Skip to contentSkip to conversation

dt-bindings: display: bridge: Add Chipone ICN6211 bindings

PATCH Applied Jagan Teki 2 participants 3 messages Mar 22, 2021 – Mar 25, 2021

Subsystems (5)
lore
Share & tools
lore

Jagan Teki

author maintainer
#0 lore raw

PATCH v5 1/2 dt-bindings: display: bridge: Add Chipone ICN6211 bindings

ICN6211 is MIPI-DSI to RGB Converter bridge from Chipone.

It has a flexible configuration of MIPI DSI signal input and produces RGB565, RGB666, RGB888 output format.

Add dt-bingings for it.

---
Changes for v5:
- rebase drm-misc-next
- collect Rob, Robert review tags
Changes for v4:
- fixed Laurent comments
- added regulators
- replace reset with EN
- fixed warnings pointed by Robert
Changes for v3:
- updated to new dt-bindings style

 .../display/bridge/chipone,icn6211.yaml       | 99 +++++++++++++++++++
 MAINTAINERS                                   |  5 +
 2 files changed, 104 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/bridge/chipone,icn6211.yaml
Documentation/devicetree/bindings/display/bridge/chipone,icn6211.yaml new file +99 -0
new file mode 100644
index 000000000000..62c3bd4cb28d
@@ -0,0 +1,99 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/chipone,icn6211.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Chipone ICN6211 MIPI-DSI to RGB Converter bridge
+
+maintainers:
+  - Jagan Teki <[email protected]>
+
+description: |
+  ICN6211 is MIPI-DSI to RGB Converter bridge from chipone.
+
+  It has a flexible configuration of MIPI DSI signal input and
+  produce RGB565, RGB666, RGB888 output format.
+
+properties:
+  compatible:
+    enum:
+      - chipone,icn6211
+
+  reg:
+    maxItems: 1
+    description: virtual channel number of a DSI peripheral
+
+  enable-gpios:
+    description: Bridge EN pin, chip is reset when EN is low.
+
+  vdd1-supply:
+    description: A 1.8V/2.5V/3.3V supply that power the MIPI RX.
+
+  vdd2-supply:
+    description: A 1.8V/2.5V/3.3V supply that power the PLL.
+
+  vdd3-supply:
+    description: A 1.8V/2.5V/3.3V supply that power the RGB output.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for MIPI DSI input
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for MIPI DPI output (panel or connector).
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - enable-gpios
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    dsi {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      bridge@0 {
+        compatible = "chipone,icn6211";
+        reg = <0>;
+        enable-gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* LCD-RST: PL5 */
+
+        ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          port@0 {
+            reg = <0>;
+
+            bridge_in_dsi: endpoint {
+              remote-endpoint = <&dsi_out_bridge>;
+            };
+          };
+
+          port@1 {
+            reg = <1>;
+
+            bridge_out_panel: endpoint {
+              remote-endpoint = <&panel_out_bridge>;
+            };
+          };
+        };
+      };
+    };
MAINTAINERS +5 -0
index 4b705ba51c54..b9d11101d060 100644
@@ -5568,6 +5568,11 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/display/panel/boe,himax8279d.yaml
 F:	drivers/gpu/drm/panel/panel-boe-himax8279d.c
 
+DRM DRIVER FOR CHIPONE ICN6211 MIPI-DSI to RGB CONVERTER BRIDGE
+M:	Jagan Teki <[email protected]>
+S:	Maintained
+F:	Documentation/devicetree/bindings/display/bridge/chipone,icn6211.yaml
+
 DRM DRIVER FOR FARADAY TVE200 TV ENCODER
 M:	Linus Walleij <[email protected]>
 S:	Maintained
Signature · 6 lines
2.25.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#1 lore raw

PATCH v5 2/2 drm: bridge: Add Chipone ICN6211 MIPI-DSI to RGB bridge

ICN6211 is MIPI-DSI to RGB Converter bridge from Chipone.

It has a flexible configuration of MIPI DSI signal input and produce RGB565, RGB666, RGB888 output format.

Add bridge driver for it.

---
Changes for v5:
- rebase drm-misc-next
- collect Robert review tags
Changes for v4:
- added regulators
- replace reset with EN
- fixed warnings pointed by Robert
Changes for v3:
- updated the driver to inline with new drm bridge style

 MAINTAINERS                              |   1 +
 drivers/gpu/drm/bridge/Kconfig           |  13 +
 drivers/gpu/drm/bridge/Makefile          |   1 +
 drivers/gpu/drm/bridge/chipone-icn6211.c | 293 +++++++++++++++++++++++
 4 files changed, 308 insertions(+)
 create mode 100644 drivers/gpu/drm/bridge/chipone-icn6211.c
MAINTAINERS +1 -0
index b9d11101d060..b92a35c80eae 100644
@@ -5572,6 +5572,7 @@ DRM DRIVER FOR CHIPONE ICN6211 MIPI-DSI to RGB CONVERTER BRIDGE
 M:	Jagan Teki <[email protected]>
 S:	Maintained
 F:	Documentation/devicetree/bindings/display/bridge/chipone,icn6211.yaml
+F:	drivers/gpu/drm/bridge/chipone-icn6211.c
 
 DRM DRIVER FOR FARADAY TVE200 TV ENCODER
 M:	Linus Walleij <[email protected]>
drivers/gpu/drm/bridge/Kconfig +13 -0
index e4110d6ca7b3..330ee70ed746 100644
@@ -27,6 +27,19 @@ config DRM_CDNS_DSI
 	  Support Cadence DPI to DSI bridge. This is an internal
 	  bridge and is meant to be directly embedded in a SoC.
 
+config DRM_CHIPONE_ICN6211
+	tristate "Chipone ICN6211 MIPI-DSI/RGB Converter bridge"
+	depends on OF
+	select DRM_MIPI_DSI
+	select DRM_PANEL_BRIDGE
+	help
+	  ICN6211 is MIPI-DSI/RGB Converter bridge from chipone.
+
+	  It has a flexible configuration of MIPI DSI signal input
+	  and produce RGB565, RGB666, RGB888 output format.
+
+	  If in doubt, say "N".
+
 config DRM_CHRONTEL_CH7033
 	tristate "Chrontel CH7033 Video Encoder"
 	depends on OF
drivers/gpu/drm/bridge/Makefile +1 -0
index 86e7acc76f8d..3eb84b638988 100644
@@ -1,5 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0
 obj-$(CONFIG_DRM_CDNS_DSI) += cdns-dsi.o
+obj-$(CONFIG_DRM_CHIPONE_ICN6211) += chipone-icn6211.o
 obj-$(CONFIG_DRM_CHRONTEL_CH7033) += chrontel-ch7033.o
 obj-$(CONFIG_DRM_DISPLAY_CONNECTOR) += display-connector.o
 obj-$(CONFIG_DRM_LONTIUM_LT9611) += lontium-lt9611.o
drivers/gpu/drm/bridge/chipone-icn6211.c new file +293 -0

293 lines not on this page · raw message

Signature · 6 lines
2.25.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Applied
#2 lore raw
In reply to Jagan Teki

Pushed to drm-misc-next

https://cgit.freedesktop.org/drm/drm-misc/commit/?id=a42e37db23b88120aea9fa31f9c0952accb39296

Quoted 150 lines · Jagan Teki

ICN6211 is MIPI-DSI to RGB Converter bridge from Chipone.

It has a flexible configuration of MIPI DSI signal input and produces RGB565, RGB666, RGB888 output format.

Add dt-bingings for it.

---
Changes for v5:
- rebase drm-misc-next
- collect Rob, Robert review tags
Changes for v4:
- fixed Laurent comments
- added regulators
- replace reset with EN
- fixed warnings pointed by Robert
Changes for v3:
- updated to new dt-bindings style

 .../display/bridge/chipone,icn6211.yaml       | 99 +++++++++++++++++++
 MAINTAINERS                                   |  5 +
 2 files changed, 104 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/bridge/chipone,icn6211.yaml
Documentation/devicetree/bindings/display/bridge/chipone,icn6211.yaml new file +99 -0
new file mode 100644
index 000000000000..62c3bd4cb28d
@@ -0,0 +1,99 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/chipone,icn6211.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Chipone ICN6211 MIPI-DSI to RGB Converter bridge
+
+maintainers:
+  - Jagan Teki <[email protected]>
+
+description: |
+  ICN6211 is MIPI-DSI to RGB Converter bridge from chipone.
+
+  It has a flexible configuration of MIPI DSI signal input and
+  produce RGB565, RGB666, RGB888 output format.
+
+properties:
+  compatible:
+    enum:
+      - chipone,icn6211
+
+  reg:
+    maxItems: 1
+    description: virtual channel number of a DSI peripheral
+
+  enable-gpios:
+    description: Bridge EN pin, chip is reset when EN is low.
+
+  vdd1-supply:
+    description: A 1.8V/2.5V/3.3V supply that power the MIPI RX.
+
+  vdd2-supply:
+    description: A 1.8V/2.5V/3.3V supply that power the PLL.
+
+  vdd3-supply:
+    description: A 1.8V/2.5V/3.3V supply that power the RGB output.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for MIPI DSI input
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for MIPI DPI output (panel or connector).
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - enable-gpios
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    dsi {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      bridge@0 {
+        compatible = "chipone,icn6211";
+        reg = <0>;
+        enable-gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* LCD-RST: PL5 */
+
+        ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          port@0 {
+            reg = <0>;
+
+            bridge_in_dsi: endpoint {
+              remote-endpoint = <&dsi_out_bridge>;
+            };
+          };
+
+          port@1 {
+            reg = <1>;
+
+            bridge_out_panel: endpoint {
+              remote-endpoint = <&panel_out_bridge>;
+            };
+          };
+        };
+      };
+    };
MAINTAINERS +5 -1
index 4b705ba51c54..b9d11101d060 100644
@@ -5568,6 +5568,11 @@ S:       Maintained
 F:     Documentation/devicetree/bindings/display/panel/boe,himax8279d.yaml
 F:     drivers/gpu/drm/panel/panel-boe-himax8279d.c
 
+DRM DRIVER FOR CHIPONE ICN6211 MIPI-DSI to RGB CONVERTER BRIDGE
+M:     Jagan Teki <[email protected]>
+S:     Maintained
+F:     Documentation/devicetree/bindings/display/bridge/chipone,icn6211.yaml
+
 DRM DRIVER FOR FARADAY TVE200 TV ENCODER
 M:     Linus Walleij <[email protected]>
 S:     Maintained
--
Quoted 2 lines

2.25.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel