board: atmel: sama5d2_icp: add periph reset in SPL hw init
PATCH 1/3 board: atmel: sama5d2_icp: add periph reset in SPL hw init
From: Eugen Hristev <[email protected]>
Some periphs on the board need to be reset by holding their reset GPIO down for a specific time period.
On a warm reset, the periphs are not being reset by any reset pin and may be in a wrong state.
Reset them in the SPL to make sure we are booting into the correct state machine of the specific board periphs (KSZ eth switch, USB hub, HSIC eth, Ethercat)
--- board/atmel/sama5d2_icp/sama5d2_icp.c | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+)
board/atmel/sama5d2_icp/sama5d2_icp.c +23 -0
@@ -73,6 +73,23 @@ int misc_init_r(void)/* SPL */ #ifdef CONFIG_SPL_BUILD +/* deassert reset lines for external periph in case of warm reboot */ +static void board_reset_additional_periph(void) +{ + atmel_pio4_set_pio_output(AT91_PIO_PORTB, 16, 0); /* LAN9252_RST */ + atmel_pio4_set_pio_output(AT91_PIO_PORTC, 2, 0); /* HSIC_RST */ + atmel_pio4_set_pio_output(AT91_PIO_PORTC, 17, 0); /* USB2534_RST */ + atmel_pio4_set_pio_output(AT91_PIO_PORTD, 4, 0); /* KSZ8563_RST */ +} + +static void board_start_additional_periph(void) +{ + atmel_pio4_set_pio_output(AT91_PIO_PORTB, 16, 1); /* LAN9252_RST */ + atmel_pio4_set_pio_output(AT91_PIO_PORTC, 2, 1); /* HSIC_RST */ + atmel_pio4_set_pio_output(AT91_PIO_PORTC, 17, 1); /* USB2534_RST */ + atmel_pio4_set_pio_output(AT91_PIO_PORTD, 4, 1); /* KSZ8563_RST */ +} + #ifdef CONFIG_SD_BOOT void spl_mmc_init(void) {
@@ -93,12 +110,18 @@ void spl_board_init(void)#ifdef CONFIG_SD_BOOT spl_mmc_init ();#endif +board_reset_additional_periph (); }void spl_display_print (void ) { } +void spl_board_prepare_for_boot (void ) +{ +board_start_additional_periph (); +} +static void ddrc_conf (struct atmel_mpddrc_config *ddrc) { ddrc->md = (ATMEL_MPDDRC_MD_DBW_32_BITS |ATMEL_MPDDRC_MD_DDR3_SDRAM );
Signature · 1 line
2.7.4
PATCH 1/3 board: atmel: sama5d2_icp: add periph reset in SPL hw init
Quoted 10 lines · On 08.05.2019 15:58, Eugen Hristev - M18282 wrote:
From: Eugen Hristev <[email protected]>
Some periphs on the board need to be reset by holding their reset GPIO down for a specific time period.
On a warm reset, the periphs are not being reset by any reset pin and may be in a wrong state.
Reset them in the SPL to make sure we are booting into the correct state machine of the specific board periphs (KSZ eth switch, USB hub, HSIC eth, Ethercat)
Quoted 2 lines
Signed-off-by Eugen Hristev <[email protected]>---
Applied all 3 patches to u-boot-atmel/master
PATCH 2/3 board: atmel: sama5d2_icp: standby disable on CAN transceivers in SPL
In reply to Eugen.Hristev at microchip.comFrom: Eugen Hristev <[email protected]>
The 2 CAN transceivers have a STBDY pin which must be low in order to operate.
This pin is tied to PB25.
Set it to 0 in bootstrap.
At a later time, this needs to be controlled by Linux power management system, or requested by some driver as a gpio and tied to 0 during CAN link up.
--- board/atmel/sama5d2_icp/sama5d2_icp.c | 7 +++++++ 1 file changed, 7 insertions(+)
board/atmel/sama5d2_icp/sama5d2_icp.c +7 -0
@@ -73,6 +73,12 @@ int misc_init_r(void)/* SPL */ #ifdef CONFIG_SPL_BUILD +/* must set PB25 low to enable the CAN transceivers */ +static void board_can_stdby_dis (void ) +{ +atmel_pio4_set_pio_output (AT91_PIO_PORTB ,25 ,0 ); +} +/* deassert reset lines for external periph in case of warm reboot */ static void board_reset_additional_periph (void ) {
@@ -111,6 +117,7 @@ void spl_board_init(void)spl_mmc_init ();#endif board_reset_additional_periph (); +board_can_stdby_dis (); }void spl_display_print (void )
Signature · 1 line
2.7.4
PATCH 3/3 board: atmel: sama5d2_icp: enable green led on SPL completion
In reply to Eugen.Hristev at microchip.comFrom: Eugen Hristev <[email protected]>
Enable the green led on SPL completion.
Red led has no pulldown and it will be lighted by default when the board starts up.
If the PMIC is not configured to enable LDO2, the leds will not light.
--- board/atmel/sama5d2_icp/sama5d2_icp.c | 8 ++++++++ 1 file changed, 8 insertions(+)
board/atmel/sama5d2_icp/sama5d2_icp.c +8 -0
@@ -79,6 +79,13 @@ static void board_can_stdby_dis(void)atmel_pio4_set_pio_output (AT91_PIO_PORTB ,25 ,0 ); } +static void board_leds_init (void ) +{ +atmel_pio4_set_pio_output (AT91_PIO_PORTB ,0 ,0 );/* RED */ +atmel_pio4_set_pio_output (AT91_PIO_PORTB ,1 ,1 );/* GREEN */ +atmel_pio4_set_pio_output (AT91_PIO_PORTA ,31 ,0 );/* BLUE */ +} +/* deassert reset lines for external periph in case of warm reboot */ static void board_reset_additional_periph (void ) {
@@ -118,6 +125,7 @@ void spl_board_init(void)#endif board_reset_additional_periph ();board_can_stdby_dis (); +board_leds_init (); }void spl_display_print (void )
Signature · 1 line
2.7.4