Skip to contentSkip to conversation

wifi: ath9k: add ahb OF support

PATCH Superseded Rosen Penev 2 participants 9 messages May 22, 2025 – May 23, 2025

Subsystems (4)

v2 of 5 Superseded Latest is v5 →

lore
Share & tools
lore
#0 lore raw

v2 cover wifi: ath9k: add ahb OF support

First two commits are small cleanups to make the changes of the third simpler. The fourth actually adds dts definitions to use ahb.

v2: Add documentation, use kernel_ulong_t, and of_device_get_match_data

Rosen Penev (5):
wifi: ath9k: ahb: reorder declarations
wifi: ath9k: ahb: reorder includes
wifi: ath9k: ahb: replace id_table with of
dt-bindings: net: wireless: ath9k: add OF bindings
mips: dts: qca: add wmac support

 .../bindings/net/wireless/qca,ath9k.yaml      | 23 ++++++-
 arch/mips/boot/dts/qca/ar9132.dtsi            |  9 +++
 .../boot/dts/qca/ar9132_tl_wr1043nd_v1.dts    |  4 ++
 arch/mips/boot/dts/qca/ar9331.dtsi            |  9 +++
 arch/mips/boot/dts/qca/ar9331_dpt_module.dts  |  4 ++
 .../mips/boot/dts/qca/ar9331_dragino_ms14.dts |  4 ++
 arch/mips/boot/dts/qca/ar9331_omega.dts       |  4 ++
 .../qca/ar9331_openembed_som9331_board.dts    |  4 ++
 arch/mips/boot/dts/qca/ar9331_tl_mr3020.dts   |  4 ++
 drivers/net/wireless/ath/ath9k/ahb.c          | 60 +++++++------------
 10 files changed, 84 insertions(+), 41 deletions(-)
Signature · 1 line
2.49.0
#1 lore raw

PATCH v2 1/5 wifi: ath9k: ahb: reorder declarations

Easier to look at. Follows netdev style.

Also remove ret assignment. Because of all of these devm conversions, ret = 0 is a path that never gets hit. The first time it does it when request_irq fails, but that ends up reassigning it.

---
 drivers/net/wireless/ath/ath9k/ahb.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)
drivers/net/wireless/ath/ath9k/ahb.c +5 -5
index 49b7ab26c477..d2a97e74f451 100644
@@ -71,14 +71,14 @@ static const struct ath_bus_ops ath_ahb_bus_ops  = {
 
 static int ath_ahb_probe(struct platform_device *pdev)
 {
-	void __iomem *mem;
-	struct ath_softc *sc;
-	struct ieee80211_hw *hw;
 	const struct platform_device_id *id = platform_get_device_id(pdev);
-	int irq;
-	int ret = 0;
+	struct ieee80211_hw *hw;
+	struct ath_softc *sc;
 	struct ath_hw *ah;
+	void __iomem *mem;
 	char hw_name[64];
+	int irq;
+	int ret;
 
 	if (!dev_get_platdata(&pdev->dev)) {
 		dev_err(&pdev->dev, "no platform data specified\n");
Signature · 1 line
2.49.0
#2 lore raw

PATCH v2 2/5 wifi: ath9k: ahb: reorder includes

In reply to Rosen Penev

Alphabetic includes are easier to look at and to make further changes to them.

---
 drivers/net/wireless/ath/ath9k/ahb.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/net/wireless/ath/ath9k/ahb.c +3 -2
index d2a97e74f451..1ffec827ed87 100644
@@ -16,10 +16,11 @@
  * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
  */
 
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
 #include <linux/nl80211.h>
 #include <linux/platform_device.h>
-#include <linux/module.h>
-#include <linux/mod_devicetable.h>
+
 #include "ath9k.h"
 
 static const struct platform_device_id ath9k_platform_id_table[] = {
Signature · 1 line
2.49.0
#3 lore raw

PATCH v2 3/5 wifi: ath9k: ahb: replace id_table with of

In reply to Rosen Penev

Since 2b0996c7646 , all of this platform code became no-op with no OF replacement. Not only that, there are no users of AHB here. Add an OF match table that mostly mirrors the original platform device id table. Use a qca prefix as is done for the only other property: qca,no-eeprom. Also used qca prefix for ar9530 as the latter seems to be a mistake.

This will be used to add ath9k support for the various ath79 devices here.

---
 drivers/net/wireless/ath/ath9k/ahb.c | 47 ++++++++--------------------
 1 file changed, 13 insertions(+), 34 deletions(-)
drivers/net/wireless/ath/ath9k/ahb.c +13 -34
index 1ffec827ed87..d8b13aa329ee 100644
@@ -19,35 +19,18 @@
 #include <linux/mod_devicetable.h>
 #include <linux/module.h>
 #include <linux/nl80211.h>
+#include <linux/of.h>
 #include <linux/platform_device.h>
 
 #include "ath9k.h"
 
-static const struct platform_device_id ath9k_platform_id_table[] = {
-	{
-		.name = "ath9k",
-		.driver_data = AR5416_AR9100_DEVID,
-	},
-	{
-		.name = "ar933x_wmac",
-		.driver_data = AR9300_DEVID_AR9330,
-	},
-	{
-		.name = "ar934x_wmac",
-		.driver_data = AR9300_DEVID_AR9340,
-	},
-	{
-		.name = "qca955x_wmac",
-		.driver_data = AR9300_DEVID_QCA955X,
-	},
-	{
-		.name = "qca953x_wmac",
-		.driver_data = AR9300_DEVID_AR953X,
-	},
-	{
-		.name = "qca956x_wmac",
-		.driver_data = AR9300_DEVID_QCA956X,
-	},
+static const struct of_device_id ath9k_of_match_table[] = {
+	{ .compatible = "qca,ar9130-wmac", .data = (void *)AR5416_AR9100_DEVID },
+	{ .compatible = "qca,ar9330-wmac", .data = (void *)AR9300_DEVID_AR9330 },
+	{ .compatible = "qca,ar9340-wmac", .data = (void *)AR9300_DEVID_AR9340 },
+	{ .compatible = "qca,qca9530-wmac", .data = (void *)AR9300_DEVID_AR953X },
+	{ .compatible = "qca,qca9550-wmac", .data = (void *)AR9300_DEVID_QCA955X },
+	{ .compatible = "qca,qca9560-wmac", .data = (void *)AR9300_DEVID_QCA956X },
 	{},
 };
 
@@ -72,20 +55,15 @@ static const struct ath_bus_ops ath_ahb_bus_ops  = {
 
 static int ath_ahb_probe(struct platform_device *pdev)
 {
-	const struct platform_device_id *id = platform_get_device_id(pdev);
 	struct ieee80211_hw *hw;
 	struct ath_softc *sc;
 	struct ath_hw *ah;
 	void __iomem *mem;
 	char hw_name[64];
+	u16 dev_id;
 	int irq;
 	int ret;
 
-	if (!dev_get_platdata(&pdev->dev)) {
-		dev_err(&pdev->dev, "no platform data specified\n");
-		return -EINVAL;
-	}
-
 	mem = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(mem)) {
 		dev_err(&pdev->dev, "ioremap failed\n");
@@ -118,7 +96,8 @@ static int ath_ahb_probe(struct platform_device *pdev)
 		goto err_free_hw;
 	}
 
-	ret = ath9k_init_device(id->driver_data, sc, &ath_ahb_bus_ops);
+	dev_id = (u16)(kernel_ulong_t)of_device_get_match_data(&pdev->dev);
+	ret = ath9k_init_device(dev_id, sc, &ath_ahb_bus_ops);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to initialize device\n");
 		goto err_irq;
@@ -156,11 +135,11 @@ static struct platform_driver ath_ahb_driver = {
 	.remove = ath_ahb_remove,
 	.driver = {
 		.name = "ath9k",
+		.of_match_table = ath9k_of_match_table,
 	},
-	.id_table = ath9k_platform_id_table,
 };
 
-MODULE_DEVICE_TABLE(platform, ath9k_platform_id_table);
+MODULE_DEVICE_TABLE(of, ath9k_of_match_table);
 
 int ath_ahb_init(void)
 {
Signature · 1 line
2.49.0
#4 lore raw

PATCH v2 4/5 dt-bindings: net: wireless: ath9k: add OF bindings

In reply to Rosen Penev

Now that support was added to the driver, document it.

---
 .../bindings/net/wireless/qca,ath9k.yaml      | 23 ++++++++++++++++++-
 1 file changed, 22 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml +22 -1
index 0e5412cff2bc..81d00f257922 100644
@@ -12,7 +12,7 @@ maintainers:
 description: |
   This node provides properties for configuring the ath9k wireless device.
   The node is expected to be specified as a child node of the PCI controller
-  to which the wireless chip is connected.
+  or AHB bus to which the wireless chip is connected.
 
 allOf:
   - $ref: ieee80211.yaml#
@@ -35,6 +35,12 @@ properties:
       - pci168c,0034  # AR9462
       - pci168c,0036  # AR9565
       - pci168c,0037  # AR1111 and AR9485
+      - qca,ar9130-wmac
+      - qca,ar9330-wmac
+      - qca,ar9340-wmac
+      - qca,qca9530-wmac
+      - qca,qca9550-wmac
+      - qca,qca9560-wmac
 
   reg:
     maxItems: 1
@@ -88,3 +94,18 @@ examples:
         nvmem-cell-names = "mac-address", "calibration";
       };
     };
+  - |
+    apb {
+      compatible = "simple-bus";
+      ranges;
+
+      #address-cells = <1>;
+      #size-cells = <1>;
+
+      wifi@180c0000 {
+        compatible = "qca,ar9130-wmac";
+        reg = <0x180c0000 0x230000>;
+
+        interrupts = <2>;
+      };
+    };
Signature · 1 line
2.49.0
#8 lore raw

PATCH v2 5/5 mips: dts: qca: add wmac support

In reply to Rosen Penev

Now that OF ahb support was added to the ath9k driver, we can use it to enable and use the SoC wireless found in these chipsets.

---
 arch/mips/boot/dts/qca/ar9132.dtsi                       | 9 +++++++++
 arch/mips/boot/dts/qca/ar9132_tl_wr1043nd_v1.dts         | 4 ++++
 arch/mips/boot/dts/qca/ar9331.dtsi                       | 9 +++++++++
 arch/mips/boot/dts/qca/ar9331_dpt_module.dts             | 4 ++++
 arch/mips/boot/dts/qca/ar9331_dragino_ms14.dts           | 4 ++++
 arch/mips/boot/dts/qca/ar9331_omega.dts                  | 4 ++++
 .../mips/boot/dts/qca/ar9331_openembed_som9331_board.dts | 4 ++++
 arch/mips/boot/dts/qca/ar9331_tl_mr3020.dts              | 4 ++++
 8 files changed, 42 insertions(+)
arch/mips/boot/dts/qca/ar9132.dtsi +9 -0
index aa148d51ab68..27462dc97fc5 100644
@@ -155,6 +155,15 @@ spi: spi@1f000000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
+
+		wmac: wifi@180c0000 {
+			compatible = "qca,ar9130-wmac";
+			reg = <0x180c0000 0x230000>;
+
+			interrupts = <2>;
+
+			status = "disabled";
+		};
 	};
 
 	usb_phy: usb-phy {
arch/mips/boot/dts/qca/ar9132_tl_wr1043nd_v1.dts +4 -0
index f894fe17816b..7df518fdc515 100644
@@ -108,3 +108,7 @@ partition@2 {
 		};
 	};
 };
+
+&wmac {
+	status = "okay";
+};
arch/mips/boot/dts/qca/ar9331.dtsi +9 -0
index 768ac0f869b1..bce4dcac3d54 100644
@@ -285,6 +285,15 @@ spi: spi@1f000000 {
 
 			status = "disabled";
 		};
+
+		wmac: wifi@18100000 {
+			compatible = "qca,ar9330-wmac";
+			reg = <0x18100000 0x20000>;
+
+			interrupts = <2>;
+
+			status = "disabled";
+		};
 	};
 
 	usb_phy: usb-phy {
arch/mips/boot/dts/qca/ar9331_dpt_module.dts +4 -0
index c857cd22f7db..d855dfe118e6 100644
@@ -97,3 +97,7 @@ &phy_port0 {
 &phy_port4 {
 	status = "okay";
 };
+
+&wmac {
+	status = "okay";
+};
arch/mips/boot/dts/qca/ar9331_dragino_ms14.dts +4 -0
index 7affa58d4fa6..679e793e9f55 100644
@@ -98,3 +98,7 @@ spiflash: w25q128@0 {
 		reg = <0>;
 	};
 };
+
+&wmac {
+	status = "okay";
+};
arch/mips/boot/dts/qca/ar9331_omega.dts +4 -0
index 8904aa917a6e..093142bf3ed6 100644
@@ -74,3 +74,7 @@ spiflash: w25q128@0 {
 		reg = <0>;
 	};
 };
+
+&wmac {
+	status = "okay";
+};
arch/mips/boot/dts/qca/ar9331_openembed_som9331_board.dts +4 -0
index dc65ebd60bbc..22e05d9c283a 100644
@@ -106,3 +106,7 @@ &phy_port2 {
 &phy_port4 {
 	status = "okay";
 };
+
+&wmac {
+	status = "okay";
+};
arch/mips/boot/dts/qca/ar9331_tl_mr3020.dts +4 -0
index 10b9759228b7..b740f1a91162 100644
@@ -114,3 +114,7 @@ spiflash: s25sl032p@0 {
 		reg = <0>;
 	};
 };
+
+&wmac {
+	status = "okay";
+};
Signature · 1 line
2.49.0
#5 lore raw

Re: [PATCHv2 4/5] dt-bindings: net: wireless: ath9k: add OF bindings

In reply to Rosen Penev
Quoted 1 line · Rosen Penev

Now that support was added to the driver, document it.

That's not appropriate commit msg. Binding must be before the user (see submitting patches in DT directory). Describe the hardware, what are you adding here.

Subject: OF bindings is redundant. It duplicates dt-bindings. Instead:
"Add Atheros AR9-foo-bar on AHB bus" or something similar

Missing SoB.

Please run scripts/checkpatch.pl on the patches and fix reported warnings. After that, run also 'scripts/checkpatch.pl --strict' on the patches and (probably) fix more warnings. Some warnings can be ignored, especially from --strict run, but the code here looks like it needs a fix. Feel free to get in touch if the warning is not clear.

Quoted 31 lines
---
 .../bindings/net/wireless/qca,ath9k.yaml      | 23 ++++++++++++++++++-
 1 file changed, 22 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml +7 -1
index 0e5412cff2bc..81d00f257922 100644
@@ -12,7 +12,7 @@ maintainers:
 description: |
   This node provides properties for configuring the ath9k wireless device.
   The node is expected to be specified as a child node of the PCI controller
-  to which the wireless chip is connected.
+  or AHB bus to which the wireless chip is connected.
 
 allOf:
   - $ref: ieee80211.yaml#
@@ -35,6 +35,12 @@ properties:
       - pci168c,0034  # AR9462
       - pci168c,0036  # AR9565
       - pci168c,0037  # AR1111 and AR9485
+      - qca,ar9130-wmac
+      - qca,ar9330-wmac
+      - qca,ar9340-wmac
+      - qca,qca9530-wmac
+      - qca,qca9550-wmac
+      - qca,qca9560-wmac
 
   reg:
     maxItems: 1

Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml examples: · line 101

Quoted 8 lines
Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml +5 -0
@@ -88,3 +94,18 @@ examples:
         nvmem-cell-names = "mac-address", "calibration";
       };
     };
+  - |
+    apb {
+      compatible = "simple-bus";
+      ranges;
+

Drop these two.

Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml examples: · line 103

Quoted 2 lines
Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml +2 -0
+      #address-cells = <1>;
+      #size-cells = <1>;

Best regards,
Krzysztof

#6 lore raw

Re: [PATCHv2 4/5] dt-bindings: net: wireless: ath9k: add OF bindings

Quoted 10 lines · Krzysztof Kozlowski
Quoted 1 line · Rosen Penev

Now that support was added to the driver, document it.

That's not appropriate commit msg. Binding must be before the user (see submitting patches in DT directory). Describe the hardware, what are you adding here.

Subject: OF bindings is redundant. It duplicates dt-bindings. Instead:
"Add Atheros AR9-foo-bar on AHB bus" or something similar

At this point I wonder if my approach is wrong. The other ath drivers use a qcom, prefix and a -wifi suffix. Might make sense to do the same here to avoid typing qca twice.

Quoted 58 lines

Missing SoB.

Please run scripts/checkpatch.pl on the patches and fix reported warnings. After that, run also 'scripts/checkpatch.pl --strict' on the patches and (probably) fix more warnings. Some warnings can be ignored, especially from --strict run, but the code here looks like it needs a fix. Feel free to get in touch if the warning is not clear.

Quoted 31 lines
---
 .../bindings/net/wireless/qca,ath9k.yaml      | 23 ++++++++++++++++++-
 1 file changed, 22 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml +7 -1
index 0e5412cff2bc..81d00f257922 100644
@@ -12,7 +12,7 @@ maintainers:
 description: |
   This node provides properties for configuring the ath9k wireless device.
   The node is expected to be specified as a child node of the PCI controller
-  to which the wireless chip is connected.
+  or AHB bus to which the wireless chip is connected.
 
 allOf:
   - $ref: ieee80211.yaml#
@@ -35,6 +35,12 @@ properties:
       - pci168c,0034  # AR9462
       - pci168c,0036  # AR9565
       - pci168c,0037  # AR1111 and AR9485
+      - qca,ar9130-wmac
+      - qca,ar9330-wmac
+      - qca,ar9340-wmac
+      - qca,qca9530-wmac
+      - qca,qca9550-wmac
+      - qca,qca9560-wmac
 
   reg:
     maxItems: 1

Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml examples: · line 101

Quoted 8 lines
Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml +5 -0
@@ -88,3 +94,18 @@ examples:
         nvmem-cell-names = "mac-address", "calibration";
       };
     };
+  - |
+    apb {
+      compatible = "simple-bus";
+      ranges;
+

Drop these two.

Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml examples: · line 103

Quoted 2 lines
Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml +2 -0
+      #address-cells = <1>;
+      #size-cells = <1>;

Best regards,
Krzysztof

#7 lore raw

Re: [PATCHv2 4/5] dt-bindings: net: wireless: ath9k: add OF bindings

Quoted 9 lines · Rosen Penev
Quoted 8 lines · Krzysztof Kozlowski
Quoted 1 line · Rosen Penev

Now that support was added to the driver, document it.

That's not appropriate commit msg. Binding must be before the user (see submitting patches in DT directory). Describe the hardware, what are you adding here.

Quoted 5 lines
Quoted 2 lines

Subject: OF bindings is redundant. It duplicates dt-bindings. Instead:
"Add Atheros AR9-foo-bar on AHB bus" or something similar

At this point I wonder if my approach is wrong. The other ath drivers use a qcom, prefix and a -wifi suffix. Might make sense to do the same here to avoid typing qca twice.

Yes, probably this should be qcom.

Best regards,
Krzysztof