U-Boot atheros PHY support and cubox ethernet
Subsystems (4)
Hey all,
In commit 4346df3392c0 ("phy: atheros: Make RGMII Tx delays actually configurable for AR8035") we brought in changes to get in to line with upstream linux kernel support for this PHY and in turn deal with more "driver was wrong, DT was wrong too" changes. Now the problem I have is that ethernet on my Hummingboard doesn't work AND as far as I can tell, the DTB is correct and saying phy-mode = "rgmii-id" now not "rgmii". It also looks to match what's in v5.7 for the kernel. What do I need to do here next? Thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200616/b78d3c65/attachment.sig>
Hi Tom,
Quoted 12 lines · Tom Rini
Hey all,
In commit
4346df3392c0("phy: atheros: Make RGMII Tx delays actually configurable for AR8035") we brought in changes to get in to line with upstream linux kernel support for this PHY and in turn deal with more "driver was wrong, DT was wrong too" changes. Now the problem I have is that ethernet on my Hummingboard doesn't work AND as far as I can tell, the DTB is correct and saying phy-mode = "rgmii-id" now not "rgmii". It also looks to match what's in v5.7 for the kernel. What do I need to do here next? Thanks!
Quoted 2 lines
--
Tom
Reverting 4346df3392c0 makes your interface work?
What is the DTS path that your hummingboard uses?
Thanks,
-Vladimir
Quoted 15 lines · Vladimir Oltean
Hi Tom,
Quoted 12 lines · Tom Rini
Hey all,
In commit
4346df3392c0("phy: atheros: Make RGMII Tx delays actually configurable for AR8035") we brought in changes to get in to line with upstream linux kernel support for this PHY and in turn deal with more "driver was wrong, DT was wrong too" changes. Now the problem I have is that ethernet on my Hummingboard doesn't work AND as far as I can tell, the DTB is correct and saying phy-mode = "rgmii-id" now not "rgmii". It also looks to match what's in v5.7 for the kernel. What do I need to do here next? Thanks!
Quoted 4 lines
Quoted 2 lines
--
TomReverting
4346df3392c0makes your interface work?
Yup.
Quoted 1 line
What is the DTS path that your hummingboard uses?
Good question. Per board/solidrun/mx6cuboxi/mx6cuboxi.c:
/*
* This is not a perfect match. Avoid dependency on the DM GPIO driver
* needed
* for accurate board detection. Hummingboard2 DT is good enough for
* U-Boot on
* all Hummingboard/Cubox-i platforms.
*/
so arch/arm/dts/imx6dl-hummingboard2-emmc-som-v15.dts is the base. But the board really is the original hummingboard platform. Thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200616/74e155de/attachment.sig>
Quoted 37 lines · Tom Rini
Quoted 15 lines · Vladimir Oltean
Hi Tom,
Quoted 12 lines · Tom Rini
Hey all,
In commit
4346df3392c0("phy: atheros: Make RGMII Tx delays actually configurable for AR8035") we brought in changes to get in to line with upstream linux kernel support for this PHY and in turn deal with more "driver was wrong, DT was wrong too" changes. Now the problem I have is that ethernet on my Hummingboard doesn't work AND as far as I can tell, the DTB is correct and saying phy-mode = "rgmii-id" now not "rgmii". It also looks to match what's in v5.7 for the kernel. What do I need to do here next? Thanks!Quoted 4 lines
Quoted 2 lines
--
TomReverting
4346df3392c0makes your interface work?Yup.
Quoted 1 line
What is the DTS path that your hummingboard uses?
Good question. Per
board/solidrun/mx6cuboxi/mx6cuboxi.c:
/*
* This is not a perfect match. Avoid dependency on the DM GPIO driver
* needed
* for accurate board detection. Hummingboard2 DT is good enough for
* U-Boot on
* all Hummingboard/Cubox-i platforms.
*/
soarch/arm/dts/imx6dl-hummingboard2-emmc-som-v15.dtsis the base. But the board really is the original hummingboard platform. Thanks!
Quoted 2 lines
--
Tom
Does it work if you say PHY_INTERFACE_MODE_RGMII_ID here?
https://gitlab.denx.de/u-boot/u-boot/-/blob/master/drivers/net/fec_mxc.c#L1232
-Vladimir
Quoted 38 lines · Vladimir Oltean
Quoted 37 lines · Tom Rini
Quoted 15 lines · Vladimir Oltean
Hi Tom,
Quoted 12 lines · Tom Rini
Hey all,
In commit
4346df3392c0("phy: atheros: Make RGMII Tx delays actually configurable for AR8035") we brought in changes to get in to line with upstream linux kernel support for this PHY and in turn deal with more "driver was wrong, DT was wrong too" changes. Now the problem I have is that ethernet on my Hummingboard doesn't work AND as far as I can tell, the DTB is correct and saying phy-mode = "rgmii-id" now not "rgmii". It also looks to match what's in v5.7 for the kernel. What do I need to do here next? Thanks!Quoted 4 lines
Quoted 2 lines
--
TomReverting
4346df3392c0makes your interface work?Yup.
Quoted 1 line
What is the DTS path that your hummingboard uses?
Good question. Per
board/solidrun/mx6cuboxi/mx6cuboxi.c:
/*
* This is not a perfect match. Avoid dependency on the DM GPIO driver
* needed
* for accurate board detection. Hummingboard2 DT is good enough for
* U-Boot on
* all Hummingboard/Cubox-i platforms.
*/
soarch/arm/dts/imx6dl-hummingboard2-emmc-som-v15.dtsis the base. But the board really is the original hummingboard platform. Thanks!
Quoted 5 lines
Quoted 2 lines
--
TomDoes it work if you say
PHY_INTERFACE_MODE_RGMII_IDhere?
https://gitlab.denx.de/u-boot/u-boot/-/blob/master/drivers/net/fec_mxc.c#L1232
No change. And to be clear, I bisect'd the issue down and at that commit, reverting it fixes ethernet. It doesn't revert cleanly (nor obviously to me) on master.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200616/9ce62576/attachment.sig>
Quoted 46 lines · Tom Rini
Quoted 38 lines · Vladimir Oltean
Quoted 37 lines · Tom Rini
Quoted 15 lines · Vladimir Oltean
Hi Tom,
Quoted 12 lines · Tom Rini
Hey all,
In commit
4346df3392c0("phy: atheros: Make RGMII Tx delays actually configurable for AR8035") we brought in changes to get in to line with upstream linux kernel support for this PHY and in turn deal with more "driver was wrong, DT was wrong too" changes. Now the problem I have is that ethernet on my Hummingboard doesn't work AND as far as I can tell, the DTB is correct and saying phy-mode = "rgmii-id" now not "rgmii". It also looks to match what's in v5.7 for the kernel. What do I need to do here next? Thanks!Quoted 4 lines
Quoted 2 lines
--
TomReverting
4346df3392c0makes your interface work?Yup.
Quoted 1 line
What is the DTS path that your hummingboard uses?
Good question. Per
board/solidrun/mx6cuboxi/mx6cuboxi.c:
/*
* This is not a perfect match. Avoid dependency on the DM GPIO driver
* needed
* for accurate board detection. Hummingboard2 DT is good enough for
* U-Boot on
* all Hummingboard/Cubox-i platforms.
*/
soarch/arm/dts/imx6dl-hummingboard2-emmc-som-v15.dtsis the base. But the board really is the original hummingboard platform. Thanks!Quoted 5 lines
Quoted 2 lines
--
TomDoes it work if you say
PHY_INTERFACE_MODE_RGMII_IDhere?
https://gitlab.denx.de/u-boot/u-boot/-/blob/master/drivers/net/fec_mxc.c#L1232
Quoted 6 lines
No change. And to be clear, I bisect'd the issue down and at that commit, reverting it fixes ethernet. It doesn't revert cleanly (nor obviously to me) on master.
--
Tom
On master, the revert would look like this:
drivers/net/phy/atheros.c +5 -0
@@ -124,6 +124,7 @@ static int ar8021_config(struct phy_device *phydev)static int ar803x_delay_config (struct phy_device *phydev) { +int regval;int ret; if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID ||
@@ -138,6 +139,10 @@ static int ar803x_delay_config(struct phy_device *phydev)else ret =ar803x_enable_rx_delay (phydev, false); +phy_write (phydev,MDIO_DEVAD_NONE ,0x1d ,0x05 ); + regval =phy_read (phydev,MDIO_DEVAD_NONE ,0x1e ); +phy_write (phydev,MDIO_DEVAD_NONE ,0x1e , (regval|0x0100 )); +return ret; }
The next thing to check is to print the value of phydev->interface there. 7 is PHY_INTERFACE_MODE_RGMII,
8 is PHY_INTERFACE_MODE_RGMII_ID,
9 is PHY_INTERFACE_MODE_RGMII_RXID,
10 is PHY_INTERFACE_MODE_RGMII_TXID,
You want it to be 8.
Thanks,
-Vladimir
Quoted 69 lines · Vladimir Oltean
Quoted 46 lines · Tom Rini
Quoted 38 lines · Vladimir Oltean
Quoted 37 lines · Tom Rini
Quoted 15 lines · Vladimir Oltean
Hi Tom,
Quoted 12 lines · Tom Rini
Hey all,
In commit
4346df3392c0("phy: atheros: Make RGMII Tx delays actually configurable for AR8035") we brought in changes to get in to line with upstream linux kernel support for this PHY and in turn deal with more "driver was wrong, DT was wrong too" changes. Now the problem I have is that ethernet on my Hummingboard doesn't work AND as far as I can tell, the DTB is correct and saying phy-mode = "rgmii-id" now not "rgmii". It also looks to match what's in v5.7 for the kernel. What do I need to do here next? Thanks!Quoted 4 lines
Quoted 2 lines
--
TomReverting
4346df3392c0makes your interface work?Yup.
Quoted 1 line
What is the DTS path that your hummingboard uses?
Good question. Per
board/solidrun/mx6cuboxi/mx6cuboxi.c:
/*
* This is not a perfect match. Avoid dependency on the DM GPIO driver
* needed
* for accurate board detection. Hummingboard2 DT is good enough for
* U-Boot on
* all Hummingboard/Cubox-i platforms.
*/
soarch/arm/dts/imx6dl-hummingboard2-emmc-som-v15.dtsis the base. But the board really is the original hummingboard platform. Thanks!Quoted 5 lines
Quoted 2 lines
--
TomDoes it work if you say
PHY_INTERFACE_MODE_RGMII_IDhere?
https://gitlab.denx.de/u-boot/u-boot/-/blob/master/drivers/net/fec_mxc.c#L1232Quoted 6 lines
No change. And to be clear, I bisect'd the issue down and at that commit, reverting it fixes ethernet. It doesn't revert cleanly (nor obviously to me) on master.
--
TomOn master, the revert would look like this:
drivers/net/phy/atheros.c +1
-0@@ -124,6 +124,7 @@ static int ar8021_config(struct phy_device *phydev)static int ar803x_delay_config (struct phy_device *phydev) { +int regval;int ret; if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID ||
drivers/net/phy/atheros.c static int ar803x_delay_config(struct phy_device *phydev) · line 147
Quoted 9 lines
drivers/net/phy/atheros.c +4
-0@@ -138,6 +139,10 @@ static int ar803x_delay_config(struct phy_device *phydev)else ret =ar803x_enable_rx_delay (phydev, false); +phy_write (phydev,MDIO_DEVAD_NONE ,0x1d ,0x05 ); + regval =phy_read (phydev,MDIO_DEVAD_NONE ,0x1e ); +phy_write (phydev,MDIO_DEVAD_NONE ,0x1e , (regval|0x0100 )); +return ret; }
This alone is not enough.
Quoted 5 lines
The next thing to check is to print the value of
phydev->interfacethere. 7 isPHY_INTERFACE_MODE_RGMII,
8 isPHY_INTERFACE_MODE_RGMII_ID,
9 isPHY_INTERFACE_MODE_RGMII_RXID,
10 isPHY_INTERFACE_MODE_RGMII_TXID,
With only this patch, it's 7. With this added to mx6cuboxi.c:
- phydev = phy_find_by_mask(bus, ETH_PHY_MASK, PHY_INTERFACE_MODE_RGMII);
+ phydev = phy_find_by_mask(bus, ETH_PHY_MASK, PHY_INTERFACE_MODE_RGMII_ID);
it's 8, and doesn't work either. Moving on to the next emails now.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200616/aa295474/attachment.sig>
Quoted 74 lines · Tom Rini
Quoted 72 lines · Vladimir Oltean
Quoted 46 lines · Tom Rini
Quoted 38 lines · Vladimir Oltean
Quoted 37 lines · Tom Rini
Quoted 15 lines · Vladimir Oltean
Hi Tom,
Quoted 12 lines · Tom Rini
Hey all,
In commit
4346df3392c0("phy: atheros: Make RGMII Tx delays actually configurable for AR8035") we brought in changes to get in to line with upstream linux kernel support for this PHY and in turn deal with more "driver was wrong, DT was wrong too" changes. Now the problem I have is that ethernet on my Hummingboard doesn't work AND as far as I can tell, the DTB is correct and saying phy-mode = "rgmii-id" now not "rgmii". It also looks to match what's in v5.7 for the kernel. What do I need to do here next? Thanks!Quoted 4 lines
Quoted 2 lines
--
TomReverting
4346df3392c0makes your interface work?Yup.
Quoted 1 line
What is the DTS path that your hummingboard uses?
Good question. Per
board/solidrun/mx6cuboxi/mx6cuboxi.c:
/*
* This is not a perfect match. Avoid dependency on the DM GPIO driver
* needed
* for accurate board detection. Hummingboard2 DT is good enough for
* U-Boot on
* all Hummingboard/Cubox-i platforms.
*/
soarch/arm/dts/imx6dl-hummingboard2-emmc-som-v15.dtsis the base. But the board really is the original hummingboard platform. Thanks!Quoted 5 lines
Quoted 2 lines
--
TomDoes it work if you say
PHY_INTERFACE_MODE_RGMII_IDhere?
https://gitlab.denx.de/u-boot/u-boot/-/blob/master/drivers/net/fec_mxc.c#L1232Quoted 6 lines
No change. And to be clear, I bisect'd the issue down and at that commit, reverting it fixes ethernet. It doesn't revert cleanly (nor obviously to me) on master.
--
TomOn master, the revert would look like this:
drivers/net/phy/atheros.c +1
-0@@ -124,6 +124,7 @@ static int ar8021_config(struct phy_device *phydev)static int ar803x_delay_config (struct phy_device *phydev) { +int regval;int ret; if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID ||@@ -138,6 +139,10 @@ static int ar803x_delay_config(struct phy_device *phydev)else ret =ar803x_enable_rx_delay (phydev, false);
Quoted 9 lines
drivers/net/phy/atheros.c static int ar803x_delay_config(struct phy_device *phydev) · line 147
Quoted 6 lines
drivers/net/phy/atheros.c +4
-0+phy_write (phydev,MDIO_DEVAD_NONE ,0x1d ,0x05 ); + regval =phy_read (phydev,MDIO_DEVAD_NONE ,0x1e ); +phy_write (phydev,MDIO_DEVAD_NONE ,0x1e , (regval|0x0100 )); +return ret; }This alone is not enough.
So if this is not enough, then I'd go back to bisecting. I'd rebase right after 8737c65fe4e3 ("phy: atheros: consolidate {ar8031|ar8035}_config()"), create a new patch on board/solidrun/mx6cuboxi/mx6cuboxi.c which changes RGMII to RGMII_ID, confirm it works (according to what you've said so far, it should), then bless it as "git bisect good", and let the fun start :)
Am 2020-06-16 23:57, schrieb Vladimir Oltean:
Quoted 85 lines · Tom Rini
Quoted 74 lines · Vladimir Oltean
Quoted 72 lines · Tom Rini
Quoted 46 lines · Vladimir Oltean
Quoted 38 lines · Tom Rini
Quoted 37 lines · Vladimir Oltean
Quoted 15 lines
Hi Tom,
Quoted 12 lines · Tom Rini
Hey all,
In commit
4346df3392c0("phy: atheros: Make RGMII Tx delays actually configurable for AR8035") we brought in changes to get in to line with upstream linux kernel support for this PHY and in turn deal with more "driver was wrong, DT was wrong too" changes. Now the problem I have is that ethernet on my Hummingboard doesn't work AND as far as I can tell, the DTB is correct and saying phy-mode = "rgmii-id" now not "rgmii". It also looks to match what's in v5.7 for the kernel. What do I need to do here next? Thanks!Quoted 4 lines
Quoted 2 lines
--
TomReverting
4346df3392c0makes your interface work?Yup.
Quoted 1 line
What is the DTS path that your hummingboard uses?
Good question. Per
board/solidrun/mx6cuboxi/mx6cuboxi.c:
/*
* This is not a perfect match. Avoid dependency on the DM GPIO driver
* needed
* for accurate board detection. Hummingboard2 DT is good enough for
* U-Boot on
* all Hummingboard/Cubox-i platforms.
*/
soarch/arm/dts/imx6dl-hummingboard2-emmc-som-v15.dtsis the base. But the board really is the original hummingboard platform. Thanks!Quoted 5 lines
Quoted 2 lines
--
TomDoes it work if you say
PHY_INTERFACE_MODE_RGMII_IDhere?
https://gitlab.denx.de/u-boot/u-boot/-/blob/master/drivers/net/fec_mxc.c#L1232Quoted 6 lines
No change. And to be clear, I bisect'd the issue down and at that commit, reverting it fixes ethernet. It doesn't revert cleanly (nor obviously to me) on master.
--
TomOn master, the revert would look like this:
drivers/net/phy/atheros.c +1
-0@@ -124,6 +124,7 @@ static int ar8021_config(struct phy_device *phydev)static int ar803x_delay_config (struct phy_device *phydev) { +int regval;int ret; if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID ||@@ -138,6 +139,10 @@ static int ar803x_delay_config(struct phy_device *phydev)else ret =ar803x_enable_rx_delay (phydev, false);Quoted 9 lines
drivers/net/phy/atheros.c static int ar803x_delay_config(struct phy_device *phydev) · line 147
Quoted 6 lines
drivers/net/phy/atheros.c +4
-0+phy_write (phydev,MDIO_DEVAD_NONE ,0x1d ,0x05 ); + regval =phy_read (phydev,MDIO_DEVAD_NONE ,0x1e ); +phy_write (phydev,MDIO_DEVAD_NONE ,0x1e , (regval|0x0100 )); +return ret; }This alone is not enough.
Quoted 6 lines
So if this is not enough, then I'd go back to bisecting. I'd rebase right after
8737c65fe4e3("phy: atheros: consolidate {ar8031|ar8035}_config()"), create a new patch onboard/solidrun/mx6cuboxi/mx6cuboxi.cwhich changes RGMII toRGMII_ID, confirm it works (according to what you've said so far, it should), then bless it as "git bisect good", and let the fun start :)
If these are the correct schematics, it looks like you also need the rgmii clock:
https://developer.solid-run.com/download/i-mx6-som-simplified-schematics-rev-1-5/
https://gitlab.denx.de/u-boot/u-boot/-/commit/6333cbb3817ed551cd7d4e92f7359c73ccc567fc
So I guess you'd need both, the clock output and the correct RGMII pad delay.
-michael
Am 16. Juni 2020 22:21:08 MESZ schrieb Vladimir Oltean <[email protected]>:
Quoted 44 lines · Tom Rini
Quoted 9 lines · Vladimir Oltean
Quoted 7 lines
Hi Tom,
Quoted 4 lines · Tom Rini
Hey all,
In commit
4346df3392c0("phy: atheros: Make RGMII Tx delaysactually
Quoted 1 line
Quoted 1 line
Quoted 1 line
configurable for AR8035") we brought in changes to get in to line
with
Quoted 1 line
Quoted 1 line
Quoted 1 line
upstream linux kernel support for this PHY and in turn deal with
more
Quoted 1 line
Quoted 1 line
Quoted 1 line
"driver was wrong, DT was wrong too" changes. Now the problem I
have is
Quoted 1 line
Quoted 1 line
Quoted 1 line
that ethernet on my Hummingboard doesn't work AND as far as I can
tell,
Quoted 1 line
Quoted 1 line
Quoted 1 line
the DTB is correct and saying phy-mode = "rgmii-id" now not
"rgmii". It
Quoted 1 line
Quoted 1 line
Quoted 1 line
also looks to match what's in v5.7 for the kernel. What do I
need to do
Quoted 7 lines
Quoted 6 lines
Quoted 4 lines
here next? Thanks!
--
TomReverting
4346df3392c0makes your interface work?Quoted 7 lines
Yup.
Quoted 1 line
What is the DTS path that your hummingboard uses?
Good question. Per
board/solidrun/mx6cuboxi/mx6cuboxi.c:
/*
* This is not a perfect match. Avoid dependency on the DM GPIOdriver
Quoted 6 lines
* needed
* for accurate board detection. Hummingboard2 DT is good enough for
* U-Boot on
* all Hummingboard/Cubox-i platforms.
*/
soarch/arm/dts/imx6dl-hummingboard2-emmc-som-v15.dtsis the base.
Quoted 8 lines
But
Quoted 4 lines
the board really is the original hummingboard platform. Thanks!
--
TomDoes it work if you say
PHY_INTERFACE_MODE_RGMII_IDhere?
https://gitlab.denx.de/u-boot/u-boot/-/blob/master/drivers/net/fec_mxc.c#L1232
it should be PHY_INTERFACE_MODE_RGMII_TXID to get the original behavior, shouldn't it? The commit in question only removes the hardcoded TX delay.
-michael
Quoted 48 lines · Michael Walle
Am 16. Juni 2020 22:21:08 MESZ schrieb Vladimir Oltean <[email protected]>:
Quoted 47 lines · Tom Rini
Quoted 9 lines · Vladimir Oltean
Quoted 7 lines
Hi Tom,
Quoted 4 lines · Tom Rini
Hey all,
In commit
4346df3392c0("phy: atheros: Make RGMII Tx delaysactually
Quoted 1 line
Quoted 1 line
Quoted 1 line
configurable for AR8035") we brought in changes to get in to line
with
Quoted 1 line
Quoted 1 line
Quoted 1 line
upstream linux kernel support for this PHY and in turn deal with
more
Quoted 1 line
Quoted 1 line
Quoted 1 line
"driver was wrong, DT was wrong too" changes. Now the problem I
have is
Quoted 1 line
Quoted 1 line
Quoted 1 line
that ethernet on my Hummingboard doesn't work AND as far as I can
tell,
Quoted 1 line
Quoted 1 line
Quoted 1 line
the DTB is correct and saying phy-mode = "rgmii-id" now not
"rgmii". It
Quoted 1 line
Quoted 1 line
Quoted 1 line
also looks to match what's in v5.7 for the kernel. What do I
need to do
Quoted 7 lines
Quoted 6 lines
Quoted 4 lines
here next? Thanks!
--
TomReverting
4346df3392c0makes your interface work?Quoted 7 lines
Yup.
Quoted 1 line
What is the DTS path that your hummingboard uses?
Good question. Per
board/solidrun/mx6cuboxi/mx6cuboxi.c:
/*
* This is not a perfect match. Avoid dependency on the DM GPIOdriver
Quoted 6 lines
* needed
* for accurate board detection. Hummingboard2 DT is good enough for
* U-Boot on
* all Hummingboard/Cubox-i platforms.
*/
soarch/arm/dts/imx6dl-hummingboard2-emmc-som-v15.dtsis the base.But
Quoted 2 lines
the board really is the original hummingboard platform. Thanks!
Quoted 7 lines
Quoted 5 lines
Quoted 2 lines
--
TomDoes it work if you say
PHY_INTERFACE_MODE_RGMII_IDhere?
https://gitlab.denx.de/u-boot/u-boot/-/blob/master/drivers/net/fec_mxc.c#L1232it should be
PHY_INTERFACE_MODE_RGMII_TXIDto get the original behavior, shouldn't it? The commit in question only removes the hardcoded TX delay.
This change alone also still fails on master for me.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200616/c1b2aaaf/attachment.sig>
Fabio Estevam
reviewerHi Tom,
Quoted 11 lines · Tom Rini
Hey all,
In commit
4346df3392c0("phy: atheros: Make RGMII Tx delays actually configurable for AR8035") we brought in changes to get in to line with upstream linux kernel support for this PHY and in turn deal with more "driver was wrong, DT was wrong too" changes. Now the problem I have is that ethernet on my Hummingboard doesn't work AND as far as I can tell, the DTB is correct and saying phy-mode = "rgmii-id" now not "rgmii". It also looks to match what's in v5.7 for the kernel. What do I need to do here next? Thanks!
mx6cuboxi_defconfig still needs to be converted to DM_ETH.
Unfortunately, I don't have access to my mx6cuboxi board to work on this.
Quoted 16 lines · Fabio Estevam
Hi Tom,
Quoted 11 lines · Tom Rini
Hey all,
In commit
4346df3392c0("phy: atheros: Make RGMII Tx delays actually configurable for AR8035") we brought in changes to get in to line with upstream linux kernel support for this PHY and in turn deal with more "driver was wrong, DT was wrong too" changes. Now the problem I have is that ethernet on my Hummingboard doesn't work AND as far as I can tell, the DTB is correct and saying phy-mode = "rgmii-id" now not "rgmii". It also looks to match what's in v5.7 for the kernel. What do I need to do here next? Thanks!
Quoted 3 lines
mx6cuboxi_defconfigstill needs to be converted toDM_ETH.Unfortunately, I don't have access to my mx6cuboxi board to work on this.
Oh, cool, thanks for the tip.
Tom, I'll spare you the suffering.
It's this one:
https://gitlab.denx.de/u-boot/u-boot/-/blob/master/board/solidrun/mx6cuboxi/mx6cuboxi.c#L324
-Vladimir
Quoted 15 lines · Fabio Estevam
Hi Tom,
Quoted 11 lines · Tom Rini
Hey all,
In commit
4346df3392c0("phy: atheros: Make RGMII Tx delays actually configurable for AR8035") we brought in changes to get in to line with upstream linux kernel support for this PHY and in turn deal with more "driver was wrong, DT was wrong too" changes. Now the problem I have is that ethernet on my Hummingboard doesn't work AND as far as I can tell, the DTB is correct and saying phy-mode = "rgmii-id" now not "rgmii". It also looks to match what's in v5.7 for the kernel. What do I need to do here next? Thanks!
Quoted 3 lines
mx6cuboxi_defconfigstill needs to be converted toDM_ETH.Unfortunately, I don't have access to my mx6cuboxi board to work on this.
Ah. So this is probably why the DT being right isn't helping then. If you want to blind-convert I'm happy to test, otherwise do you have a similar board conversion for me to look at? Thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200616/9b0acd49/attachment.sig>
Fabio Estevam
reviewerQuoted 3 lines · Tom Rini
Ah. So this is probably why the DT being right isn't helping then. If you want to blind-convert I'm happy to test, otherwise do you have a similar board conversion for me to look at? Thanks!
Please try Vladimir's suggestion as it seems to be the less intrusive approach:
board/solidrun/mx6cuboxi/mx6cuboxi.c +1 -1
@@ -321,7 +321,7 @@ int board_eth_init(bd_t *bis)if (!bus)return -EINVAL ; - phydev =phy_find_by_mask (bus,ETH_PHY_MASK ,PHY_INTERFACE_MODE_RGMII ); + phydev = phy_find_by_mask(bus, ETH_PHY_MASK,
PHY_INTERFACE_MODE_RGMII_ID);
if (!phydev) {
ret = -EINVAL;
goto free_bus;Here is a similar DM_ETH board conversion:
commit 02ee7a4aa57b37d6003263b69b1852c4cda5975e
Author: Alifer Moraes <[email protected]> Date: Mon Feb 10 11:28:01 2020 -0300
mx6sabresd: Convert ethernet to driver model
Convert imx6sabresd ethernet to driver model to fix the following warning:
===================== WARNING ====================== This board does not use CONFIG_DM_ETH (Driver Model for Ethernet drivers). Please update the board to use CONFIG_DM_ETH before the v2020.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info.
====================================================
Let us know if this helps.
Quoted 19 lines · Fabio Estevam
Quoted 3 lines · Tom Rini
Ah. So this is probably why the DT being right isn't helping then. If you want to blind-convert I'm happy to test, otherwise do you have a similar board conversion for me to look at? Thanks!
Please try Vladimir's suggestion as it seems to be the less intrusive approach:
board/solidrun/mx6cuboxi/mx6cuboxi.c +1
-1@@ -321,7 +321,7 @@ int board_eth_init(bd_t *bis)if (!bus)return -EINVAL ; - phydev =phy_find_by_mask (bus,ETH_PHY_MASK ,PHY_INTERFACE_MODE_RGMII ); + phydev =phy_find_by_mask (bus,ETH_PHY_MASK ,PHY_INTERFACE_MODE_RGMII_ID );if (!phydev) { ret = -EINVAL ;
Quoted 2 lines
goto free_bus;
OK, tried that and not enough. Console says PHY autoneg completes, but DHCP still doesn't reply.
Quoted 18 lines
Here is a similar
DM_ETHboard conversion:commit
02ee7a4aa57b37d6003263b69b1852c4cda5975eAuthor: Alifer Moraes <[email protected]> Date: Mon Feb 10 11:28:01 2020 -0300mx6sabresd: Convert ethernet to driver model
Convert imx6sabresd ethernet to driver model to fix the following warning:
===================== WARNING ====================== This board does not use
CONFIG_DM_ETH(Driver Model for Ethernet drivers). Please update the board to useCONFIG_DM_ETHbefore the v2020.07 release. Failure to update by the deadline may result in board removal. Seedoc/driver-model/migration.rstfor more info.
====================================================
Quoted 4 lines
Signed-off-by Alifer Moraes <[email protected]>Reviewed-by Fabio Estevam <[email protected]>Let us know if this helps.
I'm looking at the conversion now, thanks.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200616/c0591ab8/attachment.sig>
Quoted 1 line · Tom Rini
I'm looking at the conversion now, thanks.
When doing the DM_ETH conversion, this kernel commit may also help as 'qca,clk-out-frequency' is also supported in U-Boot:
commit 86b08bd5b99480b79a25343f24c1b8c4ddcb5c09
Author: Russell King <[email protected]> Date: Wed Apr 15 16:44:17 2020 +0100
ARM: dts: imx6-sr-som: add ethernet PHY configuration
Add ethernet PHY configuration ahead of removing the quirk that configures the clocking mode for the PHY. The RGMII delay is already set correctly.
Quoted 13 lines · Fabio Estevam
Quoted 1 line · Tom Rini
I'm looking at the conversion now, thanks.
When doing the
DM_ETHconversion, this kernel commit may also help as 'qca,clk-out-frequency' is also supported in U-Boot:commit
86b08bd5b99480b79a25343f24c1b8c4ddcb5c09Author: Russell King <[email protected]> Date: Wed Apr 15 16:44:17 2020 +0100ARM: dts: imx6-sr-som: add ethernet PHY configuration
Quoted 7 lines
Add ethernet PHY configuration ahead of removing the quirk that configures the clocking mode for the PHY. The RGMII delay is already set correctly.
Signed-off-by Russell King <[email protected]>Reviewed-by Fabio Estevam <[email protected]>Signed-off-by Shawn Guo <[email protected]>
Yeah, OK, I got far enough on trying to convert this that I see I don't quite have time to pick it up and run with it. It looks like there's going to be some extra fun around resetting the PHY perhaps? My quick pass got things seeing a generic PHY and not the atheros one. If you have time to make something you'd like me to test for conversion let me know. But I'm going to pick up debugging the problem I see on the platform right now in case there's a wider problem it's showing.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200616/a84e301f/attachment.sig>
Fabio Estevam
reviewerHi Tom,
Quoted 7 lines · Tom Rini
Yeah, OK, I got far enough on trying to convert this that I see I don't quite have time to pick it up and run with it. It looks like there's going to be some extra fun around resetting the PHY perhaps? My quick pass got things seeing a generic PHY and not the atheros one. If you have time to make something you'd like me to test for conversion let me know. But I'm going to pick up debugging the problem I see on the platform right now in case there's a wider problem it's showing.
Here are two untested patches you could try.
-------------- next part --------------
A non-text attachment was scrubbed...
Name: 0001-imx6qdlsrsomupdate.patch
Type: text/x-patch
Size: 1653 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200617/bdfa34fa/attachment.bin>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: 0002-cuboxdmethconversion.patch
Type: text/x-patch
Size: 5319 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200617/bdfa34fa/attachment-0001.bin>
Fabio Estevam
reviewerQuoted 13 lines · Fabio Estevam
Hi Tom,
Quoted 7 lines · Tom Rini
Yeah, OK, I got far enough on trying to convert this that I see I don't quite have time to pick it up and run with it. It looks like there's going to be some extra fun around resetting the PHY perhaps? My quick pass got things seeing a generic PHY and not the atheros one. If you have time to make something you'd like me to test for conversion let me know. But I'm going to pick up debugging the problem I see on the platform right now in case there's a wider problem it's showing.
Quoted 1 line
Here are two untested patches you could try.
Just tested Ethernet on a mx6qsabresd board and I see Ethernet is broken in master. It works fine in 2020.04.
Reverting 4346df3392c0 ("phy: atheros: Make RGMII Tx delays actually configurable for AR8035") did not help.
git bisect is running into problems:
Error: Cannot open output filescripts/Makefile.spl:465: recipe for target 'spl/dts/imx6dl-sabresd.dtb' failed make[1]: *** [spl/dts/imx6dl-sabresd.dtb] Error 1
make[1]: *** Waiting for unfinished jobs....
UPD spl/./include/generated/asm-offsets.h
UPD spl/./include/generated/generic-asm-offsets.h
Makefile:1940: recipe for target 'spl/u-boot-spl' failed
make: *** [spl/u-boot-spl] Error 2
So not able to run a bit bisect.
Quoted 33 lines · Fabio Estevam
Quoted 13 lines · Fabio Estevam
Hi Tom,
Quoted 7 lines · Tom Rini
Yeah, OK, I got far enough on trying to convert this that I see I don't quite have time to pick it up and run with it. It looks like there's going to be some extra fun around resetting the PHY perhaps? My quick pass got things seeing a generic PHY and not the atheros one. If you have time to make something you'd like me to test for conversion let me know. But I'm going to pick up debugging the problem I see on the platform right now in case there's a wider problem it's showing.
Quoted 1 line
Here are two untested patches you could try.
Just tested Ethernet on a mx6qsabresd board and I see Ethernet is broken in master. It works fine in 2020.04.
Reverting
4346df3392c0("phy: atheros: Make RGMII Tx delays actually configurable for AR8035") did not help.git bisect is running into problems:
Error: Cannot open output file
scripts/Makefile.spl:465: recipe for target 'spl/dts/imx6dl-sabresd.dtb' failed make[1]: *** [spl/dts/imx6dl-sabresd.dtb] Error 1
make[1]: *** Waiting for unfinished jobs....
UPDspl/./include/generated/asm-offsets.h
UPDspl/./include/generated/generic-asm-offsets.h
Makefile:1940: recipe for target 'spl/u-boot-spl' failed
make: *** [spl/u-boot-spl] Error 2
Quoted 1 line
So not able to run a bit bisect.
You probably need 5f09f9af3cc335fe6a74c031cfa0b1d8bdf4b9db applied when you see that failure, or a smaller make -j number.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200617/edf459ce/attachment.sig>
Fabio Estevam
reviewerQuoted 2 lines · Tom Rini
You probably need
5f09f9af3cc335fe6a74c031cfa0b1d8bdf4b9dbapplied when you see that failure, or a smaller make -j number.
Ok, I fixed the issue for mx6sabresd. It was dts problem. I will send the patch.
Quoted 12 lines · Fabio Estevam
Hi Tom,
Quoted 7 lines · Tom Rini
Yeah, OK, I got far enough on trying to convert this that I see I don't quite have time to pick it up and run with it. It looks like there's going to be some extra fun around resetting the PHY perhaps? My quick pass got things seeing a generic PHY and not the atheros one. If you have time to make something you'd like me to test for conversion let me know. But I'm going to pick up debugging the problem I see on the platform right now in case there's a wider problem it's showing.
Quoted 1 line
Here are two untested patches you could try.
Based on your follow-up patches, I think you'll be unsurprised it doesn't work. I get:
Net: Could not get PHY for FEC0: addr 0
Now, question:
Quoted 8 lines
(quoted diff) +0
-8- ret = dm_gpio_lookup_name("GPIO4_15", &desc); - if (ret) { - printf("%s: phy reset lookup failed\n", __func__); - return; - } - - ret = dm_gpio_request(&desc, "phy-reset"); - if (ret) {
Review
Quoted 10 lines
(quoted diff) +0
-10- printf("%s: phy reset request failed\n", __func__); - return; - } - - gpio_direction_output(ETH_PHY_RESET, 0); - mdelay(10); - gpio_set_value(ETH_PHY_RESET, 1); - udelay(100); - - gpio_free_list_nodev(&desc, 1);
Don't we need that still, but in a setup_fec() call? I have a quick test with:
board/solidrun/mx6cuboxi/mx6cuboxi.c +53 -9
@@ -17,6 +17,7 @@#include <image.h> #include <init.h> #include <log.h> +#include <net.h> #include <asm/arch/clock.h> #include <asm/arch/imx-regs.h> #include <asm/arch/iomux.h>
@@ -33,6 +34,7 @@#include <fsl_esdhc_imx.h> #include <malloc.h> #include <miiphy.h> +#include <netdev.h> #include <asm/arch/crm_regs.h> #include <asm/io.h> #include <asm/arch/sys_proto.h>
@@ -50,15 +52,6 @@ DECLARE_GLOBAL_DATA_PTR; PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ PAD_CTL_SRE_FAST | PAD_CTL_HYS) -#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ - PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) - -#define ENET_PAD_CTRL_PD (PAD_CTL_PUS_100K_DOWN | \ - PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) - -#define ENET_PAD_CTRL_CLK ((PAD_CTL_PUS_100K_UP & ~PAD_CTL_PKE) | \ - PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) -#define ETH_PHY_RESET IMX_GPIO_NR(4, 15)#define USB_H1_VBUS IMX_GPIO_NR(1, 0)
@@ -235,6 +228,51 @@ int board_mmc_init(bd_t *bis)return 0 ; } +#ifdef CONFIG_FEC_MXC +static int setup_fec (void ) +{ +struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR ; +struct gpio_desc desc; + +int ret =enable_fec_anatop_clock (0 ,ENET_25MHZ ); +if (ret) +return ret; + +/* set gpr1[ENET_CLK_SEL] */ +setbits_le32 (&iomuxc_regs->gpr[1 ],IOMUXC_GPR1_ENET_CLK_SEL_MASK ); + +/* Reset PHY */ + ret =dm_gpio_lookup_name ("GPIO4_15" , &desc); +if (ret) { +printf ("%s: phy reset lookup failed\n" , __func__); +return ret; + } + + ret =dm_gpio_request (&desc,"phy-reset" ); +if (ret) { +printf ("%s: phy reset request failed\n" , __func__); +return ret; + } + +gpio_direction_output (ETH_PHY_RESET ,0 ); +mdelay (10 ); +gpio_set_value (ETH_PHY_RESET ,1 ); +udelay (100 ); + +gpio_free_list_nodev (&desc,1 ); + +return 0 ; +} +#endif + +int board_phy_config (struct phy_device *phydev) +{ +if (phydev->drv->config) + phydev->drv->config (phydev); + +return 0 ; +} +#ifdef CONFIG_VIDEO_IPUV3 static void do_enable_hdmi (struct display_info_t const *dev) {
@@ -344,6 +382,12 @@ int board_init(void)/* address of boot parameters */ gd->bd->bi_boot_params =CONFIG_SYS_SDRAM_BASE +0x100 ; +#ifdef CONFIG_FEC_MXC + ret =setup_fec (); +if (ret) +return ret; +#endif +#ifdef CONFIG_VIDEO_IPUV3 ret =setup_display ();#endif
And at run-time I get:
Warning: ethernet at 2188000 using MAC address from ROM
eth0: ethernet at 2188000
...
=> mdio list
FEC0:
0 - AR8035 <--> ethernet at 2188000
And I did the mdio write/read's from the previous part of the thread and get the same values.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200617/c20b9ef4/attachment.sig>
Fabio Estevam
reviewerQuoted 20 lines · Tom Rini
(quoted diff) +20
-0+#ifdef CONFIG_FEC_MXC +static int setup_fec(void) +{ + struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; + struct gpio_desc desc; + + int ret = enable_fec_anatop_clock(0, ENET_25MHZ); + if (ret) + return ret; + + /* set gpr1[ENET_CLK_SEL] */ + setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK); + + /* Reset PHY */ + ret = dm_gpio_lookup_name("GPIO4_15", &desc); + if (ret) { + printf("%s: phy reset lookup failed\n", __func__); + return ret; + } +
Review
Quoted 10 lines
(quoted diff) +10
-0+ ret = dm_gpio_request(&desc, "phy-reset"); + if (ret) { + printf("%s: phy reset request failed\n", __func__); + return ret; + } + + gpio_direction_output(ETH_PHY_RESET, 0); + mdelay(10); + gpio_set_value(ETH_PHY_RESET, 1); + udelay(100);
The Ethernet PHY reset can be done via device tree.
It seems we need to change it like this:
arch/arm/dts/imx6qdl-sr-som.dtsi +2 -1
@@ -54,7 +54,8 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_microsom_enet_ar8035>; phy-mode = "rgmii-id"; - phy-reset-duration = <2>; + phy-reset-duration = <10>; + phy-reset-post-delay = <1>; phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; status = "okay"; };
Does it still probe if you remove the PHY reset from the board code?
Fabio Estevam
reviewerQuoted 1 line · Fabio Estevam
Does it still probe if you remove the PHY reset from the board code?
Another suggestion: please use the ar8031_phy_fixup() and board_phy_config() from mx6sabresd into cubox board file to see if Ethernet works.
Quoted 7 lines · Fabio Estevam
Quoted 1 line · Fabio Estevam
Does it still probe if you remove the PHY reset from the board code?
Another suggestion: please use the
ar8031_phy_fixup()andboard_phy_config()from mx6sabresd into cubox board file to see if Ethernet works.
Literal copy and paste and same failure.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200617/3f0040e1/attachment.sig>
Quoted 50 lines · Fabio Estevam
Quoted 20 lines · Tom Rini
(quoted diff) +20
-0+#ifdef CONFIG_FEC_MXC +static int setup_fec(void) +{ + struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; + struct gpio_desc desc; + + int ret = enable_fec_anatop_clock(0, ENET_25MHZ); + if (ret) + return ret; + + /* set gpr1[ENET_CLK_SEL] */ + setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK); + + /* Reset PHY */ + ret = dm_gpio_lookup_name("GPIO4_15", &desc); + if (ret) { + printf("%s: phy reset lookup failed\n", __func__); + return ret; + } +Review
Quoted 10 lines
(quoted diff) +10
-0+ ret = dm_gpio_request(&desc, "phy-reset"); + if (ret) { + printf("%s: phy reset request failed\n", __func__); + return ret; + } + + gpio_direction_output(ETH_PHY_RESET, 0); + mdelay(10); + gpio_set_value(ETH_PHY_RESET, 1); + udelay(100);The Ethernet PHY reset can be done via device tree.
It seems we need to change it like this:
arch/arm/dts/imx6qdl-sr-som.dtsi +2
-1@@ -54,7 +54,8 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_microsom_enet_ar8035>; phy-mode = "rgmii-id"; - phy-reset-duration = <2>; + phy-reset-duration = <10>; + phy-reset-post-delay = <1>; phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; status = "okay"; };
Quoted 1 line
Does it still probe if you remove the PHY reset from the board code?
Nope, same "Could not get PHY for FEC0: addr 0". I gather from another part of this thread there's some further breakage / unexpected changes, so I'll chime in there next.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200617/3bf7ae20/attachment.sig>
Fabio Estevam
reviewerHi Tom,
Quoted 3 lines · Tom Rini
Based on your follow-up patches, I think you'll be unsurprised it doesn't work. I get:
Net: Could not get PHY for FEC0: addr 0
Now I understand why the PHY could not be found with the patches I sent.
On mx6cubox the AR8035 is clocked from a 25MHz clock coming from the i.MX6 GPIO16 pin.
My patch incorrectly removed this setting.
board/solidrun/mx6cuboxi/mx6cuboxi.c int board_mmc_init(bd_t *bis) · line 242
Quoted 6 lines
board/solidrun/mx6cuboxi/mx6cuboxi.c +6
-0+int ret =enable_fec_anatop_clock (0 ,ENET_25MHZ ); +if (ret) +return ret; + +/* set gpr1[ENET_CLK_SEL] */ +setbits_le32 (&iomuxc_regs->gpr[1 ],IOMUXC_GPR1_ENET_CLK_SEL_MASK );
enable_fec_anatop_clock() and GPR1 settings above must remain.
In order to get patch 1 to work (the one that adds the qca,clk-out-frequency property ) you also need this FEC change:
https://pastebin.com/raw/mcKdwwTs
I hope this helps.
Quoted 22 lines · Fabio Estevam
Hi Tom,
Quoted 3 lines · Tom Rini
Based on your follow-up patches, I think you'll be unsurprised it doesn't work. I get:
Net: Could not get PHY for FEC0: addr 0Now I understand why the PHY could not be found with the patches I sent.
On mx6cubox the AR8035 is clocked from a 25MHz clock coming from the i.MX6 GPIO16 pin.
My patch incorrectly removed this setting.
board/solidrun/mx6cuboxi/mx6cuboxi.c int board_mmc_init(bd_t *bis) · line 242
Quoted 6 lines
board/solidrun/mx6cuboxi/mx6cuboxi.c +6
-0+int ret =enable_fec_anatop_clock (0 ,ENET_25MHZ ); +if (ret) +return ret; + +/* set gpr1[ENET_CLK_SEL] */ +setbits_le32 (&iomuxc_regs->gpr[1 ],IOMUXC_GPR1_ENET_CLK_SEL_MASK );
Quoted 7 lines
enable_fec_anatop_clock()and GPR1 settings above must remain.In order to get patch 1 to work (the one that adds the qca,clk-out-frequency property ) you also need this FEC change:
https://pastebin.com/raw/mcKdwwTsI hope this helps.
I'll test that out tomorrow. But my question now is, what do you want to do about the various platforms where ethernet isn't working?
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200617/6b98955a/attachment.sig>
Fabio Estevam
reviewerQuoted 2 lines · Tom Rini
I'll test that out tomorrow. But my question now is, what do you want to do about the various platforms where ethernet isn't working?
I fixed the mx6sabresd Ethernet regression today and I can also try to convert other imx platforms from rgmii to rgmi-id.
We still don't have the root cause for the mx6cuboxi regression.
What are the other platforms where ethernet isn't working?
Quoted 11 lines · Fabio Estevam
Quoted 2 lines · Tom Rini
I'll test that out tomorrow. But my question now is, what do you want to do about the various platforms where ethernet isn't working?
I fixed the mx6sabresd Ethernet regression today and I can also try to convert other imx platforms from rgmii to rgmi-id.
We still don't have the root cause for the mx6cuboxi regression.
What are the other platforms where ethernet isn't working?
It's a good question what else doesn't work. What has been actively verified at this point?
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200618/9c29a65d/attachment.sig>
Fabio Estevam
reviewerHi Tom,
Quoted 2 lines · Tom Rini
It's a good question what else doesn't work. What has been actively verified at this point?
After the fixes I sent yesterday, the few imx boards I have access at the moment have Ethernet working well.
Quoted 10 lines · Fabio Estevam
Hi Tom,
Quoted 2 lines · Tom Rini
It's a good question what else doesn't work. What has been actively verified at this point?
After the fixes I sent yesterday, the few imx boards I have access at the moment have Ethernet working well.
I tested current master (v2020.07-rc5 + imx fixes) on tbs2910 (imx6q + atheros PHY).
Unfortunately ethernet is broken now, while it used to work well on u-boot version v2020.04. Ethernet support was copied from imx6q-sabresd, the recently for sabresd fixed phy-mode already is rgmii-id for tbs2910.
Any ideas what could be wrong?
Thanks,
Soeren
Fabio Estevam
reviewerHi Soeren,
Quoted 7 lines · Soeren Moch
I tested current master (v2020.07-rc5 + imx fixes) on tbs2910 (imx6q + atheros PHY).
Unfortunately ethernet is broken now, while it used to work well on u-boot version v2020.04. Ethernet support was copied from imx6q-sabresd, the recently for sabresd fixed phy-mode already is rgmii-id for tbs2910.Any ideas what could be wrong?
I just tested mainline U-Boot and Ethernet works fine on a imx6qp sabresd board:
U-Boot SPL 2020.07-rc5-00052-g922c6d5d00 (Jun 24 2020 - 16:21:27 -0300) Trying to boot from MMC1
U-Boot 2020.07-rc5-00052-g922c6d5d00 (Jun 24 2020 - 16:21:27 -0300)
CPU: Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz) CPU: Automotive temperature grade (-40C to 125C) at 30C Reset cause: POR Model: Freescale i.MX6 Quad Plus SABRE Smart Device Board Board: MX6-SabreSD I2C: ready DRAM: 1 GiB PMIC: PFUZE100 ID=0x10 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 3 Loading Environment from MMC... OK No panel detected: default to Hannstar-XGA Display: Hannstar-XGA (1024x768) In: serial Out: serial Err: serial Net: eth0: ethernet at 2188000 Hit any key to stop autoboot: 0
=> dhcp zImage
BOOTP broadcast 1
DHCP client bound to address 192.168.0.24 (50 ms)
Using ethernet at 2188000 device
TFTP from server 192.168.0.12; our IP address is 192.168.0.24 Filename 'zImage'.
Load address: 0x12000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#############################################################
1.3 MiB/sdone
Bytes transferred = 9468928 (907c00 hex)
=> mdio list
FEC0:
1 - AR8031/AR8033 <--> ethernet at 2188000
=>
What is the exact failure you see? Is the Ethernet PHY found at the correct address and probed?
On tbs2910 does the AR8031 generate a 125MHz clock to the i.MX6Q Ethernet?
If so, does the change below help (I am assuming the PHY is located at address 1, if not, please adjust the @ and reg accordingly)?
arch/arm/dts/imx6q-tbs2910.dts +10 -0
@@ -108,6 +108,16 @@ phy-mode = "rgmii-id"; phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy: ethernet-phy at 1 { + reg = <1>; + qca,clk-out-frequency = <125000000>; + }; + }; };
In case you still have issues, please share the tbs2910 schematics with me offline so I can try to understand the failure.
Hi Fabio
Quoted 61 lines · Fabio Estevam
Hi Soeren,
Quoted 7 lines · Soeren Moch
I tested current master (v2020.07-rc5 + imx fixes) on tbs2910 (imx6q + atheros PHY).
Unfortunately ethernet is broken now, while it used to work well on u-boot version v2020.04. Ethernet support was copied from imx6q-sabresd, the recently for sabresd fixed phy-mode already is rgmii-id for tbs2910.Any ideas what could be wrong?
I just tested mainline U-Boot and Ethernet works fine on a imx6qp sabresd board:
U-Boot SPL 2020.07-rc5-00052-g922c6d5d00 (Jun 24 2020 - 16:21:27 -0300) Trying to boot from MMC1
U-Boot 2020.07-rc5-00052-g922c6d5d00 (Jun 24 2020 - 16:21:27 -0300)
CPU: Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz) CPU: Automotive temperature grade (-40C to 125C) at 30C Reset cause: POR Model: Freescale i.MX6 Quad Plus SABRE Smart Device Board Board: MX6-SabreSD I2C: ready DRAM: 1 GiB PMIC: PFUZE100 ID=0x10 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 3 Loading Environment from MMC... OK No panel detected: default to Hannstar-XGA Display: Hannstar-XGA (1024x768) In: serial Out: serial Err: serial Net: eth0: ethernet at 2188000 Hit any key to stop autoboot: 0=> dhcp zImage
BOOTP broadcast 1
DHCP client bound to address 192.168.0.24 (50 ms)
Using ethernet at 2188000 device
TFTP from server 192.168.0.12; our IP address is 192.168.0.24 Filename 'zImage'.
Load address:0x12000000
Loading: ################################################################################################################################## ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################# 1.3 MiB/sdone
Bytes transferred = 9468928 (907c00 hex)
=> mdio list
FEC0:
1 - AR8031/AR8033 <--> ethernet at 2188000
=>
Quoted 2 lines
What is the exact failure you see? Is the Ethernet PHY found at the correct address and probed?
From what I see nothing is obviously wrong, just no ethernet connection:
U-Boot 2020.07-rc5-00039-g4ff63383e3-dirty (Jun 24 2020 - 21:48:31 +0200)?????? ???????????????????????????????????????????????????????????????????????????????
CPU:?? Freescale i.MX6Q rev1.2 at 792MHz???????????????????????????????????????
CPU:?? Commercial temperature grade (0C to 95C) at 42C?????????????????????????
Reset cause:
POR???????????????????????????????????????????????????????????????
Model: TBS2910 Matrix ARM mini PC??????????????????????????????????????????????
DRAM:? 2 GiB??????????????????????????????????????????????????????????????????? MMC:?? FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC:
2???????????????????????????????????
Loading Environment from MMC... OK?????????????????????????????????????????????
No panel detected: default to HDMI?????????????????????????????????????????????
Display: HDMI (1024x768)??????????????????????????????????????????????????????? In:??? serial?????????????????????????????????????????????????????????????????? Out:?? vga????????????????????????????????????????????????????????????????????? Err:?? vga????????????????????????????????????????????????????????????????????? Net:?? eth0:
ethernet at 2188000?????????????????????????????????????????????????? PCI:???????????????????????????????????????????????????????????????????????????
PCI:?? pcie phy link never came up?????????????????????????????????????????????
No such bus???????????????????????????????????????????????????????????????????? starting USB...???????????????????????????????????????????????????????????????? Bus usb at 2184000: usb dr_mode not found?????????????????????????????????????????
Bus usb at 2184200: USB EHCI 1.00?????????????????????????????????????????????????
scanning bus usb at 2184000 for devices... 1 USB Device(s) found??????????????????
scanning bus usb at 2184200 for devices... 4 USB Device(s) found??????????????????
?????? scanning usb for storage devices... 0 Storage Device(s) found???????????
Hit any key to stop autoboot:? 0???????????????????????????????????????????????
Matrix U-Boot> dhcp???????????????????????????????????????????????????????????? BOOTP broadcast 1?????????????????????????????????????????????????????????????? BOOTP broadcast 2?????????????????????????????????????????????????????????????? BOOTP broadcast 3?????????????????????????????????????????????????????????????? BOOTP broadcast 4?????????????????????????????????????????????????????????????? BOOTP broadcast 5?????????????????????????????????????????????????????????????? BOOTP broadcast 6?????????????????????????????????????????????????????????????? BOOTP broadcast 7?????????????????????????????????????????????????????????????? BOOTP broadcast 8?????????????????????????????????????????????????????????????? BOOTP broadcast 9?????????????????????????????????????????????????????????????? BOOTP broadcast 10????????????????????????????????????????????????????????????? BOOTP broadcast 11????????????????????????????????????????????????????????????? BOOTP broadcast 12????????????????????????????????????????????????????????????? BOOTP broadcast 13????????????????????????????????????????????????????????????? BOOTP broadcast 14????????????????????????????????????????????????????????????? BOOTP broadcast 15????????????????????????????????????????????????????????????? BOOTP broadcast 16????????????????????????????????????????????????????????????? BOOTP broadcast 17????????????????????????????????????????????????????????????? ???????????????????????????????????????????????????????????????????????????????
Retry time exceeded; starting again????????????????????????????????????????????
Matrix U-Boot> mdio list??????????????????????????????????????????????????????? FEC0:??????????????????????????????????????????????????????????????????????????
4 - AR8035 <-->
ethernet at 2188000??????????????????????????????????????????????? Matrix U-Boot>
Quoted 12 lines
On tbs2910 does the AR8031 generate a 125MHz clock to the i.MX6Q Ethernet?
If so, does the change below help (I am assuming the PHY is located at address 1, if not, please adjust the @ and reg accordingly)?
arch/arm/dts/imx6q-tbs2910.dts +1
-0@@ -108,6 +108,16 @@ phy-mode = "rgmii-id"; phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; status = "okay"; +
arch/arm/dts/imx6q-tbs2910.dts line 121
Quoted 10 lines
arch/arm/dts/imx6q-tbs2910.dts +9
-0+ mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy: ethernet-phy at 1 { + reg = <1>; + qca,clk-out-frequency = <125000000>; + }; + }; };
I used this patch with address 4 (that's why the -dirty in the u-boot version), no luck.
It seems I have a AR8035 PHY.
Quoted 3 lines
In case you still have issues, please share the tbs2910 schematics with me offline so I can try to understand the failure.
Schematics are at
https://www.tbsdtv.com/download/document/tbs2910/TBS2910-Matrix-ARM-mini-PC-SCH_rev2.1.pdf
Thanks for your help,
Soeren
Fabio Estevam
reviewerHi Soeren,
Quoted 2 lines · Soeren Moch
Schematics are at
https://www.tbsdtv.com/download/document/tbs2910/TBS2910-Matrix-ARM-mini-PC-SCH_rev2.1.pdf
Here is another patch for you to try:
https://pastebin.com/raw/Dkipgq1n
Hi Fabio,
Quoted 8 lines · Fabio Estevam
Hi Soeren,
Quoted 2 lines · Soeren Moch
Schematics are at
https://www.tbsdtv.com/download/document/tbs2910/TBS2910-Matrix-ARM-mini-PC-SCH_rev2.1.pdfHere is another patch for you to try:
https://pastebin.com/raw/Dkipgq1n
Still no luck:
U-Boot 2020.07-rc5-00039-g4ff63383e3-dirty (Jun 24 2020 - 22:36:43 +0200)
CPU:?? Freescale i.MX6Q rev1.2 at 792MHz
CPU:?? Commercial temperature grade (0C to 95C) at 47C Reset cause: POR
Model: TBS2910 Matrix ARM mini PC
DRAM:? 2 GiB
MMC:?? FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
No panel detected: default to HDMI
Display: HDMI (1024x768)
In:??? serial
Out:?? vga
Err:?? vga
Net:?? eth0: ethernet at 2188000
PCI:
PCI:?? pcie phy link never came up
No such bus
starting USB...
Bus usb at 2184000: usb dr_mode not found
Bus usb at 2184200: USB EHCI 1.00
scanning bus usb at 2184000 for devices... 1 USB Device(s) found scanning bus usb at 2184200 for devices... 4 USB Device(s) found ?????? scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot:? 0
Matrix U-Boot> dhcp
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
BOOTP broadcast 6
BOOTP broadcast 7
BOOTP broadcast 8
BOOTP broadcast 9
BOOTP broadcast 10
BOOTP broadcast 11
BOOTP broadcast 12
BOOTP broadcast 13
BOOTP broadcast 14
BOOTP broadcast 15
BOOTP broadcast 16
BOOTP broadcast 17
Retry time exceeded; starting again
Matrix U-Boot> mdio list
FEC0:
4 - AR8035 <--> ethernet at 2188000
Matrix U-Boot>
Fabio Estevam
reviewerHi Soeren,
Quoted 1 line · S?ren Moch
Still no luck:
mx6cuboxi has an AR8035 too and it is working fine in U-Boot mainline.
I am not sure why tbs2910 is failing. Could you try to bisect?
Hi Fabio,
Quoted 10 lines · Fabio Estevam
Hi Soeren,
Quoted 1 line · S?ren Moch
Still no luck:
mx6cuboxi has an AR8035 too and it is working fine in U-Boot mainline.
I am not sure why tbs2910 is failing. Could you try to bisect?
Unfortunately I have no access to my usual development board (and will not have until the v2020.07 release). I only can use an old board without working USB-OTG, limited to eMMC boot. So I tried to avoid bisecting, because a bad commit could completely brick this board.
Is there a reliable way to start a new u-boot directly from a running u-boot?
Soeren
Hi Soeren,
Quoted 4 lines · Soeren Moch
Unfortunately I have no access to my usual development board (and will not have until the v2020.07 release). I only can use an old board without working USB-OTG, limited to eMMC boot. So I tried to avoid bisecting, because a bad commit could completely brick this board.
Ok, understood.
We could check if the issue on your board is due to:
commit 6333cbb3817ed551cd7d4e92f7359c73ccc567fc
Author: Michael Walle <[email protected]> Date: Thu May 7 00:11:58 2020 +0200
phy: atheros: ar8035: remove static clock config
We can configure the clock output in the device tree. Disable the hardcoded one in here. This is highly board-specific and should have never been enabled in the PHY driver.
If bisecting shows that this commit breaks your board it probably depends on the clock output of your Atheros AR8035 PHY. Please have a look at doc/device-tree-bindings/net/phy/atheros.txt. You need to set "clk-out-frequency = <125000000>" because that value was the hardcoded value until this commit.
On your board, are you able to measure with a scope the AR8035 CLK_25M pin?
Prior to this commit the CLK_25M was hardcoded to output a 125MHz clock.
Now that this setting from the ar8035 phy driver is gone we should pass this information in some form:
- We tried via devicetree with the "qca,clk-out-frequency" property, but it did not work. This is an area where you could add some debug prints inside drivers/net/phy/atheros.c and see if if qca,clk-out-frequency is being parsed correctly to configure a 125MHz clock output. This is the method I used on mx6cuboxi last week and it works.
- Other way to configure the AR803x is via board code. Please try to copy the ar8031_phy_fixup() and board_phy_config() from board/freescale/mx6sabresd/mx6sabresd.c into your board file.
(I plan to remove this board PHY code in mx6sabresd after 2020.07 and use "qca,clk-out-frequency" to do the job).
Fabio Estevam
reviewerQuoted 6 lines · Fabio Estevam
- We tried via devicetree with the "qca,clk-out-frequency" property, but it did not work. This is an area where you could add some debug prints inside
drivers/net/phy/atheros.cand see if if qca,clk-out-frequency is being parsed correctly to configure a 125MHz clock output. This is the method I used on mx6cuboxi last week and it works.
To help debugging why "qca,clk-out-frequency" is not taking effect you could try this debug patch:
https://pastebin.com/raw/RKG63JGJ
This is the result on a imx6 hummingboard:
....
Net: ar803x_of_init: found PHY node: ethernet-phy at 0
********** clk out frequency is 125000000ar803x_of_init: flags=0 clk_25m_reg=0018 clk_25m_mask=0018 ******** PHY mode is 8
Warning: ethernet at 2188000 using MAC address from ROM
eth0: ethernet at 2188000
Hit any key to stop autoboot: 0
=>
Hi Fabio,
Quoted 38 lines · Fabio Estevam
Hi Soeren,
Quoted 4 lines · Soeren Moch
Unfortunately I have no access to my usual development board (and will not have until the v2020.07 release). I only can use an old board without working USB-OTG, limited to eMMC boot. So I tried to avoid bisecting, because a bad commit could completely brick this board.
Ok, understood.
We could check if the issue on your board is due to:
commit
6333cbb3817ed551cd7d4e92f7359c73ccc567fcAuthor: Michael Walle <[email protected]> Date: Thu May 7 00:11:58 2020 +0200phy: atheros: ar8035: remove static clock config
We can configure the clock output in the device tree. Disable the hardcoded one in here. This is highly board-specific and should have never been enabled in the PHY driver.
If bisecting shows that this commit breaks your board it probably depends on the clock output of your Atheros AR8035 PHY. Please have a look at
doc/device-tree-bindings/net/phy/atheros.txt. You need to set "clk-out-frequency = <125000000>" because that value was the hardcoded value until this commit.Signed-off-by Michael Walle <[email protected]>Acked-by Joe Hershberger <[email protected]>On your board, are you able to measure with a scope the AR8035
CLK_25Mpin?Prior to this commit the
CLK_25Mwas hardcoded to output a 125MHz clock.Now that this setting from the ar8035 phy driver is gone we should pass this information in some form:
Quoted 6 lines
- We tried via devicetree with the "qca,clk-out-frequency" property, but it did not work. This is an area where you could add some debug prints inside
drivers/net/phy/atheros.cand see if if qca,clk-out-frequency is being parsed correctly to configure a 125MHz clock output. This is the method I used on mx6cuboxi last week and it works.
The phy-handle was missing in the fec node. With this added everything works fine:
---8<---
arch/arm/dts/imx6q-tbs2910.dts +0 -0
@@ -105,9 +105,20 @@
?&fec {
??????? pinctrl-names = "default";
??????? pinctrl-0 = <&pinctrl_enet>;
+?????? phy-handle = <&phy>;
??????? phy-mode = "rgmii-id";
??????? phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; ??????? status = "okay";
+
+?????? mdio {
+?????????????? #address-cells = <1>; +?????????????? #size-cells = <0>;
+
+?????????????? phy: ethernet-phy at 4 { +?????????????????????? reg = <4>; +?????????????????????? qca,clk-out-frequency = <125000000>; +?????????????? };
+?????? };
?};
?
?&hdmi {
---8<---
Quoted 7 lines
- Other way to configure the AR803x is via board code. Please try to copy the
ar8031_phy_fixup()andboard_phy_config()fromboard/freescale/mx6sabresd/mx6sabresd.cinto your board file.(I plan to remove this board PHY code in mx6sabresd after 2020.07 and use "qca,clk-out-frequency" to do the job).
OK, so I think we should use the dts patch as fix for u-boot now and sync that to linux afterwards.
Do you want to send a proper patch for that? Otherwise I can do so.
Thanks for your help and suggestions,
Soeren
Fabio Estevam
reviewerHi Soeren,
Quoted 2 lines · Soeren Moch
The phy-handle was missing in the fec node. With this added everything works fine:
Ops :-)
Yes, I will submit this patch for U-Boot.
Thanks
Fabio Estevam
reviewerHi Tom,
Quoted 23 lines · Fabio Estevam
Hi Tom,
Quoted 3 lines · Tom Rini
Based on your follow-up patches, I think you'll be unsurprised it doesn't work. I get:
Net: Could not get PHY for FEC0: addr 0Now I understand why the PHY could not be found with the patches I sent.
On mx6cubox the AR8035 is clocked from a 25MHz clock coming from the i.MX6 GPIO16 pin.
My patch incorrectly removed this setting.
board/solidrun/mx6cuboxi/mx6cuboxi.c int board_mmc_init(bd_t *bis) · line 242
Quoted 6 lines
board/solidrun/mx6cuboxi/mx6cuboxi.c +6
-0+int ret =enable_fec_anatop_clock (0 ,ENET_25MHZ ); +if (ret) +return ret; + +/* set gpr1[ENET_CLK_SEL] */ +setbits_le32 (&iomuxc_regs->gpr[1 ],IOMUXC_GPR1_ENET_CLK_SEL_MASK );
Quoted 7 lines
enable_fec_anatop_clock()and GPR1 settings above must remain.In order to get patch 1 to work (the one that adds the qca,clk-out-frequency property ) you also need this FEC change:
https://pastebin.com/raw/mcKdwwTsI hope this helps.
Good news! I managed to get access to an imx6 humming board and managed to fix the Eternet issue.
I will submit the AR8035 fix.
Quoted 16 lines · Tom Rini
Quoted 14 lines · Fabio Estevam
Quoted 3 lines · Tom Rini
Ah. So this is probably why the DT being right isn't helping then. If you want to blind-convert I'm happy to test, otherwise do you have a similar board conversion for me to look at? Thanks!
Please try Vladimir's suggestion as it seems to be the less intrusive approach:
board/solidrun/mx6cuboxi/mx6cuboxi.c +0
-0@@ -321,7 +321,7 @@ int board_eth_init(bd_t *bis)if (!bus)return -EINVAL ;
Quoted 11 lines
Quoted 7 lines
board/solidrun/mx6cuboxi/mx6cuboxi.c +1
-1- phydev =phy_find_by_mask (bus,ETH_PHY_MASK ,PHY_INTERFACE_MODE_RGMII ); + phydev =phy_find_by_mask (bus,ETH_PHY_MASK ,PHY_INTERFACE_MODE_RGMII_ID );if (!phydev) { ret = -EINVAL ;goto free_bus;OK, tried that and not enough. Console says PHY autoneg completes, but DHCP still doesn't reply.
What about with the manual revert in place? What does phydev->interface print? Not only in atheros.c, but also in mx6cuboxi.c, right below this phy_find_by_mask call.
Trying to understand if this is your only problem or if there are more.
Quoted 30 lines · Vladimir Oltean
Quoted 16 lines · Tom Rini
Quoted 14 lines · Fabio Estevam
Quoted 3 lines · Tom Rini
Ah. So this is probably why the DT being right isn't helping then. If you want to blind-convert I'm happy to test, otherwise do you have a similar board conversion for me to look at? Thanks!
Please try Vladimir's suggestion as it seems to be the less intrusive approach:
board/solidrun/mx6cuboxi/mx6cuboxi.c +0
-0@@ -321,7 +321,7 @@ int board_eth_init(bd_t *bis)if (!bus)return -EINVAL ;Quoted 11 lines
Quoted 7 lines
board/solidrun/mx6cuboxi/mx6cuboxi.c +1
-1- phydev =phy_find_by_mask (bus,ETH_PHY_MASK ,PHY_INTERFACE_MODE_RGMII ); + phydev =phy_find_by_mask (bus,ETH_PHY_MASK ,PHY_INTERFACE_MODE_RGMII_ID );if (!phydev) { ret = -EINVAL ;goto free_bus;OK, tried that and not enough. Console says PHY autoneg completes, but DHCP still doesn't reply.
Quoted 4 lines
What about with the manual revert in place? What does
phydev->interfaceprint? Not only inatheros.c, but also inmx6cuboxi.c, right below thisphy_find_by_maskcall.
Trying to understand if this is your only problem or if there are more.
In fact there's one more 'manual' thing you can do.
Check if RX delay is enabled (bit 15 of debug register 0):
=> mdio write eTSEC1 0x1D 0
=> mdio read eTSEC1 0x1E
=> mdio write eTSEC1 0x1E <new value>
Check if TX delay is enabled (bit 8 of debug register 5):
=> mdio write eTSEC1 0x1D 5
=> mdio read eTSEC1 0x1E
=> mdio write eTSEC1 0x1E <new value>
(replace eTSEC1 with your mdio bus name from "mdio list")
Quoted 31 lines · Vladimir Oltean
Quoted 30 lines · Vladimir Oltean
Quoted 27 lines · Tom Rini
Quoted 19 lines · Fabio Estevam
Quoted 3 lines · Tom Rini
Ah. So this is probably why the DT being right isn't helping then. If you want to blind-convert I'm happy to test, otherwise do you have a similar board conversion for me to look at? Thanks!
Please try Vladimir's suggestion as it seems to be the less intrusive approach:
board/solidrun/mx6cuboxi/mx6cuboxi.c +1
-1@@ -321,7 +321,7 @@ int board_eth_init(bd_t *bis)if (!bus)return -EINVAL ; - phydev =phy_find_by_mask (bus,ETH_PHY_MASK ,PHY_INTERFACE_MODE_RGMII ); + phydev =phy_find_by_mask (bus,ETH_PHY_MASK ,PHY_INTERFACE_MODE_RGMII_ID );if (!phydev) { ret = -EINVAL ;Quoted 2 lines
goto free_bus;OK, tried that and not enough. Console says PHY autoneg completes, but DHCP still doesn't reply.
Quoted 6 lines
Quoted 4 lines
What about with the manual revert in place? What does
phydev->interfaceprint? Not only inatheros.c, but also inmx6cuboxi.c, right below thisphy_find_by_maskcall.
Trying to understand if this is your only problem or if there are more.In fact there's one more 'manual' thing you can do.
For this test, based on your previous email and the kernel dts files, I made the change to mx6cuboxi.c to pass PHY_INTERFACE_MODE_RGMII_ID to phy_find_by_mask(...).
Quoted 4 lines
Check if RX delay is enabled (bit 15 of debug register 0):
=> mdio write eTSEC10x1D0
=> mdio read eTSEC10x1E
=> mdio write eTSEC10x1E<new value>
=> mdio list
FEC:
0 - AR8035 <--> FEC
=> mdio write FEC 0x1D 0
=> mdio read FEC 0x1E
Reading from bus FEC
PHY at address 0:
30 - 0x82ee
... so it's enabled already.
Quoted 4 lines
Check if TX delay is enabled (bit 8 of debug register 5):
=> mdio write eTSEC10x1D5
=> mdio read eTSEC10x1E
=> mdio write eTSEC10x1E<new value>
=> mdio write FEC 0x1D 5
=> mdio read FEC 0x1E
Reading from bus FEC
PHY at address 0:
30 - 0x2d47
... so it's enabled already.
Or did I make a mistake? Thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200616/99df041a/attachment.sig>
Quoted 71 lines · Tom Rini
Quoted 31 lines · Vladimir Oltean
Quoted 30 lines · Vladimir Oltean
Quoted 27 lines · Tom Rini
Quoted 19 lines · Fabio Estevam
Quoted 3 lines · Tom Rini
Ah. So this is probably why the DT being right isn't helping then. If you want to blind-convert I'm happy to test, otherwise do you have a similar board conversion for me to look at? Thanks!
Please try Vladimir's suggestion as it seems to be the less intrusive approach:
board/solidrun/mx6cuboxi/mx6cuboxi.c +1
-1@@ -321,7 +321,7 @@ int board_eth_init(bd_t *bis)if (!bus)return -EINVAL ; - phydev =phy_find_by_mask (bus,ETH_PHY_MASK ,PHY_INTERFACE_MODE_RGMII ); + phydev =phy_find_by_mask (bus,ETH_PHY_MASK ,PHY_INTERFACE_MODE_RGMII_ID );if (!phydev) { ret = -EINVAL ;Quoted 2 lines
goto free_bus;OK, tried that and not enough. Console says PHY autoneg completes, but DHCP still doesn't reply.
Quoted 6 lines
Quoted 4 lines
What about with the manual revert in place? What does
phydev->interfaceprint? Not only inatheros.c, but also inmx6cuboxi.c, right below thisphy_find_by_maskcall.
Trying to understand if this is your only problem or if there are more.In fact there's one more 'manual' thing you can do.
For this test, based on your previous email and the kernel dts files, I made the change to
mx6cuboxi.cto passPHY_INTERFACE_MODE_RGMII_IDtophy_find_by_mask(...).Quoted 4 lines
Check if RX delay is enabled (bit 15 of debug register 0):
=> mdio write eTSEC10x1D0
=> mdio read eTSEC10x1E
=> mdio write eTSEC10x1E<new value>=> mdio list
FEC:
0 - AR8035 <--> FEC
=> mdio write FEC0x1D0
=> mdio read FEC0x1E
Reading from bus FEC
PHY at address 0:
30 -0x82ee
... so it's enabled already.Quoted 4 lines
Check if TX delay is enabled (bit 8 of debug register 5):
=> mdio write eTSEC10x1D5
=> mdio read eTSEC10x1E
=> mdio write eTSEC10x1E<new value>=> mdio write FEC
0x1D5
=> mdio read FEC0x1E
Reading from bus FEC
PHY at address 0:
30 -0x2d47
... so it's enabled already.
Quoted 4 lines
Or did I make a mistake? Thanks!
--
Tom
Yes, the PHY has RGMII delays enabled in both directions.
Quoted 29 lines · Vladimir Oltean
Quoted 16 lines · Tom Rini
Quoted 14 lines · Fabio Estevam
Quoted 3 lines · Tom Rini
Ah. So this is probably why the DT being right isn't helping then. If you want to blind-convert I'm happy to test, otherwise do you have a similar board conversion for me to look at? Thanks!
Please try Vladimir's suggestion as it seems to be the less intrusive approach:
board/solidrun/mx6cuboxi/mx6cuboxi.c +0
-0@@ -321,7 +321,7 @@ int board_eth_init(bd_t *bis)if (!bus)return -EINVAL ;Quoted 11 lines
Quoted 7 lines
board/solidrun/mx6cuboxi/mx6cuboxi.c +1
-1- phydev =phy_find_by_mask (bus,ETH_PHY_MASK ,PHY_INTERFACE_MODE_RGMII ); + phydev =phy_find_by_mask (bus,ETH_PHY_MASK ,PHY_INTERFACE_MODE_RGMII_ID );if (!phydev) { ret = -EINVAL ;goto free_bus;OK, tried that and not enough. Console says PHY autoneg completes, but DHCP still doesn't reply.
Quoted 4 lines
What about with the manual revert in place? What does
phydev->interfaceprint? Not only inatheros.c, but also inmx6cuboxi.c, right below thisphy_find_by_maskcall.
Trying to understand if this is your only problem or if there are more.
In both functions the value printed out for phydev->interface is the value passed to phy_find_by_mask(...).
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200616/2a09ceac/attachment.sig>