riscv: dts: starfive: jh7110-milkv-mars: enable usb0 host function
Subsystems (3)
v6 cover riscv: dts: starfive: jh7110-milkv-mars: enable usb0 host function
Enable host mode JH7110 on-chip USB for Milk-V Mars by setting host mode and connect vbus pinctrl.
This functionality depends on setting the USB over-current register to disable at bootloader phase, for example U-Boot:
https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/
If the over-current register is not prepared for us then the result is no change in functional outcome with this patch applied; there is an error visible to the user and this additional usb configuration fails (same as it is now). On Milk-V Mars with four USB-A ports this applies to one of the USB-A ports and the remaining three VL805-connected USB-A ports via PCIe are not changed.
Changes since v5:
- Rebase on latest master
- Addtional detail to commit description
Changes since v4:
- Rebase on latest master
Changes since v3:
- Rebase on linux-next/master
- use tabs for code indent
Changes since v2:
- Rebase on 6.12
E Shattow (1):
riscv: dts: starfive: jh7110-milkv-mars: enable usb0 host function
.../boot/dts/starfive/jh7110-milkv-mars.dts | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-)
Signature · 1 line
2.45.2
PATCH v6 1/1 riscv: dts: starfive: jh7110-milkv-mars: enable usb0 host function
Milk-V Mars board routes one of four USB-A ports to USB0 on the SoC rather than to the VL805 USB 3.0 <-> PCIe chip.
Set JH7110 on-chip USB host mode and vbus pin assignment accordingly.
--- .../boot/dts/starfive/jh7110-milkv-mars.dts | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-)
arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts +17 -1
@@ -53,7 +53,23 @@ &spi0 { status = "okay"; }; +&sysgpio { + usb0_pins: usb0-0 { + vbus-pins { + pinmux = <GPIOMUX(25, GPOUT_SYS_USB_DRIVE_VBUS, + GPOEN_ENABLE, + GPI_NONE)>; + bias-disable; + input-disable; + input-schmitt-disable; + slew-rate = <0>; + }; + }; +}; + &usb0 { - dr_mode = "peripheral"; + dr_mode = "host"; + pinctrl-names = "default"; + pinctrl-0 = <&usb0_pins>; status = "okay"; };
Signature · 1 line
2.45.2
From: Conor Dooley <[email protected]>
Quoted 8 lines · E Shattow
Enable host mode JH7110 on-chip USB for Milk-V Mars by setting host mode and connect vbus pinctrl.
This functionality depends on setting the USB over-current register to disable at bootloader phase, for example U-Boot:
https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/[...]
Applied to riscv-dt-for-next, thanks!
[1/1] riscv: dts: starfive: jh7110-milkv-mars: enable usb0 host function
https://git.kernel.org/conor/c/708d55db3edb
Thanks,
Conor.