Skip to contentSkip to conversation

Improve AST26x0 DDR4 timing and signal quality

PATCH In review Dylan Hung 3 participants 10 messages Nov 11, 2022 – Nov 24, 2022

Subsystems (2)
lore
Share & tools
lore

Dylan Hung

author
#0 lore raw

cover Improve AST26x0 DDR4 timing and signal quality

This patch series fine-tunes the read & write DQS/DQ timing, CLK/CA timing and termination (RTT_NOM, RTT_PARK and RTT_WR) for Aspeed AST26x0 SOC to get better signal quality and hence improve the stability. Also, a typing error of the DDR-PHY status polling is fixed.

Dylan Hung (3):
ram: ast2600: Fix incorrect statement of the register polling
ram: ast2600: Improve ddr4 timing and signal quality
ram: ast2600: Align the RL and WL setting

 .../include/asm/arch-aspeed/sdram_ast2600.h   |   4 +
 drivers/ram/aspeed/sdram_ast2600.c            | 179 +++++++++++++++---
 2 files changed, 152 insertions(+), 31 deletions(-)
Signature · 1 line
2.25.1
author
#4 lore raw

PATCH 2/3 ram: ast2600: Improve ddr4 timing and signal quality

Adjust the following settings to get better timing and signal quality.

1. write DQS/DQ delay
- 1e6e2304[0]
- 1e6e2304[15:8]

2. read DQS/DQ delay
- 0x1e6e0298[0]
- 0x1e6e0298[15:8]

3. CLK/CA timing
- 0x1e6e01a8[31]

4. Read and write termination
- change RTT_ROM from 40 ohm to 48 ohm (MR1[10:8])
- change RTT_PARK from disable to 48 ohm (MR5[8:6])
- change RTT_WR from 120 ohm to disable (MR2[11:9])
- change PHY ODT from 40 ohm to 80 ohm (0x1e6e0130[10:8])

Note1: Both DDR-PHY and DDR controller have their own registers for DDR4 Mode Registers (MR0~MR6). This patch introduces macros to synchronize the MR value on both sides.

Note2: the waveform meansurement can be found in item #21 of Aspeed AST26x0 Application note (AP note).

---
 drivers/ram/aspeed/sdram_ast2600.c | 163 ++++++++++++++++++++++++-----
 1 file changed, 138 insertions(+), 25 deletions(-)
drivers/ram/aspeed/sdram_ast2600.c +138 -25
index b09232a30413..bda02d062900 100644
@@ -20,6 +20,119 @@
 #define DDR_PHY_TBL_CHG_ADDR            0xaeeddeea
 #define DDR_PHY_TBL_END                 0xaeededed
 
+/**
+ * phyr030[18:16] - Ron PU (PHY side)
+ * phyr030[14:12] - Ron PD (PHY side)
+ *   b'000 : disable
+ *   b'001 : 240 ohm
+ *   b'010 : 120 ohm
+ *   b'011 : 80 ohm
+ *   b'100 : 60 ohm
+ *   b'101 : 48 ohm
+ *   b'110 : 40 ohm
+ *   b'111 : 34 ohm (default)
+ */
+#define PHY_RON				((0x7 << 16) | (0x7 << 12))
+
+/**
+ * phyr030[10:8] - ODT configuration (PHY side)
+ *   b'000 : ODT disabled
+ *   b'001 : 240 ohm
+ *   b'010 : 120 ohm
+ *   b'011 : 80 ohm (default)
+ *   b'100 : 60 ohm
+ *   b'101 : 48 ohm
+ *   b'110 : 40 ohm
+ *   b'111 : 34 ohm
+ */
+#define PHY_ODT				(0x3 << 8)
+
+/**
+ * MR1[2:1] output driver impedance
+ *   b'00 : 34 ohm (default)
+ *   b'01 : 48 ohm
+ */
+#define DRAM_RON			(0x0 << 1)
+
+/**
+ * DRAM ODT - synchronous ODT mode
+ *   RTT_WR: disable
+ *   RTT_NOM = RTT_PARK
+ *
+ * MR1[10:8] RTT_NOM
+ *   b'000 : RTT_NOM disable
+ *   b'001 : 60 ohm
+ *   b'010 : 120 ohm
+ *   b'011 : 40 ohm
+ *   b'100 : 240 ohm
+ *   b'101 : 48 ohm  (default)
+ *   b'110 : 80 ohm
+ *   b'111 : 34 ohm
+ *
+ * MR5[8:6] RTT_PARK
+ *   b'000 : RTT_PARK disable
+ *   b'001 : 60 ohm
+ *   b'010 : 120 ohm
+ *   b'011 : 40 ohm
+ *   b'100 : 240 ohm
+ *   b'101 : 48 ohm  (default)
+ *   b'110 : 80 ohm
+ *   b'111 : 34 ohm
+ *
+ * MR2[11:9] RTT_WR
+ *   b'000 : Dynamic ODT off  (default)
+ *   b'001 : 120 ohm
+ *   b'010 : 240 ohm
+ *   b'011 : Hi-Z
+ *   b'100 : 80 ohm
+ */
+#define RTT_WR				(0x0 << 9)
+#define RTT_NOM				(0x5 << 8)
+#define RTT_PARK			(0x5 << 6)
+
+/**
+ * MR6[6] VrefDQ training range
+ *   b'0 : range 1
+ *   b'1 : range 2 (default)
+ */
+#define VREFDQ_RANGE_2			BIT(6)
+
+/**
+ * Latency setting:
+ * AL = PL = 0 (hardware fixed setting)
+ * -> WL = AL + CWL + PL = CWL
+ * -> RL = AL + CL + PL = CL
+ */
+#define CONFIG_WL			9
+#define CONFIG_RL			12
+#define T_RDDATA_EN			((CONFIG_RL - 2) << 8)
+#define T_PHY_WRLAT			(CONFIG_WL - 2)
+
+/* MR0 */
+#define MR0_CL_12			(BIT(4) | BIT(2))
+#define MR0_WR12_RTP6			BIT(9)
+#define MR0_DLL_RESET			BIT(8)
+#define MR0_VAL				(MR0_CL_12 | MR0_WR12_RTP6 | MR0_DLL_RESET)
+
+/* MR1 */
+#define MR1_VAL				(0x0001 | RTT_NOM | DRAM_RON)
+
+/* MR2 */
+#define MR2_CWL_9			0
+#define MR2_VAL				(0x0000 | RTT_WR | MR2_CWL_9)
+
+/* MR3 ~ MR6 */
+#define MR3_VAL				0x0000
+#define MR4_VAL				0x0000
+#define MR5_VAL				(0x0400 | RTT_PARK)
+#define MR6_VAL				0x0400
+
+/**
+ * The offset value applied to the DDR PHY write data eye training result
+ * to fine-tune the write DQ/DQS alignment
+ */
+#define WR_DATA_EYE_OFFSET		(0x10 << 8)
+
 #if defined(CONFIG_ASPEED_DDR4_800)
 u32 ast2600_sdramphy_config[165] = {
 	0x1e6e0100,	// start address
@@ -35,7 +148,7 @@ u32 ast2600_sdramphy_config[165] = {
 	0x20000000,	// phyr024
 	0x00000008,	// phyr028
 	0x00000000,	// phyr02c
-	0x00077600,	// phyr030
+	(PHY_RON | PHY_ODT),	/* phyr030 */
 	0x00000000,	// phyr034
 	0x00000000,	// phyr038
 	0x20000000,	// phyr03c
@@ -44,18 +157,18 @@ u32 ast2600_sdramphy_config[165] = {
 	0x00002f07,	// phyr048
 	0x00003080,	// phyr04c
 	0x04000000,	// phyr050
-	0x00000200,	// phyr054
-	0x03140201,	// phyr058
-	0x04800000,	// phyr05c
-	0x0800044e,	// phyr060
+	((MR3_VAL << 16) | MR2_VAL),	/* phyr054 */
+	((MR0_VAL << 16) | MR1_VAL),	/* phyr058 */
+	((MR5_VAL << 16) | MR4_VAL),	/* phyr05c */
+	((0x0800 << 16) | MR6_VAL | VREFDQ_RANGE_2 | 0xe), /* phyr060 */
 	0x00000000,	// phyr064
 	0x00180008,	// phyr068
 	0x00e00400,	// phyr06c
 	0x00140206,	// phyr070
 	0x1d4c0000,	// phyr074
-	0x493e0107,	// phyr078
+	(0x493e0100 | T_PHY_WRLAT),	/* phyr078 */
 	0x08060404,	// phyr07c
-	0x90000a00,	// phyr080
+	(0x90000000 | T_RDDATA_EN),	/* phyr080 */
 	0x06420618,	// phyr084
 	0x00001002,	// phyr088
 	0x05701016,	// phyr08c
@@ -94,7 +207,7 @@ u32 ast2600_sdramphy_config[165] = {
 	0x20202020,	// phyr09c
 	0x20202020,	// phyr0a0
 	0x00002020,	// phyr0a4
-	0x80000000,	// phyr0a8
+	0x00000000,	/* phyr0a8 */
 	0x00000001,	// phyr0ac
 	0xaeeddeea,	// change address
 	0x1e6e0318,	// new address
@@ -154,7 +267,7 @@ u32 ast2600_sdramphy_config[165] = {
 	0x20202020,	// phyr170
 	0xaeeddeea,	// change address
 	0x1e6e0298,	// new address
-	0x20200800,	// phyr198
+	0x20200000,	/* phyr198 */
 	0x20202020,	// phyr19c
 	0x20202020,	// phyr1a0
 	0x20202020,	// phyr1a4
@@ -177,7 +290,7 @@ u32 ast2600_sdramphy_config[165] = {
 	0x00002020,	// phyr1e8
 	0xaeeddeea,	// change address
 	0x1e6e0304,	// new address
-	0x00000800,	// phyr204
+	(0x00000001 | WR_DATA_EYE_OFFSET), /* phyr204 */
 	0xaeeddeea,	// change address
 	0x1e6e027c,	// new address
 	0x4e400000,	// phyr17c
@@ -203,7 +316,7 @@ u32 ast2600_sdramphy_config[165] = {
 	0x20000000,	// phyr024
 	0x00000008,	// phyr028
 	0x00000000,	// phyr02c
-	0x00077600,	// phyr030
+	(PHY_RON | PHY_ODT),	/* phyr030 */
 	0x00000000,	// phyr034
 	0x00000000,	// phyr038
 	0x20000000,	// phyr03c
@@ -212,18 +325,18 @@ u32 ast2600_sdramphy_config[165] = {
 	0x00002f07,	// phyr048
 	0x00003080,	// phyr04c
 	0x04000000,	// phyr050
-	0x00000200,	// phyr054
-	0x03140501,	// phyr058-rtt:40
-	0x04800000,	// phyr05c
-	0x0800044e,	// phyr060
+	((MR3_VAL << 16) | MR2_VAL),	/* phyr054 */
+	((MR0_VAL << 16) | MR1_VAL),	/* phyr058 */
+	((MR5_VAL << 16) | MR4_VAL),	/* phyr05c */
+	((0x0800 << 16) | MR6_VAL | VREFDQ_RANGE_2 | 0xe), /* phyr060 */
 	0x00000000,	// phyr064
 	0x00180008,	// phyr068
 	0x00e00400,	// phyr06c
 	0x00140206,	// phyr070
 	0x1d4c0000,	// phyr074
-	0x493e0107,	// phyr078
+	(0x493e0100 | T_PHY_WRLAT),	/* phyr078 */
 	0x08060404,	// phyr07c
-	0x90000a00,	// phyr080
+	(0x90000000 | T_RDDATA_EN),	/* phyr080 */
 	0x06420c30,	// phyr084
 	0x00001002,	// phyr088
 	0x05701016,	// phyr08c
@@ -256,13 +369,13 @@ u32 ast2600_sdramphy_config[165] = {
 	0x00000000,	// phyr200
 	0xaeeddeea,	// change address
 	0x1e6e0194,	// new address
-	0x801112e0,	// phyr094 - bit12=1,15=0,- write window is ok
+	0x801112e0,	// phyr094
 	0xaeeddeea,	// change address
 	0x1e6e019c,	// new address
 	0x20202020,	// phyr09c
 	0x20202020,	// phyr0a0
 	0x00002020,	// phyr0a4
-	0x80000000,	// phyr0a8
+	0x00000000,	/* phyr0a8 */
 	0x00000001,	// phyr0ac
 	0xaeeddeea,	// change address
 	0x1e6e0318,	// new address
@@ -322,7 +435,7 @@ u32 ast2600_sdramphy_config[165] = {
 	0x20202020,	// phyr170
 	0xaeeddeea,	// change address
 	0x1e6e0298,	// new address
-	0x20200800,	// phyr198
+	0x20200000,	/* phyr198 */
 	0x20202020,	// phyr19c
 	0x20202020,	// phyr1a0
 	0x20202020,	// phyr1a4
@@ -345,7 +458,7 @@ u32 ast2600_sdramphy_config[165] = {
 	0x00002020,	// phyr1e8
 	0xaeeddeea,	// change address
 	0x1e6e0304,	// new address
-	0x00000800,	// phyr204
+	(0x00000001 | WR_DATA_EYE_OFFSET), /* phyr204 */
 	0xaeeddeea,	// change address
 	0x1e6e027c,	// new address
 	0x4e400000,	// phyr17c
@@ -388,10 +501,10 @@ u32 ast2600_sdramphy_config[165] = {
  * AC timing and SDRAM mode register setting
  * for real chip are derived from the model GDDR4-1600
  */
-#define DDR4_MR01_MODE	0x03010510
-#define DDR4_MR23_MODE	0x00000000
-#define DDR4_MR45_MODE	0x04000000
-#define DDR4_MR6_MODE	0x00000400
+#define DDR4_MR01_MODE	((MR1_VAL << 16) | MR0_VAL)
+#define DDR4_MR23_MODE	((MR3_VAL << 16) | MR2_VAL)
+#define DDR4_MR45_MODE	((MR5_VAL << 16) | MR4_VAL)
+#define DDR4_MR6_MODE	MR6_VAL
 #define DDR4_TRFC_1600	0x467299f1
 #define DDR4_TRFC_1333	0x3a5f80c9
 #define DDR4_TRFC_800	0x23394c78
Signature · 1 line
2.25.1
author
#1 lore raw

PATCH 1/3 ram: ast2600: Fix incorrect statement of the register polling

In reply to Dylan Hung

The condition "~data" in the if-statement is a typo. The original intention is to poll if SDRAM_PHYCTRL0_INIT bit equals to 0. So use "data == 0" for instead.

Besides, the bit[1] of "phy_status" register is hardwired to SDRAM_PHYCTRL0_INIT (with inverse logic). Since SDRAM_PHYCTRL0_INIT has already done, remove the unnecessary checking of phy_status[1].

Fixes fde93143469f ("ram: aspeed: Add AST2600 DRAM control support")
---
 drivers/ram/aspeed/sdram_ast2600.c | 7 +------
 1 file changed, 1 insertion(+), 6 deletions(-)
drivers/ram/aspeed/sdram_ast2600.c +1 -6
index 9ad398d24155..b09232a30413 100644
@@ -449,7 +449,7 @@ static void ast2600_sdramphy_kick_training(struct dram_info *info)
 
 	while (1) {
 		data = readl(&regs->phy_ctrl[0]) & SDRAM_PHYCTRL0_INIT;
-		if (~data)
+		if (data == 0)
 			break;
 	}
 }
@@ -984,11 +984,6 @@ static int ast2600_sdrammc_probe(struct udevice *dev)
 L_ast2600_sdramphy_train:
 	ast2600_sdrammc_init_ddr4(priv);
 
-	/* make sure DDR-PHY is ready before access */
-	do {
-		reg = readl(priv->phy_status) & BIT(1);
-	} while (reg == 0);
-
 	if (ast2600_sdramphy_check_status(priv) != 0) {
 		printf("DDR4 PHY training fail, retrain\n");
 		goto L_ast2600_sdramphy_train;
Signature · 1 line
2.25.1
author
#7 lore raw

PATCH 3/3 ram: ast2600: Align the RL and WL setting

In reply to Dylan Hung

Use macro to represent the RL and WL setting to ensure the PHY and controller setting are aligned.

---
 arch/arm/include/asm/arch-aspeed/sdram_ast2600.h | 4 ++++
 drivers/ram/aspeed/sdram_ast2600.c               | 9 +++++++++
 2 files changed, 13 insertions(+)
arch/arm/include/asm/arch-aspeed/sdram_ast2600.h +4 -0
index d2408c0020f8..b0a91ae40d44 100644
@@ -104,6 +104,10 @@
 #define SDRAM_FORCE_PRECHARGE_EN	BIT(4)
 #define SDRAM_REFRESH_EN		BIT(0)
 
+/* MCR14 */
+#define SDRAM_WL_SETTING		GENMASK(23, 20)
+#define SDRAM_CL_SETTING		GENMASK(19, 16)
+
 #define SDRAM_TEST_LEN_SHIFT		4
 #define SDRAM_TEST_LEN_MASK		0xfffff
 #define SDRAM_TEST_START_ADDR_SHIFT	24
drivers/ram/aspeed/sdram_ast2600.c +9 -0
index bda02d062900..5d426088be3e 100644
@@ -15,6 +15,7 @@
 #include <asm/global_data.h>
 #include <linux/err.h>
 #include <linux/kernel.h>
+#include <linux/bitfield.h>
 #include <dt-bindings/clock/ast2600-clock.h>
 
 #define DDR_PHY_TBL_CHG_ADDR            0xaeeddeea
@@ -935,6 +936,7 @@ static void ast2600_sdrammc_lock(struct dram_info *info)
 static void ast2600_sdrammc_common_init(struct ast2600_sdrammc_regs *regs)
 {
 	int i;
+	u32 reg;
 
 	writel(MCR34_MREQI_DIS | MCR34_RESETN_DIS, &regs->power_ctrl);
 	writel(SDRAM_VIDEO_UNLOCK_KEY, &regs->gm_protection_key);
@@ -969,6 +971,13 @@ static void ast2600_sdrammc_common_init(struct ast2600_sdrammc_regs *regs)
 	for (i = 0; i < ARRAY_SIZE(ddr4_ac_timing); ++i)
 		writel(ddr4_ac_timing[i], &regs->ac_timing[i]);
 
+	/* update CL and WL */
+	reg = readl(&regs->ac_timing[1]);
+	reg &= ~(SDRAM_WL_SETTING | SDRAM_CL_SETTING);
+	reg |= FIELD_PREP(SDRAM_WL_SETTING, CONFIG_WL - 5) |
+	       FIELD_PREP(SDRAM_CL_SETTING, CONFIG_RL - 5);
+	writel(reg, &regs->ac_timing[1]);
+
 	writel(DDR4_MR01_MODE, &regs->mr01_mode_setting);
 	writel(DDR4_MR23_MODE, &regs->mr23_mode_setting);
 	writel(DDR4_MR45_MODE, &regs->mr45_mode_setting);
Signature · 1 line
2.25.1
reviewer
#2 lore raw

RE: [PATCH 1/3] ram: ast2600: Fix incorrect statement of the register polling

In reply to Dylan Hung
Quoted 14 lines

-----Original Message-----
From: Dylan Hung <[email protected]>
Sent: Friday, November 11, 2022 3:30 PM
To: Ryan Chen <[email protected]>; ChiaWei Wang <[email protected]>; [email protected]; Dylan Hung <[email protected]>; [email protected]
Cc: BMC-SW <[email protected]>
Subject: [PATCH 1/3] ram: ast2600: Fix incorrect statement of the register polling

The condition "~data" in the if-statement is a typo. The original intention is to poll if SDRAM_PHYCTRL0_INIT bit equals to 0. So use "data == 0" for instead.

Quoted 7 lines

Besides, the bit[1] of "phy_status" register is hardwired to SDRAM_PHYCTRL0_INIT (with inverse logic). Since SDRAM_PHYCTRL0_INIT has already done, remove the unnecessary checking of phy_status[1].

Fixes fde93143469f ("ram: aspeed: Add AST2600 DRAM control support")
Quoted 34 lines
---
 drivers/ram/aspeed/sdram_ast2600.c | 7 +------
 1 file changed, 1 insertion(+), 6 deletions(-)
drivers/ram/aspeed/sdram_ast2600.c +1 -1
index 9ad398d24155..b09232a30413 100644
@@ -449,7 +449,7 @@ static void ast2600_sdramphy_kick_training(struct
 dram_info *info)
 
 	while (1) {
 		data = readl(&regs->phy_ctrl[0]) & SDRAM_PHYCTRL0_INIT;
-		if (~data)
+		if (data == 0)
 			break;
 	}

}

drivers/ram/aspeed/sdram_ast2600.c +0 -5
@@ -984,11 +984,6 @@ static int ast2600_sdrammc_probe(struct udevice
 *dev)
 L_ast2600_sdramphy_train:
 	ast2600_sdrammc_init_ddr4(priv);
 
-	/* make sure DDR-PHY is ready before access */
-	do {
-		reg = readl(priv->phy_status) & BIT(1);
-	} while (reg == 0);
-
 	if (ast2600_sdramphy_check_status(priv) != 0) {
 		printf("DDR4 PHY training fail, retrain\n");

goto L_ast2600_sdramphy_train;
--
2.25.1

reviewer
#5 lore raw

RE: [PATCH 2/3] ram: ast2600: Improve ddr4 timing and signal quality

In reply to Dylan Hung
Quoted 28 lines

-----Original Message-----
From: Dylan Hung <[email protected]>
Sent: Friday, November 11, 2022 3:30 PM
To: Ryan Chen <[email protected]>; ChiaWei Wang <[email protected]>; [email protected]; Dylan Hung <[email protected]>; [email protected]
Cc: BMC-SW <[email protected]>
Subject: [PATCH 2/3] ram: ast2600: Improve ddr4 timing and signal quality

Adjust the following settings to get better timing and signal quality.

1. write DQS/DQ delay
- 1e6e2304[0]
- 1e6e2304[15:8]

2. read DQS/DQ delay
- 0x1e6e0298[0]
- 0x1e6e0298[15:8]

3. CLK/CA timing
- 0x1e6e01a8[31]

4. Read and write termination
- change RTT_ROM from 40 ohm to 48 ohm (MR1[10:8])
- change RTT_PARK from disable to 48 ohm (MR5[8:6])
- change RTT_WR from 120 ohm to disable (MR2[11:9])
- change PHY ODT from 40 ohm to 80 ohm (0x1e6e0130[10:8])

Quoted 8 lines

Note1: Both DDR-PHY and DDR controller have their own registers for DDR4 Mode Registers (MR0~MR6). This patch introduces macros to synchronize the MR value on both sides.

Note2: the waveform meansurement can be found in item #21 of Aspeed AST26x0 Application note (AP note).

Quoted 276 lines
---
 drivers/ram/aspeed/sdram_ast2600.c | 163 ++++++++++++++++++++++++-----
 1 file changed, 138 insertions(+), 25 deletions(-)
drivers/ram/aspeed/sdram_ast2600.c +113 -0
index b09232a30413..bda02d062900 100644
@@ -20,6 +20,119 @@
 #define DDR_PHY_TBL_CHG_ADDR            0xaeeddeea
 #define DDR_PHY_TBL_END                 0xaeededed
 
+/**
+ * phyr030[18:16] - Ron PU (PHY side)
+ * phyr030[14:12] - Ron PD (PHY side)
+ *   b'000 : disable
+ *   b'001 : 240 ohm
+ *   b'010 : 120 ohm
+ *   b'011 : 80 ohm
+ *   b'100 : 60 ohm
+ *   b'101 : 48 ohm
+ *   b'110 : 40 ohm
+ *   b'111 : 34 ohm (default)
+ */
+#define PHY_RON				((0x7 << 16) | (0x7 << 12))
+
+/**
+ * phyr030[10:8] - ODT configuration (PHY side)
+ *   b'000 : ODT disabled
+ *   b'001 : 240 ohm
+ *   b'010 : 120 ohm
+ *   b'011 : 80 ohm (default)
+ *   b'100 : 60 ohm
+ *   b'101 : 48 ohm
+ *   b'110 : 40 ohm
+ *   b'111 : 34 ohm
+ */
+#define PHY_ODT				(0x3 << 8)
+
+/**
+ * MR1[2:1] output driver impedance
+ *   b'00 : 34 ohm (default)
+ *   b'01 : 48 ohm
+ */
+#define DRAM_RON			(0x0 << 1)
+
+/**
+ * DRAM ODT - synchronous ODT mode
+ *   RTT_WR: disable
+ *   RTT_NOM = RTT_PARK
+ *
+ * MR1[10:8] RTT_NOM
+ *   b'000 : RTT_NOM disable
+ *   b'001 : 60 ohm
+ *   b'010 : 120 ohm
+ *   b'011 : 40 ohm
+ *   b'100 : 240 ohm
+ *   b'101 : 48 ohm  (default)
+ *   b'110 : 80 ohm
+ *   b'111 : 34 ohm
+ *
+ * MR5[8:6] RTT_PARK
+ *   b'000 : RTT_PARK disable
+ *   b'001 : 60 ohm
+ *   b'010 : 120 ohm
+ *   b'011 : 40 ohm
+ *   b'100 : 240 ohm
+ *   b'101 : 48 ohm  (default)
+ *   b'110 : 80 ohm
+ *   b'111 : 34 ohm
+ *
+ * MR2[11:9] RTT_WR
+ *   b'000 : Dynamic ODT off  (default)
+ *   b'001 : 120 ohm
+ *   b'010 : 240 ohm
+ *   b'011 : Hi-Z
+ *   b'100 : 80 ohm
+ */
+#define RTT_WR				(0x0 << 9)
+#define RTT_NOM				(0x5 << 8)
+#define RTT_PARK			(0x5 << 6)
+
+/**
+ * MR6[6] VrefDQ training range
+ *   b'0 : range 1
+ *   b'1 : range 2 (default)
+ */
+#define VREFDQ_RANGE_2			BIT(6)
+
+/**
+ * Latency setting:
+ * AL = PL = 0 (hardware fixed setting)
+ * -> WL = AL + CWL + PL = CWL
+ * -> RL = AL + CL + PL = CL
+ */
+#define CONFIG_WL			9
+#define CONFIG_RL			12
+#define T_RDDATA_EN			((CONFIG_RL - 2) << 8)
+#define T_PHY_WRLAT			(CONFIG_WL - 2)
+
+/* MR0 */
+#define MR0_CL_12			(BIT(4) | BIT(2))
+#define MR0_WR12_RTP6			BIT(9)
+#define MR0_DLL_RESET			BIT(8)
+#define MR0_VAL				(MR0_CL_12 | MR0_WR12_RTP6 |
 MR0_DLL_RESET)
+
+/* MR1 */
+#define MR1_VAL				(0x0001 | RTT_NOM | DRAM_RON)
+
+/* MR2 */
+#define MR2_CWL_9			0
+#define MR2_VAL				(0x0000 | RTT_WR | MR2_CWL_9)
+
+/* MR3 ~ MR6 */
+#define MR3_VAL				0x0000
+#define MR4_VAL				0x0000
+#define MR5_VAL				(0x0400 | RTT_PARK)
+#define MR6_VAL				0x0400
+
+/**
+ * The offset value applied to the DDR PHY write data eye training
+result
+ * to fine-tune the write DQ/DQS alignment  */
+#define WR_DATA_EYE_OFFSET		(0x10 << 8)
+
 #if defined(CONFIG_ASPEED_DDR4_800)
 u32 ast2600_sdramphy_config[165] = {
drivers/ram/aspeed/sdram_ast2600.c +25 -26
 	0x1e6e0100,	// start address
@@ -35,7 +148,7 @@ u32 ast2600_sdramphy_config[165] = {
 	0x20000000,	// phyr024
 	0x00000008,	// phyr028
 	0x00000000,	// phyr02c
-	0x00077600,	// phyr030
+	(PHY_RON | PHY_ODT),	/* phyr030 */
 	0x00000000,	// phyr034
 	0x00000000,	// phyr038
 	0x20000000,	// phyr03c
@@ -44,18 +157,18 @@ u32 ast2600_sdramphy_config[165] = {
 	0x00002f07,	// phyr048
 	0x00003080,	// phyr04c
 	0x04000000,	// phyr050
-	0x00000200,	// phyr054
-	0x03140201,	// phyr058
-	0x04800000,	// phyr05c
-	0x0800044e,	// phyr060
+	((MR3_VAL << 16) | MR2_VAL),	/* phyr054 */
+	((MR0_VAL << 16) | MR1_VAL),	/* phyr058 */
+	((MR5_VAL << 16) | MR4_VAL),	/* phyr05c */
+	((0x0800 << 16) | MR6_VAL | VREFDQ_RANGE_2 | 0xe), /* phyr060 */
 	0x00000000,	// phyr064
 	0x00180008,	// phyr068
 	0x00e00400,	// phyr06c
 	0x00140206,	// phyr070
 	0x1d4c0000,	// phyr074
-	0x493e0107,	// phyr078
+	(0x493e0100 | T_PHY_WRLAT),	/* phyr078 */
 	0x08060404,	// phyr07c
-	0x90000a00,	// phyr080
+	(0x90000000 | T_RDDATA_EN),	/* phyr080 */
 	0x06420618,	// phyr084
 	0x00001002,	// phyr088
 	0x05701016,	// phyr08c
@@ -94,7 +207,7 @@ u32 ast2600_sdramphy_config[165] = {
 	0x20202020,	// phyr09c
 	0x20202020,	// phyr0a0
 	0x00002020,	// phyr0a4
-	0x80000000,	// phyr0a8
+	0x00000000,	/* phyr0a8 */
 	0x00000001,	// phyr0ac
 	0xaeeddeea,	// change address
 	0x1e6e0318,	// new address
@@ -154,7 +267,7 @@ u32 ast2600_sdramphy_config[165] = {
 	0x20202020,	// phyr170
 	0xaeeddeea,	// change address
 	0x1e6e0298,	// new address
-	0x20200800,	// phyr198
+	0x20200000,	/* phyr198 */
 	0x20202020,	// phyr19c
 	0x20202020,	// phyr1a0
 	0x20202020,	// phyr1a4
@@ -177,7 +290,7 @@ u32 ast2600_sdramphy_config[165] = {
 	0x00002020,	// phyr1e8
 	0xaeeddeea,	// change address
 	0x1e6e0304,	// new address
-	0x00000800,	// phyr204
+	(0x00000001 | WR_DATA_EYE_OFFSET), /* phyr204 */
 	0xaeeddeea,	// change address
 	0x1e6e027c,	// new address
 	0x4e400000,	// phyr17c
@@ -203,7 +316,7 @@ u32 ast2600_sdramphy_config[165] = {
 	0x20000000,	// phyr024
 	0x00000008,	// phyr028
 	0x00000000,	// phyr02c
-	0x00077600,	// phyr030
+	(PHY_RON | PHY_ODT),	/* phyr030 */
 	0x00000000,	// phyr034
 	0x00000000,	// phyr038
 	0x20000000,	// phyr03c
@@ -212,18 +325,18 @@ u32 ast2600_sdramphy_config[165] = {
 	0x00002f07,	// phyr048
 	0x00003080,	// phyr04c
 	0x04000000,	// phyr050
-	0x00000200,	// phyr054
-	0x03140501,	// phyr058-rtt:40
-	0x04800000,	// phyr05c
-	0x0800044e,	// phyr060
+	((MR3_VAL << 16) | MR2_VAL),	/* phyr054 */
+	((MR0_VAL << 16) | MR1_VAL),	/* phyr058 */
+	((MR5_VAL << 16) | MR4_VAL),	/* phyr05c */
+	((0x0800 << 16) | MR6_VAL | VREFDQ_RANGE_2 | 0xe), /* phyr060 */
 	0x00000000,	// phyr064
 	0x00180008,	// phyr068
 	0x00e00400,	// phyr06c
 	0x00140206,	// phyr070
 	0x1d4c0000,	// phyr074
-	0x493e0107,	// phyr078
+	(0x493e0100 | T_PHY_WRLAT),	/* phyr078 */
 	0x08060404,	// phyr07c
-	0x90000a00,	// phyr080
+	(0x90000000 | T_RDDATA_EN),	/* phyr080 */
 	0x06420c30,	// phyr084
 	0x00001002,	// phyr088
 	0x05701016,	// phyr08c
@@ -256,13 +369,13 @@ u32 ast2600_sdramphy_config[165] = {
 	0x00000000,	// phyr200
 	0xaeeddeea,	// change address
 	0x1e6e0194,	// new address
-	0x801112e0,	// phyr094 - bit12=1,15=0,- write window is ok
+	0x801112e0,	// phyr094
 	0xaeeddeea,	// change address
 	0x1e6e019c,	// new address
 	0x20202020,	// phyr09c
 	0x20202020,	// phyr0a0
 	0x00002020,	// phyr0a4
-	0x80000000,	// phyr0a8
+	0x00000000,	/* phyr0a8 */
 	0x00000001,	// phyr0ac
 	0xaeeddeea,	// change address
 	0x1e6e0318,	// new address
@@ -322,7 +435,7 @@ u32 ast2600_sdramphy_config[165] = {
 	0x20202020,	// phyr170
 	0xaeeddeea,	// change address
 	0x1e6e0298,	// new address
-	0x20200800,	// phyr198
+	0x20200000,	/* phyr198 */
 	0x20202020,	// phyr19c
 	0x20202020,	// phyr1a0
 	0x20202020,	// phyr1a4
@@ -345,7 +458,7 @@ u32 ast2600_sdramphy_config[165] = {
 	0x00002020,	// phyr1e8
 	0xaeeddeea,	// change address
 	0x1e6e0304,	// new address
-	0x00000800,	// phyr204
+	(0x00000001 | WR_DATA_EYE_OFFSET), /* phyr204 */
 	0xaeeddeea,	// change address
 	0x1e6e027c,	// new address
 	0x4e400000,	// phyr17c
@@ -388,10 +501,10 @@ u32 ast2600_sdramphy_config[165] = {
  * AC timing and SDRAM mode register setting
  * for real chip are derived from the model GDDR4-1600
  */
-#define DDR4_MR01_MODE	0x03010510
-#define DDR4_MR23_MODE	0x00000000
-#define DDR4_MR45_MODE	0x04000000
-#define DDR4_MR6_MODE	0x00000400
+#define DDR4_MR01_MODE	((MR1_VAL << 16) | MR0_VAL)
+#define DDR4_MR23_MODE	((MR3_VAL << 16) | MR2_VAL)
+#define DDR4_MR45_MODE	((MR5_VAL << 16) | MR4_VAL)
+#define DDR4_MR6_MODE	MR6_VAL
 #define DDR4_TRFC_1600	0x467299f1
 #define DDR4_TRFC_1333	0x3a5f80c9
 #define DDR4_TRFC_800	0x23394c78
--

2.25.1

reviewer
#8 lore raw

RE: [PATCH 3/3] ram: ast2600: Align the RL and WL setting

In reply to Dylan Hung
Quoted 9 lines

-----Original Message-----
From: Dylan Hung <[email protected]>
Sent: Friday, November 11, 2022 3:30 PM
To: Ryan Chen <[email protected]>; ChiaWei Wang <[email protected]>; [email protected]; Dylan Hung <[email protected]>; [email protected]
Cc: BMC-SW <[email protected]>
Subject: [PATCH 3/3] ram: ast2600: Align the RL and WL setting

Quoted 4 lines

Use macro to represent the RL and WL setting to ensure the PHY and controller setting are aligned.

Quoted 59 lines
---
 arch/arm/include/asm/arch-aspeed/sdram_ast2600.h | 4 ++++
 drivers/ram/aspeed/sdram_ast2600.c               | 9 +++++++++
 2 files changed, 13 insertions(+)
arch/arm/include/asm/arch-aspeed/sdram_ast2600.h +4 -0
index d2408c0020f8..b0a91ae40d44 100644
@@ -104,6 +104,10 @@
 #define SDRAM_FORCE_PRECHARGE_EN	BIT(4)
 #define SDRAM_REFRESH_EN		BIT(0)
 
+/* MCR14 */
+#define SDRAM_WL_SETTING		GENMASK(23, 20)
+#define SDRAM_CL_SETTING		GENMASK(19, 16)
+
 #define SDRAM_TEST_LEN_SHIFT		4
 #define SDRAM_TEST_LEN_MASK		0xfffff
 #define SDRAM_TEST_START_ADDR_SHIFT	24
drivers/ram/aspeed/sdram_ast2600.c +2 -1
index bda02d062900..5d426088be3e 100644
@@ -15,6 +15,7 @@
 #include <asm/global_data.h>
 #include <linux/err.h>
 #include <linux/kernel.h>
+#include <linux/bitfield.h>
 #include <dt-bindings/clock/ast2600-clock.h>
 
 #define DDR_PHY_TBL_CHG_ADDR            0xaeeddeea
@@ -935,6 +936,7 @@ static void ast2600_sdrammc_lock(struct dram_info
 *info)  static void ast2600_sdrammc_common_init(struct
 ast2600_sdrammc_regs *regs)  {
 	int i;
+	u32 reg;
 
 	writel(MCR34_MREQI_DIS | MCR34_RESETN_DIS, &regs->power_ctrl);
 	writel(SDRAM_VIDEO_UNLOCK_KEY, &regs->gm_protection_key); @@
-969,6 +971,13 @@ static void ast2600_sdrammc_common_init(struct

ast2600_sdrammc_regs *regs)

drivers/ram/aspeed/sdram_ast2600.c +7 -1
 	for (i = 0; i < ARRAY_SIZE(ddr4_ac_timing); ++i)
 		writel(ddr4_ac_timing[i], &regs->ac_timing[i]);
 
+	/* update CL and WL */
+	reg = readl(&regs->ac_timing[1]);
+	reg &= ~(SDRAM_WL_SETTING | SDRAM_CL_SETTING);
+	reg |= FIELD_PREP(SDRAM_WL_SETTING, CONFIG_WL - 5) |
+	       FIELD_PREP(SDRAM_CL_SETTING, CONFIG_RL - 5);
+	writel(reg, &regs->ac_timing[1]);
+
 	writel(DDR4_MR01_MODE, &regs->mr01_mode_setting);
 	writel(DDR4_MR23_MODE, &regs->mr23_mode_setting);
 	writel(DDR4_MR45_MODE, &regs->mr45_mode_setting);
--

2.25.1

#3 lore raw

Re: [PATCH 1/3] ram: ast2600: Fix incorrect statement of the register polling

In reply to Dylan Hung
Quoted 11 lines · Dylan Hung

The condition "~data" in the if-statement is a typo. The original intention is to poll if SDRAM_PHYCTRL0_INIT bit equals to 0. So use "data == 0" for instead.

Besides, the bit[1] of "phy_status" register is hardwired to SDRAM_PHYCTRL0_INIT (with inverse logic). Since SDRAM_PHYCTRL0_INIT has already done, remove the unnecessary checking of phy_status[1].

Fixes fde93143469f ("ram: aspeed: Add AST2600 DRAM control support")

Applied to u-boot/master, thanks!

Signature · 1 line
Tom
#6 lore raw

Re: [PATCH 2/3] ram: ast2600: Improve ddr4 timing and signal quality

In reply to Dylan Hung
Quoted 19 lines · Dylan Hung

Adjust the following settings to get better timing and signal quality.

1. write DQS/DQ delay
- 1e6e2304[0]
- 1e6e2304[15:8]

2. read DQS/DQ delay
- 0x1e6e0298[0]
- 0x1e6e0298[15:8]

3. CLK/CA timing
- 0x1e6e01a8[31]

4. Read and write termination
- change RTT_ROM from 40 ohm to 48 ohm (MR1[10:8])
- change RTT_PARK from disable to 48 ohm (MR5[8:6])
- change RTT_WR from 120 ohm to disable (MR2[11:9])
- change PHY ODT from 40 ohm to 80 ohm (0x1e6e0130[10:8])

Quoted 8 lines

Note1: Both DDR-PHY and DDR controller have their own registers for DDR4 Mode Registers (MR0~MR6). This patch introduces macros to synchronize the MR value on both sides.

Note2: the waveform meansurement can be found in item #21 of Aspeed AST26x0 Application note (AP note).

Applied to u-boot/master, thanks!

Signature · 1 line
Tom
#9 lore raw

Re: [PATCH 3/3] ram: ast2600: Align the RL and WL setting

In reply to Dylan Hung
Quoted 4 lines · Dylan Hung

Use macro to represent the RL and WL setting to ensure the PHY and controller setting are aligned.

Applied to u-boot/master, thanks!

Signature · 1 line
Tom