misc: Add AVS class 0 support for AM6
Subsystems (4)
v3 cover misc: Add AVS class 0 support for AM6
Adaptive Voltage Scaling is a technology used in TI SoCs to optimize the operating voltage based on characterization data written to efuse during production.
Add support for Adaptive Voltage scaling class 0 support for AM6 family of devices. Adaptive voltage scaling class 0 implies that optimized voltage values for a particular OPP of a particular voltage domain are read from Efuse and programmed on the pmic/regulator.
Tested on AM654-EVM for MPU @800 MHz.
Tested on J721e-evm for MPU.
The series is based on top of the branch:
https://github.com/lokeshvutla/u-boot/tree/devel/j721e-full-boot
Changes in v3:
* Extended the support for j721e-evm.
* Moved vtm node under r5-board dts.
Changes in v2:
* Avoided creation of new uclass. AVS driver is now under misc.
Keerthy (11):
clk: clk-ti-sci: Notify AVS driver upon setting clock rate
misc: k3_avs: Add j721e support
power: pmic: tps65941: Add support for tps65941 family of PMICs
power: regulator: tps65941: add regulator support
arm: mach-k3: am6_init: Initialize AVS class 0
arm: mach-k3: j721e_init: Initialize avs class 0
arm: dts: k3-am654-r5-base-board: Add VTM node
arm: dts: k3-j721e-r5-common-proc-board: Add VTM node
arm: dts: k3-j721e-r5-common: Add tps65941 node and dependent
wkup_i2c0 node
arm: dts: k3-j721e-r5-common-proc-board: Hook buck12_reg to vtm supply
configs: j721e_evm_r5_defconfig: Enable AVS Class 0 & dependent
configs
Tero Kristo (7):
misc: k3_avs: add driver for K3 Adaptive Voltage Scaling Class 0
power: regulator: tps6236x: add support for tps6236x regulators
arm: dts: k3-am654-r5-base-board: enable wkup_i2c0 driver for spl
arm: dts: k3-am654-r5-base-board: add supply rail for MPU
arm: dts: k3-am654-r5-base-board: enable wkup_vtm0 node and link in
supplies
configs: am65x_evm_r5_defconfig: Enable TPS62363 regulator support
configs: am65x_evm_r5_defconfig: Enable AVS class 0 support
arch/arm/dts/k3-am654-r5-base-board.dts | 27 ++ arch/arm/dts/k3-j721e-mcu-wakeup.dtsi | 11 + .../arm/dts/k3-j721e-r5-common-proc-board.dts | 44 ++ arch/arm/mach-k3/am6_init.c | 7 + arch/arm/mach-k3/j721e_init.c | 7 + configs/am65x_evm_r5_defconfig | 2 + configs/j721e_evm_r5_defconfig | 9 + drivers/clk/clk-ti-sci.c | 5 + drivers/misc/Kconfig | 9 + drivers/misc/Makefile | 1 + drivers/misc/k3_avs.c | 388 +++++++++++++++++ drivers/power/pmic/Kconfig | 7 + drivers/power/pmic/Makefile | 1 + drivers/power/pmic/tps65941.c | 83 ++++ drivers/power/regulator/Kconfig | 20 + drivers/power/regulator/Makefile | 2 + drivers/power/regulator/tps62360_regulator.c | 123 ++++++ drivers/power/regulator/tps65941_regulator.c | 407 ++++++++++++++++++ include/k3-avs.h | 30 ++ include/power/tps65941.h | 26 ++ 20 files changed, 1209 insertions(+) create mode 100644 drivers/misc/k3_avs.c create mode 100644 drivers/power/pmic/tps65941.c create mode 100644 drivers/power/regulator/tps62360_regulator.c create mode 100644 drivers/power/regulator/tps65941_regulator.c create mode 100644 include/k3-avs.h create mode 100644 include/power/tps65941.h
Signature · 1 line
2.17.1
PATCH v3 1/18 misc: k3_avs: add driver for K3 Adaptive Voltage Scaling Class 0
From: Tero Kristo <[email protected]>
Adaptive Voltage Scaling is a technology used in TI SoCs to optimize the operating voltage based on characterization data written to efuse during production. Add a driver to support this feature for K3 line of SoCs, initially for AM65x.
---
Changes in v3:
* No change
Changes in v2:
* Moved under drivers/misc.
drivers/misc/Kconfig | 9 ++ drivers/misc/Makefile | 1 + drivers/misc/k3_avs.c | 366 ++++++++++++++++++++++++++++++++++++++++++ include/k3-avs.h | 28 ++++ 4 files changed, 404 insertions(+) create mode 100644 drivers/misc/k3_avs.c create mode 100644 include/k3-avs.h
drivers/misc/Kconfig +9 -0
@@ -412,4 +412,13 @@ config IHS_FPGA by the devices. This driver supports both CON and CPU variants of the devices, depending on the device tree entry. +config K3_AVS0 + depends on ARCH_K3 && SPL_DM_REGULATOR + bool "AVS class 0 support for K3 devices" + help + K3 devices have the optimized voltage values for the main voltage + domains stored in efuse within the VTM IP. This driver reads the + optimized voltage from the efuse, so that it can be programmed + to the PMIC on board. + endmenu
drivers/misc/Makefile +1 -0
@@ -65,3 +65,4 @@ obj-$(CONFIG_TWL4030_LED) += twl4030_led.o obj-$(CONFIG_VEXPRESS_CONFIG) += vexpress_config.o obj-$(CONFIG_WINBOND_W83627) += winbond_w83627.o obj-$(CONFIG_JZ4780_EFUSE) += jz4780_efuse.o +obj-$(CONFIG_K3_AVS0) += k3_avs.o
drivers/misc/k3_avs.c new file +366 -0
366 lines not on this page · raw message
include/k3-avs.h new file +28 -0
@@ -0,0 +1,28 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Texas Instruments' K3 Adaptive Voltage Scaling driver +* +* Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/ +* Tero Kristo <[email protected]> +* +*/ + +#ifndef _K3_AVS0_ +#define _K3_AVS0_ + +#define AM6_VDD_WKUP 0 +#define AM6_VDD_MCU 1 +#define AM6_VDD_CORE 2 +#define AM6_VDD_MPU0 3 +#define AM6_VDD_MPU1 4 + +#define NUM_OPPS 4 + +#define AM6_OPP_NOM 1 +#define AM6_OPP_OD 2 +#define AM6_OPP_TURBO 3 + +int k3_avs_set_opp (struct udevice *dev,int vdd_id,int opp_id); +int k3_avs_notify_freq (int dev_id,int clk_id,u32 freq); + +#endif
Signature · 1 line
2.17.1
PATCH v3 1/18 misc: k3_avs: add driver for K3 Adaptive Voltage Scaling Class 0
Quoted 9 lines · Keerthy
From: Tero Kristo <[email protected]>
Adaptive Voltage Scaling is a technology used in TI SoCs to optimize the operating voltage based on characterization data written to efuse during production. Add a driver to support this feature for K3 line of SoCs, initially for AM65x.
Signed-off-by Tero Kristo <[email protected]>Signed-off-by Keerthy <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191108/47239eab/attachment.sig>
PATCH v3 2/18 clk: clk-ti-sci: Notify AVS driver upon setting clock rate
In reply to KeerthyNotify AVS driver upon setting clock rate so that voltage is changed accordingly.
---
Changes in v3:
* No change
Changes in v2:
* No change
drivers/clk/clk-ti-sci.c | 5 +++++ 1 file changed, 5 insertions(+)
drivers/clk/clk-ti-sci.c +5 -0
@@ -13,6 +13,7 @@#include <errno.h> #include <clk-uclass.h> #include <linux/soc/ti/ti_sci_protocol.h> +#include <k3-avs.h> /** * struct ti_sci_clk_data - clock controller information structure
@@ -101,6 +102,10 @@ static ulong ti_sci_clk_set_rate(struct clk *clk, ulong rate)debug ("%s(clk=%p, rate=%lu)\n" , __func__, clk, rate); +#ifdef CONFIG_K3_AVS0 +k3_avs_notify_freq (clk->id, clk->data, rate); +#endif +/* Ask for exact frequency by using same value for min/target/max */ ret = cops->set_freq (sci, clk->id, clk->data, rate, rate, rate);if (ret)
Signature · 1 line
2.17.1
PATCH v3 2/18 clk: clk-ti-sci: Notify AVS driver upon setting clock rate
Quoted 4 lines · Keerthy
Notify AVS driver upon setting clock rate so that voltage is changed accordingly.
Signed-off-by Keerthy <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191108/eb7906b9/attachment.sig>
PATCH v3 3/18 power: regulator: tps6236x: add support for tps6236x regulators
In reply to KeerthyFrom: Tero Kristo <[email protected]>
TPS6236x is a family of step down DC-DC converters optimized for battery powered portable applications for a small solution size. Add a regulator driver for supporting these devices.
---
Changes in v3:
* No change
Changes in v2:
* No change
drivers/power/regulator/Kconfig | 10 ++ drivers/power/regulator/Makefile | 1 + drivers/power/regulator/tps62360_regulator.c | 123 +++++++++++++++++++ 3 files changed, 134 insertions(+) create mode 100644 drivers/power/regulator/tps62360_regulator.c
drivers/power/regulator/Kconfig +10 -0
@@ -273,6 +273,16 @@ config DM_REGULATOR_TPS65910 regulator types of the TPS65910 (BUCK, BOOST and LDO). It implements the get/set api for value and enable. +config DM_REGULATOR_TPS62360 + bool "Enable driver for TPS6236x Power Regulator" + depends on DM_REGULATOR + help + The TPS6236X DC/DC step down converter provides a single output + power line peaking at 3A current. This driver supports all four + variants of the chip (TPS62360, TPS62361, TPS62362, TPS62363). It + implements the get/set api for value only, as the power line is + always on. + config DM_REGULATOR_STPMIC1 bool "Enable driver for STPMIC1 regulators" depends on DM_REGULATOR && PMIC_STPMIC1
drivers/power/regulator/Makefile +1 -0
@@ -26,4 +26,5 @@ obj-$(CONFIG_$(SPL_)DM_REGULATOR_LP873X) += lp873x_regulator.o obj-$(CONFIG_$(SPL_)DM_REGULATOR_LP87565) += lp87565_regulator.o obj-$(CONFIG_$(SPL_)DM_REGULATOR_STM32_VREFBUF) += stm32-vrefbuf.o obj-$(CONFIG_DM_REGULATOR_TPS65910) += tps65910_regulator.o +obj-$(CONFIG_DM_REGULATOR_TPS62360) += tps62360_regulator.o obj-$(CONFIG_$(SPL_)DM_REGULATOR_STPMIC1) += stpmic1.o
drivers/power/regulator/tps62360_regulator.c new file +123 -0
123 lines not on this page · raw message
Signature · 1 line
2.17.1
PATCH v3 3/18 power: regulator: tps6236x: add support for tps6236x regulators
Quoted 8 lines · Keerthy
From: Tero Kristo <[email protected]>
TPS6236x is a family of step down DC-DC converters optimized for battery powered portable applications for a small solution size. Add a regulator driver for supporting these devices.
Signed-off-by Tero Kristo <[email protected]>Signed-off-by Keerthy <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191108/4bef4f6e/attachment.sig>
PATCH v3 4/18 misc: k3_avs: Add j721e support
In reply to Keerthyj721e SoCs have different OPP tables. Add support for the same.
Note: DM Still has lot of voltages TBD hence the correct values need to be programmed once they are published.
---
Changes in v3:
* No change
Changes in v2:
* No change
drivers/misc/k3_avs.c | 22 ++++++++++++++++++++++ include/k3-avs.h | 2 ++ 2 files changed, 24 insertions(+)
drivers/misc/k3_avs.c +22 -0
@@ -347,6 +347,27 @@ static struct vd_data am654_vd_data[] = { { .id = -1 }, }; +static struct vd_data j721e_vd_data[] = { + { + .id =J721E_VDD_MPU , + .opp =AM6_OPP_NOM , + .dev_id =202 ,/* J721E_DEV_A72SS0_CORE0 */ + .clk_id =2 ,/* ARM clock */ + .opps = { + [AM6_OPP_NOM ] = { + .volt =880000 ,/* TBD in DM */ + .freq =2000000000 , + }, + }, + }, + { .id =-1 }, +}; + +static struct vd_config j721e_vd_config = { + .efuse_xlate = am6_efuse_xlate, + .vds = j721e_vd_data, +}; +static struct vd_config am654_vd_config = { .efuse_xlate = am6_efuse_xlate, .vds = am654_vd_data,
@@ -354,6 +375,7 @@ static struct vd_config am654_vd_config = {static const struct udevice_id k3_avs_ids[] = { { .compatible ="ti,am654-avs" , .data = (ulong)&am654_vd_config }, + { .compatible ="ti,j721e-avs" , .data = (ulong)&j721e_vd_config }, {} };
include/k3-avs.h +2 -0
@@ -16,6 +16,8 @@#define AM6_VDD_MPU0 3#define AM6_VDD_MPU1 4 +#define J721E_VDD_MPU 2 +#define NUM_OPPS 4#define AM6_OPP_NOM 1
Signature · 1 line
2.17.1
PATCH v3 4/18 misc: k3_avs: Add j721e support
Quoted 6 lines · Keerthy
j721e SoCs have different OPP tables. Add support for the same.
Note: DM Still has lot of voltages TBD hence the correct values need to be programmed once they are published.
Signed-off-by Keerthy <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191108/a38698fa/attachment.sig>
PATCH v3 5/18 power: pmic: tps65941: Add support for tps65941 family of PMICs
In reply to KeerthyAdd support to bind the regulators/child nodes with the pmic.
---
Changes in v3:
* No change
Changes in v2:
* No change
drivers/power/pmic/Kconfig | 7 +++ drivers/power/pmic/Makefile | 1 + drivers/power/pmic/tps65941.c | 83 +++++++++++++++++++++++++++++++++++ include/power/tps65941.h | 26 +++++++++++ 4 files changed, 117 insertions(+) create mode 100644 drivers/power/pmic/tps65941.c create mode 100644 include/power/tps65941.h
drivers/power/pmic/Kconfig +7 -0
@@ -267,3 +267,10 @@ config SPL_PMIC_LP87565 help The LP87565 is a PMIC containing a bunch of SMPS. This driver binds the pmic children in SPL. + +config PMIC_TPS65941 + bool "Enable driver for Texas Instruments TPS65941 PMIC" + depends on DM_PMIC + help + The TPS65941 is a PMIC containing a bunch of SMPS & LDOs. + This driver binds the pmic children.
drivers/power/pmic/Makefile +1 -0
@@ -39,3 +39,4 @@ obj-$(CONFIG_POWER_TPS65218) += pmic_tps65218.o obj-$(CONFIG_POWER_TPS65910) += pmic_tps65910.o obj-$(CONFIG_POWER_HI6553) += pmic_hi6553.o obj-$(CONFIG_POWER_MC34VR500) += pmic_mc34vr500.o +obj-$(CONFIG_PMIC_TPS65941) += tps65941.o
drivers/power/pmic/tps65941.c new file +83 -0
83 lines not on this page · raw message
include/power/tps65941.h new file +26 -0
@@ -0,0 +1,26 @@ +#define TPS659411 0x0 +#define TPS659412 0x1 +#define TPS659413 0x2 +#define TPS659414 0x3 + +/* I2C device address for pmic tps65941 */ +#define TPS65941_I2C_ADDR (0x12 >> 1) +#define TPS65941_LDO_NUM 4 +#define TPS65941_BUCK_NUM 5 + +/* Drivers name */ +#define TPS65941_LDO_DRIVER "tps65941_ldo" +#define TPS65941_BUCK_DRIVER "tps65941_buck" + +#define TPS65941_BUCK_VOLT_MASK 0xFF +#define TPS65941_BUCK_VOLT_MAX_HEX 0xFF +#define TPS65941_BUCK_VOLT_MAX 3340000 +#define TPS65941_BUCK_MODE_MASK 0x1 + +#define TPS65941_LDO_VOLT_MASK 0x3E +#define TPS65941_LDO_VOLT_MAX_HEX 0x3A +#define TPS65941_LDO_VOLT_MIN_HEX 0x4 +#define TPS65941_LDO_VOLT_MAX 3300000 +#define TPS65941_LDO_MODE_MASK 0x1 +#define TPS65941_LDO_BYPASS_EN 0x80 +#define TP65941_BUCK_CONF_SLEW_MASK 0x7
Signature · 1 line
2.17.1
PATCH v3 5/18 power: pmic: tps65941: Add support for tps65941 family of PMICs
Quoted 3 lines · Keerthy
Add support to bind the regulators/child nodes with the pmic.
Signed-off-by Keerthy <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191108/c094023a/attachment.sig>
PATCH v3 6/18 power: regulator: tps65941: add regulator support
In reply to KeerthyThe driver provides regulator set/get voltage enable/disable functions for tps65941 family of PMICs.
---
Changes in v3:
* No change
Changes in v2:
* No change
drivers/power/regulator/Kconfig | 10 + drivers/power/regulator/Makefile | 1 + drivers/power/regulator/tps65941_regulator.c | 407 +++++++++++++++++++ 3 files changed, 418 insertions(+) create mode 100644 drivers/power/regulator/tps65941_regulator.c
drivers/power/regulator/Kconfig +10 -0
@@ -323,3 +323,13 @@ config SPL_DM_REGULATOR_LP873X This enables implementation of driver-model regulator uclass features for REGULATOR LP873X and the family of LP873X PMICs. The driver implements get/set api for: value and enable in SPL. + +config DM_REGULATOR_TPS65941 + bool "Enable driver for TPS65941 PMIC regulators" + depends on PMIC_TPS65941 + help + This enables implementation of driver-model regulator uclass + features for REGULATOR TPS65941 and the family of TPS65941 PMICs. + TPS65941 series of PMICs have 5 single phase BUCKs that can also + be configured in multi phase modes & 4 LDOs. The driver implements + get/set api for value and enable.
drivers/power/regulator/Makefile +1 -0
@@ -28,3 +28,4 @@ obj-$(CONFIG_$(SPL_)DM_REGULATOR_STM32_VREFBUF) += stm32-vrefbuf.o obj-$(CONFIG_DM_REGULATOR_TPS65910) += tps65910_regulator.o obj-$(CONFIG_DM_REGULATOR_TPS62360) += tps62360_regulator.o obj-$(CONFIG_$(SPL_)DM_REGULATOR_STPMIC1) += stpmic1.o +obj-$(CONFIG_DM_REGULATOR_TPS65941) += tps65941_regulator.o
drivers/power/regulator/tps65941_regulator.c new file +407 -0
407 lines not on this page · raw message
Signature · 1 line
2.17.1
PATCH v3 6/18 power: regulator: tps65941: add regulator support
Quoted 4 lines · Keerthy
The driver provides regulator set/get voltage enable/disable functions for tps65941 family of PMICs.
Signed-off-by Keerthy <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191108/80672766/attachment.sig>
PATCH v3 7/18 arm: mach-k3: am6_init: Initialize AVS class 0
In reply to KeerthyInitialize AVS class 0 so that mpu voltage rail is programmed to the AVS class 0 compensated value.
---
Changes in v3:
* No change
Changes in v2:
* uclass_get_device_by_driver used in place getting the first uclass Instance.
arch/arm/mach-k3/am6_init.c | 7 +++++++ 1 file changed, 7 insertions(+)
arch/arm/mach-k3/am6_init.c +7 -0
@@ -116,6 +116,13 @@ void board_init_f(ulong dummy)/* Perform EEPROM-based board detection */ do_board_detect (); +#if defined(CONFIG_CPU_V7R ) && defined(CONFIG_K3_AVS0 ) + ret =uclass_get_device_by_driver (UCLASS_MISC ,DM_GET_DRIVER (k3_avs), + &dev); +if (ret) +printf ("AVS init failed: %d\n" , ret); +#endif +#ifdef CONFIG_K3_AM654_DDRSS ret =uclass_get_device (UCLASS_RAM ,0 , &dev);if (ret)
Signature · 1 line
2.17.1
PATCH v3 7/18 arm: mach-k3: am6_init: Initialize AVS class 0
Quoted 4 lines · Keerthy
Initialize AVS class 0 so that mpu voltage rail is programmed to the AVS class 0 compensated value.
Signed-off-by Keerthy <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191108/ed8d5778/attachment.sig>
PATCH v3 8/18 arm: mach-k3: j721e_init: Initialize avs class 0
In reply to KeerthyInitialize avs class 0
---
Changes in v3:
* No change
Changes in v2:
* No change
arch/arm/mach-k3/j721e_init.c | 7 +++++++ 1 file changed, 7 insertions(+)
arch/arm/mach-k3/j721e_init.c +7 -0
@@ -118,6 +118,13 @@ void board_init_f(ulong dummy)preloader_console_init ();#endif +#if defined(CONFIG_CPU_V7R ) && defined(CONFIG_K3_AVS0 ) + ret =uclass_get_device_by_driver (UCLASS_MISC ,DM_GET_DRIVER (k3_avs), + &dev); +if (ret) +printf ("AVS init failed: %d\n" , ret); +#endif +#if defined(CONFIG_K3_J721E_DDRSS ) ret =uclass_get_device (UCLASS_RAM ,0 , &dev);if (ret)
Signature · 1 line
2.17.1
PATCH v3 8/18 arm: mach-k3: j721e_init: Initialize avs class 0
Quoted 3 lines · Keerthy
Initialize avs class 0
Signed-off-by Keerthy <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191108/f0ff9f1d/attachment.sig>
PATCH v3 9/18 arm: dts: k3-am654-r5-base-board: Add VTM node
In reply to KeerthyAdd VTM node for voltage and thermal management. For u-boot, this is needed for supporting AVS class 0, as the efuse values for the OPPs are stored under the VTM.
---
Changes in v3:
* Moved from generic wakeup.dtsi to r5 board file.
Changes in v2:
* No change
arch/arm/dts/k3-am654-r5-base-board.dts | 7 +++++++ 1 file changed, 7 insertions(+)
arch/arm/dts/k3-am654-r5-base-board.dts +7 -0
@@ -97,6 +97,13 @@ u-boot,dm-spl; }; + wkup_vtm0: wkup_vtm at 42050000 { + compatible = "ti,am654-vtm", "ti,am654-avs"; + reg = <0x42050000 0x25c>; + power-domains = <&k3_pds 80>; + #thermal-sensor-cells = <1>; + }; + clk_200mhz: dummy_clock { compatible = "fixed-clock"; #clock-cells = <0>;
Signature · 1 line
2.17.1
PATCH v3 9/18 arm: dts: k3-am654-r5-base-board: Add VTM node
Quoted 6 lines · Keerthy
Add VTM node for voltage and thermal management. For u-boot, this is needed for supporting AVS class 0, as the efuse values for the OPPs are stored under the VTM.
Signed-off-by Tero Kristo <[email protected]>Signed-off-by Keerthy <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191108/77564446/attachment.sig>
PATCH v3 10/18 arm: dts: k3-am654-r5-base-board: enable wkup_i2c0 driver for spl
In reply to KeerthyFrom: Tero Kristo <[email protected]>
Enable wkup_i2c0 as this is needed for voltage control.
---
Changes in v3:
* No change
Changes in v2:
* No change
arch/arm/dts/k3-am654-r5-base-board.dts | 1 + 1 file changed, 1 insertion(+)
arch/arm/dts/k3-am654-r5-base-board.dts +1 -0
@@ -218,4 +218,5 @@ pinctrl-names = "default"; pinctrl-0 = <&wkup_i2c0_pins_default>; clock-frequency = <400000>; + u-boot,dm-spl; };
Signature · 1 line
2.17.1
PATCH v3 10/18 arm: dts: k3-am654-r5-base-board: enable wkup_i2c0 driver for spl
Quoted 6 lines · Keerthy
From: Tero Kristo <[email protected]>
Enable
wkup_i2c0as this is needed for voltage control.Signed-off-by Tero Kristo <[email protected]>Signed-off-by Keerthy <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191108/71431b34/attachment.sig>
PATCH v3 11/18 arm: dts: k3-am654-r5-base-board: add supply rail for MPU
In reply to KeerthyFrom: Tero Kristo <[email protected]>
MPU voltage on AM65x-evm is controlled via the TPS62363 chip attached to i2c0 bus. Add device node for this so that it can be controlled via a regulator driver.
---
Changes in v3:
* No change
Changes in v2:
* No change
arch/arm/dts/k3-am654-r5-base-board.dts | 13 +++++++++++++ 1 file changed, 13 insertions(+)
arch/arm/dts/k3-am654-r5-base-board.dts +13 -0
@@ -219,4 +219,17 @@ pinctrl-0 = <&wkup_i2c0_pins_default>; clock-frequency = <400000>; u-boot,dm-spl; + + vdd_mpu: tps62363 at 60 { + compatible = "ti,tps62363"; + reg = <0x60>; + regulator-name = "VDD_MPU"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1770000>; + regulator-always-on; + regulator-boot-on; + ti,vsel0-state-high; + ti,vsel1-state-high; + u-boot,dm-spl; + }; };
Signature · 1 line
2.17.1
PATCH v3 11/18 arm: dts: k3-am654-r5-base-board: add supply rail for MPU
Quoted 8 lines · Keerthy
From: Tero Kristo <[email protected]>
MPU voltage on AM65x-evm is controlled via the TPS62363 chip attached to i2c0 bus. Add device node for this so that it can be controlled via a regulator driver.
Signed-off-by Tero Kristo <[email protected]>Signed-off-by Keerthy <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191108/26c6ff01/attachment.sig>
PATCH v3 12/18 arm: dts: k3-am654-r5-base-board: enable wkup_vtm0 node and link in supplies
In reply to KeerthyFrom: Tero Kristo <[email protected]>
Link the vdd-supplies for the voltage domains under the VTM node. Also, enable the node under SPL. This will enable the AVS class 0 support on am65x-evm board.
---
Changes in v3:
* No change
Changes in v2:
* No change
arch/arm/dts/k3-am654-r5-base-board.dts | 6 ++++++ 1 file changed, 6 insertions(+)
arch/arm/dts/k3-am654-r5-base-board.dts +6 -0
@@ -138,6 +138,12 @@ power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>; }; +&wkup_vtm0 { + vdd-supply-3 = <&vdd_mpu>; + vdd-supply-4 = <&vdd_mpu>; + u-boot,dm-spl; +}; + &wkup_pmx0 { u-boot,dm-spl; wkup_uart0_pins_default: wkup_uart0_pins_default {
Signature · 1 line
2.17.1
PATCH v3 12/18 arm: dts: k3-am654-r5-base-board: enable wkup_vtm0 node and link in supplies
Quoted 8 lines · Keerthy
From: Tero Kristo <[email protected]>
Link the vdd-supplies for the voltage domains under the VTM node. Also, enable the node under SPL. This will enable the AVS class 0 support on am65x-evm board.
Signed-off-by Tero Kristo <[email protected]>Signed-off-by Keerthy <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191108/e6e18bb0/attachment.sig>
PATCH v3 13/18 arm: dts: k3-j721e-r5-common-proc-board: Add VTM node
In reply to KeerthyAdd VTM node for voltage and thermal management. For u-boot, this is needed for supporting AVS class 0, as the efuse values for the OPPs are stored under the VTM.
---
Changes in v3:
* No change
Changes in v2:
* No change
arch/arm/dts/k3-j721e-r5-common-proc-board.dts | 7 +++++++ 1 file changed, 7 insertions(+)
arch/arm/dts/k3-j721e-r5-common-proc-board.dts +7 -0
@@ -59,6 +59,13 @@ mboxes= <&mcu_secproxy 4>, <&mcu_secproxy 5>; mbox-names = "tx", "rx"; }; + + wkup_vtm0: wkup_vtm at 42040000 { + compatible = "ti,am654-vtm", "ti,j721e-avs"; + reg = <0x0 0x42040000 0x0 0x330>; + power-domains = <&k3_pds 154 TI_SCI_PD_EXCLUSIVE>; + #thermal-sensor-cells = <1>; + }; }; &dmsc {
Signature · 1 line
2.17.1
PATCH v3 13/18 arm: dts: k3-j721e-r5-common-proc-board: Add VTM node
Quoted 5 lines · Keerthy
Add VTM node for voltage and thermal management. For u-boot, this is needed for supporting AVS class 0, as the efuse values for the OPPs are stored under the VTM.
Signed-off-by Keerthy <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191108/7eff801b/attachment.sig>
PATCH v3 14/18 arm: dts: k3-j721e-r5-common: Add tps65941 node and dependent wkup_i2c0 node
In reply to KeerthyAdd tps65941 node and dependent wkup_i2c0 node needed for AVS class 0 support
---
Changes in v3:
* No change
Changes in v2:
* No change
arch/arm/dts/k3-j721e-mcu-wakeup.dtsi | 11 +++++++ .../arm/dts/k3-j721e-r5-common-proc-board.dts | 32 +++++++++++++++++++ 2 files changed, 43 insertions(+)
arch/arm/dts/k3-j721e-mcu-wakeup.dtsi +11 -0
@@ -57,6 +57,17 @@ clock-names = "fclk"; }; + wkup_i2c0: i2c at 42120000 { + compatible = "ti,j721e-i2c", "ti,omap4-i2c"; + reg = <0x0 0x42120000 0x0 0x100>; + interrupts = <GIC_SPI 896 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clock-names = "fck"; + clocks = <&k3_clks 197 0>; + power-domains = <&k3_pds 197 TI_SCI_PD_EXCLUSIVE>; + }; + mcu_uart0: serial at 40a00000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x40a00000 0x00 0x100>;
arch/arm/dts/k3-j721e-r5-common-proc-board.dts +32 -0
@@ -93,6 +93,13 @@ J721E_WKUP_IOPAD(0xe0, PIN_OUTPUT, 0) /* (G29) WKUP_GPIO0_12.MCU_UART0_TXD */ >; }; + + wkup_i2c0_pins_default: wkup-i2c0-pins-default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */ + J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */ + >; + }; }; &main_pmx0 {
@@ -147,4 +154,29 @@ ti,driver-strength-ohm = <50>; }; +&wkup_i2c0 { + u-boot,dm-spl; + tps659413a: tps659413a at 48 { + reg = <0x48>; + compatible = "ti,tps659413"; + u-boot,dm-spl; + pinctrl-names = "default"; + pinctrl-0 = <&wkup_i2c0_pins_default>; + clock-frequency = <400000>; + + regulators: regulators { + u-boot,dm-spl; + buck12_reg: buck12 { + /*VDD_MPU*/ + regulator-name = "buck12"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + u-boot,dm-spl; + }; + }; + }; +}; + #include "k3-j721e-common-proc-board-u-boot.dtsi"
Signature · 1 line
2.17.1
PATCH v3 14/18 arm: dts: k3-j721e-r5-common: Add tps65941 node and dependent wkup_i2c0 node
Quoted 3 lines · Keerthy
Add tps65941 node and dependent
wkup_i2c0node needed for AVS class 0 supportSigned-off-by Keerthy <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191108/0c20cd30/attachment.sig>
PATCH v3 15/18 arm: dts: k3-j721e-r5-common-proc-board: Hook buck12_reg to vtm supply
In reply to KeerthyHook buck12_reg to vtm avs supply
---
Changes in v3:
* No change
Changes in v2:
* No change
arch/arm/dts/k3-j721e-r5-common-proc-board.dts | 5 +++++ 1 file changed, 5 insertions(+)
arch/arm/dts/k3-j721e-r5-common-proc-board.dts +5 -0
@@ -179,4 +179,9 @@ }; }; +&wkup_vtm0 { + vdd-supply-2 = <&buck12_reg>; + u-boot,dm-spl; +}; + #include "k3-j721e-common-proc-board-u-boot.dtsi"
Signature · 1 line
2.17.1
PATCH v3 15/18 arm: dts: k3-j721e-r5-common-proc-board: Hook buck12_reg to vtm supply
Quoted 3 lines · Keerthy
Hook
buck12_regto vtm avs supplySigned-off-by Keerthy <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191108/3607eec7/attachment.sig>
PATCH v3 16/18 configs: am65x_evm_r5_defconfig: Enable TPS62363 regulator support
In reply to KeerthyFrom: Tero Kristo <[email protected]>
TPS62363 is used to control the MPU_VDD voltage, so enable the driver for this.
---
Changes in v3:
* No change
Changes in v2:
* No change
configs/am65x_evm_r5_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/am65x_evm_r5_defconfig +1 -0
@@ -84,6 +84,7 @@ CONFIG_DM_REGULATOR=y CONFIG_SPL_DM_REGULATOR=y CONFIG_DM_REGULATOR_GPIO=y CONFIG_SPL_DM_REGULATOR_GPIO=y +CONFIG_DM_REGULATOR_TPS62360=y CONFIG_RAM=y CONFIG_SPL_RAM=y CONFIG_K3_SYSTEM_CONTROLLER=y
Signature · 1 line
2.17.1
PATCH v3 16/18 configs: am65x_evm_r5_defconfig: Enable TPS62363 regulator support
Quoted 7 lines · Keerthy
From: Tero Kristo <[email protected]>
TPS62363 is used to control the
MPU_VDDvoltage, so enable the driver for this.Signed-off-by Tero Kristo <[email protected]>Signed-off-by Keerthy <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191108/13b77792/attachment.sig>
PATCH v3 17/18 configs: am65x_evm_r5_defconfig: Enable AVS class 0 support
In reply to KeerthyFrom: Tero Kristo <[email protected]>
Enable AVS class 0 support for the R5 SPL bootloader.
---
Changes in v3:
* No change
Changes in v2:
* No change
configs/am65x_evm_r5_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/am65x_evm_r5_defconfig +1 -0
@@ -99,3 +99,4 @@ CONFIG_TIMER=y CONFIG_SPL_TIMER=y CONFIG_OMAP_TIMER=y CONFIG_FS_FAT_MAX_CLUSTSIZE=16384 +CONFIG_K3_AVS0=y
Signature · 1 line
2.17.1
PATCH v3 17/18 configs: am65x_evm_r5_defconfig: Enable AVS class 0 support
Quoted 6 lines · Keerthy
From: Tero Kristo <[email protected]>
Enable AVS class 0 support for the R5 SPL bootloader.
Signed-off-by Tero Kristo <[email protected]>Signed-off-by Keerthy <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191108/66d720d3/attachment.sig>
PATCH v3 18/18 configs: j721e_evm_r5_defconfig: Enable AVS Class 0 & dependent configs
In reply to KeerthyEnable AVS Class 0 & dependent config options.
---
Changes in v3:
* No change
Changes in v2:
* No change
configs/j721e_evm_r5_defconfig | 9 +++++++++ 1 file changed, 9 insertions(+)
configs/j721e_evm_r5_defconfig +9 -0
@@ -59,10 +59,14 @@ CONFIG_CLK_TI_SCI=y CONFIG_TI_SCI_PROTOCOL=y CONFIG_DM_GPIO=y CONFIG_DA8XX_GPIO=y +CONFIG_DM_I2C=y +CONFIG_I2C_SET_DEFAULT_BUS_NUM=y +CONFIG_SYS_I2C_OMAP24XX=y CONFIG_DM_MAILBOX=y CONFIG_K3_SEC_PROXY=y CONFIG_MISC=y CONFIG_FS_LOADER=y +CONFIG_K3_AVS0=y CONFIG_DM_MMC=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_AM654=y
@@ -76,6 +80,11 @@ CONFIG_SPL_PINCTRL=y CONFIG_PINCTRL_SINGLE=y CONFIG_POWER_DOMAIN=y CONFIG_TI_SCI_POWER_DOMAIN=y +CONFIG_DM_PMIC=y +CONFIG_PMIC_TPS65941=y +CONFIG_DM_REGULATOR=y +CONFIG_SPL_DM_REGULATOR=y +CONFIG_DM_REGULATOR_TPS65941=y CONFIG_K3_SYSTEM_CONTROLLER=y CONFIG_REMOTEPROC_TI_K3_ARM64=y CONFIG_DM_RESET=y
Signature · 1 line
2.17.1
PATCH v3 18/18 configs: j721e_evm_r5_defconfig: Enable AVS Class 0 & dependent configs
Quoted 3 lines · Keerthy
Enable AVS Class 0 & dependent config options.
Signed-off-by Keerthy <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191108/2896ad82/attachment.sig>
v3 cover misc: Add AVS class 0 support for AM6
In reply to KeerthyQuoted 4 lines · Keerthy
Adaptive Voltage Scaling is a technology used in TI SoCs to optimize the operating voltage based on characterization data written to efuse during production.
Quoted 8 lines
Add support for Adaptive Voltage scaling class 0 support for AM6 family of devices. Adaptive voltage scaling class 0 implies that optimized voltage values for a particular OPP of a particular voltage domain are read from Efuse and programmed on the pmic/regulator.
Tested on AM654-EVM for MPU @800 MHz.
Tested on J721e-evm for MPU.
For the entire series:
Thanks and regards,
Lokesh
Quoted 67 lines
The series is based on top of the branch:
https://github.com/lokeshvutla/u-boot/tree/devel/j721e-full-boot
Changes in v3:
* Extended the support for j721e-evm.
* Moved vtm node under r5-board dts.Changes in v2:
* Avoided creation of new uclass. AVS driver is now under misc.
Keerthy (11):
clk: clk-ti-sci: Notify AVS driver upon setting clock rate
misc:k3_avs: Add j721e support
power: pmic: tps65941: Add support for tps65941 family of PMICs
power: regulator: tps65941: add regulator support
arm: mach-k3:am6_init: Initialize AVS class 0
arm: mach-k3:j721e_init: Initialize avs class 0
arm: dts: k3-am654-r5-base-board: Add VTM node
arm: dts: k3-j721e-r5-common-proc-board: Add VTM node
arm: dts: k3-j721e-r5-common: Add tps65941 node and dependent
wkup_i2c0node
arm: dts: k3-j721e-r5-common-proc-board: Hookbuck12_regto vtm supply
configs:j721e_evm_r5_defconfig: Enable AVS Class 0 & dependent
configsTero Kristo (7):
misc:k3_avs: add driver for K3 Adaptive Voltage Scaling Class 0
power: regulator: tps6236x: add support for tps6236x regulators
arm: dts: k3-am654-r5-base-board: enablewkup_i2c0driver for spl
arm: dts: k3-am654-r5-base-board: add supply rail for MPU
arm: dts: k3-am654-r5-base-board: enablewkup_vtm0node and link in
supplies
configs:am65x_evm_r5_defconfig: Enable TPS62363 regulator support
configs:am65x_evm_r5_defconfig: Enable AVS class 0 supportarch/arm/dts/k3-am654-r5-base-board.dts | 27 ++ arch/arm/dts/k3-j721e-mcu-wakeup.dtsi | 11 + .../arm/dts/k3-j721e-r5-common-proc-board.dts | 44 ++ arch/arm/mach-k3/am6_init.c | 7 + arch/arm/mach-k3/j721e_init.c | 7 + configs/am65x_evm_r5_defconfig | 2 + configs/j721e_evm_r5_defconfig | 9 + drivers/clk/clk-ti-sci.c | 5 + drivers/misc/Kconfig | 9 + drivers/misc/Makefile | 1 + drivers/misc/k3_avs.c | 388 +++++++++++++++++ drivers/power/pmic/Kconfig | 7 + drivers/power/pmic/Makefile | 1 + drivers/power/pmic/tps65941.c | 83 ++++ drivers/power/regulator/Kconfig | 20 + drivers/power/regulator/Makefile | 2 + drivers/power/regulator/tps62360_regulator.c | 123 ++++++ drivers/power/regulator/tps65941_regulator.c | 407 ++++++++++++++++++ include/k3-avs.h | 30 ++ include/power/tps65941.h | 26 ++ 20 files changed, 1209 insertions(+) create mode 100644 drivers/misc/k3_avs.c create mode 100644 drivers/power/pmic/tps65941.c create mode 100644 drivers/power/regulator/tps62360_regulator.c create mode 100644 drivers/power/regulator/tps65941_regulator.c create mode 100644 include/k3-avs.h create mode 100644 include/power/tps65941.h
v3 cover misc: Add AVS class 0 support for AM6
Quoted 16 lines · Lokesh Vutla
Quoted 4 lines · Keerthy
Adaptive Voltage Scaling is a technology used in TI SoCs to optimize the operating voltage based on characterization data written to efuse during production.
Quoted 8 lines
Add support for Adaptive Voltage scaling class 0 support for AM6 family of devices. Adaptive voltage scaling class 0 implies that optimized voltage values for a particular OPP of a particular voltage domain are read from Efuse and programmed on the pmic/regulator.
Tested on AM654-EVM for MPU @800 MHz.
Tested on J721e-evm for MPU.
Quoted 6 lines
For the entire series:
Reviewed-by Lokesh Vutla <[email protected]>Thanks and regards,
Lokesh
Tom,
If no further comments can this series be pulled in?
- Keerthy
Quoted 68 lines
Quoted 68 lines
The series is based on top of the branch:
https://github.com/lokeshvutla/u-boot/tree/devel/j721e-full-boot
Changes in v3:
* Extended the support for j721e-evm.
* Moved vtm node under r5-board dts.Changes in v2:
* Avoided creation of new uclass. AVS driver is now under misc.
Keerthy (11):
clk: clk-ti-sci: Notify AVS driver upon setting clock rate
misc:k3_avs: Add j721e support
power: pmic: tps65941: Add support for tps65941 family of PMICs
power: regulator: tps65941: add regulator support
arm: mach-k3:am6_init: Initialize AVS class 0
arm: mach-k3:j721e_init: Initialize avs class 0
arm: dts: k3-am654-r5-base-board: Add VTM node
arm: dts: k3-j721e-r5-common-proc-board: Add VTM node
arm: dts: k3-j721e-r5-common: Add tps65941 node and dependent
wkup_i2c0node
arm: dts: k3-j721e-r5-common-proc-board: Hookbuck12_regto vtm supply
configs:j721e_evm_r5_defconfig: Enable AVS Class 0 & dependent
configsTero Kristo (7):
misc:k3_avs: add driver for K3 Adaptive Voltage Scaling Class 0
power: regulator: tps6236x: add support for tps6236x regulators
arm: dts: k3-am654-r5-base-board: enablewkup_i2c0driver for spl
arm: dts: k3-am654-r5-base-board: add supply rail for MPU
arm: dts: k3-am654-r5-base-board: enablewkup_vtm0node and link in
supplies
configs:am65x_evm_r5_defconfig: Enable TPS62363 regulator support
configs:am65x_evm_r5_defconfig: Enable AVS class 0 supportarch/arm/dts/k3-am654-r5-base-board.dts | 27 ++ arch/arm/dts/k3-j721e-mcu-wakeup.dtsi | 11 + .../arm/dts/k3-j721e-r5-common-proc-board.dts | 44 ++ arch/arm/mach-k3/am6_init.c | 7 + arch/arm/mach-k3/j721e_init.c | 7 + configs/am65x_evm_r5_defconfig | 2 + configs/j721e_evm_r5_defconfig | 9 + drivers/clk/clk-ti-sci.c | 5 + drivers/misc/Kconfig | 9 + drivers/misc/Makefile | 1 + drivers/misc/k3_avs.c | 388 +++++++++++++++++ drivers/power/pmic/Kconfig | 7 + drivers/power/pmic/Makefile | 1 + drivers/power/pmic/tps65941.c | 83 ++++ drivers/power/regulator/Kconfig | 20 + drivers/power/regulator/Makefile | 2 + drivers/power/regulator/tps62360_regulator.c | 123 ++++++ drivers/power/regulator/tps65941_regulator.c | 407 ++++++++++++++++++ include/k3-avs.h | 30 ++ include/power/tps65941.h | 26 ++ 20 files changed, 1209 insertions(+)create mode 100644
drivers/misc/k3_avs.c
create mode 100644drivers/power/pmic/tps65941.ccreate mode 100644drivers/power/regulator/tps62360_regulator.ccreate mode 100644drivers/power/regulator/tps65941_regulator.ccreate mode 100644include/k3-avs.h
create mode 100644include/power/tps65941.h