Skip to contentSkip to conversation

power: Add AVS class 0 support for AM6

PATCH Superseded Keerthy 3 participants 14 messages Oct 14, 2019 – Oct 21, 2019

Subsystems (3)

v1 of 3 Superseded Latest is v3 →

lore
Share & tools
lore

Keerthy

author
#0 lore raw

cover power: Add AVS class 0 support for AM6

Adaptive Voltage Scaling is a technology used in TI SoCs to optimize the operating voltage based on characterization data written to efuse during production.

Add support for Adaptive Voltage scaling class 0 support for AM6 family of devices. Adaptive voltage scaling class 0 implies that optimized voltage values for a particular OPP of a particular voltage domain are read from Efuse and programmed on the pmic/regulator.

Tested on AM654-EVM for MPU @800 MHz.

Keerthy (2):
arm: mach-k3: am6_init: Initialize AVS class 0
clk: clk-ti-sci: Notify AVS driver upon setting clock rate

Tero Kristo (8):
power: add driver for K3 Adaptive Voltage Scaling Class 0
power: regulator: tps6236x: add support for tps6236x regulators
arm: dts: k3-am65: Add VTM node
arm: dts: k3-am654-r5-base-board: enable wkup_i2c0 driver for spl
arm: dts: k3-am654-r5-base-board: add supply rail for MPU
arm: dts: k3-am654-r5-base-board: enable wkup_vtm0 node and link in
supplies
configs: am65x_evm_r5_defconfig: Enable TPS62363 regulator support
configs: am65x_evm_r5_defconfig: Enable AVS class 0 support

 arch/arm/dts/k3-am65-wakeup.dtsi             |   7 +
 arch/arm/dts/k3-am654-r5-base-board.dts      |  20 +
 arch/arm/mach-k3/am6_init.c                  |   6 +
 configs/am65x_evm_r5_defconfig               |   2 +
 drivers/Makefile                             |   2 +-
 drivers/clk/clk-ti-sci.c                     |   5 +
 drivers/power/Kconfig                        |   9 +
 drivers/power/mfd/Makefile                   |   1 +
 drivers/power/mfd/k3_avs.c                   | 371 +++++++++++++++++++
 drivers/power/regulator/Kconfig              |  10 +
 drivers/power/regulator/Makefile             |   1 +
 drivers/power/regulator/tps62360_regulator.c | 124 +++++++
 include/dm/uclass-id.h                       |   1 +
 include/k3-avs.h                             |  28 ++
 14 files changed, 586 insertions(+), 1 deletion(-)
 create mode 100644 drivers/power/mfd/k3_avs.c
 create mode 100644 drivers/power/regulator/tps62360_regulator.c
 create mode 100644 include/k3-avs.h
Signature · 1 line
2.17.1
author
#1 lore raw

PATCH 1/10 power: add driver for K3 Adaptive Voltage Scaling Class 0

From: Tero Kristo <[email protected]>

Adaptive Voltage Scaling is a technology used in TI SoCs to optimize the operating voltage based on characterization data written to efuse during production. Add a driver to support this feature for K3 line of SoCs, initially for AM65x.

---
 drivers/Makefile           |   2 +-
 drivers/power/Kconfig      |   9 +
 drivers/power/mfd/Makefile |   1 +
 drivers/power/mfd/k3_avs.c | 371 +++++++++++++++++++++++++++++++++++++
 include/dm/uclass-id.h     |   1 +
 include/k3-avs.h           |  28 +++
 6 files changed, 411 insertions(+), 1 deletion(-)
 create mode 100644 drivers/power/mfd/k3_avs.c
 create mode 100644 include/k3-avs.h
drivers/Makefile +1 -1
index a4bb5e4975..4e2de903d3 100644
@@ -38,7 +38,7 @@ obj-$(CONFIG_ARMADA_38X) += ddr/marvell/a38x/
 obj-$(CONFIG_ARMADA_XP) += ddr/marvell/axp/
 obj-$(CONFIG_$(SPL_)ALTERA_SDRAM) += ddr/altera/
 obj-$(CONFIG_ARCH_IMX8M) += ddr/imx/imx8m/
-obj-$(CONFIG_SPL_POWER_SUPPORT) += power/ power/pmic/
+obj-$(CONFIG_SPL_POWER_SUPPORT) += power/ power/pmic/ power/mfd/
 obj-$(CONFIG_SPL_POWER_SUPPORT) += power/regulator/
 obj-$(CONFIG_SPL_POWER_DOMAIN) += power/domain/
 obj-$(CONFIG_SPL_DM_RESET) += reset/
drivers/power/Kconfig +9 -0
index 9495dca33b..8e1c957e22 100644
@@ -364,4 +364,13 @@ config TWL4030_POWER
 	The TWL4030 in a combination audio CODEC/power management with
 	GPIO and it is commonly used with the OMAP3 family of processors
 
+config K3_AVS0
+	depends on ARCH_K3 && SPL_DM_REGULATOR
+	bool "AVS class 0 support for K3 devices"
+	help
+	K3 devices have the optimized voltage values for the main voltage
+	domains stored in efuse within the VTM IP. This driver reads the
+	optimized voltage from the efuse, so that it can be programmed
+	to the PMIC on board.
+
 endmenu
drivers/power/mfd/Makefile +1 -0
index a8eb7f81e7..54caed3f9c 100644
@@ -6,3 +6,4 @@
 obj-$(CONFIG_POWER_PMIC_MAX77693) += pmic_max77693.o
 obj-$(CONFIG_POWER_MUIC_MAX77693) += muic_max77693.o
 obj-$(CONFIG_POWER_FG_MAX77693) += fg_max77693.o
+obj-$(CONFIG_K3_AVS0) += k3_avs.o
drivers/power/mfd/k3_avs.c new file +371 -0

371 lines not on this page · raw message

include/dm/uclass-id.h +1 -0
index f431f3bf29..605b52905e 100644
@@ -31,6 +31,7 @@ enum uclass_id {
 	UCLASS_ADC,		/* Analog-to-digital converter */
 	UCLASS_AHCI,		/* SATA disk controller */
 	UCLASS_AUDIO_CODEC,	/* Audio codec with control and data path */
+	UCLASS_AVS,		/* Adaptive voltage scaling */
 	UCLASS_AXI,		/* AXI bus */
 	UCLASS_BLK,		/* Block device */
 	UCLASS_BOARD,		/* Device information from hardware */
include/k3-avs.h new file +28 -0
new file mode 100644
index 0000000000..9867481617
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Texas Instruments' K3 Adaptive Voltage Scaling driver
+ *
+ * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+ *      Tero Kristo <[email protected]>
+ *
+ */
+
+#ifndef _K3_AVS0_
+#define _K3_AVS0_
+
+#define AM6_VDD_WKUP		0
+#define AM6_VDD_MCU		1
+#define AM6_VDD_CORE		2
+#define AM6_VDD_MPU0		3
+#define AM6_VDD_MPU1		4
+
+#define NUM_OPPS		4
+
+#define AM6_OPP_NOM		1
+#define AM6_OPP_OD		2
+#define AM6_OPP_TURBO		3
+
+int k3_avs_set_opp(struct udevice *dev, int vdd_id, int opp_id);
+int k3_avs_notify_freq(int dev_id, int clk_id, u32 freq);
+
+#endif
Signature · 1 line
2.17.1
#2 lore raw

PATCH 1/10 power: add driver for K3 Adaptive Voltage Scaling Class 0

[..snip..]

include/dm/uclass-id.h enum uclass_id { · line 34

Quoted 10 lines
(quoted diff) +1 -0
+};
include/dm/uclass-id.h +1 -0
index f431f3bf29..605b52905e 100644
@@ -31,6 +31,7 @@ enum uclass_id {
 	UCLASS_ADC,		/* Analog-to-digital converter */
 	UCLASS_AHCI,		/* SATA disk controller */
 	UCLASS_AUDIO_CODEC,	/* Audio codec with control and data path */
+	UCLASS_AVS,		/* Adaptive voltage scaling */

In general there should be sandbox tests written for adding any such new UCLASS.

Thanks and regards,
Lokesh

Quoted 38 lines
include/dm/uclass-id.h +0 -0
 	UCLASS_AXI,		/* AXI bus */
 	UCLASS_BLK,		/* Block device */
 	UCLASS_BOARD,		/* Device information from hardware */
include/k3-avs.h new file +28 -0
new file mode 100644
index 0000000000..9867481617
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Texas Instruments' K3 Adaptive Voltage Scaling driver
+ *
+ * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+ *      Tero Kristo <[email protected]>
+ *
+ */
+
+#ifndef _K3_AVS0_
+#define _K3_AVS0_
+
+#define AM6_VDD_WKUP		0
+#define AM6_VDD_MCU		1
+#define AM6_VDD_CORE		2
+#define AM6_VDD_MPU0		3
+#define AM6_VDD_MPU1		4
+
+#define NUM_OPPS		4
+
+#define AM6_OPP_NOM		1
+#define AM6_OPP_OD		2
+#define AM6_OPP_TURBO		3
+
+int k3_avs_set_opp(struct udevice *dev, int vdd_id, int opp_id);
+int k3_avs_notify_freq(int dev_id, int clk_id, u32 freq);
+
+#endif
author
#3 lore raw

PATCH 1/10 power: add driver for K3 Adaptive Voltage Scaling Class 0

Quoted 15 lines · Lokesh Vutla

[..snip..]

include/dm/uclass-id.h enum uclass_id { · line 34

Quoted 10 lines
(quoted diff) +1 -0
+};
include/dm/uclass-id.h +1 -0
index f431f3bf29..605b52905e 100644
@@ -31,6 +31,7 @@ enum uclass_id {
  	UCLASS_ADC,		/* Analog-to-digital converter */
  	UCLASS_AHCI,		/* SATA disk controller */
  	UCLASS_AUDIO_CODEC,	/* Audio codec with control and data path */
+	UCLASS_AVS,		/* Adaptive voltage scaling */

In general there should be sandbox tests written for adding any such new UCLASS.

Tero,

This is not a generic UCLASS driver. This is a K3 specific driver. So should this be really introducing a new UCLASS?

- Keerthy

Quoted 42 lines

Thanks and regards,
Lokesh

Quoted 38 lines
include/dm/uclass-id.h +0 -0
  	UCLASS_AXI,		/* AXI bus */
  	UCLASS_BLK,		/* Block device */
  	UCLASS_BOARD,		/* Device information from hardware */
include/k3-avs.h new file +28 -0
new file mode 100644
index 0000000000..9867481617
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Texas Instruments' K3 Adaptive Voltage Scaling driver
+ *
+ * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+ *      Tero Kristo <[email protected]>
+ *
+ */
+
+#ifndef _K3_AVS0_
+#define _K3_AVS0_
+
+#define AM6_VDD_WKUP		0
+#define AM6_VDD_MCU		1
+#define AM6_VDD_CORE		2
+#define AM6_VDD_MPU0		3
+#define AM6_VDD_MPU1		4
+
+#define NUM_OPPS		4
+
+#define AM6_OPP_NOM		1
+#define AM6_OPP_OD		2
+#define AM6_OPP_TURBO		3
+
+int k3_avs_set_opp(struct udevice *dev, int vdd_id, int opp_id);
+int k3_avs_notify_freq(int dev_id, int clk_id, u32 freq);
+
+#endif
#4 lore raw

PATCH 1/10 power: add driver for K3 Adaptive Voltage Scaling Class 0

Quoted 21 lines · Keerthy
Quoted 17 lines · Lokesh Vutla

[..snip..]

Quoted 11 lines
(quoted diff) +1 -0
+};
include/dm/uclass-id.h +0 -0
index f431f3bf29..605b52905e 100644
@@ -31,6 +31,7 @@ enum uclass_id {

      UCLASS_ADC,        /* Analog-to-digital converter */ UCLASS_AHCI,        /* SATA disk controller */ UCLASS_AUDIO_CODEC,    /* Audio codec with control and data path */
+    UCLASS_AVS,        /* Adaptive voltage scaling */

In general there should be sandbox tests written for adding any such new UCLASS.

Quoted 4 lines

Tero,

This is not a generic UCLASS driver. This is a K3 specific driver. So should this be really introducing a new UCLASS?

Well, AVS is kind of generic across TI SoCs. However, I am fine just using UCLASS_MISC if we don't want to introduce a new uclass.... assuming we don't get sequencing issues with remoteproc if we do that.

-Tero

Quoted 38 lines

- Keerthy

Quoted 35 lines

Thanks and regards,
Lokesh

Quoted 31 lines

      UCLASS_AXI,        /* AXI bus */
      UCLASS_BLK,        /* Block device */ UCLASS_BOARD,        /* Device information from hardware */

include/k3-avs.h new file +5 -0
new file mode 100644
index 0000000000..9867481617
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Texas Instruments' K3 Adaptive Voltage Scaling driver
+ *
+ * Copyright (C) 2019 Texas Instruments Incorporated - 

http://www.ti.com/
+ *      Tero Kristo <[email protected]>
+ *
+ */

include/k3-avs.h new file +13 -0
+
+#ifndef _K3_AVS0_
+#define _K3_AVS0_
+
+#define AM6_VDD_WKUP        0
+#define AM6_VDD_MCU        1
+#define AM6_VDD_CORE        2
+#define AM6_VDD_MPU0        3
+#define AM6_VDD_MPU1        4
+
+#define NUM_OPPS        4
+
+#define AM6_OPP_NOM        1
Quoted 8 lines
Quoted 8 lines

include/k3-avs.h line 28

Quoted 8 lines
include/k3-avs.h new file +7 -0
+#define AM6_OPP_OD        2
+#define AM6_OPP_TURBO        3
+
+int k3_avs_set_opp(struct udevice *dev, int vdd_id, int opp_id);
+int k3_avs_notify_freq(int dev_id, int clk_id, u32 freq);
+
+#endif

--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki

author
#5 lore raw

PATCH 2/10 arm: mach-k3: am6_init: Initialize AVS class 0

In reply to Keerthy

Initialize AVS class 0 so that mpu voltage rail is programmed to the AVS class 0 compensated value.

---
 arch/arm/mach-k3/am6_init.c | 6 ++++++
 1 file changed, 6 insertions(+)
arch/arm/mach-k3/am6_init.c +6 -0
index 0b564f7bd1..86395a72b9 100644
@@ -116,6 +116,12 @@ void board_init_f(ulong dummy)
 	/* Perform EEPROM-based board detection */
 	do_board_detect();
 
+#if defined(CONFIG_CPU_V7R) && defined(CONFIG_K3_AVS0)
+	ret = uclass_get_device(UCLASS_AVS, 0, &dev);
+	if (ret)
+		printf("AVS init failed: %d\n", ret);
+#endif
+
 #ifdef CONFIG_K3_AM654_DDRSS
 	ret = uclass_get_device(UCLASS_RAM, 0, &dev);
 	if (ret)
Signature · 1 line
2.17.1
author
#6 lore raw

PATCH 3/10 clk: clk-ti-sci: Notify AVS driver upon setting clock rate

In reply to Keerthy

Notify AVS driver upon setting clock rate so that voltage is changed accordingly.

---
 drivers/clk/clk-ti-sci.c | 5 +++++
 1 file changed, 5 insertions(+)
drivers/clk/clk-ti-sci.c +5 -0
index c25415d410..478349f22f 100644
@@ -13,6 +13,7 @@
 #include <errno.h>
 #include <clk-uclass.h>
 #include <linux/soc/ti/ti_sci_protocol.h>
+#include <k3-avs.h>
 
 /**
  * struct ti_sci_clk_data - clock controller information structure
@@ -101,6 +102,10 @@ static ulong ti_sci_clk_set_rate(struct clk *clk, ulong rate)
 
 	debug("%s(clk=%p, rate=%lu)\n", __func__, clk, rate);
 
+#ifdef CONFIG_K3_AVS0
+	k3_avs_notify_freq(clk->id, clk->data, rate);
+#endif
+
 	/* Ask for exact frequency by using same value for min/target/max */
 	ret = cops->set_freq(sci, clk->id, clk->data, rate, rate, rate);
 	if (ret)
Signature · 1 line
2.17.1
author
#7 lore raw

PATCH 4/10 power: regulator: tps6236x: add support for tps6236x regulators

In reply to Keerthy

From: Tero Kristo <[email protected]>

TPS6236x is a family of step down DC-DC converters optimized for battery powered portable applications for a small solution size. Add a regulator driver for supporting these devices.

---
 drivers/power/regulator/Kconfig              |  10 ++
 drivers/power/regulator/Makefile             |   1 +
 drivers/power/regulator/tps62360_regulator.c | 123 +++++++++++++++++++
 3 files changed, 134 insertions(+)
 create mode 100644 drivers/power/regulator/tps62360_regulator.c
drivers/power/regulator/Kconfig +10 -0
index 9aa00fad42..56d68ee40e 100644
@@ -273,6 +273,16 @@ config DM_REGULATOR_TPS65910
 	regulator types of the TPS65910 (BUCK, BOOST and LDO). It implements
 	the get/set api for value and enable.
 
+config DM_REGULATOR_TPS62360
+	bool "Enable driver for TPS6236x Power Regulator"
+	depends on DM_REGULATOR
+	help
+	The TPS6236X DC/DC step down converter provides a single output
+	power line peaking at 3A current. This driver supports all four
+	variants of the chip (TPS62360, TPS62361, TPS62362, TPS62363). It
+	implements the get/set api for value only, as the power line is
+	always on.
+
 config DM_REGULATOR_STPMIC1
 	bool "Enable driver for STPMIC1 regulators"
 	depends on DM_REGULATOR && PMIC_STPMIC1
drivers/power/regulator/Makefile +1 -0
index 6a3d4bbee4..9198841b4f 100644
@@ -26,4 +26,5 @@ obj-$(CONFIG_$(SPL_)DM_REGULATOR_LP873X) += lp873x_regulator.o
 obj-$(CONFIG_$(SPL_)DM_REGULATOR_LP87565) += lp87565_regulator.o
 obj-$(CONFIG_$(SPL_)DM_REGULATOR_STM32_VREFBUF) += stm32-vrefbuf.o
 obj-$(CONFIG_DM_REGULATOR_TPS65910) += tps65910_regulator.o
+obj-$(CONFIG_DM_REGULATOR_TPS62360) += tps62360_regulator.o
 obj-$(CONFIG_$(SPL_)DM_REGULATOR_STPMIC1) += stpmic1.o
drivers/power/regulator/tps62360_regulator.c new file +123 -0

123 lines not on this page · raw message

Signature · 1 line
2.17.1
author
#8 lore raw

PATCH 5/10 arm: dts: k3-am65: Add VTM node

In reply to Keerthy

From: Tero Kristo <[email protected]>

Add VTM node for voltage and thermal management. For u-boot, this is needed for supporting AVS class 0, as the efuse values for the OPPs are stored under the VTM.

---
 arch/arm/dts/k3-am65-wakeup.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)
arch/arm/dts/k3-am65-wakeup.dtsi +7 -0
index 2676d6035b..5d050c6fd8 100644
@@ -62,4 +62,11 @@
 		clocks = <&k3_clks 115 1>;
 		power-domains = <&k3_pds 115 TI_SCI_PD_EXCLUSIVE>;
 	};
+
+	wkup_vtm0: wkup_vtm at 42050000 {
+		compatible = "ti,am654-vtm", "ti,am654-avs";
+		reg = <0x42050000 0x25c>;
+		power-domains = <&k3_pds 80>;
+		#thermal-sensor-cells = <1>;
+	};
 };
Signature · 1 line
2.17.1
author
#9 lore raw

PATCH 6/10 arm: dts: k3-am654-r5-base-board: enable wkup_i2c0 driver for spl

In reply to Keerthy

From: Tero Kristo <[email protected]>

Enable wkup_i2c0 as this is needed for voltage control.

---
 arch/arm/dts/k3-am654-r5-base-board.dts | 1 +
 1 file changed, 1 insertion(+)
arch/arm/dts/k3-am654-r5-base-board.dts +1 -0
index e31ed4fe64..a2c6c5a49d 100644
@@ -211,4 +211,5 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&wkup_i2c0_pins_default>;
 	clock-frequency = <400000>;
+	u-boot,dm-spl;
 };
Signature · 1 line
2.17.1
author
#10 lore raw

PATCH 7/10 arm: dts: k3-am654-r5-base-board: add supply rail for MPU

In reply to Keerthy

From: Tero Kristo <[email protected]>

MPU voltage on AM65x-evm is controlled via the TPS62363 chip attached to i2c0 bus. Add device node for this so that it can be controlled via a regulator driver.

---
 arch/arm/dts/k3-am654-r5-base-board.dts | 13 +++++++++++++
 1 file changed, 13 insertions(+)
arch/arm/dts/k3-am654-r5-base-board.dts +13 -0
index a2c6c5a49d..d6bd5def59 100644
@@ -212,4 +212,17 @@
 	pinctrl-0 = <&wkup_i2c0_pins_default>;
 	clock-frequency = <400000>;
 	u-boot,dm-spl;
+
+	vdd_mpu: tps62363 at 60 {
+		compatible = "ti,tps62363";
+		reg = <0x60>;
+		regulator-name = "VDD_MPU";
+		regulator-min-microvolt = <500000>;
+		regulator-max-microvolt = <1770000>;
+		regulator-always-on;
+		regulator-boot-on;
+		ti,vsel0-state-high;
+		ti,vsel1-state-high;
+		u-boot,dm-spl;
+	};
 };
Signature · 1 line
2.17.1
author
#11 lore raw

PATCH 8/10 arm: dts: k3-am654-r5-base-board: enable wkup_vtm0 node and link in supplies

In reply to Keerthy

From: Tero Kristo <[email protected]>

Link the vdd-supplies for the voltage domains under the VTM node. Also, enable the node under SPL. This will enable the AVS class 0 support on am65x-evm board.

---
 arch/arm/dts/k3-am654-r5-base-board.dts | 6 ++++++
 1 file changed, 6 insertions(+)
arch/arm/dts/k3-am654-r5-base-board.dts +6 -0
index d6bd5def59..0d924d0aae 100644
@@ -131,6 +131,12 @@
 	power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
 };
 
+&wkup_vtm0 {
+	vdd-supply-3 = <&vdd_mpu>;
+	vdd-supply-4 = <&vdd_mpu>;
+	u-boot,dm-spl;
+};
+
 &wkup_pmx0 {
 	u-boot,dm-spl;
 	wkup_uart0_pins_default: wkup_uart0_pins_default {
Signature · 1 line
2.17.1
author
#12 lore raw

PATCH 9/10 configs: am65x_evm_r5_defconfig: Enable TPS62363 regulator support

In reply to Keerthy

From: Tero Kristo <[email protected]>

TPS62363 is used to control the MPU_VDD voltage, so enable the driver for this.

---
 configs/am65x_evm_r5_defconfig | 1 +
 1 file changed, 1 insertion(+)
configs/am65x_evm_r5_defconfig +1 -0
index d0619e9b7a..a721b24ba4 100644
@@ -84,6 +84,7 @@ CONFIG_DM_REGULATOR=y
 CONFIG_SPL_DM_REGULATOR=y
 CONFIG_DM_REGULATOR_GPIO=y
 CONFIG_SPL_DM_REGULATOR_GPIO=y
+CONFIG_DM_REGULATOR_TPS62360=y
 CONFIG_RAM=y
 CONFIG_SPL_RAM=y
 CONFIG_K3_SYSTEM_CONTROLLER=y
Signature · 1 line
2.17.1
author
#13 lore raw

PATCH 10/10 configs: am65x_evm_r5_defconfig: Enable AVS class 0 support

In reply to Keerthy

From: Tero Kristo <[email protected]>

Enable AVS class 0 support for the R5 SPL bootloader.

---
 configs/am65x_evm_r5_defconfig | 1 +
 1 file changed, 1 insertion(+)
configs/am65x_evm_r5_defconfig +1 -0
index a721b24ba4..4f122808de 100644
@@ -99,3 +99,4 @@ CONFIG_TIMER=y
 CONFIG_SPL_TIMER=y
 CONFIG_OMAP_TIMER=y
 CONFIG_FS_FAT_MAX_CLUSTSIZE=16384
+CONFIG_K3_AVS0=y
Signature · 1 line
2.17.1