arm: exynos: Fix reboot on Odroid HC1
Subsystems (2)
Krzysztof Kozlowski
maintainerv4 cover arm: exynos: Fix reboot on Odroid HC1
Hi,
Changes since v3
================
1. Add accumulated review and test tags.
2. Patch 6: Add "ramp" keyword to new function (as discussed with Torsten Duwe).
3. Rebased on v2019.04-rc3.
Changes since v2
================
1. Add Lukasz review tags.
2. Patch 7: Return on error, as suggested by Simon.
2. Patch 3: Use IS_ENABLED() to run revision detection only once - either during late display board or misc_init_r.
Changes since v1
================
1. Move fixes to beginning of patchset.
2. Patch 3: Rework the idea - split revision detection to be executed later.
3. Patch 4: New patch.
4. Patch 6: Apply Simon's comments.
5. Patch 6: Do not delay when changing voltage if regulator is disabled.
6. Patch 6: Do not delay when disabling the regulator.
Description
===========
Odroid HC1 does not reboot properly (at least from SD card but I do not expect difference on eMMC), if LDO4/VDD_ADC was turned off by Linux kernel. This condition happens so far always, because Linux kernel did not enable ADC on Odroid HC1, therefore the VDD_ADC regulator was turned off as unused.
The issue is in detection of revision which later is used to load proper DTB.
The revision is obtained by ADC read of a voltage depending on VDD_ADC. Therefore:
1. VDD_ADC has to be turned on (but board detection happens before power is initialized),
2. Turning VDD_ADC should wait with ramp delay,
3. Reading the value from ADC should wait for it to stabilize.
Tested on Odroid XU3-Lite and Odroid HC1.
Comments and testing are welcomed.
Best regards,
Krzysztof
Krzysztof Kozlowski (9):
adc: exynos-adc: Fix wrong bit operation used to stop the ADC
power: regulator: s2mps11: Fix step for LDO27 and LDO35
arm: exynos: Detect revision later, when all resources are ready
arm: exynos: odroid-xu3: Display info late to have proper type
arm: exynos: Wait till ADC stabilizes before checking Odroid HC1
revision
regulator: Add support for ramp delay
power: regulator: s2mps11: Add enable delay
arm: dts: exynos: Add supply for ADC block to Odroid XU3 family
arm: dts: exynos: Add ramp delay property to LDO regulators to Odroid
XU3 family
arch/arm/dts/exynos5422-odroidxu3.dts | 20 +++++++ board/samsung/common/board.c | 24 ++++++++- board/samsung/common/exynos5-dt-types.c | 54 +++++++++++++++++-- board/samsung/odroid/odroid.c | 8 +++ configs/odroid-xu3_defconfig | 2 + .../regulator/regulator.txt | 2 + drivers/adc/exynos-adc.c | 2 +- drivers/power/regulator/regulator-uclass.c | 47 +++++++++++++++- drivers/power/regulator/s2mps11_regulator.c | 15 +++++- include/power/regulator.h | 2 + include/samsung/misc.h | 1 + 11 files changed, 167 insertions(+), 10 deletions(-)
Signature · 1 line
2.17.1
Krzysztof Kozlowski
maintainerPATCH v4 1/9 adc: exynos-adc: Fix wrong bit operation used to stop the ADC
When stopping the ADC_V2_CON1_STC_EN should be cleared.
--- drivers/adc/exynos-adc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/adc/exynos-adc.c +1 -1
@@ -62,7 +62,7 @@ int exynos_adc_stop(struct udevice *dev)/* Stop conversion */ cfg =readl (®s->con1); - cfg |= ~ADC_V2_CON1_STC_EN ; + cfg &= ~ADC_V2_CON1_STC_EN ;writel (cfg, ®s->con1);
Signature · 1 line
2.17.1
Krzysztof Kozlowski
maintainerPATCH v4 2/9 power: regulator: s2mps11: Fix step for LDO27 and LDO35
In reply to Krzysztof KozlowskiLDO27 and LDO35 have 25 mV step, not 50 mV.
--- drivers/power/regulator/s2mps11_regulator.c | 4 ++++ 1 file changed, 4 insertions(+)
drivers/power/regulator/s2mps11_regulator.c +4 -0
@@ -346,6 +346,8 @@ static int s2mps11_ldo_hex2volt(int ldo, int hex)case 11 :case 22 :case 23 : +case 27 : +case 35 : uV = hex *S2MPS11_LDO_STEP +S2MPS11_LDO_UV_MIN ;break ;default :
@@ -366,6 +368,8 @@ static int s2mps11_ldo_volt2hex(int ldo, int uV)case 11 :case 22 :case 23 : +case 27 : +case 35 : hex = (uV -S2MPS11_LDO_UV_MIN ) /S2MPS11_LDO_STEP ;break ;default :
Signature · 1 line
2.17.1
Krzysztof Kozlowski
maintainerPATCH v4 3/9 arm: exynos: Detect revision later, when all resources are ready
In reply to Krzysztof KozlowskiDetection of board revision is done early - before power setup. In case of Odroid XU3/XU4/HC1 family, the detection is done using ADC which is supplied by LDO4/VDD_ADC regulator. This regulator could be turned off (e.g. by kernel before reboot). If ADC is used early, the regulators are not yet available and the detection won't work.
Split the revision detection out of set_board_type() into separate function called later - either when displaying board info (in late mode) or during misc_init_r. The idea is that set_board_type() will be called early so its method of detection are limited to flattened device tree (exynos5-dt-types.c for Exynos5) or GPIO (odroid.c for Exynos4412). The newly added set_board_revision() can be called only later, when resources like regulator are available.
This is necessary to fix the detection of Odroid HC1 after reboot, if kernel turned off the LDO4 regulator.
--- board/samsung/common/board.c | 22 +++++++++++++++++++++- board/samsung/common/exynos5-dt-types.c | 16 +++++++++++++--- board/samsung/odroid/odroid.c | 8 ++++++++ include/samsung/misc.h | 1 + 4 files changed, 43 insertions(+), 4 deletions(-)
board/samsung/common/board.c +21 -1
@@ -253,7 +253,18 @@ int board_eth_init(bd_t *bis)int checkboard (void ) {if (IS_ENABLED (CONFIG_BOARD_TYPES )) { -const char *board_info =get_board_type (); +const char *board_info; + +if (IS_ENABLED (CONFIG_DISPLAY_BOARDINFO_LATE )) { +/* +* Printing type requires having revision, although +* this will succeed only if done late. +* Otherwise revision will be set in misc_init_r(). +*/ +set_board_revision (); + } + + board_info =get_board_type ();if (board_info)printf ("Type: %s\n" , board_info);
@@ -287,6 +298,15 @@ int board_late_init(void)#ifdef CONFIG_MISC_INIT_R int misc_init_r (void ) { +if (!IS_ENABLED (CONFIG_DISPLAY_BOARDINFO_LATE )) { +/* +* If revision was not set by late display boardinfo, +* set it here. At this point regulators should be already +* available. +*/ +set_board_revision (); + } +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG set_board_info ();#endif
board/samsung/common/exynos5-dt-types.c +13 -3
@@ -192,8 +192,11 @@ const char *get_board_type(void)/** * set_board_type() - set board type in gd->board_type. -* As default type set EXYNOS5_BOARD_GENERIC, if detect Odroid, -* then set its proper type. +* As default type set EXYNOS5_BOARD_GENERIC. If Odroid is detected, +* set its proper type based on device tree. +* +* This might be called early when some more specific ways to detect revision +* are not yet available. */ void set_board_type (void ) {
@@ -211,8 +214,15 @@ void set_board_type(void) gd->board_type = of_match->data;break ; } +} -/* If Odroid, then check its revision */ +/** +* set_board_revision() - set detailed board type in gd->board_type. +* Should be called when resources (e.g. regulators) are available +* so ADC can be used to detect the specific revision of a board. +*/ +void set_board_revision (void ) +{if (board_is_odroidxu3 ()) gd->board_type =odroid_get_board_type (); }
board/samsung/odroid/odroid.c +8 -0
@@ -54,6 +54,14 @@ void set_board_type(void) gd->board_type =ODROID_TYPE_U3 ; } +void set_board_revision (void ) +{ +/* +* Revision already set by set_board_type() because it can be +* executed early. +*/ +} +const char *get_board_type (void ) {const char *board_type[] = {"u3" ,"x2" };
include/samsung/misc.h +1 -0
@@ -33,6 +33,7 @@ char *get_dfu_alt_system(char *interface, char *devstr);char *get_dfu_alt_boot (char *interface,char *devstr);#endif void set_board_type (void ); +void set_board_revision (void );const char *get_board_type (void );#endif /* __SAMSUNG_MISC_COMMON_H__ */
Signature · 1 line
2.17.1
Krzysztof Kozlowski
maintainerPATCH v4 4/9 arm: exynos: odroid-xu3: Display info late to have proper type
In reply to Krzysztof KozlowskiPrinting the "Type" of board requires proper detection of revision which can happen only late because regulators are needed.
--- board/samsung/common/board.c | 2 +- configs/odroid-xu3_defconfig | 2 ++ 2 files changed, 3 insertions(+), 1 deletion(-)
board/samsung/common/board.c +1 -1
@@ -249,7 +249,7 @@ int board_eth_init(bd_t *bis)return 0 ; } -#ifdef CONFIG_DISPLAY_BOARDINFO +#if defined(CONFIG_DISPLAY_BOARDINFO ) || defined(CONFIG_DISPLAY_BOARDINFO_LATE )int checkboard (void ) {if (IS_ENABLED (CONFIG_BOARD_TYPES )) {
configs/odroid-xu3_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_FIT=y CONFIG_FIT_BEST_MATCH=y CONFIG_SILENT_CONSOLE=y CONFIG_CONSOLE_MUX=y +# CONFIG_DISPLAY_BOARDINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_MISC_INIT_R=y CONFIG_BOARD_TYPES=y CONFIG_SYS_PROMPT="ODROID-XU3 # "
Signature · 1 line
2.17.1
Krzysztof Kozlowski
maintainerPATCH v4 5/9 arm: exynos: Wait till ADC stabilizes before checking Odroid HC1 revision
In reply to Krzysztof KozlowskiFix detection of Odroid HC1 (Exynos5422) after reboot if kernel disabled the LDO4/VDD_ADC regulator.
The LDO4 supplies both ADC block and the ADC input AIN9. Voltage on AIN9 will rise slowly, so use delay of 5 milliseconds instead of timers-based loop to wait for voltage stabilization.
First reads on Odroid HC1 return 305, 1207, 1297 and finally 1308 (reference value is 1309).
--- board/samsung/common/exynos5-dt-types.c | 38 ++++++++++++++++++++++++- 1 file changed, 37 insertions(+), 1 deletion(-)
board/samsung/common/exynos5-dt-types.c +37 -1
@@ -57,12 +57,48 @@ static unsigned int odroid_get_rev(void)return 0 ; } +/* +* Read ADC at least twice and check the resuls. If regulator providing voltage +* on to measured point was just turned on, first reads might require time +* to stabilize. +*/ +static int odroid_get_adc_val (unsigned int *adcval) +{ +unsigned int adcval_prev =0 ; +int ret, retries =20 ; + + ret =adc_channel_single_shot ("adc" ,CONFIG_ODROID_REV_AIN , + &adcval_prev); +if (ret) +return ret; + +while (retries--) { +mdelay (5 ); + + ret =adc_channel_single_shot ("adc" ,CONFIG_ODROID_REV_AIN , + adcval); +if (ret) +return ret; + +/* +* If difference between ADC reads is less than 3%, +* accept the result +*/ +if ((100 *abs (*adcval - adcval_prev) / adcval_prev) <3 ) +return ret; + + adcval_prev = *adcval; + } + +return ret; +} +static int odroid_get_board_type (void ) {unsigned int adcval;int ret, i; - ret =adc_channel_single_shot ("adc" ,CONFIG_ODROID_REV_AIN , &adcval); + ret =odroid_get_adc_val (&adcval);if (ret) goto rev_default;
Signature · 1 line
2.17.1
Krzysztof Kozlowski
maintainerPATCH v4 6/9 regulator: Add support for ramp delay
In reply to Krzysztof KozlowskiChanging voltage and enabling regulator might require delays so the regulator stabilizes at expected level.
Add support for "regulator-ramp-delay" binding which can introduce required time to both enabling the regulator and to changing the voltage.
--- .../regulator/regulator.txt | 2 + drivers/power/regulator/regulator-uclass.c | 47 ++++++++++++++++++- include/power/regulator.h | 2 + 3 files changed, 49 insertions(+), 2 deletions(-)
doc/device-tree-bindings/regulator/regulator.txt +2 -0
@@ -35,6 +35,7 @@ Optional properties: - regulator-max-microamp: a maximum allowed Current value - regulator-always-on: regulator should never be disabled - regulator-boot-on: enabled by bootloader/firmware +- regulator-ramp-delay: ramp delay for regulator (in uV/us) Note The "regulator-name" constraint is used for setting the device's uclass
@@ -60,4 +61,5 @@ ldo0 { regulator-max-microamp = <100000>; regulator-always-on; regulator-boot-on; + regulator-ramp-delay = <12000>; };
drivers/power/regulator/regulator-uclass.c +45 -2
81 lines not on this page · raw message
include/power/regulator.h +2 -0
@@ -150,6 +150,7 @@ enum regulator_flag {* @always_on* - bool type, true or false * @boot_on* - bool type, true or false * TODO(sjg at chromium.org): Consider putting the above two into @flags +* @ramp_delay - Time to settle down after voltage change (unit: uV/us) * @flags: - flags value (see REGULATOR_FLAG_...) * @name** - fdt regulator name - should be taken from the device tree * ctrl_reg: - Control register offset used to enable/disable regulator
@@ -169,6 +170,7 @@ struct dm_regulator_uclass_platdata {int max_uV;int min_uA;int max_uA; +unsigned int ramp_delay;bool always_on;bool boot_on;const char *name;
Signature · 1 line
2.17.1
Krzysztof Kozlowski
maintainerPATCH v4 7/9 power: regulator: s2mps11: Add enable delay
In reply to Krzysztof KozlowskiAccording to datasheet, the output on LDO regulators will start appearing after 10-15 us.
--- drivers/power/regulator/s2mps11_regulator.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-)
drivers/power/regulator/s2mps11_regulator.c +10 -1
@@ -551,7 +551,16 @@ static int ldo_get_enable(struct udevice *dev)static int ldo_set_enable (struct udevice *dev,bool enable) { -return s2mps11_ldo_enable (dev,PMIC_OP_SET , &enable); +int ret; + + ret =s2mps11_ldo_enable (dev,PMIC_OP_SET , &enable); +if (ret) +return ret; + +/* Wait the "enable delay" for voltage to start to rise */ +udelay (15 ); + +return 0 ; }static int ldo_get_mode (struct udevice *dev)
Signature · 1 line
2.17.1
Krzysztof Kozlowski
maintainerPATCH v4 8/9 arm: dts: exynos: Add supply for ADC block to Odroid XU3 family
In reply to Krzysztof KozlowskiThe ADC block requires VDD supply to be on so provide one.
--- arch/arm/dts/exynos5422-odroidxu3.dts | 1 + 1 file changed, 1 insertion(+)
arch/arm/dts/exynos5422-odroidxu3.dts +1 -0
@@ -32,6 +32,7 @@ adc at 12D10000 { u-boot,dm-pre-reloc; + vdd-supply = <&ldo4_reg>; status = "okay"; };
Signature · 1 line
2.17.1
Krzysztof Kozlowski
maintainerPATCH v4 9/9 arm: dts: exynos: Add ramp delay property to LDO regulators to Odroid XU3 family
In reply to Krzysztof KozlowskiAdd startup time to LDO regulators of S2MPS11 PMIC on Odroid XU3/XU4/HC1 family of boards to be sure the voltage is proper before relying on the regulator.
The datasheet for all the S2MPS1x family is inconsistent here and does not specify unambiguously the value of ramp delay for LDO. It mentions 30 mV/us in one timing diagram but then omits it completely in LDO regulator characteristics table (it is specified for bucks).
However the vendor kernels for Galaxy S5 and Odroid XU3 use values of 12 mV/us or 24 mV/us.
Without the ramp delay value the consumers do not wait for voltage settle after changing it. Although the proper value of ramp delay for LDOs is unknown, it seems safer to use at least some value from reference kernel than to leave it unset.
--- arch/arm/dts/exynos5422-odroidxu3.dts | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)
arch/arm/dts/exynos5422-odroidxu3.dts +19 -0
@@ -45,6 +45,7 @@ regulator-name = "vdd_ldo1"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; + regulator-ramp-delay = <12000>; regulator-always-on; };
@@ -52,18 +53,21 @@ regulator-name = "vddq_mmc0"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; + regulator-ramp-delay = <12000>; }; ldo4_reg: LDO4 { regulator-name = "vdd_adc"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; + regulator-ramp-delay = <12000>; }; ldo5_reg: LDO5 { regulator-name = "vdd_ldo5"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; + regulator-ramp-delay = <12000>; regulator-always-on; };
@@ -71,6 +75,7 @@ regulator-name = "vdd_ldo6"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; + regulator-ramp-delay = <12000>; regulator-always-on; };
@@ -78,6 +83,7 @@ regulator-name = "vdd_ldo7"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; + regulator-ramp-delay = <12000>; regulator-always-on; };
@@ -85,6 +91,7 @@ regulator-name = "vdd_ldo8"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; + regulator-ramp-delay = <12000>; regulator-always-on; };
@@ -92,6 +99,7 @@ regulator-name = "vdd_ldo9"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3000000>; + regulator-ramp-delay = <12000>; regulator-always-on; };
@@ -99,6 +107,7 @@ regulator-name = "vdd_ldo10"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; + regulator-ramp-delay = <12000>; regulator-always-on; };
@@ -106,6 +115,7 @@ regulator-name = "vdd_ldo11"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; + regulator-ramp-delay = <12000>; regulator-always-on; };
@@ -113,6 +123,7 @@ regulator-name = "vdd_ldo12"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; + regulator-ramp-delay = <12000>; regulator-always-on; };
@@ -120,12 +131,14 @@ regulator-name = "vddq_mmc2"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; + regulator-ramp-delay = <12000>; }; ldo15_reg: LDO15 { regulator-name = "vdd_ldo15"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; + regulator-ramp-delay = <12000>; regulator-always-on; };
@@ -133,6 +146,7 @@ regulator-name = "vdd_ldo16"; regulator-min-microvolt = <2200000>; regulator-max-microvolt = <2200000>; + regulator-ramp-delay = <12000>; regulator-always-on; };
@@ -140,6 +154,7 @@ regulator-name = "vdd_ldo17"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; + regulator-ramp-delay = <12000>; regulator-always-on; };
@@ -147,18 +162,21 @@ regulator-name = "vdd_emmc_1V8"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; + regulator-ramp-delay = <12000>; }; ldo19_reg: LDO19 { regulator-name = "vdd_sd"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; + regulator-ramp-delay = <12000>; }; ldo24_reg: LDO24 { regulator-name = "tsp_io"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; + regulator-ramp-delay = <12000>; regulator-always-on; };
@@ -166,6 +184,7 @@ regulator-name = "vdd_ldo26"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3000000>; + regulator-ramp-delay = <12000>; regulator-always-on; };
Signature · 1 line
2.17.1
v4 cover arm: exynos: Fix reboot on Odroid HC1
In reply to Krzysztof KozlowskiDear Krzysztof Kozlowski,
Quoted 65 lines · Krzysztof Kozlowski
Hi,
Changes since v3
================
1. Add accumulated review and test tags.
2. Patch 6: Add "ramp" keyword to new function (as discussed with Torsten Duwe).
3. Rebased on v2019.04-rc3.Changes since v2
================
1. Add Lukasz review tags.
2. Patch 7: Return on error, as suggested by Simon.
2. Patch 3: UseIS_ENABLED()to run revision detection only once - either during late display board ormisc_init_r.Changes since v1
================
1. Move fixes to beginning of patchset.
2. Patch 3: Rework the idea - split revision detection to be executed later.
3. Patch 4: New patch.
4. Patch 6: Apply Simon's comments.
5. Patch 6: Do not delay when changing voltage if regulator is disabled.
6. Patch 6: Do not delay when disabling the regulator.Description
===========
Odroid HC1 does not reboot properly (at least from SD card but I do not expect difference on eMMC), if LDO4/VDD_ADC was turned off by Linux kernel. This condition happens so far always, because Linux kernel did not enable ADC on Odroid HC1, therefore theVDD_ADCregulator was turned off as unused.The issue is in detection of revision which later is used to load proper DTB.
The revision is obtained by ADC read of a voltage depending on
VDD_ADC. Therefore:
1.VDD_ADChas to be turned on (but board detection happens before power is initialized),
2. TurningVDD_ADCshould wait with ramp delay,
3. Reading the value from ADC should wait for it to stabilize.Tested on Odroid XU3-Lite and Odroid HC1.
Comments and testing are welcomed.
Best regards,
KrzysztofKrzysztof Kozlowski (9):
adc: exynos-adc: Fix wrong bit operation used to stop the ADC
power: regulator: s2mps11: Fix step for LDO27 and LDO35
arm: exynos: Detect revision later, when all resources are ready
arm: exynos: odroid-xu3: Display info late to have proper type
arm: exynos: Wait till ADC stabilizes before checking Odroid HC1
revision
regulator: Add support for ramp delay
power: regulator: s2mps11: Add enable delay
arm: dts: exynos: Add supply for ADC block to Odroid XU3 family
arm: dts: exynos: Add ramp delay property to LDO regulators to Odroid
XU3 family
Quoted 13 lines
arch/arm/dts/exynos5422-odroidxu3.dts | 20 +++++++ board/samsung/common/board.c | 24 ++++++++- board/samsung/common/exynos5-dt-types.c | 54 +++++++++++++++++-- board/samsung/odroid/odroid.c | 8 +++ configs/odroid-xu3_defconfig | 2 + .../regulator/regulator.txt | 2 + drivers/adc/exynos-adc.c | 2 +- drivers/power/regulator/regulator-uclass.c | 47 +++++++++++++++- drivers/power/regulator/s2mps11_regulator.c | 15 +++++- include/power/regulator.h | 2 + include/samsung/misc.h | 1 + 11 files changed, 167 insertions(+), 10 deletions(-)
Build was failed after apply your patch on trats, trats2 and s5pc210_universal. Please check.
board/samsung/common/built-in.o: In function `misc_init_r':/home/share/Work/u-boot-samsung/board/samsung/common/board.c:307: undefined reference to `set_board_revision'
Thanks,
Minkyu Kang.
Krzysztof Kozlowski
maintainerv4 cover arm: exynos: Fix reboot on Odroid HC1
Quoted 83 lines · Minkyu Kang
Dear Krzysztof Kozlowski,
Quoted 65 lines · Krzysztof Kozlowski
Hi,
Changes since v3
================
1. Add accumulated review and test tags.
2. Patch 6: Add "ramp" keyword to new function (as discussed with Torsten Duwe).
3. Rebased on v2019.04-rc3.Changes since v2
================
1. Add Lukasz review tags.
2. Patch 7: Return on error, as suggested by Simon.
2. Patch 3: UseIS_ENABLED()to run revision detection only once - either during late display board ormisc_init_r.Changes since v1
================
1. Move fixes to beginning of patchset.
2. Patch 3: Rework the idea - split revision detection to be executed later.
3. Patch 4: New patch.
4. Patch 6: Apply Simon's comments.
5. Patch 6: Do not delay when changing voltage if regulator is disabled.
6. Patch 6: Do not delay when disabling the regulator.Description
===========
Odroid HC1 does not reboot properly (at least from SD card but I do not expect difference on eMMC), if LDO4/VDD_ADC was turned off by Linux kernel. This condition happens so far always, because Linux kernel did not enable ADC on Odroid HC1, therefore theVDD_ADCregulator was turned off as unused.The issue is in detection of revision which later is used to load proper DTB.
The revision is obtained by ADC read of a voltage depending on
VDD_ADC. Therefore:
1.VDD_ADChas to be turned on (but board detection happens before power is initialized),
2. TurningVDD_ADCshould wait with ramp delay,
3. Reading the value from ADC should wait for it to stabilize.Tested on Odroid XU3-Lite and Odroid HC1.
Comments and testing are welcomed.
Best regards,
KrzysztofKrzysztof Kozlowski (9):
adc: exynos-adc: Fix wrong bit operation used to stop the ADC
power: regulator: s2mps11: Fix step for LDO27 and LDO35
arm: exynos: Detect revision later, when all resources are ready
arm: exynos: odroid-xu3: Display info late to have proper type
arm: exynos: Wait till ADC stabilizes before checking Odroid HC1
revision
regulator: Add support for ramp delay
power: regulator: s2mps11: Add enable delay
arm: dts: exynos: Add supply for ADC block to Odroid XU3 family
arm: dts: exynos: Add ramp delay property to LDO regulators to Odroid
XU3 familyQuoted 13 lines
arch/arm/dts/exynos5422-odroidxu3.dts | 20 +++++++ board/samsung/common/board.c | 24 ++++++++- board/samsung/common/exynos5-dt-types.c | 54 +++++++++++++++++-- board/samsung/odroid/odroid.c | 8 +++ configs/odroid-xu3_defconfig | 2 + .../regulator/regulator.txt | 2 + drivers/adc/exynos-adc.c | 2 +- drivers/power/regulator/regulator-uclass.c | 47 +++++++++++++++- drivers/power/regulator/s2mps11_regulator.c | 15 +++++- include/power/regulator.h | 2 + include/samsung/misc.h | 1 + 11 files changed, 167 insertions(+), 10 deletions(-)
Quoted 5 lines
Build was failed after apply your patch on trats, trats2 and
s5pc210_universal. Please check.
board/samsung/common/built-in.o: In function `misc_init_r':/home/share/Work/u-boot-samsung/board/samsung/common/board.c:307: undefined reference to `set_board_revision'
Indeed, I need to update other boards as well.
I'll fix it.
Best regards,
Krzysztof