config: Add 'update_bootimg' command to update flash.bin on Phytec's imx8mm
PATCH v2 1/1 config: Add 'update_bootimg' command to update flash.bin on Phytec's imx8mm
This command allows easy update on SD card or eMMC of the flash.bin generated (with binman) during u-boot build.
---
Changes for v2:
- Remove 'update_mmc_part' variable
- Change path for hostname
- Use full version of dhcp command (${loadaddr} added)
--- include/configs/phycore_imx8mm.h | 10 ++++++++++ 1 file changed, 10 insertions(+)
include/configs/phycore_imx8mm.h +10 -0
@@ -29,6 +29,16 @@ "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \"mmcpart=1\0" \"mmcroot=2\0" \ +"update_offset=0x42\0" \ +"update_filename=flash.bin\0" \ +"hostname=/srv/tftp/\0" \ +"update_bootimg=" \ +"mmc dev ${mmcdev} ; " \ +"if dhcp ${loadaddr} ${hostname}/${update_filename} ; then " \ +"setexpr fw_sz ${filesize} / 0x200 ; " /* SD block size */ \ +"setexpr fw_sz ${fw_sz} + 1 ; " \ +"mmc write ${loadaddr} ${update_offset} ${fw_sz} ; " \ +"fi\0" \"mmcautodetect=yes\0" \"mmcargs=setenv bootargs console=${console} " \"root=/dev/mmcblk${mmcdev}p${mmcroot} rootwait rw\0" \
Signature · 1 line
2.39.2
Fabio Estevam
reviewerHi Lukasz,
include/configs/phycore_imx8mm.h
Quoted 8 lines · Lukasz Majewski
include/configs/phycore_imx8mm.h +8
-0+"update_offset=0x42\0" \ +"update_filename=flash.bin\0" \ +"hostname=/srv/tftp/\0" \ +"update_bootimg=" \ +"mmc dev ${mmcdev} ; " \ +"if dhcp ${loadaddr} ${hostname}/${update_filename} ; then " \ +"setexpr fw_sz ${filesize} / 0x200 ; " /* SD block size */ \ +"setexpr fw_sz ${fw_sz} + 1 ; "
As Benjamin pointed out earlier this increment by one is not necessary.
All other i.MX8M docs don't have this increment.
Hi Fabio,
Quoted 16 lines
Hi Lukasz,
Quoted 11 lines · Lukasz Majewski
include/configs/phycore_imx8mm.h +6
-0+"update_offset=0x42\0" \ +"update_filename=flash.bin\0" \ +"hostname=/srv/tftp/\0" \ +"update_bootimg=" \ +"mmc dev ${mmcdev} ; " \ + "if dhcp ${loadaddr} ${hostname}/${update_filename}; then " \
+ "setexprfw_sz${filesize} /0x200; " /* SD block
size */ \
+ "setexprfw_sz${fw_sz} + 1 ; "
Quoted 4 lines
As Benjamin pointed out earlier this increment by one is not necessary.
All other i.MX8M docs don't have this increment.
So apparently the BSP build scripts in OE/Yocto take always care to have 0x200 aligned binaries (imx-boot and flash.bin).
OK, I will remove it.
Best regards,
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Erika Unter
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: [email protected]