Add support for MediaTek AHCI SATA

index 363fc53..488c937 100644
@@ -153,6 +153,16 @@ config AHCI_CEVA
 
 	  If unsure, say N.
 
+config AHCI_MTK
+	tristate "MediaTek AHCI SATA support"
+	depends on ARCH_MEDIATEK
+	select MFD_SYSCON
+	help
+	  This option enables support for the MediaTek SoC's
+	  onboard AHCI SATA controller.
+
+	  If unsure, say N.
+
 config AHCI_MVEBU
 	tristate "Marvell EBU AHCI SATA support"
 	depends on ARCH_MVEBU

index a26ef5a..ff9cd2e 100644
@@ -17,6 +17,7 @@ obj-$(CONFIG_AHCI_CEVA)		+= ahci_ceva.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_DA850)	+= ahci_da850.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_DM816)	+= ahci_dm816.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_IMX)		+= ahci_imx.o libahci.o libahci_platform.o
+obj-$(CONFIG_AHCI_MTK)		+= ahci_mtk.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_MVEBU)	+= ahci_mvebu.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_OCTEON)	+= ahci_octeon.o
 obj-$(CONFIG_AHCI_SUNXI)	+= ahci_sunxi.o libahci.o libahci_platform.o

new file mode 100644
index 0000000..d2aa696
@@ -0,0 +1,51 @@
+MediaTek Serial ATA controller
+
+Required properties:
+ - compatible	   : Must be "mediatek,<chip>-ahci", "mediatek,mtk-ahci".
+		     When using "mediatek,mtk-ahci" compatible strings, you
+		     need SoC specific ones in addition, one of:
+		     - "mediatek,mt7622-ahci"
+ - reg		   : Physical base addresses and length of register sets.
+ - interrupts	   : Interrupt associated with the SATA device.
+ - interrupt-names : Associated name must be: "hostc".
+ - clocks	   : A list of phandle and clock specifier pairs, one for each
+		     entry in clock-names.
+ - clock-names	   : Associated names must be: "ahb", "axi", "asic", "rbc", "pm".
+ - phys		   : A phandle and PHY specifier pair for the PHY port.
+ - phy-names	   : Associated name must be: "sata-phy".
+ - ports-implemented : See ./ahci-platform.txt for details.
+
+Optional properties:
+ - power-domains   : A phandle and power domain specifier pair to the power
+		     domain which is responsible for collapsing and restoring
+		     power to the peripheral.
+ - resets	   : Must contain an entry for each entry in reset-names.
+		     See ../reset/reset.txt for details.
+ - reset-names	   : Associated names must be: "axi", "sw", "reg".
+ - mediatek,phy-mode : A phandle to the system controller, used to enable
+		       SATA function.
+
+Example:
+
+	sata: sata@1a200000 {
+		compatible = "mediatek,mt7622-ahci",
+			     "mediatek,mtk-ahci";
+		reg = <0 0x1a200000 0 0x1100>;
+		interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "hostc";
+		clocks = <&pciesys CLK_SATA_AHB_EN>,
+			 <&pciesys CLK_SATA_AXI_EN>,
+			 <&pciesys CLK_SATA_ASIC_EN>,
+			 <&pciesys CLK_SATA_RBC_EN>,
+			 <&pciesys CLK_SATA_PM_EN>;
+		clock-names = "ahb", "axi", "asic", "rbc", "pm";
+		phys = <&u3port1 PHY_TYPE_SATA>;
+		phy-names = "sata-phy";
+		ports-implemented = <0x1>;
+		power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>;
+		resets = <&pciesys MT7622_SATA_AXI_BUS_RST>,
+			 <&pciesys MT7622_SATA_PHY_SW_RST>,
+			 <&pciesys MT7622_SATA_PHY_REG_RST>;
+		reset-names = "axi", "sw", "reg";
+		mediatek,phy-mode = <&pciesys>;
+	};