Re-introduce TX FIFO resize for larger EP bursting

Some devices have USB compositions which may require multiple endpoints that support EP bursting. HW defined TX FIFO sizes may not always be sufficient for these compositions. By utilizing flexible TX FIFO allocation, this allows for endpoints to request the required FIFO depth to achieve higher bandwidth. With some higher bMaxBurst configurations, using a larger TX FIFO size results in better TX throughput.

By introducing the check_config() callback, the resizing logic can fetch the maximum number of endpoints used in the USB composition (can contain multiple configurations), which helps ensure that the resizing logic can fulfill the configuration(s), or return an error to the gadget layer otherwise during bind time.

Signed-off-by Wesley Cheng <[email protected]>

---
 drivers/usb/dwc3/core.c   |  15 +++
 drivers/usb/dwc3/core.h   |  16 ++++
 drivers/usb/dwc3/ep0.c    |   2 +
 drivers/usb/dwc3/gadget.c | 232 ++++++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 265 insertions(+)

drivers/usb/dwc3/core.c +8 -0

index ba74ad7..b194aecd 100644
@@ -1267,6 +1267,7 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 	u8			rx_max_burst_prd;
 	u8			tx_thr_num_pkt_prd;
 	u8			tx_max_burst_prd;
+	u8			tx_fifo_resize_max_num;
 	const char		*usb_psy_name;
 	int			ret;
 

@@ -1282,6 +1283,13 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 	 */
 	hird_threshold = 12;
 
+	/*
+	 * default to a TXFIFO size large enough to fit 6 max packets.  This
+	 * allows for systems with larger bus latencies to have some headroom
+	 * for endpoints that have a large bMaxBurst value.
+	 */
+	tx_fifo_resize_max_num = 6;
+
 	dwc->maximum_speed = usb_get_maximum_speed(dev);
 	dwc->max_ssp_rate = usb_get_maximum_ssp_rate(dev);
 	dwc->dr_mode = usb_get_dr_mode(dev);

drivers/usb/dwc3/core.c +0 -0

 }
 
 /* check whether the core supports IMOD */

drivers/usb/dwc3/core.h +16 -0

index dccdf13..735e9be 100644
@@ -1023,6 +1023,7 @@ struct dwc3_scratchpad_array {
  * @rx_max_burst_prd: max periodic ESS receive burst size
  * @tx_thr_num_pkt_prd: periodic ESS transmit packet count
  * @tx_max_burst_prd: max periodic ESS transmit burst size
+ * @tx_fifo_resize_max_num: max number of fifos allocated during txfifo resize
  * @hsphy_interface: "utmi" or "ulpi"
  * @connected: true when we're connected to a host, false otherwise
  * @delayed_status: true when gadget driver asks for delayed status

@@ -1037,6 +1038,7 @@ struct dwc3_scratchpad_array {
  *	1	- utmi_l1_suspend_n
  * @is_fpga: true when we are using the FPGA board
  * @pending_events: true when we have pending IRQs to be handled
+ * @do_fifo_resize: true when txfifo resizing is enabled for dwc3 endpoints
  * @pullups_connected: true when Run/Stop bit is set
  * @setup_packet_pending: true when there's a Setup Packet in FIFO. Workaround
  * @three_stage_setup: set if we perform a three phase setup

@@ -1079,6 +1081,11 @@ struct dwc3_scratchpad_array {
  * @dis_split_quirk: set to disable split boundary.
  * @imod_interval: set the interrupt moderation interval in 250ns
  *			increments or 0 to disable.
+ * @max_cfg_eps: current max number of IN eps used across all USB configs.
+ * @last_fifo_depth: last fifo depth used to determine next fifo ram start
+ *		     address.
+ * @num_ep_resized: carries the current number endpoints which have had its tx
+ *		    fifo resized.
  */
 struct dwc3 {
 	struct work_struct	drd_work;

@@ -1233,6 +1240,7 @@ struct dwc3 {
 	u8			rx_max_burst_prd;
 	u8			tx_thr_num_pkt_prd;
 	u8			tx_max_burst_prd;
+	u8			tx_fifo_resize_max_num;
 
 	const char		*hsphy_interface;
 

@@ -1246,6 +1254,7 @@ struct dwc3 {
 	unsigned		is_utmi_l1_suspend:1;
 	unsigned		is_fpga:1;
 	unsigned		pending_events:1;
+	unsigned		do_fifo_resize:1;
 	unsigned		pullups_connected:1;
 	unsigned		setup_packet_pending:1;
 	unsigned		three_stage_setup:1;

@@ -1281,6 +1290,10 @@ struct dwc3 {
 	unsigned		dis_split_quirk:1;
 
 	u16			imod_interval;
+
+	int			max_cfg_eps;
+	int			last_fifo_depth;
+	int			num_ep_resized;
 };
 
 #define INCRX_BURST_MODE 0

@@ -1512,6 +1525,7 @@ int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned int cmd,
 		struct dwc3_gadget_ep_cmd_params *params);
 int dwc3_send_gadget_generic_command(struct dwc3 *dwc, unsigned int cmd,
 		u32 param);
+void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc);
 #else
 static inline int dwc3_gadget_init(struct dwc3 *dwc)
 { return 0; }

@@ -1531,6 +1545,8 @@ static inline int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned int cmd,
 static inline int dwc3_send_gadget_generic_command(struct dwc3 *dwc,
 		int cmd, u32 param)
 { return 0; }
+static inline void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc)
+{ }
 #endif
 
 #if IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE)

drivers/usb/dwc3/ep0.c +2 -0

index 3cd2942..d28d085 100644
@@ -619,6 +619,8 @@ static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl)
 		return -EINVAL;
 
 	case USB_STATE_ADDRESS:
+		dwc3_gadget_clear_tx_fifos(dwc);
+
 		ret = dwc3_ep0_delegate_req(dwc, ctrl);
 		/* if the cfg matches and the cfg is non zero */
 		if (cfg && (!ret || (ret == USB_GADGET_DELAYED_STATUS))) {

drivers/usb/dwc3/gadget.c +115 -0

index af6d7f1..e56f1a6 100644
@@ -632,6 +632,187 @@ static void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force,
 		bool interrupt);
 
 /**
+ * dwc3_gadget_calc_tx_fifo_size - calculates the txfifo size value
+ * @dwc: pointer to the DWC3 context
+ * @nfifos: number of fifos to calculate for
+ *
+ * Calculates the size value based on the equation below:
+ *
+ * DWC3 revision 280A and prior:
+ * fifo_size = mult * (max_packet / mdwidth) + 1;
+ *
+ * DWC3 revision 290A and onwards:
+ * fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1
+ *
+ * The max packet size is set to 1024, as the txfifo requirements mainly apply
+ * to super speed USB use cases.  However, it is safe to overestimate the fifo
+ * allocations for other scenarios, i.e. high speed USB.
+ */
+static int dwc3_gadget_calc_tx_fifo_size(struct dwc3 *dwc, int mult)
+{
+	int max_packet = 1024;
+	int fifo_size;
+	int mdwidth;
+
+	mdwidth = dwc3_mdwidth(dwc);
+
+	/* MDWIDTH is represented in bits, we need it in bytes */
+	mdwidth >>= 3;
+
+	if (DWC3_VER_IS_PRIOR(DWC3, 290A))
+		fifo_size = mult * (max_packet / mdwidth) + 1;
+	else
+		fifo_size = mult * ((max_packet + mdwidth) / mdwidth) + 1;
+	return fifo_size;
+}
+
+/**
+ * dwc3_gadget_clear_tx_fifo_size - Clears txfifo allocation
+ * @dwc: pointer to the DWC3 context
+ *
+ * Iterates through all the endpoint registers and clears the previous txfifo
+ * allocations.
+ */
+void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc)
+{
+	struct dwc3_ep *dep;
+	int fifo_depth;
+	int size;
+	int num;
+
+	if (!dwc->do_fifo_resize)
+		return;
+
+	/* Read ep0IN related TXFIFO size */
+	dep = dwc->eps[1];
+	size = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0));
+	if (DWC3_IP_IS(DWC3))
+		fifo_depth = DWC3_GTXFIFOSIZ_TXFDEP(size);
+	else
+		fifo_depth = DWC31_GTXFIFOSIZ_TXFDEP(size);
+
+	dwc->last_fifo_depth = fifo_depth;
+	/* Clear existing TXFIFO for all IN eps except ep0 */
+	for (num = 3; num < min_t(int, dwc->num_eps, DWC3_ENDPOINTS_NUM);
+	     num += 2) {
+		dep = dwc->eps[num];
+		/* Don't change TXFRAMNUM on usb31 version */
+		size = DWC3_IP_IS(DWC3) ? 0 :
+			dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(num >> 1)) &
+				   DWC31_GTXFIFOSIZ_TXFRAMNUM;
+
+		dwc3_writel(dwc->regs, DWC3_GTXFIFOSIZ(num >> 1), size);
+	}
+	dwc->num_ep_resized = 0;
+}
+
+/*
+ * dwc3_gadget_resize_tx_fifos - reallocate fifo spaces for current use-case
+ * @dwc: pointer to our context structure
+ *
+ * This function will a best effort FIFO allocation in order
+ * to improve FIFO usage and throughput, while still allowing
+ * us to enable as many endpoints as possible.
+ *
+ * Keep in mind that this operation will be highly dependent
+ * on the configured size for RAM1 - which contains TxFifo -,
+ * the amount of endpoints enabled on coreConsultant tool, and
+ * the width of the Master Bus.
+ *
+ * In general, FIFO depths are represented with the following equation:
+ *
+ * fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1
+ *
+ * In conjunction with dwc3_gadget_check_config(), this resizing logic will
+ * ensure that all endpoints will have enough internal memory for one max
+ * packet per endpoint.
+ */
+static int dwc3_gadget_resize_tx_fifos(struct dwc3_ep *dep)
+{
+	struct dwc3 *dwc = dep->dwc;
+	int fifo_0_start;
+	int ram1_depth;
+	int fifo_size;
+	int min_depth;
+	int num_in_ep;
+	int remaining;
+	int num_fifos = 1;
+	int fifo;
+	int tmp;
+
+	if (!dwc->do_fifo_resize)
+		return 0;
+
+	/* resize IN endpoints except ep0 */
+	if (!usb_endpoint_dir_in(dep->endpoint.desc) || dep->number <= 1)
+		return 0;
 
+

drivers/usb/dwc3/gadget.c +44 -0

+	/*
+	 * We've already reserved 1 FIFO per EP, so check what we can fit in
+	 * addition to it.  If there is not enough remaining space, allocate
+	 * all the remaining space to the EP.
+	 */
+	fifo_size = (num_fifos - 1) * fifo;
+	if (remaining < fifo_size)
+		fifo_size = remaining;
+
+	fifo_size += fifo;
+	/* Last increment according to the TX FIFO size equation */
+	fifo_size++;
+
+	/* Check if TXFIFOs start at non-zero addr */
+	tmp = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0));
+	fifo_0_start = DWC3_GTXFIFOSIZ_TXFSTADDR(tmp);
+
+	fifo_size |= (fifo_0_start + (dwc->last_fifo_depth << 16));
+	if (DWC3_IP_IS(DWC3))
+		dwc->last_fifo_depth += DWC3_GTXFIFOSIZ_TXFDEP(fifo_size);
+	else
+		dwc->last_fifo_depth += DWC31_GTXFIFOSIZ_TXFDEP(fifo_size);
+
+	/* Check fifo size allocation doesn't exceed available RAM size. */
+	if (dwc->last_fifo_depth >= ram1_depth) {
+		dev_err(dwc->dev, "Fifosize(%d) > RAM size(%d) %s depth:%d\n",
+			dwc->last_fifo_depth, ram1_depth,
+			dep->endpoint.name, fifo_size);
+		if (DWC3_IP_IS(DWC3))
+			fifo_size = DWC3_GTXFIFOSIZ_TXFDEP(fifo_size);
+		else
+			fifo_size = DWC31_GTXFIFOSIZ_TXFDEP(fifo_size);
+
+		dwc->last_fifo_depth -= fifo_size;
+		return -ENOMEM;
+	}
+
+	dwc3_writel(dwc->regs, DWC3_GTXFIFOSIZ(dep->number >> 1), fifo_size);
+	dwc->num_ep_resized++;
+
+	return 0;
+}
+
+/**
  * __dwc3_gadget_ep_enable - initializes a hw endpoint
  * @dep: endpoint to be initialized

* @action: one of INIT, MODIFY or RESTORE

drivers/usb/dwc3/gadget.c +50 -0

@@ -648,6 +829,10 @@ static int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action)
 	int			ret;
 
 	if (!(dep->flags & DWC3_EP_ENABLED)) {
+		ret = dwc3_gadget_resize_tx_fifos(dep);
+		if (ret)
+			return ret;
+
 		ret = dwc3_gadget_start_config(dep);
 		if (ret)
 			return ret;

@@ -2498,6 +2683,7 @@ static int dwc3_gadget_stop(struct usb_gadget *g)
 
 	spin_lock_irqsave(&dwc->lock, flags);
 	dwc->gadget_driver	= NULL;
+	dwc->max_cfg_eps = 0;
 	spin_unlock_irqrestore(&dwc->lock, flags);
 
 	free_irq(dwc->irq_gadget, dwc->ev_buf);

@@ -2585,6 +2771,51 @@ static int dwc3_gadget_vbus_draw(struct usb_gadget *g, unsigned int mA)
 	return ret;
 }
 
+/**
+ * dwc3_gadget_check_config - ensure dwc3 can support the USB configuration
+ * @g: pointer to the USB gadget
+ *
+ * Used to record the maximum number of endpoints being used in a USB composite
+ * device. (across all configurations)  This is to be used in the calculation
+ * of the TXFIFO sizes when resizing internal memory for individual endpoints.
+ * It will help ensured that the resizing logic reserves enough space for at
+ * least one max packet.
+ */
+static int dwc3_gadget_check_config(struct usb_gadget *g)
+{
+	struct dwc3 *dwc = gadget_to_dwc(g);
+	struct usb_ep *ep;
+	int fifo_size = 0;
+	int ram1_depth;
+	int ep_num = 0;
+
+	if (!dwc->do_fifo_resize)
+		return 0;
+
+	list_for_each_entry(ep, &g->ep_list, ep_list) {
+		/* Only interested in the IN endpoints */
+		if (ep->claimed && (ep->address & USB_DIR_IN))
+			ep_num++;
+	}
+
+	if (ep_num <= dwc->max_cfg_eps)
+		return 0;
+
+	/* Update the max number of eps in the composition */
+	dwc->max_cfg_eps = ep_num;
+
+	fifo_size = dwc3_gadget_calc_tx_fifo_size(dwc, dwc->max_cfg_eps);
+	/* Based on the equation, increment by one for every ep */
+	fifo_size += dwc->max_cfg_eps;
+
+	/* Check if we can fit a single fifo per endpoint */
+	ram1_depth = DWC3_RAM1_DEPTH(dwc->hwparams.hwparams7);
+	if (fifo_size > ram1_depth)
+		return -ENOMEM;
+
+	return 0;
+}
+
 static const struct usb_gadget_ops dwc3_gadget_ops = {
 	.get_frame		= dwc3_gadget_get_frame,
 	.wakeup			= dwc3_gadget_wakeup,

Quoted 51 lines · Wesley Cheng

Some devices have USB compositions which may require multiple endpoints that support EP bursting. HW defined TX FIFO sizes may not always be sufficient for these compositions. By utilizing flexible TX FIFO allocation, this allows for endpoints to request the required FIFO depth to achieve higher bandwidth. With some higher bMaxBurst configurations, using a larger TX FIFO size results in better TX throughput.

By introducing the check_config() callback, the resizing logic can fetch the maximum number of endpoints used in the USB composition (can contain multiple configurations), which helps ensure that the resizing logic can fulfill the configuration(s), or return an error to the gadget layer otherwise during bind time.

Signed-off-by Wesley Cheng <[email protected]>

---
 drivers/usb/dwc3/core.c   |  15 +++
 drivers/usb/dwc3/core.h   |  16 ++++
 drivers/usb/dwc3/ep0.c    |   2 +
 drivers/usb/dwc3/gadget.c | 232 ++++++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 265 insertions(+)

drivers/usb/dwc3/core.c +8 -0

index ba74ad7..b194aecd 100644
@@ -1267,6 +1267,7 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 	u8			rx_max_burst_prd;
 	u8			tx_thr_num_pkt_prd;
 	u8			tx_max_burst_prd;
+	u8			tx_fifo_resize_max_num;
 	const char		*usb_psy_name;
 	int			ret;
 

@@ -1282,6 +1283,13 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 	 */
 	hird_threshold = 12;
 
+	/*
+	 * default to a TXFIFO size large enough to fit 6 max packets.  This
+	 * allows for systems with larger bus latencies to have some headroom
+	 * for endpoints that have a large bMaxBurst value.
+	 */
+	tx_fifo_resize_max_num = 6;
+
 	dwc->maximum_speed = usb_get_maximum_speed(dev);
 	dwc->max_ssp_rate = usb_get_maximum_ssp_rate(dev);
 	dwc->dr_mode = usb_get_dr_mode(dev);

@@ -1325,6 +1333,11 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 				&tx_thr_num_pkt_prd);
 	device_property_read_u8(dev, "snps,tx-max-burst-prd",
 				&tx_max_burst_prd);

drivers/usb/dwc3/core.c static void dwc3_get_properties(struct dwc3 *dwc) · line 1340

Quoted 5 lines

drivers/usb/dwc3/core.c +5 -0

+	dwc->do_fifo_resize = device_property_read_bool(dev,
+							"tx-fifo-resize");
+	if (dwc->do_fifo_resize)
+		device_property_read_u8(dev, "tx-fifo-max-num",
+					&tx_fifo_resize_max_num);

Why is this check here? The dwc->tx_fifo_resize_max_num should store whatever property the user sets. Whether the driver wants to use this

property should depend on "dwc->do_fifo_resize". Also why don't we have "snps," prefix to be consistent with the other properties?

Can we enforce to a single property? If the designer wants to enable this feature, he/she can to provide the tx-fifo-max-num. This would simplify the driver a bit. Since this is to optimize for performance, the user should know/want/test the specific value if they want to set for their setup and not hoping that the default setting not break their setup. So we can remove the "do_fifo_resize" property and just check whether tx_fifo_resize_max_num is set.

Quoted 211 lines

drivers/usb/dwc3/core.h +16 -0

index dccdf13..735e9be 100644
@@ -1023,6 +1023,7 @@ struct dwc3_scratchpad_array {
  * @rx_max_burst_prd: max periodic ESS receive burst size
  * @tx_thr_num_pkt_prd: periodic ESS transmit packet count
  * @tx_max_burst_prd: max periodic ESS transmit burst size
+ * @tx_fifo_resize_max_num: max number of fifos allocated during txfifo resize
  * @hsphy_interface: "utmi" or "ulpi"
  * @connected: true when we're connected to a host, false otherwise
  * @delayed_status: true when gadget driver asks for delayed status

@@ -1037,6 +1038,7 @@ struct dwc3_scratchpad_array {
  *	1	- utmi_l1_suspend_n
  * @is_fpga: true when we are using the FPGA board
  * @pending_events: true when we have pending IRQs to be handled
+ * @do_fifo_resize: true when txfifo resizing is enabled for dwc3 endpoints
  * @pullups_connected: true when Run/Stop bit is set
  * @setup_packet_pending: true when there's a Setup Packet in FIFO. Workaround
  * @three_stage_setup: set if we perform a three phase setup

@@ -1079,6 +1081,11 @@ struct dwc3_scratchpad_array {
  * @dis_split_quirk: set to disable split boundary.
  * @imod_interval: set the interrupt moderation interval in 250ns
  *			increments or 0 to disable.
+ * @max_cfg_eps: current max number of IN eps used across all USB configs.
+ * @last_fifo_depth: last fifo depth used to determine next fifo ram start
+ *		     address.
+ * @num_ep_resized: carries the current number endpoints which have had its tx
+ *		    fifo resized.
  */
 struct dwc3 {
 	struct work_struct	drd_work;

@@ -1233,6 +1240,7 @@ struct dwc3 {
 	u8			rx_max_burst_prd;
 	u8			tx_thr_num_pkt_prd;
 	u8			tx_max_burst_prd;
+	u8			tx_fifo_resize_max_num;
 
 	const char		*hsphy_interface;
 

@@ -1246,6 +1254,7 @@ struct dwc3 {
 	unsigned		is_utmi_l1_suspend:1;
 	unsigned		is_fpga:1;
 	unsigned		pending_events:1;
+	unsigned		do_fifo_resize:1;
 	unsigned		pullups_connected:1;
 	unsigned		setup_packet_pending:1;
 	unsigned		three_stage_setup:1;

@@ -1281,6 +1290,10 @@ struct dwc3 {
 	unsigned		dis_split_quirk:1;
 
 	u16			imod_interval;
+
+	int			max_cfg_eps;
+	int			last_fifo_depth;
+	int			num_ep_resized;
 };
 
 #define INCRX_BURST_MODE 0

@@ -1512,6 +1525,7 @@ int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned int cmd,
 		struct dwc3_gadget_ep_cmd_params *params);
 int dwc3_send_gadget_generic_command(struct dwc3 *dwc, unsigned int cmd,
 		u32 param);
+void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc);
 #else
 static inline int dwc3_gadget_init(struct dwc3 *dwc)
 { return 0; }

@@ -1531,6 +1545,8 @@ static inline int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned int cmd,
 static inline int dwc3_send_gadget_generic_command(struct dwc3 *dwc,
 		int cmd, u32 param)
 { return 0; }
+static inline void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc)
+{ }
 #endif
 
 #if IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE)

drivers/usb/dwc3/ep0.c +2 -0

index 3cd2942..d28d085 100644
@@ -619,6 +619,8 @@ static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl)
 		return -EINVAL;
 
 	case USB_STATE_ADDRESS:
+		dwc3_gadget_clear_tx_fifos(dwc);
+
 		ret = dwc3_ep0_delegate_req(dwc, ctrl);
 		/* if the cfg matches and the cfg is non zero */
 		if (cfg && (!ret || (ret == USB_GADGET_DELAYED_STATUS))) {

drivers/usb/dwc3/gadget.c +114 -0

index af6d7f1..e56f1a6 100644
@@ -632,6 +632,187 @@ static void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force,
 		bool interrupt);
 
 /**
+ * dwc3_gadget_calc_tx_fifo_size - calculates the txfifo size value
+ * @dwc: pointer to the DWC3 context
+ * @nfifos: number of fifos to calculate for
+ *
+ * Calculates the size value based on the equation below:
+ *
+ * DWC3 revision 280A and prior:
+ * fifo_size = mult * (max_packet / mdwidth) + 1;
+ *
+ * DWC3 revision 290A and onwards:
+ * fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1
+ *
+ * The max packet size is set to 1024, as the txfifo requirements mainly apply
+ * to super speed USB use cases.  However, it is safe to overestimate the fifo
+ * allocations for other scenarios, i.e. high speed USB.
+ */
+static int dwc3_gadget_calc_tx_fifo_size(struct dwc3 *dwc, int mult)
+{
+	int max_packet = 1024;
+	int fifo_size;
+	int mdwidth;
+
+	mdwidth = dwc3_mdwidth(dwc);
+
+	/* MDWIDTH is represented in bits, we need it in bytes */
+	mdwidth >>= 3;
+
+	if (DWC3_VER_IS_PRIOR(DWC3, 290A))
+		fifo_size = mult * (max_packet / mdwidth) + 1;
+	else
+		fifo_size = mult * ((max_packet + mdwidth) / mdwidth) + 1;
+	return fifo_size;
+}
+
+/**
+ * dwc3_gadget_clear_tx_fifo_size - Clears txfifo allocation
+ * @dwc: pointer to the DWC3 context
+ *
+ * Iterates through all the endpoint registers and clears the previous txfifo
+ * allocations.
+ */
+void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc)
+{
+	struct dwc3_ep *dep;
+	int fifo_depth;
+	int size;
+	int num;
+
+	if (!dwc->do_fifo_resize)
+		return;
+
+	/* Read ep0IN related TXFIFO size */
+	dep = dwc->eps[1];
+	size = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0));
+	if (DWC3_IP_IS(DWC3))
+		fifo_depth = DWC3_GTXFIFOSIZ_TXFDEP(size);
+	else
+		fifo_depth = DWC31_GTXFIFOSIZ_TXFDEP(size);
+
+	dwc->last_fifo_depth = fifo_depth;
+	/* Clear existing TXFIFO for all IN eps except ep0 */
+	for (num = 3; num < min_t(int, dwc->num_eps, DWC3_ENDPOINTS_NUM);
+	     num += 2) {
+		dep = dwc->eps[num];
+		/* Don't change TXFRAMNUM on usb31 version */
+		size = DWC3_IP_IS(DWC3) ? 0 :
+			dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(num >> 1)) &
+				   DWC31_GTXFIFOSIZ_TXFRAMNUM;
+
+		dwc3_writel(dwc->regs, DWC3_GTXFIFOSIZ(num >> 1), size);
+	}
+	dwc->num_ep_resized = 0;
+}
+
+/*
+ * dwc3_gadget_resize_tx_fifos - reallocate fifo spaces for current use-case
+ * @dwc: pointer to our context structure
+ *
+ * This function will a best effort FIFO allocation in order
+ * to improve FIFO usage and throughput, while still allowing
+ * us to enable as many endpoints as possible.
+ *
+ * Keep in mind that this operation will be highly dependent
+ * on the configured size for RAM1 - which contains TxFifo -,
+ * the amount of endpoints enabled on coreConsultant tool, and
+ * the width of the Master Bus.
+ *
+ * In general, FIFO depths are represented with the following equation:
+ *
+ * fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1
+ *
+ * In conjunction with dwc3_gadget_check_config(), this resizing logic will
+ * ensure that all endpoints will have enough internal memory for one max
+ * packet per endpoint.
+ */
+static int dwc3_gadget_resize_tx_fifos(struct dwc3_ep *dep)
+{
+	struct dwc3 *dwc = dep->dwc;
+	int fifo_0_start;
+	int ram1_depth;
+	int fifo_size;
+	int min_depth;
+	int num_in_ep;
+	int remaining;
+	int num_fifos = 1;
+	int fifo;
+	int tmp;
+
+	if (!dwc->do_fifo_resize)
+		return 0;
+
+	/* resize IN endpoints except ep0 */
+	if (!usb_endpoint_dir_in(dep->endpoint.desc) || dep->number <= 1)
+		return 0;

drivers/usb/dwc3/gadget.c static void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force, · line 759

Quoted 11 lines

drivers/usb/dwc3/gadget.c +11 -0

+
+	ram1_depth = DWC3_RAM1_DEPTH(dwc->hwparams.hwparams7);
+
+	if ((dep->endpoint.maxburst > 1 &&
+	     usb_endpoint_xfer_bulk(dep->endpoint.desc)) ||
+	    usb_endpoint_xfer_isoc(dep->endpoint.desc))
+		num_fifos = 3;
+
+	if (dep->endpoint.maxburst > 6 &&
+	    usb_endpoint_xfer_bulk(dep->endpoint.desc) && DWC3_IP_IS(DWC31))
+		num_fifos = dwc->tx_fifo_resize_max_num;

Why only bulk? Isoc should be at least equal or more than bulk. Also, make this applicable to DWC_usb32 also.

Quoted 23 lines

drivers/usb/dwc3/gadget.c +5 -0

@@ -648,6 +829,10 @@ static int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action)
 	int			ret;
 
 	if (!(dep->flags & DWC3_EP_ENABLED)) {
+		ret = dwc3_gadget_resize_tx_fifos(dep);
+		if (ret)
+			return ret;
+
 		ret = dwc3_gadget_start_config(dep);
 		if (ret)
 			return ret;

@@ -2498,6 +2683,7 @@ static int dwc3_gadget_stop(struct usb_gadget *g)
 
 	spin_lock_irqsave(&dwc->lock, flags);
 	dwc->gadget_driver	= NULL;
+	dwc->max_cfg_eps = 0;
 	spin_unlock_irqrestore(&dwc->lock, flags);
 
 	free_irq(dwc->irq_gadget, dwc->ev_buf);

@@ -2585,6 +2771,51 @@ static int dwc3_gadget_vbus_draw(struct usb_gadget *g, unsigned int mA)
 	return ret;
 }
 

drivers/usb/dwc3/gadget.c static int dwc3_gadget_vbus_draw(struct usb_gadget *g, unsigned int mA) · line 2784

Quoted 11 lines

drivers/usb/dwc3/gadget.c +11 -0

+/**
+ * dwc3_gadget_check_config - ensure dwc3 can support the USB configuration
+ * @g: pointer to the USB gadget
+ *
+ * Used to record the maximum number of endpoints being used in a USB composite
+ * device. (across all configurations)  This is to be used in the calculation
+ * of the TXFIFO sizes when resizing internal memory for individual endpoints.
+ * It will help ensured that the resizing logic reserves enough space for at
+ * least one max packet.
+ */
+static int dwc3_gadget_check_config(struct usb_gadget *g)

Hi,

Quoted 22 lines · Thinh Nguyen

Quoted 21 lines · Wesley Cheng

Some devices have USB compositions which may require multiple endpoints that support EP bursting. HW defined TX FIFO sizes may not always be sufficient for these compositions. By utilizing flexible TX FIFO allocation, this allows for endpoints to request the required FIFO depth to achieve higher bandwidth. With some higher bMaxBurst configurations, using a larger TX FIFO size results in better TX throughput.

By introducing the check_config() callback, the resizing logic can fetch the maximum number of endpoints used in the USB composition (can contain multiple configurations), which helps ensure that the resizing logic can fulfill the configuration(s), or return an error to the gadget layer otherwise during bind time.

Signed-off-by Wesley Cheng <[email protected]>

---
 drivers/usb/dwc3/core.c   |  15 +++
 drivers/usb/dwc3/core.h   |  16 ++++
 drivers/usb/dwc3/ep0.c    |   2 +
 drivers/usb/dwc3/gadget.c | 232 ++++++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 265 insertions(+)

Quoted 41 lines

Quoted 40 lines

drivers/usb/dwc3/gadget.c +40 -0

+/*
+ * dwc3_gadget_resize_tx_fifos - reallocate fifo spaces for current use-case
+ * @dwc: pointer to our context structure
+ *
+ * This function will a best effort FIFO allocation in order
+ * to improve FIFO usage and throughput, while still allowing
+ * us to enable as many endpoints as possible.
+ *
+ * Keep in mind that this operation will be highly dependent
+ * on the configured size for RAM1 - which contains TxFifo -,
+ * the amount of endpoints enabled on coreConsultant tool, and
+ * the width of the Master Bus.
+ *
+ * In general, FIFO depths are represented with the following equation:
+ *
+ * fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1
+ *
+ * In conjunction with dwc3_gadget_check_config(), this resizing logic will
+ * ensure that all endpoints will have enough internal memory for one max
+ * packet per endpoint.
+ */
+static int dwc3_gadget_resize_tx_fifos(struct dwc3_ep *dep)
+{
+	struct dwc3 *dwc = dep->dwc;
+	int fifo_0_start;
+	int ram1_depth;
+	int fifo_size;
+	int min_depth;
+	int num_in_ep;
+	int remaining;
+	int num_fifos = 1;
+	int fifo;
+	int tmp;
+
+	if (!dwc->do_fifo_resize)
+		return 0;
+
+	/* resize IN endpoints except ep0 */
+	if (!usb_endpoint_dir_in(dep->endpoint.desc) || dep->number <= 1)
+		return 0;

Quoted 14 lines

drivers/usb/dwc3/gadget.c static void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force, · line 759

Quoted 11 lines

drivers/usb/dwc3/gadget.c +11 -0

+
+	ram1_depth = DWC3_RAM1_DEPTH(dwc->hwparams.hwparams7);
+
+	if ((dep->endpoint.maxburst > 1 &&
+	     usb_endpoint_xfer_bulk(dep->endpoint.desc)) ||
+	    usb_endpoint_xfer_isoc(dep->endpoint.desc))
+		num_fifos = 3;
+
+	if (dep->endpoint.maxburst > 6 &&
+	    usb_endpoint_xfer_bulk(dep->endpoint.desc) && DWC3_IP_IS(DWC31))
+		num_fifos = dwc->tx_fifo_resize_max_num;

Why only bulk? Isoc should be at least equal or more than bulk. Also, make this applicable to DWC_usb32 also.

this should be applicable to all DWC3 versions, no? dwc3, 31 and 32.

Hi,

Quoted 52 lines · Thinh Nguyen

Quoted 51 lines · Wesley Cheng

Some devices have USB compositions which may require multiple endpoints that support EP bursting. HW defined TX FIFO sizes may not always be sufficient for these compositions. By utilizing flexible TX FIFO allocation, this allows for endpoints to request the required FIFO depth to achieve higher bandwidth. With some higher bMaxBurst configurations, using a larger TX FIFO size results in better TX throughput.

By introducing the check_config() callback, the resizing logic can fetch the maximum number of endpoints used in the USB composition (can contain multiple configurations), which helps ensure that the resizing logic can fulfill the configuration(s), or return an error to the gadget layer otherwise during bind time.

Signed-off-by Wesley Cheng <[email protected]>

---
 drivers/usb/dwc3/core.c   |  15 +++
 drivers/usb/dwc3/core.h   |  16 ++++
 drivers/usb/dwc3/ep0.c    |   2 +
 drivers/usb/dwc3/gadget.c | 232 ++++++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 265 insertions(+)

drivers/usb/dwc3/core.c +8 -0

index ba74ad7..b194aecd 100644
@@ -1267,6 +1267,7 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 	u8			rx_max_burst_prd;
 	u8			tx_thr_num_pkt_prd;
 	u8			tx_max_burst_prd;
+	u8			tx_fifo_resize_max_num;
 	const char		*usb_psy_name;
 	int			ret;
 

@@ -1282,6 +1283,13 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 	 */
 	hird_threshold = 12;
 
+	/*
+	 * default to a TXFIFO size large enough to fit 6 max packets.  This
+	 * allows for systems with larger bus latencies to have some headroom
+	 * for endpoints that have a large bMaxBurst value.
+	 */
+	tx_fifo_resize_max_num = 6;
+
 	dwc->maximum_speed = usb_get_maximum_speed(dev);
 	dwc->max_ssp_rate = usb_get_maximum_ssp_rate(dev);
 	dwc->dr_mode = usb_get_dr_mode(dev);

@@ -1325,6 +1333,11 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 				&tx_thr_num_pkt_prd);
 	device_property_read_u8(dev, "snps,tx-max-burst-prd",
 				&tx_max_burst_prd);

Quoted 8 lines

drivers/usb/dwc3/core.c static void dwc3_get_properties(struct dwc3 *dwc) · line 1340

Quoted 5 lines

drivers/usb/dwc3/core.c +5 -0

+	dwc->do_fifo_resize = device_property_read_bool(dev,
+							"tx-fifo-resize");
+	if (dwc->do_fifo_resize)
+		device_property_read_u8(dev, "tx-fifo-max-num",
+					&tx_fifo_resize_max_num);

Why is this check here? The dwc->tx_fifo_resize_max_num should store whatever property the user sets. Whether the driver wants to use this

Ack!

Quoted 2 lines

property should depend on "dwc->do_fifo_resize". Also why don't we have "snps," prefix to be consistent with the other properties?

Ack!

Quoted 7 lines

Can we enforce to a single property? If the designer wants to enable this feature, he/she can to provide the tx-fifo-max-num. This would simplify the driver a bit. Since this is to optimize for performance, the user should know/want/test the specific value if they want to set for their setup and not hoping that the default setting not break their setup. So we can remove the "do_fifo_resize" property and just check whether tx_fifo_resize_max_num is set.

Ack!

All very valid points :-)

Quoted 77 lines

Quoted 52 lines · Thinh Nguyen

Quoted 51 lines · Wesley Cheng

Some devices have USB compositions which may require multiple endpoints that support EP bursting. HW defined TX FIFO sizes may not always be sufficient for these compositions. By utilizing flexible TX FIFO allocation, this allows for endpoints to request the required FIFO depth to achieve higher bandwidth. With some higher bMaxBurst configurations, using a larger TX FIFO size results in better TX throughput.

By introducing the check_config() callback, the resizing logic can fetch the maximum number of endpoints used in the USB composition (can contain multiple configurations), which helps ensure that the resizing logic can fulfill the configuration(s), or return an error to the gadget layer otherwise during bind time.

Signed-off-by Wesley Cheng <[email protected]>

---
 drivers/usb/dwc3/core.c   |  15 +++
 drivers/usb/dwc3/core.h   |  16 ++++
 drivers/usb/dwc3/ep0.c    |   2 +
 drivers/usb/dwc3/gadget.c | 232 ++++++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 265 insertions(+)

drivers/usb/dwc3/core.c +8 -0

index ba74ad7..b194aecd 100644
@@ -1267,6 +1267,7 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 	u8			rx_max_burst_prd;
 	u8			tx_thr_num_pkt_prd;
 	u8			tx_max_burst_prd;
+	u8			tx_fifo_resize_max_num;
 	const char		*usb_psy_name;
 	int			ret;
 

@@ -1282,6 +1283,13 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 	 */
 	hird_threshold = 12;
 
+	/*
+	 * default to a TXFIFO size large enough to fit 6 max packets.  This
+	 * allows for systems with larger bus latencies to have some headroom
+	 * for endpoints that have a large bMaxBurst value.
+	 */
+	tx_fifo_resize_max_num = 6;
+
 	dwc->maximum_speed = usb_get_maximum_speed(dev);
 	dwc->max_ssp_rate = usb_get_maximum_ssp_rate(dev);
 	dwc->dr_mode = usb_get_dr_mode(dev);

@@ -1325,6 +1333,11 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 				&tx_thr_num_pkt_prd);
 	device_property_read_u8(dev, "snps,tx-max-burst-prd",
 				&tx_max_burst_prd);

Quoted 8 lines

drivers/usb/dwc3/core.c static void dwc3_get_properties(struct dwc3 *dwc) · line 1340

Quoted 5 lines

drivers/usb/dwc3/core.c +5 -0

+	dwc->do_fifo_resize = device_property_read_bool(dev,
+							"tx-fifo-resize");
+	if (dwc->do_fifo_resize)
+		device_property_read_u8(dev, "tx-fifo-max-num",
+					&tx_fifo_resize_max_num);

Why is this check here? The dwc->tx_fifo_resize_max_num should store whatever property the user sets. Whether the driver wants to use this

Ack!

Quoted 2 lines

property should depend on "dwc->do_fifo_resize". Also why don't we have "snps," prefix to be consistent with the other properties?

Ack!

Quoted 7 lines

Can we enforce to a single property? If the designer wants to enable this feature, he/she can to provide the tx-fifo-max-num. This would simplify the driver a bit. Since this is to optimize for performance, the user should know/want/test the specific value if they want to set for their setup and not hoping that the default setting not break their setup. So we can remove the "do_fifo_resize" property and just check whether tx_fifo_resize_max_num is set.

Quoted 4 lines

Ack!

All very valid points :-)

Looks like this series already landed in Greg's testing branch. Not sure how we usually handle this to address some of our concerns. Add fix patches on top of Greg's testing branch?

Hi,

Quoted 79 lines · Thinh Nguyen

Quoted 79 lines

Quoted 52 lines · Thinh Nguyen

Quoted 51 lines · Wesley Cheng

Some devices have USB compositions which may require multiple endpoints that support EP bursting. HW defined TX FIFO sizes may not always be sufficient for these compositions. By utilizing flexible TX FIFO allocation, this allows for endpoints to request the required FIFO depth to achieve higher bandwidth. With some higher bMaxBurst configurations, using a larger TX FIFO size results in better TX throughput.

By introducing the check_config() callback, the resizing logic can fetch the maximum number of endpoints used in the USB composition (can contain multiple configurations), which helps ensure that the resizing logic can fulfill the configuration(s), or return an error to the gadget layer otherwise during bind time.

Signed-off-by Wesley Cheng <[email protected]>

---
 drivers/usb/dwc3/core.c   |  15 +++
 drivers/usb/dwc3/core.h   |  16 ++++
 drivers/usb/dwc3/ep0.c    |   2 +
 drivers/usb/dwc3/gadget.c | 232 ++++++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 265 insertions(+)

drivers/usb/dwc3/core.c +8 -0

index ba74ad7..b194aecd 100644
@@ -1267,6 +1267,7 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 	u8			rx_max_burst_prd;
 	u8			tx_thr_num_pkt_prd;
 	u8			tx_max_burst_prd;
+	u8			tx_fifo_resize_max_num;
 	const char		*usb_psy_name;
 	int			ret;
 

@@ -1282,6 +1283,13 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 	 */
 	hird_threshold = 12;
 
+	/*
+	 * default to a TXFIFO size large enough to fit 6 max packets.  This
+	 * allows for systems with larger bus latencies to have some headroom
+	 * for endpoints that have a large bMaxBurst value.
+	 */
+	tx_fifo_resize_max_num = 6;
+
 	dwc->maximum_speed = usb_get_maximum_speed(dev);
 	dwc->max_ssp_rate = usb_get_maximum_ssp_rate(dev);
 	dwc->dr_mode = usb_get_dr_mode(dev);

@@ -1325,6 +1333,11 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 				&tx_thr_num_pkt_prd);
 	device_property_read_u8(dev, "snps,tx-max-burst-prd",
 				&tx_max_burst_prd);

Quoted 8 lines

drivers/usb/dwc3/core.c static void dwc3_get_properties(struct dwc3 *dwc) · line 1340

Quoted 5 lines

drivers/usb/dwc3/core.c +5 -0

+	dwc->do_fifo_resize = device_property_read_bool(dev,
+							"tx-fifo-resize");
+	if (dwc->do_fifo_resize)
+		device_property_read_u8(dev, "tx-fifo-max-num",
+					&tx_fifo_resize_max_num);

Why is this check here? The dwc->tx_fifo_resize_max_num should store whatever property the user sets. Whether the driver wants to use this

Ack!

Quoted 2 lines

property should depend on "dwc->do_fifo_resize". Also why don't we have "snps," prefix to be consistent with the other properties?

Ack!

Quoted 7 lines

Can we enforce to a single property? If the designer wants to enable this feature, he/she can to provide the tx-fifo-max-num. This would simplify the driver a bit. Since this is to optimize for performance, the user should know/want/test the specific value if they want to set for their setup and not hoping that the default setting not break their setup. So we can remove the "do_fifo_resize" property and just check whether tx_fifo_resize_max_num is set.

Ack!

Quoted 6 lines

Quoted 2 lines

All very valid points :-)

Looks like this series already landed in Greg's testing branch. Not sure how we usually handle this to address some of our concerns. Add fix patches on top of Greg's testing branch?

yup, no choice anymore :-(

Hi,

Quoted 81 lines · Thinh Nguyen

Quoted 81 lines

Quoted 52 lines · Thinh Nguyen

Quoted 51 lines · Wesley Cheng

Some devices have USB compositions which may require multiple endpoints that support EP bursting. HW defined TX FIFO sizes may not always be sufficient for these compositions. By utilizing flexible TX FIFO allocation, this allows for endpoints to request the required FIFO depth to achieve higher bandwidth. With some higher bMaxBurst configurations, using a larger TX FIFO size results in better TX throughput.

By introducing the check_config() callback, the resizing logic can fetch the maximum number of endpoints used in the USB composition (can contain multiple configurations), which helps ensure that the resizing logic can fulfill the configuration(s), or return an error to the gadget layer otherwise during bind time.

Signed-off-by Wesley Cheng <[email protected]>

---
 drivers/usb/dwc3/core.c   |  15 +++
 drivers/usb/dwc3/core.h   |  16 ++++
 drivers/usb/dwc3/ep0.c    |   2 +
 drivers/usb/dwc3/gadget.c | 232 ++++++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 265 insertions(+)

drivers/usb/dwc3/core.c +8 -0

index ba74ad7..b194aecd 100644
@@ -1267,6 +1267,7 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 	u8			rx_max_burst_prd;
 	u8			tx_thr_num_pkt_prd;
 	u8			tx_max_burst_prd;
+	u8			tx_fifo_resize_max_num;
 	const char		*usb_psy_name;
 	int			ret;
 

@@ -1282,6 +1283,13 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 	 */
 	hird_threshold = 12;
 
+	/*
+	 * default to a TXFIFO size large enough to fit 6 max packets.  This
+	 * allows for systems with larger bus latencies to have some headroom
+	 * for endpoints that have a large bMaxBurst value.
+	 */
+	tx_fifo_resize_max_num = 6;
+
 	dwc->maximum_speed = usb_get_maximum_speed(dev);
 	dwc->max_ssp_rate = usb_get_maximum_ssp_rate(dev);
 	dwc->dr_mode = usb_get_dr_mode(dev);

@@ -1325,6 +1333,11 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 				&tx_thr_num_pkt_prd);
 	device_property_read_u8(dev, "snps,tx-max-burst-prd",
 				&tx_max_burst_prd);

Quoted 8 lines

drivers/usb/dwc3/core.c static void dwc3_get_properties(struct dwc3 *dwc) · line 1340

Quoted 5 lines

drivers/usb/dwc3/core.c +5 -0

+	dwc->do_fifo_resize = device_property_read_bool(dev,
+							"tx-fifo-resize");
+	if (dwc->do_fifo_resize)
+		device_property_read_u8(dev, "tx-fifo-max-num",
+					&tx_fifo_resize_max_num);

Why is this check here? The dwc->tx_fifo_resize_max_num should store whatever property the user sets. Whether the driver wants to use this

Ack!

Quoted 2 lines

property should depend on "dwc->do_fifo_resize". Also why don't we have "snps," prefix to be consistent with the other properties?

Ack!

Quoted 7 lines

Can we enforce to a single property? If the designer wants to enable this feature, he/she can to provide the tx-fifo-max-num. This would simplify the driver a bit. Since this is to optimize for performance, the user should know/want/test the specific value if they want to set for their setup and not hoping that the default setting not break their setup. So we can remove the "do_fifo_resize" property and just check whether tx_fifo_resize_max_num is set.

Ack!

All very valid points :-)

Quoted 4 lines

Looks like this series already landed in Greg's testing branch. Not sure how we usually handle this to address some of our concerns. Add fix patches on top of Greg's testing branch?

yup, no choice anymore :-(

Quoted 85 lines · Felipe Balbi

Hi,

Quoted 81 lines · Thinh Nguyen

Quoted 81 lines

Quoted 52 lines · Thinh Nguyen

Quoted 51 lines · Wesley Cheng

Some devices have USB compositions which may require multiple endpoints that support EP bursting. HW defined TX FIFO sizes may not always be sufficient for these compositions. By utilizing flexible TX FIFO allocation, this allows for endpoints to request the required FIFO depth to achieve higher bandwidth. With some higher bMaxBurst configurations, using a larger TX FIFO size results in better TX throughput.

By introducing the check_config() callback, the resizing logic can fetch the maximum number of endpoints used in the USB composition (can contain multiple configurations), which helps ensure that the resizing logic can fulfill the configuration(s), or return an error to the gadget layer otherwise during bind time.

Signed-off-by Wesley Cheng <[email protected]>

---
 drivers/usb/dwc3/core.c   |  15 +++
 drivers/usb/dwc3/core.h   |  16 ++++
 drivers/usb/dwc3/ep0.c    |   2 +
 drivers/usb/dwc3/gadget.c | 232 ++++++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 265 insertions(+)

drivers/usb/dwc3/core.c +8 -0

index ba74ad7..b194aecd 100644
@@ -1267,6 +1267,7 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 	u8			rx_max_burst_prd;
 	u8			tx_thr_num_pkt_prd;
 	u8			tx_max_burst_prd;
+	u8			tx_fifo_resize_max_num;
 	const char		*usb_psy_name;
 	int			ret;
 

@@ -1282,6 +1283,13 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 	 */
 	hird_threshold = 12;
 
+	/*
+	 * default to a TXFIFO size large enough to fit 6 max packets.  This
+	 * allows for systems with larger bus latencies to have some headroom
+	 * for endpoints that have a large bMaxBurst value.
+	 */
+	tx_fifo_resize_max_num = 6;
+
 	dwc->maximum_speed = usb_get_maximum_speed(dev);
 	dwc->max_ssp_rate = usb_get_maximum_ssp_rate(dev);
 	dwc->dr_mode = usb_get_dr_mode(dev);

@@ -1325,6 +1333,11 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 				&tx_thr_num_pkt_prd);
 	device_property_read_u8(dev, "snps,tx-max-burst-prd",
 				&tx_max_burst_prd);

Quoted 8 lines

drivers/usb/dwc3/core.c static void dwc3_get_properties(struct dwc3 *dwc) · line 1340

Quoted 5 lines

drivers/usb/dwc3/core.c +5 -0

+	dwc->do_fifo_resize = device_property_read_bool(dev,
+							"tx-fifo-resize");
+	if (dwc->do_fifo_resize)
+		device_property_read_u8(dev, "tx-fifo-max-num",
+					&tx_fifo_resize_max_num);

Why is this check here? The dwc->tx_fifo_resize_max_num should store whatever property the user sets. Whether the driver wants to use this

Ack!

Quoted 2 lines

property should depend on "dwc->do_fifo_resize". Also why don't we have "snps," prefix to be consistent with the other properties?

Ack!

Quoted 7 lines

Can we enforce to a single property? If the designer wants to enable this feature, he/she can to provide the tx-fifo-max-num. This would simplify the driver a bit. Since this is to optimize for performance, the user should know/want/test the specific value if they want to set for their setup and not hoping that the default setting not break their setup. So we can remove the "do_fifo_resize" property and just check whether tx_fifo_resize_max_num is set.

Ack!

All very valid points :-)

Hi Thinh/Felipe,

Quoted 5 lines

Quoted 4 lines

Looks like this series already landed in Greg's testing branch. Not sure how we usually handle this to address some of our concerns. Add fix patches on top of Greg's testing branch?

Quoted 2 lines

yup, no choice anymore :-(

Let me review your feedback, which had some good points. We can add a change addressing everything on top of what is merged on Greg's branch.

Quoted 96 lines · Wesley Cheng

Quoted 85 lines · Felipe Balbi

Hi,

Quoted 81 lines · Thinh Nguyen

Quoted 81 lines

Quoted 52 lines · Thinh Nguyen

Quoted 51 lines · Wesley Cheng

Some devices have USB compositions which may require multiple endpoints that support EP bursting. HW defined TX FIFO sizes may not always be sufficient for these compositions. By utilizing flexible TX FIFO allocation, this allows for endpoints to request the required FIFO depth to achieve higher bandwidth. With some higher bMaxBurst configurations, using a larger TX FIFO size results in better TX throughput.

By introducing the check_config() callback, the resizing logic can fetch the maximum number of endpoints used in the USB composition (can contain multiple configurations), which helps ensure that the resizing logic can fulfill the configuration(s), or return an error to the gadget layer otherwise during bind time.

Signed-off-by Wesley Cheng <[email protected]>

---
 drivers/usb/dwc3/core.c   |  15 +++
 drivers/usb/dwc3/core.h   |  16 ++++
 drivers/usb/dwc3/ep0.c    |   2 +
 drivers/usb/dwc3/gadget.c | 232 ++++++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 265 insertions(+)

drivers/usb/dwc3/core.c +8 -0

index ba74ad7..b194aecd 100644
@@ -1267,6 +1267,7 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 	u8			rx_max_burst_prd;
 	u8			tx_thr_num_pkt_prd;
 	u8			tx_max_burst_prd;
+	u8			tx_fifo_resize_max_num;
 	const char		*usb_psy_name;
 	int			ret;
 

@@ -1282,6 +1283,13 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 	 */
 	hird_threshold = 12;
 
+	/*
+	 * default to a TXFIFO size large enough to fit 6 max packets.  This
+	 * allows for systems with larger bus latencies to have some headroom
+	 * for endpoints that have a large bMaxBurst value.
+	 */
+	tx_fifo_resize_max_num = 6;
+
 	dwc->maximum_speed = usb_get_maximum_speed(dev);
 	dwc->max_ssp_rate = usb_get_maximum_ssp_rate(dev);
 	dwc->dr_mode = usb_get_dr_mode(dev);

@@ -1325,6 +1333,11 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 				&tx_thr_num_pkt_prd);
 	device_property_read_u8(dev, "snps,tx-max-burst-prd",
 				&tx_max_burst_prd);

Quoted 8 lines

drivers/usb/dwc3/core.c static void dwc3_get_properties(struct dwc3 *dwc) · line 1340

Quoted 5 lines

drivers/usb/dwc3/core.c +5 -0

+	dwc->do_fifo_resize = device_property_read_bool(dev,
+							"tx-fifo-resize");
+	if (dwc->do_fifo_resize)
+		device_property_read_u8(dev, "tx-fifo-max-num",
+					&tx_fifo_resize_max_num);

Why is this check here? The dwc->tx_fifo_resize_max_num should store whatever property the user sets. Whether the driver wants to use this

Ack!

Quoted 2 lines

property should depend on "dwc->do_fifo_resize". Also why don't we have "snps," prefix to be consistent with the other properties?

Ack!

Quoted 7 lines

Can we enforce to a single property? If the designer wants to enable this feature, he/she can to provide the tx-fifo-max-num. This would simplify the driver a bit. Since this is to optimize for performance, the user should know/want/test the specific value if they want to set for their setup and not hoping that the default setting not break their setup. So we can remove the "do_fifo_resize" property and just check whether tx_fifo_resize_max_num is set.

Ack!

All very valid points :-)

Hi Thinh/Felipe,

Quoted 5 lines

Quoted 4 lines

Looks like this series already landed in Greg's testing branch. Not sure how we usually handle this to address some of our concerns. Add fix patches on top of Greg's testing branch?

Quoted 5 lines

Quoted 2 lines

yup, no choice anymore :-(

Let me review your feedback, which had some good points. We can add a change addressing everything on top of what is merged on Greg's branch.

Any hint as to when these fixups will be sent?

Quoted 80 lines · Felipe Balbi

Hi,

Quoted 52 lines · Thinh Nguyen

Quoted 51 lines · Wesley Cheng

Some devices have USB compositions which may require multiple endpoints that support EP bursting. HW defined TX FIFO sizes may not always be sufficient for these compositions. By utilizing flexible TX FIFO allocation, this allows for endpoints to request the required FIFO depth to achieve higher bandwidth. With some higher bMaxBurst configurations, using a larger TX FIFO size results in better TX throughput.

By introducing the check_config() callback, the resizing logic can fetch the maximum number of endpoints used in the USB composition (can contain multiple configurations), which helps ensure that the resizing logic can fulfill the configuration(s), or return an error to the gadget layer otherwise during bind time.

Signed-off-by Wesley Cheng <[email protected]>

---
 drivers/usb/dwc3/core.c   |  15 +++
 drivers/usb/dwc3/core.h   |  16 ++++
 drivers/usb/dwc3/ep0.c    |   2 +
 drivers/usb/dwc3/gadget.c | 232 ++++++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 265 insertions(+)

drivers/usb/dwc3/core.c +8 -0

index ba74ad7..b194aecd 100644
@@ -1267,6 +1267,7 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 	u8			rx_max_burst_prd;
 	u8			tx_thr_num_pkt_prd;
 	u8			tx_max_burst_prd;
+	u8			tx_fifo_resize_max_num;
 	const char		*usb_psy_name;
 	int			ret;
 

@@ -1282,6 +1283,13 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 	 */
 	hird_threshold = 12;
 
+	/*
+	 * default to a TXFIFO size large enough to fit 6 max packets.  This
+	 * allows for systems with larger bus latencies to have some headroom
+	 * for endpoints that have a large bMaxBurst value.
+	 */
+	tx_fifo_resize_max_num = 6;
+
 	dwc->maximum_speed = usb_get_maximum_speed(dev);
 	dwc->max_ssp_rate = usb_get_maximum_ssp_rate(dev);
 	dwc->dr_mode = usb_get_dr_mode(dev);

@@ -1325,6 +1333,11 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 				&tx_thr_num_pkt_prd);
 	device_property_read_u8(dev, "snps,tx-max-burst-prd",
 				&tx_max_burst_prd);

Quoted 8 lines

drivers/usb/dwc3/core.c static void dwc3_get_properties(struct dwc3 *dwc) · line 1340

Quoted 5 lines

drivers/usb/dwc3/core.c +5 -0

+	dwc->do_fifo_resize = device_property_read_bool(dev,
+							"tx-fifo-resize");
+	if (dwc->do_fifo_resize)
+		device_property_read_u8(dev, "tx-fifo-max-num",
+					&tx_fifo_resize_max_num);

Why is this check here? The dwc->tx_fifo_resize_max_num should store whatever property the user sets. Whether the driver wants to use this

Ack!

Quoted 2 lines

property should depend on "dwc->do_fifo_resize". Also why don't we have "snps," prefix to be consistent with the other properties?

Ack!

Quoted 7 lines

Can we enforce to a single property? If the designer wants to enable this feature, he/she can to provide the tx-fifo-max-num. This would simplify the driver a bit. Since this is to optimize for performance, the user should know/want/test the specific value if they want to set for their setup and not hoping that the default setting not break their setup. So we can remove the "do_fifo_resize" property and just check whether tx_fifo_resize_max_num is set.

Quoted 4 lines

Ack!

All very valid points :-)

Looks like this series already landed in Greg's testing branch. Not sure how we usually handle this to address some of our concerns. Add fix patches on top of Greg's testing branch?

Hi,

Quoted 48 lines · Wesley Cheng

Some devices have USB compositions which may require multiple endpoints that support EP bursting. HW defined TX FIFO sizes may not always be sufficient for these compositions. By utilizing flexible TX FIFO allocation, this allows for endpoints to request the required FIFO depth to achieve higher bandwidth. With some higher bMaxBurst configurations, using a larger TX FIFO size results in better TX throughput.

By introducing the check_config() callback, the resizing logic can fetch the maximum number of endpoints used in the USB composition (can contain multiple configurations), which helps ensure that the resizing logic can fulfill the configuration(s), or return an error to the gadget layer otherwise during bind time.

Signed-off-by Wesley Cheng <[email protected]>

---
 drivers/usb/dwc3/core.c   |  15 +++
 drivers/usb/dwc3/core.h   |  16 ++++
 drivers/usb/dwc3/ep0.c    |   2 +
 drivers/usb/dwc3/gadget.c | 232 ++++++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 265 insertions(+)

drivers/usb/dwc3/core.c +8 -0

index ba74ad7..b194aecd 100644
@@ -1267,6 +1267,7 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 	u8			rx_max_burst_prd;
 	u8			tx_thr_num_pkt_prd;
 	u8			tx_max_burst_prd;
+	u8			tx_fifo_resize_max_num;
 	const char		*usb_psy_name;
 	int			ret;
 

@@ -1282,6 +1283,13 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 	 */
 	hird_threshold = 12;
 
+	/*
+	 * default to a TXFIFO size large enough to fit 6 max packets.  This
+	 * allows for systems with larger bus latencies to have some headroom
+	 * for endpoints that have a large bMaxBurst value.
+	 */
+	tx_fifo_resize_max_num = 6;
+
 	dwc->maximum_speed = usb_get_maximum_speed(dev);
 	dwc->max_ssp_rate = usb_get_maximum_ssp_rate(dev);
 	dwc->dr_mode = usb_get_dr_mode(dev);

drivers/usb/dwc3/core.c static void dwc3_get_properties(struct dwc3 *dwc) · line 1340

Quoted 8 lines

drivers/usb/dwc3/core.c +5 -0

@@ -1325,6 +1333,11 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 				&tx_thr_num_pkt_prd);
 	device_property_read_u8(dev, "snps,tx-max-burst-prd",
 				&tx_max_burst_prd);
+	dwc->do_fifo_resize = device_property_read_bool(dev,
+							"tx-fifo-resize");
+	if (dwc->do_fifo_resize)
+		device_property_read_u8(dev, "tx-fifo-max-num",
+					&tx_fifo_resize_max_num);

Why is this check here? The dwc->tx_fifo_resize_max_num should store whatever property the user sets. Whether the driver wants to use this property should depend on "dwc->do_fifo_resize". Also why don't we have "snps," prefix to be consistent with the other properties?

Can we enforce to a single property? If the designer wants to enable this feature, he/she can to provide the tx-fifo-max-num. This would simplify the driver a bit. Since this is to optimize for performance, the user should know/want/test the specific value if they want to set for their setup and not hoping that the default setting not break their setup. So we can remove the "do_fifo_resize" property and just check whether tx_fifo_resize_max_num is set.

drivers/usb/dwc3/core.c static void dwc3_get_properties(struct dwc3 *dwc) · line 1407

Quoted 9 lines

drivers/usb/dwc3/core.c +2 -0

 	dwc->disable_scramble_quirk = device_property_read_bool(dev,
 				"snps,disable_scramble_quirk");

@@ -1390,6 +1403,8 @@ static void dwc3_get_properties(struct dwc3 *dwc)
 	dwc->tx_max_burst_prd = tx_max_burst_prd;
 
 	dwc->imod_interval = 0;
+
+	dwc->tx_fifo_resize_max_num = tx_fifo_resize_max_num;

See comment above

Quoted 109 lines

drivers/usb/dwc3/core.c +0 -0

 }
 
 /* check whether the core supports IMOD */

drivers/usb/dwc3/core.h +16 -0

index dccdf13..735e9be 100644
@@ -1023,6 +1023,7 @@ struct dwc3_scratchpad_array {
  * @rx_max_burst_prd: max periodic ESS receive burst size
  * @tx_thr_num_pkt_prd: periodic ESS transmit packet count
  * @tx_max_burst_prd: max periodic ESS transmit burst size
+ * @tx_fifo_resize_max_num: max number of fifos allocated during txfifo resize
  * @hsphy_interface: "utmi" or "ulpi"
  * @connected: true when we're connected to a host, false otherwise
  * @delayed_status: true when gadget driver asks for delayed status

@@ -1037,6 +1038,7 @@ struct dwc3_scratchpad_array {
  *	1	- utmi_l1_suspend_n
  * @is_fpga: true when we are using the FPGA board
  * @pending_events: true when we have pending IRQs to be handled
+ * @do_fifo_resize: true when txfifo resizing is enabled for dwc3 endpoints
  * @pullups_connected: true when Run/Stop bit is set
  * @setup_packet_pending: true when there's a Setup Packet in FIFO. Workaround
  * @three_stage_setup: set if we perform a three phase setup

@@ -1079,6 +1081,11 @@ struct dwc3_scratchpad_array {
  * @dis_split_quirk: set to disable split boundary.
  * @imod_interval: set the interrupt moderation interval in 250ns
  *			increments or 0 to disable.
+ * @max_cfg_eps: current max number of IN eps used across all USB configs.
+ * @last_fifo_depth: last fifo depth used to determine next fifo ram start
+ *		     address.
+ * @num_ep_resized: carries the current number endpoints which have had its tx
+ *		    fifo resized.
  */
 struct dwc3 {
 	struct work_struct	drd_work;

@@ -1233,6 +1240,7 @@ struct dwc3 {
 	u8			rx_max_burst_prd;
 	u8			tx_thr_num_pkt_prd;
 	u8			tx_max_burst_prd;
+	u8			tx_fifo_resize_max_num;
 
 	const char		*hsphy_interface;
 

@@ -1246,6 +1254,7 @@ struct dwc3 {
 	unsigned		is_utmi_l1_suspend:1;
 	unsigned		is_fpga:1;
 	unsigned		pending_events:1;
+	unsigned		do_fifo_resize:1;
 	unsigned		pullups_connected:1;
 	unsigned		setup_packet_pending:1;
 	unsigned		three_stage_setup:1;

@@ -1281,6 +1290,10 @@ struct dwc3 {
 	unsigned		dis_split_quirk:1;
 
 	u16			imod_interval;
+
+	int			max_cfg_eps;
+	int			last_fifo_depth;
+	int			num_ep_resized;
 };
 
 #define INCRX_BURST_MODE 0

@@ -1512,6 +1525,7 @@ int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned int cmd,
 		struct dwc3_gadget_ep_cmd_params *params);
 int dwc3_send_gadget_generic_command(struct dwc3 *dwc, unsigned int cmd,
 		u32 param);
+void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc);
 #else
 static inline int dwc3_gadget_init(struct dwc3 *dwc)
 { return 0; }

@@ -1531,6 +1545,8 @@ static inline int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned int cmd,
 static inline int dwc3_send_gadget_generic_command(struct dwc3 *dwc,
 		int cmd, u32 param)
 { return 0; }
+static inline void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc)
+{ }
 #endif
 
 #if IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE)

drivers/usb/dwc3/ep0.c +2 -0

index 3cd2942..d28d085 100644
@@ -619,6 +619,8 @@ static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl)
 		return -EINVAL;
 
 	case USB_STATE_ADDRESS:
+		dwc3_gadget_clear_tx_fifos(dwc);
+
 		ret = dwc3_ep0_delegate_req(dwc, ctrl);
 		/* if the cfg matches and the cfg is non zero */
 		if (cfg && (!ret || (ret == USB_GADGET_DELAYED_STATUS))) {

drivers/usb/dwc3/gadget.c +9 -0

index af6d7f1..e56f1a6 100644
@@ -632,6 +632,187 @@ static void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force,
 		bool interrupt);
 
 /**
+ * dwc3_gadget_calc_tx_fifo_size - calculates the txfifo size value
+ * @dwc: pointer to the DWC3 context
+ * @nfifos: number of fifos to calculate for
+ *
+ * Calculates the size value based on the equation below:
+ *
+ * DWC3 revision 280A and prior:
+ * fifo_size = mult * (max_packet / mdwidth) + 1;
+ *

drivers/usb/dwc3/gadget.c static void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force, · line 651

Quoted 8 lines

drivers/usb/dwc3/gadget.c +8 -0

+ * DWC3 revision 290A and onwards:
+ * fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1
+ *
+ * The max packet size is set to 1024, as the txfifo requirements mainly apply
+ * to super speed USB use cases.  However, it is safe to overestimate the fifo
+ * allocations for other scenarios, i.e. high speed USB.
+ */
+static int dwc3_gadget_calc_tx_fifo_size(struct dwc3 *dwc, int mult)

drivers/usb/dwc3/gadget.c static void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force, · line 657

Quoted 6 lines

drivers/usb/dwc3/gadget.c +6 -0

+{
+	int max_packet = 1024;
+	int fifo_size;
+	int mdwidth;
+
+	mdwidth = dwc3_mdwidth(dwc);

drivers/usb/dwc3/gadget.c static void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force, · line 660

Quoted 3 lines

drivers/usb/dwc3/gadget.c +3 -0

+
+	/* MDWIDTH is represented in bits, we need it in bytes */
+	mdwidth >>= 3;

drivers/usb/dwc3/gadget.c static void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force, · line 665

Quoted 5 lines

drivers/usb/dwc3/gadget.c +5 -0

+
+	if (DWC3_VER_IS_PRIOR(DWC3, 290A))
+		fifo_size = mult * (max_packet / mdwidth) + 1;
+	else
+		fifo_size = mult * ((max_packet + mdwidth) / mdwidth) + 1;

Quoted 85 lines

drivers/usb/dwc3/gadget.c +84 -0

+	return fifo_size;
+}
+
+/**
+ * dwc3_gadget_clear_tx_fifo_size - Clears txfifo allocation
+ * @dwc: pointer to the DWC3 context
+ *
+ * Iterates through all the endpoint registers and clears the previous txfifo
+ * allocations.
+ */
+void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc)
+{
+	struct dwc3_ep *dep;
+	int fifo_depth;
+	int size;
+	int num;
+
+	if (!dwc->do_fifo_resize)
+		return;
+
+	/* Read ep0IN related TXFIFO size */
+	dep = dwc->eps[1];
+	size = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0));
+	if (DWC3_IP_IS(DWC3))
+		fifo_depth = DWC3_GTXFIFOSIZ_TXFDEP(size);
+	else
+		fifo_depth = DWC31_GTXFIFOSIZ_TXFDEP(size);
+
+	dwc->last_fifo_depth = fifo_depth;
+	/* Clear existing TXFIFO for all IN eps except ep0 */
+	for (num = 3; num < min_t(int, dwc->num_eps, DWC3_ENDPOINTS_NUM);
+	     num += 2) {
+		dep = dwc->eps[num];
+		/* Don't change TXFRAMNUM on usb31 version */
+		size = DWC3_IP_IS(DWC3) ? 0 :
+			dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(num >> 1)) &
+				   DWC31_GTXFIFOSIZ_TXFRAMNUM;
+
+		dwc3_writel(dwc->regs, DWC3_GTXFIFOSIZ(num >> 1), size);
+	}
+	dwc->num_ep_resized = 0;
+}
+
+/*
+ * dwc3_gadget_resize_tx_fifos - reallocate fifo spaces for current use-case
+ * @dwc: pointer to our context structure
+ *
+ * This function will a best effort FIFO allocation in order
+ * to improve FIFO usage and throughput, while still allowing
+ * us to enable as many endpoints as possible.
+ *
+ * Keep in mind that this operation will be highly dependent
+ * on the configured size for RAM1 - which contains TxFifo -,
+ * the amount of endpoints enabled on coreConsultant tool, and
+ * the width of the Master Bus.
+ *
+ * In general, FIFO depths are represented with the following equation:
+ *
+ * fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1
+ *
+ * In conjunction with dwc3_gadget_check_config(), this resizing logic will
+ * ensure that all endpoints will have enough internal memory for one max
+ * packet per endpoint.
+ */
+static int dwc3_gadget_resize_tx_fifos(struct dwc3_ep *dep)
+{
+	struct dwc3 *dwc = dep->dwc;
+	int fifo_0_start;
+	int ram1_depth;
+	int fifo_size;
+	int min_depth;
+	int num_in_ep;
+	int remaining;
+	int num_fifos = 1;
+	int fifo;
+	int tmp;
+
+	if (!dwc->do_fifo_resize)
+		return 0;
+
+	/* resize IN endpoints except ep0 */
+	if (!usb_endpoint_dir_in(dep->endpoint.desc) || dep->number <= 1)
+		return 0;
 
+

drivers/usb/dwc3/gadget.c static void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force, · line 759

Quoted 10 lines

drivers/usb/dwc3/gadget.c +10 -0

+	ram1_depth = DWC3_RAM1_DEPTH(dwc->hwparams.hwparams7);
+
+	if ((dep->endpoint.maxburst > 1 &&
+	     usb_endpoint_xfer_bulk(dep->endpoint.desc)) ||
+	    usb_endpoint_xfer_isoc(dep->endpoint.desc))
+		num_fifos = 3;
+
+	if (dep->endpoint.maxburst > 6 &&
+	    usb_endpoint_xfer_bulk(dep->endpoint.desc) && DWC3_IP_IS(DWC31))
+		num_fifos = dwc->tx_fifo_resize_max_num;

Why only bulk? Isoc should be at least equal or more than bulk. Also, make this applicable to DWC_usb32 also.

drivers/usb/dwc3/gadget.c static void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force, · line 766

Quoted 7 lines

drivers/usb/dwc3/gadget.c +7 -0

+
+	/* FIFO size for a single buffer */
+	fifo = dwc3_gadget_calc_tx_fifo_size(dwc, 1);
+
+	/* Calculate the number of remaining EPs w/o any FIFO */
+	num_in_ep = dwc->max_cfg_eps;
+	num_in_ep -= dwc->num_ep_resized;

Does this calculation account for multiple alt-setting interfaces?

drivers/usb/dwc3/gadget.c static void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force, · line 771

Quoted 5 lines

drivers/usb/dwc3/gadget.c +5 -0

+
+	/* Reserve at least one FIFO for the number of IN EPs */
+	min_depth = num_in_ep * (fifo + 1);
+	remaining = ram1_depth - min_depth - dwc->last_fifo_depth;
+	remaining = max_t(int, 0, remaining);

Add blank line

Quoted 31 lines

drivers/usb/dwc3/gadget.c +31 -0

+	/*
+	 * We've already reserved 1 FIFO per EP, so check what we can fit in
+	 * addition to it.  If there is not enough remaining space, allocate
+	 * all the remaining space to the EP.
+	 */
+	fifo_size = (num_fifos - 1) * fifo;
+	if (remaining < fifo_size)
+		fifo_size = remaining;
+
+	fifo_size += fifo;
+	/* Last increment according to the TX FIFO size equation */
+	fifo_size++;
+
+	/* Check if TXFIFOs start at non-zero addr */
+	tmp = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0));
+	fifo_0_start = DWC3_GTXFIFOSIZ_TXFSTADDR(tmp);
+
+	fifo_size |= (fifo_0_start + (dwc->last_fifo_depth << 16));
+	if (DWC3_IP_IS(DWC3))
+		dwc->last_fifo_depth += DWC3_GTXFIFOSIZ_TXFDEP(fifo_size);
+	else
+		dwc->last_fifo_depth += DWC31_GTXFIFOSIZ_TXFDEP(fifo_size);
+
+	/* Check fifo size allocation doesn't exceed available RAM size. */
+	if (dwc->last_fifo_depth >= ram1_depth) {
+		dev_err(dwc->dev, "Fifosize(%d) > RAM size(%d) %s depth:%d\n",
+			dwc->last_fifo_depth, ram1_depth,
+			dep->endpoint.name, fifo_size);
+		if (DWC3_IP_IS(DWC3))
+			fifo_size = DWC3_GTXFIFOSIZ_TXFDEP(fifo_size);
+		else

drivers/usb/dwc3/gadget.c static void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force, · line 810

Quoted 8 lines

drivers/usb/dwc3/gadget.c +8 -0

+			fifo_size = DWC31_GTXFIFOSIZ_TXFDEP(fifo_size);
+
+		dwc->last_fifo_depth -= fifo_size;
+		return -ENOMEM;
+	}
+
+	dwc3_writel(dwc->regs, DWC3_GTXFIFOSIZ(dep->number >> 1), fifo_size);
+	dwc->num_ep_resized++;

Quoted 64 lines

drivers/usb/dwc3/gadget.c +5 -0

+
+	return 0;
+}
+
+/**
  * __dwc3_gadget_ep_enable - initializes a hw endpoint
  * @dep: endpoint to be initialized

* @action: one of INIT, MODIFY or RESTORE

drivers/usb/dwc3/gadget.c +38 -0

@@ -648,6 +829,10 @@ static int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action)
 	int			ret;
 
 	if (!(dep->flags & DWC3_EP_ENABLED)) {
+		ret = dwc3_gadget_resize_tx_fifos(dep);
+		if (ret)
+			return ret;
+
 		ret = dwc3_gadget_start_config(dep);
 		if (ret)
 			return ret;

@@ -2498,6 +2683,7 @@ static int dwc3_gadget_stop(struct usb_gadget *g)
 
 	spin_lock_irqsave(&dwc->lock, flags);
 	dwc->gadget_driver	= NULL;
+	dwc->max_cfg_eps = 0;
 	spin_unlock_irqrestore(&dwc->lock, flags);
 
 	free_irq(dwc->irq_gadget, dwc->ev_buf);

@@ -2585,6 +2771,51 @@ static int dwc3_gadget_vbus_draw(struct usb_gadget *g, unsigned int mA)
 	return ret;
 }
 
+/**
+ * dwc3_gadget_check_config - ensure dwc3 can support the USB configuration
+ * @g: pointer to the USB gadget
+ *
+ * Used to record the maximum number of endpoints being used in a USB composite
+ * device. (across all configurations)  This is to be used in the calculation
+ * of the TXFIFO sizes when resizing internal memory for individual endpoints.
+ * It will help ensured that the resizing logic reserves enough space for at
+ * least one max packet.
+ */
+static int dwc3_gadget_check_config(struct usb_gadget *g)
+{
+	struct dwc3 *dwc = gadget_to_dwc(g);
+	struct usb_ep *ep;
+	int fifo_size = 0;
+	int ram1_depth;
+	int ep_num = 0;
+
+	if (!dwc->do_fifo_resize)
+		return 0;
+
+	list_for_each_entry(ep, &g->ep_list, ep_list) {
+		/* Only interested in the IN endpoints */
+		if (ep->claimed && (ep->address & USB_DIR_IN))
+			ep_num++;
+	}
+
+	if (ep_num <= dwc->max_cfg_eps)
+		return 0;
+
+	/* Update the max number of eps in the composition */
+	dwc->max_cfg_eps = ep_num;
+

drivers/usb/dwc3/gadget.c static int dwc3_gadget_vbus_draw(struct usb_gadget *g, unsigned int mA) · line 2814

Quoted 8 lines

drivers/usb/dwc3/gadget.c +8 -0

+	fifo_size = dwc3_gadget_calc_tx_fifo_size(dwc, dwc->max_cfg_eps);
+	/* Based on the equation, increment by one for every ep */
+	fifo_size += dwc->max_cfg_eps;
+
+	/* Check if we can fit a single fifo per endpoint */
+	ram1_depth = DWC3_RAM1_DEPTH(dwc->hwparams.hwparams7);
+	if (fifo_size > ram1_depth)
+		return -ENOMEM;

Quoted 14 lines

drivers/usb/dwc3/gadget.c +5 -0

+
+	return 0;
+}
+
 static const struct usb_gadget_ops dwc3_gadget_ops = {
 	.get_frame		= dwc3_gadget_get_frame,
 	.wakeup			= dwc3_gadget_wakeup,

@@ -2596,6 +2827,7 @@ static const struct usb_gadget_ops dwc3_gadget_ops = {
 	.udc_set_ssp_rate	= dwc3_gadget_set_ssp_rate,
 	.get_config_params	= dwc3_gadget_config_params,
 	.vbus_draw		= dwc3_gadget_vbus_draw,
+	.check_config		= dwc3_gadget_check_config,
 };
 

drivers/usb/dwc3/gadget.c static const struct usb_gadget_ops dwc3_gadget_ops = { · line 2833

Quoted 2 lines

drivers/usb/dwc3/gadget.c +0 -0

 /* -------------------------------------------------------------------------- */