arm: dts: imx8mp: Generate single bootable binary
Subsystems (2)
PATCH 1/1 arm: dts: imx8mp: Generate single bootable binary
binman conversion made flashing flash.bin
and u-boot.itb necessary. Update binman config
to create a single flash.bin image again.
This updates imx8mp_evk and phyCORE-i.MX8MP as they share the same binman config.
Updated also imx8mp_evk documentation.
Tested on phyCORE-i.MX8MP.
--- arch/arm/dts/imx8mp-u-boot.dtsi | 17 ++++++++++++++++- .../imx8mp_evk/imximage-8mp-lpddr4.cfg | 2 +- board/phytec/phycore_imx8mp/imximage-8mp-sd.cfg | 2 +- doc/board/nxp/imx8mp_evk.rst | 1 - 4 files changed, 18 insertions(+), 4 deletions(-)
arch/arm/dts/imx8mp-u-boot.dtsi +16 -1
@@ -82,7 +82,7 @@ }; }; - flash { + spl { mkimage { args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x920000";
@@ -149,4 +149,19 @@ }; }; }; + + imx-boot { + filename = "flash.bin"; + pad-byte = <0x00>; + + spl: blob-ext@1 { + filename = "spl.bin"; + offset = <0x0>; + }; + + uboot: blob-ext@2 { + filename = "u-boot.itb"; + offset = <0x58000>; + }; + }; };
board/freescale/imx8mp_evk/imximage-8mp-lpddr4.cfg +1 -1
@@ -7,4 +7,4 @@ ROM_VERSION v2 BOOT_FROM sd -LOADER mkimage.flash.mkimage 0x920000 +LOADER mkimage.spl.mkimage 0x920000
board/phytec/phycore_imx8mp/imximage-8mp-sd.cfg +1 -1
@@ -7,4 +7,4 @@ ROM_VERSION v2 BOOT_FROM sd -LOADER mkimage.flash.mkimage 0x920000 +LOADER mkimage.spl.mkimage 0x920000
doc/board/nxp/imx8mp_evk.rst +0 -1
@@ -52,7 +52,6 @@ Burn the flash.bin to the MicroSD card at offset 32KB: .. code-block:: bash $sudo dd if=build/flash.bin of=/dev/sd[x] bs=1K seek=32 conv=notrunc; sync - $sudo dd if=build/u-boot.itb of=/dev/sd[x] bs=1K seek=384 conv=notrunc; sync Boot ----
Signature · 1 line
2.25.1
Hi Teresa,
Quoted 11 lines · Teresa Remmet
binman conversion made flashing flash.bin
and u-boot.itb necessary. Update binman config
to create a single flash.bin image again.This updates
imx8mp_evkand phyCORE-i.MX8MP as they share the same binman config.Updated also
imx8mp_evkdocumentation.Tested on phyCORE-i.MX8MP.
Thanks for taking care of this.
Quoted 13 lines
Signed-off-by Teresa Remmet <[email protected]>--- arch/arm/dts/imx8mp-u-boot.dtsi | 17 ++++++++++++++++- .../imx8mp_evk/imximage-8mp-lpddr4.cfg | 2 +- board/phytec/phycore_imx8mp/imximage-8mp-sd.cfg | 2 +- doc/board/nxp/imx8mp_evk.rst | 1 - 4 files changed, 18 insertions(+), 4 deletions(-)arch/arm/dts/imx8mp-u-boot.dtsi +0
-0
arch/arm/dts/imx8mp-u-boot.dtsi line 85
Quoted 5 lines
arch/arm/dts/imx8mp-u-boot.dtsi +1
-1@@ -82,7 +82,7 @@ }; }; - flash { + spl {
To make this more standard, could you please also pass 'filename = "spl.bin" here too?
Please check:
https://lists.denx.de/pipermail/u-boot/2021-August/458754.html
arch/arm/dts/imx8mp-u-boot.dtsi line 87
Quoted 3 lines
arch/arm/dts/imx8mp-u-boot.dtsi +1
-1BOOT_FROM sd -LOADER mkimage.flash.mkimage 0x920000 +LOADER mkimage.spl.mkimage 0x920000
Please use "LOADER u-boot-spl-ddr.bin 0x920000" here instead.
board/phytec/phycore_imx8mp/imximage-8mp-sd.cfg line 10
Quoted 10 lines
board/phytec/phycore_imx8mp/imximage-8mp-sd.cfg +1
-1@@ -7,4 +7,4 @@ ROM_VERSION v2 BOOT_FROM sd -LOADER mkimage.flash.mkimage 0x920000 +LOADER mkimage.spl.mkimage 0x920000
Ditto.
With these changes, you can add:
Thanks
Am Mittwoch, den 25.08.2021, 12:56 -0300 schrieb Fabio Estevam:
Quoted 35 lines
Hi Teresa,
Quoted 10 lines · Teresa Remmet
binman conversion made flashing flash.bin
and u-boot.itb necessary. Update binman config
to create a single flash.bin image again.This updates
imx8mp_evkand phyCORE-i.MX8MP as they share the same binman config.Updated also
imx8mp_evkdocumentation.Tested on phyCORE-i.MX8MP.
Thanks for taking care of this.
Quoted 18 lines
Signed-off-by Teresa Remmet <[email protected]>--- arch/arm/dts/imx8mp-u-boot.dtsi | 17 ++++++++++++++++- .../imx8mp_evk/imximage-8mp-lpddr4.cfg | 2 +- board/phytec/phycore_imx8mp/imximage-8mp-sd.cfg | 2 +- doc/board/nxp/imx8mp_evk.rst | 1 - 4 files changed, 18 insertions(+), 4 deletions(-)arch/arm/dts/imx8mp- renamed from arch/arm/dts/imx8mp-u-boot.dtsi +0
-0
u-boot.dtsi
indexa6ede2ed6e30..ace7b2051e7f100644arch/arm/dts/imx8mp-u-boot.dtsi +0
-0@@ -82,7 +82,7 @@ }; };
Quoted 8 lines
arch/arm/dts/imx8mp-u-boot.dtsi line 85
Quoted 2 lines
arch/arm/dts/imx8mp-u-boot.dtsi +1
-1- flash { + spl {To make this more standard, could you please also pass 'filename = "spl.bin" here too?
Please check:
https://lists.denx.de/pipermail/u-boot/2021-August/458754.html
Oh, I missed the latest version of your patch. I will update this accordingly. Thanks.
Teresa
Quoted 26 lines
arch/arm/dts/imx8mp-u-boot.dtsi line 87
Quoted 4 lines
arch/arm/dts/imx8mp-u-boot.dtsi +1
-1BOOT_FROM sd -LOADER mkimage.flash.mkimage 0x920000 +LOADER mkimage.spl.mkimage 0x920000Please use "LOADER u-boot-spl-ddr.bin
0x920000" here instead.board/phytec/phycore_imx8mp/imximage-8mp-sd.cfg line 10
Quoted 11 lines
board/phytec/phycore_imx8mp/imximage-8mp-sd.cfg +1
-1@@ -7,4 +7,4 @@ ROM_VERSION v2 BOOT_FROM sd -LOADER mkimage.flash.mkimage 0x920000 +LOADER mkimage.spl.mkimage 0x920000Ditto.
With these changes, you can add:
Reviewed-by Fabio Estevam <[email protected]>Thanks
Hello Teresa,
Quoted 11 lines · Teresa Remmet
binman conversion made flashing flash.bin
and u-boot.itb necessary. Update binman config
to create a single flash.bin image again.This updates
imx8mp_evkand phyCORE-i.MX8MP as they share the same binman config.Updated also
imx8mp_evkdocumentation.Tested on phyCORE-i.MX8MP.
Quoted 7 lines
Signed-off-by Teresa Remmet <[email protected]>--- arch/arm/dts/imx8mp-u-boot.dtsi | 17 ++++++++++++++++- .../imx8mp_evk/imximage-8mp-lpddr4.cfg | 2 +- board/phytec/phycore_imx8mp/imximage-8mp-sd.cfg | 2 +- doc/board/nxp/imx8mp_evk.rst | 1 - 4 files changed, 18 insertions(+), 4 deletions(-)
No more comments beside Fabios, so
bye,
Heiko
Signature · 3 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-52 Fax: +49-8142-66989-80 Email: [email protected]