RZN1 USB Host support
Subsystems (5)
cover RZN1 USB Host support
Hi,
This series add support for the USB Host controllers available on RZN1 (r9a06g032) SOC.
These USB Host controllers are PCI OHCI/EHCI controllers located behind a bridge.
Regards,
Herve
Herve Codina (6):
PCI: rcar-gen2: Add support for clocks
dt-bindings: PCI: pci-rcar-gen2: Add device tree support for r9a06g032
PCI: rcar-gen2: Add R9A06G032 support
ARM: dts: r9a06g032: Add internal PCI bridge node
ARM: dts: r9a06g032: Add USB PHY DT support
ARM: dts: r9a06g032: Link the PCI USB devices to the USB PHY
.../devicetree/bindings/pci/pci-rcar-gen2.txt | 4 +- arch/arm/boot/dts/r9a06g032.dtsi | 46 +++++++++++++++++++ drivers/pci/controller/pci-rcar-gen2.c | 30 +++++++++++- 3 files changed, 77 insertions(+), 3 deletions(-)
Signature · 1 line
2.35.1
PATCH 1/6 PCI: rcar-gen2: Add support for clocks
The PCI rcar-gen2 does not call any clk_prepare_enable(). This lead to an access failure when the driver tries to access the IP (at least on a RZ/N1D platform).
Prepare and enable clocks using the bulk version of clk_prepare_enable() in order to prepare and enable all clocks attached to this device.
--- drivers/pci/controller/pci-rcar-gen2.c | 28 ++++++++++++++++++++++++-- 1 file changed, 26 insertions(+), 2 deletions(-)
drivers/pci/controller/pci-rcar-gen2.c +26 -2
@@ -8,6 +8,7 @@* Author: Valentine Barshak <[email protected]> */ +#include <linux/clk.h> #include <linux/delay.h> #include <linux/init.h> #include <linux/interrupt.h>
@@ -99,6 +100,8 @@ struct rcar_pci {struct resource mem_res;struct resource *cfg_res;int irq; +struct clk_bulk_data *clocks; +int nclocks; };/* PCI configuration space operations */
@@ -282,6 +285,7 @@ static int rcar_pci_probe(struct platform_device *pdev)struct rcar_pci *priv;struct pci_host_bridge *bridge;void __iomem *reg; +int ret; bridge =devm_pci_alloc_host_bridge (dev,sizeof (*priv));if (!bridge)
@@ -305,13 +309,25 @@ static int rcar_pci_probe(struct platform_device *pdev) priv->mem_res = *mem_res; priv->cfg_res = cfg_res; + ret =devm_clk_bulk_get_all (dev, &priv->clocks); +if (ret <0 ) { +dev_err (dev,"failed to get clocks %d\n" , ret); +return ret; + } + priv->nclocks = ret; + + ret =clk_bulk_prepare_enable (priv->nclocks, priv->clocks); +if (ret) +return ret; + priv->irq =platform_get_irq (pdev,0 ); priv->reg = reg; priv->dev = dev;if (priv->irq <0 ) {dev_err (dev,"no valid irq found\n" ); -return priv->irq; + ret = priv->irq; + goto disable_clocks; } bridge->ops = &rcar_pci_ops;
@@ -320,7 +336,15 @@ static int rcar_pci_probe(struct platform_device *pdev)rcar_pci_setup (priv); -return pci_host_probe (bridge); + ret =pci_host_probe (bridge); +if (ret <0 ) + goto disable_clocks; + +return 0 ; + +disable_clocks: +clk_bulk_disable_unprepare (priv->nclocks, priv->clocks); +return ret; }static const struct of_device_id rcar_pci_of_match[] = {
Signature · 1 line
2.35.1
Rob Herring
maintainerRe: [PATCH 1/6] PCI: rcar-gen2: Add support for clocks
Quoted 7 lines · Herve Codina
The PCI rcar-gen2 does not call any
clk_prepare_enable(). This lead to an access failure when the driver tries to access the IP (at least on a RZ/N1D platform).Prepare and enable clocks using the bulk version of
clk_prepare_enable()in order to prepare and enable all clocks attached to this device.
The binding says there is only a single clock, so it needs an update if there are multiple clocks. (And ideally converted to DT schema format.)
Rob
Re: [PATCH 1/6] PCI: rcar-gen2: Add support for clocks
Hi Rob,
Quoted 11 lines · On Tue, 12 Apr 2022 10:50:10 -0500 Rob Herring <[email protected]> wrote:
Quoted 7 lines · Herve Codina
The PCI rcar-gen2 does not call any
clk_prepare_enable(). This lead to an access failure when the driver tries to access the IP (at least on a RZ/N1D platform).Prepare and enable clocks using the bulk version of
clk_prepare_enable()in order to prepare and enable all clocks attached to this device.The binding says there is only a single clock, so it needs an update if there are multiple clocks. (And ideally converted to DT schema format.)
Indeed, I will convert to DT schema format and update the clocks property description.
Regards,
Hervé
PATCH 2/6 dt-bindings: PCI: pci-rcar-gen2: Add device tree support for r9a06g032
In reply to Herve CodinaAdd internal PCI bridge support for the r9a06g032 SoC. The Renesas RZ/N1D (R9A06G032) internal PCI bridge is compatible with the one present in the R-Car Gen2 family.
--- Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt +3 -1
@@ -15,7 +15,9 @@ Required properties: "renesas,pci-r8a7793" for the R8A7793 SoC; "renesas,pci-r8a7794" for the R8A7794 SoC; "renesas,pci-rcar-gen2" for a generic R-Car Gen2 or - RZ/G1 compatible device. + RZ/G1 compatible device; + "renesas,pci-r9a06g032" for the R9A06G032 (RZ/N1D) SoC; + "renesas,pci-rzn1" for a generic RZ/N1 compatible device. When compatible with the generic version, nodes must list the
Signature · 1 line
2.35.1
PATCH 3/6 PCI: rcar-gen2: Add R9A06G032 support
In reply to Herve CodinaAdd Renesas R9A06G032 SoC support to the Renesas R-Car gen2 PCI bridge driver.
The Renesas RZ/N1D (R9A06G032) internal PCI bridge is compatible with the one available in the R-Car Gen2 family.
--- drivers/pci/controller/pci-rcar-gen2.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/pci/controller/pci-rcar-gen2.c +2 -0
@@ -352,6 +352,8 @@ static const struct of_device_id rcar_pci_of_match[] = { { .compatible = "renesas,pci-r8a7791", }, { .compatible = "renesas,pci-r8a7794", }, { .compatible = "renesas,pci-rcar-gen2", }, + { .compatible = "renesas,pci-r9a06g032", }, + { .compatible = "renesas,pci-rzn1", }, { }, };
Signature · 1 line
2.35.1
Re: [PATCH 3/6] PCI: rcar-gen2: Add R9A06G032 support
Hi Herve,
[email protected] wrote on Tue, 12 Apr 2022 11:40:26 +0200:
Quoted 15 lines
Add Renesas R9A06G032 SoC support to the Renesas R-Car gen2 PCI bridge driver.
The Renesas RZ/N1D (R9A06G032) internal PCI bridge is compatible with the one available in the R-Car Gen2 family.Signed-off-by Herve Codina <[email protected]>--- drivers/pci/controller/pci-rcar-gen2.c | 2 ++ 1 file changed, 2 insertions(+)drivers/pci/controller/pci-rcar-gen2.c +0
-0
drivers/pci/controller/pci-rcar-gen2.c static const struct of_device_id rcar_pci_of_match[] = { · line 356
Quoted 5 lines
drivers/pci/controller/pci-rcar-gen2.c +2
-0@@ -352,6 +352,8 @@ static const struct of_device_id rcar_pci_of_match[] = { { .compatible = "renesas,pci-r8a7791", }, { .compatible = "renesas,pci-r8a7794", }, { .compatible = "renesas,pci-rcar-gen2", }, + { .compatible = "renesas,pci-r9a06g032", }, + { .compatible = "renesas,pci-rzn1", },
I don't think you don't yet need to match against the two, matching against pci-rzn1 is enough for now, until we discover that something is specific in the r9a06g032 family and we need to handle something else of course.
Thanks,
Miquèl
Re: [PATCH 3/6] PCI: rcar-gen2: Add R9A06G032 support
In reply to Herve CodinaHello!
Quoted 15 lines · Herve Codina
Add Renesas R9A06G032 SoC support to the Renesas R-Car gen2 PCI bridge driver.
The Renesas RZ/N1D (R9A06G032) internal PCI bridge is compatible with the one available in the R-Car Gen2 family.Signed-off-by Herve Codina <[email protected]>--- drivers/pci/controller/pci-rcar-gen2.c | 2 ++ 1 file changed, 2 insertions(+)drivers/pci/controller/pci-rcar-gen2.c +0
-0
drivers/pci/controller/pci-rcar-gen2.c static const struct of_device_id rcar_pci_of_match[] = { · line 355
Quoted 4 lines
drivers/pci/controller/pci-rcar-gen2.c +1
-0@@ -352,6 +352,8 @@ static const struct of_device_id rcar_pci_of_match[] = { { .compatible = "renesas,pci-r8a7791", }, { .compatible = "renesas,pci-r8a7794", }, { .compatible = "renesas,pci-rcar-gen2", }, + { .compatible = "renesas,pci-r9a06g032", },
Do we really need this one here? Isn't it covered by the next item?
drivers/pci/controller/pci-rcar-gen2.c static const struct of_device_id rcar_pci_of_match[] = { · line 359
Quoted 4 lines
drivers/pci/controller/pci-rcar-gen2.c +1
-0+ { .compatible = "renesas,pci-rzn1", }, { }, };
MBR, Sergey
Re: [PATCH 3/6] PCI: rcar-gen2: Add R9A06G032 support
Hi Sergey,
Quoted 14 lines · On Wed, 13 Apr 2022 12:08:01 +0300 Sergey Shtylyov <[email protected]> wrote:
Hello!
Quoted 10 lines · Herve Codina
Add Renesas R9A06G032 SoC support to the Renesas R-Car gen2 PCI bridge driver.
The Renesas RZ/N1D (R9A06G032) internal PCI bridge is compatible with the one available in the R-Car Gen2 family.Signed-off-by Herve Codina <[email protected]>--- drivers/pci/controller/pci-rcar-gen2.c | 2 ++ 1 file changed, 2 insertions(+)
Quoted 11 lines
drivers/pci/controller/pci-rcar-gen2.c static const struct of_device_id rcar_pci_of_match[] = { · line 355
Quoted 9 lines
drivers/pci/controller/pci-rcar-gen2.c +1
-0@@ -352,6 +352,8 @@ static const struct of_device_id rcar_pci_of_match[] = { { .compatible = "renesas,pci-r8a7791", }, { .compatible = "renesas,pci-r8a7794", }, { .compatible = "renesas,pci-rcar-gen2", }, + { .compatible = "renesas,pci-r9a06g032", },Do we really need this one here? Isn't it covered by the next item?
Yes, this one is not needed.
Miquèl did the same remark too.
I will remove '.compatible = "renesas,pci-r9a06g032"' in v2.
Regards,
Herve
Quoted 6 lines
Quoted 5 lines
drivers/pci/controller/pci-rcar-gen2.c +1
-0+ { .compatible = "renesas,pci-rzn1", }, { }, };
PATCH 4/6 ARM: dts: r9a06g032: Add internal PCI bridge node
In reply to Herve CodinaAdd the device node for the r9a06g032 internal PCI bridge device.
--- arch/arm/boot/dts/r9a06g032.dtsi | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+)
arch/arm/boot/dts/r9a06g032.dtsi +28 -0
@@ -211,6 +211,34 @@ gic: interrupt-controller@44101000 { interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>; }; + + pci_usb: pci@40030000 { + compatible = "renesas,pci-r9a06g032", "renesas,pci-rzn1"; + device_type = "pci"; + clocks = <&sysctrl R9A06G032_HCLK_USBH>, + <&sysctrl R9A06G032_HCLK_USBPM>, + <&sysctrl R9A06G032_CLK_PCI_USB>; + clock-names = "hclk_usbh", "hclk_usbpm", "clk_pci_usb"; + reg = <0x40030000 0xc00>, + <0x40020000 0x1100>; + interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + + bus-range = <0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x02000000 0 0x40020000 0x40020000 0 0x00010000>; + /* Should map all possible DDR as inbound ranges, but + * the IP only supports a 256MB, 512MB, or 1GB window. + * flags, PCI addr (64-bit), CPU addr, PCI size (64-bit) + */ + dma-ranges = <0x42000000 0 0x80000000 0x80000000 0 0x40000000>; + interrupt-map-mask = <0xff00 0 0 0x7>; + interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH + 0x0800 0 0 1 &gic GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH + 0x1000 0 0 2 &gic GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; + }; }; timer {
Signature · 1 line
2.35.1
PATCH 5/6 ARM: dts: r9a06g032: Add USB PHY DT support
In reply to Herve CodinaDefine the r9a06g032 generic part of the USB PHY device node.
--- arch/arm/boot/dts/r9a06g032.dtsi | 6 ++++++ 1 file changed, 6 insertions(+)
arch/arm/boot/dts/r9a06g032.dtsi +6 -0
@@ -59,6 +59,12 @@ ext_rtc_clk: extrtcclk { clock-frequency = <0>; }; + usbphy: usbphy { + #phy-cells = <0>; + compatible = "usb-nop-xceiv"; + status = "disabled"; + }; + soc { compatible = "simple-bus"; #address-cells = <1>;
Signature · 1 line
2.35.1
PATCH 6/6 ARM: dts: r9a06g032: Link the PCI USB devices to the USB PHY
In reply to Herve CodinaDescribe the PCI USB devices that are behind the PCI bridge, adding necessary links to the USB PHY device.
--- arch/arm/boot/dts/r9a06g032.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+)
arch/arm/boot/dts/r9a06g032.dtsi +12 -0
@@ -244,6 +244,18 @@ pci_usb: pci@40030000 { interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH 0x0800 0 0 1 &gic GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH 0x1000 0 0 2 &gic GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; + + usb@1,0 { + reg = <0x800 0 0 0 0>; + phys = <&usbphy 0>; + phy-names = "usb"; + }; + + usb@2,0 { + reg = <0x1000 0 0 0 0>; + phys = <&usbphy 0>; + phy-names = "usb"; + }; }; };
Signature · 1 line
2.35.1