Skip to contentSkip to conversation

Preliminary support for Raspberry Pi 3 with symlink

PATCH New Ubaldo Porcheddu 5 participants 14 messages Apr 23, 2016 – Apr 26, 2016 Broadcom BCM2711/BCM2835 Arm architecture

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 Preliminary support for Raspberry Pi 3 with symlink

---
 board/raspberrypi/genimage-raspberrypi3.cfg | 30 ++++++++++++++++++++++++
 board/raspberrypi/readme.txt                | 10 ++++++--
 board/raspberrypi3                          |  1 +
 configs/raspberrypi3_defconfig              | 36 +++++++++++++++++++++++++++++
 4 files changed, 75 insertions(+), 2 deletions(-)
 create mode 100644 board/raspberrypi/genimage-raspberrypi3.cfg
 create mode 120000 board/raspberrypi3
 create mode 100644 configs/raspberrypi3_defconfig
board/raspberrypi/genimage-raspberrypi3.cfg new file +30 -0
new file mode 100644
index 0000000..7ba89c5
@@ -0,0 +1,30 @@
+image boot.vfat {
+  vfat {
+    files = {
+      "bcm2710-rpi-3-b.dtb",
+      "rpi-firmware/bootcode.bin",
+      "rpi-firmware/cmdline.txt",
+      "rpi-firmware/config.txt",
+      "rpi-firmware/fixup.dat",
+      "rpi-firmware/start.elf",
+      "kernel-marked/zImage"
+    }
+  }
+  size = 32M
+}
+
+image sdcard.img {
+  hdimage {
+  }
+
+  partition boot {
+    partition-type = 0xC
+    bootable = "true"
+    image = "boot.vfat"
+  }
+
+  partition rootfs {
+    partition-type = 0x83
+    image = "rootfs.ext4"
+  }
+}
board/raspberrypi/readme.txt +8 -2
index 896be2d..a170f8f 100644
@@ -6,7 +6,8 @@ Intro
 These instructions apply to all models of the Raspberry Pi:
   - the original models A and B,
   - the "enhanced" models A+ and B+,
-  - the model B2 (aka Raspberry Pi 2).
+  - the model B2 (aka Raspberry Pi 2)
+  - the model B3 (aka Raspberry Pi 3).
 
 How to build it
 ===============
@@ -21,10 +22,14 @@ For models A, B, A+ or B+:
 
   $ make raspberrypi_defconfig
 
-And for model 2 B:
+For model 2 B:
 
   $ make raspberrypi2_defconfig
 
+For model 3 B:
+
+  $ make raspberrypi3_defconfig
+
 Build the rootfs
 ----------------
 
@@ -46,6 +51,7 @@ After building, you should obtain this tree:
     +-- bcm2708-rpi-b.dtb           [1]
     +-- bcm2708-rpi-b-plus.dtb      [1]
     +-- bcm2709-rpi-2-b.dtb         [1]
+    +-- bcm2710-rpi-3-b.dtb         [1]
     +-- boot.vfat
     +-- kernel-marked/zImage        [2]
     +-- rootfs.ext4
board/raspberrypi3 new file +1 -0
new file mode 120000
index 0000000..fcdafc8
@@ -0,0 +1 @@
+raspberrypi
\ No newline at end of file
configs/raspberrypi3_defconfig new file +36 -0
new file mode 100644
index 0000000..80ce908
@@ -0,0 +1,36 @@
+BR2_arm=y
+BR2_cortex_a7=y
+BR2_ARM_EABIHF=y
+BR2_ARM_FPU_NEON_VFPV4=y
+
+BR2_TOOLCHAIN_BUILDROOT_CXX=y
+
+BR2_SYSTEM_DHCP="eth0"
+
+# Linux headers same as kernel, a 4.1 series
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+
+BR2_LINUX_KERNEL=y
+BR2_LINUX_KERNEL_CUSTOM_GIT=y
+BR2_LINUX_KERNEL_CUSTOM_REPO_URL="https://github.com/raspberrypi/linux.git"
+BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="20fe468af4bb40fec0f81753da4b20a8bfc259c9"
+BR2_LINUX_KERNEL_DEFCONFIG="bcm2709"
+
+# Build the DTB from the kernel sources
+BR2_LINUX_KERNEL_DTS_SUPPORT=y
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="bcm2710-rpi-3-b"
+
+BR2_PACKAGE_RPI_FIRMWARE=y
+# BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTB_OVERLAYS is not set
+
+# Required tools to create the SD image
+BR2_PACKAGE_HOST_DOSFSTOOLS=y
+BR2_PACKAGE_HOST_GENIMAGE=y
+BR2_PACKAGE_HOST_MTOOLS=y
+
+# Filesystem / image
+BR2_TARGET_ROOTFS_EXT2=y
+BR2_TARGET_ROOTFS_EXT2_4=y
+# BR2_TARGET_ROOTFS_TAR is not set
+BR2_ROOTFS_POST_BUILD_SCRIPT="board/raspberrypi3/post-build.sh"
+BR2_ROOTFS_POST_IMAGE_SCRIPT="board/raspberrypi3/post-image.sh"
Signature · 1 line
1.9.1
#1 lore raw

PATCH 1/1 Preliminary support for Raspberry Pi 3 with symlink

Quoted 3 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Ubaldo" == Ubaldo Porcheddu <[email protected]> writes:

Committed after expanding the commit message, thanks.

I've also committed a change to sync the kernel version with what is used for rpi1/2 (E.G. the rpi-4.4.y branch). Care to verify that everything works correctly after that?

What about the serial console? The rpi3 afaik uses ttyS0 instead of ttyAMA0 for the (default) serial console. Do we need to adjust cmdline.txt for the rpi?

I see notes about newer rpi-firmware versions fixing up ttyAMA0 -> ttyS0 when running on a rpi3, so perhaps it isn't needed?

https://github.com/RPi-Distro/repo/issues/22

Signature · 1 line
Bye, Peter Korsgaard
#2 lore raw

PATCH 1/1 Preliminary support for Raspberry Pi 3 with symlink

Hi Peter,

Il 2016-04-25 13:07 Peter Korsgaard ha scritto:

Quoted 9 lines
Quoted 3 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Ubaldo" == Ubaldo Porcheddu <[email protected]> writes:

Committed after expanding the commit message, thanks.

I've also committed a change to sync the kernel version with what is used for rpi1/2 (E.G. the rpi-4.4.y branch). Care to verify that everything works correctly after that?

I just tested the new kernel version but it doesn't give me the login prompt, the kernel seems to be booting fine as it can recognize my keyboard but it doesn't accept any input.

Quoted 9 lines

What about the serial console? The rpi3 afaik uses ttyS0 instead of ttyAMA0 for the (default) serial console. Do we need to adjust cmdline.txt for the rpi?

I see notes about newer rpi-firmware versions fixing up ttyAMA0 -> ttyS0
when running on a rpi3, so perhaps it isn't needed?

https://github.com/RPi-Distro/repo/issues/22

I don't have a serial console cable to test with at the moment, but I can see from the kernel log on screen a message like:

console [ttyS0] enabled

#3 lore raw

PATCH 1/1 Preliminary support for Raspberry Pi 3 with symlink

Quoted 10 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Ubaldo" == Ubaldo Porcheddu <[email protected]> writes:

Hi Peter,
Il 2016-04-25 13:07 Peter Korsgaard ha scritto:

Quoted 6 lines
Quoted 3 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Ubaldo" == Ubaldo Porcheddu <[email protected]> writes:

Committed after expanding the commit message, thanks.

Quoted 7 lines
Quoted 3 lines

I've also committed a change to sync the kernel version with what is used for rpi1/2 (E.G. the rpi-4.4.y branch). Care to verify that everything works correctly after that?

I just tested the new kernel version but it doesn't give me the login prompt, the kernel seems to be booting fine as it can recognize my keyboard but it doesn't accept any input.

Hmm, odd. I do have a rpi1 at home. I'll try the 4.4 kernel on that one.

So do I understand you correctly that you do see the kernel messages on the HDMI output but don't get a login prompt / nothing happens when you type on your USB keyboard.

Quoted 8 lines
Quoted 8 lines

What about the serial console? The rpi3 afaik uses ttyS0 instead of ttyAMA0 for the (default) serial console. Do we need to adjust cmdline.txt for the rpi?

I see notes about newer rpi-firmware versions fixing up ttyAMA0 -> ttyS0
when running on a rpi3, so perhaps it isn't needed?

Quoted 6 lines
Quoted 1 line

https://github.com/RPi-Distro/repo/issues/22

I don't have a serial console cable to test with at the moment, but I can see from the kernel log on screen a message like:

console [ttyS0] enabled

Ok, sounds like it does the right thing then - Thanks!

Signature · 2 lines
Venlig hilsen,
Peter Korsgaard 
#4 lore raw

PATCH 1/1 Preliminary support for Raspberry Pi 3 with symlink

Il 2016-04-25 15:14 Peter Korsgaard ha scritto:

Quoted 20 lines
Quoted 11 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Ubaldo" == Ubaldo Porcheddu <[email protected]> writes:

Hi Peter,
Il 2016-04-25 13:07 Peter Korsgaard ha scritto:

Quoted 7 lines
Quoted 3 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Ubaldo" == Ubaldo Porcheddu <[email protected]> writes:

Committed after expanding the commit message, thanks.

I've also committed a change to sync the kernel version with what

is

Quoted 4 lines
Quoted 2 lines

used for rpi1/2 (E.G. the rpi-4.4.y branch). Care to verify that everything works correctly after that?

I just tested the new kernel version but it doesn't give me the

login

Quoted 2 lines

prompt, the kernel seems to be booting fine as it can recognize my keyboard but it doesn't accept any input.

Quoted 6 lines

Hmm, odd. I do have a rpi1 at home. I'll try the 4.4 kernel on that one.

So do I understand you correctly that you do see the kernel messages on the HDMI output but don't get a login prompt / nothing happens when you type on your USB keyboard.

yes this is actually what is happening.

#5 lore raw

PATCH 1/1 Preliminary support for Raspberry Pi 3 with symlink

In reply to Peter Korsgaard
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Peter" == Peter Korsgaard <[email protected]> writes:

Hi,

Quoted 5 lines
Quoted 3 lines

I just tested the new kernel version but it doesn't give me the login prompt, the kernel seems to be booting fine as it can recognize my keyboard but it doesn't accept any input.

Hmm, odd. I do have a rpi1 at home. I'll try the 4.4 kernel on that one.

On the rpi1 everything works correctly. /dev/console refers to the serial port and I can login both on HDMI and serial - So I guess the problem must be specific to the rpi3.

Signature · 1 line
Bye, Peter Korsgaard
#6 lore raw

PATCH 1/1 Preliminary support for Raspberry Pi 3 with symlink

In reply to Ubaldo Porcheddu
Quoted 9 lines · On Mon, 25 Apr 2016 15:06:54 +0100 Ubaldo Porcheddu <[email protected]> wrote:

Hi Peter,

Il 2016-04-25 13:07 Peter Korsgaard ha scritto:

Quoted 6 lines
Quoted 3 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Ubaldo" == Ubaldo Porcheddu <[email protected]> writes:

Committed after expanding the commit message, thanks.

Quoted 8 lines
Quoted 3 lines

I've also committed a change to sync the kernel version with what is used for rpi1/2 (E.G. the rpi-4.4.y branch). Care to verify that everything works correctly after that?

I just tested the new kernel version but it doesn't give me the login prompt, the kernel seems to be booting fine as it can recognize my keyboard but it doesn't accept any input.

I had something similar, removed the 'console=ttyAMA0...' from the cmdline.txt file, and it booted through. Mine was not able to recognize my keyboard, but with dropbear and an extra user I was able to login.

Quoted 9 lines
Quoted 9 lines

What about the serial console? The rpi3 afaik uses ttyS0 instead of ttyAMA0 for the (default) serial console. Do we need to adjust cmdline.txt for the rpi?

I see notes about newer rpi-firmware versions fixing up ttyAMA0 -> ttyS0
when running on a rpi3, so perhaps it isn't needed?

Quoted 6 lines
Quoted 1 line

https://github.com/RPi-Distro/repo/issues/22

I don't have a serial console cable to test with at the moment, but I can see from the kernel log on screen a message like:

console [ttyS0] enabled

I see:

    3f215040.uart: ttyS0 at MMIO 0x3f215040 (irq = 59, base_baud =
    50000000) is a 16550

Please note that there is a line about tyAMA0 in the kernel boot logs as well:

    3f201000.uart: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0)
    is a PL011 rev2

Regards,
Ben.

Quoted 4 lines

_______________________________________________
buildroot mailing list
buildroot at busybox.net
http://lists.busybox.net/mailman/listinfo/buildroot

-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 473 bytes
Desc: OpenPGP digital signature
URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20160425/9fdc2a59/attachment.asc>

#7 lore raw

PATCH 1/1 Preliminary support for Raspberry Pi 3 with symlink

Hi Ben,

Il 2016-04-25 15:16 Beno?t Allard ha scritto:

Quoted 16 lines
Quoted 13 lines · On Mon, 25 Apr 2016 15:06:54 +0100 Ubaldo Porcheddu <[email protected]> wrote:

Hi Peter,

Il 2016-04-25 13:07 Peter Korsgaard ha scritto:

Quoted 9 lines
Quoted 3 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Ubaldo" == Ubaldo Porcheddu <[email protected]> writes:

Committed after expanding the commit message, thanks.

I've also committed a change to sync the kernel version with what is used for rpi1/2 (E.G. the rpi-4.4.y branch). Care to verify that everything works correctly after that?

Quoted 8 lines
Quoted 4 lines

I just tested the new kernel version but it doesn't give me the login prompt, the kernel seems to be booting fine as it can recognize my keyboard but it doesn't accept any input.

I had something similar, removed the 'console=ttyAMA0...' from the cmdline.txt file, and it booted through. Mine was not able to recognize my keyboard, but with dropbear and an extra user I was able to login.

after removing the extra console declaration I can also get the login, my keyboard get recognized by the kernel but it doesn't work properly, seems to be adding extra characters after any key press.

#8 lore raw

PATCH 1/1 Preliminary support for Raspberry Pi 3 with symlink

Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Ubaldo" == Ubaldo Porcheddu <[email protected]> writes:

Hi,

Quoted 5 lines
Quoted 5 lines
Quoted 4 lines

I just tested the new kernel version but it doesn't give me the login prompt, the kernel seems to be booting fine as it can recognize my keyboard but it doesn't accept any input.

Quoted 7 lines
Quoted 3 lines

I had something similar, removed the 'console=ttyAMA0...' from the cmdline.txt file, and it booted through. Mine was not able to recognize my keyboard, but with dropbear and an extra user I was able to login.

after removing the extra console declaration I can also get the login, my keyboard get recognized by the kernel but it doesn't work properly, seems to be adding extra characters after any key press.

Funky. Removing console=ttyAMA0 (or console=ttyS0) would mean that tty1 becomes /dev/console, so we end up having two gettys running on tty1 which could explain the double characters.

I'm not sure why it doesn't work with console= pointing at the serial port. Luca, you added the serial console handling, any idea what might be going wrong?

Signature · 2 lines
Venlig hilsen,
Peter Korsgaard 
#9 lore raw

PATCH 1/1 Preliminary support for Raspberry Pi 3 with symlink

Hi,

Il 2016-04-25 15:40 Peter Korsgaard ha scritto:

Quoted 22 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Ubaldo" == Ubaldo Porcheddu <[email protected]> writes:

Hi,

Quoted 8 lines
Quoted 8 lines
Quoted 5 lines

I just tested the new kernel version but it doesn't give me the login
prompt, the kernel seems to be booting fine as it can recognize my keyboard but it doesn't accept any input.

I had something similar, removed the 'console=ttyAMA0...' from the cmdline.txt file, and it booted through. Mine was not able to

recognize

Quoted 1 line
Quoted 1 line

my keyboard, but with dropbear and an extra user I was able to

login.

Quoted 1 line

after removing the extra console declaration I can also get the

login,

Quoted 1 line

my keyboard get recognized by the kernel but it doesn't work

properly,

Quoted 1 line

seems to be adding extra characters after any key press.

Quoted 7 lines

Funky. Removing console=ttyAMA0 (or console=ttyS0) would mean that tty1 becomes /dev/console, so we end up having two gettys running on tty1 which could explain the double characters.

I'm not sure why it doesn't work with console= pointing at the serial port. Luca, you added the serial console handling, any idea what might be going wrong?

You are right about the double getty, indeed if I set console=tty2 I end up with a working getty/login on tty1 and tty2 and error messages on tty2.

Maybe the problem is in /etc/inittab using "console" in place of ttyS0?

#10 lore raw

PATCH 1/1 Preliminary support for Raspberry Pi 3 with symlink

In reply to Peter Korsgaard

Peter, Ubaldo,

Quoted 17 lines · Peter Korsgaard
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Ubaldo" == Ubaldo Porcheddu <[email protected]> writes:

Hi,

Quoted 5 lines
Quoted 5 lines
Quoted 4 lines

I just tested the new kernel version but it doesn't give me the login prompt, the kernel seems to be booting fine as it can recognize my keyboard but it doesn't accept any input.

Quoted 7 lines
Quoted 3 lines

I had something similar, removed the 'console=ttyAMA0...' from the cmdline.txt file, and it booted through. Mine was not able to recognize my keyboard, but with dropbear and an extra user I was able to login.

after removing the extra console declaration I can also get the login, my keyboard get recognized by the kernel but it doesn't work properly, seems to be adding extra characters after any key press.

Quoted 7 lines

Funky. Removing console=ttyAMA0 (or console=ttyS0) would mean that tty1 becomes /dev/console, so we end up having two gettys running on tty1 which could explain the double characters.

I'm not sure why it doesn't work with console= pointing at the serial port. Luca, you added the serial console handling, any idea what might be going wrong?

At first sight, no. But I experienced a similar issue while I was testing my patch [0].

I was able to login on tty1 with a USB keyboard, but typing a few characters such as "ls<ENTER>" just after login would do weird things like logging me out. This was using a super-cheap keyboard I had never used before. I retried with a trusted one, and it was working just fine. This got me clueless, so I triple-checked, and the problem was always happening with the cheap keyboard, never with the trusted one.

I thought the cheap keyboard must be broken and "archived" it.

I would be surprised if you could solve your issues by changing keyboard, but it's worth giving it a try...

[0]
https://git.buildroot.net/buildroot/commit/?id=20878a1017e2bf7eb8c5f870dc6d2641493cb0f9

Signature · 1 line
Luca
#11 lore raw

PATCH 1/1 Preliminary support for Raspberry Pi 3 with symlink

In reply to Ubaldo Porcheddu

Hello Ubaldo,

(and sorry from dropping you from CC, your e-mail address seems not to be reachable from gmx.net)

Quoted 9 lines · Ubaldo Porcheddu

Hi Peter,

Il 2016-04-25 13:07 Peter Korsgaard ha scritto:

Quoted 6 lines
Quoted 3 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Ubaldo" == Ubaldo Porcheddu <[email protected]> writes:

Committed after expanding the commit message, thanks.

Quoted 8 lines
Quoted 3 lines

I've also committed a change to sync the kernel version with what is used for rpi1/2 (E.G. the rpi-4.4.y branch). Care to verify that everything works correctly after that?

I just tested the new kernel version but it doesn't give me the login prompt, the kernel seems to be booting fine as it can recognize my keyboard but it doesn't accept any input.

Same here on RPi3, but with the suggested fix from Oscar Gomez Fuente [1], adding 'dtoverlay=pi3-disable-bt' to config.txt I get working boot messages and login on HDMI and serial console...

Regards,
Peter

[1] http://lists.busybox.net/pipermail/buildroot/2016-April/159295.html

Quoted 19 lines
Quoted 10 lines

What about the serial console? The rpi3 afaik uses ttyS0 instead of ttyAMA0 for the (default) serial console. Do we need to adjust cmdline.txt for the rpi?

I see notes about newer rpi-firmware versions fixing up ttyAMA0 -> ttyS0
when running on a rpi3, so perhaps it isn't needed?

https://github.com/RPi-Distro/repo/issues/22

I don't have a serial console cable to test with at the moment, but I can see from the kernel log on screen a message like:

console [ttyS0] enabled
_______________________________________________
buildroot mailing list
buildroot at busybox.net
http://lists.busybox.net/mailman/listinfo/buildroot

#12 lore raw

PATCH 1/1 Preliminary support for Raspberry Pi 3 with symlink

Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Peter" == Peter Seiderer <[email protected]> writes:

Hi,

Quoted 3 lines

Same here on RPi3, but with the suggested fix from Oscar Gomez Fuente [1], adding 'dtoverlay=pi3-disable-bt' to config.txt I get working boot messages and login on HDMI and serial console...

Just to confirm, neither serial or HDMI works without the dtoverlay line?

I see various references to a clocking issue with the "new" serial port, perhaps that is related?

Signature · 2 lines
Venlig hilsen,
Peter Korsgaard 
#13 lore raw

PATCH 1/1 Preliminary support for Raspberry Pi 3 with symlink

Hello Peter,

Quoted 10 lines · Peter Korsgaard
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Peter" == Peter Seiderer <[email protected]> writes:

Hi,

Quoted 3 lines

Same here on RPi3, but with the suggested fix from Oscar Gomez Fuente [1], adding 'dtoverlay=pi3-disable-bt' to config.txt I get working boot messages and login on HDMI and serial console...

Just to confirm, neither serial or HDMI works without the dtoverlay line?

Without the overlay I get boot messages on HDMI, but no login, last messages are from USB keyboard/mouse and I can get more messages removing/adding keyboard/mouse...., no messages on serial console (but 'ttyS0: 29 input overrun(s) message on HDMI output)

From linux-3de232825c9ba5989522b8691eb6ac5df6619458/arch/arm/boot/dts/overlays/pi3-disable-bt-overlay.dts:

Disable Bluetooth and restore UART0/ttyAMA0 over GPIOs 14 & 15.

So I think the overlay changes the pin muxing (and the orignal config seems to break the console, maybe flow control deadlock with the bluetooth chip?)...

Quoted 4 lines

I see various references to a clocking issue with the "new" serial port, perhaps that is related?

This was with old kernel/firmware but adding 'core_freq=250' to config.txt fixed it...

Regads,
Peter