dt-bindings: vendor-prefixes: add Seeed Studio
PATCH v5 1/3 dt-bindings: vendor-prefixes: add Seeed Studio
Add the "seeed" vendor prefix for Seeed Technology Co., Ltd
Website: https://www.seeedstudio.com/
--- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/vendor-prefixes.yaml +2 -0
@@ -902,6 +902,8 @@ patternProperties: description: Schindler "^seagate,.*": description: Seagate Technology PLC + "^seeed,.*": + description: Seeed Technology Co., Ltd "^seirobotics,.*": description: Shenzhen SEI Robotics Co., Ltd "^semtech,.*":
Signature · 1 line
2.27.0
PATCH v5 2/3 dt-bindings: arm: stm32: document Odyssey compatible
Document device tree bindings of Seeed SoM and carrier board.
--- Documentation/devicetree/bindings/arm/stm32/stm32.yaml | 6 ++++++ 1 file changed, 6 insertions(+)
Documentation/devicetree/bindings/arm/stm32/stm32.yaml +6 -0
@@ -50,4 +50,10 @@ properties: - const: st,stm32mp157c-ev1 - const: st,stm32mp157c-ed1 - const: st,stm32mp157 + - description: Odyssey STM32MP1 SoM based Boards + items: + - enum: + - seeed,stm32mp157c-odyssey + - const: seeed,stm32mp157c-odyssey-som + - const: st,stm32mp157 ...
Signature · 1 line
2.27.0
Re: [PATCH v5 2/3] dt-bindings: arm: stm32: document Odyssey compatible
Quoted 7 lines · Marcin Sloniewski
Document device tree bindings of Seeed SoM and carrier board.
Signed-off-by Marcin Sloniewski <[email protected]>--- Documentation/devicetree/bindings/arm/stm32/stm32.yaml | 6 ++++++ 1 file changed, 6 insertions(+)
PATCH v5 3/3 ARM: dts: stm32: add initial support for stm32mp157-odyssey board
In reply to Marcin SloniewskiAdd support for Seeed Studio's stm32mp157c odyssey board. Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM and carrier board with USB and ETH interfaces, SD card connector, wifi and BT chip AP6236.
In this patch only basic kernel boot is supported and interfacing SD card and on-board eMMC.
---
Changes in v5:
- fix schema for board's dts
Changes in v4:
- add seeed,stm32mp157c-odyssey-som in compatible for carrier board
- fix sdmmc2 interface by changing one of the pins to use
- change eth phy address to 7
Changes in v3:
- fix compilation on tip of stm32-next
due to change in names for pinctrl
- fix deprecated binding for led node
- fix redundant "okay" statuses
- add phy part number for eth in comment
Changes in v2:
- add new odyssey dts to Makefile
arch/arm/boot/dts/Makefile | 3 +- .../arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 294 ++++++++++++++++++ arch/arm/boot/dts/stm32mp157c-odyssey.dts | 73 +++++ 3 files changed, 369 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey.dts
arch/arm/boot/dts/Makefile +2 -1
@@ -1047,7 +1047,8 @@ dtb-$(CONFIG_ARCH_STM32) += \ stm32mp157c-dk2.dtb \ stm32mp157c-ed1.dtb \ stm32mp157c-ev1.dtb \ - stm32mp157c-lxa-mc1.dtb + stm32mp157c-lxa-mc1.dtb \ + stm32mp157c-odyssey.dtb dtb-$(CONFIG_MACH_SUN4I) += \ sun4i-a10-a1000.dtb \ sun4i-a10-ba10-tvbox.dtb \
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +294 -0
294 lines not on this page · raw message
arch/arm/boot/dts/stm32mp157c-odyssey.dts new file +73 -0
73 lines not on this page · raw message
Signature · 1 line
2.27.0
Re: [PATCH v5 3/3] ARM: dts: stm32: add initial support for stm32mp157-odyssey board
Hello Marcin,
Quoted 325 lines · Marcin Sloniewski
Add support for Seeed Studio's stm32mp157c odyssey board. Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM and carrier board with USB and ETH interfaces, SD card connector, wifi and BT chip AP6236.
In this patch only basic kernel boot is supported and interfacing SD card and on-board eMMC.
Signed-off-by Marcin Sloniewski <[email protected]>---
Changes in v5:
- fix schema for board's dtsChanges in v4:
- add seeed,stm32mp157c-odyssey-som in compatible for carrier board
- fix sdmmc2 interface by changing one of the pins to use
- change eth phy address to 7Changes in v3:
- fix compilation on tip of stm32-next
due to change in names for pinctrl
- fix deprecated binding for led node
- fix redundant "okay" statuses
- add phy part number for eth in commentChanges in v2:
- add new odyssey dts toMakefilearch/arm/boot/dts/Makefile | 3 +- .../arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 294 ++++++++++++++++++ arch/arm/boot/dts/stm32mp157c-odyssey.dts | 73 +++++ 3 files changed, 369 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey.dtsarch/arm/boot/dts/Makefile +2
-1@@ -1047,7 +1047,8 @@ dtb-$(CONFIG_ARCH_STM32) += \ stm32mp157c-dk2.dtb \ stm32mp157c-ed1.dtb \ stm32mp157c-ev1.dtb \ - stm32mp157c-lxa-mc1.dtb + stm32mp157c-lxa-mc1.dtb \ + stm32mp157c-odyssey.dtb dtb-$(CONFIG_MACH_SUN4I) += \ sun4i-a10-a1000.dtb \ sun4i-a10-ba10-tvbox.dtb \arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +267
-0@@ -0,0 +1,294 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (C) 2020 Marcin Sloniewski <[email protected]>. + */ + +/dts-v1/; + +#include "stm32mp157.dtsi" +#include "stm32mp15xc.dtsi" +#include "stm32mp15-pinctrl.dtsi" +#include "stm32mp15xxac-pinctrl.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/mfd/st,stpmic1.h> + +/ { + model = "Seeed Studio Odyssey-STM32MP157C SOM"; + compatible = "seeed,stm32mp157c-odyssey-som", "st,stm32mp157"; + + memory@c0000000 { + device_type = "memory"; + reg = <0xc0000000 0x20000000>; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + mcuram2: mcuram2@10000000 { + compatible = "shared-dma-pool"; + reg = <0x10000000 0x40000>; + no-map; + }; + + vdev0vring0: vdev0vring0@10040000 { + compatible = "shared-dma-pool"; + reg = <0x10040000 0x1000>; + no-map; + }; + + vdev0vring1: vdev0vring1@10041000 { + compatible = "shared-dma-pool"; + reg = <0x10041000 0x1000>; + no-map; + }; + + vdev0buffer: vdev0buffer@10042000 { + compatible = "shared-dma-pool"; + reg = <0x10042000 0x4000>; + no-map; + }; + + mcuram: mcuram@30000000 { + compatible = "shared-dma-pool"; + reg = <0x30000000 0x40000>; + no-map; + }; + + retram: retram@38000000 { + compatible = "shared-dma-pool"; + reg = <0x38000000 0x10000>; + no-map; + }; + + gpu_reserved: gpu@d4000000 { + reg = <0xd4000000 0x4000000>; + no-map; + }; + }; + + led { + compatible = "gpio-leds"; + led-blue { + color = <LED_COLOR_ID_BLUE>; + function = LED_FUNCTION_HEARTBEAT; + gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +&gpu { + contiguous-area = <&gpu_reserved>; + status = "okay"; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /* spare dmas for other usage */ + /delete-property/dmas; + /delete-property/dma-names; + + pmic: stpmic@33 { + compatible = "st,stpmic1"; + reg = <0x33>; + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + + regulators { + compatible = "st,stpmic1-regulators"; + ldo1-supply = <&v3v3>; + ldo3-supply = <&vdd_ddr>; + ldo6-supply = <&v3v3>; + pwr_sw1-supply = <&bst_out>; + pwr_sw2-supply = <&bst_out>; + + vddcore: buck1 { + regulator-name = "vddcore"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd_ddr: buck2 { + regulator-name = "vdd_ddr"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd: buck3 { + regulator-name = "vdd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + st,mask-reset; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + v3v3: buck4 { + regulator-name = "v3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-over-current-protection; + regulator-initial-mode = <0>; + }; + + v1v8_audio: ldo1 { + regulator-name = "v1v8_audio"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + interrupts = <IT_CURLIM_LDO1 0>; + }; + + v3v3_hdmi: ldo2 { + regulator-name = "v3v3_hdmi"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + interrupts = <IT_CURLIM_LDO2 0>; + }; + + vtt_ddr: ldo3 { + regulator-name = "vtt_ddr"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <750000>; + regulator-always-on; + regulator-over-current-protection; + }; + + vdd_usb: ldo4 { + regulator-name = "vdd_usb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + interrupts = <IT_CURLIM_LDO4 0>; + }; + + vdda: ldo5 { + regulator-name = "vdda"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + interrupts = <IT_CURLIM_LDO5 0>; + regulator-boot-on; + }; + + v1v2_hdmi: ldo6 { + regulator-name = "v1v2_hdmi"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + interrupts = <IT_CURLIM_LDO6 0>; + }; + + vref_ddr: vref_ddr { + regulator-name = "vref_ddr"; + regulator-always-on; + regulator-over-current-protection; + }; + + bst_out: boost { + regulator-name = "bst_out"; + interrupts = <IT_OCP_BOOST 0>; + }; + + vbus_otg: pwr_sw1 { + regulator-name = "vbus_otg"; + interrupts = <IT_OCP_OTG 0>; + }; + + vbus_sw: pwr_sw2 { + regulator-name = "vbus_sw"; + interrupts = <IT_OCP_SWOUT 0>; + regulator-active-discharge; + }; + }; + + onkey { + compatible = "st,stpmic1-onkey"; + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>; + interrupt-names = "onkey-falling", "onkey-rising"; + power-off-time-sec = <10>; + }; + + watchdog { + compatible = "st,stpmic1-wdt"; + status = "disabled"; + }; + }; +}; + +&ipcc { + status = "okay"; +}; + +&iwdg2 { + timeout-sec = <32>; + status = "okay"; +}; + +&m4_rproc { + memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>, + <&vdev0vring1>, <&vdev0buffer>; + mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>; + mbox-names = "vq0", "vq1", "shutdown"; + interrupt-parent = <&exti>; + interrupts = <68 1>; + status = "okay"; +}; + +&rng1 { + status = "okay"; +}; + +&rtc { + status = "okay"; +}; + +&sdmmc2_d47_pins_a { + pins { + pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */ + <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */ + <STM32_PINMUX('E', 5, AF9)>, /* SDMMC2_D6 */ + <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */ + };
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi line 277
Quoted 10 lines
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +10
-0+}; + +&sdmmc2_d47_sleep_pins_a { + pins { + pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */ + <STM32_PINMUX('A', 9, ANALOG)>, /* SDMMC2_D5 */ + <STM32_PINMUX('E', 5, ANALOG)>, /* SDMMC2_D6 */ + <STM32_PINMUX('C', 7, ANALOG)>; /* SDMMC2_D7 */ + }; +};
When I sent out the device trees for the lxa-mc1, Alex wanted all pinctrl nodes to be collected in stm32mp15-pinctrl.dtsi.
@Alex, should this be done here as well?
Quoted 52 lines
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +17
-0+ +&sdmmc2 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>; + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>; + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>; + non-removable; + no-sd; + no-sdio; + st,neg-edge; + bus-width = <8>; + vmmc-supply = <&v3v3>; + vqmmc-supply = <&v3v3>; + mmc-ddr-3_3v; + status = "okay"; +}; +arch/arm/boot/dts/stm32mp157c-odyssey.dts new file +29
-0@@ -0,0 +1,73 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (C) 2020 Marcin Sloniewski <[email protected]>. + */ + +/dts-v1/; + +#include "stm32mp157c-odyssey-som.dtsi" + +/ { + model = "Seeed Studio Odyssey-STM32MP157C Board"; + compatible = "seeed,stm32mp157c-odyssey", + "seeed,stm32mp157c-odyssey-som", "st,stm32mp157"; + + aliases { + ethernet0 = ðernet0; + serial0 = &uart4; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +ðernet0 { + status = "okay"; + pinctrl-0 = <ðernet0_rgmii_pins_a>; + pinctrl-1 = <ðernet0_rgmii_sleep_pins_a>; + pinctrl-names = "default", "sleep";
arch/arm/boot/dts/stm32mp157c-odyssey.dts line 39
Quoted 10 lines
arch/arm/boot/dts/stm32mp157c-odyssey.dts new file +10
-0+ phy-mode = "rgmii-id"; + max-speed = <1000>; + phy-handle = <&phy0>; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + phy0: ethernet-phy@7 { /* KSZ9031RN */ + reg = <7>;
reset-gpios is missing. I see that the vendor u-boot does it in board code, but you don't want Linux to depend on this.
Quoted 35 lines
arch/arm/boot/dts/stm32mp157c-odyssey.dts new file +34
-0+ }; + }; +}; + +&i2c1 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c1_pins_a>; + pinctrl-1 = <&i2c1_sleep_pins_a>; + i2c-scl-rising-time-ns = <100>; + i2c-scl-falling-time-ns = <7>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; +}; + +&sdmmc1 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc1_b4_pins_a>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; + cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + disable-wp; + st,neg-edge; + bus-width = <4>; + vmmc-supply = <&v3v3>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&uart4_pins_a>; + status = "okay"; +}; +
Signature · 4 lines
Pengutronix e.K. | | Steuerwalder Str. 21 | http://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Re: [PATCH v5 3/3] ARM: dts: stm32: add initial support for stm32mp157-odyssey board
...
Quoted 22 lines
Quoted 8 lines
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +8
-0+ +&sdmmc2_d47_pins_a { + pins { + pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */ + <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */ + <STM32_PINMUX('E', 5, AF9)>, /* SDMMC2_D6 */ + <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */ + };arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi line 277
Quoted 10 lines
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +10
-0+}; + +&sdmmc2_d47_sleep_pins_a { + pins { + pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */ + <STM32_PINMUX('A', 9, ANALOG)>, /* SDMMC2_D5 */ + <STM32_PINMUX('E', 5, ANALOG)>, /* SDMMC2_D6 */ + <STM32_PINMUX('C', 7, ANALOG)>; /* SDMMC2_D7 */ + }; +};When I sent out the device trees for the lxa-mc1, Alex wanted all pinctrl nodes to be collected in
stm32mp15-pinctrl.dtsi.
Quoted 1 line
@Alex, should this be done here as well?
Hi,
Sorry for the late answer. Yes it has to be defined in stm32mp15-pinctrl.dtsi. If at the end there are too much definitions for the same pins or group of pins, I'll find a smarter way for pin definition, but currently all pin definitions have to be done in stm32mp15-pinctrl.dtsi.
cheers
Alex
Quoted 94 lines
Quoted 53 lines
arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi new file +17
-0+ +&sdmmc2 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>; + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>; + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>; + non-removable; + no-sd; + no-sdio; + st,neg-edge; + bus-width = <8>; + vmmc-supply = <&v3v3>; + vqmmc-supply = <&v3v3>; + mmc-ddr-3_3v; + status = "okay"; +}; +arch/arm/boot/dts/stm32mp157c-odyssey.dts new file +29
-0@@ -0,0 +1,73 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (C) 2020 Marcin Sloniewski <[email protected]>. + */ + +/dts-v1/; + +#include "stm32mp157c-odyssey-som.dtsi" + +/ { + model = "Seeed Studio Odyssey-STM32MP157C Board"; + compatible = "seeed,stm32mp157c-odyssey", + "seeed,stm32mp157c-odyssey-som", "st,stm32mp157"; + + aliases { + ethernet0 = ðernet0; + serial0 = &uart4; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +ðernet0 { + status = "okay"; + pinctrl-0 = <ðernet0_rgmii_pins_a>; + pinctrl-1 = <ðernet0_rgmii_sleep_pins_a>; + pinctrl-names = "default", "sleep";arch/arm/boot/dts/stm32mp157c-odyssey.dts line 39
Quoted 10 lines
arch/arm/boot/dts/stm32mp157c-odyssey.dts new file +10
-0+ phy-mode = "rgmii-id"; + max-speed = <1000>; + phy-handle = <&phy0>; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + phy0: ethernet-phy@7 { /* KSZ9031RN */ + reg = <7>;reset-gpios is missing. I see that the vendor u-boot does it in board code, but you don't want Linux to depend on this.
Quoted 27 lines
arch/arm/boot/dts/stm32mp157c-odyssey.dts new file +27
-0+ }; + }; +}; + +&i2c1 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c1_pins_a>; + pinctrl-1 = <&i2c1_sleep_pins_a>; + i2c-scl-rising-time-ns = <100>; + i2c-scl-falling-time-ns = <7>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; +}; + +&sdmmc1 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc1_b4_pins_a>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; + cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + disable-wp; + st,neg-edge; + bus-width = <4>; + vmmc-supply = <&v3v3>; + status = "okay"; +};
Quoted 9 lines
arch/arm/boot/dts/stm32mp157c-odyssey.dts line 73
Quoted 8 lines
arch/arm/boot/dts/stm32mp157c-odyssey.dts new file +7
-0+ +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&uart4_pins_a>; + status = "okay"; +}; +
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel