Skip to contentSkip to conversation

dt-bindings: vendor-prefixes: add Seeed Studio

PATCH In review Marcin Sloniewski 3 participants 5 messages Aug 9, 2020 – Aug 28, 2020

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v7 1/3 dt-bindings: vendor-prefixes: add Seeed Studio

Add the "seeed" vendor prefix for Seeed Technology Co., Ltd
Website: https://www.seeedstudio.com/

---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/vendor-prefixes.yaml +2 -0
index f3d847832fdc..cfde16a7084c 100644
@@ -910,6 +910,8 @@ patternProperties:
     description: Schindler
   "^seagate,.*":
     description: Seagate Technology PLC
+  "^seeed,.*":
+    description: Seeed Technology Co., Ltd
   "^seirobotics,.*":
     description: Shenzhen SEI Robotics Co., Ltd
   "^semtech,.*":
Signature · 1 line
2.27.0
#1 lore raw

PATCH v7 2/3 dt-bindings: arm: stm32: document Odyssey compatible

Document device tree bindings of Seeed SoM and carrier board.

---
 Documentation/devicetree/bindings/arm/stm32/stm32.yaml | 6 ++++++
 1 file changed, 6 insertions(+)
Documentation/devicetree/bindings/arm/stm32/stm32.yaml +6 -0
index 790e6dd48e34..3b318fe15194 100644
@@ -50,4 +50,10 @@ properties:
           - const: st,stm32mp157c-ev1
           - const: st,stm32mp157c-ed1
           - const: st,stm32mp157
+      - description: Odyssey STM32MP1 SoM based Boards
+        items:
+              - enum:
+                  - seeed,stm32mp157c-odyssey
+              - const: seeed,stm32mp157c-odyssey-som
+              - const: st,stm32mp157
 ...
Signature · 1 line
2.27.0
#2 lore raw

PATCH v7 3/3 ARM: dts: stm32: add initial support for stm32mp157-odyssey board

In reply to Marcin Sloniewski

Add support for Seeed Studio's stm32mp157c odyssey board. Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM and carrier board with USB and ETH interfaces, SD card connector, wifi and BT chip AP6236.

In this patch only basic kernel boot is supported and interfacing SD card and on-board eMMC.

---

Changes in v7:
- fix eth: added clock assignement for phy. It gets clock from PLL4_P which must be configured in u-boot/ATF as stmicroelectronics suggests.

Changes in v6:
- add reset pin for eth phy
- move pinctrl for sdmmc2 to stm32mp15-pinctrl.dtsi

Changes in v5:
- fix schema for board's dts

Changes in v4:
- add seeed,stm32mp157c-odyssey-som in compatible for carrier board
- fix sdmmc2 interface by changing one of the pins to use
- change eth phy address to 7

Changes in v3:
- fix compilation on tip of stm32-next
due to change in names for pinctrl
- fix deprecated binding for led node
- fix redundant "okay" statuses
- add phy part number for eth in comment

Changes in v2:
- add new odyssey dts to Makefile

 arch/arm/boot/dts/Makefile                    |   3 +-
 arch/arm/boot/dts/stm32mp15-pinctrl.dtsi      |  18 ++
 .../arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 276 ++++++++++++++++++
 arch/arm/boot/dts/stm32mp157c-odyssey.dts     |  80 +++++
 4 files changed, 376 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
 create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey.dts
arch/arm/boot/dts/Makefile +2 -1
index 4572db3fa5ae..f4a43a9420f1 100644
@@ -1056,7 +1056,8 @@ dtb-$(CONFIG_ARCH_STM32) += \
 	stm32mp157c-dk2.dtb \
 	stm32mp157c-ed1.dtb \
 	stm32mp157c-ev1.dtb \
-	stm32mp157c-lxa-mc1.dtb
+	stm32mp157c-lxa-mc1.dtb \
+	stm32mp157c-odyssey.dtb
 dtb-$(CONFIG_MACH_SUN4I) += \
 	sun4i-a10-a1000.dtb \
 	sun4i-a10-ba10-tvbox.dtb \
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi +18 -0
index b5a66429670c..a47eaecbde42 100644
@@ -1437,6 +1437,24 @@ pins {
 		};
 	};
 
+	sdmmc2_d47_pins_d: sdmmc2-d47-3 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('E', 5, AF9)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */
+		};
+	};
+
+	sdmmc2_d47_sleep_pins_d: sdmmc2-d47-sleep-3 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 9, ANALOG)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('E', 5, ANALOG)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('C', 7, ANALOG)>; /* SDMMC2_D7 */
+		};
+	};
+
 	sdmmc3_b4_pins_a: sdmmc3-b4-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('F', 0, AF9)>, /* SDMMC3_D0 */
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +276 -0

276 lines not on this page · raw message

arch/arm/boot/dts/stm32mp157c-odyssey.dts new file +80 -0

80 lines not on this page · raw message

Signature · 1 line
2.27.0
Reviewed-by on v7 3/3
#3 lore raw

Re: [PATCH v7 3/3] ARM: dts: stm32: add initial support for stm32mp157-odyssey board

Hello Marcin,

Quoted 9 lines · Marcin Sloniewski

Add support for Seeed Studio's stm32mp157c odyssey board. Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM and carrier board with USB and ETH interfaces, SD card connector, wifi and BT chip AP6236.

In this patch only basic kernel boot is supported and interfacing SD card and on-board eMMC.

arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi line 255

Quoted 6 lines

---

arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +4 -0
+
+&rng1 {
+	status = "okay";
+};

I think we should put this into the SoC dtsi instead.

Cheers
Ahmad

Signature · 4 lines
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
#4 lore raw

Re: [PATCH v7 3/3] ARM: dts: stm32: add initial support for stm32mp157-odyssey board

In reply to Marcin Sloniewski

Hi Marcin,

Quoted 10 lines · Marcin Sloniewski

Add support for Seeed Studio's stm32mp157c odyssey board. Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM and carrier board with USB and ETH interfaces, SD card connector, wifi and BT chip AP6236.

In this patch only basic kernel boot is supported and interfacing SD card and on-board eMMC.

---

Series applied on stm32-next.

Regards
Alex