arm, da85x: updates for the ipam390 board
Subsystems (2)
v2 cover arm, da85x: updates for the ipam390 board
enable the RBL/UBL ECC layout throughCONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC define
see for more info:
http://processors.wiki.ti.com/index.php/DM365_Nand_ECC_layout
and use this on the ipam390 board. Also do some minor changes for this board:
- update default environment
- change A2CR to correct value for UART boot mode
- adapt cs3cfg timings for nand
- change LED bootmode signalization
- changes for v2:
- patch: nand, davinci: add special UBL ecc position
- add comment from Scott Wood:
- move if/else/end to a more readable place
Heiko Schocher (2):
nand, davinci: add special UBL ecc position
arm, da85x: update for the ipam390 board
board/Barix/ipam390/ipam390-ais-uart.cfg | 2 +- board/Barix/ipam390/ipam390.c | 29 ++++++++------------------ drivers/mtd/nand/davinci_nand.c | 12 +++++++++++ include/configs/ipam390.h | 35 ++++++++++++++++++++------------
4 Dateien ge?ndert, 44 Zeilen hinzugef?gt(+), 34 Zeilen entfernt(-)
Signature · 1 line
1.7.11.7
PATCH v2 1/2 nand, davinci: add special UBL ecc position
enable the RBL/UBL ECC layout throughCONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC define
see for more info:
http://processors.wiki.ti.com/index.php/DM365_Nand_ECC_layout
---
- changes for v2:
add comment from Scott Wood:
- move if/else/end to a more readable place
--- drivers/mtd/nand/davinci_nand.c | 12 ++++++++++++
1 Datei ge?ndert, 12 Zeilen hinzugef?gt(+)
drivers/mtd/nand/davinci_nand.c +12 -0
@@ -266,6 +266,17 @@ static int nand_davinci_correct_data(struct mtd_info *mtd, u_char *dat, static struct nand_ecclayout nand_davinci_4bit_layout_oobfirst = { #if defined(CONFIG_SYS_NAND_PAGE_2K) .eccbytes = 40, +#ifdef CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC + .eccpos = { + 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, + 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, + 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, + 54, 55, 56, 57, 58, 59, 60, 61, 62, 63, + }, + .oobfree = { + {2, 4}, {16, 6}, {32, 6}, {48, 6}, + }, +#else .eccpos = { 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38,
@@ -276,6 +287,7 @@ static struct nand_ecclayout nand_davinci_4bit_layout_oobfirst = { .oobfree = { {.offset = 2, .length = 22, }, }, +#endif /* #ifdef CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC */ #elif defined(CONFIG_SYS_NAND_PAGE_4K) .eccbytes = 80, .eccpos = {
Signature · 1 line
1.7.11.7
PATCH v2 1/2 nand, davinci: add special UBL ecc position
Quoted 9 lines · Heiko Schocher
enable the RBL/UBL ECC layout through
CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECCdefinesee for more info:
http://processors.wiki.ti.com/index.php/DM365_Nand_ECC_layoutSigned-off-by Heiko Schocher <[email protected]>Cc Tom Rini <[email protected]>Cc Scott Wood <[email protected]>
Applied to u-boot-ti/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20131104/e86d60c3/attachment.pgp>
PATCH v2 2/2 arm, da85x: update for the ipam390 board
In reply to Heiko Schocher- switch to correct ecc layout used by the RBL
enable CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
- update default environment
- change A2CR to correct value for UART boot mode
- adapt cs3cfg timings for nand
- change LED bootmode signalization
---
- no changes for v2
board/Barix/ipam390/ipam390-ais-uart.cfg | 2 +- board/Barix/ipam390/ipam390.c | 29 ++++++++------------------ include/configs/ipam390.h | 35 ++++++++++++++++++++------------
3 Dateien ge?ndert, 32 Zeilen hinzugef?gt(+), 34 Zeilen entfernt(-)
board/Barix/ipam390/ipam390-ais-uart.cfg +1 -1
@@ -109,7 +109,7 @@ CLK2XSRC = 0x00000000 ;NANDFCR = 0x00000000 [EMIF25ASYNC] A1CR = 0x00000000 -A2CR = 0x3FFFFFFE +A2CR = 0x04202110 A3CR = 0x00000000 A4CR = 0x00000000 NANDFCR = 0x00000012
board/Barix/ipam390/ipam390.c +9 -20
@@ -264,7 +264,7 @@ void show_boot_progress(int status)static int green;if (red ==0 ) - red =init_led (CONFIG_IPAM390_GPIO_LED_RED ,"red" ,LED_OFF ); + red =init_led (CONFIG_IPAM390_GPIO_LED_RED ,"red" ,LED_ON );if (red !=CONFIG_IPAM390_GPIO_LED_RED )return ;if (green ==0 )
@@ -277,10 +277,10 @@ void show_boot_progress(int status)case BOOTSTAGE_ID_RUN_OS :/* * set normal state -* LED Red : off +* LED Red : on * LED green: off */ -gpio_set_value (red,LED_OFF ); +gpio_set_value (red,LED_ON );gpio_set_value (green,LED_OFF );break ;case BOOTSTAGE_ID_MAIN_LOOP :
@@ -326,23 +326,12 @@ int spl_start_uboot(void)if (!bootmode)if (ret ==0 ) bootmode =1 ; -if (bootmode) { -/* -* Booting U-Boot -* LED Red : on -* LED green: off -*/ -init_led (CONFIG_IPAM390_GPIO_LED_RED ,"red" ,LED_ON ); -init_led (CONFIG_IPAM390_GPIO_LED_GREEN ,"green" ,LED_OFF ); - }else { -/* -* Booting Linux -* LED Red : off -* LED green: off -*/ -init_led (CONFIG_IPAM390_GPIO_LED_RED ,"red" ,LED_OFF ); -init_led (CONFIG_IPAM390_GPIO_LED_GREEN ,"green" ,LED_OFF ); - } +/* +* LED red : on +* LED green: off +*/ +init_led (CONFIG_IPAM390_GPIO_LED_RED ,"red" ,LED_ON ); +init_led (CONFIG_IPAM390_GPIO_LED_GREEN ,"green" ,LED_OFF ); return bootmode; }#endif
include/configs/ipam390.h +22 -13
@@ -122,13 +122,13 @@ (3 << DV_DDR_SDCR_IBANK_SHIFT) | \ (2 << DV_DDR_SDCR_PAGESIZE_SHIFT)) -#define CONFIG_SYS_DA850_CS3CFG (DAVINCI_ABCR_WSETUP(2) | \ +#define CONFIG_SYS_DA850_CS3CFG (DAVINCI_ABCR_WSETUP(1) | \ DAVINCI_ABCR_WSTROBE(2) | \ - DAVINCI_ABCR_WHOLD(1) | \ + DAVINCI_ABCR_WHOLD(0) | \ DAVINCI_ABCR_RSETUP(1) | \ - DAVINCI_ABCR_RSTROBE(4) | \ - DAVINCI_ABCR_RHOLD(0) | \ - DAVINCI_ABCR_TA(1) | \ + DAVINCI_ABCR_RSTROBE(2) | \ + DAVINCI_ABCR_RHOLD(1) | \ + DAVINCI_ABCR_TA(0) | \ DAVINCI_ABCR_ASIZE_8BIT)
@@ -161,6 +161,7 @@#undef CONFIG_SYS_NAND_HW_ECC#define CONFIG_SYS_MAX_NAND_DEVICE 1/* Max number of NAND devices */ #define CONFIG_SYS_NAND_HW_ECC_OOBFIRST +#define CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC #define CONFIG_SYS_NAND_5_ADDR_CYCLE #define CONFIG_SYS_NAND_PAGE_SIZE (2 << 10)#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10)
@@ -173,11 +174,10 @@ CONFIG_SYS_MALLOC_LEN - \ GENERATED_GBL_DATA_SIZE)#define CONFIG_SYS_NAND_ECCPOS { \ - 24, 25, 26, 27, 28, \ - 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, \ - 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, \ - 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, \ - 59, 60, 61, 62, 63 } + 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, \ + 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, \ + 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, \ + 54, 55, 56, 57, 58, 59, 60, 61, 62, 63}#define CONFIG_SYS_NAND_PAGE_COUNT 64#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0#define CONFIG_SYS_NAND_ECCSIZE 512
@@ -230,15 +230,24 @@#define CONFIG_CMDLINE_TAG #define CONFIG_REVISION_TAG #define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_BOOTARGS \ - "mem=128M console=ttyS0,115200n8 root=/dev/mtdblock0p4 rw noinitrd ip=dhcp" -#define CONFIG_BOOTDELAY 3 +#define CONFIG_BOOTDELAY 2#define CONFIG_EXTRA_ENV_SETTINGS \ + "defbootargs=setenv bootargs mem=128M console=ttyS0,115200n8 " \ + "root=/dev/mtdblock5 rw noinitrd " \ + "rootfstype=jffs2 noinitrd\0" \ "hwconfig=dsp:wake=yes\0" \ + "bootcmd=nboot kernel;run defbootargs addmtd;bootm 0xc0700000\0" \ + "bootfile=uImage\0" \ "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ + "mtddevname=uboot-env\0" \ + "mtddevnum=0\0" \ "mtdids=" MTDIDS_DEFAULT "\0" \ "mtdparts=" MTDPARTS_DEFAULT "\0" \ + "u-boot=/tftpboot/ipam390/u-boot.ais\0" \ + "upd_uboot=tftp c0000000 ${u-boot};nand erase.part u-boot;" \ + "nand write c0000000 20000 ${filesize}\0" \ "setbootparms=nand read c0100000 200000 400000;" \ + "run defbootargs addmtd;" \ "spl export atags c0100000;" \ "nand erase.part bootparms;" \ "nand write c0000100 180000 20000\0" \
Signature · 1 line
1.7.11.7
PATCH v2 2/2 arm, da85x: update for the ipam390 board
Quoted 9 lines · Heiko Schocher
- switch to correct ecc layout used by the RBL
enableCONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
- update default environment
- change A2CR to correct value for UART boot mode
- adapt cs3cfg timings for nand
- change LED bootmode signalizationSigned-off-by Heiko Schocher <[email protected]>Cc Tom Rini <[email protected]>
Applied to u-boot-ti/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20131104/f1ad9ee4/attachment.pgp>