Skip to contentSkip to conversation

rtl8221b/8251b add C45 instances and SerDes switching

PATCH Superseded Eric Woudstra 4 participants 15 messages Mar 3, 2024 – Mar 5, 2024

Subsystems (4)

v2 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

v2 cover rtl8221b/8251b add C45 instances and SerDes switching

Based on the comments in [PATCH net-next]
"Realtek RTL822x PHY rework to c45 and SerDes interface switching"

Adds SerDes switching interface between 2500base-x and sgmii for rtl822x and rtl8251b.

Add get_rate_matching() for rtl822x and rtl8251b, reading the serdes mode from phy.

Driver instances are added for rtl8221b and rtl8251b for Clause 45 access only. The existing code is not touched, they use newly added functions. They also use the same rtl822x_config_init() and rtl822x_get_rate_matching() as these functions also can be used for direct Clause 45 access. Also Adds definition of MMC 31 registers, which cannot be used through C45-over-C22, only when phydev->is_c45 is set.

Change rtlgen_get_speed() so the register value is passed as argument. Using Clause 45 access, this value is retrieved differently. Rename it to rtlgen_decode_speed() and add a call to it in rtl822x_c45_read_status().

Add rtl822x_c45_get_features() to set supported ports.

Then 2 quirks are added for sfp modules known to have a rtl8221b behind RollBall, Clause 45 only, protocol.

Changed in PATCH v2:

* Set author to Marek for the commit of the new C45 instances
* Separate commit for setting supported ports
* Renamed rtlgen_get_speed to rtlgen_decode_speed
* Always fill in possible interfaces
* Renamed sfp_fixup_oem_2_5g to sfp_fixup_oem_2_5gbaset
* Only update phydev->interface when link is up

Alexander Couzens (1):
net: phy: realtek: configure SerDes mode for rtl822x/8251b PHYs

Eric Woudstra (4):
net: phy: realtek: add get_rate_matching() for rtl822x/8251b PHYs
net: phy: realtek: Change rtlgen_get_speed() to rtlgen_decode_speed()
net: phy: realtek: add rtl822x_c45_get_features() to set supported
ports
net: sfp: Fixup for OEM SFP-2.5G-T module

Marek Behún (2):
net: phy: realtek: Add driver instances for rtl8221b/8251b via Clause

    45

net: sfp: add quirk for another multigig RollBall transceiver

 drivers/net/phy/realtek.c | 325 +++++++++++++++++++++++++++++++++++---
 drivers/net/phy/sfp.c     |  10 +-
 2 files changed, 312 insertions(+), 23 deletions(-)
Signature · 1 line
2.42.1
#1 lore raw

PATCH v2 1/7 net: phy: realtek: configure SerDes mode for rtl822x/8251b PHYs

From: Alexander Couzens <[email protected]>

The rtl822x series and rtl8251b support switching SerDes mode between 2500base-x and sgmii based on the negotiated copper speed.

Configure this switching mode according to SerDes modes supported by host.

There is an additional datasheet for RTL8226B/RTL8221B called "SERDES MODE SETTING FLOW APPLICATION NOTE" where this sequence to setup interface and rate adapter mode.

However, there is no documentation about the meaning of registers and bits, it's literally just magic numbers and pseudo-code.

[ refactored, dropped HiSGMII mode and changed commit message ]
[ changed rtl822x_update_interface() to use vendor register ]
[ always fill in possible interfaces ]
---
 drivers/net/phy/realtek.c | 99 ++++++++++++++++++++++++++++++++++++++-
 1 file changed, 97 insertions(+), 2 deletions(-)
drivers/net/phy/realtek.c +97 -2
index 1fa70427b2a2..8a876e003774 100644
@@ -54,6 +54,16 @@
 						 RTL8201F_ISR_LINK)
 #define RTL8201F_IER				0x13
 
+#define RTL822X_VND1_SERDES_OPTION			0x697a
+#define RTL822X_VND1_SERDES_OPTION_MODE_MASK		GENMASK(5, 0)
+#define RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX_SGMII		0
+#define RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX		2
+
+#define RTL822X_VND1_SERDES_CTRL3			0x7580
+#define RTL822X_VND1_SERDES_CTRL3_MODE_MASK		GENMASK(5, 0)
+#define RTL822X_VND1_SERDES_CTRL3_MODE_SGMII			0x02
+#define RTL822X_VND1_SERDES_CTRL3_MODE_2500BASEX		0x16
+
 #define RTL8366RB_POWER_SAVE			0x15
 #define RTL8366RB_POWER_SAVE_ON			BIT(12)
 
@@ -659,6 +669,60 @@ static int rtl822x_write_mmd(struct phy_device *phydev, int devnum, u16 regnum,
 	return ret;
 }
 
+static int rtl822x_config_init(struct phy_device *phydev)
+{
+	bool has_2500, has_sgmii;
+	u16 mode;
+	int ret;
+
+	has_2500 = test_bit(PHY_INTERFACE_MODE_2500BASEX,
+			    phydev->host_interfaces) ||
+		   phydev->interface == PHY_INTERFACE_MODE_2500BASEX;
+
+	has_sgmii = test_bit(PHY_INTERFACE_MODE_SGMII,
+			     phydev->host_interfaces) ||
+		    phydev->interface == PHY_INTERFACE_MODE_SGMII;
+
+	/* fill in possible interfaces */
+	__assign_bit(PHY_INTERFACE_MODE_2500BASEX, phydev->possible_interfaces,
+		     has_2500);
+	__assign_bit(PHY_INTERFACE_MODE_SGMII, phydev->possible_interfaces,
+		     has_sgmii);
+
+	if (!has_2500 && !has_sgmii)
+		return 0;
+
+	/* determine SerDes option mode */
+	if (has_2500 && !has_sgmii)
+		mode = RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX;
+	else
+		mode = RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX_SGMII;
+
+	/* the following sequence with magic numbers sets up the SerDes
+	 * option mode
+	 */
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x75f3, 0);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_modify_mmd_changed(phydev, MDIO_MMD_VEND1,
+				     RTL822X_VND1_SERDES_OPTION,
+				     RTL822X_VND1_SERDES_OPTION_MODE_MASK,
+				     mode);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x6a04, 0x0503);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x6f10, 0xd455);
+	if (ret < 0)
+		return ret;
+
+	return phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x6f11, 0x8020);
+}
+
 static int rtl822x_get_features(struct phy_device *phydev)
 {
 	int val;
@@ -695,6 +759,28 @@ static int rtl822x_config_aneg(struct phy_device *phydev)
 	return __genphy_config_aneg(phydev, ret);
 }
 
+static void rtl822x_update_interface(struct phy_device *phydev)
+{
+	int val;
+
+	if (!phydev->link)
+		return;
+
+	/* Change interface according to serdes mode */
+	val = phy_read_mmd(phydev, MDIO_MMD_VEND1, RTL822X_VND1_SERDES_CTRL3);
+	if (val < 0)
+		return;
+
+	switch (val & RTL822X_VND1_SERDES_CTRL3_MODE_MASK) {
+	case RTL822X_VND1_SERDES_CTRL3_MODE_2500BASEX:
+		phydev->interface = PHY_INTERFACE_MODE_2500BASEX;
+		break;
+	case RTL822X_VND1_SERDES_CTRL3_MODE_SGMII:
+		phydev->interface = PHY_INTERFACE_MODE_SGMII;
+		break;
+	}
+}
+
 static int rtl822x_read_status(struct phy_device *phydev)
 {
 	int ret;
@@ -709,11 +795,13 @@ static int rtl822x_read_status(struct phy_device *phydev)
 						  lpadv);
 	}
 
-	ret = genphy_read_status(phydev);
+	ret = rtlgen_read_status(phydev);
 	if (ret < 0)
 		return ret;
 
-	return rtlgen_get_speed(phydev);
+	rtl822x_update_interface(phydev);
+
+	return 0;
 }
 
 static bool rtlgen_supports_2_5gbps(struct phy_device *phydev)
@@ -976,6 +1064,7 @@ static struct phy_driver realtek_drvs[] = {
 		.match_phy_device = rtl8226_match_phy_device,
 		.get_features	= rtl822x_get_features,
 		.config_aneg	= rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status	= rtl822x_read_status,
 		.suspend	= genphy_suspend,
 		.resume		= rtlgen_resume,
@@ -988,6 +1077,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name		= "RTL8226B_RTL8221B 2.5Gbps PHY",
 		.get_features	= rtl822x_get_features,
 		.config_aneg	= rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status	= rtl822x_read_status,
 		.suspend	= genphy_suspend,
 		.resume		= rtlgen_resume,
@@ -1000,6 +1090,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8226-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
@@ -1010,6 +1101,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8226B-CG_RTL8221B-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
@@ -1019,6 +1111,7 @@ static struct phy_driver realtek_drvs[] = {
 		PHY_ID_MATCH_EXACT(0x001cc849),
 		.name           = "RTL8221B-VB-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
+		.config_init    = rtl822x_config_init,
 		.config_aneg    = rtl822x_config_aneg,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
@@ -1030,6 +1123,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8221B-VM-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
@@ -1040,6 +1134,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8251B 5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
Signature · 1 line
2.42.1
#9 lore raw

PATCH v2 2/7 net: phy: realtek: add get_rate_matching() for rtl822x/8251b PHYs

In reply to Eric Woudstra

Uses vendor register to determine if SerDes is setup in rate-matching mode.

Rate-matching only supported when SerDes is set to 2500base-x.

---
 drivers/net/phy/realtek.c | 29 +++++++++++++++++++++++++++++
 1 file changed, 29 insertions(+)
drivers/net/phy/realtek.c +29 -0
index 8a876e003774..d7a47edd529e 100644
@@ -723,6 +723,28 @@ static int rtl822x_config_init(struct phy_device *phydev)
 	return phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x6f11, 0x8020);
 }
 
+static int rtl822x_get_rate_matching(struct phy_device *phydev,
+				     phy_interface_t iface)
+{
+	int val;
+
+	/* Only rate matching at 2500base-x */
+	if (iface != PHY_INTERFACE_MODE_2500BASEX)
+		return RATE_MATCH_NONE;
+
+	val = phy_read_mmd(phydev, MDIO_MMD_VEND1, RTL822X_VND1_SERDES_OPTION);
+	if (val < 0)
+		return val;
+
+	switch (val & RTL822X_VND1_SERDES_OPTION_MODE_MASK) {
+	case RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX:
+		return RATE_MATCH_PAUSE;
+	/* case RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX_SGMII: */
+	default:
+		return RATE_MATCH_NONE;
+	}
+}
+
 static int rtl822x_get_features(struct phy_device *phydev)
 {
 	int val;
@@ -1065,6 +1087,7 @@ static struct phy_driver realtek_drvs[] = {
 		.get_features	= rtl822x_get_features,
 		.config_aneg	= rtl822x_config_aneg,
 		.config_init    = rtl822x_config_init,
+		.get_rate_matching = rtl822x_get_rate_matching,
 		.read_status	= rtl822x_read_status,
 		.suspend	= genphy_suspend,
 		.resume		= rtlgen_resume,
@@ -1078,6 +1101,7 @@ static struct phy_driver realtek_drvs[] = {
 		.get_features	= rtl822x_get_features,
 		.config_aneg	= rtl822x_config_aneg,
 		.config_init    = rtl822x_config_init,
+		.get_rate_matching = rtl822x_get_rate_matching,
 		.read_status	= rtl822x_read_status,
 		.suspend	= genphy_suspend,
 		.resume		= rtlgen_resume,
@@ -1091,6 +1115,7 @@ static struct phy_driver realtek_drvs[] = {
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
 		.config_init    = rtl822x_config_init,
+		.get_rate_matching = rtl822x_get_rate_matching,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
@@ -1102,6 +1127,7 @@ static struct phy_driver realtek_drvs[] = {
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
 		.config_init    = rtl822x_config_init,
+		.get_rate_matching = rtl822x_get_rate_matching,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
@@ -1112,6 +1138,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8221B-VB-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_init    = rtl822x_config_init,
+		.get_rate_matching = rtl822x_get_rate_matching,
 		.config_aneg    = rtl822x_config_aneg,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
@@ -1124,6 +1151,7 @@ static struct phy_driver realtek_drvs[] = {
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
 		.config_init    = rtl822x_config_init,
+		.get_rate_matching = rtl822x_get_rate_matching,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
@@ -1135,6 +1163,7 @@ static struct phy_driver realtek_drvs[] = {
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
 		.config_init    = rtl822x_config_init,
+		.get_rate_matching = rtl822x_get_rate_matching,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
Signature · 1 line
2.42.1
#10 lore raw

PATCH v2 3/7 net: phy: realtek: Add driver instances for rtl8221b/8251b via Clause 45

In reply to Eric Woudstra

From: Marek Behún <[email protected]>

Collected from several commits in [PATCH net-next] "Realtek RTL822x PHY rework to c45 and SerDes interface switching"

The instances are used by Clause 45 only accessible PHY's on several sfp modules, which are using RollBall protocol.

[ Added matching functions to differentiate C45 instances ]
---
 drivers/net/phy/realtek.c | 146 ++++++++++++++++++++++++++++++++++++--
 1 file changed, 140 insertions(+), 6 deletions(-)
drivers/net/phy/realtek.c +140 -6
index d7a47edd529e..f9a67761878e 100644
@@ -64,6 +64,13 @@
 #define RTL822X_VND1_SERDES_CTRL3_MODE_SGMII			0x02
 #define RTL822X_VND1_SERDES_CTRL3_MODE_2500BASEX		0x16
 
+/* RTL822X_VND2_XXXXX registers are only accessible when phydev->is_c45
+ * is set, they cannot be accessed by C45-over-C22.
+ */
+#define RTL822X_VND2_GBCR				0xa412
+
+#define RTL822X_VND2_GANLPAR				0xa414
+
 #define RTL8366RB_POWER_SAVE			0x15
 #define RTL8366RB_POWER_SAVE_ON			BIT(12)
 
@@ -74,6 +81,9 @@
 
 #define RTL_GENERIC_PHYID			0x001cc800
 #define RTL_8211FVD_PHYID			0x001cc878
+#define RTL_8221B_VB_CG				0x001cc849
+#define RTL_8221B_VN_CG				0x001cc84a
+#define RTL_8251B				0x001cc862
 
 MODULE_DESCRIPTION("Realtek PHY driver");
 MODULE_AUTHOR("Johnson Leung");
@@ -826,6 +836,56 @@ static int rtl822x_read_status(struct phy_device *phydev)
 	return 0;
 }
 
+static int rtl822x_c45_config_aneg(struct phy_device *phydev)
+{
+	bool changed = false;
+	int ret, val;
+
+	if (phydev->autoneg == AUTONEG_DISABLE)
+		return genphy_c45_pma_setup_forced(phydev);
+
+	ret = genphy_c45_an_config_aneg(phydev);
+	if (ret < 0)
+		return ret;
+	if (ret > 0)
+		changed = true;
+
+	val = linkmode_adv_to_mii_ctrl1000_t(phydev->advertising);
+
+	/* Vendor register as C45 has no standardized support for 1000BaseT */
+	ret = phy_modify_mmd_changed(phydev, MDIO_MMD_VEND2, RTL822X_VND2_GBCR,
+				     ADVERTISE_1000FULL, val);
+	if (ret < 0)
+		return ret;
+	if (ret > 0)
+		changed = true;
+
+	return genphy_c45_check_and_restart_aneg(phydev, changed);
+}
+
+static int rtl822x_c45_read_status(struct phy_device *phydev)
+{
+	int ret, val;
+
+	ret = genphy_c45_read_status(phydev);
+	if (ret < 0)
+		return ret;
+
+	/* Vendor register as C45 has no standardized support for 1000BaseT */
+	if (phydev->autoneg == AUTONEG_ENABLE) {
+		val = phy_read_mmd(phydev, MDIO_MMD_VEND2,
+				   RTL822X_VND2_GANLPAR);
+		if (val < 0)
+			return val;
+
+		mii_stat1000_mod_linkmode_lpa_t(phydev->lp_advertising, val);
+	}
+
+	rtl822x_update_interface(phydev);
+
+	return 0;
+}
+
 static bool rtlgen_supports_2_5gbps(struct phy_device *phydev)
 {
 	int val;
@@ -849,6 +909,44 @@ static int rtl8226_match_phy_device(struct phy_device *phydev)
 	       rtlgen_supports_2_5gbps(phydev);
 }
 
+static int rtlgen_is_c45_match(struct phy_device *phydev, unsigned int id, bool is_c45)
+{
+	if (phydev->is_c45)
+		return is_c45 && (id == phydev->c45_ids.device_ids[1]);
+	else
+		return !is_c45 && (id == phydev->phy_id);
+}
+
+static int rtl8221b_vb_cg_c22_match_phy_device(struct phy_device *phydev)
+{
+	return rtlgen_is_c45_match(phydev, RTL_8221B_VB_CG, false);
+}
+
+static int rtl8221b_vb_cg_c45_match_phy_device(struct phy_device *phydev)
+{
+	return rtlgen_is_c45_match(phydev, RTL_8221B_VB_CG, true);
+}
+
+static int rtl8221b_vn_cg_c22_match_phy_device(struct phy_device *phydev)
+{
+	return rtlgen_is_c45_match(phydev, RTL_8221B_VN_CG, false);
+}
+
+static int rtl8221b_vn_cg_c45_match_phy_device(struct phy_device *phydev)
+{
+	return rtlgen_is_c45_match(phydev, RTL_8221B_VN_CG, true);
+}
+
+static int rtl8251b_c22_match_phy_device(struct phy_device *phydev)
+{
+	return rtlgen_is_c45_match(phydev, RTL_8251B, false);
+}
+
+static int rtl8251b_c45_match_phy_device(struct phy_device *phydev)
+{
+	return rtlgen_is_c45_match(phydev, RTL_8251B, true);
+}
+
 static int rtlgen_resume(struct phy_device *phydev)
 {
 	int ret = genphy_resume(phydev);
@@ -859,6 +957,15 @@ static int rtlgen_resume(struct phy_device *phydev)
 	return ret;
 }
 
+static int rtlgen_c45_resume(struct phy_device *phydev)
+{
+	int ret = genphy_c45_pma_resume(phydev);
+
+	msleep(20);
+
+	return ret;
+}
+
 static int rtl9000a_config_init(struct phy_device *phydev)
 {
 	phydev->autoneg = AUTONEG_DISABLE;
@@ -1134,8 +1241,8 @@ static struct phy_driver realtek_drvs[] = {
 		.read_page      = rtl821x_read_page,
 		.write_page     = rtl821x_write_page,
 	}, {
-		PHY_ID_MATCH_EXACT(0x001cc849),
-		.name           = "RTL8221B-VB-CG 2.5Gbps PHY",
+		.match_phy_device = rtl8221b_vb_cg_c22_match_phy_device,
+		.name           = "RTL8221B-VB-CG 2.5Gbps PHY (C22)",
 		.get_features   = rtl822x_get_features,
 		.config_init    = rtl822x_config_init,
 		.get_rate_matching = rtl822x_get_rate_matching,
@@ -1146,8 +1253,17 @@ static struct phy_driver realtek_drvs[] = {
 		.read_page      = rtl821x_read_page,
 		.write_page     = rtl821x_write_page,
 	}, {
-		PHY_ID_MATCH_EXACT(0x001cc84a),
-		.name           = "RTL8221B-VM-CG 2.5Gbps PHY",
+		.match_phy_device = rtl8221b_vb_cg_c45_match_phy_device,
+		.name           = "RTL8221B-VB-CG 2.5Gbps PHY (C45)",
+		.config_init    = rtl822x_config_init,
+		.get_rate_matching = rtl822x_get_rate_matching,
+		.config_aneg    = rtl822x_c45_config_aneg,
+		.read_status    = rtl822x_c45_read_status,
+		.suspend        = genphy_c45_pma_suspend,
+		.resume         = rtlgen_c45_resume,
+	}, {
+		.match_phy_device = rtl8221b_vn_cg_c22_match_phy_device,
+		.name           = "RTL8221B-VM-CG 2.5Gbps PHY (C22)",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
 		.config_init    = rtl822x_config_init,
@@ -1158,8 +1274,17 @@ static struct phy_driver realtek_drvs[] = {
 		.read_page      = rtl821x_read_page,
 		.write_page     = rtl821x_write_page,
 	}, {
-		PHY_ID_MATCH_EXACT(0x001cc862),
-		.name           = "RTL8251B 5Gbps PHY",
+		.match_phy_device = rtl8221b_vn_cg_c45_match_phy_device,
+		.name           = "RTL8221B-VN-CG 2.5Gbps PHY (C45)",
+		.config_init    = rtl822x_config_init,
+		.get_rate_matching = rtl822x_get_rate_matching,
+		.config_aneg    = rtl822x_c45_config_aneg,
+		.read_status    = rtl822x_c45_read_status,
+		.suspend        = genphy_c45_pma_suspend,
+		.resume         = rtlgen_c45_resume,
+	}, {
+		.match_phy_device = rtl8251b_c22_match_phy_device,
+		.name           = "RTL8251B 5Gbps PHY (C22)",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
 		.config_init    = rtl822x_config_init,
@@ -1169,6 +1294,15 @@ static struct phy_driver realtek_drvs[] = {
 		.resume         = rtlgen_resume,
 		.read_page      = rtl821x_read_page,
 		.write_page     = rtl821x_write_page,
+	}, {
+		.match_phy_device = rtl8251b_c45_match_phy_device,
+		.name           = "RTL8251B 5Gbps PHY (C45)",
+		.config_init    = rtl822x_config_init,
+		.get_rate_matching = rtl822x_get_rate_matching,
+		.config_aneg    = rtl822x_c45_config_aneg,
+		.read_status    = rtl822x_c45_read_status,
+		.suspend        = genphy_c45_pma_suspend,
+		.resume         = rtlgen_c45_resume,
 	}, {
 		PHY_ID_MATCH_EXACT(0x001cc961),
 		.name		= "RTL8366RB Gigabit Ethernet",
Signature · 1 line
2.42.1
#11 lore raw

PATCH v2 4/7 net: phy: realtek: Change rtlgen_get_speed() to rtlgen_decode_speed()

In reply to Eric Woudstra

The value of the register to determine the speed, is retrieved differently when using Clause 45 only. To use the rtlgen_get_speed() function in this case, pass the value of the register as argument to rtlgen_get_speed(). The function would then always return 0, so change it to void. A better name for this function now is rtlgen_decode_speed().

Add reading speed to rtl822x_c45_read_status().

---
 drivers/net/phy/realtek.c | 38 ++++++++++++++++++++++++--------------
 1 file changed, 24 insertions(+), 14 deletions(-)
drivers/net/phy/realtek.c +24 -14
index f9a67761878e..6449d8e0842c 100644
@@ -71,6 +71,8 @@
 
 #define RTL822X_VND2_GANLPAR				0xa414
 
+#define RTL822X_VND2_PHYSR				0xa434
+
 #define RTL8366RB_POWER_SAVE			0x15
 #define RTL8366RB_POWER_SAVE_ON			BIT(12)
 
@@ -551,17 +553,8 @@ static int rtl8366rb_config_init(struct phy_device *phydev)
 }
 
 /* get actual speed to cover the downshift case */
-static int rtlgen_get_speed(struct phy_device *phydev)
+static void rtlgen_decode_speed(struct phy_device *phydev, int val)
 {
-	int val;
-
-	if (!phydev->link)
-		return 0;
-
-	val = phy_read_paged(phydev, 0xa43, 0x12);
-	if (val < 0)
-		return val;
-
 	switch (val & RTLGEN_SPEED_MASK) {
 	case 0x0000:
 		phydev->speed = SPEED_10;
@@ -584,19 +577,26 @@ static int rtlgen_get_speed(struct phy_device *phydev)
 	default:
 		break;
 	}
-
-	return 0;
 }
 
 static int rtlgen_read_status(struct phy_device *phydev)
 {
-	int ret;
+	int ret, val;
 
 	ret = genphy_read_status(phydev);
 	if (ret < 0)
 		return ret;
 
-	return rtlgen_get_speed(phydev);
+	if (!phydev->link)
+		return 0;
+
+	val = phy_read_paged(phydev, 0xa43, 0x12);
+	if (val < 0)
+		return val;
+
+	rtlgen_decode_speed(phydev, val);
+
+	return 0;
 }
 
 static int rtlgen_read_mmd(struct phy_device *phydev, int devnum, u16 regnum)
@@ -881,6 +881,16 @@ static int rtl822x_c45_read_status(struct phy_device *phydev)
 		mii_stat1000_mod_linkmode_lpa_t(phydev->lp_advertising, val);
 	}
 
+	if (!phydev->link)
+		return 0;
+
+	/* Read actual speed from vendor register. */
+	val = phy_read_mmd(phydev, MDIO_MMD_VEND2, RTL822X_VND2_PHYSR);
+	if (val < 0)
+		return val;
+
+	rtlgen_decode_speed(phydev, val);
+
 	rtl822x_update_interface(phydev);
 
 	return 0;
Signature · 1 line
2.42.1
#12 lore raw

PATCH v2 5/7 net: phy: realtek: add rtl822x_c45_get_features() to set supported ports

In reply to Eric Woudstra

Sets ETHTOOL_LINK_MODE_TP_BIT and ETHTOOL_LINK_MODE_MII_BIT in phydev->supported.

---
 drivers/net/phy/realtek.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)
drivers/net/phy/realtek.c +13 -0
index 6449d8e0842c..3dc27a4f2c88 100644
@@ -836,6 +836,16 @@ static int rtl822x_read_status(struct phy_device *phydev)
 	return 0;
 }
 
+static int rtl822x_c45_get_features(struct phy_device *phydev)
+{
+	linkmode_set_bit(ETHTOOL_LINK_MODE_TP_BIT,
+			 phydev->supported);
+	linkmode_set_bit(ETHTOOL_LINK_MODE_MII_BIT,
+			 phydev->supported);
+
+	return genphy_c45_pma_read_abilities(phydev);
+}
+
 static int rtl822x_c45_config_aneg(struct phy_device *phydev)
 {
 	bool changed = false;
@@ -1267,6 +1277,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8221B-VB-CG 2.5Gbps PHY (C45)",
 		.config_init    = rtl822x_config_init,
 		.get_rate_matching = rtl822x_get_rate_matching,
+		.get_features   = rtl822x_c45_get_features,
 		.config_aneg    = rtl822x_c45_config_aneg,
 		.read_status    = rtl822x_c45_read_status,
 		.suspend        = genphy_c45_pma_suspend,
@@ -1288,6 +1299,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8221B-VN-CG 2.5Gbps PHY (C45)",
 		.config_init    = rtl822x_config_init,
 		.get_rate_matching = rtl822x_get_rate_matching,
+		.get_features   = rtl822x_c45_get_features,
 		.config_aneg    = rtl822x_c45_config_aneg,
 		.read_status    = rtl822x_c45_read_status,
 		.suspend        = genphy_c45_pma_suspend,
@@ -1309,6 +1321,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8251B 5Gbps PHY (C45)",
 		.config_init    = rtl822x_config_init,
 		.get_rate_matching = rtl822x_get_rate_matching,
+		.get_features   = rtl822x_c45_get_features,
 		.config_aneg    = rtl822x_c45_config_aneg,
 		.read_status    = rtl822x_c45_read_status,
 		.suspend        = genphy_c45_pma_suspend,
Signature · 1 line
2.42.1
#13 lore raw

PATCH v2 6/7 net: sfp: Fixup for OEM SFP-2.5G-T module

In reply to Eric Woudstra

Change from quirk to fixup for the OEM SFP-2.5G-T module.

Implementing this fixup, the rtl8221b phy is attached and the quirk is no longer used.

The module is re-branded to different brands, the one I have that applies to this patch is branded LuLeey.

---
 drivers/net/phy/sfp.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)
drivers/net/phy/sfp.c +8 -1
index f75c9eb3958e..191a6d5dc925 100644
@@ -385,6 +385,13 @@ static void sfp_fixup_rollball(struct sfp *sfp)
 	sfp->phy_t_retry = msecs_to_jiffies(1000);
 }
 
+// For 2.5GBASE-T short-reach modules
+static void sfp_fixup_oem_2_5gbaset(struct sfp *sfp)
+{
+	sfp_fixup_rollball(sfp);
+	sfp->id.base.extended_cc = SFF8024_ECC_2_5GBASE_T;
+}
+
 static void sfp_fixup_fs_10gt(struct sfp *sfp)
 {
 	sfp_fixup_10gbaset_30m(sfp);
@@ -503,7 +510,7 @@ static const struct sfp_quirk sfp_quirks[] = {
 	SFP_QUIRK_F("Walsun", "HXSX-ATRI-1", sfp_fixup_fs_10gt),
 
 	SFP_QUIRK_F("OEM", "SFP-10G-T", sfp_fixup_rollball_cc),
-	SFP_QUIRK_M("OEM", "SFP-2.5G-T", sfp_quirk_oem_2_5g),
+	SFP_QUIRK_F("OEM", "SFP-2.5G-T", sfp_fixup_oem_2_5gbaset),
 	SFP_QUIRK_F("OEM", "RTSFP-10", sfp_fixup_rollball_cc),
 	SFP_QUIRK_F("OEM", "RTSFP-10G", sfp_fixup_rollball_cc),
 	SFP_QUIRK_F("Turris", "RTSFP-10", sfp_fixup_rollball),
Signature · 1 line
2.42.1
#14 lore raw

PATCH v2 7/7 net: sfp: add quirk for another multigig RollBall transceiver

In reply to Eric Woudstra

From: Marek Behún <[email protected]>

Add quirk for another RollBall copper transceiver: Turris RTSFP-2.5G, containing 2.5g capable RTL8221B PHY.

---
 drivers/net/phy/sfp.c | 1 +
 1 file changed, 1 insertion(+)
drivers/net/phy/sfp.c +1 -0
index 191a6d5dc925..0476624bbca6 100644
@@ -513,6 +513,7 @@ static const struct sfp_quirk sfp_quirks[] = {
 	SFP_QUIRK_F("OEM", "SFP-2.5G-T", sfp_fixup_oem_2_5gbaset),
 	SFP_QUIRK_F("OEM", "RTSFP-10", sfp_fixup_rollball_cc),
 	SFP_QUIRK_F("OEM", "RTSFP-10G", sfp_fixup_rollball_cc),
+	SFP_QUIRK_F("Turris", "RTSFP-2.5G", sfp_fixup_rollball),
 	SFP_QUIRK_F("Turris", "RTSFP-10", sfp_fixup_rollball),
 	SFP_QUIRK_F("Turris", "RTSFP-10G", sfp_fixup_rollball),
 };
Signature · 1 line
2.42.1
#2 lore raw

Re: [PATCH v2 net-next 1/7] net: phy: realtek: configure SerDes mode for rtl822x/8251b PHYs

In reply to Eric Woudstra
Quoted 11 lines · Eric Woudstra

From: Alexander Couzens <[email protected]>

The rtl822x series and rtl8251b support switching SerDes mode between 2500base-x and sgmii based on the negotiated copper speed.

Configure this switching mode according to SerDes modes supported by host.

There is an additional datasheet for RTL8226B/RTL8221B called "SERDES MODE SETTING FLOW APPLICATION NOTE" where this sequence to setup interface and rate adapter mode.

Gramar doesn't parse, missing verb.

Quoted 190 lines

However, there is no documentation about the meaning of registers and bits, it's literally just magic numbers and pseudo-code.

[ refactored, dropped HiSGMII mode and changed commit message ]
[ changed rtl822x_update_interface() to use vendor register ]
[ always fill in possible interfaces ]
---
 drivers/net/phy/realtek.c | 99 ++++++++++++++++++++++++++++++++++++++-
 1 file changed, 97 insertions(+), 2 deletions(-)
drivers/net/phy/realtek.c +96 -2
index 1fa70427b2a2..8a876e003774 100644
@@ -54,6 +54,16 @@
 						 RTL8201F_ISR_LINK)
 #define RTL8201F_IER				0x13
 
+#define RTL822X_VND1_SERDES_OPTION			0x697a
+#define RTL822X_VND1_SERDES_OPTION_MODE_MASK		GENMASK(5, 0)
+#define RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX_SGMII		0
+#define RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX		2
+
+#define RTL822X_VND1_SERDES_CTRL3			0x7580
+#define RTL822X_VND1_SERDES_CTRL3_MODE_MASK		GENMASK(5, 0)
+#define RTL822X_VND1_SERDES_CTRL3_MODE_SGMII			0x02
+#define RTL822X_VND1_SERDES_CTRL3_MODE_2500BASEX		0x16
+
 #define RTL8366RB_POWER_SAVE			0x15
 #define RTL8366RB_POWER_SAVE_ON			BIT(12)
 
@@ -659,6 +669,60 @@ static int rtl822x_write_mmd(struct phy_device *phydev, int devnum, u16 regnum,
 	return ret;
 }
 
+static int rtl822x_config_init(struct phy_device *phydev)
+{
+	bool has_2500, has_sgmii;
+	u16 mode;
+	int ret;
+
+	has_2500 = test_bit(PHY_INTERFACE_MODE_2500BASEX,
+			    phydev->host_interfaces) ||
+		   phydev->interface == PHY_INTERFACE_MODE_2500BASEX;
+
+	has_sgmii = test_bit(PHY_INTERFACE_MODE_SGMII,
+			     phydev->host_interfaces) ||
+		    phydev->interface == PHY_INTERFACE_MODE_SGMII;
+
+	/* fill in possible interfaces */
+	__assign_bit(PHY_INTERFACE_MODE_2500BASEX, phydev->possible_interfaces,
+		     has_2500);
+	__assign_bit(PHY_INTERFACE_MODE_SGMII, phydev->possible_interfaces,
+		     has_sgmii);
+
+	if (!has_2500 && !has_sgmii)
+		return 0;
+
+	/* determine SerDes option mode */
+	if (has_2500 && !has_sgmii)
+		mode = RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX;
+	else
+		mode = RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX_SGMII;
+
+	/* the following sequence with magic numbers sets up the SerDes
+	 * option mode
+	 */
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x75f3, 0);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_modify_mmd_changed(phydev, MDIO_MMD_VEND1,
+				     RTL822X_VND1_SERDES_OPTION,
+				     RTL822X_VND1_SERDES_OPTION_MODE_MASK,
+				     mode);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x6a04, 0x0503);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x6f10, 0xd455);
+	if (ret < 0)
+		return ret;
+
+	return phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x6f11, 0x8020);
+}
+
 static int rtl822x_get_features(struct phy_device *phydev)
 {
 	int val;
@@ -695,6 +759,28 @@ static int rtl822x_config_aneg(struct phy_device *phydev)
 	return __genphy_config_aneg(phydev, ret);
 }
 
+static void rtl822x_update_interface(struct phy_device *phydev)
+{
+	int val;
+
+	if (!phydev->link)
+		return;
+
+	/* Change interface according to serdes mode */
+	val = phy_read_mmd(phydev, MDIO_MMD_VEND1, RTL822X_VND1_SERDES_CTRL3);
+	if (val < 0)
+		return;
+
+	switch (val & RTL822X_VND1_SERDES_CTRL3_MODE_MASK) {
+	case RTL822X_VND1_SERDES_CTRL3_MODE_2500BASEX:
+		phydev->interface = PHY_INTERFACE_MODE_2500BASEX;
+		break;
+	case RTL822X_VND1_SERDES_CTRL3_MODE_SGMII:
+		phydev->interface = PHY_INTERFACE_MODE_SGMII;
+		break;
+	}
+}
+
 static int rtl822x_read_status(struct phy_device *phydev)
 {
 	int ret;
@@ -709,11 +795,13 @@ static int rtl822x_read_status(struct phy_device *phydev)
 						  lpadv);
 	}
 
-	ret = genphy_read_status(phydev);
+	ret = rtlgen_read_status(phydev);
 	if (ret < 0)
 		return ret;
 
-	return rtlgen_get_speed(phydev);
+	rtl822x_update_interface(phydev);
+
+	return 0;
 }
 
 static bool rtlgen_supports_2_5gbps(struct phy_device *phydev)
@@ -976,6 +1064,7 @@ static struct phy_driver realtek_drvs[] = {
 		.match_phy_device = rtl8226_match_phy_device,
 		.get_features	= rtl822x_get_features,
 		.config_aneg	= rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status	= rtl822x_read_status,
 		.suspend	= genphy_suspend,
 		.resume		= rtlgen_resume,
@@ -988,6 +1077,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name		= "RTL8226B_RTL8221B 2.5Gbps PHY",
 		.get_features	= rtl822x_get_features,
 		.config_aneg	= rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status	= rtl822x_read_status,
 		.suspend	= genphy_suspend,
 		.resume		= rtlgen_resume,
@@ -1000,6 +1090,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8226-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
@@ -1010,6 +1101,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8226B-CG_RTL8221B-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
@@ -1019,6 +1111,7 @@ static struct phy_driver realtek_drvs[] = {
 		PHY_ID_MATCH_EXACT(0x001cc849),
 		.name           = "RTL8221B-VB-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
+		.config_init    = rtl822x_config_init,
 		.config_aneg    = rtl822x_config_aneg,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
@@ -1030,6 +1123,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8221B-VM-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,

drivers/net/phy/realtek.c static struct phy_driver realtek_drvs[] = { · line 1137

Quoted 4 lines
drivers/net/phy/realtek.c +1 -0
@@ -1040,6 +1134,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8251B 5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,

Have you tested this on RTL8251B?
This PHY usually uses 5GBase-R link mode with rate-adapter mode for lower speeds. Hence I'm pretty sure that also setting up SerDes mode register will be a bit different.

Quoted 6 lines
drivers/net/phy/realtek.c +0 -0
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
Signature · 1 line
2.42.1
#3 lore raw

Re: [PATCH v2 net-next 1/7] net: phy: realtek: configure SerDes mode for rtl822x/8251b PHYs

Quoted 5 lines · Daniel Golle
Quoted 3 lines

There is an additional datasheet for RTL8226B/RTL8221B called "SERDES MODE SETTING FLOW APPLICATION NOTE" where this sequence to setup interface and rate adapter mode.

Gramar doesn't parse, missing verb.

Thanks, I'll correct it.

Quoted 6 lines

Review

Quoted 1 line
(quoted diff) +1 -0
+		.config_init    = rtl822x_config_init,

Have you tested this on RTL8251B?
This PHY usually uses 5GBase-R link mode with rate-adapter mode for lower speeds. Hence I'm pretty sure that also setting up SerDes mode register will be a bit different.

Thanks, I'd better not add following lines for the rtl8251b (2x):

.config_init = rtl822x_config_init,
.get_rate_matching = rtl822x_get_rate_matching,

Until someone with the hardware can test it.

Perhaps we can find a RollBall sfp module that has one on it and use it on a BPI-R4...

maintainer
#4 lore raw

Re: [PATCH v2 net-next 1/7] net: phy: realtek: configure SerDes mode for rtl822x/8251b PHYs

In reply to Eric Woudstra
Quoted 153 lines · Eric Woudstra

From: Alexander Couzens <[email protected]>

The rtl822x series and rtl8251b support switching SerDes mode between 2500base-x and sgmii based on the negotiated copper speed.

Configure this switching mode according to SerDes modes supported by host.

There is an additional datasheet for RTL8226B/RTL8221B called "SERDES MODE SETTING FLOW APPLICATION NOTE" where this sequence to setup interface and rate adapter mode.

However, there is no documentation about the meaning of registers and bits, it's literally just magic numbers and pseudo-code.

[ refactored, dropped HiSGMII mode and changed commit message ]
[ changed rtl822x_update_interface() to use vendor register ]
[ always fill in possible interfaces ]
---
 drivers/net/phy/realtek.c | 99 ++++++++++++++++++++++++++++++++++++++-
 1 file changed, 97 insertions(+), 2 deletions(-)
drivers/net/phy/realtek.c +90 -2
index 1fa70427b2a2..8a876e003774 100644
@@ -54,6 +54,16 @@
 						 RTL8201F_ISR_LINK)
 #define RTL8201F_IER				0x13
 
+#define RTL822X_VND1_SERDES_OPTION			0x697a
+#define RTL822X_VND1_SERDES_OPTION_MODE_MASK		GENMASK(5, 0)
+#define RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX_SGMII		0
+#define RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX		2
+
+#define RTL822X_VND1_SERDES_CTRL3			0x7580
+#define RTL822X_VND1_SERDES_CTRL3_MODE_MASK		GENMASK(5, 0)
+#define RTL822X_VND1_SERDES_CTRL3_MODE_SGMII			0x02
+#define RTL822X_VND1_SERDES_CTRL3_MODE_2500BASEX		0x16
+
 #define RTL8366RB_POWER_SAVE			0x15
 #define RTL8366RB_POWER_SAVE_ON			BIT(12)
 
@@ -659,6 +669,60 @@ static int rtl822x_write_mmd(struct phy_device *phydev, int devnum, u16 regnum,
 	return ret;
 }
 
+static int rtl822x_config_init(struct phy_device *phydev)
+{
+	bool has_2500, has_sgmii;
+	u16 mode;
+	int ret;
+
+	has_2500 = test_bit(PHY_INTERFACE_MODE_2500BASEX,
+			    phydev->host_interfaces) ||
+		   phydev->interface == PHY_INTERFACE_MODE_2500BASEX;
+
+	has_sgmii = test_bit(PHY_INTERFACE_MODE_SGMII,
+			     phydev->host_interfaces) ||
+		    phydev->interface == PHY_INTERFACE_MODE_SGMII;
+
+	/* fill in possible interfaces */
+	__assign_bit(PHY_INTERFACE_MODE_2500BASEX, phydev->possible_interfaces,
+		     has_2500);
+	__assign_bit(PHY_INTERFACE_MODE_SGMII, phydev->possible_interfaces,
+		     has_sgmii);
+
+	if (!has_2500 && !has_sgmii)
+		return 0;
+
+	/* determine SerDes option mode */
+	if (has_2500 && !has_sgmii)
+		mode = RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX;
+	else
+		mode = RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX_SGMII;
+
+	/* the following sequence with magic numbers sets up the SerDes
+	 * option mode
+	 */
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x75f3, 0);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_modify_mmd_changed(phydev, MDIO_MMD_VEND1,
+				     RTL822X_VND1_SERDES_OPTION,
+				     RTL822X_VND1_SERDES_OPTION_MODE_MASK,
+				     mode);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x6a04, 0x0503);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x6f10, 0xd455);
+	if (ret < 0)
+		return ret;
+
+	return phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x6f11, 0x8020);
+}
+
 static int rtl822x_get_features(struct phy_device *phydev)
 {
 	int val;
@@ -695,6 +759,28 @@ static int rtl822x_config_aneg(struct phy_device *phydev)
 	return __genphy_config_aneg(phydev, ret);
 }
 
+static void rtl822x_update_interface(struct phy_device *phydev)
+{
+	int val;
+
+	if (!phydev->link)
+		return;
+
+	/* Change interface according to serdes mode */
+	val = phy_read_mmd(phydev, MDIO_MMD_VEND1, RTL822X_VND1_SERDES_CTRL3);
+	if (val < 0)
+		return;
+
+	switch (val & RTL822X_VND1_SERDES_CTRL3_MODE_MASK) {
+	case RTL822X_VND1_SERDES_CTRL3_MODE_2500BASEX:
+		phydev->interface = PHY_INTERFACE_MODE_2500BASEX;
+		break;
+	case RTL822X_VND1_SERDES_CTRL3_MODE_SGMII:
+		phydev->interface = PHY_INTERFACE_MODE_SGMII;
+		break;
+	}
+}
+
 static int rtl822x_read_status(struct phy_device *phydev)
 {
 	int ret;
@@ -709,11 +795,13 @@ static int rtl822x_read_status(struct phy_device *phydev)
 						  lpadv);
 	}
 
-	ret = genphy_read_status(phydev);
+	ret = rtlgen_read_status(phydev);
 	if (ret < 0)
 		return ret;
 
-	return rtlgen_get_speed(phydev);
+	rtl822x_update_interface(phydev);
+
+	return 0;
 }
 
 static bool rtlgen_supports_2_5gbps(struct phy_device *phydev)

drivers/net/phy/realtek.c static struct phy_driver realtek_drvs[] = { · line 1067

Quoted 4 lines
drivers/net/phy/realtek.c +1 -0
@@ -976,6 +1064,7 @@ static struct phy_driver realtek_drvs[] = {
 		.match_phy_device = rtl8226_match_phy_device,
 		.get_features	= rtl822x_get_features,
 		.config_aneg	= rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,

Did you test this (and the rest of the series) on RTL8125A, where MMD register access for the integrated 2.5G PHY isn't supported?

Quoted 51 lines
drivers/net/phy/realtek.c +6 -0
 		.read_status	= rtl822x_read_status,
 		.suspend	= genphy_suspend,
 		.resume		= rtlgen_resume,
@@ -988,6 +1077,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name		= "RTL8226B_RTL8221B 2.5Gbps PHY",
 		.get_features	= rtl822x_get_features,
 		.config_aneg	= rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status	= rtl822x_read_status,
 		.suspend	= genphy_suspend,
 		.resume		= rtlgen_resume,
@@ -1000,6 +1090,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8226-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
@@ -1010,6 +1101,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8226B-CG_RTL8221B-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
@@ -1019,6 +1111,7 @@ static struct phy_driver realtek_drvs[] = {
 		PHY_ID_MATCH_EXACT(0x001cc849),
 		.name           = "RTL8221B-VB-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
+		.config_init    = rtl822x_config_init,
 		.config_aneg    = rtl822x_config_aneg,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
@@ -1030,6 +1123,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8221B-VM-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
@@ -1040,6 +1134,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8251B 5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
#5 lore raw

Re: [PATCH v2 net-next 1/7] net: phy: realtek: configure SerDes mode for rtl822x/8251b PHYs

Quoted 152 lines · Heiner Kallweit
Quoted 151 lines · Eric Woudstra

From: Alexander Couzens <[email protected]>

The rtl822x series and rtl8251b support switching SerDes mode between 2500base-x and sgmii based on the negotiated copper speed.

Configure this switching mode according to SerDes modes supported by host.

There is an additional datasheet for RTL8226B/RTL8221B called "SERDES MODE SETTING FLOW APPLICATION NOTE" where this sequence to setup interface and rate adapter mode.

However, there is no documentation about the meaning of registers and bits, it's literally just magic numbers and pseudo-code.

[ refactored, dropped HiSGMII mode and changed commit message ]
[ changed rtl822x_update_interface() to use vendor register ]
[ always fill in possible interfaces ]
---
 drivers/net/phy/realtek.c | 99 ++++++++++++++++++++++++++++++++++++++-
 1 file changed, 97 insertions(+), 2 deletions(-)
drivers/net/phy/realtek.c +90 -2
index 1fa70427b2a2..8a876e003774 100644
@@ -54,6 +54,16 @@
 						 RTL8201F_ISR_LINK)
 #define RTL8201F_IER				0x13
 
+#define RTL822X_VND1_SERDES_OPTION			0x697a
+#define RTL822X_VND1_SERDES_OPTION_MODE_MASK		GENMASK(5, 0)
+#define RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX_SGMII		0
+#define RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX		2
+
+#define RTL822X_VND1_SERDES_CTRL3			0x7580
+#define RTL822X_VND1_SERDES_CTRL3_MODE_MASK		GENMASK(5, 0)
+#define RTL822X_VND1_SERDES_CTRL3_MODE_SGMII			0x02
+#define RTL822X_VND1_SERDES_CTRL3_MODE_2500BASEX		0x16
+
 #define RTL8366RB_POWER_SAVE			0x15
 #define RTL8366RB_POWER_SAVE_ON			BIT(12)
 
@@ -659,6 +669,60 @@ static int rtl822x_write_mmd(struct phy_device *phydev, int devnum, u16 regnum,
 	return ret;
 }
 
+static int rtl822x_config_init(struct phy_device *phydev)
+{
+	bool has_2500, has_sgmii;
+	u16 mode;
+	int ret;
+
+	has_2500 = test_bit(PHY_INTERFACE_MODE_2500BASEX,
+			    phydev->host_interfaces) ||
+		   phydev->interface == PHY_INTERFACE_MODE_2500BASEX;
+
+	has_sgmii = test_bit(PHY_INTERFACE_MODE_SGMII,
+			     phydev->host_interfaces) ||
+		    phydev->interface == PHY_INTERFACE_MODE_SGMII;
+
+	/* fill in possible interfaces */
+	__assign_bit(PHY_INTERFACE_MODE_2500BASEX, phydev->possible_interfaces,
+		     has_2500);
+	__assign_bit(PHY_INTERFACE_MODE_SGMII, phydev->possible_interfaces,
+		     has_sgmii);
+
+	if (!has_2500 && !has_sgmii)
+		return 0;
+
+	/* determine SerDes option mode */
+	if (has_2500 && !has_sgmii)
+		mode = RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX;
+	else
+		mode = RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX_SGMII;
+
+	/* the following sequence with magic numbers sets up the SerDes
+	 * option mode
+	 */
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x75f3, 0);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_modify_mmd_changed(phydev, MDIO_MMD_VEND1,
+				     RTL822X_VND1_SERDES_OPTION,
+				     RTL822X_VND1_SERDES_OPTION_MODE_MASK,
+				     mode);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x6a04, 0x0503);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x6f10, 0xd455);
+	if (ret < 0)
+		return ret;
+
+	return phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x6f11, 0x8020);
+}
+
 static int rtl822x_get_features(struct phy_device *phydev)
 {
 	int val;
@@ -695,6 +759,28 @@ static int rtl822x_config_aneg(struct phy_device *phydev)
 	return __genphy_config_aneg(phydev, ret);
 }
 
+static void rtl822x_update_interface(struct phy_device *phydev)
+{
+	int val;
+
+	if (!phydev->link)
+		return;
+
+	/* Change interface according to serdes mode */
+	val = phy_read_mmd(phydev, MDIO_MMD_VEND1, RTL822X_VND1_SERDES_CTRL3);
+	if (val < 0)
+		return;
+
+	switch (val & RTL822X_VND1_SERDES_CTRL3_MODE_MASK) {
+	case RTL822X_VND1_SERDES_CTRL3_MODE_2500BASEX:
+		phydev->interface = PHY_INTERFACE_MODE_2500BASEX;
+		break;
+	case RTL822X_VND1_SERDES_CTRL3_MODE_SGMII:
+		phydev->interface = PHY_INTERFACE_MODE_SGMII;
+		break;
+	}
+}
+
 static int rtl822x_read_status(struct phy_device *phydev)
 {
 	int ret;
@@ -709,11 +795,13 @@ static int rtl822x_read_status(struct phy_device *phydev)
 						  lpadv);
 	}
 
-	ret = genphy_read_status(phydev);
+	ret = rtlgen_read_status(phydev);
 	if (ret < 0)
 		return ret;
 
-	return rtlgen_get_speed(phydev);
+	rtl822x_update_interface(phydev);
+
+	return 0;
 }
 
Quoted 9 lines

drivers/net/phy/realtek.c static struct phy_driver realtek_drvs[] = { · line 1067

Quoted 6 lines
drivers/net/phy/realtek.c +1 -0
 static bool rtlgen_supports_2_5gbps(struct phy_device *phydev)
@@ -976,6 +1064,7 @@ static struct phy_driver realtek_drvs[] = {
 		.match_phy_device = rtl8226_match_phy_device,
 		.get_features	= rtl822x_get_features,
 		.config_aneg	= rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,

Did you test this (and the rest of the series) on RTL8125A, where MMD register access for the integrated 2.5G PHY isn't supported?

None of this should be done on RealTek NICs, and the easiest way to prevent that is to test if phydev->phylink is NULL or not (as the NIC driver doesn't use phylink but rather just calls phy_connect_direct()).

Also note that the datasheet with the magic SerDes config sequences lists only 2nd generation 2.5G PHYs as supported:
RTL8226B
RTL8221B(I)
RTL8221B(I)-VB
RTL8221B(I)-VM

So RTL8226 and RTL8226-CG are **not** listed there and being from the 1st generation of RealTek 2.5G PHYs I would assume that it won't support setting up the SerDes mode in this way.

Afaik those anyway were only used in early RealTek-based 2.5G switches and maybe NICs, I'm pretty sure you won't find them inside SFP modules or as part non-RealTek-based routers or switches -- hence switching SerDes mode most likely anyway will never be required for those.

Quoted 53 lines
Quoted 52 lines
drivers/net/phy/realtek.c +6 -0
 		.read_status	= rtl822x_read_status,
 		.suspend	= genphy_suspend,
 		.resume		= rtlgen_resume,
@@ -988,6 +1077,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name		= "RTL8226B_RTL8221B 2.5Gbps PHY",
 		.get_features	= rtl822x_get_features,
 		.config_aneg	= rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status	= rtl822x_read_status,
 		.suspend	= genphy_suspend,
 		.resume		= rtlgen_resume,
@@ -1000,6 +1090,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8226-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
@@ -1010,6 +1101,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8226B-CG_RTL8221B-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
@@ -1019,6 +1111,7 @@ static struct phy_driver realtek_drvs[] = {
 		PHY_ID_MATCH_EXACT(0x001cc849),
 		.name           = "RTL8221B-VB-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
+		.config_init    = rtl822x_config_init,
 		.config_aneg    = rtl822x_config_aneg,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
@@ -1030,6 +1123,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8221B-VM-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
@@ -1040,6 +1134,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8251B 5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
maintainer
#6 lore raw

Re: [PATCH v2 net-next 1/7] net: phy: realtek: configure SerDes mode for rtl822x/8251b PHYs

Quoted 163 lines · Daniel Golle
Quoted 152 lines · Heiner Kallweit
Quoted 151 lines · Eric Woudstra

From: Alexander Couzens <[email protected]>

The rtl822x series and rtl8251b support switching SerDes mode between 2500base-x and sgmii based on the negotiated copper speed.

Configure this switching mode according to SerDes modes supported by host.

There is an additional datasheet for RTL8226B/RTL8221B called "SERDES MODE SETTING FLOW APPLICATION NOTE" where this sequence to setup interface and rate adapter mode.

However, there is no documentation about the meaning of registers and bits, it's literally just magic numbers and pseudo-code.

[ refactored, dropped HiSGMII mode and changed commit message ]
[ changed rtl822x_update_interface() to use vendor register ]
[ always fill in possible interfaces ]
---
 drivers/net/phy/realtek.c | 99 ++++++++++++++++++++++++++++++++++++++-
 1 file changed, 97 insertions(+), 2 deletions(-)
drivers/net/phy/realtek.c +90 -2
index 1fa70427b2a2..8a876e003774 100644
@@ -54,6 +54,16 @@
 						 RTL8201F_ISR_LINK)
 #define RTL8201F_IER				0x13
 
+#define RTL822X_VND1_SERDES_OPTION			0x697a
+#define RTL822X_VND1_SERDES_OPTION_MODE_MASK		GENMASK(5, 0)
+#define RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX_SGMII		0
+#define RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX		2
+
+#define RTL822X_VND1_SERDES_CTRL3			0x7580
+#define RTL822X_VND1_SERDES_CTRL3_MODE_MASK		GENMASK(5, 0)
+#define RTL822X_VND1_SERDES_CTRL3_MODE_SGMII			0x02
+#define RTL822X_VND1_SERDES_CTRL3_MODE_2500BASEX		0x16
+
 #define RTL8366RB_POWER_SAVE			0x15
 #define RTL8366RB_POWER_SAVE_ON			BIT(12)
 
@@ -659,6 +669,60 @@ static int rtl822x_write_mmd(struct phy_device *phydev, int devnum, u16 regnum,
 	return ret;
 }
 
+static int rtl822x_config_init(struct phy_device *phydev)
+{
+	bool has_2500, has_sgmii;
+	u16 mode;
+	int ret;
+
+	has_2500 = test_bit(PHY_INTERFACE_MODE_2500BASEX,
+			    phydev->host_interfaces) ||
+		   phydev->interface == PHY_INTERFACE_MODE_2500BASEX;
+
+	has_sgmii = test_bit(PHY_INTERFACE_MODE_SGMII,
+			     phydev->host_interfaces) ||
+		    phydev->interface == PHY_INTERFACE_MODE_SGMII;
+
+	/* fill in possible interfaces */
+	__assign_bit(PHY_INTERFACE_MODE_2500BASEX, phydev->possible_interfaces,
+		     has_2500);
+	__assign_bit(PHY_INTERFACE_MODE_SGMII, phydev->possible_interfaces,
+		     has_sgmii);
+
+	if (!has_2500 && !has_sgmii)
+		return 0;
+
+	/* determine SerDes option mode */
+	if (has_2500 && !has_sgmii)
+		mode = RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX;
+	else
+		mode = RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX_SGMII;
+
+	/* the following sequence with magic numbers sets up the SerDes
+	 * option mode
+	 */
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x75f3, 0);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_modify_mmd_changed(phydev, MDIO_MMD_VEND1,
+				     RTL822X_VND1_SERDES_OPTION,
+				     RTL822X_VND1_SERDES_OPTION_MODE_MASK,
+				     mode);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x6a04, 0x0503);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x6f10, 0xd455);
+	if (ret < 0)
+		return ret;
+
+	return phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x6f11, 0x8020);
+}
+
 static int rtl822x_get_features(struct phy_device *phydev)
 {
 	int val;
@@ -695,6 +759,28 @@ static int rtl822x_config_aneg(struct phy_device *phydev)
 	return __genphy_config_aneg(phydev, ret);
 }
 
+static void rtl822x_update_interface(struct phy_device *phydev)
+{
+	int val;
+
+	if (!phydev->link)
+		return;
+
+	/* Change interface according to serdes mode */
+	val = phy_read_mmd(phydev, MDIO_MMD_VEND1, RTL822X_VND1_SERDES_CTRL3);
+	if (val < 0)
+		return;
+
+	switch (val & RTL822X_VND1_SERDES_CTRL3_MODE_MASK) {
+	case RTL822X_VND1_SERDES_CTRL3_MODE_2500BASEX:
+		phydev->interface = PHY_INTERFACE_MODE_2500BASEX;
+		break;
+	case RTL822X_VND1_SERDES_CTRL3_MODE_SGMII:
+		phydev->interface = PHY_INTERFACE_MODE_SGMII;
+		break;
+	}
+}
+
 static int rtl822x_read_status(struct phy_device *phydev)
 {
 	int ret;
@@ -709,11 +795,13 @@ static int rtl822x_read_status(struct phy_device *phydev)
 						  lpadv);
 	}
 
-	ret = genphy_read_status(phydev);
+	ret = rtlgen_read_status(phydev);
 	if (ret < 0)
 		return ret;
 
-	return rtlgen_get_speed(phydev);
+	rtl822x_update_interface(phydev);
+
+	return 0;
 }
 
Quoted 9 lines

drivers/net/phy/realtek.c static struct phy_driver realtek_drvs[] = { · line 1067

Quoted 6 lines
drivers/net/phy/realtek.c +1 -0
 static bool rtlgen_supports_2_5gbps(struct phy_device *phydev)
@@ -976,6 +1064,7 @@ static struct phy_driver realtek_drvs[] = {
 		.match_phy_device = rtl8226_match_phy_device,
 		.get_features	= rtl822x_get_features,
 		.config_aneg	= rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,

Did you test this (and the rest of the series) on RTL8125A, where MMD register access for the integrated 2.5G PHY isn't supported?

Quoted 4 lines

None of this should be done on RealTek NICs, and the easiest way to prevent that is to test if phydev->phylink is NULL or not (as the NIC driver doesn't use phylink but rather just calls phy_connect_direct()).

Right. I'm asking because this PHY driver entry is used on RTL8125A.

Quoted 69 lines

Also note that the datasheet with the magic SerDes config sequences lists only 2nd generation 2.5G PHYs as supported:
RTL8226B
RTL8221B(I)
RTL8221B(I)-VB
RTL8221B(I)-VM

So RTL8226 and RTL8226-CG are **not** listed there and being from the 1st generation of RealTek 2.5G PHYs I would assume that it won't support setting up the SerDes mode in this way.

Afaik those anyway were only used in early RealTek-based 2.5G switches and maybe NICs, I'm pretty sure you won't find them inside SFP modules or as part non-RealTek-based routers or switches -- hence switching SerDes mode most likely anyway will never be required for those.

Quoted 53 lines
Quoted 52 lines
drivers/net/phy/realtek.c +6 -0
 		.read_status	= rtl822x_read_status,
 		.suspend	= genphy_suspend,
 		.resume		= rtlgen_resume,
@@ -988,6 +1077,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name		= "RTL8226B_RTL8221B 2.5Gbps PHY",
 		.get_features	= rtl822x_get_features,
 		.config_aneg	= rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status	= rtl822x_read_status,
 		.suspend	= genphy_suspend,
 		.resume		= rtlgen_resume,
@@ -1000,6 +1090,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8226-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
@@ -1010,6 +1101,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8226B-CG_RTL8221B-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
@@ -1019,6 +1111,7 @@ static struct phy_driver realtek_drvs[] = {
 		PHY_ID_MATCH_EXACT(0x001cc849),
 		.name           = "RTL8221B-VB-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
+		.config_init    = rtl822x_config_init,
 		.config_aneg    = rtl822x_config_aneg,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
@@ -1030,6 +1123,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8221B-VM-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
@@ -1040,6 +1134,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8251B 5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
+		.config_init    = rtl822x_config_init,
 		.read_status    = rtl822x_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
#7 lore raw

Re: [PATCH v2 net-next 1/7] net: phy: realtek: configure SerDes mode for rtl822x/8251b PHYs

In reply to Daniel Golle
Quoted 7 lines · Daniel Golle
Quoted 2 lines · Heiner Kallweit

Did you test this (and the rest of the series) on RTL8125A, where MMD register access for the integrated 2.5G PHY isn't supported?

None of this should be done on RealTek NICs, and the easiest way to prevent that is to test if phydev->phylink is NULL or not (as the NIC driver doesn't use phylink but rather just calls phy_connect_direct()).

Ewwwwwwwwwwwwwwwww. Please do not use the presence of phydev->phylink to change driver behaviour. That's just... disgusting.

Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
#8 lore raw

Re: [PATCH v2 net-next 1/7] net: phy: realtek: configure SerDes mode for rtl822x/8251b PHYs

In reply to Daniel Golle
Quoted 11 lines · Daniel Golle

None of this should be done on RealTek NICs, and the easiest way to prevent that is to test if phydev->phylink is NULL or not (as the NIC driver doesn't use phylink but rather just calls phy_connect_direct()).

Also note that the datasheet with the magic SerDes config sequences lists only 2nd generation 2.5G PHYs as supported:
RTL8226B
RTL8221B(I)
RTL8221B(I)-VB
RTL8221B(I)-VM

Quoted 8 lines

So RTL8226 and RTL8226-CG are **not** listed there and being from the 1st generation of RealTek 2.5G PHYs I would assume that it won't support setting up the SerDes mode in this way.

Afaik those anyway were only used in early RealTek-based 2.5G switches and maybe NICs, I'm pretty sure you won't find them inside SFP modules or as part non-RealTek-based routers or switches -- hence switching SerDes mode most likely anyway will never be required for those.

Then it would be best to change all patches in this patch-set to only modify the driver instances of:

"RTL8226B_RTL8221B 2.5Gbps PHY"
"RTL8226B-CG_RTL8221B-CG 2.5Gbps PHY"
"RTL8221B-VB-CG 2.5Gbps PHY"
"RTL8221B-VM-CG 2.5Gbps PHY"

And NOT to modify:

"RTL8226 2.5Gbps PHY
"RTL8226-CG 2.5Gbps PHY"
"RTL8251B 5Gbps PHY"

Or are there more restrictions? If so, why is it a restriction? Perhaps this can help me find an expression to use as match.

Best regards,

Eric Woudstra