Skip to contentSkip to conversation

arm, da85x: updates for the ipam390 board

PATCH New Heiko Schocher 2 participants 5 messages Sep 6, 2013 – Nov 4, 2013

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

v2 cover arm, da85x: updates for the ipam390 board

enable the RBL/UBL ECC layout through
CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC define

see for more info:
http://processors.wiki.ti.com/index.php/DM365_Nand_ECC_layout

and use this on the ipam390 board. Also do some minor changes for this board:

- update default environment
- change A2CR to correct value for UART boot mode
- adapt cs3cfg timings for nand
- change LED bootmode signalization

- changes for v2:
- patch: nand, davinci: add special UBL ecc position
- add comment from Scott Wood:
- move if/else/end to a more readable place

Heiko Schocher (2):
nand, davinci: add special UBL ecc position
arm, da85x: update for the ipam390 board

 board/Barix/ipam390/ipam390-ais-uart.cfg |  2 +-
 board/Barix/ipam390/ipam390.c            | 29 ++++++++------------------
 drivers/mtd/nand/davinci_nand.c          | 12 +++++++++++
 include/configs/ipam390.h                | 35 ++++++++++++++++++++------------

4 Dateien ge?ndert, 44 Zeilen hinzugef?gt(+), 34 Zeilen entfernt(-)

Signature · 1 line
1.7.11.7
#1 lore raw

PATCH v2 1/2 nand, davinci: add special UBL ecc position

enable the RBL/UBL ECC layout through
CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC define

see for more info:
http://processors.wiki.ti.com/index.php/DM365_Nand_ECC_layout

---
- changes for v2:
add comment from Scott Wood:
- move if/else/end to a more readable place

---
 drivers/mtd/nand/davinci_nand.c | 12 ++++++++++++

1 Datei ge?ndert, 12 Zeilen hinzugef?gt(+)

drivers/mtd/nand/davinci_nand.c +12 -0
index d8bb5d3..5b17d7b 100644
@@ -266,6 +266,17 @@ static int nand_davinci_correct_data(struct mtd_info *mtd, u_char *dat,
 static struct nand_ecclayout nand_davinci_4bit_layout_oobfirst = {
 #if defined(CONFIG_SYS_NAND_PAGE_2K)
 	.eccbytes = 40,
+#ifdef CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
+	.eccpos = {
+		6,   7,  8,  9, 10,	11, 12, 13, 14, 15,
+		22, 23, 24, 25, 26,	27, 28, 29, 30, 31,
+		38, 39, 40, 41, 42,	43, 44, 45, 46, 47,
+		54, 55, 56, 57, 58,	59, 60, 61, 62, 63,
+	},
+	.oobfree = {
+		{2, 4}, {16, 6}, {32, 6}, {48, 6},
+	},
+#else
 	.eccpos = {
 		24, 25, 26, 27, 28,
 		29, 30, 31, 32, 33, 34, 35, 36, 37, 38,
@@ -276,6 +287,7 @@ static struct nand_ecclayout nand_davinci_4bit_layout_oobfirst = {
 	.oobfree = {
 		{.offset = 2, .length = 22, },
 	},
+#endif	/* #ifdef CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC */
 #elif defined(CONFIG_SYS_NAND_PAGE_4K)
 	.eccbytes = 80,
 	.eccpos = {
Signature · 1 line
1.7.11.7
#2 lore raw

PATCH v2 1/2 nand, davinci: add special UBL ecc position

Quoted 9 lines · Heiko Schocher

enable the RBL/UBL ECC layout through
CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC define

see for more info:
http://processors.wiki.ti.com/index.php/DM365_Nand_ECC_layout

Applied to u-boot-ti/master, thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20131104/e86d60c3/attachment.pgp>
#3 lore raw

PATCH v2 2/2 arm, da85x: update for the ipam390 board

In reply to Heiko Schocher

- switch to correct ecc layout used by the RBL
enable CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
- update default environment
- change A2CR to correct value for UART boot mode
- adapt cs3cfg timings for nand
- change LED bootmode signalization

---
- no changes for v2

 board/Barix/ipam390/ipam390-ais-uart.cfg |  2 +-
 board/Barix/ipam390/ipam390.c            | 29 ++++++++------------------
 include/configs/ipam390.h                | 35 ++++++++++++++++++++------------

3 Dateien ge?ndert, 32 Zeilen hinzugef?gt(+), 34 Zeilen entfernt(-)

board/Barix/ipam390/ipam390-ais-uart.cfg +1 -1
index e1a99f2..709cf23 100644
@@ -109,7 +109,7 @@ CLK2XSRC = 0x00000000
 ;NANDFCR = 0x00000000
 [EMIF25ASYNC]
 A1CR = 0x00000000
-A2CR = 0x3FFFFFFE
+A2CR = 0x04202110
 A3CR = 0x00000000
 A4CR = 0x00000000
 NANDFCR = 0x00000012
board/Barix/ipam390/ipam390.c +9 -20
index f3f276e..ae88b42 100644
@@ -264,7 +264,7 @@ void show_boot_progress(int status)
 	static int green;
 
 	if (red == 0)
-		red = init_led(CONFIG_IPAM390_GPIO_LED_RED, "red", LED_OFF);
+		red = init_led(CONFIG_IPAM390_GPIO_LED_RED, "red", LED_ON);
 	if (red != CONFIG_IPAM390_GPIO_LED_RED)
 		return;
 	if (green == 0)
@@ -277,10 +277,10 @@ void show_boot_progress(int status)
 	case BOOTSTAGE_ID_RUN_OS:
 		/*
 		 * set normal state
-		 * LED Red  : off
+		 * LED Red  : on
 		 * LED green: off
 		 */
-		gpio_set_value(red, LED_OFF);
+		gpio_set_value(red, LED_ON);
 		gpio_set_value(green, LED_OFF);
 		break;
 	case BOOTSTAGE_ID_MAIN_LOOP:
@@ -326,23 +326,12 @@ int spl_start_uboot(void)
 	if (!bootmode)
 		if (ret == 0)
 			bootmode = 1;
-	if (bootmode) {
-		/*
-		 * Booting U-Boot
-		 * LED Red  : on
-		 * LED green: off
-		 */
-		init_led(CONFIG_IPAM390_GPIO_LED_RED, "red", LED_ON);
-		init_led(CONFIG_IPAM390_GPIO_LED_GREEN, "green", LED_OFF);
-	} else {
-		/*
-		 * Booting Linux
-		 * LED Red  : off
-		 * LED green: off
-		 */
-		init_led(CONFIG_IPAM390_GPIO_LED_RED, "red", LED_OFF);
-		init_led(CONFIG_IPAM390_GPIO_LED_GREEN, "green", LED_OFF);
-	}
+	/*
+	 * LED red  : on
+	 * LED green: off
+	 */
+	init_led(CONFIG_IPAM390_GPIO_LED_RED, "red", LED_ON);
+	init_led(CONFIG_IPAM390_GPIO_LED_GREEN, "green", LED_OFF);
 	return bootmode;
 }
 #endif
include/configs/ipam390.h +22 -13
index 82d4298..155663e 100644
@@ -122,13 +122,13 @@
 	(3 << DV_DDR_SDCR_IBANK_SHIFT) |	\
 	(2 << DV_DDR_SDCR_PAGESIZE_SHIFT))
 
-#define CONFIG_SYS_DA850_CS3CFG	(DAVINCI_ABCR_WSETUP(2)	| \
+#define CONFIG_SYS_DA850_CS3CFG	(DAVINCI_ABCR_WSETUP(1)	| \
 				DAVINCI_ABCR_WSTROBE(2)	| \
-				DAVINCI_ABCR_WHOLD(1)	| \
+				DAVINCI_ABCR_WHOLD(0)	| \
 				DAVINCI_ABCR_RSETUP(1)	| \
-				DAVINCI_ABCR_RSTROBE(4)	| \
-				DAVINCI_ABCR_RHOLD(0)	| \
-				DAVINCI_ABCR_TA(1)	| \
+				DAVINCI_ABCR_RSTROBE(2)	| \
+				DAVINCI_ABCR_RHOLD(1)	| \
+				DAVINCI_ABCR_TA(0)	| \
 				DAVINCI_ABCR_ASIZE_8BIT)
 
 
@@ -161,6 +161,7 @@
 #undef CONFIG_SYS_NAND_HW_ECC
 #define CONFIG_SYS_MAX_NAND_DEVICE	1 /* Max number of NAND devices */
 #define CONFIG_SYS_NAND_HW_ECC_OOBFIRST
+#define CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 #define CONFIG_SYS_NAND_PAGE_SIZE	(2 << 10)
 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128 << 10)
@@ -173,11 +174,10 @@
 					CONFIG_SYS_MALLOC_LEN -       \
 					GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_NAND_ECCPOS		{				\
-				24, 25, 26, 27, 28, \
-				29, 30, 31, 32, 33, 34, 35, 36, 37, 38, \
-				39, 40, 41, 42, 43, 44, 45, 46, 47, 48, \
-				49, 50, 51, 52, 53, 54, 55, 56, 57, 58, \
-				59, 60, 61, 62, 63 }
+			6,   7,  8,  9, 10,	11, 12, 13, 14, 15,	\
+			22, 23, 24, 25, 26,	27, 28, 29, 30, 31,	\
+			38, 39, 40, 41, 42,	43, 44, 45, 46, 47,	\
+			54, 55, 56, 57, 58,	59, 60, 61, 62, 63}
 #define CONFIG_SYS_NAND_PAGE_COUNT	64
 #define CONFIG_SYS_NAND_BAD_BLOCK_POS	0
 #define CONFIG_SYS_NAND_ECCSIZE		512
@@ -230,15 +230,24 @@
 #define CONFIG_CMDLINE_TAG
 #define CONFIG_REVISION_TAG
 #define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_BOOTARGS		\
-	"mem=128M console=ttyS0,115200n8 root=/dev/mtdblock0p4 rw noinitrd ip=dhcp"
-#define CONFIG_BOOTDELAY	3
+#define CONFIG_BOOTDELAY	2
 #define CONFIG_EXTRA_ENV_SETTINGS \
+	"defbootargs=setenv bootargs mem=128M console=ttyS0,115200n8 " \
+		"root=/dev/mtdblock5 rw noinitrd " \
+		"rootfstype=jffs2 noinitrd\0" \
 	"hwconfig=dsp:wake=yes\0" \
+	"bootcmd=nboot kernel;run defbootargs addmtd;bootm 0xc0700000\0" \
+	"bootfile=uImage\0" \
 	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"	\
+	"mtddevname=uboot-env\0" \
+	"mtddevnum=0\0" \
 	"mtdids=" MTDIDS_DEFAULT "\0"				\
 	"mtdparts=" MTDPARTS_DEFAULT "\0"			\
+	"u-boot=/tftpboot/ipam390/u-boot.ais\0"			\
+	"upd_uboot=tftp c0000000 ${u-boot};nand erase.part u-boot;" \
+		"nand write c0000000 20000 ${filesize}\0"	\
 	"setbootparms=nand read c0100000 200000 400000;"	\
+		"run defbootargs addmtd;"			\
 		"spl export atags c0100000;"			\
 		"nand erase.part bootparms;"			\
 		"nand write c0000100 180000 20000\0"		\
Signature · 1 line
1.7.11.7
#4 lore raw

PATCH v2 2/2 arm, da85x: update for the ipam390 board

Quoted 9 lines · Heiko Schocher

- switch to correct ecc layout used by the RBL
enable CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
- update default environment
- change A2CR to correct value for UART boot mode
- adapt cs3cfg timings for nand
- change LED bootmode signalization

Applied to u-boot-ti/master, thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20131104/f1ad9ee4/attachment.pgp>