Enable RPi header on j721e sk
Subsystems (3)
v4 cover Enable RPi header on j721e sk
The following series of patches enables RPi header on j721e sk. It is a 40 pin io expasion header which brings out i2c5, ehrpwm 2,3 and some pins of gpio 0,1
v4:
- Correct the node name in dt binding example
v3:
- Change node name from clock to clock-controller
- Add correct description for clock-controller node
v2:
- Add full path for clock property $ref
- Remove the discription for clock pattern property, since $ref is added
- Remove the label in the example
- Fix the indentation in the example
Rahul T R (1):
dt-bindings: mfd: ti,j721e-system-controller: Add clock property
Sinthu Raja (1):
arm64: dts: ti: k3-j721e-sk: Add pinmux for RPi Header
Vijay Pothukuchi (1):
arm64: dts: ti: k3-j721e-*: Add dts nodes for EHRPWMs
.../mfd/ti,j721e-system-controller.yaml | 12 +++ .../dts/ti/k3-j721e-common-proc-board.dts | 24 +++++ arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 62 ++++++++++- arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 101 +++++++++++++++++- 4 files changed, 193 insertions(+), 6 deletions(-)
Signature · 1 line
2.17.1
PATCH v4 1/3 dt-bindings: mfd: ti,j721e-system-controller: Add clock property
Add a pattern property for clock-controller, also update the example with a clock-controller node
--- .../bindings/mfd/ti,j721e-system-controller.yaml | 12 ++++++++++++ 1 file changed, 12 insertions(+)
Documentation/devicetree/bindings/mfd/ti,j721e-system-controller.yaml +12 -0
@@ -48,6 +48,12 @@ patternProperties: description: This is the SERDES lane control mux. + "^clock-controller@[0-9a-f]+$": + type: object + $ref: /schemas/clock/ti,am654-ehrpwm-tbclk.yaml# + description: + Clock provider for TI EHRPWM nodes. + required: - compatible - reg
@@ -79,5 +85,11 @@ examples: <0x40c0 0x3>, <0x40c4 0x3>, <0x40c8 0x3>, <0x40cc 0x3>; /* SERDES4 lane0/1/2/3 select */ }; + + clock-controller@4140 { + compatible = "ti,am654-ehrpwm-tbclk", "syscon"; + reg = <0x4140 0x18>; + #clock-cells = <1>; + }; }; ...
Signature · 1 line
2.17.1
Re: [PATCH v4 1/3] dt-bindings: mfd: ti,j721e-system-controller: Add clock property
Quoted 7 lines · Rahul T R
Add a pattern property for clock-controller, also update the example with a clock-controller node
Signed-off-by Rahul T R <[email protected]>--- .../bindings/mfd/ti,j721e-system-controller.yaml | 12 ++++++++++++ 1 file changed, 12 insertions(+)
Best regards,
Krzysztof
Lee Jones
AppliedRe: [PATCH v4 1/3] dt-bindings: mfd: ti,j721e-system-controller: Add clock property
In reply to Rahul T RQuoted 7 lines · Rahul T R
Add a pattern property for clock-controller, also update the example with a clock-controller node
Signed-off-by Rahul T R <[email protected]>--- .../bindings/mfd/ti,j721e-system-controller.yaml | 12 ++++++++++++ 1 file changed, 12 insertions(+)
Applied, thanks.
Signature · 4 lines
Lee Jones [李琼斯] Principal Technical Lead - Developer Services Linaro.org │ Open source software for Arm SoCs Follow Linaro: Facebook | Twitter | Blog
PATCH v4 2/3 arm64: dts: ti: k3-j721e-*: Add dts nodes for EHRPWMs
In reply to Rahul T RFrom: Vijay Pothukuchi <[email protected]>
Add dts nodes for 6 EHRPWM instances on SoC
--- .../dts/ti/k3-j721e-common-proc-board.dts | 24 +++++++ arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 62 ++++++++++++++++++- arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 24 +++++++ 3 files changed, 109 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts +24 -0
@@ -995,3 +995,27 @@ &main_mcan13 { status = "disabled"; }; + +&main_ehrpwm0 { + status = "disabled"; +}; + +&main_ehrpwm1 { + status = "disabled"; +}; + +&main_ehrpwm2 { + status = "disabled"; +}; + +&main_ehrpwm3 { + status = "disabled"; +}; + +&main_ehrpwm4 { + status = "disabled"; +}; + +&main_ehrpwm5 { + status = "disabled"; +};
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +61 -1
68 lines not on this page · raw message
arch/arm64/boot/dts/ti/k3-j721e-sk.dts +24 -0
@@ -1129,3 +1129,27 @@ memory-region = <&c71_0_dma_memory_region>, <&c71_0_memory_region>; }; + +&main_ehrpwm0 { + status = "disabled"; +}; + +&main_ehrpwm1 { + status = "disabled"; +}; + +&main_ehrpwm2 { + status = "disabled"; +}; + +&main_ehrpwm3 { + status = "disabled"; +}; + +&main_ehrpwm4 { + status = "disabled"; +}; + +&main_ehrpwm5 { + status = "disabled"; +};
Signature · 1 line
2.17.1
Nishanth Menon
maintainerRe: [PATCH v4 2/3] arm64: dts: ti: k3-j721e-*: Add dts nodes for EHRPWMs
Quoted 34 lines · Rahul T R
From: Vijay Pothukuchi <[email protected]>
Add dts nodes for 6 EHRPWM instances on SoC
Signed-off-by Vijay Pothukuchi <[email protected]>Signed-off-by Rahul T R <[email protected]>--- .../dts/ti/k3-j721e-common-proc-board.dts | 24 +++++++ arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 62 ++++++++++++++++++- arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 24 +++++++ 3 files changed, 109 insertions(+), 1 deletion(-)arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts +14
-0@@ -995,3 +995,27 @@ &main_mcan13 { status = "disabled"; }; + +&main_ehrpwm0 { + status = "disabled"; +}; + +&main_ehrpwm1 { + status = "disabled"; +}; + +&main_ehrpwm2 { + status = "disabled"; +}; + +&main_ehrpwm3 {
arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts line 1021
Quoted 10 lines
arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts +10
-0+ status = "disabled"; +}; + +&main_ehrpwm4 { + status = "disabled"; +}; + +&main_ehrpwm5 { + status = "disabled"; +};
Do the pwm driver croak and die OR it is un-usable on proc-board or disabled due to not-primary function (ideally drivers should shut things off when unused)?
Quoted 12 lines
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +3
-1@@ -66,7 +66,67 @@ #mux-control-cells = <1>; mux-reg-masks = <0x4000 0x8000000>, /* USB0 to SERDES0/3 mux */ <0x4010 0x8000000>; /* USB1 to SERDES1/2 mux */ - }; + }; + + ehrpwm_tbclk: clock-controller@4140 {
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi line 81
Quoted 10 lines
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +10
-0+ compatible = "ti,am654-ehrpwm-tbclk", "syscon"; + reg = <0x4140 0x18>; + #clock-cells = <1>; + }; + }; + + main_ehrpwm0: pwm@3000000 { + compatible = "ti,am654-ehrpwm", "ti,am3352-ehrpwm"; + #pwm-cells = <3>; + reg = <0x0 0x3000000 0x0 0x100>;
would suggest 0x00 instead of 0x0
Quoted 86 lines
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +48
-0+ power-domains = <&k3_pds 83 TI_SCI_PD_EXCLUSIVE>; + clocks = <&ehrpwm_tbclk 0>, <&k3_clks 83 0>; + clock-names = "tbclk", "fck"; + }; + + main_ehrpwm1: pwm@3010000 { + compatible = "ti,am654-ehrpwm", "ti,am3352-ehrpwm"; + #pwm-cells = <3>; + reg = <0x0 0x3010000 0x0 0x100>; + power-domains = <&k3_pds 84 TI_SCI_PD_EXCLUSIVE>; + clocks = <&ehrpwm_tbclk 1>, <&k3_clks 84 0>; + clock-names = "tbclk", "fck"; + }; + + main_ehrpwm2: pwm@3020000 { + compatible = "ti,am654-ehrpwm", "ti,am3352-ehrpwm"; + #pwm-cells = <3>; + reg = <0x0 0x3020000 0x0 0x100>; + power-domains = <&k3_pds 85 TI_SCI_PD_EXCLUSIVE>; + clocks = <&ehrpwm_tbclk 2>, <&k3_clks 85 0>; + clock-names = "tbclk", "fck"; + }; + + main_ehrpwm3: pwm@3030000 { + compatible = "ti,am654-ehrpwm", "ti,am3352-ehrpwm"; + #pwm-cells = <3>; + reg = <0x0 0x3030000 0x0 0x100>; + power-domains = <&k3_pds 86 TI_SCI_PD_EXCLUSIVE>; + clocks = <&ehrpwm_tbclk 3>, <&k3_clks 86 0>; + clock-names = "tbclk", "fck"; + }; + + main_ehrpwm4: pwm@3040000 { + compatible = "ti,am654-ehrpwm", "ti,am3352-ehrpwm"; + #pwm-cells = <3>; + reg = <0x0 0x3040000 0x0 0x100>; + power-domains = <&k3_pds 87 TI_SCI_PD_EXCLUSIVE>; + clocks = <&ehrpwm_tbclk 4>, <&k3_clks 87 0>; + clock-names = "tbclk", "fck"; + }; + + main_ehrpwm5: pwm@3050000 { + compatible = "ti,am654-ehrpwm", "ti,am3352-ehrpwm"; + #pwm-cells = <3>; + reg = <0x0 0x3050000 0x0 0x100>; + power-domains = <&k3_pds 88 TI_SCI_PD_EXCLUSIVE>; + clocks = <&ehrpwm_tbclk 5>, <&k3_clks 88 0>; + clock-names = "tbclk", "fck"; }; gic500: interrupt-controller@1800000 {arch/arm64/boot/dts/ti/k3-j721e-sk.dts +24
-0@@ -1129,3 +1129,27 @@ memory-region = <&c71_0_dma_memory_region>, <&c71_0_memory_region>; }; + +&main_ehrpwm0 { + status = "disabled"; +}; + +&main_ehrpwm1 { + status = "disabled"; +}; + +&main_ehrpwm2 { + status = "disabled"; +}; + +&main_ehrpwm3 { + status = "disabled"; +}; + +&main_ehrpwm4 { + status = "disabled"; +}; + +&main_ehrpwm5 { + status = "disabled"; +};Signature · 1 line
2.17.1
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Re: [PATCH v4 2/3] arm64: dts: ti: k3-j721e-*: Add dts nodes for EHRPWMs
Quoted 42 lines · Nishanth Menon
Quoted 41 lines · Rahul T R
From: Vijay Pothukuchi <[email protected]>
Add dts nodes for 6 EHRPWM instances on SoC
Signed-off-by Vijay Pothukuchi <[email protected]>Signed-off-by Rahul T R <[email protected]>--- .../dts/ti/k3-j721e-common-proc-board.dts | 24 +++++++ arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 62 ++++++++++++++++++- arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 24 +++++++ 3 files changed, 109 insertions(+), 1 deletion(-)arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts +21
-0@@ -995,3 +995,27 @@ &main_mcan13 { status = "disabled"; }; + +&main_ehrpwm0 { + status = "disabled"; +}; + +&main_ehrpwm1 { + status = "disabled"; +}; + +&main_ehrpwm2 { + status = "disabled"; +}; + +&main_ehrpwm3 { + status = "disabled"; +}; + +&main_ehrpwm4 { + status = "disabled"; +}; +
Quoted 9 lines
arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts line 1021
Quoted 3 lines
arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts +3
-0+&main_ehrpwm5 { + status = "disabled"; +};Do the pwm driver croak and die OR it is un-usable on proc-board or disabled due to not-primary function (ideally drivers should shut things off when unused)?
Hi Nishanth,
Nodes are disabled since
EHRPWM is not primary function and pins are configured for different interfaces like MCASP10 etc..
Quoted 16 lines
Quoted 16 lines
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +7
-1@@ -66,7 +66,67 @@ #mux-control-cells = <1>; mux-reg-masks = <0x4000 0x8000000>, /* USB0 to SERDES0/3 mux */ <0x4010 0x8000000>; /* USB1 to SERDES1/2 mux */ - }; + }; + + ehrpwm_tbclk: clock-controller@4140 { + compatible = "ti,am654-ehrpwm-tbclk", "syscon"; + reg = <0x4140 0x18>; + #clock-cells = <1>; + };
Quoted 8 lines
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi line 81
Quoted 6 lines
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +6
-0+ }; + + main_ehrpwm0: pwm@3000000 { + compatible = "ti,am654-ehrpwm", "ti,am3352-ehrpwm"; + #pwm-cells = <3>; + reg = <0x0 0x3000000 0x0 0x100>;would suggest
0x00instead of0x0
will fix this in the respin
Regards
Rahul T R
Quoted 92 lines
Quoted 87 lines
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +48
-0+ power-domains = <&k3_pds 83 TI_SCI_PD_EXCLUSIVE>; + clocks = <&ehrpwm_tbclk 0>, <&k3_clks 83 0>; + clock-names = "tbclk", "fck"; + }; + + main_ehrpwm1: pwm@3010000 { + compatible = "ti,am654-ehrpwm", "ti,am3352-ehrpwm"; + #pwm-cells = <3>; + reg = <0x0 0x3010000 0x0 0x100>; + power-domains = <&k3_pds 84 TI_SCI_PD_EXCLUSIVE>; + clocks = <&ehrpwm_tbclk 1>, <&k3_clks 84 0>; + clock-names = "tbclk", "fck"; + }; + + main_ehrpwm2: pwm@3020000 { + compatible = "ti,am654-ehrpwm", "ti,am3352-ehrpwm"; + #pwm-cells = <3>; + reg = <0x0 0x3020000 0x0 0x100>; + power-domains = <&k3_pds 85 TI_SCI_PD_EXCLUSIVE>; + clocks = <&ehrpwm_tbclk 2>, <&k3_clks 85 0>; + clock-names = "tbclk", "fck"; + }; + + main_ehrpwm3: pwm@3030000 { + compatible = "ti,am654-ehrpwm", "ti,am3352-ehrpwm"; + #pwm-cells = <3>; + reg = <0x0 0x3030000 0x0 0x100>; + power-domains = <&k3_pds 86 TI_SCI_PD_EXCLUSIVE>; + clocks = <&ehrpwm_tbclk 3>, <&k3_clks 86 0>; + clock-names = "tbclk", "fck"; + }; + + main_ehrpwm4: pwm@3040000 { + compatible = "ti,am654-ehrpwm", "ti,am3352-ehrpwm"; + #pwm-cells = <3>; + reg = <0x0 0x3040000 0x0 0x100>; + power-domains = <&k3_pds 87 TI_SCI_PD_EXCLUSIVE>; + clocks = <&ehrpwm_tbclk 4>, <&k3_clks 87 0>; + clock-names = "tbclk", "fck"; + }; + + main_ehrpwm5: pwm@3050000 { + compatible = "ti,am654-ehrpwm", "ti,am3352-ehrpwm"; + #pwm-cells = <3>; + reg = <0x0 0x3050000 0x0 0x100>; + power-domains = <&k3_pds 88 TI_SCI_PD_EXCLUSIVE>; + clocks = <&ehrpwm_tbclk 5>, <&k3_clks 88 0>; + clock-names = "tbclk", "fck"; }; gic500: interrupt-controller@1800000 {arch/arm64/boot/dts/ti/k3-j721e-sk.dts +24
-0@@ -1129,3 +1129,27 @@ memory-region = <&c71_0_dma_memory_region>, <&c71_0_memory_region>; }; + +&main_ehrpwm0 { + status = "disabled"; +}; + +&main_ehrpwm1 { + status = "disabled"; +}; + +&main_ehrpwm2 { + status = "disabled"; +}; + +&main_ehrpwm3 { + status = "disabled"; +}; + +&main_ehrpwm4 { + status = "disabled"; +}; + +&main_ehrpwm5 { + status = "disabled"; +};Signature · 1 line
2.17.1Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
PATCH v4 3/3 arm64: dts: ti: k3-j721e-sk: Add pinmux for RPi Header
In reply to Rahul T RFrom: Sinthu Raja <[email protected]>
Add pinmux required to bring out
i2c5, ehrpwm 2 and 3 and gpios on
40 pin RPi header on sk board
--- arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 89 ++++++++++++++++++++++---- 1 file changed, 78 insertions(+), 11 deletions(-)
arch/arm64/boot/dts/ti/k3-j721e-sk.dts +78 -11
@@ -400,6 +400,57 @@ J721E_IOPAD(0x124, PIN_INPUT, 7) /* (Y24) PRG0_PRU1_GPO9.GPIO0_72 */ >; }; + + main_i2c5_pins_default: main-i2c5-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x150, PIN_INPUT_PULLUP, 2) /* (Y26) PRG0_MDIO0_MDIO.I2C5_SCL */ + J721E_IOPAD(0x154, PIN_INPUT_PULLUP, 2) /* (AA27) PRG0_MDIO0_MDC.I2C5_SDA */ + >; + }; + + rpi_header_gpio0_pins_default: rpi-header-gpio0-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x01c, PIN_INPUT, 7) /* (AD22) PRG1_PRU0_GPO6.GPIO0_7 */ + J721E_IOPAD(0x120, PIN_INPUT, 7) /* (AA28) PRG0_PRU1_GPO8.GPIO0_71 */ + J721E_IOPAD(0x14c, PIN_INPUT, 7) /* (AA29) PRG0_PRU1_GPO19.GPIO0_82 */ + J721E_IOPAD(0x02c, PIN_INPUT, 7) /* (AD21) PRG1_PRU0_GPO10.GPIO0_11 */ + J721E_IOPAD(0x198, PIN_INPUT, 7) /* (V25) RGMII6_TD1.GPIO0_101 */ + J721E_IOPAD(0x1b0, PIN_INPUT, 7) /* (W24) RGMII6_RD1.GPIO0_107 */ + J721E_IOPAD(0x1a0, PIN_INPUT, 7) /* (W29) RGMII6_TXC.GPIO0_103 */ + J721E_IOPAD(0x008, PIN_INPUT, 7) /* (AG22) PRG1_PRU0_GPO1.GPIO0_2 */ + J721E_IOPAD(0x1d0, PIN_INPUT, 7) /* (AA3) SPI0_D1.GPIO0_115 */ + J721E_IOPAD(0x11c, PIN_INPUT, 7) /* (AA24) PRG0_PRU1_GPO7.GPIO0_70 */ + J721E_IOPAD(0x148, PIN_INPUT, 7) /* (AA26) PRG0_PRU1_GPO18.GPIO0_81 */ + J721E_IOPAD(0x004, PIN_INPUT, 7) /* (AC23) PRG1_PRU0_GPO0.GPIO0_1 */ + J721E_IOPAD(0x014, PIN_INPUT, 7) /* (AH23) PRG1_PRU0_GPO4.GPIO0_5 */ + J721E_IOPAD(0x020, PIN_INPUT, 7) /* (AE20) PRG1_PRU0_GPO7.GPIO0_8 */ + J721E_IOPAD(0x19c, PIN_INPUT, 7) /* (W27) RGMII6_TD0.GPIO0_102 */ + J721E_IOPAD(0x1b4, PIN_INPUT, 7) /* (W25) RGMII6_RD0.GPIO0_108 */ + J721E_IOPAD(0x188, PIN_INPUT, 7) /* (Y28) RGMII6_TX_CTL.GPIO0_97 */ + J721E_IOPAD(0x00c, PIN_INPUT, 7) /* (AF22) PRG1_PRU0_GPO2.GPIO0_3 */ + J721E_IOPAD(0x010, PIN_INPUT, 7) /* (AJ23) PRG1_PRU0_GPO3.GPIO0_4 */ + >; + }; + + rpi_header_gpio1_pins_default: rpi-header-gpio1-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x234, PIN_INPUT, 7) /* (U3) EXT_REFCLK1.GPIO1_12 */ + >; + }; + + rpi_header_ehrpwm2_pins_default: rpi-header-ehrpwm2-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x178, PIN_INPUT, 6) /* (U27) RGMII5_RD3.EHRPWM2_A */ + J721E_IOPAD(0x17c, PIN_INPUT, 6) /* (U24) RGMII5_RD2.EHRPWM2_B */ + >; + }; + + rpi_header_ehrpwm3_pins_default: rpi-header-ehrpwm3-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x18c, PIN_INPUT, 6) /* (V23) RGMII6_RX_CTL.EHRPWM3_A */ + J721E_IOPAD(0x190, PIN_INPUT, 6) /* (W23) RGMII6_TD3.EHRPWM3_B */ + >; + }; }; &wkup_pmx0 {
@@ -631,11 +682,6 @@ status = "disabled"; }; -&main_i2c5 { - /* Brought out on RPi Header */ - status = "disabled"; -}; - &main_i2c6 { /* Unused */ status = "disabled";
@@ -1138,18 +1184,39 @@ status = "disabled"; }; -&main_ehrpwm2 { +&main_ehrpwm4 { status = "disabled"; }; -&main_ehrpwm3 { +&main_ehrpwm5 { status = "disabled"; }; -&main_ehrpwm4 { - status = "disabled"; +&main_gpio0 { + pinctrl-names = "default"; + pinctrl-0 = <&rpi_header_gpio0_pins_default>; }; -&main_ehrpwm5 { - status = "disabled"; +&main_gpio1 { + pinctrl-names = "default"; + pinctrl-0 = <&rpi_header_gpio1_pins_default>; +}; + +&main_i2c5 { + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c5_pins_default>; + clock-frequency = <400000>; + status = "okay"; +}; + +&main_ehrpwm2 { + pinctrl-names = "default"; + pinctrl-0 = <&rpi_header_ehrpwm2_pins_default>; + status = "okay"; +}; + +&main_ehrpwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&rpi_header_ehrpwm3_pins_default>; + status = "okay"; };
Signature · 1 line
2.17.1
Nishanth Menon
maintainerRe: [PATCH v4 3/3] arm64: dts: ti: k3-j721e-sk: Add pinmux for RPi Header
Quoted 8 lines · Rahul T R
From: Sinthu Raja <[email protected]>
Add pinmux required to bring out
i2c5, ehrpwm 2 and 3 and gpios on
40 pin RPi header on sk boardSigned-off-by Sinthu Raja <[email protected]>Signed-off-by Rahul T R <[email protected]>
I was digging deeper at https://www.ti.com/lit/zip/sprr438
(PROC112E2(001)_SCH.pdf - J3, Also looking at
https://github.com/beagleboard/beaglebone-ai-64/blob/master/BeagleBone%20AI%20-64_SCH_V1.02_211119.pdf
(P8, P9)
And comparing it to https://www.raspberrypi-spy.co.uk/2012/06/simple-guide-to-the-rpi-gpio-header-and-pins/
And considering potential use such as https://pypi.org/project/RPi.GPIO/
variation,
Here is my suggestion (applies to other TI Boards that attempt to emulate RPI header)
a) Default mux in board.dts should be GPIO except for the i2c used for ID detection.
b) Secondary functions should be a dt overlay. (These can easily enable the pwms and other functions as needed)
c) Maintain node names consistent to allow reuse of overlays across platforms.
Usage: you can either use extlinux.conf OR uEnv.txt to apply the overlays as desired (ID detection from hats might help automate it based on the bootloader you'd want to use)
Else, you have created a custom configuration here for 1 specific application, various hats that expect GPIO will end up croaking.
I am open to discussions here.
Quoted 67 lines
--- arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 89 ++++++++++++++++++++++---- 1 file changed, 78 insertions(+), 11 deletions(-)arch/arm64/boot/dts/ti/k3-j721e-sk.dts +51
-0@@ -400,6 +400,57 @@ J721E_IOPAD(0x124, PIN_INPUT, 7) /* (Y24) PRG0_PRU1_GPO9.GPIO0_72 */ >; }; + + main_i2c5_pins_default: main-i2c5-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x150, PIN_INPUT_PULLUP, 2) /* (Y26) PRG0_MDIO0_MDIO.I2C5_SCL */ + J721E_IOPAD(0x154, PIN_INPUT_PULLUP, 2) /* (AA27) PRG0_MDIO0_MDC.I2C5_SDA */ + >; + }; + + rpi_header_gpio0_pins_default: rpi-header-gpio0-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x01c, PIN_INPUT, 7) /* (AD22) PRG1_PRU0_GPO6.GPIO0_7 */ + J721E_IOPAD(0x120, PIN_INPUT, 7) /* (AA28) PRG0_PRU1_GPO8.GPIO0_71 */ + J721E_IOPAD(0x14c, PIN_INPUT, 7) /* (AA29) PRG0_PRU1_GPO19.GPIO0_82 */ + J721E_IOPAD(0x02c, PIN_INPUT, 7) /* (AD21) PRG1_PRU0_GPO10.GPIO0_11 */ + J721E_IOPAD(0x198, PIN_INPUT, 7) /* (V25) RGMII6_TD1.GPIO0_101 */ + J721E_IOPAD(0x1b0, PIN_INPUT, 7) /* (W24) RGMII6_RD1.GPIO0_107 */ + J721E_IOPAD(0x1a0, PIN_INPUT, 7) /* (W29) RGMII6_TXC.GPIO0_103 */ + J721E_IOPAD(0x008, PIN_INPUT, 7) /* (AG22) PRG1_PRU0_GPO1.GPIO0_2 */ + J721E_IOPAD(0x1d0, PIN_INPUT, 7) /* (AA3) SPI0_D1.GPIO0_115 */ + J721E_IOPAD(0x11c, PIN_INPUT, 7) /* (AA24) PRG0_PRU1_GPO7.GPIO0_70 */ + J721E_IOPAD(0x148, PIN_INPUT, 7) /* (AA26) PRG0_PRU1_GPO18.GPIO0_81 */ + J721E_IOPAD(0x004, PIN_INPUT, 7) /* (AC23) PRG1_PRU0_GPO0.GPIO0_1 */ + J721E_IOPAD(0x014, PIN_INPUT, 7) /* (AH23) PRG1_PRU0_GPO4.GPIO0_5 */ + J721E_IOPAD(0x020, PIN_INPUT, 7) /* (AE20) PRG1_PRU0_GPO7.GPIO0_8 */ + J721E_IOPAD(0x19c, PIN_INPUT, 7) /* (W27) RGMII6_TD0.GPIO0_102 */ + J721E_IOPAD(0x1b4, PIN_INPUT, 7) /* (W25) RGMII6_RD0.GPIO0_108 */ + J721E_IOPAD(0x188, PIN_INPUT, 7) /* (Y28) RGMII6_TX_CTL.GPIO0_97 */ + J721E_IOPAD(0x00c, PIN_INPUT, 7) /* (AF22) PRG1_PRU0_GPO2.GPIO0_3 */ + J721E_IOPAD(0x010, PIN_INPUT, 7) /* (AJ23) PRG1_PRU0_GPO3.GPIO0_4 */ + >; + }; + + rpi_header_gpio1_pins_default: rpi-header-gpio1-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x234, PIN_INPUT, 7) /* (U3) EXT_REFCLK1.GPIO1_12 */ + >; + }; + + rpi_header_ehrpwm2_pins_default: rpi-header-ehrpwm2-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x178, PIN_INPUT, 6) /* (U27) RGMII5_RD3.EHRPWM2_A */ + J721E_IOPAD(0x17c, PIN_INPUT, 6) /* (U24) RGMII5_RD2.EHRPWM2_B */ + >; + }; + + rpi_header_ehrpwm3_pins_default: rpi-header-ehrpwm3-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x18c, PIN_INPUT, 6) /* (V23) RGMII6_RX_CTL.EHRPWM3_A */ + J721E_IOPAD(0x190, PIN_INPUT, 6) /* (W23) RGMII6_TD3.EHRPWM3_B */ + >; + }; }; &wkup_pmx0 {
arch/arm64/boot/dts/ti/k3-j721e-sk.dts line 638
Quoted 8 lines
arch/arm64/boot/dts/ti/k3-j721e-sk.dts +0
-5@@ -631,11 +682,6 @@ status = "disabled"; }; -&main_i2c5 { - /* Brought out on RPi Header */ - status = "disabled"; -}; -
Please don't relocate nodes in the same patch - kinda messes up the diffstat and makes review a bit harder.
Quoted 26 lines
arch/arm64/boot/dts/ti/k3-j721e-sk.dts +5
-6&main_i2c6 { /* Unused */ status = "disabled";@@ -1138,18 +1184,39 @@ status = "disabled"; }; -&main_ehrpwm2 { +&main_ehrpwm4 { status = "disabled"; }; -&main_ehrpwm3 { +&main_ehrpwm5 { status = "disabled"; }; -&main_ehrpwm4 { - status = "disabled"; +&main_gpio0 { + pinctrl-names = "default"; + pinctrl-0 = <&rpi_header_gpio0_pins_default>; }; -&main_ehrpwm5 { - status = "disabled";
arch/arm64/boot/dts/ti/k3-j721e-sk.dts line 1209
Quoted 10 lines
arch/arm64/boot/dts/ti/k3-j721e-sk.dts +10
-0+&main_gpio1 { + pinctrl-names = "default"; + pinctrl-0 = <&rpi_header_gpio1_pins_default>; +}; + +&main_i2c5 { + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c5_pins_default>; + clock-frequency = <400000>; + status = "okay";
Defaults in SoC.dtsi so far are "okay" - so adding that again is superfluous This happens when you are relocating nodes etc
Quoted 13 lines
arch/arm64/boot/dts/ti/k3-j721e-sk.dts +12
-0+}; + +&main_ehrpwm2 { + pinctrl-names = "default"; + pinctrl-0 = <&rpi_header_ehrpwm2_pins_default>; + status = "okay"; +}; + +&main_ehrpwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&rpi_header_ehrpwm3_pins_default>; + status = "okay"; };
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Re: [PATCH v4 3/3] arm64: dts: ti: k3-j721e-sk: Add pinmux for RPi Header
For those seeing this message multiple times, my apologies for not properly setting up my mailer.
Quoted 34 lines · Nishanth Menon
Quoted 8 lines · Rahul T R
From: Sinthu Raja <[email protected]>
Add pinmux required to bring out
i2c5, ehrpwm 2 and 3 and gpios on
40 pin RPi header on sk boardSigned-off-by Sinthu Raja <[email protected]>Signed-off-by Rahul T R <[email protected]>I was digging deeper at https://www.ti.com/lit/zip/sprr438
(PROC112E2(001)_SCH.pdf - J3, Also looking at
https://github.com/beagleboard/beaglebone-ai-64/blob/master/BeagleBone%20AI%20-64_SCH_V1.02_211119.pdf
(P8, P9)And comparing it to https://www.raspberrypi-spy.co.uk/2012/06/simple-guide-to-the-rpi-gpio-header-and-pins/
And considering potential use such as https://pypi.org/project/RPi.GPIO/
variation,Here is my suggestion (applies to other TI Boards that attempt to emulate RPI header)
a) Default mux inboard.dtsshould be GPIO except for the i2c used for ID detection.
b) Secondary functions should be a dt overlay. (These can easily enable the pwms and other functions as needed)
c) Maintain node names consistent to allow reuse of overlays across platforms.Usage: you can either use extlinux.conf OR uEnv.txt to apply the overlays as desired (ID detection from hats might help automate it based on the bootloader you'd want to use)
Quoted 5 lines
Else, you have created a custom configuration here for 1 specific application, various hats that expect GPIO will end up croaking.
I am open to discussions here.
A read of our recent blog series done with Bootlin is worth a read on this topic. https://bbb.io/@2804
My suggestion is to put the entries for the common functions in the base tree, but not enable them (except for the I2C used for ID detection, as you suggested). This can remove SoC-specific requirements on the overlays such that the overlays are written against a header specification as defined by the common symbols provided. So, make the entries in the base tree and leave them "disabled" such that overlays only need to set the symbol to "okay", at least for the common stuff to all implementations of the Pi header.
Quoted 139 lines
Quoted 69 lines
--- arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 89 ++++++++++++++++++++++---- 1 file changed, 78 insertions(+), 11 deletions(-)arch/arm64/boot/dts/ti/k3-j721e-sk.dts +51
-0@@ -400,6 +400,57 @@ J721E_IOPAD(0x124, PIN_INPUT, 7) /* (Y24) PRG0_PRU1_GPO9.GPIO0_72 */ >; }; + + main_i2c5_pins_default: main-i2c5-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x150, PIN_INPUT_PULLUP, 2) /* (Y26) PRG0_MDIO0_MDIO.I2C5_SCL */ + J721E_IOPAD(0x154, PIN_INPUT_PULLUP, 2) /* (AA27) PRG0_MDIO0_MDC.I2C5_SDA */ + >; + }; + + rpi_header_gpio0_pins_default: rpi-header-gpio0-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x01c, PIN_INPUT, 7) /* (AD22) PRG1_PRU0_GPO6.GPIO0_7 */ + J721E_IOPAD(0x120, PIN_INPUT, 7) /* (AA28) PRG0_PRU1_GPO8.GPIO0_71 */ + J721E_IOPAD(0x14c, PIN_INPUT, 7) /* (AA29) PRG0_PRU1_GPO19.GPIO0_82 */ + J721E_IOPAD(0x02c, PIN_INPUT, 7) /* (AD21) PRG1_PRU0_GPO10.GPIO0_11 */ + J721E_IOPAD(0x198, PIN_INPUT, 7) /* (V25) RGMII6_TD1.GPIO0_101 */ + J721E_IOPAD(0x1b0, PIN_INPUT, 7) /* (W24) RGMII6_RD1.GPIO0_107 */ + J721E_IOPAD(0x1a0, PIN_INPUT, 7) /* (W29) RGMII6_TXC.GPIO0_103 */ + J721E_IOPAD(0x008, PIN_INPUT, 7) /* (AG22) PRG1_PRU0_GPO1.GPIO0_2 */ + J721E_IOPAD(0x1d0, PIN_INPUT, 7) /* (AA3) SPI0_D1.GPIO0_115 */ + J721E_IOPAD(0x11c, PIN_INPUT, 7) /* (AA24) PRG0_PRU1_GPO7.GPIO0_70 */ + J721E_IOPAD(0x148, PIN_INPUT, 7) /* (AA26) PRG0_PRU1_GPO18.GPIO0_81 */ + J721E_IOPAD(0x004, PIN_INPUT, 7) /* (AC23) PRG1_PRU0_GPO0.GPIO0_1 */ + J721E_IOPAD(0x014, PIN_INPUT, 7) /* (AH23) PRG1_PRU0_GPO4.GPIO0_5 */ + J721E_IOPAD(0x020, PIN_INPUT, 7) /* (AE20) PRG1_PRU0_GPO7.GPIO0_8 */ + J721E_IOPAD(0x19c, PIN_INPUT, 7) /* (W27) RGMII6_TD0.GPIO0_102 */ + J721E_IOPAD(0x1b4, PIN_INPUT, 7) /* (W25) RGMII6_RD0.GPIO0_108 */ + J721E_IOPAD(0x188, PIN_INPUT, 7) /* (Y28) RGMII6_TX_CTL.GPIO0_97 */ + J721E_IOPAD(0x00c, PIN_INPUT, 7) /* (AF22) PRG1_PRU0_GPO2.GPIO0_3 */ + J721E_IOPAD(0x010, PIN_INPUT, 7) /* (AJ23) PRG1_PRU0_GPO3.GPIO0_4 */ + >; + }; + + rpi_header_gpio1_pins_default: rpi-header-gpio1-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x234, PIN_INPUT, 7) /* (U3) EXT_REFCLK1.GPIO1_12 */ + >; + }; + + rpi_header_ehrpwm2_pins_default: rpi-header-ehrpwm2-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x178, PIN_INPUT, 6) /* (U27) RGMII5_RD3.EHRPWM2_A */ + J721E_IOPAD(0x17c, PIN_INPUT, 6) /* (U24) RGMII5_RD2.EHRPWM2_B */ + >; + }; + + rpi_header_ehrpwm3_pins_default: rpi-header-ehrpwm3-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x18c, PIN_INPUT, 6) /* (V23) RGMII6_RX_CTL.EHRPWM3_A */ + J721E_IOPAD(0x190, PIN_INPUT, 6) /* (W23) RGMII6_TD3.EHRPWM3_B */ + >; + }; }; &wkup_pmx0 {arch/arm64/boot/dts/ti/k3-j721e-sk.dts line 638
Quoted 8 lines
arch/arm64/boot/dts/ti/k3-j721e-sk.dts +0
-5@@ -631,11 +682,6 @@ status = "disabled"; }; -&main_i2c5 { - /* Brought out on RPi Header */ - status = "disabled"; -}; -Please don't relocate nodes in the same patch - kinda messes up the diffstat and makes review a bit harder.
Quoted 26 lines
arch/arm64/boot/dts/ti/k3-j721e-sk.dts +5
-6&main_i2c6 { /* Unused */ status = "disabled";@@ -1138,18 +1184,39 @@ status = "disabled"; }; -&main_ehrpwm2 { +&main_ehrpwm4 { status = "disabled"; }; -&main_ehrpwm3 { +&main_ehrpwm5 { status = "disabled"; }; -&main_ehrpwm4 { - status = "disabled"; +&main_gpio0 { + pinctrl-names = "default"; + pinctrl-0 = <&rpi_header_gpio0_pins_default>; }; -&main_ehrpwm5 { - status = "disabled";arch/arm64/boot/dts/ti/k3-j721e-sk.dts line 1209
Quoted 10 lines
arch/arm64/boot/dts/ti/k3-j721e-sk.dts +10
-0+&main_gpio1 { + pinctrl-names = "default"; + pinctrl-0 = <&rpi_header_gpio1_pins_default>; +}; + +&main_i2c5 { + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c5_pins_default>; + clock-frequency = <400000>; + status = "okay";Defaults in
SoC.dtsiso far are "okay" - so adding that again is superfluous This happens when you are relocating nodes etcarch/arm64/boot/dts/ti/k3-j721e-sk.dts line 1222
Quoted 13 lines
arch/arm64/boot/dts/ti/k3-j721e-sk.dts +12
-0+}; + +&main_ehrpwm2 { + pinctrl-names = "default"; + pinctrl-0 = <&rpi_header_ehrpwm2_pins_default>; + status = "okay"; +}; + +&main_ehrpwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&rpi_header_ehrpwm3_pins_default>; + status = "okay"; };--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Signature · 2 lines
https://beagleboard.org/about/jkridner - a 501c3 non-profit educating around open hardware computing
Re: [PATCH v4 3/3] arm64: dts: ti: k3-j721e-sk: Add pinmux for RPi Header
Quoted 49 lines · Jason Kridner
For those seeing this message multiple times, my apologies for not properly setting up my mailer.
Quoted 34 lines · Nishanth Menon
Quoted 8 lines · Rahul T R
From: Sinthu Raja <[email protected]>
Add pinmux required to bring out
i2c5, ehrpwm 2 and 3 and gpios on
40 pin RPi header on sk boardSigned-off-by Sinthu Raja <[email protected]>Signed-off-by Rahul T R <[email protected]>I was digging deeper at https://www.ti.com/lit/zip/sprr438
(PROC112E2(001)_SCH.pdf - J3, Also looking at
https://github.com/beagleboard/beaglebone-ai-64/blob/master/BeagleBone%20AI%20-64_SCH_V1.02_211119.pdf
(P8, P9)And comparing it to https://www.raspberrypi-spy.co.uk/2012/06/simple-guide-to-the-rpi-gpio-header-and-pins/
And considering potential use such as https://pypi.org/project/RPi.GPIO/
variation,Here is my suggestion (applies to other TI Boards that attempt to emulate RPI header)
a) Default mux inboard.dtsshould be GPIO except for the i2c used for ID detection.
b) Secondary functions should be a dt overlay. (These can easily enable the pwms and other functions as needed)
c) Maintain node names consistent to allow reuse of overlays across platforms.Usage: you can either use extlinux.conf OR uEnv.txt to apply the overlays as desired (ID detection from hats might help automate it based on the bootloader you'd want to use)
Quoted 5 lines
Else, you have created a custom configuration here for 1 specific application, various hats that expect GPIO will end up croaking.
I am open to discussions here.
A read of our recent blog series done with Bootlin is worth a read on this topic. https://bbb.io/@2804
Quoted 9 lines
My suggestion is to put the entries for the common functions in the base tree, but not enable them (except for the I2C used for ID detection, as you suggested). This can remove SoC-specific requirements on the overlays such that the overlays are written against a header specification as defined by the common symbols provided. So, make the entries in the base tree and leave them "disabled" such that overlays only need to set the symbol to "okay", at least for the common stuff to all implementations of the Pi header.
Hi Nishanth, Jason,
I agree for enabling only gpio's in the base dts and create overlays based on the specific use case
We cannot create separate overlays for each functionality since the pimux varies based on the combination of functions enabled
Ex: pinmux for gpio will be different between enabling only pwm and enabling pwm + spi
When we create a overlay, along with setting
the status to okay, we need to take care of
configuring right pinmux as well
I will send a respin with enabling only gpio
Quoted 73 lines
Quoted 73 lines
Quoted 73 lines
--- arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 89 ++++++++++++++++++++++---- 1 file changed, 78 insertions(+), 11 deletions(-)arch/arm64/boot/dts/ti/k3-j721e-sk.dts +51
-0@@ -400,6 +400,57 @@ J721E_IOPAD(0x124, PIN_INPUT, 7) /* (Y24) PRG0_PRU1_GPO9.GPIO0_72 */ >; }; + + main_i2c5_pins_default: main-i2c5-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x150, PIN_INPUT_PULLUP, 2) /* (Y26) PRG0_MDIO0_MDIO.I2C5_SCL */ + J721E_IOPAD(0x154, PIN_INPUT_PULLUP, 2) /* (AA27) PRG0_MDIO0_MDC.I2C5_SDA */ + >; + }; + + rpi_header_gpio0_pins_default: rpi-header-gpio0-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x01c, PIN_INPUT, 7) /* (AD22) PRG1_PRU0_GPO6.GPIO0_7 */ + J721E_IOPAD(0x120, PIN_INPUT, 7) /* (AA28) PRG0_PRU1_GPO8.GPIO0_71 */ + J721E_IOPAD(0x14c, PIN_INPUT, 7) /* (AA29) PRG0_PRU1_GPO19.GPIO0_82 */ + J721E_IOPAD(0x02c, PIN_INPUT, 7) /* (AD21) PRG1_PRU0_GPO10.GPIO0_11 */ + J721E_IOPAD(0x198, PIN_INPUT, 7) /* (V25) RGMII6_TD1.GPIO0_101 */ + J721E_IOPAD(0x1b0, PIN_INPUT, 7) /* (W24) RGMII6_RD1.GPIO0_107 */ + J721E_IOPAD(0x1a0, PIN_INPUT, 7) /* (W29) RGMII6_TXC.GPIO0_103 */ + J721E_IOPAD(0x008, PIN_INPUT, 7) /* (AG22) PRG1_PRU0_GPO1.GPIO0_2 */ + J721E_IOPAD(0x1d0, PIN_INPUT, 7) /* (AA3) SPI0_D1.GPIO0_115 */ + J721E_IOPAD(0x11c, PIN_INPUT, 7) /* (AA24) PRG0_PRU1_GPO7.GPIO0_70 */ + J721E_IOPAD(0x148, PIN_INPUT, 7) /* (AA26) PRG0_PRU1_GPO18.GPIO0_81 */ + J721E_IOPAD(0x004, PIN_INPUT, 7) /* (AC23) PRG1_PRU0_GPO0.GPIO0_1 */ + J721E_IOPAD(0x014, PIN_INPUT, 7) /* (AH23) PRG1_PRU0_GPO4.GPIO0_5 */ + J721E_IOPAD(0x020, PIN_INPUT, 7) /* (AE20) PRG1_PRU0_GPO7.GPIO0_8 */ + J721E_IOPAD(0x19c, PIN_INPUT, 7) /* (W27) RGMII6_TD0.GPIO0_102 */ + J721E_IOPAD(0x1b4, PIN_INPUT, 7) /* (W25) RGMII6_RD0.GPIO0_108 */ + J721E_IOPAD(0x188, PIN_INPUT, 7) /* (Y28) RGMII6_TX_CTL.GPIO0_97 */ + J721E_IOPAD(0x00c, PIN_INPUT, 7) /* (AF22) PRG1_PRU0_GPO2.GPIO0_3 */ + J721E_IOPAD(0x010, PIN_INPUT, 7) /* (AJ23) PRG1_PRU0_GPO3.GPIO0_4 */ + >; + }; + + rpi_header_gpio1_pins_default: rpi-header-gpio1-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x234, PIN_INPUT, 7) /* (U3) EXT_REFCLK1.GPIO1_12 */ + >; + }; + + rpi_header_ehrpwm2_pins_default: rpi-header-ehrpwm2-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x178, PIN_INPUT, 6) /* (U27) RGMII5_RD3.EHRPWM2_A */ + J721E_IOPAD(0x17c, PIN_INPUT, 6) /* (U24) RGMII5_RD2.EHRPWM2_B */ + >; + }; + + rpi_header_ehrpwm3_pins_default: rpi-header-ehrpwm3-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x18c, PIN_INPUT, 6) /* (V23) RGMII6_RX_CTL.EHRPWM3_A */ + J721E_IOPAD(0x190, PIN_INPUT, 6) /* (W23) RGMII6_TD3.EHRPWM3_B */ + >; + }; }; &wkup_pmx0 {@@ -631,11 +682,6 @@ status = "disabled"; };
Quoted 9 lines
Quoted 9 lines
arch/arm64/boot/dts/ti/k3-j721e-sk.dts line 638
Quoted 5 lines
arch/arm64/boot/dts/ti/k3-j721e-sk.dts +0
-5-&main_i2c5 { - /* Brought out on RPi Header */ - status = "disabled"; -}; -Please don't relocate nodes in the same patch - kinda messes up the diffstat and makes review a bit harder.
will fix this in the respin
Regards
Rahul T R
Quoted 64 lines
Quoted 58 lines
Quoted 26 lines
arch/arm64/boot/dts/ti/k3-j721e-sk.dts +5
-6&main_i2c6 { /* Unused */ status = "disabled";@@ -1138,18 +1184,39 @@ status = "disabled"; }; -&main_ehrpwm2 { +&main_ehrpwm4 { status = "disabled"; }; -&main_ehrpwm3 { +&main_ehrpwm5 { status = "disabled"; }; -&main_ehrpwm4 { - status = "disabled"; +&main_gpio0 { + pinctrl-names = "default"; + pinctrl-0 = <&rpi_header_gpio0_pins_default>; }; -&main_ehrpwm5 { - status = "disabled";arch/arm64/boot/dts/ti/k3-j721e-sk.dts line 1209
Quoted 10 lines
arch/arm64/boot/dts/ti/k3-j721e-sk.dts +10
-0+&main_gpio1 { + pinctrl-names = "default"; + pinctrl-0 = <&rpi_header_gpio1_pins_default>; +}; + +&main_i2c5 { + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c5_pins_default>; + clock-frequency = <400000>; + status = "okay";Defaults in
SoC.dtsiso far are "okay" - so adding that again is superfluous This happens when you are relocating nodes etcarch/arm64/boot/dts/ti/k3-j721e-sk.dts line 1222
Quoted 13 lines
arch/arm64/boot/dts/ti/k3-j721e-sk.dts +12
-0+}; + +&main_ehrpwm2 { + pinctrl-names = "default"; + pinctrl-0 = <&rpi_header_ehrpwm2_pins_default>; + status = "okay"; +}; + +&main_ehrpwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&rpi_header_ehrpwm3_pins_default>; + status = "okay"; };--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249DSignature · 2 lines
https://beagleboard.org/about/jkridner - a 501c3 non-profit educating around open hardware computing