dt-bindings: vendor-prefixes: add Seeed Studio
PATCH v2 1/3 dt-bindings: vendor-prefixes: add Seeed Studio
Add the "seeed" vendor prefix for Seeed Technology Co., Ltd
Website: https://www.seeedstudio.com/
--- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/vendor-prefixes.yaml +2 -0
@@ -902,6 +902,8 @@ patternProperties: description: Schindler "^seagate,.*": description: Seagate Technology PLC + "^seeed,.*": + description: Seeed Technology Co., Ltd "^seirobotics,.*": description: Shenzhen SEI Robotics Co., Ltd "^semtech,.*":
Signature · 1 line
2.27.0
PATCH v2 2/3 dt-bindings: arm: stm32: document Odyssey compatible
Document device tree bindings of Seeed SoM and carrier board.
--- Documentation/devicetree/bindings/arm/stm32/stm32.yaml | 2 ++ 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/arm/stm32/stm32.yaml +2 -0
@@ -39,6 +39,8 @@ properties: - enum: - arrow,stm32mp157a-avenger96 # Avenger96 - lxa,stm32mp157c-mc1 + - seeed,stm32mp157c-odyssey + - seeed,stm32mp157c-odyssey-som - shiratech,stm32mp157a-iot-box # IoT Box - shiratech,stm32mp157a-stinger96 # Stinger96 - st,stm32mp157c-ed1
Signature · 1 line
2.27.0
PATCH v2 3/3 ARM: dts: stm32: add initial support for stm32mp157-odyssey board
In reply to Marcin SloniewskiAdd support for Seeed Studio's stm32mp157c odyssey board. Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM and carrier board with USB and ETH interfaces, SD card connector, wifi and BT chip AP6236.
In this patch only basic kernel boot is supported and interfacing SD card and on-board eMMC.
---
Changes in v2:
- add new odyssey dts to Makefile
arch/arm/boot/dts/Makefile | 3 +- .../arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 276 ++++++++++++++++++ arch/arm/boot/dts/stm32mp157c-odyssey.dts | 72 +++++ 3 files changed, 350 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey.dts
arch/arm/boot/dts/Makefile +2 -1
@@ -1047,7 +1047,8 @@ dtb-$(CONFIG_ARCH_STM32) += \ stm32mp157c-dk2.dtb \ stm32mp157c-ed1.dtb \ stm32mp157c-ev1.dtb \ - stm32mp157c-lxa-mc1.dtb + stm32mp157c-lxa-mc1.dtb \ + stm32mp157c-odyssey.dtb dtb-$(CONFIG_MACH_SUN4I) += \ sun4i-a10-a1000.dtb \ sun4i-a10-ba10-tvbox.dtb \
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +276 -0
276 lines not on this page · raw message
arch/arm/boot/dts/stm32mp157c-odyssey.dts new file +72 -0
72 lines not on this page · raw message
Signature · 1 line
2.27.0
Re: [PATCH v2 3/3] ARM: dts: stm32: add initial support for stm32mp157-odyssey board
Hello Marcin,
Quoted 52 lines · Marcin Sloniewski
Add support for Seeed Studio's stm32mp157c odyssey board. Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM and carrier board with USB and ETH interfaces, SD card connector, wifi and BT chip AP6236.
In this patch only basic kernel boot is supported and interfacing SD card and on-board eMMC.
Signed-off-by Marcin Sloniewski <[email protected]>---
Changes in v2:
- add new odyssey dts toMakefilearch/arm/boot/dts/Makefile | 3 +- .../arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 276 ++++++++++++++++++ arch/arm/boot/dts/stm32mp157c-odyssey.dts | 72 +++++ 3 files changed, 350 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey.dtsarch/arm/boot/dts/Makefile +2
-1@@ -1047,7 +1047,8 @@ dtb-$(CONFIG_ARCH_STM32) += \ stm32mp157c-dk2.dtb \ stm32mp157c-ed1.dtb \ stm32mp157c-ev1.dtb \ - stm32mp157c-lxa-mc1.dtb + stm32mp157c-lxa-mc1.dtb \ + stm32mp157c-odyssey.dtb dtb-$(CONFIG_MACH_SUN4I) += \ sun4i-a10-a1000.dtb \ sun4i-a10-ba10-tvbox.dtb \arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +11
-0@@ -0,0 +1,276 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (C) 2020 Marcin Sloniewski <[email protected]>. + */ + +/dts-v1/; + +#include "stm32mp157.dtsi" +#include "stm32mp15xc.dtsi" +#include "stm32mp15-pinctrl.dtsi" +#include "stm32mp15xxac-pinctrl.dtsi"
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi line 21
Quoted 10 lines
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +10
-0+#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/mfd/st,stpmic1.h> + +/ { + model = "Seeed Studio Odyssey-STM32MP157C SOM"; + compatible = "seeed,stm32mp157c-odyssey-som", "st,stm32mp157"; + + memory@c0000000 { + reg = <0xc0000000 0x20000000>; + };
device_type = "memory"; is mandatory here per spec. There is no longer a skeleton.dtsi that adds this for you.
Quoted 41 lines
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +41
-0+ + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + mcuram2: mcuram2@10000000 { + compatible = "shared-dma-pool"; + reg = <0x10000000 0x40000>; + no-map; + }; + + vdev0vring0: vdev0vring0@10040000 { + compatible = "shared-dma-pool"; + reg = <0x10040000 0x1000>; + no-map; + }; + + vdev0vring1: vdev0vring1@10041000 { + compatible = "shared-dma-pool"; + reg = <0x10041000 0x1000>; + no-map; + }; + + vdev0buffer: vdev0buffer@10042000 { + compatible = "shared-dma-pool"; + reg = <0x10042000 0x4000>; + no-map; + }; + + mcuram: mcuram@30000000 { + compatible = "shared-dma-pool"; + reg = <0x30000000 0x40000>; + no-map; + }; + + retram: retram@38000000 { + compatible = "shared-dma-pool"; + reg = <0x38000000 0x10000>; + no-map; + };
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi line 72
Quoted 10 lines
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +10
-0+ + gpu_reserved: gpu@d4000000 { + reg = <0xd4000000 0x4000000>; + no-map; + }; + }; + + led { + compatible = "gpio-leds"; + blue {
This is not aligned with the leds-gpio.yaml binding. You could change it to led-blue. Run dtbs_check to find maybe more such issues.
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi line 73
Quoted 1 line
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +1
-0+ label = "heartbeat";
Per binding this is deprecated. Function/color should be used instead.
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi line 76
Quoted 3 lines
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +3
-0+ gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off";
Does it make sense to have a trigger but still default-state = "off"?
Quoted 16 lines
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +16
-0+ }; + }; +}; + +&gpu { + contiguous-area = <&gpu_reserved>; + status = "okay"; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /* spare dmas for other usage */
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi line 102
Quoted 10 lines
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +10
-0+ /delete-property/dmas; + /delete-property/dma-names; + + pmic: stpmic@33 { + compatible = "st,stpmic1"; + reg = <0x33>; + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + status = "okay";
status = "okay" is implied already here.
Quoted 112 lines
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +112
-0+ + regulators { + compatible = "st,stpmic1-regulators"; + ldo1-supply = <&v3v3>; + ldo3-supply = <&vdd_ddr>; + ldo6-supply = <&v3v3>; + pwr_sw1-supply = <&bst_out>; + pwr_sw2-supply = <&bst_out>; + + vddcore: buck1 { + regulator-name = "vddcore"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd_ddr: buck2 { + regulator-name = "vdd_ddr"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd: buck3 { + regulator-name = "vdd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + st,mask-reset; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + v3v3: buck4 { + regulator-name = "v3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-over-current-protection; + regulator-initial-mode = <0>; + }; + + v1v8_audio: ldo1 { + regulator-name = "v1v8_audio"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + interrupts = <IT_CURLIM_LDO1 0>; + }; + + v3v3_hdmi: ldo2 { + regulator-name = "v3v3_hdmi"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + interrupts = <IT_CURLIM_LDO2 0>; + }; + + vtt_ddr: ldo3 { + regulator-name = "vtt_ddr"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <750000>; + regulator-always-on; + regulator-over-current-protection; + }; + + vdd_usb: ldo4 { + regulator-name = "vdd_usb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + interrupts = <IT_CURLIM_LDO4 0>; + }; + + vdda: ldo5 { + regulator-name = "vdda"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + interrupts = <IT_CURLIM_LDO5 0>; + regulator-boot-on; + }; + + v1v2_hdmi: ldo6 { + regulator-name = "v1v2_hdmi"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + interrupts = <IT_CURLIM_LDO6 0>; + }; + + vref_ddr: vref_ddr { + regulator-name = "vref_ddr"; + regulator-always-on; + regulator-over-current-protection; + }; + + bst_out: boost { + regulator-name = "bst_out"; + interrupts = <IT_OCP_BOOST 0>; + }; + + vbus_otg: pwr_sw1 { + regulator-name = "vbus_otg"; + interrupts = <IT_OCP_OTG 0>; + }; + + vbus_sw: pwr_sw2 { + regulator-name = "vbus_sw"; + interrupts = <IT_OCP_SWOUT 0>;
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi line 224
Quoted 10 lines
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +10
-0+ regulator-active-discharge; + }; + }; + + onkey { + compatible = "st,stpmic1-onkey"; + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>; + interrupt-names = "onkey-falling", "onkey-rising"; + power-off-time-sec = <10>; + status = "okay";
Likewise, status = "okay" is implied already here.
Quoted 6 lines
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +6
-0+ }; + + watchdog { + compatible = "st,stpmic1-wdt"; + status = "disabled"; + };
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi line 240
Quoted 10 lines
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +10
-0+ }; +}; + +&ipcc { + status = "okay"; +}; + +&iwdg2 { + timeout-sec = <32>; + status = "okay";
Without knowing anything about your hardware design, are you sure you don't want to use the PMIC's watchdog instead? Imagine scaling down your CPU voltage and then getting a watchdog reset. Your CPU might not appreciate coming out of reset with full frequency but not enough voltage. If you regular reset is via PMIC, your watchdog reset should go through the PMIC as well.
Quoted 44 lines
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +36
-0+}; + +&m4_rproc { + memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>, + <&vdev0vring1>, <&vdev0buffer>; + mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>; + mbox-names = "vq0", "vq1", "shutdown"; + interrupt-parent = <&exti>; + interrupts = <68 1>; + status = "okay"; +}; + +&rng1 { + status = "okay"; +}; + +&rtc { + status = "okay"; +}; + +&sdmmc2 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>; + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>; + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>; + non-removable; + no-sd; + no-sdio; + st,neg-edge; + bus-width = <4>; + vmmc-supply = <&v3v3>; + vqmmc-supply = <&v3v3>; + mmc-ddr-3_3v; + status = "okay"; +}; +arch/arm/boot/dts/stm32mp157c-odyssey.dts new file +2
-0@@ -0,0 +1,72 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/*
arch/arm/boot/dts/stm32mp157c-odyssey.dts line 12
Quoted 10 lines
arch/arm/boot/dts/stm32mp157c-odyssey.dts new file +10
-0+ * Copyright (C) 2020 Marcin Sloniewski <[email protected]>. + */ + +/dts-v1/; + +#include "stm32mp157c-odyssey-som.dtsi" + +/ { + model = "Seeed Studio Odyssey-STM32MP157C Board"; + compatible = "seeed,stm32mp157c-odyssey", "st,stm32mp157";
A compatible for the SoM here could be useful as well, e.g. if bootloader needs to apply some fixups specific to the SoM.
Quoted 15 lines
arch/arm/boot/dts/stm32mp157c-odyssey.dts new file +15
-0+ + aliases { + ethernet0 = ðernet0; + serial0 = &uart4; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +ðernet0 { + status = "okay"; + pinctrl-0 = <ðernet0_rgmii_pins_a>; + pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>;
arch/arm/boot/dts/stm32mp157c-odyssey.dts line 37
Quoted 10 lines
arch/arm/boot/dts/stm32mp157c-odyssey.dts new file +10
-0+ pinctrl-names = "default", "sleep"; + phy-mode = "rgmii-id"; + max-speed = <1000>; + phy-handle = <&phy0>; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + phy0: ethernet-phy@0 {
Nitpick: I like it when there is a comment about the PHY in use.
arch/arm/boot/dts/stm32mp157c-odyssey.dts line 38
Quoted 1 line
arch/arm/boot/dts/stm32mp157c-odyssey.dts new file +1
-0+ reg = <0>;
Address 0 is the SMI broadcast address. Sure your PHY isn't strapped for another, non-broadcast, address?
Quoted 25 lines
arch/arm/boot/dts/stm32mp157c-odyssey.dts new file +24
-0+ }; + }; +}; + +&i2c1 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c1_pins_a>; + pinctrl-1 = <&i2c1_pins_sleep_a>; + i2c-scl-rising-time-ns = <100>; + i2c-scl-falling-time-ns = <7>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; +}; + +&sdmmc1 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc1_b4_pins_a>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; + cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + disable-wp; + st,neg-edge; + bus-width = <4>;
arch/arm/boot/dts/stm32mp157c-odyssey.dts line 72
Quoted 10 lines
arch/arm/boot/dts/stm32mp157c-odyssey.dts new file +10
-0+ vmmc-supply = <&v3v3>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&uart4_pins_a>; + status = "okay"; +}; +
Cheers,
Ahmad
Signature · 4 lines
Pengutronix e.K. | | Steuerwalder Str. 21 | http://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Re: [PATCH v2 3/3] ARM: dts: stm32: add initial support for stm32mp157-odyssey board
In reply to Marcin SloniewskiHi Marcin
Quoted 11 lines · Marcin Sloniewski
Add support for Seeed Studio's stm32mp157c odyssey board. Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM and carrier board with USB and ETH interfaces, SD card connector, wifi and BT chip AP6236.
In this patch only basic kernel boot is supported and interfacing SD card and on-board eMMC.
Signed-off-by Marcin Sloniewski <[email protected]>---
Build is failed on top if stm32-next due to ethernet / i2c1 pinctrl sleep nodes.
Can you fix please?
Quoted 385 lines
Changes in v2:
- add new odyssey dts toMakefilearch/arm/boot/dts/Makefile | 3 +- .../arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 276 ++++++++++++++++++ arch/arm/boot/dts/stm32mp157c-odyssey.dts | 72 +++++ 3 files changed, 350 insertions(+), 1 deletion(-)create mode 100644
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsicreate mode 100644arch/arm/boot/dts/stm32mp157c-odyssey.dtsarch/arm/boot/dts/Makefile +2
-1@@ -1047,7 +1047,8 @@ dtb-$(CONFIG_ARCH_STM32) += \ stm32mp157c-dk2.dtb \ stm32mp157c-ed1.dtb \ stm32mp157c-ev1.dtb \ - stm32mp157c-lxa-mc1.dtb + stm32mp157c-lxa-mc1.dtb \ + stm32mp157c-odyssey.dtb dtb-$(CONFIG_MACH_SUN4I) += \ sun4i-a10-a1000.dtb \ sun4i-a10-ba10-tvbox.dtb \arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +276
-0@@ -0,0 +1,276 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (C) 2020 Marcin Sloniewski <[email protected]>. + */ + +/dts-v1/; + +#include "stm32mp157.dtsi" +#include "stm32mp15xc.dtsi" +#include "stm32mp15-pinctrl.dtsi" +#include "stm32mp15xxac-pinctrl.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/mfd/st,stpmic1.h> + +/ { + model = "Seeed Studio Odyssey-STM32MP157C SOM"; + compatible = "seeed,stm32mp157c-odyssey-som", "st,stm32mp157"; + + memory@c0000000 { + reg = <0xc0000000 0x20000000>; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + mcuram2: mcuram2@10000000 { + compatible = "shared-dma-pool"; + reg = <0x10000000 0x40000>; + no-map; + }; + + vdev0vring0: vdev0vring0@10040000 { + compatible = "shared-dma-pool"; + reg = <0x10040000 0x1000>; + no-map; + }; + + vdev0vring1: vdev0vring1@10041000 { + compatible = "shared-dma-pool"; + reg = <0x10041000 0x1000>; + no-map; + }; + + vdev0buffer: vdev0buffer@10042000 { + compatible = "shared-dma-pool"; + reg = <0x10042000 0x4000>; + no-map; + }; + + mcuram: mcuram@30000000 { + compatible = "shared-dma-pool"; + reg = <0x30000000 0x40000>; + no-map; + }; + + retram: retram@38000000 { + compatible = "shared-dma-pool"; + reg = <0x38000000 0x10000>; + no-map; + }; + + gpu_reserved: gpu@d4000000 { + reg = <0xd4000000 0x4000000>; + no-map; + }; + }; + + led { + compatible = "gpio-leds"; + blue { + label = "heartbeat"; + gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + }; +}; + +&gpu { + contiguous-area = <&gpu_reserved>; + status = "okay"; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /* spare dmas for other usage */ + /delete-property/dmas; + /delete-property/dma-names; + + pmic: stpmic@33 { + compatible = "st,stpmic1"; + reg = <0x33>; + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + status = "okay"; + + regulators { + compatible = "st,stpmic1-regulators"; + ldo1-supply = <&v3v3>; + ldo3-supply = <&vdd_ddr>; + ldo6-supply = <&v3v3>; + pwr_sw1-supply = <&bst_out>; + pwr_sw2-supply = <&bst_out>; + + vddcore: buck1 { + regulator-name = "vddcore"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd_ddr: buck2 { + regulator-name = "vdd_ddr"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd: buck3 { + regulator-name = "vdd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + st,mask-reset; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + v3v3: buck4 { + regulator-name = "v3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-over-current-protection; + regulator-initial-mode = <0>; + }; + + v1v8_audio: ldo1 { + regulator-name = "v1v8_audio"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + interrupts = <IT_CURLIM_LDO1 0>; + }; + + v3v3_hdmi: ldo2 { + regulator-name = "v3v3_hdmi"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + interrupts = <IT_CURLIM_LDO2 0>; + }; + + vtt_ddr: ldo3 { + regulator-name = "vtt_ddr"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <750000>; + regulator-always-on; + regulator-over-current-protection; + }; + + vdd_usb: ldo4 { + regulator-name = "vdd_usb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + interrupts = <IT_CURLIM_LDO4 0>; + }; + + vdda: ldo5 { + regulator-name = "vdda"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + interrupts = <IT_CURLIM_LDO5 0>; + regulator-boot-on; + }; + + v1v2_hdmi: ldo6 { + regulator-name = "v1v2_hdmi"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + interrupts = <IT_CURLIM_LDO6 0>; + }; + + vref_ddr: vref_ddr { + regulator-name = "vref_ddr"; + regulator-always-on; + regulator-over-current-protection; + }; + + bst_out: boost { + regulator-name = "bst_out"; + interrupts = <IT_OCP_BOOST 0>; + }; + + vbus_otg: pwr_sw1 { + regulator-name = "vbus_otg"; + interrupts = <IT_OCP_OTG 0>; + }; + + vbus_sw: pwr_sw2 { + regulator-name = "vbus_sw"; + interrupts = <IT_OCP_SWOUT 0>; + regulator-active-discharge; + }; + }; + + onkey { + compatible = "st,stpmic1-onkey"; + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>; + interrupt-names = "onkey-falling", "onkey-rising"; + power-off-time-sec = <10>; + status = "okay"; + }; + + watchdog { + compatible = "st,stpmic1-wdt"; + status = "disabled"; + }; + }; +}; + +&ipcc { + status = "okay"; +}; + +&iwdg2 { + timeout-sec = <32>; + status = "okay"; +}; + +&m4_rproc { + memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>, + <&vdev0vring1>, <&vdev0buffer>; + mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>; + mbox-names = "vq0", "vq1", "shutdown"; + interrupt-parent = <&exti>; + interrupts = <68 1>; + status = "okay"; +}; + +&rng1 { + status = "okay"; +}; + +&rtc { + status = "okay"; +}; + +&sdmmc2 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>; + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>; + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>; + non-removable; + no-sd; + no-sdio; + st,neg-edge; + bus-width = <4>; + vmmc-supply = <&v3v3>; + vqmmc-supply = <&v3v3>; + mmc-ddr-3_3v; + status = "okay"; +}; +arch/arm/boot/dts/stm32mp157c-odyssey.dts new file +72
-0@@ -0,0 +1,72 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (C) 2020 Marcin Sloniewski <[email protected]>. + */ + +/dts-v1/; + +#include "stm32mp157c-odyssey-som.dtsi" + +/ { + model = "Seeed Studio Odyssey-STM32MP157C Board"; + compatible = "seeed,stm32mp157c-odyssey", "st,stm32mp157"; + + aliases { + ethernet0 = ðernet0; + serial0 = &uart4; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +ðernet0 { + status = "okay"; + pinctrl-0 = <ðernet0_rgmii_pins_a>; + pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>; + pinctrl-names = "default", "sleep"; + phy-mode = "rgmii-id"; + max-speed = <1000>; + phy-handle = <&phy0>; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + phy0: ethernet-phy@0 { + reg = <0>; + }; + }; +}; + +&i2c1 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c1_pins_a>; + pinctrl-1 = <&i2c1_pins_sleep_a>; + i2c-scl-rising-time-ns = <100>; + i2c-scl-falling-time-ns = <7>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; +}; + +&sdmmc1 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc1_b4_pins_a>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; + cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + disable-wp; + st,neg-edge; + bus-width = <4>; + vmmc-supply = <&v3v3>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&uart4_pins_a>; + status = "okay"; +}; +
Rob Herring
maintainerQuoted 9 lines · Marcin Sloniewski
Add the "seeed" vendor prefix for Seeed Technology Co., Ltd
Website: https://www.seeedstudio.com/Signed-off-by Marcin Sloniewski <[email protected]>Acked-by Rob Herring <[email protected]>--- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+)
Please add Acked-by/Reviewed-by tags when posting new versions. However, there's no need to repost patches *only* to add the tags. The upstream maintainer will do that for acks received on the version they apply.
If a tag was not added on purpose, please state why and what changed.