dt-bindings: display: bridge: Add Chipone ICN6211 bindings
Subsystems (5)
Jagan Teki
maintainerPATCH v4 1/2 dt-bindings: display: bridge: Add Chipone ICN6211 bindings
ICN6211 is MIPI-DSI to RGB Converter bridge from Chipone.
It has a flexible configuration of MIPI DSI signal input and produces RGB565, RGB666, RGB888 output format.
Add dt-bingings for it.
---
Changes for v4:
- fixed Laurent comments
- added regulators
- replace reset with EN
- fixed warnings pointed by Robert
Changes for v3:
- updated to new dt-bindings style
.../display/bridge/chipone,icn6211.yaml | 99 +++++++++++++++++++ MAINTAINERS | 5 + 2 files changed, 104 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/bridge/chipone,icn6211.yaml
Documentation/devicetree/bindings/display/bridge/chipone,icn6211.yaml new file +99 -0
@@ -0,0 +1,99 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/bridge/chipone,icn6211.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Chipone ICN6211 MIPI-DSI to RGB Converter bridge + +maintainers: + - Jagan Teki <[email protected]> + +description: | + ICN6211 is MIPI-DSI to RGB Converter bridge from chipone. + + It has a flexible configuration of MIPI DSI signal input and + produce RGB565, RGB666, RGB888 output format. + +properties: + compatible: + enum: + - chipone,icn6211 + + reg: + maxItems: 1 + description: virtual channel number of a DSI peripheral + + enable-gpios: + description: Bridge EN pin, chip is reset when EN is low. + + vdd1-supply: + description: A 1.8V/2.5V/3.3V supply that power the MIPI RX. + + vdd2-supply: + description: A 1.8V/2.5V/3.3V supply that power the PLL. + + vdd3-supply: + description: A 1.8V/2.5V/3.3V supply that power the RGB output. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: + Video port for MIPI DSI input + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + Video port for MIPI DPI output (panel or connector). + + required: + - port@0 + - port@1 + +required: + - compatible + - reg + - enable-gpios + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + dsi { + #address-cells = <1>; + #size-cells = <0>; + + bridge@0 { + compatible = "chipone,icn6211"; + reg = <0>; + enable-gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* LCD-RST: PL5 */ + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + bridge_in_dsi: endpoint { + remote-endpoint = <&dsi_out_bridge>; + }; + }; + + port@1 { + reg = <1>; + + bridge_out_panel: endpoint { + remote-endpoint = <&panel_out_bridge>; + }; + }; + }; + }; + };
MAINTAINERS +5 -0
@@ -5529,6 +5529,11 @@ S: Maintained F: Documentation/devicetree/bindings/display/panel/boe,himax8279d.yaml F: drivers/gpu/drm/panel/panel-boe-himax8279d.c +DRM DRIVER FOR CHIPONE ICN6211 MIPI-DSI to RGB CONVERTER BRIDGE +M: Jagan Teki <[email protected]> +S: Maintained +F: Documentation/devicetree/bindings/display/bridge/chipone,icn6211.yaml + DRM DRIVER FOR FARADAY TVE200 TV ENCODER M: Linus Walleij <[email protected]> S: Maintained
Signature · 6 lines
2.25.1 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Jagan Teki
maintainerPATCH v4 2/2 drm: bridge: Add Chipone ICN6211 MIPI-DSI to RGB bridge
ICN6211 is MIPI-DSI to RGB Converter bridge from Chipone.
It has a flexible configuration of MIPI DSI signal input and produce RGB565, RGB666, RGB888 output format.
Add bridge driver for it.
---
Changes for v4:
- added regulators
- replace reset with EN
- fixed warnings pointed by Robert
Changes for v3:
- updated the driver to inline with new drm bridge style
MAINTAINERS | 1 + drivers/gpu/drm/bridge/Kconfig | 13 + drivers/gpu/drm/bridge/Makefile | 1 + drivers/gpu/drm/bridge/chipone-icn6211.c | 293 +++++++++++++++++++++++ 4 files changed, 308 insertions(+) create mode 100644 drivers/gpu/drm/bridge/chipone-icn6211.c
MAINTAINERS +1 -0
@@ -5533,6 +5533,7 @@ DRM DRIVER FOR CHIPONE ICN6211 MIPI-DSI to RGB CONVERTER BRIDGE M: Jagan Teki <[email protected]> S: Maintained F: Documentation/devicetree/bindings/display/bridge/chipone,icn6211.yaml +F: drivers/gpu/drm/bridge/chipone-icn6211.c DRM DRIVER FOR FARADAY TVE200 TV ENCODER M: Linus Walleij <[email protected]>
drivers/gpu/drm/bridge/Kconfig +13 -0
@@ -27,6 +27,19 @@ config DRM_CDNS_DSI Support Cadence DPI to DSI bridge. This is an internal bridge and is meant to be directly embedded in a SoC. +config DRM_CHIPONE_ICN6211 + tristate "Chipone ICN6211 MIPI-DSI/RGB Converter bridge" + depends on OF + select DRM_MIPI_DSI + select DRM_PANEL_BRIDGE + help + ICN6211 is MIPI-DSI/RGB Converter bridge from chipone. + + It has a flexible configuration of MIPI DSI signal input + and produce RGB565, RGB666, RGB888 output format. + + If in doubt, say "N". + config DRM_CHRONTEL_CH7033 tristate "Chrontel CH7033 Video Encoder" depends on OF
drivers/gpu/drm/bridge/Makefile +1 -0
@@ -1,5 +1,6 @@ # SPDX-License-Identifier: GPL-2.0 obj-$(CONFIG_DRM_CDNS_DSI) += cdns-dsi.o +obj-$(CONFIG_DRM_CHIPONE_ICN6211) += chipone-icn6211.o obj-$(CONFIG_DRM_CHRONTEL_CH7033) += chrontel-ch7033.o obj-$(CONFIG_DRM_DISPLAY_CONNECTOR) += display-connector.o obj-$(CONFIG_DRM_LONTIUM_LT9611) += lontium-lt9611.o
drivers/gpu/drm/bridge/chipone-icn6211.c new file +293 -0
293 lines not on this page · raw message
Signature · 6 lines
2.25.1 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v4 2/2] drm: bridge: Add Chipone ICN6211 MIPI-DSI to RGB bridge
Hey Jagan,
This patch also looks good to me.
Quoted 371 lines · Jagan Teki
ICN6211 is MIPI-DSI to RGB Converter bridge from Chipone.
It has a flexible configuration of MIPI DSI signal input and produce RGB565, RGB666, RGB888 output format.
Add bridge driver for it.
Signed-off-by Jagan Teki <[email protected]>---
Changes for v4:
- added regulators
- replace reset with EN
- fixed warnings pointed by Robert
Changes for v3:
- updated the driver to inline with new drm bridge styleMAINTAINERS | 1 + drivers/gpu/drm/bridge/Kconfig | 13 + drivers/gpu/drm/bridge/Makefile | 1 + drivers/gpu/drm/bridge/chipone-icn6211.c | 293 +++++++++++++++++++++++ 4 files changed, 308 insertions(+) create mode 100644 drivers/gpu/drm/bridge/chipone-icn6211.cMAINTAINERS +1
-0@@ -5533,6 +5533,7 @@ DRM DRIVER FOR CHIPONE ICN6211 MIPI-DSI to RGB CONVERTER BRIDGE M: Jagan Teki <[email protected]> S: Maintained F: Documentation/devicetree/bindings/display/bridge/chipone,icn6211.yaml +F: drivers/gpu/drm/bridge/chipone-icn6211.c DRM DRIVER FOR FARADAY TVE200 TV ENCODER M: Linus Walleij <[email protected]>drivers/gpu/drm/bridge/Kconfig +13
-0@@ -27,6 +27,19 @@ config DRM_CDNS_DSI Support Cadence DPI to DSI bridge. This is an internal bridge and is meant to be directly embedded in a SoC. +config DRM_CHIPONE_ICN6211 + tristate "Chipone ICN6211 MIPI-DSI/RGB Converter bridge" + depends on OF + select DRM_MIPI_DSI + select DRM_PANEL_BRIDGE + help + ICN6211 is MIPI-DSI/RGB Converter bridge from chipone. + + It has a flexible configuration of MIPI DSI signal input + and produce RGB565, RGB666, RGB888 output format. + + If in doubt, say "N". + config DRM_CHRONTEL_CH7033 tristate "Chrontel CH7033 Video Encoder" depends on OFdrivers/gpu/drm/bridge/Makefile +1
-0@@ -1,5 +1,6 @@ # SPDX-License-Identifier: GPL-2.0 obj-$(CONFIG_DRM_CDNS_DSI) += cdns-dsi.o +obj-$(CONFIG_DRM_CHIPONE_ICN6211) += chipone-icn6211.o obj-$(CONFIG_DRM_CHRONTEL_CH7033) += chrontel-ch7033.o obj-$(CONFIG_DRM_DISPLAY_CONNECTOR) += display-connector.o obj-$(CONFIG_DRM_LONTIUM_LT9611) += lontium-lt9611.odrivers/gpu/drm/bridge/chipone-icn6211.c new file +293
-1@@ -0,0 +1,293 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (C) 2020 Amarula Solutions(India) +* Author: Jagan Teki <[email protected]> +*/ + +#include <drm/drm_of.h> +#include <drm/drm_print.h> +#include <drm/drm_mipi_dsi.h> + +#include <linux/delay.h> +#include <linux/gpio/consumer.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/regulator/consumer.h> + +#include <video/mipi_display.h> + +#define HACTIVE_LI 0x20 +#define VACTIVE_LI 0x21 +#define VACTIVE_HACTIVE_HI 0x22 +#define HFP_LI 0x23 +#define HSYNC_LI 0x24 +#define HBP_LI 0x25 +#define HFP_HSW_HBP_HI 0x26 +#define VFP 0x27 +#define VSYNC 0x28 +#define VBP 0x29 + +struct chipone { +struct device *dev; +struct drm_bridge bridge; +struct drm_bridge *panel_bridge; +struct gpio_desc *enable_gpio; +struct regulator *vdd1; +struct regulator *vdd2; +struct regulator *vdd3; +}; + +static inline struct chipone *bridge_to_chipone (struct drm_bridge *bridge) +{ + return container_of(bridge, struct chipone, bridge); +} + +static struct drm_display_mode *bridge_to_mode (struct drm_bridge *bridge) +{ +return &bridge->encoder->crtc->state->adjusted_mode; +} + +static inline int chipone_dsi_write (struct chipone *icn,const void *seq, +size_t len) +{ +struct mipi_dsi_device *dsi =to_mipi_dsi_device (icn->dev); + +return mipi_dsi_generic_write (dsi, seq, len); +} + +#define ICN6211_DSI(icn, seq...) \ + { \ + const u8 d[] = { seq }; \ + chipone_dsi_write(icn, d, ARRAY_SIZE(d)); \ + } + +static void chipone_enable (struct drm_bridge *bridge) +{ +struct chipone *icn =bridge_to_chipone (bridge); +struct drm_display_mode *mode =bridge_to_mode (bridge); + +ICN6211_DSI (icn,0x7a ,0xc1 ); + +ICN6211_DSI (icn,HACTIVE_LI , mode->hdisplay &0xff ); + +ICN6211_DSI (icn,VACTIVE_LI , mode->vdisplay &0xff ); + +/** +* lsb nibble: 2nd nibble of hdisplay +* msb nibble: 2nd nibble of vdisplay +*/ +ICN6211_DSI (icn,VACTIVE_HACTIVE_HI , + ((mode->hdisplay >>8 ) &0xf ) | + (((mode->vdisplay >>8 ) &0xf ) <<4 )); + +ICN6211_DSI (icn,HFP_LI , mode->hsync_start - mode->hdisplay); + +ICN6211_DSI (icn,HSYNC_LI , mode->hsync_end - mode->hsync_start); + +ICN6211_DSI (icn,HBP_LI , mode->htotal - mode->hsync_end); + +ICN6211_DSI (icn,HFP_HSW_HBP_HI ,0x00 ); + +ICN6211_DSI (icn,VFP , mode->vsync_start - mode->vdisplay); + +ICN6211_DSI (icn,VSYNC , mode->vsync_end - mode->vsync_start); + +ICN6211_DSI (icn,VBP , mode->vtotal - mode->vsync_end); + +/* dsi specific sequence */ +ICN6211_DSI (icn,MIPI_DCS_SET_TEAR_OFF ,0x80 ); +ICN6211_DSI (icn,MIPI_DCS_SET_ADDRESS_MODE ,0x28 ); +ICN6211_DSI (icn,0xb5 ,0xa0 ); +ICN6211_DSI (icn,0x5c ,0xff ); +ICN6211_DSI (icn,MIPI_DCS_SET_COLUMN_ADDRESS ,0x01 ); +ICN6211_DSI (icn,MIPI_DCS_GET_POWER_SAVE ,0x92 ); +ICN6211_DSI (icn,0x6b ,0x71 ); +ICN6211_DSI (icn,0x69 ,0x2b ); +ICN6211_DSI (icn,MIPI_DCS_ENTER_SLEEP_MODE ,0x40 ); +ICN6211_DSI (icn,MIPI_DCS_EXIT_SLEEP_MODE ,0x98 ); + +/* icn6211 specific sequence */ +ICN6211_DSI (icn,0xb6 ,0x20 ); +ICN6211_DSI (icn,0x51 ,0x20 ); +ICN6211_DSI (icn,0x09 ,0x10 ); + +usleep_range (10000 ,11000 ); +} + +static void chipone_pre_enable (struct drm_bridge *bridge) +{ +struct chipone *icn =bridge_to_chipone (bridge); +int ret; + +if (icn->vdd1) { + ret =regulator_enable (icn->vdd1); +if (ret) +DRM_DEV_ERROR (icn->dev, +"failed to enable VDD1 regulator: %d\n" , ret); + } + +if (icn->vdd2) { + ret =regulator_enable (icn->vdd2); +if (ret) +DRM_DEV_ERROR (icn->dev, +"failed to enable VDD2 regulator: %d\n" , ret); + } + +if (icn->vdd3) { + ret =regulator_enable (icn->vdd3); +if (ret) +DRM_DEV_ERROR (icn->dev, +"failed to enable VDD3 regulator: %d\n" , ret); + } + +gpiod_set_value (icn->enable_gpio,1 ); + +usleep_range (10000 ,11000 ); +} + +static void chipone_post_disable (struct drm_bridge *bridge) +{ +struct chipone *icn =bridge_to_chipone (bridge); + +if (icn->vdd1) +regulator_disable (icn->vdd1); + +if (icn->vdd2) +regulator_disable (icn->vdd2); + +if (icn->vdd3) +regulator_disable (icn->vdd3); + +gpiod_set_value (icn->enable_gpio,0 ); +} + +static int chipone_attach (struct drm_bridge *bridge,enum drm_bridge_attach_flags flags) +{ +struct chipone *icn =bridge_to_chipone (bridge); + +return drm_bridge_attach (bridge->encoder, icn->panel_bridge, bridge, flags); +} + +static const struct drm_bridge_funcs chipone_bridge_funcs = { + .attach = chipone_attach, + .post_disable = chipone_post_disable, + .pre_enable = chipone_pre_enable, + .enable = chipone_enable, +}; + +static int chipone_parse_dt (struct chipone *icn) +{ +struct device *dev = icn->dev; +struct drm_panel *panel; +int ret; + + icn->vdd1 =devm_regulator_get_optional (dev,"vdd1" ); +if (IS_ERR (icn->vdd1)) { + ret =PTR_ERR (icn->vdd1); +if (ret == -EPROBE_DEFER ) +return -EPROBE_DEFER ; + icn->vdd1 =NULL ; +DRM_DEV_DEBUG (dev,"failed to get VDD1 regulator: %d\n" , ret); + } + + icn->vdd2 =devm_regulator_get_optional (dev,"vdd2" ); +if (IS_ERR (icn->vdd2)) { + ret =PTR_ERR (icn->vdd2); +if (ret == -EPROBE_DEFER ) +return -EPROBE_DEFER ; + icn->vdd2 =NULL ; +DRM_DEV_DEBUG (dev,"failed to get VDD2 regulator: %d\n" , ret); + } + + icn->vdd3 =devm_regulator_get_optional (dev,"vdd3" ); +if (IS_ERR (icn->vdd3)) { + ret =PTR_ERR (icn->vdd3); +if (ret == -EPROBE_DEFER ) +return -EPROBE_DEFER ; + icn->vdd3 =NULL ; +DRM_DEV_DEBUG (dev,"failed to get VDD3 regulator: %d\n" , ret); + } + + icn->enable_gpio =devm_gpiod_get (dev,"enable" ,GPIOD_OUT_LOW ); +if (IS_ERR (icn->enable_gpio)) { +DRM_DEV_ERROR (dev,"failed to get enable GPIO\n" ); +return PTR_ERR (icn->enable_gpio); + } + + ret =drm_of_find_panel_or_bridge (dev->of_node,1 ,0 , &panel,NULL ); +if (ret) +return ret; + + icn->panel_bridge =devm_drm_panel_bridge_add (dev, panel); +if (IS_ERR (icn->panel_bridge)) +return PTR_ERR (icn->panel_bridge); + +return 0 ; +} + +static int chipone_probe (struct mipi_dsi_device *dsi) +{ +struct device *dev = &dsi->dev; +struct chipone *icn; +int ret; + + icn =devm_kzalloc (dev,sizeof (struct chipone ),GFP_KERNEL ); +if (!icn) +return -ENOMEM ; + +mipi_dsi_set_drvdata (dsi, icn); + icn->dev = dev; + + ret =chipone_parse_dt (icn); +if (ret) +return ret; + + icn->bridge.funcs = &chipone_bridge_funcs; + icn->bridge.type =DRM_MODE_CONNECTOR_DPI ; + icn->bridge.of_node = dev->of_node; + +drm_bridge_add (&icn->bridge); + + dsi->lanes =4 ; + dsi->format =MIPI_DSI_FMT_RGB888 ; + dsi->mode_flags =MIPI_DSI_MODE_VIDEO_SYNC_PULSE ; + + ret =mipi_dsi_attach (dsi); +if (ret <0 ) { +drm_bridge_remove (&icn->bridge); +dev_err (dev,"failed to attach dsi\n" ); + } + +return ret; +} + +static int chipone_remove (struct mipi_dsi_device *dsi) +{ +struct chipone *icn =mipi_dsi_get_drvdata (dsi); + +mipi_dsi_detach (dsi); +drm_bridge_remove (&icn->bridge); + +return 0 ; +} + +static const struct of_device_id chipone_of_match[] = { + { .compatible ="chipone,icn6211" , }, + {/* sentinel */ } +}; +MODULE_DEVICE_TABLE (of, chipone_of_match); + +static struct mipi_dsi_driver chipone_driver = { + .probe = chipone_probe, + .remove = chipone_remove, + .driver = { + .name ="chipone-icn6211" , + .owner =THIS_MODULE , + .of_match_table = chipone_of_match, + }, +}; +module_mipi_dsi_driver (chipone_driver); + +MODULE_AUTHOR ("Jagan Teki <[email protected]>" ); +MODULE_DESCRIPTION ("Chipone ICN6211 MIPI-DSI to RGB Converter Bridge" ); +MODULE_LICENSE ("GPL" ); --
Quoted 2 lines
2.25.1
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Hey Jagan,
This looks good to me, feel free to add my r-b.
Quoted 145 lines · Jagan Teki
ICN6211 is MIPI-DSI to RGB Converter bridge from Chipone.
It has a flexible configuration of MIPI DSI signal input and produces RGB565, RGB666, RGB888 output format.
Add dt-bingings for it.
Signed-off-by Jagan Teki <[email protected]>---
Changes for v4:
- fixed Laurent comments
- added regulators
- replace reset with EN
- fixed warnings pointed by Robert
Changes for v3:
- updated to new dt-bindings style.../display/bridge/chipone,icn6211.yaml | 99 +++++++++++++++++++ MAINTAINERS | 5 + 2 files changed, 104 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/bridge/chipone,icn6211.yamlDocumentation/devicetree/bindings/display/bridge/chipone,icn6211.yaml new file +99
-0@@ -0,0 +1,99 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/bridge/chipone,icn6211.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Chipone ICN6211 MIPI-DSI to RGB Converter bridge + +maintainers: + - Jagan Teki <[email protected]> + +description: | + ICN6211 is MIPI-DSI to RGB Converter bridge from chipone. + + It has a flexible configuration of MIPI DSI signal input and + produce RGB565, RGB666, RGB888 output format. + +properties: + compatible: + enum: + - chipone,icn6211 + + reg: + maxItems: 1 + description: virtual channel number of a DSI peripheral + + enable-gpios: + description: Bridge EN pin, chip is reset when EN is low. + + vdd1-supply: + description: A 1.8V/2.5V/3.3V supply that power the MIPI RX. + + vdd2-supply: + description: A 1.8V/2.5V/3.3V supply that power the PLL. + + vdd3-supply: + description: A 1.8V/2.5V/3.3V supply that power the RGB output. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: + Video port for MIPI DSI input + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + Video port for MIPI DPI output (panel or connector). + + required: + - port@0 + - port@1 + +required: + - compatible + - reg + - enable-gpios + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + dsi { + #address-cells = <1>; + #size-cells = <0>; + + bridge@0 { + compatible = "chipone,icn6211"; + reg = <0>; + enable-gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* LCD-RST: PL5 */ + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + bridge_in_dsi: endpoint { + remote-endpoint = <&dsi_out_bridge>; + }; + }; + + port@1 { + reg = <1>; + + bridge_out_panel: endpoint { + remote-endpoint = <&panel_out_bridge>; + }; + }; + }; + }; + };MAINTAINERS +5
-1@@ -5529,6 +5529,11 @@ S: Maintained F: Documentation/devicetree/bindings/display/panel/boe,himax8279d.yaml F: drivers/gpu/drm/panel/panel-boe-himax8279d.c +DRM DRIVER FOR CHIPONE ICN6211 MIPI-DSI to RGB CONVERTER BRIDGE +M: Jagan Teki <[email protected]> +S: Maintained +F: Documentation/devicetree/bindings/display/bridge/chipone,icn6211.yaml + DRM DRIVER FOR FARADAY TVE200 TV ENCODER M: Linus Walleij <[email protected]> S: Maintained --
Quoted 2 lines
2.25.1
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Quoted 17 lines · Jagan Teki
ICN6211 is MIPI-DSI to RGB Converter bridge from Chipone.
It has a flexible configuration of MIPI DSI signal input and produces RGB565, RGB666, RGB888 output format.
Add dt-bingings for it.
Signed-off-by Jagan Teki <[email protected]>---
Changes for v4:
- fixed Laurent comments
- added regulators
- replace reset with EN
- fixed warnings pointed by Robert
Changes for v3:
- updated to new dt-bindings style
Quoted 5 lines
.../display/bridge/chipone,icn6211.yaml | 99 +++++++++++++++++++ MAINTAINERS | 5 + 2 files changed, 104 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/bridge/chipone,icn6211.yaml
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel