Turris Omnia LED driver changes
Subsystems (4)
Marek Behún
maintainerv3 cover Turris Omnia LED driver changes
Hello Lee,
this is v3 of Turris Omnia LED driver changes.
v1 and v2 can be found at
https://lore.kernel.org/linux-leds/[email protected]/
https://lore.kernel.org/linux-leds/[email protected]/
This series is for 6.12 (alternatively 6.13), but it depends on changes that have been merged to 6.11-rc3. Your for-leds-next branch is based on 6.11-rc1, so it won't apply there.
Changes since v2:
- added interrupts property description to device-tree binding to fix the device-tree binding check reported by Rob's bot (new patch 05/11 in this series)
- dropped the patch that converted to 100 column wrapping, as suggested by Arnd
- took Andy's suggestions into the patch that converts to dev_err_probe()
Marek
Marek Behún (11):
turris-omnia-mcu-interface.h: Move command execution function to
global header
leds: turris-omnia: Use command execution functions from the MCU
driver
turris-omnia-mcu-interface.h: Add LED commands related definitions to
global header
leds: turris-omnia: Use global header for MCU command definitions
dt-bindings: leds: cznic,turris-omnia-leds: Allow interrupts property
leds: turris-omnia: Notify sysfs on MCU global LEDs brightness change
platform: cznic: turris-omnia-mcu: Inform about missing LED panel
brightness change interrupt feature
leds: turris-omnia: Inform about missing LED gamma correction feature
in the MCU driver
leds: turris-omnia: Use dev_err_probe() where appropriate
leds: turris-omnia: Use uppercase first letter in all comments
ARM: dts: turris-omnia: Add global LED brightness change interrupt
.../leds/cznic,turris-omnia-leds.yaml | 8 + .../dts/marvell/armada-385-turris-omnia.dts | 1 + drivers/leds/leds-turris-omnia.c | 262 +++++++----------- .../platform/cznic/turris-omnia-mcu-base.c | 3 + drivers/platform/cznic/turris-omnia-mcu.h | 130 --------- include/linux/turris-omnia-mcu-interface.h | 148 +++++++++- 6 files changed, 258 insertions(+), 294 deletions(-)
Signature · 1 line
2.44.2
Marek Behún
maintainerPATCH v3 1/11 turris-omnia-mcu-interface.h: Move command execution function to global header
Move the command execution functions from the turris-omnia-mcu platform driver private header to the global turris-omnia-mcu-interface.h header, so that they can be used by the LED driver.
--- .../platform/cznic/turris-omnia-mcu-base.c | 1 + drivers/platform/cznic/turris-omnia-mcu.h | 130 ----------------- include/linux/turris-omnia-mcu-interface.h | 136 +++++++++++++++++- 3 files changed, 136 insertions(+), 131 deletions(-)
drivers/platform/cznic/turris-omnia-mcu-base.c +1 -0
@@ -52,6 +52,7 @@ int omnia_cmd_write_read(const struct i2c_client *client,return 0 ; } +EXPORT_SYMBOL_GPL (omnia_cmd_write_read);static int omnia_get_version_hash (struct omnia_mcu *mcu,bool bootloader,char version[static OMNIA_FW_VERSION_HEX_LEN ])
drivers/platform/cznic/turris-omnia-mcu.h +0 -130
148 lines not on this page · raw message
include/linux/turris-omnia-mcu-interface.h +135 -1
146 lines not on this page · raw message
Signature · 1 line
2.44.2
Marek Behún
maintainerPATCH v3 2/11 leds: turris-omnia: Use command execution functions from the MCU driver
In reply to Marek BehúnUse the MCU command execution functions from the MCU driver instead of the ad-hoc implementation in the LED driver. This allows as to drop the LED driver implementation, which is a duplicate.
--- drivers/leds/leds-turris-omnia.c | 110 ++++++++----------------------- 1 file changed, 29 insertions(+), 81 deletions(-)
drivers/leds/leds-turris-omnia.c +29 -81
@@ -2,7 +2,7 @@/* * CZ.NIC's Turris Omnia LEDs driver * -* 2020, 2023 by Marek Behún <[email protected]> +* 2020, 2023, 2024 by Marek Behún <[email protected]> */ #include <linux/i2c.h>
@@ -10,6 +10,7 @@#include <linux/module.h> #include <linux/mutex.h> #include <linux/of.h> +#include <linux/turris-omnia-mcu-interface.h> #include "leds.h" #define OMNIA_BOARD_LEDS 12
@@ -57,66 +58,21 @@ struct omnia_leds {struct omnia_led leds[]; }; -static int omnia_cmd_write_u8 (const struct i2c_client *client,u8 cmd,u8 val) +static int omnia_cmd_set_color (const struct i2c_client *client,u8 led,u8 r,u8 g,u8 b) { -u8 buf[2 ] = { cmd, val }; -int ret; - - ret =i2c_master_send (client, buf,sizeof (buf)); +u8 buf[5 ] = {CMD_LED_COLOR , led, r, g, b }; -return ret <0 ? ret :0 ; -} - -static int omnia_cmd_read_raw (struct i2c_adapter *adapter,u8 addr,u8 cmd, -void *reply,size_t len) -{ -struct i2c_msg msgs[2 ]; -int ret; - - msgs[0 ].addr = addr; - msgs[0 ].flags =0 ; - msgs[0 ].len =1 ; - msgs[0 ].buf = &cmd; - msgs[1 ].addr = addr; - msgs[1 ].flags =I2C_M_RD ; - msgs[1 ].len = len; - msgs[1 ].buf = reply; - - ret =i2c_transfer (adapter, msgs,ARRAY_SIZE (msgs)); -if (likely (ret ==ARRAY_SIZE (msgs))) -return 0 ; -else if (ret <0 ) -return ret; -else -return -EIO ; -} - -static int omnia_cmd_read_u8 (const struct i2c_client *client,u8 cmd) -{ -u8 reply; -int err; - - err =omnia_cmd_read_raw (client->adapter, client->addr, cmd, &reply,1 ); -if (err) -return err; - -return reply; +return omnia_cmd_write (client, buf,sizeof (buf)); }static int omnia_led_send_color_cmd (const struct i2c_client *client,struct omnia_led *led) { -char cmd[5 ];int ret; - cmd[0 ] =CMD_LED_COLOR ; - cmd[1 ] = led->reg; - cmd[2 ] = led->subled_info[0 ].brightness; - cmd[3 ] = led->subled_info[1 ].brightness; - cmd[4 ] = led->subled_info[2 ].brightness; -/* Send the color change command */ - ret =i2c_master_send (client, cmd,5 ); + ret =omnia_cmd_set_color (client, led->reg, led->subled_info[0 ].brightness, + led->subled_info[1 ].brightness, led->subled_info[2 ].brightness);if (ret <0 )return ret;
@@ -352,14 +308,14 @@ static ssize_t brightness_show(struct device *dev, struct device_attribute *a, char *buf) {struct i2c_client *client =to_i2c_client (dev); -int ret; - - ret =omnia_cmd_read_u8 (client,CMD_LED_GET_BRIGHTNESS ); +u8 reply; +int err; -if (ret <0 ) -return ret; + err =omnia_cmd_read_u8 (client,CMD_LED_GET_BRIGHTNESS , &reply); +if (err <0 ) +return err; -return sysfs_emit (buf,"%d\n" , ret); +return sysfs_emit (buf,"%d\n" , reply); } static ssize_t brightness_store(struct device *dev, struct device_attribute *a,
@@ -386,17 +342,16 @@ static ssize_t gamma_correction_show(struct device *dev, {struct i2c_client *client =to_i2c_client (dev);struct omnia_leds *leds =i2c_get_clientdata (client); -int ret; +u8 reply =0 ; +int err;if (leds->has_gamma_correction) { - ret =omnia_cmd_read_u8 (client,CMD_GET_GAMMA_CORRECTION ); -if (ret <0 ) -return ret; - }else { - ret =0 ; + err =omnia_cmd_read_u8 (client,CMD_GET_GAMMA_CORRECTION , &reply); +if (err <0 ) +return err; } -return sysfs_emit (buf,"%d\n" , !!ret); +return sysfs_emit (buf,"%d\n" , !!reply); } static ssize_t gamma_correction_store(struct device *dev,
@@ -429,24 +384,26 @@ ATTRIBUTE_GROUPS(omnia_led_controller);static int omnia_mcu_get_features (const struct i2c_client *client) { +struct i2c_client mcu_client = *client;u16 reply;int err; - err =omnia_cmd_read_raw (client->adapter,OMNIA_MCU_I2C_ADDR , -CMD_GET_STATUS_WORD , &reply,sizeof (reply)); +/* We have to read features from different I2C address */ + mcu_client.addr =OMNIA_MCU_I2C_ADDR ; + + err =omnia_cmd_read_u16 (&mcu_client,CMD_GET_STATUS_WORD , &reply);if (err)return err;/* Check whether MCU firmware supports the CMD_GET_FEAUTRES command */ -if (!(le16_to_cpu (reply) &STS_FEATURES_SUPPORTED )) +if (!(reply &STS_FEATURES_SUPPORTED ))return 0 ; - err =omnia_cmd_read_raw (client->adapter,OMNIA_MCU_I2C_ADDR , -CMD_GET_FEATURES , &reply,sizeof (reply)); + err =omnia_cmd_read_u16 (&mcu_client,CMD_GET_FEATURES , &reply);if (err)return err; -return le16_to_cpu (reply); +return reply; }static int omnia_leds_probe (struct i2c_client *client)
@@ -510,20 +467,11 @@ static int omnia_leds_probe(struct i2c_client *client)static void omnia_leds_remove (struct i2c_client *client) { -u8 buf[5 ]; -/* put all LEDs into default (HW triggered) mode */ -omnia_cmd_write_u8 (client,CMD_LED_MODE , -CMD_LED_MODE_LED (OMNIA_BOARD_LEDS )); +omnia_cmd_write_u8 (client,CMD_LED_MODE ,CMD_LED_MODE_LED (OMNIA_BOARD_LEDS ));/* set all LEDs color to [255, 255, 255] */ - buf[0 ] =CMD_LED_COLOR ; - buf[1 ] =OMNIA_BOARD_LEDS ; - buf[2 ] =255 ; - buf[3 ] =255 ; - buf[4 ] =255 ; - -i2c_master_send (client, buf,5 ); +omnia_cmd_set_color (client,OMNIA_BOARD_LEDS ,255 ,255 ,255 ); }static const struct of_device_id of_omnia_leds_match[] = {
Signature · 1 line
2.44.2
kernel test robot
build botRe: [PATCH leds v3 02/11] leds: turris-omnia: Use command execution functions from the MCU driver
kernel test robot noticed the following build errors:
Hi Marek,
kernel test robot noticed the following build errors:
[auto build test ERROR on next-20240913]
[also build test ERROR on v6.11-rc7]
[cannot apply to lee-leds/for-leds-next robh/for-next linus/master v6.11-rc7 v6.11-rc6 v6.11-rc5] [If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]
url: https://github.com/intel-lab-lkp/linux/commits/Marek-Beh-n/turris-omnia-mcu-interface-h-Move-command-execution-function-to-global-header/20240913-203320 base: next-20240913 patch link: https://lore.kernel.org/r/20240913123103.21226-3-kabel%40kernel.org patch subject: [PATCH leds v3 02/11] leds: turris-omnia: Use command execution functions from the MCU driver config: arc-randconfig-001-20240914 (https://download.01.org/0day-ci/archive/20240914/[email protected]/config) compiler: arc-elf-gcc (GCC) 13.2.0 reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20240914/[email protected]/reproduce)
If you fix the issue in a separate patch/commit (i.e. not just a new version of the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <[email protected]>
| Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
All errors (new ones prefixed by >>):
arc-elf-ld: drivers/leds/leds-turris-omnia.o: in function `gamma_correction_show':
>> leds-turris-omnia.c:(.text+0x26): undefined reference to `omnia_cmd_write_read' >> arc-elf-ld: leds-turris-omnia.c:(.text+0x26): undefined reference to `omnia_cmd_write_read'
arc-elf-ld: drivers/leds/leds-turris-omnia.o: in function `brightness_show':
leds-turris-omnia.c:(.text+0x98): undefined reference to `omnia_cmd_write_read'
arc-elf-ld: leds-turris-omnia.c:(.text+0x98): undefined reference to `omnia_cmd_write_read'
arc-elf-ld: drivers/leds/leds-turris-omnia.o: in function `omnia_led_send_color_cmd':
leds-turris-omnia.c:(.text+0xfc): undefined reference to `omnia_cmd_write_read'
arc-elf-ld: drivers/leds/leds-turris-omnia.o:leds-turris-omnia.c:(.text+0xfc): more undefined references to `omnia_cmd_write_read' follow
Signature · 2 lines
0-DAY CI Kernel Test Service https://github.com/intel/lkp-tests/wiki
kernel test robot
build botRe: [PATCH leds v3 02/11] leds: turris-omnia: Use command execution functions from the MCU driver
In reply to Marek Behúnkernel test robot noticed the following build errors:
Hi Marek,
kernel test robot noticed the following build errors:
[auto build test ERROR on next-20240913]
[also build test ERROR on v6.11-rc7]
[cannot apply to lee-leds/for-leds-next robh/for-next linus/master v6.11-rc7 v6.11-rc6 v6.11-rc5] [If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]
url: https://github.com/intel-lab-lkp/linux/commits/Marek-Beh-n/turris-omnia-mcu-interface-h-Move-command-execution-function-to-global-header/20240913-203320 base: next-20240913 patch link: https://lore.kernel.org/r/20240913123103.21226-3-kabel%40kernel.org patch subject: [PATCH leds v3 02/11] leds: turris-omnia: Use command execution functions from the MCU driver config: i386-buildonly-randconfig-002-20240914 (https://download.01.org/0day-ci/archive/20240914/[email protected]/config) compiler: clang version 18.1.8 (https://github.com/llvm/llvm-project 3b5b5c1ec4a3095ab096dd780e84d7ab81f3d7ff) reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20240914/[email protected]/reproduce)
If you fix the issue in a separate patch/commit (i.e. not just a new version of the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <[email protected]>
| Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
All errors (new ones prefixed by >>, old ones prefixed by <<):
>> ERROR: modpost: "omnia_cmd_write_read" [drivers/leds/leds-turris-omnia.ko] undefined!
Signature · 2 lines
0-DAY CI Kernel Test Service https://github.com/intel/lkp-tests/wiki
Marek Behún
maintainerPATCH v3 3/11 turris-omnia-mcu-interface.h: Add LED commands related definitions to global header
In reply to Marek BehúnAdd definitions for contents of the OMNIA_CMD_LED_MODE and OMNIA_CMD_LED_STATE commands to the global turris-omnia-mcu-interface.h header.
--- include/linux/turris-omnia-mcu-interface.h | 12 ++++++++++++ 1 file changed, 12 insertions(+)
include/linux/turris-omnia-mcu-interface.h +12 -0
@@ -239,6 +239,18 @@ enum omnia_int_e { OMNIA_INT_LAN5_LED1 = BIT(31), }; +enum omnia_cmd_led_mode_e { +OMNIA_CMD_LED_MODE_LED_MASK =GENMASK (3 ,0 ), +#define OMNIA_CMD_LED_MODE_LED(_l) FIELD_PREP(OMNIA_CMD_LED_MODE_LED_MASK, _l) + OMNIA_CMD_LED_MODE_USER = BIT(4), +}; + +enum omnia_cmd_led_state_e { +OMNIA_CMD_LED_STATE_LED_MASK =GENMASK (3 ,0 ), +#define OMNIA_CMD_LED_STATE_LED(_l) FIELD_PREP(OMNIA_CMD_LED_STATE_LED_MASK, _l) + OMNIA_CMD_LED_STATE_ON = BIT(4), +}; +enum omnia_cmd_poweroff_e {OMNIA_CMD_POWER_OFF_POWERON_BUTTON =BIT (0 ),OMNIA_CMD_POWER_OFF_MAGIC =0xdead ,
Signature · 1 line
2.44.2
Marek Behún
maintainerPATCH v3 4/11 leds: turris-omnia: Use global header for MCU command definitions
In reply to Marek BehúnThe global turris-omnia-mcu-interface.h header file contains the definitions for MCU commands. Drop the driver-internal definitions and use the global ones.
--- drivers/leds/leds-turris-omnia.c | 71 +++++++++++--------------------- 1 file changed, 23 insertions(+), 48 deletions(-)
drivers/leds/leds-turris-omnia.c +23 -48
@@ -16,30 +16,8 @@#define OMNIA_BOARD_LEDS 12#define OMNIA_LED_NUM_CHANNELS 3 -/* MCU controller commands at I2C address 0x2a */ -#define OMNIA_MCU_I2C_ADDR 0x2a - -#define CMD_GET_STATUS_WORD 0x01 -#define STS_FEATURES_SUPPORTED BIT(2) - -#define CMD_GET_FEATURES 0x10 -#define FEAT_LED_GAMMA_CORRECTION BIT(5) - -/* LED controller commands at I2C address 0x2b */ -#define CMD_LED_MODE 0x03 -#define CMD_LED_MODE_LED (l) ((l) & 0x0f) -#define CMD_LED_MODE_USER 0x10 - -#define CMD_LED_STATE 0x04 -#define CMD_LED_STATE_LED (l) ((l) & 0x0f) -#define CMD_LED_STATE_ON 0x10 - -#define CMD_LED_COLOR 0x05 -#define CMD_LED_SET_BRIGHTNESS 0x07 -#define CMD_LED_GET_BRIGHTNESS 0x08 - -#define CMD_SET_GAMMA_CORRECTION 0x30 -#define CMD_GET_GAMMA_CORRECTION 0x31 +/* MCU controller I2C address 0x2a, needed for detecting MCU features */ +#define OMNIA_MCU_I2C_ADDR 0x2astruct omnia_led {struct led_classdev_mc mc_cdev;
@@ -60,7 +38,7 @@ struct omnia_leds {static int omnia_cmd_set_color (const struct i2c_client *client,u8 led,u8 r,u8 g,u8 b) { -u8 buf[5 ] = {CMD_LED_COLOR , led, r, g, b }; +u8 buf[5 ] = {OMNIA_CMD_LED_COLOR , led, r, g, b };return omnia_cmd_write (client, buf,sizeof (buf)); }
@@ -127,12 +105,12 @@ static int omnia_led_brightness_set_blocking(struct led_classdev *cdev,* is not being blinked by HW. */ if (!err && !led->hwtrig && !brightness != !led->on) { -u8 state =CMD_LED_STATE_LED (led->reg); +u8 state =OMNIA_CMD_LED_STATE_LED (led->reg);if (brightness) - state |=CMD_LED_STATE_ON ; + state |=OMNIA_CMD_LED_STATE_ON ; - err =omnia_cmd_write_u8 (leds->client,CMD_LED_STATE , state); + err =omnia_cmd_write_u8 (leds->client,OMNIA_CMD_LED_STATE , state);if (!err) led->on = !!brightness; }
@@ -167,8 +145,8 @@ static int omnia_hwtrig_activate(struct led_classdev *cdev)if (!err) {/* Put the LED into MCU controlled mode */ - err =omnia_cmd_write_u8 (leds->client,CMD_LED_MODE , -CMD_LED_MODE_LED (led->reg)); + err =omnia_cmd_write_u8 (leds->client,OMNIA_CMD_LED_MODE , +OMNIA_CMD_LED_MODE_LED (led->reg));if (!err) led->hwtrig = true; }
@@ -189,9 +167,8 @@ static void omnia_hwtrig_deactivate(struct led_classdev *cdev) led->hwtrig = false;/* Put the LED into software mode */ - err =omnia_cmd_write_u8 (leds->client,CMD_LED_MODE , -CMD_LED_MODE_LED (led->reg) | -CMD_LED_MODE_USER ); + err =omnia_cmd_write_u8 (leds->client,OMNIA_CMD_LED_MODE , +OMNIA_CMD_LED_MODE_LED (led->reg) |OMNIA_CMD_LED_MODE_USER );mutex_unlock (&leds->lock);
@@ -258,9 +235,8 @@ static int omnia_led_register(struct i2c_client *client, struct omnia_led *led, cdev->default_trigger = omnia_hw_trigger.name;/* put the LED into software mode */ - ret =omnia_cmd_write_u8 (client,CMD_LED_MODE , -CMD_LED_MODE_LED (led->reg) | -CMD_LED_MODE_USER ); + ret =omnia_cmd_write_u8 (client,OMNIA_CMD_LED_MODE ,OMNIA_CMD_LED_MODE_LED (led->reg) | +OMNIA_CMD_LED_MODE_USER );if (ret) {dev_err (dev,"Cannot set LED %pOF to software mode: %i\n" , np, ret);
@@ -268,8 +244,7 @@ static int omnia_led_register(struct i2c_client *client, struct omnia_led *led, }/* disable the LED */ - ret =omnia_cmd_write_u8 (client,CMD_LED_STATE , -CMD_LED_STATE_LED (led->reg)); + ret =omnia_cmd_write_u8 (client,OMNIA_CMD_LED_STATE ,OMNIA_CMD_LED_STATE_LED (led->reg));if (ret) {dev_err (dev,"Cannot set LED %pOF brightness: %i\n" , np, ret);return ret;
@@ -311,7 +286,7 @@ static ssize_t brightness_show(struct device *dev, struct device_attribute *a,u8 reply;int err; - err =omnia_cmd_read_u8 (client,CMD_LED_GET_BRIGHTNESS , &reply); + err =omnia_cmd_read_u8 (client,OMNIA_CMD_GET_BRIGHTNESS , &reply);if (err <0 )return err;
@@ -331,7 +306,7 @@ static ssize_t brightness_store(struct device *dev, struct device_attribute *a,if (brightness >100 )return -EINVAL ; - err =omnia_cmd_write_u8 (client,CMD_LED_SET_BRIGHTNESS , brightness); + err =omnia_cmd_write_u8 (client,OMNIA_CMD_SET_BRIGHTNESS , brightness);return err ?: count; }
@@ -346,7 +321,7 @@ static ssize_t gamma_correction_show(struct device *dev,int err;if (leds->has_gamma_correction) { - err =omnia_cmd_read_u8 (client,CMD_GET_GAMMA_CORRECTION , &reply); + err =omnia_cmd_read_u8 (client,OMNIA_CMD_GET_GAMMA_CORRECTION , &reply);if (err <0 )return err; }
@@ -369,7 +344,7 @@ static ssize_t gamma_correction_store(struct device *dev,if (kstrtobool (buf, &val) <0 )return -EINVAL ; - err =omnia_cmd_write_u8 (client,CMD_SET_GAMMA_CORRECTION , val); + err =omnia_cmd_write_u8 (client,OMNIA_CMD_SET_GAMMA_CORRECTION , val);return err ?: count; }
@@ -391,15 +366,15 @@ static int omnia_mcu_get_features(const struct i2c_client *client)/* We have to read features from different I2C address */ mcu_client.addr =OMNIA_MCU_I2C_ADDR ; - err =omnia_cmd_read_u16 (&mcu_client,CMD_GET_STATUS_WORD , &reply); + err =omnia_cmd_read_u16 (&mcu_client,OMNIA_CMD_GET_STATUS_WORD , &reply);if (err)return err; -/* Check whether MCU firmware supports the CMD_GET_FEAUTRES command */ -if (!(reply &STS_FEATURES_SUPPORTED )) +/* Check whether MCU firmware supports the OMNIA_CMD_GET_FEAUTRES command */ +if (!(reply &OMNIA_STS_FEATURES_SUPPORTED ))return 0 ; - err =omnia_cmd_read_u16 (&mcu_client,CMD_GET_FEATURES , &reply); + err =omnia_cmd_read_u16 (&mcu_client,OMNIA_CMD_GET_FEATURES , &reply);if (err)return err;
@@ -437,7 +412,7 @@ static int omnia_leds_probe(struct i2c_client *client)return ret; } - leds->has_gamma_correction = ret &FEAT_LED_GAMMA_CORRECTION ; + leds->has_gamma_correction = ret &OMNIA_FEAT_LED_GAMMA_CORRECTION ;if (!leds->has_gamma_correction) {dev_info (dev,"Your board's MCU firmware does not support the LED gamma correction feature.\n" );
@@ -468,7 +443,7 @@ static int omnia_leds_probe(struct i2c_client *client)static void omnia_leds_remove (struct i2c_client *client) {/* put all LEDs into default (HW triggered) mode */ -omnia_cmd_write_u8 (client,CMD_LED_MODE ,CMD_LED_MODE_LED (OMNIA_BOARD_LEDS )); +omnia_cmd_write_u8 (client,OMNIA_CMD_LED_MODE ,OMNIA_CMD_LED_MODE_LED (OMNIA_BOARD_LEDS ));/* set all LEDs color to [255, 255, 255] */ omnia_cmd_set_color (client,OMNIA_BOARD_LEDS ,255 ,255 ,255 );
Signature · 1 line
2.44.2
Marek Behún
maintainerPATCH v3 5/11 dt-bindings: leds: cznic,turris-omnia-leds: Allow interrupts property
In reply to Marek BehúnExtend the cznic,turris-omnia-leds binding with interrupts property, specifying the global LED brightness changed by button press interrupt.
--- .../devicetree/bindings/leds/cznic,turris-omnia-leds.yaml | 8 ++++++++ 1 file changed, 8 insertions(+)
Documentation/devicetree/bindings/leds/cznic,turris-omnia-leds.yaml +8 -0
@@ -23,6 +23,12 @@ properties: description: I2C slave address of the microcontroller. maxItems: 1 + interrupts: + description: + Specifier for the global LED brightness changed by front button press + interrupt. + maxItems: 1 + "#address-cells": const: 1
@@ -56,6 +62,7 @@ additionalProperties: false examples: - | + #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/leds/common.h> i2c {
@@ -65,6 +72,7 @@ examples: led-controller@2b { compatible = "cznic,turris-omnia-leds"; reg = <0x2b>; + interrupts-extended = <&mcu 11 IRQ_TYPE_NONE>; #address-cells = <1>; #size-cells = <0>;
Signature · 1 line
2.44.2
Re: [PATCH leds v3 05/11] dt-bindings: leds: cznic,turris-omnia-leds: Allow interrupts property
Quoted 13 lines · Marek Behún
Extend the cznic,turris-omnia-leds binding with interrupts property, specifying the global LED brightness changed by button press interrupt.
Signed-off-by Marek Behún <[email protected]>--- .../devicetree/bindings/leds/cznic,turris-omnia-leds.yaml | 8 ++++++++ 1 file changed, 8 insertions(+)Documentation/devicetree/bindings/leds/cznic,turris-omnia-leds.yaml +0
-0
Documentation/devicetree/bindings/leds/cznic,turris-omnia-leds.yaml properties: · line 29
Quoted 7 lines
Documentation/devicetree/bindings/leds/cznic,turris-omnia-leds.yaml +4
-0@@ -23,6 +23,12 @@ properties: description: I2C slave address of the microcontroller. maxItems: 1 + interrupts: + description: + Specifier for the global LED brightness changed by front button press + interrupt.
This "front button press" concerns me that you just hooked here gpio-key. Are you sure that this is the physical interrupt line going to this device?
Best regards,
Krzysztof
Marek Behún
maintainerRe: [PATCH leds v3 05/11] dt-bindings: leds: cznic,turris-omnia-leds: Allow interrupts property
Quoted 17 lines · Krzysztof Kozlowski
Quoted 16 lines · Marek Behún
Extend the cznic,turris-omnia-leds binding with interrupts property, specifying the global LED brightness changed by button press interrupt.
Signed-off-by Marek Behún <[email protected]>--- .../devicetree/bindings/leds/cznic,turris-omnia-leds.yaml | 8 ++++++++ 1 file changed, 8 insertions(+)Documentation/devicetree/bindings/leds/cznic,turris-omnia-leds.yaml +0
-0@@ -23,6 +23,12 @@ properties: description: I2C slave address of the microcontroller. maxItems: 1
Quoted 8 lines
Documentation/devicetree/bindings/leds/cznic,turris-omnia-leds.yaml properties: · line 29
Quoted 4 lines
Documentation/devicetree/bindings/leds/cznic,turris-omnia-leds.yaml +4
-0+ interrupts: + description: + Specifier for the global LED brightness changed by front button press + interrupt.This "front button press" concerns me that you just hooked here gpio-key. Are you sure that this is the physical interrupt line going to this device?
No no no, that is a different interrupt from the gpio-key.
The button can be configure in two modes:
- it can act like a GPIO to the CPU, forwarding press and release events via the GPIO chip (so button press it is handled by CPU)
- can be set with
echo cpu >/sys/bus/i2c/devices/1-002a/front_button_mode
- pressing it will generate the INT_BUTTON_PRESSED interrupt from the MCU
- it can change LED panel brightness (so button press is handled by MCU)
- this is the default mode, configured after boot
- can be set with
echo mcu >/sys/bus/i2c/devices/1-002a/front_button_mode
- pressing it will generate the INT_BRIGHTNESS_CHANGED interrupt
The INT_BUTTON_PRESSED and INT_BRIGHTNESS_CHANGED interrupt semantically different (and also literally, they are at different bits). See
https://gitlab.nic.cz/turris/hw/omnia_hw_ctrl/-/blob/master/src/drivers/i2c_iface.h?ref_type=heads#L289-L321
Marek
Re: [PATCH leds v3 05/11] dt-bindings: leds: cznic,turris-omnia-leds: Allow interrupts property
Quoted 41 lines · Marek Behún
Quoted 17 lines · Krzysztof Kozlowski
Quoted 16 lines · Marek Behún
Extend the cznic,turris-omnia-leds binding with interrupts property, specifying the global LED brightness changed by button press interrupt.
Signed-off-by Marek Behún <[email protected]>--- .../devicetree/bindings/leds/cznic,turris-omnia-leds.yaml | 8 ++++++++ 1 file changed, 8 insertions(+)Documentation/devicetree/bindings/leds/cznic,turris-omnia-leds.yaml +0
-0@@ -23,6 +23,12 @@ properties: description: I2C slave address of the microcontroller. maxItems: 1Quoted 8 lines
Documentation/devicetree/bindings/leds/cznic,turris-omnia-leds.yaml properties: · line 29
Quoted 4 lines
Documentation/devicetree/bindings/leds/cznic,turris-omnia-leds.yaml +4
-0+ interrupts: + description: + Specifier for the global LED brightness changed by front button press + interrupt.This "front button press" concerns me that you just hooked here gpio-key. Are you sure that this is the physical interrupt line going to this device?
No no no, that is a different interrupt from the gpio-key.
The button can be configure in two modes:
- it can act like a GPIO to the CPU, forwarding press and release events via the GPIO chip (so button press it is handled by CPU)
- can be set withecho cpu >/sys/bus/i2c/devices/1-002a/front_button_mode- pressing it will generate the
INT_BUTTON_PRESSEDinterrupt from the MCU- it can change LED panel brightness (so button press is handled by MCU)
- this is the default mode, configured after boot
- can be set with
Quoted 6 lines
echo mcu >/sys/bus/i2c/devices/1-002a/front_button_mode- pressing it will generate the
INT_BRIGHTNESS_CHANGEDinterruptThe
INT_BUTTON_PRESSEDandINT_BRIGHTNESS_CHANGEDinterrupt semantically different (and also literally, they are at different bits). See
https://gitlab.nic.cz/turris/hw/omnia_hw_ctrl/-/blob/master/src/drivers/i2c_iface.h?ref_type=heads#L289-L321
That's fine, thanks for the explanation.
Best regards,
Krzysztof
Re: [PATCH leds v3 05/11] dt-bindings: leds: cznic,turris-omnia-leds: Allow interrupts property
In reply to Marek BehúnQuoted 5 lines · Marek Behún
Extend the cznic,turris-omnia-leds binding with interrupts property, specifying the global LED brightness changed by button press interrupt.
Signed-off-by Marek Behún <[email protected]>---
Best regards,
Krzysztof
Marek Behún
maintainerPATCH v3 6/11 leds: turris-omnia: Notify sysfs on MCU global LEDs brightness change
In reply to Marek BehúnRecall that on Turris Omnia, the LED controller has a global brightness property, which allows the user to make the front LED panel dimmer.
There is also a button on the front panel, which by default is configured so that pressing it changes the global brightness to a lower value (unless it is at 0%, in which case pressing the button changes the global brightness to 100%).
Newer versions of the MCU firmware support informing the SOC that the brightness was changed by button press event via an interrupt.
Now that we have the turris-omnia-mcu driver, which adds support for MCU interrupts, add the ability to inform the userspace (via a sysfs notification) that the global brightness was changed.
--- drivers/leds/leds-turris-omnia.c | 37 ++++++++++++++++++++++++++++++++ 1 file changed, 37 insertions(+)
drivers/leds/leds-turris-omnia.c +37 -0
@@ -33,6 +33,7 @@ struct omnia_leds {struct i2c_client *client;struct mutex lock;bool has_gamma_correction; +struct kernfs_node *brightness_kn;struct omnia_led leds[]; };
@@ -357,6 +358,21 @@ static struct attribute *omnia_led_controller_attrs[] = { };ATTRIBUTE_GROUPS (omnia_led_controller); +static irqreturn_t omnia_brightness_changed_handler (int irq,void *dev_id) +{ +struct omnia_leds *leds = dev_id; + +if (unlikely (!leds->brightness_kn)) { + leds->brightness_kn =sysfs_get_dirent (leds->client->dev.kobj.sd,"brightness" ); +if (!leds->brightness_kn) +return IRQ_NONE ; + } + +sysfs_notify_dirent (leds->brightness_kn); + +return IRQ_HANDLED ; +} +static int omnia_mcu_get_features (const struct i2c_client *client) {struct i2c_client mcu_client = *client;
@@ -420,6 +436,14 @@ static int omnia_leds_probe(struct i2c_client *client) "Consider upgrading MCU firmware with the omnia-mcutool utility.\n"); } +if (ret &OMNIA_FEAT_BRIGHTNESS_INT ) { + ret =devm_request_any_context_irq (dev, client->irq, + omnia_brightness_changed_handler,IRQF_ONESHOT , +"leds-turris-omnia" , leds); +if (ret <=0 ) +return dev_err_probe (dev, ret ?: -ENXIO ,"Cannot request brightness IRQ\n" ); + } +mutex_init (&leds->lock); ret =devm_led_trigger_register (dev, &omnia_hw_trigger);
@@ -442,6 +466,19 @@ static int omnia_leds_probe(struct i2c_client *client)static void omnia_leds_remove (struct i2c_client *client) { +struct omnia_leds *leds =i2c_get_clientdata (client); + +/* +* We need to free the brightness IRQ here, before putting away the brightness sysfs node. +* Otherwise devres would free the interrupt only after the sysfs node is removed, and if +* an interrupt occurred between those two events, it would use a removed sysfs node. +*/ +devm_free_irq (&client->dev, client->irq, leds); + +/* Now put away the sysfs node we got the first time the interrupt handler was called */ +if (leds->brightness_kn) +sysfs_put (leds->brightness_kn); +/* put all LEDs into default (HW triggered) mode */ omnia_cmd_write_u8 (client,OMNIA_CMD_LED_MODE ,OMNIA_CMD_LED_MODE_LED (OMNIA_BOARD_LEDS ));
Signature · 1 line
2.44.2
Lee Jones
maintainerRe: [PATCH leds v3 06/11] leds: turris-omnia: Notify sysfs on MCU global LEDs brightness change
Quoted 25 lines · Marek Behún
Recall that on Turris Omnia, the LED controller has a global brightness property, which allows the user to make the front LED panel dimmer.
There is also a button on the front panel, which by default is configured so that pressing it changes the global brightness to a lower value (unless it is at 0%, in which case pressing the button changes the global brightness to 100%).
Newer versions of the MCU firmware support informing the SOC that the brightness was changed by button press event via an interrupt.
Now that we have the turris-omnia-mcu driver, which adds support for MCU interrupts, add the ability to inform the userspace (via a sysfs notification) that the global brightness was changed.
Signed-off-by Marek Behún <[email protected]>--- drivers/leds/leds-turris-omnia.c | 37 ++++++++++++++++++++++++++++++++ 1 file changed, 37 insertions(+)drivers/leds/leds-turris-omnia.c +0
-0
drivers/leds/leds-turris-omnia.c struct omnia_leds { · line 36
Quoted 4 lines
drivers/leds/leds-turris-omnia.c +1
-0@@ -33,6 +33,7 @@ struct omnia_leds {struct i2c_client *client;struct mutex lock;bool has_gamma_correction; +struct kernfs_node *brightness_kn;
Variable nomenclature should be self documenting.
What is kn? Please improve this.
drivers/leds/leds-turris-omnia.c static struct attribute *omnia_led_controller_attrs[] = { · line 361
Quoted 8 lines
drivers/leds/leds-turris-omnia.c +1
-0struct omnia_led leds[]; };@@ -357,6 +358,21 @@ static struct attribute *omnia_led_controller_attrs[] = { };ATTRIBUTE_GROUPS (omnia_led_controller); +static irqreturn_t omnia_brightness_changed_handler (int irq,void *dev_id)
Why dev_id? This appears to be driver data. ddata sounds more applicable.
drivers/leds/leds-turris-omnia.c static struct attribute *omnia_led_controller_attrs[] = { · line 366
Quoted 5 lines
drivers/leds/leds-turris-omnia.c +5
-0+{ +struct omnia_leds *leds = dev_id; + +if (unlikely (!leds->brightness_kn)) { + leds->brightness_kn =sysfs_get_dirent (leds->client->dev.kobj.sd,"brightness" );
NACK. This will sleep in IRQ context.
Quoted 50 lines
drivers/leds/leds-turris-omnia.c +30
-0+if (!leds->brightness_kn) +return IRQ_NONE ; + } + +sysfs_notify_dirent (leds->brightness_kn); + +return IRQ_HANDLED ; +} +static int omnia_mcu_get_features (const struct i2c_client *client) {struct i2c_client mcu_client = *client;@@ -420,6 +436,14 @@ static int omnia_leds_probe(struct i2c_client *client) "Consider upgrading MCU firmware with the omnia-mcutool utility.\n"); } +if (ret &OMNIA_FEAT_BRIGHTNESS_INT ) { + ret =devm_request_any_context_irq (dev, client->irq, + omnia_brightness_changed_handler,IRQF_ONESHOT , +"leds-turris-omnia" , leds); +if (ret <=0 ) +return dev_err_probe (dev, ret ?: -ENXIO ,"Cannot request brightness IRQ\n" ); + } +mutex_init (&leds->lock); ret =devm_led_trigger_register (dev, &omnia_hw_trigger);@@ -442,6 +466,19 @@ static int omnia_leds_probe(struct i2c_client *client)static void omnia_leds_remove (struct i2c_client *client) { +struct omnia_leds *leds =i2c_get_clientdata (client); + +/* +* We need to free the brightness IRQ here, before putting away the brightness sysfs node. +* Otherwise devres would free the interrupt only after the sysfs node is removed, and if +* an interrupt occurred between those two events, it would use a removed sysfs node. +*/ +devm_free_irq (&client->dev, client->irq, leds); + +/* Now put away the sysfs node we got the first time the interrupt handler was called */ +if (leds->brightness_kn) +sysfs_put (leds->brightness_kn); +/* put all LEDs into default (HW triggered) mode */ omnia_cmd_write_u8 (client,OMNIA_CMD_LED_MODE ,OMNIA_CMD_LED_MODE_LED (OMNIA_BOARD_LEDS ));Signature · 1 line
2.44.2
Signature · 1 line
Lee Jones [李琼斯]
Marek Behún
maintainerPATCH v3 7/11 platform: cznic: turris-omnia-mcu: Inform about missing LED panel brightness change interrupt feature
In reply to Marek BehúnWhen reading MCU firmware features, check also for the LED panel brightness change interrupt feature, and suggest upgrading the firmware if it is missing.
--- drivers/platform/cznic/turris-omnia-mcu-base.c | 1 + 1 file changed, 1 insertion(+)
drivers/platform/cznic/turris-omnia-mcu-base.c +1 -0
@@ -258,6 +258,7 @@ static int omnia_mcu_read_features(struct omnia_mcu *mcu)_DEF_FEAT (NEW_INT_API ,"new interrupt API" ),_DEF_FEAT (POWEROFF_WAKEUP ,"poweroff and wakeup" ),_DEF_FEAT (TRNG ,"true random number generator" ), +_DEF_FEAT (BRIGHTNESS_INT ,"LED panel brightness change interrupt" ), #undef _DEF_FEAT };struct i2c_client *client = mcu->client;
Signature · 1 line
2.44.2
Marek Behún
maintainerPATCH v3 8/11 leds: turris-omnia: Inform about missing LED gamma correction feature in the MCU driver
In reply to Marek BehúnIf the LED gamma correction feature is missing in the MCU firmware, inform about this in the MCU firmware probe function instead of LED driver probe function, so that all the feature checks are in one place.
--- drivers/leds/leds-turris-omnia.c | 6 ------ drivers/platform/cznic/turris-omnia-mcu-base.c | 1 + 2 files changed, 1 insertion(+), 6 deletions(-)
drivers/leds/leds-turris-omnia.c +0 -6
@@ -429,12 +429,6 @@ static int omnia_leds_probe(struct i2c_client *client) } leds->has_gamma_correction = ret &OMNIA_FEAT_LED_GAMMA_CORRECTION ; -if (!leds->has_gamma_correction) { -dev_info (dev, -"Your board's MCU firmware does not support the LED gamma correction feature.\n" ); -dev_info (dev, -"Consider upgrading MCU firmware with the omnia-mcutool utility.\n" ); - }if (ret &OMNIA_FEAT_BRIGHTNESS_INT ) { ret = devm_request_any_context_irq(dev, client->irq,
drivers/platform/cznic/turris-omnia-mcu-base.c +1 -0
@@ -259,6 +259,7 @@ static int omnia_mcu_read_features(struct omnia_mcu *mcu)_DEF_FEAT (POWEROFF_WAKEUP ,"poweroff and wakeup" ),_DEF_FEAT (TRNG ,"true random number generator" ),_DEF_FEAT (BRIGHTNESS_INT ,"LED panel brightness change interrupt" ), +_DEF_FEAT (LED_GAMMA_CORRECTION ,"LED gamma correction" ), #undef _DEF_FEAT };struct i2c_client *client = mcu->client;
Signature · 1 line
2.44.2
Marek Behún
maintainerPATCH v3 9/11 leds: turris-omnia: Use dev_err_probe() where appropriate
In reply to Marek BehúnUse dev_err_probe() instead of dev_err() + separate return where appropriate.
--- drivers/leds/leds-turris-omnia.c | 50 ++++++++++---------------------- 1 file changed, 16 insertions(+), 34 deletions(-)
drivers/leds/leds-turris-omnia.c +16 -34
@@ -238,33 +238,23 @@ static int omnia_led_register(struct i2c_client *client, struct omnia_led *led,/* put the LED into software mode */ ret =omnia_cmd_write_u8 (client,OMNIA_CMD_LED_MODE ,OMNIA_CMD_LED_MODE_LED (led->reg) |OMNIA_CMD_LED_MODE_USER ); -if (ret) { -dev_err (dev,"Cannot set LED %pOF to software mode: %i\n" , np, - ret); -return ret; - } +if (ret) +return dev_err_probe (dev, ret,"Cannot set LED %pOF to software mode\n" , np);/* disable the LED */ ret =omnia_cmd_write_u8 (client,OMNIA_CMD_LED_STATE ,OMNIA_CMD_LED_STATE_LED (led->reg)); -if (ret) { -dev_err (dev,"Cannot set LED %pOF brightness: %i\n" , np, ret); -return ret; - } +if (ret) +return dev_err_probe (dev, ret,"Cannot set LED %pOF brightness\n" , np);/* Set initial color and cache it */ ret =omnia_led_send_color_cmd (client, led); -if (ret <0 ) { -dev_err (dev,"Cannot set LED %pOF initial color: %i\n" , np, - ret); -return ret; - } +if (ret <0 ) +return dev_err_probe (dev, ret,"Cannot set LED %pOF initial color\n" , np); ret =devm_led_classdev_multicolor_register_ext (dev, &led->mc_cdev, &init_data); -if (ret <0 ) { -dev_err (dev,"Cannot register LED %pOF: %i\n" , np, ret); -return ret; - } +if (ret <0 ) +return dev_err_probe (dev, ret,"Cannot register LED %pOF\n" , np);return 1 ; }
@@ -406,13 +396,10 @@ static int omnia_leds_probe(struct i2c_client *client)int ret, count; count =of_get_available_child_count (np); -if (!count) { -dev_err (dev,"LEDs are not defined in device tree!\n" ); -return -ENODEV ; - }else if (count >OMNIA_BOARD_LEDS ) { -dev_err (dev,"Too many LEDs defined in device tree!\n" ); -return -EINVAL ; - } +if (count ==0 ) +return dev_err_probe (dev, -ENODEV ,"LEDs are not defined in device tree!\n" ); +if (count >OMNIA_BOARD_LEDS ) +return dev_err_probe (dev, -EINVAL ,"Too many LEDs defined in device tree!\n" ); leds =devm_kzalloc (dev,struct_size (leds, leds, count),GFP_KERNEL );if (!leds)
@@ -422,11 +409,8 @@ static int omnia_leds_probe(struct i2c_client *client)i2c_set_clientdata (client, leds); ret =omnia_mcu_get_features (client); -if (ret <0 ) { -dev_err (dev,"Cannot determine MCU supported features: %d\n" , - ret); -return ret; - } +if (ret <0 ) +return dev_err_probe (dev, ret,"Cannot determine MCU supported features\n" ); leds->has_gamma_correction = ret &OMNIA_FEAT_LED_GAMMA_CORRECTION ;
@@ -441,10 +425,8 @@ static int omnia_leds_probe(struct i2c_client *client)mutex_init (&leds->lock); ret =devm_led_trigger_register (dev, &omnia_hw_trigger); -if (ret <0 ) { -dev_err (dev,"Cannot register private LED trigger: %d\n" , ret); -return ret; - } +if (ret <0 ) +return dev_err_probe (dev, ret,"Cannot register private LED trigger\n" ); led = &leds->leds[0 ];for_each_available_child_of_node_scoped (np, child) {
Signature · 1 line
2.44.2
Marek Behún
maintainerPATCH v3 10/11 leds: turris-omnia: Use uppercase first letter in all comments
In reply to Marek BehúnChange first letter of 4 more comments to uppercase to make the driver comments uniform.
--- drivers/leds/leds-turris-omnia.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/leds/leds-turris-omnia.c +4 -4
@@ -235,13 +235,13 @@ static int omnia_led_register(struct i2c_client *client, struct omnia_led *led,*/ cdev->default_trigger = omnia_hw_trigger.name; -/* put the LED into software mode */ +/* Put the LED into software mode */ ret =omnia_cmd_write_u8 (client,OMNIA_CMD_LED_MODE ,OMNIA_CMD_LED_MODE_LED (led->reg) |OMNIA_CMD_LED_MODE_USER );if (ret)return dev_err_probe (dev, ret,"Cannot set LED %pOF to software mode\n" , np); -/* disable the LED */ +/* Disable the LED */ ret =omnia_cmd_write_u8 (client,OMNIA_CMD_LED_STATE ,OMNIA_CMD_LED_STATE_LED (led->reg));if (ret)return dev_err_probe (dev, ret,"Cannot set LED %pOF brightness\n" , np);
@@ -455,10 +455,10 @@ static void omnia_leds_remove(struct i2c_client *client)if (leds->brightness_kn)sysfs_put (leds->brightness_kn); -/* put all LEDs into default (HW triggered) mode */ +/* Put all LEDs into default (HW triggered) mode */ omnia_cmd_write_u8 (client,OMNIA_CMD_LED_MODE ,OMNIA_CMD_LED_MODE_LED (OMNIA_BOARD_LEDS )); -/* set all LEDs color to [255, 255, 255] */ +/* Set all LEDs color to [255, 255, 255] */ omnia_cmd_set_color (client,OMNIA_BOARD_LEDS ,255 ,255 ,255 ); }
Signature · 1 line
2.44.2
Marek Behún
maintainerPATCH v3 11/11 ARM: dts: turris-omnia: Add global LED brightness change interrupt
In reply to Marek BehúnWhen global LED brightness is changed by pressing the front button on Turris Omnia, the MCU can produce an interrupt to the CPU. Add the description of this interrupt to the LED controller node.
--- arch/arm/boot/dts/marvell/armada-385-turris-omnia.dts | 1 + 1 file changed, 1 insertion(+)
arch/arm/boot/dts/marvell/armada-385-turris-omnia.dts +1 -0
@@ -251,6 +251,7 @@ mcu: system-controller@2a { led-controller@2b { compatible = "cznic,turris-omnia-leds"; reg = <0x2b>; + interrupts-extended = <&mcu 11 IRQ_TYPE_NONE>; #address-cells = <1>; #size-cells = <0>; status = "okay";
Signature · 1 line
2.44.2