(MachineClass *mc) · line 431
Quoted 3 lines
hw/riscv/sifive_u.c +0
-0@@ -429,6 +429,8 @@ static void riscv_sifive_u_machine_init(MachineClass *mc)* management CPU. */ mc->max_cpus =5 ;
I'm confuse this patch does not apply on top of v4.1.0-rc4.
Using #define makes these comments redundant, something like:
#define MANAGEMENT_CPU_COUNT 1
#define COMPUTE_CPU_COUNT 4
then you could use
max_cpus = MANAGEMENT_CPU_COUNT + COMPUTE_CPU_COUNT
and
min_cpus = MANAGEMENT_CPU_COUNT + 1.
Quoted 6 lines
hw/riscv/sifive_u.c +2
-0+/* It is not useful if we only have one management CPU */ + mc->min_cpus =2 ; }DEFINE_MACHINE ("sifive_u" , riscv_sifive_u_machine_init)
Re: [Qemu-devel] [PATCH v2 07/28] riscv: sifive_u: Set the minimum number of cpus to 2
Quoted 27 lines · Philippe Mathieu-Daudé
Quoted 25 lines · Bin Meng
It is not useful if we only have one management CPU.
Signed-off-by Bin Meng <[email protected]>---
Changes in v2:
- update the file header to indicate at least 2 harts are createdhw/riscv/sifive_u.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)hw/riscv/sifive_u.c +2
-2@@ -10,8 +10,8 @@* 1) CLINT (Core Level Interruptor) * 2) PLIC (Platform Level Interrupt Controller) * -* This board currently generates devicetree dynamically that indicates at most -* five harts. +* This board currently generates devicetree dynamically that indicates at least +* two harts and up to five harts. *
Quoted 9 lines
hw/riscv/sifive_u.c static void riscv_sifive_u_machine_init(MachineClass *mc) · line 431
Quoted 6 lines
hw/riscv/sifive_u.c +0
-0* This program is free software; you can redistribute it and/or modify it * under the terms and conditions of the GNU General Public License, @@ -429,6 +429,8 @@ static void riscv_sifive_u_machine_init(MachineClass *mc)* management CPU. */ mc->max_cpus =5 ;I'm confuse this patch does not apply on top of v4.1.0-rc4.
I suspect you need apply the whole series, not this single one due to patch dependencies in this series?
Quoted 5 lines
Using #define makes these comments redundant, something like:
#define
MANAGEMENT_CPU_COUNT1
#defineCOMPUTE_CPU_COUNT4
Quoted 8 lines
then you could use
max_cpus=MANAGEMENT_CPU_COUNT+COMPUTE_CPU_COUNTand
min_cpus=MANAGEMENT_CPU_COUNT+ 1.
Good idea! I will change that in the next version. Thanks!
Regards,
Bin
PATCH v2 8/28 riscv: sifive_u: Update PLIC hart topology configuration string
In reply to Bin MengWith heterogeneous harts config, the PLIC hart topology configuration string are "M,MS,.." because of the monitor hart #0.
---
Changes in v2: None
hw/riscv/sifive_u.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)
hw/riscv/sifive_u.c +4 -3
@@ -373,10 +373,11 @@ static void riscv_sifive_u_soc_realize(DeviceState *dev, Error **errp) plic_hart_config =g_malloc0 (plic_hart_config_len);for (i =0 ; i < ms->smp.cpus; i++) {if (i !=0 ) { -strncat (plic_hart_config,"," , plic_hart_config_len); +strncat (plic_hart_config,"," SIFIVE_U_PLIC_HART_CONFIG , + plic_hart_config_len); + }else { +strncat (plic_hart_config,"M" , plic_hart_config_len); } -strncat (plic_hart_config,SIFIVE_U_PLIC_HART_CONFIG , - plic_hart_config_len); plic_hart_config_len -= (strlen (SIFIVE_U_PLIC_HART_CONFIG ) +1 ); }
Signature · 1 line
2.7.4
PATCH v2 9/28 riscv: sifive_u: Update UART base addresses
In reply to Bin MengThis updates the UART base address to match the hardware.
---
Changes in v2: None
hw/riscv/sifive_u.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
hw/riscv/sifive_u.c +2 -2
@@ -61,8 +61,8 @@ static const struct MemmapEntry { [SIFIVE_U_MROM] = { 0x1000, 0x11000 }, [SIFIVE_U_CLINT] = { 0x2000000, 0x10000 }, [SIFIVE_U_PLIC] = { 0xc000000, 0x4000000 }, - [SIFIVE_U_UART0] = { 0x10013000, 0x1000 }, - [SIFIVE_U_UART1] = { 0x10023000, 0x1000 }, + [SIFIVE_U_UART0] = { 0x10010000, 0x1000 }, + [SIFIVE_U_UART1] = { 0x10011000, 0x1000 }, [SIFIVE_U_DRAM] = { 0x80000000, 0x0 }, [SIFIVE_U_GEM] = { 0x100900FC, 0x2000 }, };
Signature · 1 line
2.7.4
Re: [Qemu-devel] [PATCH v2 09/28] riscv: sifive_u: Update UART base addresses
Quoted 28 lines · Bin Meng
This updates the UART base address to match the hardware.
Signed-off-by Bin Meng <[email protected]>Reviewed-by Jonathan Behrens <[email protected]>Acked-by Alistair Francis <[email protected]>---
Changes in v2: None
hw/riscv/sifive_u.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)hw/riscv/sifive_u.c +2
-3@@ -61,8 +61,8 @@ static const struct MemmapEntry { [SIFIVE_U_MROM] = { 0x1000, 0x11000 }, [SIFIVE_U_CLINT] = { 0x2000000, 0x10000 }, [SIFIVE_U_PLIC] = { 0xc000000, 0x4000000 }, - [SIFIVE_U_UART0] = { 0x10013000, 0x1000 }, - [SIFIVE_U_UART1] = { 0x10023000, 0x1000 }, + [SIFIVE_U_UART0] = { 0x10010000, 0x1000 }, + [SIFIVE_U_UART1] = { 0x10011000, 0x1000 }, [SIFIVE_U_DRAM] = { 0x80000000, 0x0 }, [SIFIVE_U_GEM] = { 0x100900FC, 0x2000 }, }; --
Quoted 4 lines
2.7.4
By the way, OpenSBI also needs a patch to fix the same problem.
Re: [Qemu-devel] [PATCH v2 09/28] riscv: sifive_u: Update UART base addresses
Quoted 30 lines · Chih-Min Chao
Quoted 26 lines · Bin Meng
This updates the UART base address to match the hardware.
Signed-off-by Bin Meng <[email protected]>Reviewed-by Jonathan Behrens <[email protected]>Acked-by Alistair Francis <[email protected]>---
Changes in v2: None
hw/riscv/sifive_u.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)hw/riscv/sifive_u.c +2
-2@@ -61,8 +61,8 @@ static const struct MemmapEntry { [SIFIVE_U_MROM] = { 0x1000, 0x11000 }, [SIFIVE_U_CLINT] = { 0x2000000, 0x10000 }, [SIFIVE_U_PLIC] = { 0xc000000, 0x4000000 }, - [SIFIVE_U_UART0] = { 0x10013000, 0x1000 }, - [SIFIVE_U_UART1] = { 0x10023000, 0x1000 }, + [SIFIVE_U_UART0] = { 0x10010000, 0x1000 }, + [SIFIVE_U_UART1] = { 0x10011000, 0x1000 }, [SIFIVE_U_DRAM] = { 0x80000000, 0x0 },
Quoted 9 lines
Quoted 6 lines
hw/riscv/sifive_u.c +0
-1[SIFIVE_U_GEM] = { 0x100900FC, 0x2000 }, }; --2.7.4
By the way, OpenSBI also needs a patch to fix the same problem.
No, with this series, sifive_u is not a special target any more and sifive/fu540 should be set to PLATFORM in the OpenSBI build for the 'sifive_u' machine.
I will send a patch to OpenSBI to drop the 'sifive_u' support.
Quoted 1 line
Reviewed-by Chih-Min Chao <[email protected]>
Regards,
Bin
PATCH v2 10/28 riscv: sifive_u: Remove the unnecessary include of prci header
In reply to Bin Mengsifive_u machine does not use PRCI as of today. Remove the prci header inclusion.
---
Changes in v2: None
hw/riscv/sifive_u.c | 1 - 1 file changed, 1 deletion(-)
hw/riscv/sifive_u.c +0 -1
@@ -41,7 +41,6 @@#include "hw/riscv/sifive_plic.h" #include "hw/riscv/sifive_clint.h" #include "hw/riscv/sifive_uart.h" -#include "hw/riscv/sifive_prci.h" #include "hw/riscv/sifive_u.h" #include "hw/riscv/boot.h" #include "chardev/char.h"
Signature · 1 line
2.7.4
PATCH v2 11/28 riscv: sifive: Rename sifive_prci.{c, h} to sifive_e_prci.{c, h}
In reply to Bin MengCurrent SiFive PRCI model only works with sifive_e machine, as it only emulates registers or PRCI block in the FE310 SoC.
Rename the file name to make it clear that it is for sifive_e.
---
Changes in v2: None
hw/riscv/Makefile.objs | 2 +-
hw/riscv/sifive_e.c | 4 ++--
hw/riscv/{sifive_prci.c => sifive_e_prci.c} | 14 +++++++-------
include/hw/riscv/{sifive_prci.h => sifive_e_prci.h} | 14 +++++++-------
4 files changed, 17 insertions(+), 17 deletions(-)
rename hw/riscv/{sifive_prci.c => sifive_e_prci.c} (90%)
rename include/hw/riscv/{sifive_prci.h => sifive_e_prci.h} (82%)hw/riscv/Makefile.objs +1 -1
@@ -2,9 +2,9 @@ obj-y += boot.o obj-$(CONFIG_SPIKE) += riscv_htif.o obj-$(CONFIG_HART) += riscv_hart.o obj-$(CONFIG_SIFIVE_E) += sifive_e.o +obj-$(CONFIG_SIFIVE_E) += sifive_e_prci.o obj-$(CONFIG_SIFIVE) += sifive_clint.o obj-$(CONFIG_SIFIVE) += sifive_gpio.o -obj-$(CONFIG_SIFIVE) += sifive_prci.o obj-$(CONFIG_SIFIVE) += sifive_plic.o obj-$(CONFIG_SIFIVE) += sifive_test.o obj-$(CONFIG_SIFIVE_U) += sifive_u.o
hw/riscv/sifive_e.c +2 -2
@@ -41,9 +41,9 @@#include "hw/riscv/riscv_hart.h" #include "hw/riscv/sifive_plic.h" #include "hw/riscv/sifive_clint.h" -#include "hw/riscv/sifive_prci.h" #include "hw/riscv/sifive_uart.h" #include "hw/riscv/sifive_e.h" +#include "hw/riscv/sifive_e_prci.h" #include "hw/riscv/boot.h" #include "chardev/char.h" #include "sysemu/arch_init.h"
@@ -174,7 +174,7 @@ static void riscv_sifive_e_soc_realize(DeviceState *dev, Error **errp) SIFIVE_SIP_BASE, SIFIVE_TIMECMP_BASE, SIFIVE_TIME_BASE);sifive_mmio_emulate (sys_mem,"riscv.sifive.e.aon" , memmap[SIFIVE_E_AON ].base, memmap[SIFIVE_E_AON ].size); -sifive_prci_create (memmap[SIFIVE_E_PRCI ].base); +sifive_e_prci_create (memmap[SIFIVE_E_PRCI ].base);/* GPIO */
hw/riscv/sifive_e_prci.c renamed from hw/riscv/sifive_prci.c +7 -7
@@ -1,5 +1,5 @@/* -* QEMU SiFive PRCI (Power, Reset, Clock, Interrupt) +* QEMU SiFive E PRCI (Power, Reset, Clock, Interrupt) * * Copyright (c) 2017 SiFive, Inc. *
@@ -22,7 +22,7 @@#include "hw/sysbus.h" #include "qemu/module.h" #include "target/riscv/cpu.h" -#include "hw/riscv/sifive_prci.h" +#include "hw/riscv/sifive_e_prci.h" static uint64_t sifive_prci_read (void *opaque,hwaddr addr,unsigned int size) {
@@ -82,10 +82,10 @@ static const MemoryRegionOps sifive_prci_ops = {static void sifive_prci_init (Object *obj) { -SiFivePRCIState *s =SIFIVE_PRCI (obj); +SiFivePRCIState *s =SIFIVE_E_PRCI (obj);memory_region_init_io (&s->mmio, obj, &sifive_prci_ops, s, -TYPE_SIFIVE_PRCI ,0x8000 ); +TYPE_SIFIVE_E_PRCI ,0x8000 );sysbus_init_mmio (SYS_BUS_DEVICE (obj), &s->mmio); s->hfrosccfg = (SIFIVE_PRCI_HFROSCCFG_RDY |SIFIVE_PRCI_HFROSCCFG_EN );
@@ -97,7 +97,7 @@ static void sifive_prci_init(Object *obj) }static const TypeInfo sifive_prci_info = { - .name =TYPE_SIFIVE_PRCI , + .name =TYPE_SIFIVE_E_PRCI , .parent =TYPE_SYS_BUS_DEVICE , .instance_size =sizeof (SiFivePRCIState), .instance_init = sifive_prci_init,
@@ -114,9 +114,9 @@ type_init(sifive_prci_register_types)/* * Create PRCI device. */ -DeviceState *sifive_prci_create (hwaddr addr) +DeviceState *sifive_e_prci_create (hwaddr addr) { -DeviceState *dev =qdev_create (NULL ,TYPE_SIFIVE_PRCI ); +DeviceState *dev =qdev_create (NULL ,TYPE_SIFIVE_E_PRCI );qdev_init_nofail (dev);sysbus_mmio_map (SYS_BUS_DEVICE (dev),0 , addr);return dev;
include/hw/riscv/sifive_e_prci.h renamed from include/hw/riscv/sifive_prci.h +7 -7
@@ -1,5 +1,5 @@/* -* QEMU SiFive PRCI (Power, Reset, Clock, Interrupt) interface +* QEMU SiFive E PRCI (Power, Reset, Clock, Interrupt) interface * * Copyright (c) 2017 SiFive, Inc. *
@@ -16,8 +16,8 @@* this program. If not, see <http://www.gnu.org/licenses/>. */ -#ifndef HW_SIFIVE_PRCI_H -#define HW_SIFIVE_PRCI_H +#ifndef HW_SIFIVE_E_PRCI_H +#define HW_SIFIVE_E_PRCI_H enum { SIFIVE_PRCI_HFROSCCFG = 0x0,
@@ -47,10 +47,10 @@ enum {SIFIVE_PRCI_PLLOUTDIV_DIV1 = (1 <<8 ) }; -#define TYPE_SIFIVE_PRCI "riscv.sifive.prci" +#define TYPE_SIFIVE_E_PRCI "riscv.sifive.e.prci" -#define SIFIVE_PRCI (obj) \ - OBJECT_CHECK(SiFivePRCIState, (obj), TYPE_SIFIVE_PRCI) +#define SIFIVE_E_PRCI (obj) \ + OBJECT_CHECK(SiFivePRCIState, (obj), TYPE_SIFIVE_E_PRCI) typedef struct SiFivePRCIState { /*< private >*/
@@ -64,6 +64,6 @@ typedef struct SiFivePRCIState { uint32_t plloutdiv; } SiFivePRCIState; -DeviceState *sifive_prci_create (hwaddr addr); +DeviceState *sifive_e_prci_create (hwaddr addr);#endif
Signature · 1 line
2.7.4
Re: [Qemu-devel] [PATCH v2 11/28] riscv: sifive: Rename sifive_prci.{c, h} to sifive_e_prci.{c, h}
Quoted 51 lines · Bin Meng
Current SiFive PRCI model only works with
sifive_emachine, as it only emulates registers or PRCI block in the FE310 SoC.Rename the file name to make it clear that it is for
sifive_e.Signed-off-by Bin Meng <[email protected]>---
Changes in v2: None
hw/riscv/Makefile.objs | 2 +- hw/riscv/sifive_e.c | 4 ++-- hw/riscv/{sifive_prci.c => sifive_e_prci.c} | 14 +++++++------- include/hw/riscv/{sifive_prci.h => sifive_e_prci.h} | 14 +++++++------- 4 files changed, 17 insertions(+), 17 deletions(-) rename hw/riscv/{sifive_prci.c => sifive_e_prci.c} (90%) rename include/hw/riscv/{sifive_prci.h => sifive_e_prci.h} (82%)hw/riscv/Makefile.objs +1
-1@@ -2,9 +2,9 @@ obj-y += boot.o obj-$(CONFIG_SPIKE) += riscv_htif.o obj-$(CONFIG_HART) += riscv_hart.o obj-$(CONFIG_SIFIVE_E) += sifive_e.o +obj-$(CONFIG_SIFIVE_E) += sifive_e_prci.o obj-$(CONFIG_SIFIVE) += sifive_clint.o obj-$(CONFIG_SIFIVE) += sifive_gpio.o -obj-$(CONFIG_SIFIVE) += sifive_prci.o obj-$(CONFIG_SIFIVE) += sifive_plic.o obj-$(CONFIG_SIFIVE) += sifive_test.o obj-$(CONFIG_SIFIVE_U) += sifive_u.ohw/riscv/sifive_e.c +1
-1@@ -41,9 +41,9 @@#include "hw/riscv/riscv_hart.h" #include "hw/riscv/sifive_plic.h" #include "hw/riscv/sifive_clint.h" -#include "hw/riscv/sifive_prci.h" #include "hw/riscv/sifive_uart.h" #include "hw/riscv/sifive_e.h" +#include "hw/riscv/sifive_e_prci.h" #include "hw/riscv/boot.h" #include "chardev/char.h" #include "sysemu/arch_init.h"
hw/riscv/sifive_e.c static void riscv_sifive_e_soc_realize(DeviceState · line 180
Quoted 8 lines
hw/riscv/sifive_e.c +1
-1@@ -174,7 +174,7 @@ static void riscv_sifive_e_soc_realize(DeviceState *dev, Error **errp) SIFIVE_SIP_BASE, SIFIVE_TIMECMP_BASE, SIFIVE_TIME_BASE);sifive_mmio_emulate (sys_mem,"riscv.sifive.e.aon" , memmap[SIFIVE_E_AON ].base, memmap[SIFIVE_E_AON ].size); -sifive_prci_create (memmap[SIFIVE_E_PRCI ].base); +sifive_e_prci_create (memmap[SIFIVE_E_PRCI ].base);/* GPIO */
I think adding infix to function name is sufficient and keeping the filename the same may be better.
The U board PRCI or variant implementation in future could be included in the same files with different create function
chihmin
Quoted 111 lines
hw/riscv/sifive_e_prci.c renamed from hw/riscv/sifive_prci.c +2
-2@@ -1,5 +1,5 @@/* -* QEMU SiFive PRCI (Power, Reset, Clock, Interrupt) +* QEMU SiFive E PRCI (Power, Reset, Clock, Interrupt) * * Copyright (c) 2017 SiFive, Inc. * @@ -22,7 +22,7 @@#include "hw/sysbus.h" #include "qemu/module.h" #include "target/riscv/cpu.h" -#include "hw/riscv/sifive_prci.h" +#include "hw/riscv/sifive_e_prci.h" static uint64_t sifive_prci_read (void *opaque,hwaddr addr,unsigned int size){
hw/riscv/sifive_e_prci.c renamed from hw/riscv/sifive_prci.c +5
-5@@ -82,10 +82,10 @@ static const MemoryRegionOps sifive_prci_ops = {static void sifive_prci_init (Object *obj) { -SiFivePRCIState *s =SIFIVE_PRCI (obj); +SiFivePRCIState *s =SIFIVE_E_PRCI (obj);memory_region_init_io (&s->mmio, obj, &sifive_prci_ops, s, -TYPE_SIFIVE_PRCI ,0x8000 ); +TYPE_SIFIVE_E_PRCI ,0x8000 );sysbus_init_mmio (SYS_BUS_DEVICE (obj), &s->mmio); s->hfrosccfg = (SIFIVE_PRCI_HFROSCCFG_RDY |SIFIVE_PRCI_HFROSCCFG_EN );@@ -97,7 +97,7 @@ static void sifive_prci_init(Object *obj) }static const TypeInfo sifive_prci_info = { - .name =TYPE_SIFIVE_PRCI , + .name =TYPE_SIFIVE_E_PRCI , .parent =TYPE_SYS_BUS_DEVICE , .instance_size =sizeof (SiFivePRCIState), .instance_init = sifive_prci_init,@@ -114,9 +114,9 @@ type_init(sifive_prci_register_types)/* * Create PRCI device. */ -DeviceState *sifive_prci_create (hwaddr addr) +DeviceState *sifive_e_prci_create (hwaddr addr) { -DeviceState *dev =qdev_create (NULL ,TYPE_SIFIVE_PRCI ); +DeviceState *dev =qdev_create (NULL ,TYPE_SIFIVE_E_PRCI );qdev_init_nofail (dev);sysbus_mmio_map (SYS_BUS_DEVICE (dev),0 , addr);return dev;include/hw/riscv/sifive_e_prci.h renamed from include/hw/riscv/sifive_prci.h +7
-8@@ -1,5 +1,5 @@/* -* QEMU SiFive PRCI (Power, Reset, Clock, Interrupt) interface +* QEMU SiFive E PRCI (Power, Reset, Clock, Interrupt) interface * * Copyright (c) 2017 SiFive, Inc. * @@ -16,8 +16,8 @@* this program. If not, see <http://www.gnu.org/licenses/>. */ -#ifndef HW_SIFIVE_PRCI_H -#define HW_SIFIVE_PRCI_H +#ifndef HW_SIFIVE_E_PRCI_H +#define HW_SIFIVE_E_PRCI_H enum { SIFIVE_PRCI_HFROSCCFG = 0x0,@@ -47,10 +47,10 @@ enum {SIFIVE_PRCI_PLLOUTDIV_DIV1 = (1 <<8 ) }; -#define TYPE_SIFIVE_PRCI "riscv.sifive.prci" +#define TYPE_SIFIVE_E_PRCI "riscv.sifive.e.prci" -#define SIFIVE_PRCI (obj) \ - OBJECT_CHECK(SiFivePRCIState, (obj), TYPE_SIFIVE_PRCI) +#define SIFIVE_E_PRCI (obj) \ + OBJECT_CHECK(SiFivePRCIState, (obj), TYPE_SIFIVE_E_PRCI) typedef struct SiFivePRCIState { /*< private >*/@@ -64,6 +64,6 @@ typedef struct SiFivePRCIState { uint32_t plloutdiv; } SiFivePRCIState; -DeviceState *sifive_prci_create (hwaddr addr); +DeviceState *sifive_e_prci_create (hwaddr addr);#endif --2.7.4
Re: [Qemu-devel] [PATCH v2 11/28] riscv: sifive: Rename sifive_prci.{c, h} to sifive_e_prci.{c, h}
Quoted 60 lines · Chih-Min Chao
Quoted 56 lines · Bin Meng
Current SiFive PRCI model only works with
sifive_emachine, as it only emulates registers or PRCI block in the FE310 SoC.Rename the file name to make it clear that it is for
sifive_e.Signed-off-by Bin Meng <[email protected]>---
Changes in v2: None
hw/riscv/Makefile.objs | 2 +- hw/riscv/sifive_e.c | 4 ++-- hw/riscv/{sifive_prci.c => sifive_e_prci.c} | 14 +++++++------- include/hw/riscv/{sifive_prci.h => sifive_e_prci.h} | 14 +++++++------- 4 files changed, 17 insertions(+), 17 deletions(-) rename hw/riscv/{sifive_prci.c => sifive_e_prci.c} (90%) rename include/hw/riscv/{sifive_prci.h => sifive_e_prci.h} (82%)hw/riscv/Makefile.objs +1
-1@@ -2,9 +2,9 @@ obj-y += boot.o obj-$(CONFIG_SPIKE) += riscv_htif.o obj-$(CONFIG_HART) += riscv_hart.o obj-$(CONFIG_SIFIVE_E) += sifive_e.o +obj-$(CONFIG_SIFIVE_E) += sifive_e_prci.o obj-$(CONFIG_SIFIVE) += sifive_clint.o obj-$(CONFIG_SIFIVE) += sifive_gpio.o -obj-$(CONFIG_SIFIVE) += sifive_prci.o obj-$(CONFIG_SIFIVE) += sifive_plic.o obj-$(CONFIG_SIFIVE) += sifive_test.o obj-$(CONFIG_SIFIVE_U) += sifive_u.ohw/riscv/sifive_e.c +2
-2@@ -41,9 +41,9 @@#include "hw/riscv/riscv_hart.h" #include "hw/riscv/sifive_plic.h" #include "hw/riscv/sifive_clint.h" -#include "hw/riscv/sifive_prci.h" #include "hw/riscv/sifive_uart.h" #include "hw/riscv/sifive_e.h" +#include "hw/riscv/sifive_e_prci.h" #include "hw/riscv/boot.h" #include "chardev/char.h" #include "sysemu/arch_init.h" @@ -174,7 +174,7 @@ static void riscv_sifive_e_soc_realize(DeviceState *dev, Error **errp) SIFIVE_SIP_BASE, SIFIVE_TIMECMP_BASE, SIFIVE_TIME_BASE);sifive_mmio_emulate (sys_mem,"riscv.sifive.e.aon" , memmap[SIFIVE_E_AON ].base, memmap[SIFIVE_E_AON ].size); -sifive_prci_create (memmap[SIFIVE_E_PRCI ].base); +sifive_e_prci_create (memmap[SIFIVE_E_PRCI ].base);
Quoted 6 lines
hw/riscv/sifive_e.c static void riscv_sifive_e_soc_realize(DeviceState *dev, Error **errp) · line 180
Quoted 2 lines
hw/riscv/sifive_e.c +0
-0/* GPIO */ I think adding infix to function name is sufficient and keeping the filename the same may be better. The U board PRCI or variant implementation in future could be included in the same files with different create function
I considered such approach when working on this one, but later I chose to implement a new file for SiFive U machine.
The SiFive U and E PRCI blocks have different register blocks so if we put two variants into one file, their functions don't have much in common and we end up just merely physically put them into one file which does not bring too much benefit IMHO.
Regards,
Bin
Chih-Min Chao
Reviewed-byRe: [Qemu-devel] [PATCH v2 11/28] riscv: sifive: Rename sifive_prci.{c, h} to sifive_e_prci.{c, h}
Quoted 75 lines · Bin Meng
Quoted 46 lines · Chih-Min Chao
Quoted 42 lines · Bin Meng
Current SiFive PRCI model only works with
sifive_emachine, as it only emulates registers or PRCI block in the FE310 SoC.Rename the file name to make it clear that it is for
sifive_e.Signed-off-by Bin Meng <[email protected]>---
Changes in v2: None
hw/riscv/Makefile.objs | 2 +- hw/riscv/sifive_e.c | 4 ++-- hw/riscv/{sifive_prci.c => sifive_e_prci.c} | 14 +++++++------- include/hw/riscv/{sifive_prci.h => sifive_e_prci.h} | 14 +++++++------- 4 files changed, 17 insertions(+), 17 deletions(-) rename hw/riscv/{sifive_prci.c => sifive_e_prci.c} (90%) rename include/hw/riscv/{sifive_prci.h => sifive_e_prci.h} (82%)hw/riscv/Makefile.objs +1
-1@@ -2,9 +2,9 @@ obj-y += boot.o obj-$(CONFIG_SPIKE) += riscv_htif.o obj-$(CONFIG_HART) += riscv_hart.o obj-$(CONFIG_SIFIVE_E) += sifive_e.o +obj-$(CONFIG_SIFIVE_E) += sifive_e_prci.o obj-$(CONFIG_SIFIVE) += sifive_clint.o obj-$(CONFIG_SIFIVE) += sifive_gpio.o -obj-$(CONFIG_SIFIVE) += sifive_prci.o obj-$(CONFIG_SIFIVE) += sifive_plic.o obj-$(CONFIG_SIFIVE) += sifive_test.o obj-$(CONFIG_SIFIVE_U) += sifive_u.ohw/riscv/sifive_e.c +0
-0@@ -41,9 +41,9 @@#include "hw/riscv/riscv_hart.h" #include "hw/riscv/sifive_plic.h" #include "hw/riscv/sifive_clint.h" Quoted 8 lines
hw/riscv/sifive_e.c static void riscv_sifive_e_soc_realize(DeviceState
Quoted 8 lines
hw/riscv/sifive_e.c +1
-1-#include "hw/riscv/sifive_prci.h" #include "hw/riscv/sifive_uart.h" #include "hw/riscv/sifive_e.h" +#include "hw/riscv/sifive_e_prci.h" #include "hw/riscv/boot.h" #include "chardev/char.h" #include "sysemu/arch_init.h" @@ -174,7 +174,7 @@ static void riscv_sifive_e_soc_realize(DeviceState*dev, Error **errp)
Quoted 10 lines
hw/riscv/sifive_e.c static void riscv_sifive_e_soc_realize(DeviceState *dev, Error **errp) · line 180
Quoted 8 lines
hw/riscv/sifive_e.c +1
-1SIFIVE_SIP_BASE, SIFIVE_TIMECMP_BASE, SIFIVE_TIME_BASE);sifive_mmio_emulate (sys_mem,"riscv.sifive.e.aon" , memmap[SIFIVE_E_AON ].base, memmap[SIFIVE_E_AON ].size); -sifive_prci_create (memmap[SIFIVE_E_PRCI ].base); +sifive_e_prci_create (memmap[SIFIVE_E_PRCI ].base);/* GPIO */ I think adding infix to function name is sufficient and keeping the
filename the same may be better.
Quoted 1 line
The U board PRCI or variant implementation in future could be included
in the same files with different create function
Quoted 1 line
I considered such approach when working on this one, but later I chose to implement a new file for SiFive U machine.
Quoted 8 lines
The SiFive U and E PRCI blocks have different register blocks so if we put two variants into one file, their functions don't have much in common and we end up just merely physically put them into one file which does not bring too much benefit IMHO.
Regards,
Bin
agree that the difference between u and e prci are a lot and it make sense to separate it
Re: [Qemu-devel] [PATCH v2 11/28] riscv: sifive: Rename sifive_prci.{c, h} to sifive_e_prci.{c, h}
In reply to Bin MengQuoted 82 lines · Bin Meng
Current SiFive PRCI model only works with
sifive_emachine, as it only emulates registers or PRCI block in the FE310 SoC.Rename the file name to make it clear that it is for
sifive_e.Signed-off-by Bin Meng <[email protected]>---
Changes in v2: None
hw/riscv/Makefile.objs | 2 +- hw/riscv/sifive_e.c | 4 ++-- hw/riscv/{sifive_prci.c => sifive_e_prci.c} | 14 +++++++------- include/hw/riscv/{sifive_prci.h => sifive_e_prci.h} | 14 +++++++------- 4 files changed, 17 insertions(+), 17 deletions(-) rename hw/riscv/{sifive_prci.c => sifive_e_prci.c} (90%) rename include/hw/riscv/{sifive_prci.h => sifive_e_prci.h} (82%)hw/riscv/Makefile.objs +1
-1@@ -2,9 +2,9 @@ obj-y += boot.o obj-$(CONFIG_SPIKE) += riscv_htif.o obj-$(CONFIG_HART) += riscv_hart.o obj-$(CONFIG_SIFIVE_E) += sifive_e.o +obj-$(CONFIG_SIFIVE_E) += sifive_e_prci.o obj-$(CONFIG_SIFIVE) += sifive_clint.o obj-$(CONFIG_SIFIVE) += sifive_gpio.o -obj-$(CONFIG_SIFIVE) += sifive_prci.o obj-$(CONFIG_SIFIVE) += sifive_plic.o obj-$(CONFIG_SIFIVE) += sifive_test.o obj-$(CONFIG_SIFIVE_U) += sifive_u.ohw/riscv/sifive_e.c +2
-2@@ -41,9 +41,9 @@#include "hw/riscv/riscv_hart.h" #include "hw/riscv/sifive_plic.h" #include "hw/riscv/sifive_clint.h" -#include "hw/riscv/sifive_prci.h" #include "hw/riscv/sifive_uart.h" #include "hw/riscv/sifive_e.h" +#include "hw/riscv/sifive_e_prci.h" #include "hw/riscv/boot.h" #include "chardev/char.h" #include "sysemu/arch_init.h" @@ -174,7 +174,7 @@ static void riscv_sifive_e_soc_realize(DeviceState *dev, Error **errp) SIFIVE_SIP_BASE, SIFIVE_TIMECMP_BASE, SIFIVE_TIME_BASE);sifive_mmio_emulate (sys_mem,"riscv.sifive.e.aon" , memmap[SIFIVE_E_AON ].base, memmap[SIFIVE_E_AON ].size); -sifive_prci_create (memmap[SIFIVE_E_PRCI ].base); +sifive_e_prci_create (memmap[SIFIVE_E_PRCI ].base);/* GPIO */ hw/riscv/sifive_e_prci.c renamed from hw/riscv/sifive_prci.c +2
-2@@ -1,5 +1,5 @@/* -* QEMU SiFive PRCI (Power, Reset, Clock, Interrupt) +* QEMU SiFive E PRCI (Power, Reset, Clock, Interrupt) * * Copyright (c) 2017 SiFive, Inc. * @@ -22,7 +22,7 @@#include "hw/sysbus.h" #include "qemu/module.h" #include "target/riscv/cpu.h" -#include "hw/riscv/sifive_prci.h" +#include "hw/riscv/sifive_e_prci.h" static uint64_t sifive_prci_read (void *opaque,hwaddr addr,unsigned int size) {
hw/riscv/sifive_e_prci.c static const MemoryRegionOps sifive_prci_ops = { · line 85
Quoted 5 lines
hw/riscv/sifive_e_prci.c renamed from hw/riscv/sifive_prci.c +1
-1@@ -82,10 +82,10 @@ static const MemoryRegionOps sifive_prci_ops = {static void sifive_prci_init (Object *obj) { -SiFivePRCIState *s =SIFIVE_PRCI (obj); +SiFivePRCIState *s =SIFIVE_E_PRCI (obj);
Should we not rename the struct as well?
Alistair
Quoted 79 lines
hw/riscv/sifive_e_prci.c renamed from hw/riscv/sifive_prci.c +4
-4memory_region_init_io (&s->mmio, obj, &sifive_prci_ops, s, -TYPE_SIFIVE_PRCI ,0x8000 ); +TYPE_SIFIVE_E_PRCI ,0x8000 );sysbus_init_mmio (SYS_BUS_DEVICE (obj), &s->mmio); s->hfrosccfg = (SIFIVE_PRCI_HFROSCCFG_RDY |SIFIVE_PRCI_HFROSCCFG_EN );@@ -97,7 +97,7 @@ static void sifive_prci_init(Object *obj) }static const TypeInfo sifive_prci_info = { - .name =TYPE_SIFIVE_PRCI , + .name =TYPE_SIFIVE_E_PRCI , .parent =TYPE_SYS_BUS_DEVICE , .instance_size =sizeof (SiFivePRCIState), .instance_init = sifive_prci_init,@@ -114,9 +114,9 @@ type_init(sifive_prci_register_types)/* * Create PRCI device. */ -DeviceState *sifive_prci_create (hwaddr addr) +DeviceState *sifive_e_prci_create (hwaddr addr) { -DeviceState *dev =qdev_create (NULL ,TYPE_SIFIVE_PRCI ); +DeviceState *dev =qdev_create (NULL ,TYPE_SIFIVE_E_PRCI );qdev_init_nofail (dev);sysbus_mmio_map (SYS_BUS_DEVICE (dev),0 , addr);return dev;include/hw/riscv/sifive_e_prci.h renamed from include/hw/riscv/sifive_prci.h +7
-8@@ -1,5 +1,5 @@/* -* QEMU SiFive PRCI (Power, Reset, Clock, Interrupt) interface +* QEMU SiFive E PRCI (Power, Reset, Clock, Interrupt) interface * * Copyright (c) 2017 SiFive, Inc. * @@ -16,8 +16,8 @@* this program. If not, see <http://www.gnu.org/licenses/>. */ -#ifndef HW_SIFIVE_PRCI_H -#define HW_SIFIVE_PRCI_H +#ifndef HW_SIFIVE_E_PRCI_H +#define HW_SIFIVE_E_PRCI_H enum { SIFIVE_PRCI_HFROSCCFG = 0x0,@@ -47,10 +47,10 @@ enum {SIFIVE_PRCI_PLLOUTDIV_DIV1 = (1 <<8 ) }; -#define TYPE_SIFIVE_PRCI "riscv.sifive.prci" +#define TYPE_SIFIVE_E_PRCI "riscv.sifive.e.prci" -#define SIFIVE_PRCI (obj) \ - OBJECT_CHECK(SiFivePRCIState, (obj), TYPE_SIFIVE_PRCI) +#define SIFIVE_E_PRCI (obj) \ + OBJECT_CHECK(SiFivePRCIState, (obj), TYPE_SIFIVE_E_PRCI) typedef struct SiFivePRCIState { /*< private >*/@@ -64,6 +64,6 @@ typedef struct SiFivePRCIState { uint32_t plloutdiv; } SiFivePRCIState; -DeviceState *sifive_prci_create (hwaddr addr); +DeviceState *sifive_e_prci_create (hwaddr addr);#endif --2.7.4
A message that is not in the archive (sent off-list or not yet received): CAEUhbmWENVV+DzX756OCUGYc5ES-aCdD8tpSoVoPspniuiGh2A@mail.gmail.com
Re: [Qemu-devel] [PATCH v2 11/28] riscv: sifive: Rename sifive_prci.{c, h} to sifive_e_prci.{c, h}
Quoted 97 lines · Bin Meng
Hi Alistair,
Quoted 85 lines · Alistair Francis
Quoted 83 lines · Bin Meng
Current SiFive PRCI model only works with
sifive_emachine, as it only emulates registers or PRCI block in the FE310 SoC.Rename the file name to make it clear that it is for
sifive_e.Signed-off-by Bin Meng <[email protected]>---
Changes in v2: None
hw/riscv/Makefile.objs | 2 +- hw/riscv/sifive_e.c | 4 ++-- hw/riscv/{sifive_prci.c => sifive_e_prci.c} | 14 +++++++------- include/hw/riscv/{sifive_prci.h => sifive_e_prci.h} | 14 +++++++------- 4 files changed, 17 insertions(+), 17 deletions(-) rename hw/riscv/{sifive_prci.c => sifive_e_prci.c} (90%) rename include/hw/riscv/{sifive_prci.h => sifive_e_prci.h} (82%)hw/riscv/Makefile.objs +1
-1@@ -2,9 +2,9 @@ obj-y += boot.o obj-$(CONFIG_SPIKE) += riscv_htif.o obj-$(CONFIG_HART) += riscv_hart.o obj-$(CONFIG_SIFIVE_E) += sifive_e.o +obj-$(CONFIG_SIFIVE_E) += sifive_e_prci.o obj-$(CONFIG_SIFIVE) += sifive_clint.o obj-$(CONFIG_SIFIVE) += sifive_gpio.o -obj-$(CONFIG_SIFIVE) += sifive_prci.o obj-$(CONFIG_SIFIVE) += sifive_plic.o obj-$(CONFIG_SIFIVE) += sifive_test.o obj-$(CONFIG_SIFIVE_U) += sifive_u.ohw/riscv/sifive_e.c +2
-2@@ -41,9 +41,9 @@#include "hw/riscv/riscv_hart.h" #include "hw/riscv/sifive_plic.h" #include "hw/riscv/sifive_clint.h" -#include "hw/riscv/sifive_prci.h" #include "hw/riscv/sifive_uart.h" #include "hw/riscv/sifive_e.h" +#include "hw/riscv/sifive_e_prci.h" #include "hw/riscv/boot.h" #include "chardev/char.h" #include "sysemu/arch_init.h" @@ -174,7 +174,7 @@ static void riscv_sifive_e_soc_realize(DeviceState *dev, Error **errp) SIFIVE_SIP_BASE, SIFIVE_TIMECMP_BASE, SIFIVE_TIME_BASE);sifive_mmio_emulate (sys_mem,"riscv.sifive.e.aon" , memmap[SIFIVE_E_AON ].base, memmap[SIFIVE_E_AON ].size); -sifive_prci_create (memmap[SIFIVE_E_PRCI ].base); +sifive_e_prci_create (memmap[SIFIVE_E_PRCI ].base);/* GPIO */ hw/riscv/sifive_e_prci.c renamed from hw/riscv/sifive_prci.c +2
-2@@ -1,5 +1,5 @@/* -* QEMU SiFive PRCI (Power, Reset, Clock, Interrupt) +* QEMU SiFive E PRCI (Power, Reset, Clock, Interrupt) * * Copyright (c) 2017 SiFive, Inc. * @@ -22,7 +22,7 @@#include "hw/sysbus.h" #include "qemu/module.h" #include "target/riscv/cpu.h" -#include "hw/riscv/sifive_prci.h" +#include "hw/riscv/sifive_e_prci.h" static uint64_t sifive_prci_read (void *opaque,hwaddr addr,unsigned int size) {@@ -82,10 +82,10 @@ static const MemoryRegionOps sifive_prci_ops = {Quoted 7 lines
hw/riscv/sifive_e_prci.c static const MemoryRegionOps sifive_prci_ops = { · line 85
Quoted 4 lines
hw/riscv/sifive_e_prci.c renamed from hw/riscv/sifive_prci.c +1
-1static void sifive_prci_init (Object *obj) { -SiFivePRCIState *s =SIFIVE_PRCI (obj); +SiFivePRCIState *s =SIFIVE_E_PRCI (obj);Should we not rename the struct as well?
Quoted 2 lines
I think this is OK given it's only used by
sifive_emachine and will not be mixed withsifive_u.
Structs can be public though, so this seems risky. I feel like it should be renamed with the file.
Alistair
Quoted 3 lines
Regards,
Bin
PATCH v2 12/28 riscv: sifive_e: prci: Fix a typo of hfxosccfg register programming
In reply to Bin MengIt should use SIFIVE_PRCI_HFXOSCCFG_RDY and SIFIVE_PRCI_HFXOSCCFG_EN for hfxosccfg register programming.
---
Changes in v2: None
hw/riscv/sifive_e_prci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
hw/riscv/sifive_e_prci.c +1 -1
@@ -89,7 +89,7 @@ static void sifive_prci_init(Object *obj)sysbus_init_mmio (SYS_BUS_DEVICE (obj), &s->mmio); s->hfrosccfg = (SIFIVE_PRCI_HFROSCCFG_RDY |SIFIVE_PRCI_HFROSCCFG_EN ); - s->hfxosccfg = (SIFIVE_PRCI_HFROSCCFG_RDY |SIFIVE_PRCI_HFROSCCFG_EN ); + s->hfxosccfg = (SIFIVE_PRCI_HFXOSCCFG_RDY |SIFIVE_PRCI_HFXOSCCFG_EN ); s->pllcfg = (SIFIVE_PRCI_PLLCFG_REFSEL |SIFIVE_PRCI_PLLCFG_BYPASS |SIFIVE_PRCI_PLLCFG_LOCK ); s->plloutdiv =SIFIVE_PRCI_PLLOUTDIV_DIV1 ;
Signature · 1 line
2.7.4
Re: [Qemu-devel] [PATCH v2 12/28] riscv: sifive_e: prci: Fix a typo of hfxosccfg register programming
Quoted 26 lines · Bin Meng
It should use
SIFIVE_PRCI_HFXOSCCFG_RDYandSIFIVE_PRCI_HFXOSCCFG_ENfor hfxosccfg register programming.Signed-off-by Bin Meng <[email protected]>Acked-by Alistair Francis <[email protected]>---
Changes in v2: None
hw/riscv/sifive_e_prci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)hw/riscv/sifive_e_prci.c +1
-2@@ -89,7 +89,7 @@ static void sifive_prci_init(Object *obj)sysbus_init_mmio (SYS_BUS_DEVICE (obj), &s->mmio); s->hfrosccfg = (SIFIVE_PRCI_HFROSCCFG_RDY |SIFIVE_PRCI_HFROSCCFG_EN ); - s->hfxosccfg = (SIFIVE_PRCI_HFROSCCFG_RDY |SIFIVE_PRCI_HFROSCCFG_EN ); + s->hfxosccfg = (SIFIVE_PRCI_HFXOSCCFG_RDY |SIFIVE_PRCI_HFXOSCCFG_EN ); s->pllcfg = (SIFIVE_PRCI_PLLCFG_REFSEL |SIFIVE_PRCI_PLLCFG_BYPASS |SIFIVE_PRCI_PLLCFG_LOCK ); s->plloutdiv =SIFIVE_PRCI_PLLOUTDIV_DIV1 ; --
Quoted 3 lines
2.7.4
Re: [Qemu-devel] [PATCH v2 12/28] riscv: sifive_e: prci: Fix a typo of hfxosccfg register programming
In reply to Bin MengQuoted 5 lines · Bin Meng
It should use
SIFIVE_PRCI_HFXOSCCFG_RDYandSIFIVE_PRCI_HFXOSCCFG_ENfor hfxosccfg register programming.Signed-off-by Bin Meng <[email protected]>Acked-by Alistair Francis <[email protected]>
Quoted 21 lines
---
Changes in v2: None
hw/riscv/sifive_e_prci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)hw/riscv/sifive_e_prci.c +1
-1@@ -89,7 +89,7 @@ static void sifive_prci_init(Object *obj)sysbus_init_mmio (SYS_BUS_DEVICE (obj), &s->mmio); s->hfrosccfg = (SIFIVE_PRCI_HFROSCCFG_RDY |SIFIVE_PRCI_HFROSCCFG_EN ); - s->hfxosccfg = (SIFIVE_PRCI_HFROSCCFG_RDY |SIFIVE_PRCI_HFROSCCFG_EN ); + s->hfxosccfg = (SIFIVE_PRCI_HFXOSCCFG_RDY |SIFIVE_PRCI_HFXOSCCFG_EN ); s->pllcfg = (SIFIVE_PRCI_PLLCFG_REFSEL |SIFIVE_PRCI_PLLCFG_BYPASS |SIFIVE_PRCI_PLLCFG_LOCK ); s->plloutdiv =SIFIVE_PRCI_PLLOUTDIV_DIV1 ;
PATCH v2 13/28 riscv: sifive_e: prci: Update the PRCI register block size
In reply to Bin MengCurrently the PRCI register block size is set to 0x8000, but in fact 0x1000 is enough, which is also what the manual says.
---
Changes in v2: None
hw/riscv/sifive_e_prci.c | 2 +- include/hw/riscv/sifive_e_prci.h | 2 ++ 2 files changed, 3 insertions(+), 1 deletion(-)
hw/riscv/sifive_e_prci.c +1 -1
@@ -85,7 +85,7 @@ static void sifive_prci_init(Object *obj)SiFivePRCIState *s =SIFIVE_E_PRCI (obj);memory_region_init_io (&s->mmio, obj, &sifive_prci_ops, s, -TYPE_SIFIVE_E_PRCI ,0x8000 ); +TYPE_SIFIVE_E_PRCI ,SIFIVE_E_PRCI_REG_SIZE );sysbus_init_mmio (SYS_BUS_DEVICE (obj), &s->mmio); s->hfrosccfg = (SIFIVE_PRCI_HFROSCCFG_RDY |SIFIVE_PRCI_HFROSCCFG_EN );
include/hw/riscv/sifive_e_prci.h +2 -0
@@ -47,6 +47,8 @@ enum { SIFIVE_PRCI_PLLOUTDIV_DIV1 = (1 << 8) }; +#define SIFIVE_E_PRCI_REG_SIZE 0x1000 +#define TYPE_SIFIVE_E_PRCI "riscv.sifive.e.prci"#define SIFIVE_E_PRCI (obj) \
Signature · 1 line
2.7.4
Re: [Qemu-devel] [PATCH v2 13/28] riscv: sifive_e: prci: Update the PRCI register block size
Quoted 44 lines · Bin Meng
Currently the PRCI register block size is set to
0x8000, but in fact0x1000is enough, which is also what the manual says.Signed-off-by Bin Meng <[email protected]>---
Changes in v2: None
hw/riscv/sifive_e_prci.c | 2 +- include/hw/riscv/sifive_e_prci.h | 2 ++ 2 files changed, 3 insertions(+), 1 deletion(-)hw/riscv/sifive_e_prci.c +1
-1@@ -85,7 +85,7 @@ static void sifive_prci_init(Object *obj)SiFivePRCIState *s =SIFIVE_E_PRCI (obj);memory_region_init_io (&s->mmio, obj, &sifive_prci_ops, s, -TYPE_SIFIVE_E_PRCI ,0x8000 ); +TYPE_SIFIVE_E_PRCI ,SIFIVE_E_PRCI_REG_SIZE );sysbus_init_mmio (SYS_BUS_DEVICE (obj), &s->mmio); s->hfrosccfg = (SIFIVE_PRCI_HFROSCCFG_RDY |SIFIVE_PRCI_HFROSCCFG_EN );include/hw/riscv/sifive_e_prci.h +2
-1@@ -47,6 +47,8 @@ enum { SIFIVE_PRCI_PLLOUTDIV_DIV1 = (1 << 8) }; +#define SIFIVE_E_PRCI_REG_SIZE 0x1000 +#define TYPE_SIFIVE_E_PRCI "riscv.sifive.e.prci"#define SIFIVE_E_PRCI (obj) \ --2.7.4
Reviewed-by Chih-Min Chao <[email protected]>
PATCH v2 14/28 riscv: sifive: Implement PRCI model for FU540
In reply to Bin MengThis adds a simple PRCI model for FU540 (sifive_u). It has different register layout from the existing PRCI model for FE310 (sifive_e).
---
Changes in v2: None
hw/riscv/Makefile.objs | 1 + hw/riscv/sifive_u_prci.c | 163 +++++++++++++++++++++++++++++++++++++++ include/hw/riscv/sifive_u_prci.h | 90 +++++++++++++++++++++ 3 files changed, 254 insertions(+) create mode 100644 hw/riscv/sifive_u_prci.c create mode 100644 include/hw/riscv/sifive_u_prci.h
hw/riscv/Makefile.objs +1 -0
@@ -8,6 +8,7 @@ obj-$(CONFIG_SIFIVE) += sifive_gpio.o obj-$(CONFIG_SIFIVE) += sifive_plic.o obj-$(CONFIG_SIFIVE) += sifive_test.o obj-$(CONFIG_SIFIVE_U) += sifive_u.o +obj-$(CONFIG_SIFIVE_U) += sifive_u_prci.o obj-$(CONFIG_SIFIVE) += sifive_uart.o obj-$(CONFIG_SPIKE) += spike.o obj-$(CONFIG_RISCV_VIRT) += virt.o
hw/riscv/sifive_u_prci.c new file +163 -0
163 lines not on this page · raw message
include/hw/riscv/sifive_u_prci.h new file +90 -0
90 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v2 15/28 riscv: sifive_u: Generate hfclk and rtcclk nodes
In reply to Bin MengTo keep in sync with Linux kernel device tree, generate hfclk and rtcclk nodes in the device tree, to be referenced by PRCI node.
---
Changes in v2: None
hw/riscv/sifive_u.c | 23 +++++++++++++++++++++++ include/hw/riscv/sifive_u.h | 2 ++ 2 files changed, 25 insertions(+)
hw/riscv/sifive_u.c +23 -0
@@ -77,6 +77,7 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,char *nodename;char ethclk_names[] ="pclk\0hclk\0tx_clk" ;uint32_t plic_phandle, ethclk_phandle, phandle =1 ; +uint32_t hfclk_phandle, rtcclk_phandle; fdt = s->fdt =create_device_tree (&s->fdt_size);if (!fdt) {
@@ -95,6 +96,28 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,qemu_fdt_setprop_cell (fdt,"/soc" ,"#size-cells" ,0x2 );qemu_fdt_setprop_cell (fdt,"/soc" ,"#address-cells" ,0x2 ); + hfclk_phandle = phandle++; + nodename =g_strdup_printf ("/hfclk" ); +qemu_fdt_add_subnode (fdt, nodename); +qemu_fdt_setprop_cell (fdt, nodename,"phandle" , hfclk_phandle); +qemu_fdt_setprop_string (fdt, nodename,"clock-output-names" ,"hfclk" ); +qemu_fdt_setprop_cell (fdt, nodename,"clock-frequency" , +SIFIVE_U_HFCLK_FREQ ); +qemu_fdt_setprop_string (fdt, nodename,"compatible" ,"fixed-clock" ); +qemu_fdt_setprop_cell (fdt, nodename,"#clock-cells" ,0x0 ); +g_free (nodename); + + rtcclk_phandle = phandle++; + nodename =g_strdup_printf ("/rtcclk" ); +qemu_fdt_add_subnode (fdt, nodename); +qemu_fdt_setprop_cell (fdt, nodename,"phandle" , rtcclk_phandle); +qemu_fdt_setprop_string (fdt, nodename,"clock-output-names" ,"rtcclk" ); +qemu_fdt_setprop_cell (fdt, nodename,"clock-frequency" , +SIFIVE_U_RTCCLK_FREQ ); +qemu_fdt_setprop_string (fdt, nodename,"compatible" ,"fixed-clock" ); +qemu_fdt_setprop_cell (fdt, nodename,"#clock-cells" ,0x0 ); +g_free (nodename); + nodename =g_strdup_printf ("/memory@%lx" , (long )memmap[SIFIVE_U_DRAM ].base);qemu_fdt_add_subnode (fdt, nodename);
include/hw/riscv/sifive_u.h +2 -0
@@ -65,6 +65,8 @@ enum {enum {SIFIVE_U_CLOCK_FREQ =1000000000 , +SIFIVE_U_HFCLK_FREQ =33333333 , +SIFIVE_U_RTCCLK_FREQ =1000000 ,SIFIVE_U_GEM_CLOCK_FREQ =125000000 };
Signature · 1 line
2.7.4
PATCH v2 16/28 riscv: sifive_u: Add PRCI block to the SoC
In reply to Bin MengAdd PRCI mmio base address and size mappings to sifive_u machine, and generate the corresponding device tree node.
---
Changes in v2: None
hw/riscv/sifive_u.c | 21 ++++++++++++++++++++- include/hw/riscv/sifive_u.h | 1 + 2 files changed, 21 insertions(+), 1 deletion(-)
hw/riscv/sifive_u.c +20 -1
@@ -9,6 +9,7 @@* 0) UART * 1) CLINT (Core Level Interruptor) * 2) PLIC (Platform Level Interrupt Controller) +* 3) PRCI (Power, Reset, Clock, Interrupt) * * This board currently generates devicetree dynamically that indicates at least * two harts and up to five harts.
@@ -42,6 +43,7 @@#include "hw/riscv/sifive_clint.h" #include "hw/riscv/sifive_uart.h" #include "hw/riscv/sifive_u.h" +#include "hw/riscv/sifive_u_prci.h" #include "hw/riscv/boot.h" #include "chardev/char.h" #include "sysemu/arch_init.h"
@@ -60,6 +62,7 @@ static const struct MemmapEntry { [SIFIVE_U_MROM] = { 0x1000, 0x11000 }, [SIFIVE_U_CLINT] = { 0x2000000, 0x10000 }, [SIFIVE_U_PLIC] = { 0xc000000, 0x4000000 }, + [SIFIVE_U_PRCI] = { 0x10000000, 0x1000 }, [SIFIVE_U_UART0] = { 0x10010000, 0x1000 }, [SIFIVE_U_UART1] = { 0x10011000, 0x1000 }, [SIFIVE_U_DRAM] = { 0x80000000, 0x0 },
@@ -76,7 +79,7 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,uint32_t *cells;char *nodename;char ethclk_names[] ="pclk\0hclk\0tx_clk" ; -uint32_t plic_phandle, ethclk_phandle, phandle =1 ; +uint32_t plic_phandle, prci_phandle, ethclk_phandle, phandle =1 ;uint32_t hfclk_phandle, rtcclk_phandle; fdt = s->fdt =create_device_tree (&s->fdt_size);
@@ -183,6 +186,21 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,g_free (cells);g_free (nodename); + prci_phandle = phandle++; + nodename =g_strdup_printf ("/soc/clock-controller@%lx" , + (long )memmap[SIFIVE_U_PRCI ].base); +qemu_fdt_add_subnode (fdt, nodename); +qemu_fdt_setprop_cell (fdt, nodename,"phandle" , prci_phandle); +qemu_fdt_setprop_cell (fdt, nodename,"#clock-cells" ,0x1 ); +qemu_fdt_setprop_cells (fdt, nodename,"clocks" , + hfclk_phandle, rtcclk_phandle); +qemu_fdt_setprop_cells (fdt, nodename,"reg" , +0x0 , memmap[SIFIVE_U_PRCI ].base, +0x0 , memmap[SIFIVE_U_PRCI ].size); +qemu_fdt_setprop_string (fdt, nodename,"compatible" , +"sifive,fu540-c000-prci" ); +g_free (nodename); + plic_phandle = phandle++; cells =g_new0 (uint32_t, s->soc.cpus.num_harts *4 -2 );for (cpu =0 ; cpu < s->soc.cpus.num_harts; cpu++) {
@@ -422,6 +440,7 @@ static void riscv_sifive_u_soc_realize(DeviceState *dev, Error **errp)sifive_clint_create (memmap[SIFIVE_U_CLINT ].base, memmap[SIFIVE_U_CLINT ].size, ms->smp.cpus,SIFIVE_SIP_BASE ,SIFIVE_TIMECMP_BASE ,SIFIVE_TIME_BASE ); +sifive_u_prci_create (memmap[SIFIVE_U_PRCI ].base);for (i =0 ; i <SIFIVE_U_PLIC_NUM_SOURCES ; i++) { plic_gpios[i] =qdev_get_gpio_in (DEVICE (s->plic), i);
include/hw/riscv/sifive_u.h +1 -0
@@ -51,6 +51,7 @@ enum {SIFIVE_U_MROM ,SIFIVE_U_CLINT ,SIFIVE_U_PLIC , +SIFIVE_U_PRCI ,SIFIVE_U_UART0 ,SIFIVE_U_UART1 , SIFIVE_U_DRAM,
Signature · 1 line
2.7.4
PATCH v2 17/28 riscv: sifive_u: Change UART node name in device tree
In reply to Bin MengOpenSBI for fu540 does DT fix up (see fu540_modify_dt()) by updating chosen "stdout-path" to point to "/soc/serial@...", and U-Boot will use this information to locate the serial node and probe its driver. However currently we generate the UART node name as "/soc/uart@...", causing U-Boot fail to find the serial node in DT.
---
Changes in v2: None
hw/riscv/sifive_u.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
hw/riscv/sifive_u.c +1 -1
@@ -274,7 +274,7 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,qemu_fdt_setprop_cell (fdt, nodename,"reg" ,0x0 );g_free (nodename); - nodename =g_strdup_printf ("/soc/uart@%lx" , + nodename =g_strdup_printf ("/soc/serial@%lx" , (long )memmap[SIFIVE_U_UART0 ].base);qemu_fdt_add_subnode (fdt, nodename);qemu_fdt_setprop_string (fdt, nodename,"compatible" ,"sifive,uart0" );
Signature · 1 line
2.7.4
PATCH v2 18/28 riscv: hw: Implement a model for SiFive FU540 OTP
In reply to Bin MengThis implements a simple model for SiFive FU540 OTP (One-Time Programmable) Memory interface, primarily for reading out the stored serial number from the first 1 KiB of the 16 KiB OTP memory reserved by SiFive for internal use.
---
Changes in v2: None
hw/riscv/Makefile.objs | 1 + hw/riscv/sifive_u_otp.c | 194 ++++++++++++++++++++++++++++++++++++++++ include/hw/riscv/sifive_u_otp.h | 90 +++++++++++++++++++ 3 files changed, 285 insertions(+) create mode 100644 hw/riscv/sifive_u_otp.c create mode 100644 include/hw/riscv/sifive_u_otp.h
hw/riscv/Makefile.objs +1 -0
@@ -8,6 +8,7 @@ obj-$(CONFIG_SIFIVE) += sifive_gpio.o obj-$(CONFIG_SIFIVE) += sifive_plic.o obj-$(CONFIG_SIFIVE) += sifive_test.o obj-$(CONFIG_SIFIVE_U) += sifive_u.o +obj-$(CONFIG_SIFIVE_U) += sifive_u_otp.o obj-$(CONFIG_SIFIVE_U) += sifive_u_prci.o obj-$(CONFIG_SIFIVE) += sifive_uart.o obj-$(CONFIG_SPIKE) += spike.o
hw/riscv/sifive_u_otp.c new file +194 -0
194 lines not on this page · raw message
include/hw/riscv/sifive_u_otp.h new file +90 -0
90 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v2 19/28 riscv: sifive_u: Instantiate OTP memory with a serial number
In reply to Bin MengThis adds an OTP memory with a given serial number to the sifive_u machine. With such support, the upstream U-Boot for sifive_fu540 boots out of the box on the sifive_u machine.
---
Changes in v2: None
hw/riscv/sifive_u.c | 5 +++++ include/hw/riscv/sifive_u.h | 1 + 2 files changed, 6 insertions(+)
hw/riscv/sifive_u.c +5 -0
@@ -10,6 +10,7 @@* 1) CLINT (Core Level Interruptor) * 2) PLIC (Platform Level Interrupt Controller) * 3) PRCI (Power, Reset, Clock, Interrupt) +* 4) OTP (One-Time Programmable) memory with stored serial number * * This board currently generates devicetree dynamically that indicates at least * two harts and up to five harts.
@@ -43,6 +44,7 @@#include "hw/riscv/sifive_clint.h" #include "hw/riscv/sifive_uart.h" #include "hw/riscv/sifive_u.h" +#include "hw/riscv/sifive_u_otp.h" #include "hw/riscv/sifive_u_prci.h" #include "hw/riscv/boot.h" #include "chardev/char.h"
@@ -65,10 +67,12 @@ static const struct MemmapEntry { [SIFIVE_U_PRCI] = { 0x10000000, 0x1000 }, [SIFIVE_U_UART0] = { 0x10010000, 0x1000 }, [SIFIVE_U_UART1] = { 0x10011000, 0x1000 }, + [SIFIVE_U_OTP] = { 0x10070000, 0x1000 }, [SIFIVE_U_DRAM] = { 0x80000000, 0x0 }, [SIFIVE_U_GEM] = { 0x100900FC, 0x2000 }, }; +#define SIFIVE_OTP_SERIAL 1#define GEM_REVISION 0x10070109 static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,
@@ -441,6 +445,7 @@ static void riscv_sifive_u_soc_realize(DeviceState *dev, Error **errp) memmap[SIFIVE_U_CLINT ].size, ms->smp.cpus, SIFIVE_SIP_BASE, SIFIVE_TIMECMP_BASE, SIFIVE_TIME_BASE);sifive_u_prci_create (memmap[SIFIVE_U_PRCI ].base); +sifive_u_otp_create (memmap[SIFIVE_U_OTP ].base,SIFIVE_OTP_SERIAL );for (i =0 ; i <SIFIVE_U_PLIC_NUM_SOURCES ; i++) { plic_gpios[i] =qdev_get_gpio_in (DEVICE (s->plic), i);
include/hw/riscv/sifive_u.h +1 -0
@@ -54,6 +54,7 @@ enum {SIFIVE_U_PRCI ,SIFIVE_U_UART0 ,SIFIVE_U_UART1 , +SIFIVE_U_OTP ,SIFIVE_U_DRAM , SIFIVE_U_GEM };
Signature · 1 line
2.7.4
PATCH v2 21/28 riscv: sifive_u: Update UART and ethernet node clock properties
In reply to Bin MengNow that we have added PRCI nodes, update existing UART and ethernet nodes to use PRCI as their clock sources, to keep in sync with the Linux kernel device tree.
With above changes, the previously handcrafted "/soc/ethclk" node is no longer needed. Remove it.
---
Changes in v2: None
hw/riscv/sifive_u.c | 21 +++++---------------- include/hw/riscv/sifive_u.h | 3 +-- include/hw/riscv/sifive_u_prci.h | 10 ++++++++++ 3 files changed, 16 insertions(+), 18 deletions(-)
hw/riscv/sifive_u.c +5 -16
@@ -82,8 +82,8 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,int cpu;uint32_t *cells;char *nodename; -char ethclk_names[] ="pclk\0hclk\0tx_clk" ; -uint32_t plic_phandle, prci_phandle, ethclk_phandle, phandle =1 ; +char ethclk_names[] ="pclk\0hclk" ; +uint32_t plic_phandle, prci_phandle, phandle =1 ;uint32_t hfclk_phandle, rtcclk_phandle; fdt = s->fdt =create_device_tree (&s->fdt_size);
@@ -242,17 +242,6 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,g_free (cells);g_free (nodename); - ethclk_phandle = phandle++; - nodename =g_strdup_printf ("/soc/ethclk" ); -qemu_fdt_add_subnode (fdt, nodename); -qemu_fdt_setprop_string (fdt, nodename,"compatible" ,"fixed-clock" ); -qemu_fdt_setprop_cell (fdt, nodename,"#clock-cells" ,0x0 ); -qemu_fdt_setprop_cell (fdt, nodename,"clock-frequency" , -SIFIVE_U_GEM_CLOCK_FREQ ); -qemu_fdt_setprop_cell (fdt, nodename,"phandle" , ethclk_phandle); - ethclk_phandle =qemu_fdt_get_phandle (fdt, nodename); -g_free (nodename); - nodename =g_strdup_printf ("/soc/ethernet@%lx" , (long )memmap[SIFIVE_U_GEM ].base);qemu_fdt_add_subnode (fdt, nodename);
@@ -265,7 +254,7 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,qemu_fdt_setprop_cell (fdt, nodename,"interrupt-parent" , plic_phandle);qemu_fdt_setprop_cell (fdt, nodename,"interrupts" ,SIFIVE_U_GEM_IRQ );qemu_fdt_setprop_cells (fdt, nodename,"clocks" , - ethclk_phandle, ethclk_phandle, ethclk_phandle); + prci_phandle,PRCI_CLK_GEMGXLPLL , prci_phandle,PRCI_CLK_GEMGXLPLL );qemu_fdt_setprop (fdt, nodename,"clocks-names" , ethclk_names,sizeof (ethclk_names));qemu_fdt_setprop_cell (fdt, nodename,"#address-cells" ,1 );
@@ -285,8 +274,8 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,qemu_fdt_setprop_cells (fdt, nodename,"reg" ,0x0 , memmap[SIFIVE_U_UART0 ].base,0x0 , memmap[SIFIVE_U_UART0 ].size); -qemu_fdt_setprop_cell (fdt, nodename,"clock-frequency" , -SIFIVE_U_CLOCK_FREQ /2 ); +qemu_fdt_setprop_cells (fdt, nodename,"clocks" , + prci_phandle,PRCI_CLK_TLCLK );qemu_fdt_setprop_cell (fdt, nodename,"interrupt-parent" , plic_phandle);qemu_fdt_setprop_cell (fdt, nodename,"interrupts" ,SIFIVE_U_UART0_IRQ );
include/hw/riscv/sifive_u.h +1 -2
@@ -68,8 +68,7 @@ enum {enum {SIFIVE_U_CLOCK_FREQ =1000000000 ,SIFIVE_U_HFCLK_FREQ =33333333 , -SIFIVE_U_RTCCLK_FREQ =1000000 , -SIFIVE_U_GEM_CLOCK_FREQ =125000000 +SIFIVE_U_RTCCLK_FREQ =1000000 };#define SIFIVE_U_PLIC_HART_CONFIG "MS"
include/hw/riscv/sifive_u_prci.h +10 -0
@@ -87,4 +87,14 @@ typedef struct SiFivePRCIState {DeviceState *sifive_u_prci_create (hwaddr addr); +/* +* Clock indexes for use by Device Tree data and the PRCI driver. +* +* These values are from sifive-fu540-prci.h in the Linux kernel. +*/ +#define PRCI_CLK_COREPLL 0 +#define PRCI_CLK_DDRPLL 1 +#define PRCI_CLK_GEMGXLPLL 2 +#define PRCI_CLK_TLCLK 3 +#endif /* HW_SIFIVE_U_PRCI_H */
Signature · 1 line
2.7.4
PATCH v2 22/28 riscv: sifive_u: Generate an aliases node in the device tree
In reply to Bin MengThe Linux kernel SiFive UART driver expects an aliases node to be present in the device tree, from which the driver extracts the port number from "serial#" in the aliases node.
---
Changes in v2: None
hw/riscv/sifive_u.c | 2 ++ 1 file changed, 2 insertions(+)
hw/riscv/sifive_u.c +2 -0
@@ -284,6 +284,8 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,if (cmdline) {qemu_fdt_setprop_string (fdt,"/chosen" ,"bootargs" , cmdline); } +qemu_fdt_add_subnode (fdt,"/aliases" ); +qemu_fdt_setprop_string (fdt,"/aliases" ,"serial0" , nodename);g_free (nodename); }
Signature · 1 line
2.7.4
PATCH v2 23/28 riscv: sifive_u: Fix broken GEM support
In reply to Bin MengAt present the GEM support in sifive_u machine is seriously broken.
- The GEM block register base was set to a weird number (0x100900FC), which for no way could work with the cadence_gem model in QEMU.
- The generated DT node for GEM has a "clocks-names" which is an invalid property name.
Not like other GEM variants, the FU540-specific GEM has a management block to control 10/100/1000Mbps link speed changes, that is mapped to 0x100a0000. We can simply map it into MMIO space without special handling using create_unimplemented_device().
Update the GEM node compatible string to use the official name used by the upstream Linux kernel, and add the management block reg base & size to the <reg> property encoding.
Tested with upstream U-Boot and Linux kernel MACB drivers.
---
Changes in v2:
- use create_unimplemented_device() to create the GEM management block instead of sifive_mmio_emulate()
- add "phy-handle" property to the ethernet node
hw/riscv/sifive_u.c | 23 ++++++++++++++++++----- include/hw/riscv/sifive_u.h | 3 ++- 2 files changed, 20 insertions(+), 6 deletions(-)
hw/riscv/sifive_u.c +18 -5
@@ -3,6 +3,7 @@* * Copyright (c) 2016-2017 Sagar Karandikar, [email protected] * Copyright (c) 2017 SiFive, Inc. +* Copyright (c) 2019 Bin Meng <[email protected]> * * Provides a board compatible with the SiFive Freedom U SDK: *
@@ -11,6 +12,7 @@* 2) PLIC (Platform Level Interrupt Controller) * 3) PRCI (Power, Reset, Clock, Interrupt) * 4) OTP (One-Time Programmable) memory with stored serial number +* 5) GEM (Gigabit Ethernet Controller) and management block * * This board currently generates devicetree dynamically that indicates at least * two harts and up to five harts.
@@ -38,6 +40,7 @@#include "hw/loader.h" #include "hw/sysbus.h" #include "hw/char/serial.h" +#include "hw/misc/unimp.h" #include "target/riscv/cpu.h" #include "hw/riscv/riscv_hart.h" #include "hw/riscv/sifive_plic.h"
@@ -69,7 +72,8 @@ static const struct MemmapEntry { [SIFIVE_U_UART1] = { 0x10011000, 0x1000 }, [SIFIVE_U_OTP] = { 0x10070000, 0x1000 }, [SIFIVE_U_DRAM] = { 0x80000000, 0x0 }, - [SIFIVE_U_GEM] = { 0x100900FC, 0x2000 }, + [SIFIVE_U_GEM] = { 0x10090000, 0x2000 }, + [SIFIVE_U_GEM_MGMT] = { 0x100a0000, 0x1000 }, };#define SIFIVE_OTP_SERIAL 1
@@ -84,7 +88,7 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,char *nodename;char ethclk_names[] ="pclk\0hclk" ;uint32_t plic_phandle, prci_phandle, phandle =1 ; -uint32_t hfclk_phandle, rtcclk_phandle; +uint32_t hfclk_phandle, rtcclk_phandle, phy_phandle; fdt = s->fdt =create_device_tree (&s->fdt_size);if (!fdt) {
@@ -242,20 +246,25 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,g_free (cells);g_free (nodename); + phy_phandle = phandle++; nodename =g_strdup_printf ("/soc/ethernet@%lx" , (long )memmap[SIFIVE_U_GEM ].base);qemu_fdt_add_subnode (fdt, nodename); -qemu_fdt_setprop_string (fdt, nodename,"compatible" ,"cdns,macb" ); +qemu_fdt_setprop_string (fdt, nodename,"compatible" , +"sifive,fu540-c000-gem" );qemu_fdt_setprop_cells (fdt, nodename,"reg" ,0x0 , memmap[SIFIVE_U_GEM ].base, -0x0 , memmap[SIFIVE_U_GEM ].size); +0x0 , memmap[SIFIVE_U_GEM ].size, +0x0 , memmap[SIFIVE_U_GEM_MGMT ].base, +0x0 , memmap[SIFIVE_U_GEM_MGMT ].size);qemu_fdt_setprop_string (fdt, nodename,"reg-names" ,"control" );qemu_fdt_setprop_string (fdt, nodename,"phy-mode" ,"gmii" ); +qemu_fdt_setprop_cell (fdt, nodename,"phy-handle" , phy_phandle);qemu_fdt_setprop_cell (fdt, nodename,"interrupt-parent" , plic_phandle);qemu_fdt_setprop_cell (fdt, nodename,"interrupts" ,SIFIVE_U_GEM_IRQ );qemu_fdt_setprop_cells (fdt, nodename,"clocks" , prci_phandle,PRCI_CLK_GEMGXLPLL , prci_phandle,PRCI_CLK_GEMGXLPLL ); -qemu_fdt_setprop (fdt, nodename,"clocks-names" , ethclk_names, +qemu_fdt_setprop (fdt, nodename,"clock-names" , ethclk_names,sizeof (ethclk_names));qemu_fdt_setprop_cell (fdt, nodename,"#address-cells" ,1 );qemu_fdt_setprop_cell (fdt, nodename,"#size-cells" ,0 );
@@ -264,6 +273,7 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap, nodename =g_strdup_printf ("/soc/ethernet@%lx/ethernet-phy@0" , (long )memmap[SIFIVE_U_GEM ].base);qemu_fdt_add_subnode (fdt, nodename); +qemu_fdt_setprop_cell (fdt, nodename,"phandle" , phy_phandle);qemu_fdt_setprop_cell (fdt, nodename,"reg" ,0x0 );g_free (nodename);
@@ -456,6 +466,9 @@ static void riscv_sifive_u_soc_realize(DeviceState *dev, Error **errp)sysbus_mmio_map (SYS_BUS_DEVICE (&s->gem),0 , memmap[SIFIVE_U_GEM ].base);sysbus_connect_irq (SYS_BUS_DEVICE (&s->gem),0 , plic_gpios[SIFIVE_U_GEM_IRQ ]); + +create_unimplemented_device ("riscv.sifive.u.gem-mgmt" , + memmap[SIFIVE_U_GEM_MGMT ].base, memmap[SIFIVE_U_GEM_MGMT ].size); }static void riscv_sifive_u_machine_init (MachineClass *mc)
include/hw/riscv/sifive_u.h +2 -1
@@ -56,7 +56,8 @@ enum {SIFIVE_U_UART1 ,SIFIVE_U_OTP ,SIFIVE_U_DRAM , -SIFIVE_U_GEM +SIFIVE_U_GEM , +SIFIVE_U_GEM_MGMT }; enum {
Signature · 1 line
2.7.4
PATCH v2 24/28 riscv: sifive_u: Support loading initramfs
In reply to Bin MengThe loading of initramfs is currently not supported on 'sifive_u'. Add the support to make '-initrd' command line parameter useful.
---
Changes in v2: None
hw/riscv/sifive_u.c | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-)
hw/riscv/sifive_u.c +12 -1
@@ -328,7 +328,18 @@ static void riscv_sifive_u_init(MachineState *machine) memmap[SIFIVE_U_DRAM].base);if (machine->kernel_filename) { -riscv_load_kernel (machine->kernel_filename); +uint64_t kernel_entry =riscv_load_kernel (machine->kernel_filename); + +if (machine->initrd_filename) { +hwaddr start; +hwaddr end =riscv_load_initrd (machine->initrd_filename, + machine->ram_size, kernel_entry, + &start); +qemu_fdt_setprop_cell (s->fdt,"/chosen" , +"linux,initrd-start" , start); +qemu_fdt_setprop_cell (s->fdt,"/chosen" ,"linux,initrd-end" , + end); + } }/* reset vector */
Signature · 1 line
2.7.4
Re: [Qemu-devel] [PATCH v2 24/28] riscv: sifive_u: Support loading initramfs
Quoted 36 lines · Bin Meng
The loading of initramfs is currently not supported on '
sifive_u'. Add the support to make '-initrd' command line parameter useful.Signed-off-by Bin Meng <[email protected]>---
Changes in v2: None
hw/riscv/sifive_u.c | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-)hw/riscv/sifive_u.c +12
-1@@ -328,7 +328,18 @@ static void riscv_sifive_u_init(MachineState *machine) memmap[SIFIVE_U_DRAM].base);if (machine->kernel_filename) { -riscv_load_kernel (machine->kernel_filename); +uint64_t kernel_entry =riscv_load_kernel (machine->kernel_filename); + +if (machine->initrd_filename) { +hwaddr start; +hwaddr end =riscv_load_initrd (machine->initrd_filename, + machine->ram_size, kernel_entry, + &start); +qemu_fdt_setprop_cell (s->fdt,"/chosen" , +"linux,initrd-start" , start); +qemu_fdt_setprop_cell (s->fdt,"/chosen" ,"linux,initrd-end" , + end); + } }
Quoted 6 lines
/* reset vector */--
2.7.4
virt also does the same thing.
PATCH v2 25/28 riscv: hw: Remove not needed PLIC properties in device tree
In reply to Bin MengThis removes "reg-names" and "riscv,max-priority" properties of the PLIC node from device tree.
---
Changes in v2:
- keep the PLIC compatible string unchanged as OpenSBI uses that for DT fix up
hw/riscv/sifive_u.c | 2 -- hw/riscv/virt.c | 2 -- 2 files changed, 4 deletions(-)
hw/riscv/sifive_u.c +0 -2
@@ -238,8 +238,6 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,qemu_fdt_setprop_cells (fdt, nodename,"reg" ,0x0 , memmap[SIFIVE_U_PLIC ].base,0x0 , memmap[SIFIVE_U_PLIC ].size); -qemu_fdt_setprop_string (fdt, nodename,"reg-names" ,"control" ); -qemu_fdt_setprop_cell (fdt, nodename,"riscv,max-priority" ,7 );qemu_fdt_setprop_cell (fdt, nodename,"riscv,ndev" ,0x35 );qemu_fdt_setprop_cell (fdt, nodename,"phandle" , plic_phandle); plic_phandle =qemu_fdt_get_phandle (fdt, nodename);
hw/riscv/virt.c +0 -2
@@ -244,8 +244,6 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,qemu_fdt_setprop_cells (fdt, nodename,"reg" ,0x0 , memmap[VIRT_PLIC ].base,0x0 , memmap[VIRT_PLIC ].size); -qemu_fdt_setprop_string (fdt, nodename,"reg-names" ,"control" ); -qemu_fdt_setprop_cell (fdt, nodename,"riscv,max-priority" ,7 );qemu_fdt_setprop_cell (fdt, nodename,"riscv,ndev" ,VIRTIO_NDEV );qemu_fdt_setprop_cell (fdt, nodename,"phandle" , plic_phandle); plic_phandle =qemu_fdt_get_phandle (fdt, nodename);
Signature · 1 line
2.7.4
PATCH v2 27/28 riscv: virt: Change create_fdt() to return void
In reply to Bin MengThere is no need to return fdt at the end of create_fdt() because it's already saved in s->fdt. Other machines (sifive_u, spike) don't do it neither.
---
Changes in v2: None
hw/riscv/virt.c | 11 ++++------- 1 file changed, 4 insertions(+), 7 deletions(-)
hw/riscv/virt.c +4 -7
@@ -112,7 +112,7 @@ static void create_pcie_irq_map(void *fdt, char *nodename, 0x1800, 0, 0, 0x7); } -static void *create_fdt (RISCVVirtState *s,const struct MemmapEntry *memmap, +static void create_fdt (RISCVVirtState *s,const struct MemmapEntry *memmap,uint64_t mem_size,const char *cmdline) {void *fdt;
@@ -316,8 +316,6 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,qemu_fdt_setprop_string (fdt,"/chosen" ,"bootargs" , cmdline); }g_free (nodename); - -return fdt; }
@@ -373,7 +371,6 @@ static void riscv_virt_board_init(MachineState *machine)size_t plic_hart_config_len;int i;unsigned int smp_cpus = machine->smp.cpus; -void *fdt;/* Initialize SOC */ object_initialize_child(OBJECT(machine), "soc", &s->soc, sizeof(s->soc),
@@ -392,7 +389,7 @@ static void riscv_virt_board_init(MachineState *machine) main_mem);/* create device tree */ - fdt =create_fdt (s, memmap, machine->ram_size, machine->kernel_cmdline); +create_fdt (s, memmap, machine->ram_size, machine->kernel_cmdline);/* boot rom */ memory_region_init_rom(mask_rom, NULL, "riscv_virt_board.mrom",
@@ -411,9 +408,9 @@ static void riscv_virt_board_init(MachineState *machine)hwaddr end =riscv_load_initrd (machine->initrd_filename, machine->ram_size, kernel_entry, &start); -qemu_fdt_setprop_cell (fdt,"/chosen" , +qemu_fdt_setprop_cell (s->fdt,"/chosen" ,"linux,initrd-start" , start); -qemu_fdt_setprop_cell (fdt,"/chosen" ,"linux,initrd-end" , +qemu_fdt_setprop_cell (s->fdt,"/chosen" ,"linux,initrd-end" , end); } }
Signature · 1 line
2.7.4
Re: [Qemu-devel] [Qemu-riscv] [PATCH v2 27/28] riscv: virt: Change create_fdt() to return void
Quoted 73 lines · Bin Meng
There is no need to return fdt at the end of
create_fdt()because it's already saved ins->fdt. Other machines (sifive_u, spike) don't do it neither.Signed-off-by Bin Meng <[email protected]>---
Changes in v2: None
hw/riscv/virt.c | 11 ++++------- 1 file changed, 4 insertions(+), 7 deletions(-)hw/riscv/virt.c +1
-1@@ -112,7 +112,7 @@ static void create_pcie_irq_map(void *fdt, char *nodename, 0x1800, 0, 0, 0x7); } -static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap, +static void create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
uint64_tmem_size, const char *cmdline){ void *fdt;hw/riscv/virt.c +0
-3@@ -316,8 +316,6 @@ static void *create_fdt(RISCVVirtState *s, conststruct MemmapEntry *memmap, qemu_fdt_setprop_string(fdt, "/chosen", "bootargs", cmdline); }g_free (nodename); - -return fdt; }@@ -373,7 +371,6 @@ static void riscv_virt_board_init(MachineState *machine)size_t plic_hart_config_len;int i;unsigned int smp_cpus = machine->smp.cpus; -void *fdt;/* Initialize SOC */ object_initialize_child(OBJECT(machine), "soc", &s->soc,
sizeof(s->soc),hw/riscv/virt.c +1
-1@@ -392,7 +389,7 @@ static void riscv_virt_board_init(MachineState *machine) main_mem);/* create device tree */ - fdt =create_fdt (s, memmap, machine->ram_size, machine->kernel_cmdline); +create_fdt (s, memmap, machine->ram_size, machine->kernel_cmdline);/* boot rom */
memory_region_init_rom(mask_rom, NULL, "riscv_virt_board.mrom",hw/riscv/virt.c +2
-2@@ -411,9 +408,9 @@ static void riscv_virt_board_init(MachineState *machine)hwaddr end =riscv_load_initrd (machine->initrd_filename, machine->ram_size, kernel_entry, &start); -qemu_fdt_setprop_cell (fdt,"/chosen" , +qemu_fdt_setprop_cell (s->fdt,"/chosen" ,"linux,initrd-start" , start); -qemu_fdt_setprop_cell (fdt,"/chosen" ,"linux,initrd-end" , +qemu_fdt_setprop_cell (s->fdt,"/chosen" ,"linux,initrd-end" , end);} }
Quoted 5 lines
--
2.7.4
Re: [Qemu-devel] [PATCH v2 27/28] riscv: virt: Change create_fdt() to return void
In reply to Bin MengQuoted 5 lines · Bin Meng
There is no need to return fdt at the end of
create_fdt()because it's already saved ins->fdt. Other machines (sifive_u, spike) don't do it neither.Signed-off-by Bin Meng <[email protected]>
Quoted 59 lines
---
Changes in v2: None
hw/riscv/virt.c | 11 ++++------- 1 file changed, 4 insertions(+), 7 deletions(-)hw/riscv/virt.c +4
-7@@ -112,7 +112,7 @@ static void create_pcie_irq_map(void *fdt, char *nodename, 0x1800, 0, 0, 0x7); } -static void *create_fdt (RISCVVirtState *s,const struct MemmapEntry *memmap, +static void create_fdt (RISCVVirtState *s,const struct MemmapEntry *memmap,uint64_t mem_size,const char *cmdline) {void *fdt;@@ -316,8 +316,6 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,qemu_fdt_setprop_string (fdt,"/chosen" ,"bootargs" , cmdline); }g_free (nodename); - -return fdt; }@@ -373,7 +371,6 @@ static void riscv_virt_board_init(MachineState *machine)size_t plic_hart_config_len;int i;unsigned int smp_cpus = machine->smp.cpus; -void *fdt;/* Initialize SOC */ object_initialize_child(OBJECT(machine), "soc", &s->soc, sizeof(s->soc),@@ -392,7 +389,7 @@ static void riscv_virt_board_init(MachineState *machine) main_mem);/* create device tree */ - fdt =create_fdt (s, memmap, machine->ram_size, machine->kernel_cmdline); +create_fdt (s, memmap, machine->ram_size, machine->kernel_cmdline);/* boot rom */ memory_region_init_rom(mask_rom, NULL, "riscv_virt_board.mrom",@@ -411,9 +408,9 @@ static void riscv_virt_board_init(MachineState *machine)hwaddr end =riscv_load_initrd (machine->initrd_filename, machine->ram_size, kernel_entry, &start); -qemu_fdt_setprop_cell (fdt,"/chosen" , +qemu_fdt_setprop_cell (s->fdt,"/chosen" ,"linux,initrd-start" , start); -qemu_fdt_setprop_cell (fdt,"/chosen" ,"linux,initrd-end" , +qemu_fdt_setprop_cell (s->fdt,"/chosen" ,"linux,initrd-end" , end); } }
PATCH v2 28/28 riscv: sifive_u: Update model and compatible strings in device tree
In reply to Bin MengThis updates model and compatible strings to use the same strings as used in the Linux kernel device tree (hifive-unleashed-a00.dts).
---
Changes in v2: None
hw/riscv/sifive_u.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
hw/riscv/sifive_u.c +3 -2
@@ -96,8 +96,9 @@ static void create_fdt(SiFiveUState *s, const struct MemmapEntry *memmap,exit (1 ); } -qemu_fdt_setprop_string (fdt,"/" ,"model" ,"ucbbar,spike-bare,qemu" ); -qemu_fdt_setprop_string (fdt,"/" ,"compatible" ,"ucbbar,spike-bare-dev" ); +qemu_fdt_setprop_string (fdt,"/" ,"model" ,"SiFive HiFive Unleashed A00" ); +qemu_fdt_setprop_string (fdt,"/" ,"compatible" , +"sifive,hifive-unleashed-a00" );qemu_fdt_setprop_cell (fdt,"/" ,"#size-cells" ,0x2 );qemu_fdt_setprop_cell (fdt,"/" ,"#address-cells" ,0x2 );
Signature · 1 line
2.7.4